HI-8195, HI-8196, HI-8197 28Ω QUAD SPST ANALOG SWITCH Open Circuit when Power Off December 2011 GENERAL DESCRIPTION FEATURES The HI-8195 is a quad analog CMOS switch fabricated with Silicon-on-Insulator (SOI) technology for latch-up free operation and maximum switch isolation. These switches are ideally suited for applications demanding low switch leakage when the power pins are 0V. · CMOS analog switches with up to +/-10V Common Mode Range · Superior ESD protection > 4KV HBM · Fast switching time with break-before-make · Low power · Extended Temperature Range (-55°C to +125°C) PIN CONFIGURATIONS (Top Views) IN1 1 16 IN2 S1A 2 15 S2A S1B 3 14 S2B V- 4 13 V+ GND 5 12 VLOGIC S4B 6 11 S3B S4A 7 10 S3A IN4 8 9 IN3 HI-8195PSx, HI-8195PDx 16-Pin SO or DIP package 16 S1A Industry-standard plastic package options include 16-pin SOIC, DIP and QFN. Ceramic packaging is available on request. All three products are offered in both industrial (-40°C to +85°C) and extended (-55°C to +125°C) temperature range options. · SOI switch isolation with 1nA typical Off leakage 14 IN2 The HI-8195 provides four each normally open switches when the switch control inputs are low. The HI-8196 provides four each normally closed switches when the switch control inputs are low. The HI-8197 provides a combination of two normally closed and two normally open switches. · Switch nodes are open-circuit when chip is powered down 13 S2A These switches conduct equally well in either direction. Power down and Off state leakages are less than 10nA maximum. Charge injection is less than 10pC. Switching times with a 3.3V VLOGIC supply are typically 55ns to the On state and 35ns to the Off state. · Robust CMOS Silicon-on-Insulator (SOI) technology 15 IN1 The logic supply (VLOGIC) can be independently set from 2.5V to 5V without changing the switch resistance (RON). With V+/V- set at +/-15V and a signal range from +5V to -5V, the RON maximum is 28W at 25°C and the maximum deviation from flat is typically less than 10%. · 28 W max at 25°C with Common Mode < +/-5V S1B 1 12 S2B V- 2 11 V+ GND 3 10 VLOGIC S4B 4 · Avionics · Data bus isolation IN3 7 S3B S3A 8 IN4 6 S4A 5 APPLICATIONS 9 HI-8195PCx 16-pin 5mm x 5mm Chip-scale package · Sample-and-Hold circuits · Test Equipment · Communications Systems (DS8195 Rev. New) PRODUCT OPTIONS PART TYPE IN1 HI-8195 0 1 HI-8196 0 1 HI-8197 0 1 HOLT INTEGRATED CIRCUITS www.holtic.com Switch 1 Open Closed Closed Open Open Closed IN2 0 1 0 1 0 1 Switch 2 Open Closed Closed Open Closed Open IN3 0 1 0 1 0 1 Switch 3 Open Closed Closed Open Closed Open IN4 0 1 0 1 0 1 Switch 4 Open Closed Closed Open Open Closed 12/11 HI-8195, HI-8196, HI-8197 PIN DESCRIPTIONS SIGNAL FUNCTION IN1 S1A S1B VGND S4B S4A IN4 IN3 S3A S3B VLOGIC V+ S2B S1B IN2 Logic Input Switch Node Switch Node Supply Supply Switch Node Switch Node Logic Input Logic Input Switch Node Switch Node Supply Supply Switch Node Switch Node Logic input V+/V- = 15.0V 70W V+/V- = 10.0V 60W 60W 50W 50W RON RON 70W DESCRIPTION HI-8195 and HI-8197 are normally Open when input Low Switch 1 Node Switch 1 Node Negative supply Reference Ground Switch 4 Node Switch 4 Node HI-8195 and HI-8197 are normally Open when input Low HI-8196 and HI-8197 are normally Closed when input Low Switch 3 Node Switch 3 Node 3.3V or 5.0V Logic supply Positive supply Switch 2 Node Switch 2 Node HI-8196 and HI-8197 are normally Closed when input Low 40W 30W 20W 20W 10W 10W -10V -5V 0V VSWITCH 5V 10V Typical RON as a function of VSUPPLY and VSWITCH (10mA switch current, 25°C) 15V T = -55C T = +25C 40W 30W -15V T = +125C -15V -10V -5V 0V VSWITCH 5V 10V 15V Typical RON as a function of VSWITCH and Temperature (10mA switch current, VSUPPLY =+/-15V) HOLT INTEGRATED CIRCUITS 2 HI-8195, HI-8196, HI-8197 ABSOLUTE MAXIMUM RATINGS (Voltages referenced to GND = 0V) Supply Voltage, V+: ............................................................................16.5V Continuous Power Dissipation (TA=70°C): Supply Voltage, V-:.............................................................................-16.5V SO Package (derate 6.7mW/°C above 70°C)...................696mW Supply Voltage, VLOGIC .........................................................................5.5V Plastic DIP (derate 10.53 mw/°C above 70°C) .................842mW Switch Current (either direction, DC): .................................................20mA Thin QFN (derate 21.3mW/°C above 70°C) ...................1702mW Peak Switch Current (1 ms pulse, 10% duty cycle max.)..................100mA Digital Input Voltage (IN1-4):.....................................-0.3V to VLOGIC + 0.3V Storage Temperature Range: ......................................-65°C to +150°C Operating Temperature Range: (Industrial)..........................-40°C to +85°C (Hi-Temp) ........................-55°C to +125°C Soldering Temperature: (Ceramic)......................60 sec. at +300°C (Plastic - leads).............10 sec. at +280°C (Plastic - body) .....................+260°C Max. Maximum Junction Temperature ........................................................175°C NOTE: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS V+ = 15V, V- = -15V, GND = 0V. Operating temperature range (unless otherwise noted). VLOGIC = 3.3V PARAMETER SYMBOL CONDITIONS FIGURE RON V+/V-=+/-15V, Vs=+/-5V V+/V-=+/-15V, Vs=+/-10V V+/V-=+/-10V, Vs=+/-5V 1 1 1 |ISWLEAK| Switch voltage ± 10V, 25°C 2 |ISWLEAK| Switch voltage ± 10V, 125° 2 |ISWLEAK| Switch voltage ± 10V, -55°C 2 150 VLOGIC = 5.0V MIN TYP MAX MIN 18 18 20 24 27 28 28 31 32 18 18 20 UNIT TYP MAX 24 27 28 28 31 32 W W W 5 5 nA 20 20 nA 150 nA SWITCH PARAMETERS Switch Resistance 25°C, 10mA Leakage (open circuit and power down) LOGIC INPUTS Input High Voltage VIH 70 70 %VLOGIC Input Low Voltage VIL Input Current IIN VIN = 0V or VIN=VLOGIC VLOGIC Current IDD1 Any state 0.5 0.5 μA V+ Current IDD2 Any state 0.5 0.5 μA V- Current IEE Any state TON V+/V- = ±10V, 25°C VS = ±10V, -55°C to +125°C 3 3 55 V+/V- = ±10V, 25°C VS = ±10V, -55°C to +125°C 3 3 35 10V signal, 25°C 10V signal, -55°C to +125°C 4 4 30 -0.5 0.5 30 -0.5 0.5 %VLOGIC μA SUPPLY -0.5 μA -0.5 DYNAMIC PARAMETERS Turn On Time Turn Off time Break-Before-Make Time TOFF TD 35 75 ns ns 25 ns ns 20 40 8 4 55 8 ns ns 4 Charge Injection Q VS=0V, RS=0W, 25°C 5 -10 -10 pC Off Isolation RR f = 1 MHz, 25°C 6 65 65 dB Crosstalk CR f = 1 MHz, 25°C 7 90 90 dB COFF CON Switch Off, 25°C Switch On, 25°C 8 9 12 46 12 46 pF pF Capacitance HOLT INTEGRATED CIRCUITS 3 HI-8195, HI-8196, HI-8197 TEST CIRCUITS IDS V1 SA VS + - RON = V1/IDS + - VS Figure 1 - On Resistance +5V 0.1μF 0.1μF VIN (HI-8196) V+ SA VD + - Figure 2 - Off Leakage +15V VLOGIC ID(OFF) SB A IS(OFF) SA A SB 50% 50% 50% 50% VIN (HI-8195) SB VOUT IN VS GND + - 90% 300W 35pF V- 50% VOUT 0.1μF -15V t ON t OFF Figure 3. Switching Times 0.1μF +5V +15V VLOGIC V+ 0.1μF 5V VIN 50% 50% 0V VS1 VS2 S1A S1B S2A S2B IN VOUT1 VOUT2 35pF GND V- 35pF 0.1μF 90% 50% VOUT1 300W 300W 90% VOUT2 50% -15V tD Figure 4. Break-Before-Make Time Delay (HI-8197) HOLT INTEGRATED CIRCUITS 4 tD HI-8195, HI-8196, HI-8197 RS +5V +15V VLOGIC V+ SA SB VOUT VIN IN VS GND + - CL 10nF V- DVOUT VOUT -15V QINJ = CL x DVOUT Figure 5. Charge Injection 0.1μF 0.1μF +5V +15V VLOGIC 0.1μF +15V VLOGIC V+ SA1 V+ SA +5V SB VOUT 0.1μF SB1 50W IN1 VS IN IN2 GND 50W V- VS 0.1μF SB2 VOUT 50W -15V SA2 GND NC V0.1μF -15V Figure 7 - Channel-to-Channel Crosstalk Figure 6 - Off Isolation 0.1μF +5V +15V VLOGIC V+ SA Capacitance Meter f=1MHz 0.1μF 0.1μF SB +15V VLOGIC V+ SA Capacitance Meter f=1MHz IN GND +5V V- SB VS IN GND V- 0.1μF 0.1μF -15V -15V Figure 8 - Off Capacitance Figure 9 - On Capacitance HOLT INTEGRATED CIRCUITS 5 0.1μF HI-8195, HI-8196, HI-8197 ORDERING INFORMATION HI - 819x xx x x PART NUMBER Blank F PART NUMBER LEAD FINISH Tin / Lead (Sn / Pb) Solder Pb-free, RoHS compliant TEMPERATURE RANGE FLOW BURN IN I -40°C TO +85°C I NO T -55°C TO +125°C T NO M -55°C TO +125°C M YES PART NUMBER PACKAGE DESCRIPTION PC 16 PIN PLASTIC 5 x 5 mm CHIP SCALE (16PCS1) (No M-flow, Pb-free only) PS 16 PIN PLASTIC NARROW BODY SOIC (16HN) PD 16 PIN PLASTIC DIP (16P) PART NUMBER FUNCTION 8195 QUAD SWITCH, NORMALLY OPEN 8196 QUAD SWITCH, NORMALLY CLOSED 8197 QUAD SWITCH, TWO NORMALLY OPEN, TWO NORMALLY CLOSED HOLT INTEGRATED CIRCUITS 6 HI-8195, HI-8196, HI-8197 REVISION HISTORY P/N Rev Date DS8195 NEW 12/08/11 Description of Change Initial Release HOLT INTEGRATED CIRCUITS 7 HI-8195 PACKAGE DIMENSIONS inches (millimeters) 16-PIN PLASTIC SMALL OUTLINE (SOIC) - NB (Narrow Body) .0087 ± .0012 (.220 ± .029) .390 ± .004 (9.90 ± .10) .236 ±.008 (5.99 ±.20) Package Type: 16HN .1525 ± .0025 (3.87 ± .06) Top View See Detail A .0165 ± .003 (.419 ± .089) .061 ± .007 (1.549 ± .178) .050 BSC (1.27) 0° to 8° .0069 ± .0029 (.176 ± .074) .033 ± .017 (.838 ± .432) BSC = “Basic Spacing between Centers” is theoretical true position dimension and has no tolerance. (JEDEC Standard 95) Detail A millimeters 16-PIN PLASTIC CHIP-SCALE PACKAGE Package Type: 16PCS1 Electrically isolated metal heat sink on bottom of package 3.38 ± 0.05 (0.133 ± 0.002) 3.38 ± 0.05 (0.133 ± 0.002) Top View 5.00 ± 0.05 (0.197 ± 0.002) Connect to any ground or power plane for optimum thermal dissipation Bottom View 5.00 ± 0.05 (0.197 ± 0.002) .50 ± 0.05 (0.020 ± 0.002) 0.20 (0.008) min. 0.75 ± 0.05 (0.03 ± 0.002) 0.203 (0.008) 0.025 ± 0.025 (0.001 ± 0.001) 0.80 (0.031) BSC REF. 0.30 ± 0.05 (0.012 ± 0.002) HOLT INTEGRATED CIRCUITS 8 BSC = “Basic Spacing between Centers” is theoretical true position dimension and has no tolerance. (JEDEC Standard 95) HI-8195 PACKAGE DIMENSIONS 16-PIN PLASTIC DIP Package Type: 16P 0.745 (18.923) 0.810 (20.574) 0.240 (6.096) 0.260 (6.604) 0.290 (7.366) 0.310 (7.874) 0.015 (0.381) 0.035 (0.889) 0.125 (3.175) 0.150 (3.810) 0.120 (3.048) 0.150 (3.810) 0.015 (0.381) 0.023 (0.584) 0.100 (2.54) BSC. 0.045 (1.143) 0.065 (1.651) HOLT INTEGRATED CIRCUITS 9 0.008 (0.203) 0.015 (0.381) 0.300 (7.620) 0.370 (9.398) inches (millimeters)