TI1 LP2985IM5-3.8 Micropower 150 ma low-noise ultra low-dropout regulator in sot-23 and micro smd packages designed for use with very low esr output capacitor Datasheet

LP2985
LP2985 Micropower 150 mA Low-Noise Ultra Low-Dropout Regulator in SOT-23
and micro SMD Packages Designed for Use with Very Low ESR Output
Capacitors
Literature Number: SNVS018U
LP2985
Micropower 150 mA Low-Noise Ultra Low-Dropout
Regulator in SOT-23 and micro SMD Packages
Designed for Use with Very Low ESR Output Capacitors
General Description
Features
The LP2985 is a 150 mA, fixed-output voltage regulator designed to provide ultra low-dropout and low noise in battery
powered applications.
Using an optimized VIP® (Vertically Integrated PNP) process,
the LP2985 delivers unequalled performance in all specifications critical to battery-powered designs:
Dropout Voltage: Typically 300 mV @ 150 mA load, and
7 mV @ 1 mA load.
Ground Pin Current: Typically 850 µA @ 150 mA load, and
75 µA @ 1 mA load.
Enhanced Stability: The LP2985 is stable with output capacitor ESR as low as 5 mΩ, which allows the use of ceramic
capacitors on the output.
Sleep Mode: Less than 1 µA quiescent current when ON/OFF
pin is pulled low.
Smallest Possible Size: SOT-23 and micro SMD packages
use absolute minimum board space.
Precision Output: 1% tolerance output voltages available (A
grade).
Low Noise: By adding a 10 nF bypass capacitor, output noise
can be reduced to 30 µV (typical).
Multiple voltage options, from 2.5V to 5.0V, are available as
standard products. Consult factory for custom voltages.
■
■
■
■
■
■
■
■
■
■
■
■
■
■
Ultra low dropout voltage
Guaranteed 150 mA output current
Smallest possible size (SOT-23, micro SMD package)
Requires minimum external components
Stable with low-ESR output capacitor
<1 µA quiescent current when shut down
Low ground pin current at all loads
Output voltage accuracy 1% (A Grade)
High peak current capability
Wide supply voltage range (16V max)
Low ZOUT: 0.3Ω typical (10 Hz to 1 MHz)
Overtemperature/overcurrent protection
−40°C to +125°C junction temperature range
Custom voltages available
Applications
■
■
■
■
Cellular Phone
Palmtop/Laptop Computer
Personal Digital Assistant (PDA)
Camcorder, Personal Stereo, Camera
Block Diagram
10014001
VIP® is a registered trademark of National Semiconductor Corporation.
© 2011 National Semiconductor Corporation
100140
www.national.com
LP2985 Micropower 150 mA Low-Noise Ultra Low-Dropout Regulator in SOT-23 and micro SMD
Packages
April 26, 2011
LP2985
Basic Application Circuit
10014002
*ON/OFF input must be actively terminated. Tie to VIN if this function is not to be used.
**Minimum capacitance is shown to ensure stability (may be increased without limit). Ceramic capacitor required for output (see Application Hints).
***Reduces output noise (may be omitted if application is not noise critical). Use ceramic or film type with very low leakage current (see Application Hints).
Connection Diagrams
SOT-23, 5-Lead Small Outline Package (M5)
micro SMD, 5 Bump Package
10014003
Top View
See NS Package Number MF05A
10014046
Note: The actual physical placement of the package marking will vary from part
to part. Package marking contains date code and lot traceability information, and
will vary considerably. Package marking does not correlate to device type.
Top View
See NS Package Numbers TPA05 and TLA05
Pin Descriptions
Name
Pin Number
Function
SOT-23
micro SMD
VIN
1
C3
Input Voltage
GND
2
A1
Common Ground (device substrate)
ON/OFF
3
A3
Logic high enable input
BYPASS
4
B2
Bypass capacitor for low noise operation
VOUT
5
C1
Regulated output voltage
www.national.com
2
LP2985
Ordering Information
TABLE 1. Package Marking and Ordering Information
Output Voltage
(V)
Grade
Order Information
Package Marking
Supplied as:
For output voltages ≤ 2.0V, refer to LP2985LV datasheet.
SOT-23, 5-Lead Small Outline Package (M5)
A
2.5
STD
2.6
A
A
2.7
STD
A
2.8
STD
A
2.9
STD
A
3.0
STD
A
3.1
STD
3.2
STD
A
3.3
STD
3.5
LP2985AIM5-2.5
LAUA
1000 Units on Tape and Reel
LP2985AIM5X-2.5
LAUA
3000 Units on Tape and Reel
LP2985IM5-2.5
LAUB
1000 Units on Tape and Reel
LP2985IM5X-2.5
LAUB
3000 Units on Tape and Reel
LP2985AIM5-2.6
LCEA
1000 Units on Tape and Reel
LP2985AIM5X-2.6
LCEA
3000 Units on Tape and Reel
LP2985AIM5-2.7
LALA
1000 Units on Tape and Reel
LP2985AIM5X-2.7
LALA
3000 Units on Tape and Reel
LP2985IM5-2.7
LALB
1000 Units on Tape and Reel
LP2985IM5X-2.7
LALB
3000 Units on Tape and Reel
LP2985AIM5-2.8
L0KA
1000 Units on Tape and Reel
LP2985AIM5X-2.8
L0KA
3000 Units on Tape and Reel
LP2985IM5-2.8
L0KB
1000 Units on Tape and Reel
LP2985IM5X-2.8
L0KB
3000 Units on Tape and Reel
LP2985AIM5-2.9
LAXA
1000 Units on Tape and Reel
LP2985AIM5X-2.9
LAXA
3000 Units on Tape and Reel
LP2985IM5-2.9
LAXB
1000 Units on Tape and Reel
LP2985IM5X-2.9
LAXB
3000 Units on Tape and Reel
LP2985AIM5-3.0
L0OA
1000 Units on Tape and Reel
LP2985AIM5X-3.0
L0OA
3000 Units on Tape and Reel
LP2985IM5-3.0
L0OB
1000 Units on Tape and Reel
LP2985IM5X-3.0
L0OB
3000 Units on Tape and Reel
LP2985AIM5-3.1
L0PA
1000 Units on Tape and Reel
LP2985AIM5X-3.1
L0PA
3000 Units on Tape and Reel
LP2985IM5-3.1
L0PB
1000 Units on Tape and Reel
LP2985IM5X-3.1
L0PB
3000 Units on Tape and Reel
LP2985IM5-3.2
L0QB
1000 Units on Tape and Reel
LP2985AIM5-3.3
L0RA
1000 Units on Tape and Reel
LP2985AIM5X-3.3
L0RA
3000 Units on Tape and Reel
LP2985IM5-3.3
L0RB
1000 Units on Tape and Reel
LP2985IM5X-3.3
L0RB
3000 Units on Tape and Reel
A
LP2985AIM5-3.5
LAIA
1000 Units on Tape and Reel
STD
LP2985IM5-3.5
LAIB
1000 Units on Tape and Reel
A
3.6
STD
A
3.8
STD
LP2985AIM5-3.6
L0SA
1000 Units on Tape and Reel
LP2985AIM5X-3.6
L0SA
3000 Units on Tape and Reel
LP2985IM5-3.6
L0SB
1000 Units on Tape and Reel
LP2985IM5X-3.6
L0SB
3000 Units on Tape and Reel
LP2985AIM5-3.8
L0YA
1000 Units on Tape and Reel
LP2985AIM5X-3.8
L0YA
3000 Units on Tape and Reel
LP2985IM5-3.8
L0YB
1000 Units on Tape and Reel
LP2985IM5X-3.8
L0YB
3000 Units on Tape and Reel
3
www.national.com
LP2985
Output Voltage
(V)
Grade
A
4.0
STD
A
4.5
STD
A
5.0
STD
A
5.7
STD
A
6.1
STD
Order Information
Package Marking
Supplied as:
LP2985AIM5-4.0
L0TA
1000 Units on Tape and Reel
LP2985AIM5X-4.0
L0TA
3000 Units on Tape and Reel
LP2985IM5-4.0
L0TB
1000 Units on Tape and Reel
LP2985IM5X-4.0
L0TB
3000 Units on Tape and Reel
LP2985AIM5-4.5
LA7A
1000 Units on Tape and Reel
LP2985AIM5X-4.5
LA7A
3000 Units on Tape and Reel
LP2985IM5X-4.5
LA7B
1000 Units on Tape and Reel
LP2985IM5-4.5
LA7B
3000 Units on Tape and Reel
LP2985AIM5-5.0
L0UA
1000 Units on Tape and Reel
LP2985AIM5X-5.0
L0UA
3000 Units on Tape and Reel
LP2985IM5-5.0
L0UB
1000 Units on Tape and Reel
LP2985IM5X-5.0
L0UB
3000 Units on Tape and Reel
LP2985AIM5-5.7
LKTA
1000 Units on Tape and Reel
LP2985AIM5X-5.7
LKTA
3000 Units on Tape and Reel
LP2985IM5-5.7
LKTB
1000 Units on Tape and Reel
LP2985IM5X-5.7
LKTB
3000 Units on Tape and Reel
LP2985AIM5-6.1
LF6A
1000 Units on Tape and Reel
LP2985AIM5X-6.1
LF6A
3000 Units on Tape and Reel
LP2985IM5-6.1
LF6B
1000 Units on Tape and Reel
LP2985IM5X-6.1
LF6B
3000 Units on Tape and Reel
micro SMD, 5 Bump Package (TPA05 - 170 µm ball)
2.5
A
LP2985AITPX-2.5
3000 Units on Tape and Reel
STD
LP2985ITP-2.5
250 Units on Tape and Reel
A
2.6
STD
A
2.7
STD
A
2.8
STD
A
2.9
STD
A
3.0
STD
A
3.3
STD
www.national.com
LP2985AITP-2.6
250 Units on Tape and Reel
LP2985AITPX-2.6
3000 Units on Tape and Reel
LP2985ITP-2.6
250 Units on Tape and Reel
LP2985ITPX-2.6
3000 Units on Tape and Reel
LP2985AITP-2.7
250 Units on Tape and Reel
LP2985AITPX-2.7
3000 Units on Tape and Reel
LP2985ITP-2.7
250 Units on Tape and Reel
LP2985ITPX-2.7
3000 Units on Tape and Reel
LP2985AITP-2.8
250 Units on Tape and Reel
LP2985AITPX-2.8
3000 Units on Tape and Reel
LP2985ITP-2.8
250 Units on Tape and Reel
LP2985ITPX-2.8
3000 Units on Tape and Reel
LP2985AITP-2.9
250 Units on Tape and Reel
LP2985AITPX-2.9
3000 Units on Tape and Reel
LP2985ITP-2.9
250 Units on Tape and Reel
LP2985ITPX-2.9
3000 Units on Tape and Reel
LP2985AITP-3.0
250 Units on Tape and Reel
LP2985AITPX-3.0
3000 Units on Tape and Reel
LP2985ITP-3.0
250 Units on Tape and Reel
LP2985ITPX-3.0
3000 Units on Tape and Reel
LP2985AITP-3.3
250 Units on Tape and Reel
LP2985AITPX-3.3
3000 Units on Tape and Reel
LP2985ITP-3.3
250 Units on Tape and Reel
LP2985ITPX-3.3
3000 Units on Tape and Reel
4
Grade
A
5.0
STD
Order Information
Package Marking
Supplied as:
LP2985AITP-5.0
250 Units on Tape and Reel
LP2985AITPX-5.0
3000 Units on Tape and Reel
LP2985ITP-5.0
250 Units on Tape and Reel
LP2985ITPX-5.0
3000 Units on Tape and Reel
micro SMD, 5 Bump Package (TLA05 - 300 µm ball)
A
3.3
STD
LP2985AITL-3.3
250 Units on Tape and Reel
LP2985AITLX-3.3
3000 Units on Tape and Reel
LP2985ITL-3.3
250 Units on Tape and Reel
LP2985ITLX-3.3
3000 Units on Tape and Reel
For LP2985 Ordering and Availability Information see: http://www.national.com/mpf/LP/LP2985.html#Order
5
www.national.com
LP2985
Output Voltage
(V)
LP2985
Power Dissipation (Note 3)
Input Supply Voltage (Survival)
Input Supply Voltage (Operating)
Shutdown Input Voltage (Survival)
Output Voltage (Survival, (Note 4))
IOUT (Survival)
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Storage Temperature Range
Operating Junction Temperature
Range
Lead Temp. (Soldering, 5 sec.)
ESD Rating (Note 2)
−65°C to +150°C
−40°C to +125°C
260°C
2 kV
Internally Limited
−0.3V to +16V
2.5V to +16V
−0.3V to +16V
−0.3V to +9V
Short Circuit
Protected
−0.3V to +16V
Input-Output Voltage (Survival,
(Note 5))
Electrical Characteristics
(Note 10)
Limits in standard typeface are for TJ = 25°C. and limits in boldface type apply over the full operating temperature range. Unless
otherwise specified: VIN = VO(NOM) + 1V, IL = 1 mA, CIN = 1 µF, COUT = 4.7 µF, VON/OFF = 2V.
Symbol
ΔVO
LP2985AI-X.X
(Note 6)
LP2985I-X.X
(Note 6)
Min
Max
Min
Max
IL = 1 mA
−1.0
1.0
−1.5
1.5
1 mA ≤ IL ≤ 50 mA
−1.5
1.5
−2.5
2.5
−2.5
2.5
−3.5
3.5
−2.5
2.5
−3.0
3.0
3.5
−4.0
Parameter
Output Voltage
Tolerance
Conditions
Typ
1 mA ≤ IL ≤ 150 mA
−3.5
Output Voltage
VO(NOM)+1V ≤ VIN ≤ 16V
0.007
Line Regulation
VIN–VO
Dropout Voltage
(Note 7)
IL = 0
1
IL = 1 mA
7
IL = 10 mA
40
IL = 50 mA
IGND
Ground Pin Current
120
IL = 150 mA
280
IL = 0
65
IL = 1 mA
VON/OFF
ION/OFF
75
IL = 10 mA
120
IL = 50 mA
350
IL = 150 mA
850
VON/OFF < 0.3V
0.01
0.032
0.032
3
3
5
5
10
10
15
15
60
60
90
90
150
150
225
225
350
350
575
575
95
95
125
125
110
110
170
170
220
220
400
400
600
600
1000
1000
1500
1500
2500
2500
0.8
0.8
VON/OFF < 0.15V
0.05
ON/OFF Input Voltage
(Note 8)
High = O/P ON
1.4
Low = O/P OFF
0.55
0.15
0.15
ON/OFF Input Current
VON/OFF = 0
0.01
−2
−2
5
15
15
VON/OFF = 5V
www.national.com
0.014
6
2
%VNOM
4.0
0.014
1.6
Units
%/V
mV
µA
2
1.6
V
µA
en
Parameter
Output Noise
Voltage (RMS)
Conditions
Typ
BW = 300 Hz to 50 kHz,
COUT = 10 µF
LP2985I-X.X
(Note 6)
Min
Min
Max
Units
Max
30
µV
45
dB
400
mA
350
mA
CBYPASS = 10 nF
Ripple Rejection
f = 1 kHz, CBYPASS = 10 nF
COUT = 10 µF
IO(SC)
Short Circuit Current
RL = 0 (Steady State)
(Note 9)
IO(PK)
Peak Output Current
VOUT ≥ Vo(NOM) −5%
Note 1: “Absolute Maximum Ratings” indicate limits beyond which damage to the component may occur. Electrical specifications do not apply when operating
the device outside of its rated operating conditions.
Note 2: The ESD rating of pins 3 and 4 for the SOT-23 package, or pins 5 and 2 for the micro SMD package, is 1 kV.
Note 3: The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(MAX), the junction-to-ambient thermal resistance, θJA, and the ambient temperature, TA. The maximum allowable power dissipation at any ambient temperture is calculated using:
Where the value of θJ-A for the SOT-23 package is 220°C/W in a typical PC board mounting and the micro SMD package is 225°C/W. Exceeding the maximum
allowable dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown.
Note 4: For 12V option, output voltage survival: -0.3 to +16V. If used in a dual-supply system where the regulator load is returned to a negative supply, the LP2985
output must be diode-clamped to ground.
Note 5: The output PNP structure contains a diode between the VIN to VOUT terminals that is normally reverse-biased. Reversing the polarity from VIN to VOUT
will turn on this diode.
Note 6: Limits are 100% production tested at 25°C. Limits over the operating temperature range are guaranteed through correlation using Statistical Quality
Control (SQC) methods. The limits are used to calculate National's Average Outgoing Quality Level (AOQL).
Note 7: Dropout voltage is defined as the input to output differential at which the output voltage drops 100 mV below the value measured with a 1V differential.
Note 8: The ON/OFF input must be properly driven to prevent possible misoperation. For details, refer to Application Hints.
Note 9: The LP2985 has foldback current limiting which allows a high peak current when VOUT > 0.5V, and then reduces the maximum output current as VOUT is
forced to ground (see Typical Performance Characteristics curves).
Note 10: Exposing the micro SMD device to direct sunlight will cause misoperation. See Application Hints for additional information.
7
www.national.com
LP2985
Symbol
LP2985AI-X.X
(Note 6)
LP2985
Typical Performance Characteristics
Unless otherwise specified: CIN = 1µF, COUT = 4.7µF, VIN = VOUT
(NOM) +1, TA = 25°C, ON/OFF pin is tied to VIN.
VOUT vs Temperature
Short-Circuit Current
10014009
10014008
Short-Circuit Current
Short Circuit Current vs Output Voltage
10014010
10014011
Ripple Rejection
Ripple Rejection
10014013
www.national.com
10014014
8
LP2985
Ripple Rejection
Ripple Rejection
10014015
10014016
Ripple Rejection
Ripple Rejection
10014017
10014018
Ripple Rejection
Ripple Rejection
10014019
10014023
9
www.national.com
LP2985
Ripple Rejection
Output Impedance vs Frequency
10014020
10014022
Output Impedance vs Frequency
Output Noise Density
10014024
10014021
Output Noise Density
Ground Pin vs Load Current
10014025
www.national.com
10014026
10
LP2985
Dropout Voltage vs Temperature
Input Current vs Pin
10014027
10014029
GND Pin Current vs Temperature
Instantaneous Short Circuit Current
10014031
10014030
Load Transient Response
Load Transient Response
10014032
10014033
11
www.national.com
LP2985
Load Transient Response
Line Transient Response
10014035
10014034
Line Transient Response
Line Transient Response
10014036
10014037
Line Transient Response
Turn-On Time
10014038
www.national.com
10014039
12
LP2985
Turn-On Time
Turn-On Time
10014041
10014040
Turn-On Time
10014042
13
www.national.com
LP2985
Application Hints
EXTERNAL CAPACITORS
Like any low-dropout regulator, the LP2985 requires external
capacitors for regulator stability. These capacitors must be
correctly selected for good performance.
capacitors can exhibit large changes in capacitance with temperature (see next section, Capacitor Characteristics).
The output capacitor must be located not more than 1 cm from
the output pin and returned to a clean analog ground.
Input Capacitor
An input capacitor whose capacitance is ≥ 1 µF is required
between the LP2985 input and ground (the amount of capacitance may be increased without limit).
This capacitor must be located a distance of not more than 1
cm from the input pin and returned to a clean analog ground.
Any good quality ceramic, tantalum, or film capacitor may be
used at the input.
Important: Tantalum capacitors can suffer catastrophic failure due to surge current when connected to a low-impedance
source of power (like a battery or very large capacitor). If a
Tantalum capacitor is used at the input, it must be guaranteed
by the manufacturer to have a surge current rating sufficient
for the application.
There are no requirements for ESR on the input capacitor, but
tolerance and temperature coefficient must be considered
when selecting the capacitor to ensure the capacitance will
be ≥ 1 µF over the entire operating temperature range.
Noise Bypass Capacitor
Connecting a 10 nF capacitor to the Bypass pin significantly
reduces noise on the regulator output. It should be noted that
the capacitor is connected directly to a high-impedance circuit
in the bandgap reference.
Because this circuit has only a few microamperes flowing in
it, any significant loading on this node will cause a change in
the regulated output voltage. For this reason, DC leakage
current through the noise bypass capacitor must never exceed 100 nA, and should be kept as low as possible for best
output voltage accuracy.
The types of capacitors best suited for the noise bypass capacitor are ceramic and film. High-quality ceramic capacitors
with either NPO or COG dielectric typically have very low
leakage. 10 nF polypropolene and polycarbonate film capacitors are available in small surface-mount packages and typically have extremely low leakage current.
CAPACITOR CHARACTERISTICS
The LP2985 was designed to work with ceramic capacitors
on the output to take advantage of the benefits they offer: for
capacitance values in the 2.2 µF to 4.7 µF range, ceramics
are the least expensive and also have the lowest ESR values
(which makes them best for eliminating high-frequency
noise). The ESR of a typical 2.2 µF ceramic capacitor is in the
range of 10 mΩ to 20 mΩ, which easily meets the ESR limits
required for stability by the LP2985.
One disadvantage of ceramic capacitors is that their capacitance can vary with temperature. Most large value ceramic
capacitors (≥ 2.2 µF) are manufactured with the Z5U or Y5V
temperature characteristic, which results in the capacitance
dropping by more than 50% as the temperature goes from 25°
C to 85°C.
This could cause problems if a 2.2 µF capacitor were used on
the output since it will drop down to approximately 1 µF at high
ambient temperatures (which could cause the LM2985 to oscillate). If Z5U or Y5V capacitors are used on the output, a
minimum capacitance value of 4.7 µF must be observed.
A better choice for temperature coefficient in ceramic capacitors is X7R, which holds the capacitance within ±15%. Unfortunately, the larger values of capacitance are not offered
by all manufacturers in the X7R dielectric.
Output Capacitor
The LP2985 is designed specifically to work with ceramic output capacitors, utilizing circuitry which allows the regulator to
be stable across the entire range of output current with an
output capacitor whose ESR is as low as 5 mΩ. It may also
be possible to use Tantalum or film capacitors at the output,
but these are not as attractive for reasons of size and cost
(see next section Capacitor Characteristics).
The output capacitor must meet the requirement for minimum
amount of capacitance and also have an ESR (equivalent series resistance) value which is within the stable range. Curves
are provided which show the stable ESR range as a function
of load current (see ESR graph below).
Tantalum
Tantalum capacitors are less desirable than ceramics for use
as output capacitors because they are more expensive when
comparing equivalent capacitance and voltage ratings in the
1 µF to 4.7 µF range.
Another important consideration is that Tantalum capacitors
have higher ESR values than equivalent size ceramics. This
means that while it may be possible to find a Tantalum capacitor with an ESR value within the stable range, it would
have to be larger in capacitance (which means bigger and
more costly) than a ceramic capacitor with the same ESR
value.
It should also be noted that the ESR of a typical Tantalum will
increase about 2:1 as the temperature goes from 25°C down
to −40°C, so some guard band must be allowed.
10014007
Important: The output capacitor must maintain its ESR within
the stable region over the full operating temperature range of
the application to assure stability.
The LP2985 requires a minimum of 2.2 µF on the output (output capacitor size can be increased without limit).
It is important to remember that capacitor tolerance and variation with temperature must be taken into consideration when
selecting an output capacitor so that the minimum required
amount of output capacitance is provided over the full operating temperature range. It should be noted that ceramic
www.national.com
14
10014055
REVERSE INPUT-OUTPUT VOLTAGE
The PNP power transistor used as the pass element in the
LP2985 has an inherent diode connected between the regulator output and input. During normal operation (where the
input voltage is higher than the output) this diode is reversebiased.
FIGURE 2. Reverse Current Protection
MICRO SMD MOUNTING
The micro SMD package requires specific mounting techniques which are detailed in National Semiconductor Application Note # 1112. Referring to the section Surface Mount
Technology (SMT) Assembly Considerations, it should be
noted that the pad style which must be used with the 5-pin
package is the NSMD (non-solder mask defined) type.
For best results during assembly, alignment ordinals on the
PC board may be used to facilitate placement of the micro
SMD device.
MICRO SMD LIGHT SENSITIVITY
Exposing the micro SMD device to direct sunlight will cause
misoperation of the device. Light sources such as Halogen
lamps can also affect electrical performance if brought near
to the device.
The wavelenghts which have the most detrimental effect are
reds and infra-reds, which means that the fluorescent lighting
used inside most buildings has very little effect on performance. A micro SMD test board was brought to within 1 cm
of a fluorescent desk lamp and the effect on the regulated
output voltage was negligible, showing a deviation of less
than 0.1% from nominal.
10014054
FIGURE 1. Reverse Current Path
However, if the output is pulled above the input, this diode will
turn ON and current will flow into the regulator output. In such
cases, a parasitic SCR can latch which will allow a high current to flow into VIN (and out the ground pin), which can
damage the part.
In any application where the output may be pulled above the
input, an external Schottky diode must be connected from
15
www.national.com
LP2985
VIN to VOUT (cathode on VIN, anode on VOUT), to limit the reverse voltage across the LP2985 to 0.3V (see Absolute Maximum Ratings).
On/Off Input Operation
The LP2985 is shut off by driving the ON/OFF input low, and
turned on by pulling it high. If this feature is not to be used,
the ON/OFF input should be tied to VIN to keep the regulator
output on at all times.
To assure proper operation, the signal source used to drive
the ON/OFF input must be able to swing above and below the
specified turn-on/turn-off voltage thresholds listed in the Electrical Characteristics section under VON/OFF. To prevent misoperation, the turn-on (and turn-off) voltage signals applied to
the ON/OFF input must have a slew rate which is
≥ 40 mV/µs.
Caution: the regulator output voltage can not be guaranteed
if a slow-moving AC (or DC) signal is applied that is in the
range between the specified turn-on and turn-off voltages listed under the electrical specification VON/OFF (see Electrical
Characteristics).
LP2985
Physical Dimensions inches (millimeters) unless otherwise noted
SOT-23, 5-Lead Small Outline Package (M5)
NS Package Number MF05A.
www.national.com
16
LP2985
NOTES: UNLESS OTHERWISE SPECIFIED
1. EPOXY COATING
2. RECOMMEND NON-SOLDER MASK DEFINED LANDING PAD.
3. PIN 1 IS ESTABLISHED BY LOWER LEFT CORNER WITH RESPECT TO TEXT ORIENTATION. REMAINING PINS ARE NUMBERED COUNTER CLOCKWISE.
4. XXX IN DRAWING NUMBER REPRESENTS PACKAGE SIZE VARIATION WHERE X1 IS PACKAGE WIDTH, X2 IS PACKAGE LENGTH AND X3 IS PACKAGE HEIGHT.
5.NO JEDEC REGISTRATION AS OF AUG.1999.
micro SMD, 5 Bump, Package (TPA05 - 170 µm ball)
NS Package Number TPA05
The dimensions for X1, X2 and X3 are as given:
X1 = 0.930 +/− 0.030mm
X2 = 1.107 +/− 0.030mm
X3 = 0.500 +/− 0.075mm
17
www.national.com
LP2985
NOTES: UNLESS OTHERWISE SPECIFIED
1. EPOXY COATING
2. RECOMMEND NON-SOLDER MASK DEFINED LANDING PAD.
3. PIN 1 IS ESTABLISHED BY LOWER LEFT CORNER WITH RESPECT TO TEXT ORIENTATION. REMAINING PINS ARE NUMBERED COUNTER CLOCKWISE.
4. XXX IN DRAWING NUMBER REPRESENTS PACKAGE SIZE VARIATION WHERE X1 IS PACKAGE WIDTH, X2 IS PACKAGE LENGTH AND X3 IS PACKAGE HEIGHT.
5.NO JEDEC REGISTRATION AS OF AUG.1999.
micro SMD, 5 Bump, Package (TLA05 - 300 µm ball)
NS Package Number TLA05
The dimensions for X1, X2 and X3 are as given:
X1 = 1.031 +/− 0.030mm
X2 = 1.412 +/− 0.030mm
X3 = 0.600 +/− 0.075mm
www.national.com
18
LP2985
Notes
19
www.national.com
LP2985 Micropower 150 mA Low-Noise Ultra Low-Dropout Regulator in SOT-23 and micro SMD
Packages
Notes
For more National Semiconductor product information and proven design tools, visit the following Web sites at:
www.national.com
Products
Design Support
Amplifiers
www.national.com/amplifiers
WEBENCH® Tools
www.national.com/webench
Audio
www.national.com/audio
App Notes
www.national.com/appnotes
Clock and Timing
www.national.com/timing
Reference Designs
www.national.com/refdesigns
Data Converters
www.national.com/adc
Samples
www.national.com/samples
Interface
www.national.com/interface
Eval Boards
www.national.com/evalboards
LVDS
www.national.com/lvds
Packaging
www.national.com/packaging
Power Management
www.national.com/power
Green Compliance
www.national.com/quality/green
Switching Regulators
www.national.com/switchers
Distributors
www.national.com/contacts
LDOs
www.national.com/ldo
Quality and Reliability
www.national.com/quality
LED Lighting
www.national.com/led
Feedback/Support
www.national.com/feedback
Voltage References
www.national.com/vref
Design Made Easy
www.national.com/easy
www.national.com/powerwise
Applications & Markets
www.national.com/solutions
Mil/Aero
www.national.com/milaero
PowerWise® Solutions
Serial Digital Interface (SDI) www.national.com/sdi
Temperature Sensors
www.national.com/tempsensors SolarMagic™
www.national.com/solarmagic
PLL/VCO
www.national.com/wireless
www.national.com/training
PowerWise® Design
University
THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION
(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY
OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO
SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,
IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS
DOCUMENT.
TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT
NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL
PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR
APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND
APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE
NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.
EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO
LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE
AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR
PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY
RIGHT.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and
whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected
to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform
can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.
National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other
brand or product names may be trademarks or registered trademarks of their respective holders.
Copyright© 2011 National Semiconductor Corporation
For the most current product information visit us at www.national.com
National Semiconductor
Americas Technical
Support Center
Email: [email protected]
Tel: 1-800-272-9959
www.national.com
National Semiconductor Europe
Technical Support Center
Email: [email protected]
National Semiconductor Asia
Pacific Technical Support Center
Email: [email protected]
National Semiconductor Japan
Technical Support Center
Email: [email protected]
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Communications and Telecom www.ti.com/communications
Amplifiers
amplifier.ti.com
Computers and Peripherals
www.ti.com/computers
Data Converters
dataconverter.ti.com
Consumer Electronics
www.ti.com/consumer-apps
DLP® Products
www.dlp.com
Energy and Lighting
www.ti.com/energy
DSP
dsp.ti.com
Industrial
www.ti.com/industrial
Clocks and Timers
www.ti.com/clocks
Medical
www.ti.com/medical
Interface
interface.ti.com
Security
www.ti.com/security
Logic
logic.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and Automotive www.ti.com/automotive
Microcontrollers
microcontroller.ti.com
Video and Imaging
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
www.ti.com/video
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
Similar pages