AIC1517 Dual USB High-Side Power Switch FEATURES DESCRIPTION • 110mΩ (5V Input) High-Side MOSFET Switch. The AIC1517 is a dual high-side power switch 700mA Continuous Load Current per Channel. for self-powered and bus-powered Universal 110µA Typical On-State Supply Current. Serial Bus (USB) applications. Both high-side 1µA Typical Off-State Supply Current. switches are MOSFET with 110m Ω RDS(ON), Current-Limit / Short Circuit Protection. which meets USB voltage drop requirements for Fault Flag with 3ms filter eliminates false maximum transmission wire length. assertions. (1517D) Multi-purpose Thermal Shutdown Protection under Overcurrent indicates Condition. shutdown, or undervoltage lockout for each Undervoltage Lockout Ensures that Switch is off open-drain over-current fault flag limiting, output thermal channel. Output current is typically limited to 0.85A, and the thermal shutdown functions of at Start Up. the power switches independently control their Open-Drain Fault Flag. Slow Turn ON and Fast Turn OFF. Enable Active-High or Active-Low. channel under overcurrent condition. Guaranteed minimum output rise time limits inrush current during hot plug-in as well as minimizing EMI and prevents the voltage at upstream port from dropping excessively. APPLICATIONS USB Power Management. Hot Plug-In Power Supplies. Battery-Charger Circuit. Analog Integrations Corporation Si-Soft Research Center 3A1, No.1, Li-Hsin Rd. I, Science Park, Hsinchu 300, Taiwan, R.O.C. TEL: 886-3-5772500 FAX: 886-3-5772510 www.analog.com.tw DS-1517G-02 072209 1 AIC1517 TYPICAL APPLICATION CIRCUIT Vcc +5v 10K 10K ON 1 OFF 2 3 ON 4 OFF CTLA OUTA FLGA IN FLGB GND CTLB OUTB 8 OUTA 7 0.1uF 6 33uF 5 OUTB AIC1517 33uF ORDERING INFORMATION AIC1517X-XXXXX PACKING TYPE TR: TAPE & REEL TB: TUBE PACKAGING TYPE S8: SOP-8 G: GREEN PACKAGE CONTROL POLARITY 0: Active Low 1: Active High PIN CONFIGURATION SOP-8 TOP VIEW CTLA 1 FLGA 2 8 OUTA 7 IN FLGB 3 6 GND CTLB 4 5 OUTB Fault Flag Response Delay Time D: Delay 3ms N: No Example: AIC1517D-0GS8TR Delay 3ms, Active Low Version, in SOP-8 Green Package & Taping & Reel Packing Type AIC1517N-1GS8TR No Delay, Active High Version, in SOP-8 Green Package & Taping & Reel Packing Type 2 AIC1517 ABSOLUTE MAXIMUM RATINGS Supply Voltage (VIN) 7.0V Fault Flag Voltage (VFLG) 7.0V Fault Flag Current (IFLG) 50mA Control Input (VCTL) -0.3V ~7V -40°C~85°C Operating Temperature Range Junction Temperature 150°C Storage Temperature Range -65°C ~ 150°C 260°C Lead Temperature (Soldering, 10sec) Thermal Resistance, θ JA (Junction to Ambient) SOP-8 160°C/W (Assume no Ambient Airflow, no Heatsink) Thermal Resistance, θ JC (Junction to Case) SOP-8……………………………………40°C /W Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. 3 AIC1517 ELECTRICAL CHARACTERISTICS (VIN= 5V, TA=25°°C, unless otherwise specified.) (Note 1) PARAMETERS CONDITIONS Supply Voltage Supply Current Control Input Voltage Control Input Current MIN. TYP. 3.1 MAX. UNIT 6.0 V VCTL =Logic “0”, OUT=Open 0.75 5 VCTL =Logic “1”, OUT=Open 110 160 VCTL =Logic “0” VCTL =Logic “1” 0.8 2.4 VCTL =Logic “0” 0.01 1 VCTL =Logic “1” 0.01 1 Control Input Capacitance 1 Output MOSFET Resistance µA V µA pF 110 150 mΩ Output Turn-On Rise Delay RL = 10Ω each Output 600 1000 µS Output Turn-On Rise Time RL = 10Ω each Output 1800 3000 µS Output Turn-Off Delay RL = 10Ω each Output 0.8 20 µS Output Turn-Off Fall Time RL = 10Ω each Output 0.7 20 µS 10 µA Output Leakage Current Current Limit Threshold Over Current Flag Response Delay(Note2) Apply VOUT = 0V until FLG low 0.72 0.85 0.98 A 1.5 3 7 ms Over Temperature Shutdown TJ Increasing 135 Threshold TJ Decreasing 125 Error Flag Output Resistance VIN = 5V, IL =10 mA 15 30 VIN = 3.3V, IL =10mA 15 40 °C Error Flag Off Current VFLG = 5V 0.01 1 UVLO Threshold VIN Increasing 2.85 3.05 VIN Decreasing 2.45 2.65 Ω µA V Note 1: Specifications are production tested at TA=25°C. Specifications over the -40°C to 85°C operating temperature range are assured by design, characterization and correlation with Statistical Quality Controls (SQC). Note 2: This parameter belongs to AIC1517D-XXXXX. 4 AIC1517 TYPICAL PERFORMANCE CHARACTERISTICS 120 140 IL=100mA O TA=25 C 100 ON Resistance (m Ω) ON Resistance (m Ω) 120 100 80 60 40 IL=100mA O TA=25 C 80 60 40 20 20 0 3.0 3.5 Fig. 1 4.0 4.5 5.0 5.5 0 -40 6.0 Supply Voltage (V) ON Resistance vs. Supply Voltage -20 0 20 40 60 80 100 Temperature (°C) ON Resistance vs. Temperature Fig. 2 150 3.4 140 Supply Current (µA) Threshold Voltage (V) 3.2 Rising 3.0 2.8 Falling 2.6 2.4 Fig. 3 Both Switches ON 100 90 60 -20 0 20 40 60 80 3.0 100 Temperature (°C) UVLO Threshold Voltage vs. Temperature 3.5 4.0 4.5 5.0 5.5 6.0 Supply Voltage (V) ON-State Supply Current vs. Supply Voltage Fig. 4 0.25 95 0.20 90 Supply Current (µA) Supply Current (µA) 110 70 100 85 80 Both Switch ON 75 70 65 60 -40 120 80 2.2 2.0 -40 130 0.15 0.10 Both Switch Off 0.05 0.00 -20 Fig. 5 0 20 40 60 80 Temperature (°C) ON State Current vs. Temperature 100 -40 -20 Fig. 6 0 20 40 60 80 100 Temperature (°C) OFF-State Current vs. Temperature 5 AIC1517 TYPICAL PERFORMANCE CHARACTERISTICS (Continued) 2.5 0.04 Enable Threshold Supply Current (µA) 2.0 0.03 0.02 0.01 Both Switch Off 1.5 1.0 0.5 0.00 0.0 3.0 3.5 Fig. 7 4.0 4.5 5.0 5.5 3.0 6.0 Supply Voltage (V) OFF-State Current vs. Supply Voltage Fig. 8 4.0 4.5 5.0 5.5 6.0 Supply Voltage (V) Enable Threshold vs. Supply Voltage 1.0 0.9 0.9 0.8 0.8 Current Limit (m A) 0.7 Current Limit (m A) 3.5 0.6 0.5 0.4 0.3 0.2 0.1 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 -40 0.0 3.0 3.5 Fig. 9 4.0 4.5 5.0 5.5 6.0 Supply Voltage (V) Current Limit vs. Supply Voltage -20 0 40 60 80 100 Temperature (°C) Current Limit vs. Temperature Fig. 10 1.8 20 2.0 1.6 Rising Time (m S) Rising Time (m S) 1.4 1.2 1.0 0.8 0.6 0.4 1.5 1.0 0.5 0.2 0.0 3.0 3.5 Fig. 11 4.0 4.5 5.0 5.5 6.0 Supply Voltage (V) Rising Time vs. Supply Voltage 0.0 -40 -20 Fig. 12 0 20 40 60 80 100 Temperature (°C) Rising Time vs. Temperature 6 AIC1517 4.0 4.0 3.5 3.5 Flag Delay Time (m S) Flag Delay Time (m S) TYPICAL PERFORMANCE CHARACTERISTICS 3.0 2.5 2.0 1.5 1.0 (Continued) 3.0 2.5 2.0 1.5 1.0 0.5 0.5 0.0 3.0 3.5 Fig. 13 4.0 4.5 5.0 5.5 6.0 0.0 -40 -20 Supply Voltage (V) Flag Delay Time vs. Supply Voltage CL =10uF RL =10Ω 0 Fig. 14 20 40 60 80 100 Temperature (°C) Flag Delay Time vs. Temperature CL =10uF RL =10Ω CTL CTL VOUT VOUT Fig. 15 Fig. 16 Turn ON Time Turn OFF Time VOUT VIN FLAG VOUT IIN Fig. 17 Current Limit Event Fig. 18 UVLO Protection 7 AIC1517 BLOCK DIAGRAM PIN DESCRIPTIONS PIN 1: CTLA - Controls the turn-on/turn-off of channel A MOSFET with TTL as a control input. Active high for AIC1517-1 and active low for AIC1517-0. PIN 4: CTLB - Controls the turn-on/turn-off of channel B MOSFET with TTL as a control input. Active High for AIC1517-1 and active low for AIC1517-0. PIN 2: FLGA - An active-low and open-drained fault flag output for channel A. FLGA is an indicator for current limit when CTLA is active. In normal mode operation (CTLA or/and CLTB is active), it also can indicate thermal shutdown or undervoltage. PIN 5: OUTB - Channel B MOSFET switch output. PIN 6: GND - Chip power ground. PIN 7: IN - Power supply input. PIN 8: OUTA - Channel A MOSFET switch output. PIN 3: FLGB - An active-low and open-drained fault flag output for channel B. FLGB is an indicator for current limit when CTLB is active. In normal mode operation (CTLB or/and CLTA is active), it also can indicate thermal shutdown or undervoltage. 8 AIC1517 APPLICATION INFORMATION Error Flag Supply Filtering An error Flag is an open-drained output of an A 0.1µF to 1µF bypass capacitor from IN to GND, N-channel MOSFET. FLG output is pulled low to located signal the following fault conditions: input recommended to control supply transients. undervoltage, output current limit, and thermal Without a bypass capacitor, an output short may shutdown. The Fault Flag response delay time is cause sufficient ringing on the input (from supply 3ms. lead inductance) to damage internal control near the device, is strongly circuitry. Current Limit The current limit threshold is preset internally. It Transient Requirements protects the output MOSFET switches from USB supports dynamic attachment (hot plug-in) damage resulting from undesirable short circuit of peripherals. A current surge is caused by the conditions or excess inrush current, which is input capacitance of downstream device. Ferrite often encountered during hot plug-in. The low beads are recommended in series with all power limit of the current limit threshold of the AIC1517 and ground connector pins. Ferrite beads allows a minimum current of 0.64A through the reduce EMI and limit the inrush current during MOSFET switches. The error flag signals when hot-attachment any current limit conditions occur. signals. Thermal Shutdown by filtering high-frequency Short Circuit Transient When temperature of AIC1517 exceeds 135°C Bulk for any reasons, the thermal shutdown function transient turns both MOSFET switches off and signals the hot-attachment event. A 33µF/16V tantalum or a error flag. A hysteresis of 10°C prevents the 100µF/10V electrolytic capacitor mounted close MOSFETs from turning back on until the chip to downstream connector each port should temperature drops below 125°C. However, if provide transient drop protection. thermal shutdown is triggered by chip temperature rise resulting from overcurrent fault condition of either one of the MOSFET switches, the thermal shutdown function will only turn off the switch that is in overcurrent condition and the other switch can still remain its normal capacitance current provides the needed short-term during a Printed Circuit Layout The power circuitry of USB printed circuit boards requires a customized layout to maximize thermal dissipation and to minimize voltage drop and EMI. operation. In other words, the thermal shutdown function of the two switches is independent of each other in the case of overcurrent fault. 9 AIC1517 APPLICATION CIRCUIT VCC 5.0V 10K 33µF 4.50V to 5.25V Upstream VBUS 100mA max 10K AIC1748 VBUS IN USB Controller 1µF CIN DGND GND ON/OFF CTLA OUTA OVERCURRENT FLGA IN OVERCURRENT FLGB GND VIN OUT D+ 1µF COUT Ferrite Bead AIC1517 ON/ VBUS 0.1µF 100µF D+ 0.01µF DGND CTLB OUTB GND DATA DATA VBUS 100µF D+ 0.01µF DGND DATA Fig. 19 Two-Port Self-Powered Hub 10 AIC1517 PHYSICAL DIMENSIONS (unit: mm) SOP-8 D E e A H °5 4 X h A SEE V IE W B A B 1A W ITH PLATIN G BA SE M ETAL 52 .0 L VIEW B C SEC TIO N A-A G AU G E PLA N E SEA TIN G PLAN E θ Note: 1. Refer to JEDEC MS-012AA. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side . 3. Dimension "E" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. SOP-8 S Y M B O L MIN. MAX. A 1.35 1.75 A1 0.10 0.25 B 0.33 0.51 C 0.19 0.25 D 4.80 5.00 E 3.80 4.00 MILLIMETERS e 1.27 BSC H 5.80 6.20 h 0.25 0.50 L 0.40 1.27 θ 0° 8° Note: Information provided by AIC is believed to be accurate and reliable. However, we cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in an AIC product; nor for any infringement of patents or other rights of third parties that may result from its use. We reserve the right to change the circuitry and specifications without notice. Life Support Policy: AIC does not authorize any AIC product for use in life support devices and/or systems. Life support devices or systems are devices or systems which, (I) are intended for surgical implant into the body or (ii) support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 11