ER1000FCT THRU ER1004FCT ISOLATION SUPERFAST RECOVERY RECTIFIERS VOLTAGE - 50 to 400 Volts CURRENT - 10.0 Amperes FEATURES l Plastic package has Underwriters Laboratory Flammability Classification 94V-O utilizing Flame Retardant Epoxy Molding Compound l Exceeds environmental standards of MIL-S-19500/228 l Low power loss, high efficiency l Low forward voltage, high current capability l High surge capacity l Super fast recovery times, high voltage l Epitaxial chip construction ITO-220AB MECHANICAL DATA Case: ITO-220AB full molded plastic package Terminals: Leads, solderable per MIL-STD-202, Method 208 Polarity: As marked Mounting Position: Any Weight: 0.08 ounces, 2.24 grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 ¢J ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, Resistive or inductive load. For capacitive load, derate current by 20%. ER1000FC ER1001FC T T Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at TC=100 ¢J 50 35 50 ER1001A FCT 100 70 100 150 105 150 Peak Forward Surge Current, 8.3ms single half sine-Wave superimposed on rated load(JEDEC method) Maximum Forward Voltage at 5.0A per element Maximum DC Reverse Current at Rated TC=25 ¢J ER1002FC ER1003FC ER1004FC T T T 200 140 200 NOTES: 1. Measured at 1 MHz and applied reverse voltage of 4.0 VDC 2. Reverse Recovery Test Conditions: IF=.5A, IR=1A, Irr=.25A 3. Thermal resistance junction to CASE 400 320 400 V V V 10.0 A 150 A 0.95 DC Blocking Voltage per element TC=100 ¢J Typical Junction capacitance (Note 1) Maximum Reverse Recovery Time(Note 2) Typical Thermal Resistance(Note 3) R £KJC Operating and Storage Temperature Range TJ 300 210 300 UNITS 1.30 £g A 5 500 42 35 PF 50 3.0 -55 to +150 V ns ¢J /W ¢J INSTANTANEOUS FORWARD CURRENT AMPERES AVERAGE FORWARD CURRENT, AMPERES RATING AND CHARACTERISTIC CURVES ER1000FCT THRU ER1004FCT 10 8 6 4 2 0 0 50 100 40 20 50. 100. 150. 200V 10 8 6 4 2 300. 400V 1.0 .8 . .6 .4 TJ = 25¢J PULSE WIDTH = 200£gs .2 .1 .6 150 .7 .8 9 1.0 1.1 1.2 1.3 INSTANTANEOUS FORWARD CHARACTERISTIC Fig. 1-FORWARD CURRENT DERATING CURVE Fig. 2-TYPICAL INSTNATANEOUS FORWARD CHARACTERISTIC 1000 TC = 100 ¢J 100 TC = 75¢J 10 TC = 25¢J 1 .01 0 100 200 300 PEAK FORWARD SURGE CURRENT, AMPERES INSTANTANEOUS REVERSE CURRENT, MILLAMPERES CASE TEMPERATURE, ¢J 150 130 110 90 70 8.3ms SINGLE HALF SINE WAVE JEDEC METHOD 50 30 20 10 1 2 5 10 20 50 100 NO. OF CYCLES AT 60Hz Fig. 4-MAXIMUM NON-REPETITIVE SURGE CURRENT . 80 CAPACITANCE, pF Fig. 3-TYPICAL REVERSE CHARACTERISTICS 70 60 TJ = 25 ¢J 50 40 30 1 2 5 20 50 100 200 500 REVERSE VOLTAGE, VOLTS Fig. 5-TYPICAL JUNCTION CAPACITANCE