Nichicon F971A335MAA Solid tantalum electrolytic capacitor Datasheet

SOLID TANTALUM ELECTROLYTIC CAPACITORS
F97
Resin-molded Chip,
High Reliability
(High temperature /
moisture resistance) Series
Specifications
Item
Compliant to the RoHS directive (2002/95/EC).
Compliant to AEC-Q200.
Applications
Automotive electronics(Engine ECU)
Industrial equipment
--55 to +125˚C (Rated temperature : +85˚C)
Capacitance Tolerance
± 20%, ± 10% (at 120Hz)
Dissipation Factor
Refer to next page
ESR (100kHz)
Refer to next page
Leakage Current∗
• After 1 minute' s application of rated voltage,leakage current at 20˚C
is not more than 0.01CV or 0.5µA, whichever is greater.
• After 1 minute' s application of rated voltage,leakage current at 85˚C
is not more than 0.1CV or 5µA,whichever is greater.
• After 1 minute' s application of derated voltage,leakage current at
125˚C is not more than 0.125CV or 6.3µA,whichever is greater.
Capacitance Change
by Temperature
+15% Max. (at +125˚C)
+10% Max. (at +85˚C)
--10% Max. (at --55˚C)
Damp Heat
(Steady State)
At 85˚C, 85% R.H.,For 1000 hours (No voltage applied)
Capacitance Change • • • • • • Within ±10% of the initial value
Dissipation Factor • • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • • • • 125% or less than the initial specified value
Load Humidity
After 500 hour' s application of rated voltage in series with a 33Ω
resistor at 60˚C, 90 to 95% R.H.,capacitors meet the characteristics
requirements table below.
Capacitance Change • • • • • • Within ±10% of the initial value
Dissipation Factor • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • • • • 125% or less than the initial specified value
Temperature Cycles
At --55˚C / +125˚C,For 30 minutes each,1000 cycles
Capacitance Change • • • • • • Within ± 5% of the initial value
Dissipation Factor • • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • • • • • Initial specified value or less
Resistance
to Soldering Heat
10 seconds reflow at 260˚C, 5 seconds immersion at 260˚C.
Capacitance Change • • • • • • Within ± 5% of the initial value
Dissipation Factor • • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • • • • • Initial specified value or less
Solderability
After immersing capacitors completely into a solder pot at
245˚C for 2 to 3 seconds,more than 3/4 of their electrode area
shall remain covered with new solder.
Type numbering system (Example : 16V 3.3µF)
1
2
3
4
5
6
7
8
9
10
11
F 9 7 1 C 3 3 5 M A
Taping code
(Refer to page 333 for details)
Case code
Capacitance tolerance
Rated capacitance Rated voltage
Series
Drawing
A • B Case
L
C • N Case
W1
L
W1
Surge∗
H
H
W2
W2
S
S
Endurance∗
S
Dimensions
Case code
(mm)
L
3.2
3.5
6.0
7.3
A
B
C
N
W1
± 0.2
± 0.2
± 0.2
± 0.2
1.6
2.8
3.2
4.3
W2
± 0.2
± 0.2
± 0.2
± 0.2
1.2
2.2
2.2
2.4
± 0.1
± 0.1
± 0.1
± 0.1
H
1.6
1.9
2.5
2.8
± 0.2
± 0.2
± 0.2
± 0.2
Marking
Shear Test
After applying the pressure load of 5N
for 10 ± 1 seconds horizontally to the
center of capacitor side body which
has no electrode and has been 5N (0.51kg • f)
soldered beforehand on a substrate, For 10 ± 1 seconds
there shall be found neither exfoliation
nor its sign at the terminal electrode.
Terminal Strength
Keeping a capacitor surface-mounted on a substrate upside
down and supporting the substrate at both of the opposite
bottom points 45mm apart from the center of capacitor, the
pressure strength is applied with a
20
specified jig at the center of the R230
substrate so that substrate may
bend by 1mm as illustrated.
Then, there shall be found no
45
45
remarkable abnormality on the
capacitor terminals.
S
0.8 ± 0.2
0.8 ± 0.2
1.3 ± 0.2
1.3 ± 0.2
Month code
B Case
C Case
10
16r
10
16r
C475
N Case
47
10r
A Case
Month code
Rated Voltage (V)
Rated Capacitance
(Capacitance code ) Rated voltage (V) Rated Capacitance (µF)
Rated voltage
(Voltage code)
After application of surge in series with a 33Ω resistor at the
rate of 30 seconds ON, 30 seconds OFF,for 1000 successive
test cycles at 85˚C,capacitors shall meet the characteristic
requirements table below.
Capacitance Change • • • • • • Within ± 5% of the initial value
Dissipation Factor • • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • • • • • Initial specified value or less
After 2000 hours' application of rated voltage in series with a
3Ω resistor at 85˚C,or derated voltage in series with a 3Ω
resistor at 125˚C,capacitors shall meet the characteristic
requirements table below.
Capacitance Change • • • • • • Within ±10% of the initial value
Dissipation Factor • • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • • • • • Initial specified value or less
1mm
S
Performance Characteristics
Category
Temperature Range
∗ As for the surge and derated voltage at 125˚C, refer to page 332 for details.
Standard ratings
V
Cap.(µF)
0.47
0.68
1
1.5
2.2
3.3
4.7
6.8
10
15
22
33
47
68
100
Code
474
684
105
155
225
335
475
685
106
156
226
336
476
686
107
6.3
0J
•
A
B
•
•
•
N
N
•
B
B
A
B
A
A
B
16
1C
20
1D
25
1E
A
A
A
A
A
A
A
A
A
B
A
A
A
A
A
10
1A
•
B
B
B
C
C
A • B
B • C • N
(B) • C • N
N
(C) • (N)
A
• B
B
A • B • C
(B) • C
B • C • N
B • C • N
(C) • N
A • B
(B) • C
(B) • C
N
C • N
(A) • B
B
(B) • C
C
C • N
(C) • N
(N)
(N)
35
1V
A
A
(A)
(A) • B
B
(B) • C
C
(C) • N
N
( ) The series in parentheses are being developed.
Please contact to your local Nichicon sales office when these
series are being designed in your application.
CAT.8100B
SOLID TANTALUM ELECTROLYTIC CAPACITORS
F97
Standard Ratings
Case
code
Part Number
Leakage
Current
(µA)
Disspation
Factor
(%@120Hz)
ESR
(Ω@100kHz)
3.3
4.7
6.8
6.8
15
22
22
33
33
47
47
68
100
A
A
A
B
B
A
B
A
C
B
C
N
N
F970J335MAA
F970J475MAA
F970J685MAA
F970J685MBA
F970J156MBA
F970J226MAA
F970J226MBA
F970J336MAA
F970J336MCC
F970J476MBA
F970J476MCC
F970J686MNC
F970J107MNC
0.5
0.5
0.5
0.5
0.9
1.4
1.4
2.1
2.1
3.0
3.0
4.3
6.3
4
6
6
6
6
12
8
12
6
8
6
6
8
4.5
4.0
3.5
2.5
2.0
2.5
1.9
2.5
1.1
1.0
0.9
0.6
0.6
10V
2.2
3.3
4.7
4.7
6.8
10
10
15
22
22
33
33
33
47
47
68
A
A
A
B
B
A
B
B
A
B
B
C
N
C
N
N
F971A225MAA
F971A335MAA
F971A475MAA
F971A475MBA
F971A685MBA
F971A106MAA
F971A106MBA
F971A156MBA
F971A226MAA
F971A226MBA
F971A336MBA
F971A336MCC
F971A336MNC
F971A476MCC
F971A476MNC
F971A686MNC
0.5
0.5
0.5
0.5
0.7
1.0
1.0
1.5
2.2
2.2
3.3
3.3
3.3
4.7
4.7
6.8
4
4
6
6
6
6
6
6
15
8
8
6
6
8
6
6
5.0
4.5
4.0
2.8
2.5
3.0
2.0
2.0
3.0
1.9
1.9
1.1
0.7
0.9
0.7
0.6
16V
1.5
2.2
3.3
4.7
4.7
6.8
10
10
10
15
22
22
22
33
33
33
47
A
A
A
A
B
B
A
B
C
C
B
C
N
B
C
N
N
F971C155MAA
F971C225MAA
F971C335MAA
F971C475MAA
F971C475MBA
F971C685MBA
F971C106MAA
F971C106MBA
F971C106MCC
F971C156MCC
F971C226MBA
F971C226MCC
F971C226MNC
F971C336MBA
F971C336MCC
F971C336MNC
F971C476MNC
0.5
0.5
0.5
0.8
0.8
1.1
1.6
1.6
1.6
2.4
3.5
3.5
3.5
5.3
5.3
5.3
7.5
4
4
4
8
6
6
8
6
6
6
8
8
6
10
8
6
8
6.3
5.0
4.5
4.0
2.8
2.5
3.5
2.1
1.5
1.2
1.9
1.1
0.7
2.1
1.1
0.7
0.7
20V
0.68
1
1.5
2.2
3.3
4.7
4.7
6.8
10
15
22
22
A
A
A
A
B
A
B
C
C
N
C
N
F971D684MAA
F971D105MAA
F971D155MAA
F971D225MAA
F971D335MBA
F971D475MAA
F971D475MBA
F971D685MCC
F971D106MCC
F971D156MNC
F971D226MCC
F971D226MNC
0.5
0.5
0.5
0.5
0.7
0.9
0.9
1.4
2.0
3.0
4.4
4.4
4
4
4
6
4
8
6
6
6
6
8
6
7.6
7.5
6.7
6.3
3.1
4.0
2.8
1.8
1.5
0.7
1.1
0.7
Rated
Rated Volt Capacitance
(µF)
6.3V
Case
code
Part Number
Leakage
Current
(µA)
Disspation
Factor
(%@120Hz)
ESR
(Ω@100kHz)
25V
0.68
1
2.2
3.3
4.7
6.8
10
10
15
A
A
B
B
C
C
C
N
N
F971E684MAA
F971E105MAA
F971E225MBA
F971E335MBA
F971E475MCC
F971E685MCC
F971E106MCC
F971E106MNC
F971E156MNC
0.5
0.5
0.6
0.8
1.2
1.7
2.5
2.5
3.8
4
4
4
4
6
6
6
6
6
7.6
7.5
3.8
3.5
1.8
1.8
1.6
1.0
0.7
35V
0.47
0.68
1.5
2.2
3.3
4.7
6.8
10
A
A
B
B
C
C
N
N
F971V474MAA
F971V684MAA
F971V155MBA
F971V225MBA
F971V335MCC
F971V475MCC
F971V685MNC
F971V106MNC
0.5
0.5
0.5
0.8
1.2
1.6
2.4
3.5
4
4
4
4
4
6
6
6
10.0
7.6
4.0
3.8
2.0
1.8
1.0
1.0
Rated
Rated Volt Capacitance
(µF)
In case of capacitance tolerance ±10% type, K will be put at 9th digit of type
numbering system.
CAT.8100B