TI1 LM1117ILDX-ADJ 800ma low-dropout linear regulator Datasheet

LM1117/LM1117I
800mA Low-Dropout Linear Regulator
General Description
Features
The LM1117 is a series of low dropout voltage regulators with
a dropout of 1.2V at 800mA of load current. It has the same
pin-out as National Semiconductor's industry standard
LM317.
The LM1117 is available in an adjustable version, which can
set the output voltage from 1.25V to 13.8V with only two external resistors. In addition, it is also available in five fixed
voltages, 1.8V, 2.5V, 2.85V, 3.3V, and 5V.
The LM1117 offers current limiting and thermal shutdown. Its
circuit includes a zener trimmed bandgap reference to assure
output voltage accuracy to within ±1%.
The LM1117 series is available in LLP, TO-263, SOT-223,
TO-220, and TO-252 D-PAK packages. A minimum of 10µF
tantalum capacitor is required at the output to improve the
transient response and stability.
● Available in 1.8V, 2.5V, 2.85V, 3.3V, 5V, and Adjustable
●
●
●
●
●
●
Versions
Space Saving SOT-223 and LLP Packages
Current Limiting and Thermal Protection
Output Current
800mA
Line Regulation
0.2% (Max)
Load Regulation
0.4% (Max)
Temperature Range
0°C to 125°C
— LM1117
−40°C to 125°C
— LM1117I
Applications
●
●
●
●
●
2.85V Model for SCSI-2 Active Termination
Post Regulator for Switching DC/DC Converter
High Efficiency Linear Regulators
Battery Charger
Battery Powered Instrumentation
Typical Application
Active Terminator for SCSI-2 Bus
10091905
Fixed Output Regulator
10091928
PRODUCTION DATA information is current as of
publication date. Products conform to specifications per
the terms of the Texas Instruments standard warranty.
Production processing does not necessarily include
testing of all parameters.
100919 SNOS412L
Copyright © 1999-2012, Texas Instruments Incorporated
LM1117/LM1117I
Ordering Information
Package
Temperature Range
Part Number
Packaging Marking
Transport Media
NSC
Drawing
3-lead SOT-223
0°C to +125°C
LM1117MPX-ADJ
N03A
Tape and Reel
MP04A
LM1117MPX-2.5
N13A
Tape and Reel
LM1117MPX-2.85
N04A
Tape and Reel
LM1117MPX-3.3
N05A
Tape and Reel
−40°C to +125°C
3-lead TO-220
3-lead TO-252
0°C to +125°C
0°C to +125°C
−40°C to +125°C
8-lead LLP
0°C to +125°C
−40°C to 125°C
TO-263
2
0°C to +125°C
LM1117MPX-5.0
N06A
Tape and Reel
LM1117IMPX-ADJ
N03B
Tape and Reel
LM1117IMPX-3.3
N05B
Tape and Reel
LM1117IMPX-5.0
N06B
Tape and Reel
LM1117T-ADJ
LM1117T-ADJ
Rails
LM1117T-1.8
LM1117T-1.8
Rails
LM1117T-2.5
LM1117T-2.5
Rails
LM1117T-3.3
LM1117T-3.3
Rails
LM1117T-5.0
LM1117T-5.0
Rails
LM1117DTX-ADJ
LM1117DT-ADJ
Tape and Reel
LM1117DTX-1.8
LM1117DT-1.8
Tape and Reel
LM1117DTX-2.5
LM1117DT-2.5
Tape and Reel
LM1117DTX-3.3
LM1117DT-3.3
Tape and Reel
LM1117DTX-5.0
LM1117DT-5.0
Tape and Reel
LM1117IDTX-ADJ
LM1117IDT-ADJ
Tape and Reel
LM1117IDTX-3.3
LM1117IDT-3.3
Tape and Reel
LM1117IDTX-5.0
LM1117IDT-5.0
Tape and Reel
LM1117LDX-ADJ
1117ADJ
Tape and Reel
LM1117LDX-1.8
1117-18
Tape and Reel
LM1117LDX-5.0
1117-50
Tape and Reel
LM1117ILDX-ADJ
1117IAD
Tape and Reel
LM1117ILDX-3.3
1117I33
Tape and Reel
LM1117ILDX-5.0
1117I50
Tape and Reel
LM1117SX-ADJ
LM1117SADJ
Tape and Reel
LM1117SX-3.3
LM1117S3.3
Tape and Reel
LM1117SX-5.0
LM1117S5.0
Tape and Reel
T03B
TD03B
LDC08A
TS3B
Copyright © 1999-2012, Texas Instruments Incorporated
LM1117/LM1117I
Block Diagram
10091901
Connection Diagrams
SOT-223
10091904
Top View
TO-220
10091902
Top View
TO-252
10091938
Top View
Copyright © 1999-2012, Texas Instruments Incorporated
3
LM1117/LM1117I
TO-263
10091944
Top View
10091945
Side View
LLP
10091946
When using the LLP package
Pins 2, 3 & 4 must be connected together and
Pins 5, 6 & 7 must be connected together
Top View
4
Copyright © 1999-2012, Texas Instruments Incorporated
LM1117/LM1117I
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for
availability and specifications.
Maximum Input Voltage (VIN to GND)
Power Dissipation (Note 2)
Junction Temperature (TJ)
(Note 2)
Storage Temperature Range
Lead Temperature
TO-220 (T) Package
SOT-223 (IMP) Package
ESD Tolerance (Note 3)
Operating Ratings
20V
Internally Limited
150°C
-65°C to 150°C
260°C, 10 sec
260°C, 4 sec
2000V
(Note 1)
Input Voltage (VIN to GND)
Junction Temperature Range (TJ)(Note 2)
LM1117
LM1117I
15V
0°C to 125°C
−40°C to 125°C
LM1117 Electrical Characteristics
Typicals and limits appearing in normal type apply for TJ = 25°C. Limits appearing in Boldface type apply over the entire junction
temperature range for operation, 0°C to 125°C.
Symbol
VREF
Parameter
Reference Voltage
Conditions
LM1117-ADJ
IOUT = 10mA, VIN-VOUT = 2V, TJ = 25°C
10mA ≤ IOUT ≤ 800mA, 1.4V ≤ VIN-VOUT ≤
10V
VOUT
Output Voltage
LM1117-1.8
IOUT = 10mA, VIN = 3.8V, TJ = 25°C
0 ≤ IOUT ≤ 800mA, 3.2V ≤ VIN ≤ 10V
LM1117-2.5
IOUT = 10mA, VIN = 4.5V, TJ = 25°C
0 ≤ IOUT ≤ 800mA, 3.9V ≤ VIN ≤ 10V
LM1117-2.85
IOUT = 10mA, VIN = 4.85V, TJ = 25°C
0 ≤ IOUT ≤ 800mA, 4.25V ≤ VIN ≤ 10V
0 ≤ IOUT ≤ 500mA, VIN = 4.10V
LM1117-3.3
IOUT = 10mA, VIN = 5V TJ = 25°C
0 ≤ IOUT ≤ 800mA, 4.75V≤ VIN ≤ 10V
LM1117-5.0
IOUT = 10mA, VIN = 7V, TJ = 25°C
0 ≤ IOUT ≤ 800mA, 6.5V ≤ VIN ≤ 12V
Copyright © 1999-2012, Texas Instruments Incorporated
Min
(Note 5)
Typ
(Note 4)
Max
(Note 5)
Units
1.238
1.225
1.250
1.250
1.262
1.270
V
V
1.782
1.746
1.800
1.800
1.818
1.854
V
V
2.475
2.450
2.500
2.500
2.525
2.550
V
V
2.820
2.790
2.790
2.850
2.850
2.850
2.880
2.910
2.910
V
V
V
3.267
3.235
3.300
3.300
3.333
3.365
V
V
4.950
4.900
5.000
5.000
5.050
5.100
V
V
5
LM1117/LM1117I
Symbol
ΔVOUT
Typ
(Note 4)
Max
(Note 5)
Units
0.035
0.2
%
1
6
mV
1
6
mV
1
6
mV
1
6
mV
1
10
mV
0.2
0.4
%
1
10
mV
1
10
mV
1
10
mV
1
10
mV
1
15
mV
IOUT = 100mA
1.10
1.20
V
IOUT = 500mA
1.15
1.25
V
Parameter
Line Regulation
(Note 6)
Conditions
Min
(Note 5)
LM1117-ADJ
IOUT = 10mA, 1.5V ≤ VIN-VOUT ≤ 13.75V
LM1117-1.8
IOUT = 0mA, 3.2V ≤ VIN ≤ 10V
LM1117-2.5
IOUT = 0mA, 3.9V ≤ VIN ≤ 10V
LM1117-2.85
IOUT = 0mA, 4.25V ≤ VIN ≤ 10V
LM1117-3.3
IOUT = 0mA, 4.75V ≤ VIN ≤ 15V
LM1117-5.0
IOUT = 0mA, 6.5V ≤ VIN ≤ 15V
ΔVOUT
Load Regulation
(Note 6)
LM1117-ADJ
VIN-VOUT = 3V, 10 ≤ IOUT ≤ 800mA
LM1117-1.8
VIN = 3.2V, 0 ≤ IOUT ≤ 800mA
LM1117-2.5
VIN = 3.9V, 0 ≤ IOUT ≤ 800mA
LM1117-2.85
VIN = 4.25V, 0 ≤ IOUT ≤ 800mA
LM1117-3.3
VIN = 4.75V, 0 ≤ IOUT ≤ 800mA
LM1117-5.0
VIN = 6.5V, 0 ≤ IOUT ≤ 800mA
VIN-V OUT
Dropout Voltage
(Note 7)
IOUT = 800mA
ILIMIT
Current Limit
VIN-VOUT = 5V, TJ = 25°C
800
Minimum Load Current LM1117-ADJ
(Note 8)
VIN = 15V
Quiescent Current
LM1117-1.8
1.20
1.30
V
1200
1500
mA
1.7
5
mA
5
10
mA
5
10
mA
5
10
mA
5
10
mA
5
10
mA
0.01
0.1
%/W
VIN ≤ 15V
LM1117-2.5
VIN ≤ 15V
LM1117-2.85
VIN ≤ 10V
LM1117-3.3
VIN ≤ 15V
LM1117-5.0
VIN ≤ 15V
Thermal Regulation
TA = 25°C, 30ms Pulse
Ripple Regulation
fRIPPLE =1 20Hz, VIN-VOUT = 3V VRIPPLE =
1VPP
Adjust Pin Current
Adjust Pin Current
Change
6
75
dB
60
120
μA
0.2
5
μA
10 ≤ IOUT≤ 800mA,
1.4V ≤ VIN-VOUT ≤ 10V
Temperature Stability
Long Term Stability
60
TA = 125°C, 1000Hrs
0.5
%
0.3
%
Copyright © 1999-2012, Texas Instruments Incorporated
LM1117/LM1117I
Symbol
Parameter
Conditions
Min
(Note 5)
Typ
(Note 4)
Max
(Note 5)
Units
RMS Output Noise
(% of VOUT), 10Hz ≤ f ≤10kHz
0.003
%
Thermal Resistance
Junction-to-Case
3-Lead SOT-223
15.0
°C/W
3-Lead TO-220
3.0
°C/W
3-Lead TO-252
10
°C/W
3-Lead SOT-223 (No heat sink)
136
°C/W
3-Lead TO-220 (No heat sink)
79
°C/W
3-Lead TO-252 (Note 9) (No heat sink)
92
°C/W
3-Lead TO-263
55
°C/W
8-Lead LLP(Note 10)
40
°C/W
Thermal Resistance
Junction-to-Ambient
(No air flow)
LM1117I Electrical Characteristics
Typicals and limits appearing in normal type apply for TJ = 25°C. Limits appearing in Boldface type apply over the entire junction
temperature range for operation, −40°C to 125°C.
Symbol
VREF
Parameter
Reference Voltage
Conditions
LM1117I-ADJ
IOUT = 10mA, VIN-VOUT = 2V, TJ = 25°C
10mA ≤ IOUT ≤ 800mA, 1.4V ≤ VIN-VOUT ≤
10V
VOUT
Output Voltage
LM1117I-3.3
IOUT = 10mA, VIN = 5V, TJ = 25°C
0 ≤ IOUT ≤ 800mA, 4.75V ≤ VIN ≤ 10V
LM1117I-5.0
IOUT = 10mA, VIN = 7V, TJ = 25°C
0 ≤ IOUT ≤ 800mA, 6.5V ≤ VIN ≤ 12V
ΔVOUT
Line Regulation
(Note 6)
Min
(Note 5)
Typ
(Note 4)
Max
(Note 5)
Units
1.238
1.200
1.250
1.250
1.262
1.290
V
V
3.267
3.168
3.300
3.300
3.333
3.432
V
V
4.950
4.800
5.000
5.000
5.050
5.200
V
V
0.035
0.3
%
1
10
mV
1
15
mV
0.2
0.5
%
1
15
mV
LM1117I-ADJ
IOUT = 10mA, 1.5V ≤ VIN-VOUT ≤ 13.75V
LM1117I-3.3
IOUT = 0mA, 4.75V ≤ VIN ≤ 15V
LM1117I-5.0
IOUT = 0mA, 6.5V ≤ VIN ≤ 15V
ΔVOUT
Load Regulation
(Note 6)
LM1117I-ADJ
VIN-VOUT = 3V, 10 ≤ IOUT ≤ 800mA
LM1117I-3.3
VIN = 4.75V, 0 ≤ IOUT ≤ 800mA
LM1117I-5.0
VIN = 6.5V, 0 ≤ IOUT ≤ 800mA
VIN-V OUT
ILIMIT
Dropout Voltage
(Note 7)
Current Limit
1
20
mV
IOUT = 100mA
1.10
1.30
V
IOUT = 500mA
1.15
1.35
V
IOUT = 800mA
1.20
1.40
V
1200
1500
mA
1.7
5
mA
5
15
mA
VIN-VOUT = 5V, TJ = 25°C
Minimum Load Current LM1117I-ADJ
(Note 8)
VIN = 15V
Quiescent Current
800
LM1117I-3.3
VIN ≤ 15V
LM1117I-5.0
VIN ≤ 15V
Thermal Regulation
TA = 25°C, 30ms Pulse
Copyright © 1999-2012, Texas Instruments Incorporated
5
15
mA
0.01
0.1
%/W
7
LM1117/LM1117I
Symbol
Parameter
Ripple Regulation
Conditions
Min
(Note 5)
Typ
(Note 4)
60
75
fRIPPLE =1 20Hz, VIN-VOUT = 3V VRIPPLE =
1VPP
Adjust Pin Current
Adjust Pin Current
Change
Max
(Note 5)
dB
60
120
μA
0.2
10
μA
10 ≤ IOUT≤ 800mA,
1.4V ≤ VIN-VOUT ≤ 10V
Temperature Stability
Units
0.5
%
0.3
%
(% of VOUT), 10Hz ≤ f ≤10kHz
0.003
%
Thermal Resistance
Junction-to-Case
3-Lead SOT-223
15.0
°C/W
3-Lead TO-252
10
°C/W
Thermal Resistance
Junction-to-Ambient
No air flow)
3-Lead SOT-223 (No heat sink)
136
°C/W
3-Lead TO-252 (No heat sink)(Note 9)
92
°C/W
8-Lead LLP(Note 10)
40
°C/W
Long Term Stability
TA = 125°C, 1000Hrs
RMS Output Noise
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics.
Note 2: The maximum power dissipation is a function of TJ(max) , θJA, and TA. The maximum allowable power dissipation at any ambient temperature is
PD = (TJ(max)–TA)/θJA. All numbers apply for packages soldered directly into a PC board.
Note 3: For testing purposes, ESD was applied using human body model, 1.5kΩ in series with 100pF.
Note 4: Typical Values represent the most likely parametric norm.
Note 5: All limits are guaranteed by testing or statistical analysis.
Note 6: Load and line regulation are measured at constant junction room temperature.
Note 7: The dropout voltage is the input/output differential at which the circuit ceases to regulate against further reduction in input voltage. It is measured when
the output voltage has dropped 100mV from the nominal value obtained at VIN = VOUT +1.5V.
Note 8: The minimum output current required to maintain regulation.
Note 9: Minimum pad size of 0.038in2
Note 10: Thermal Performance for the LLP was obtained using JESD51-7 board with six vias and an ambient temperature of 22°C. For information about improved
thermal performance and power dissipation for the LLP, refer to Application Note AN-1187.
8
Copyright © 1999-2012, Texas Instruments Incorporated
LM1117/LM1117I
Typical Performance Characteristics
Dropout Voltage (VIN-V OUT)
Short-Circuit Current
10091923
10091922
Load Regulation
LM1117-ADJ Ripple Rejection
10091943
LM1117-ADJ Ripple Rejection vs. Current
10091907
Copyright © 1999-2012, Texas Instruments Incorporated
10091906
Temperature Stability
10091925
9
LM1117/LM1117I
Adjust Pin Current
LM1117-2.85 Load Transient Response
10091926
LM1117-5.0 Load Transient Response
10091909
10091908
LM1117-2.85 Line Transient Response
10091910
LM1117-5.0 Line Transient Response
10091911
10
Copyright © 1999-2012, Texas Instruments Incorporated
LM1117/LM1117I
Application Note
1.0 EXTERNAL CAPACITORS/STABILITY
1.1 Input Bypass Capacitor
An input capacitor is recommended. A 10µF tantalum on the input is a suitable input bypassing for almost all applications.
1.2 Adjust Terminal Bypass Capacitor
The adjust terminal can be bypassed to ground with a bypass capacitor (CADJ) to improve ripple rejection. This bypass capacitor
prevents ripple from being amplified as the output voltage is increased. At any ripple frequency, the impedance of the CADJ should
be less than R1 to prevent the ripple from being amplified:
1/(2π*fRIPPLE*CADJ) < R1
The R1 is the resistor between the output and the adjust pin. Its value is normally in the range of 100-200Ω. For example, with R1
= 124Ω and fRIPPLE = 120Hz, the CADJ should be > 11µF.
1.3 Output Capacitor
The output capacitor is critical in maintaining regulator stability, and must meet the required conditions for both minimum amount
of capacitance and ESR (Equivalent Series Resistance). The minimum output capacitance required by the LM1117 is 10µF, if a
tantalum capacitor is used. Any increase of the output capacitance will merely improve the loop stability and transient response.
The ESR of the output capacitor should range between 0.3Ω - 22Ω. In the case of the adjustable regulator, when the CADJ is used,
a larger output capacitance (22µf tantalum) is required.
2.0 OUTPUT VOLTAGE
The LM1117 adjustable version develops a 1.25V reference voltage, VREF, between the output and the adjust terminal. As shown
in Figure 1, this voltage is applied across resistor R1 to generate a constant current I1. The current IADJ from the adjust terminal
could introduce error to the output. But since it is very small (60µA) compared with the I1 and very constant with line and load
changes, the error can be ignored. The constant current I1 then flows through the output set resistor R2 and sets the output voltage
to the desired level.
For fixed voltage devices, R1 and R2 are integrated inside the devices.
10091917
FIGURE 1. Basic Adjustable Regulator
3.0 LOAD REGULATION
The LM1117 regulates the voltage that appears between its output and ground pins, or between its output and adjust pins. In some
cases, line resistances can introduce errors to the voltage across the load. To obtain the best load regulation, a few precautions
are needed.
Figure 2, shows a typical application using a fixed output regulator. The Rt1 and Rt2 are the line resistances. It is obvious that the
VLOAD is less than the VOUT by the sum of the voltage drops along the line resistances. In this case, the load regulation seen at the
RLOAD would be degraded from the data sheet specification. To improve this, the load should be tied directly to the output terminal
on the positive side and directly tied to the ground terminal on the negative side.
Copyright © 1999-2012, Texas Instruments Incorporated
11
LM1117/LM1117I
10091918
FIGURE 2. Typical Application using Fixed Output Regulator
When the adjustable regulator is used (Figure 3), the best performance is obtained with the positive side of the resistor R1 tied
directly to the output terminal of the regulator rather than near the load. This eliminates line drops from appearing effectively in
series with the reference and degrading regulation. For example, a 5V regulator with 0.05Ω resistance between the regulator and
load will have a load regulation due to line resistance of 0.05Ω x IL. If R1 (=125Ω) is connected near the load, the effective line
resistance will be 0.05Ω (1+R2/R1) or in this case, it is 4 times worse. In addition, the ground side of the resistor R2 can be returned
near the ground of the load to provide remote ground sensing and improve load regulation.
10091919
FIGURE 3. Best Load Regulation using Adjustable Output Regulator
4.0 PROTECTION DIODES
Under normal operation, the LM1117 regulators do not need any protection diode. With the adjustable device, the internal resistance
between the adjust and output terminals limits the current. No diode is needed to divert the current around the regulator even with
capacitor on the adjust terminal. The adjust pin can take a transient signal of ±25V with respect to the output voltage without
damaging the device.
When a output capacitor is connected to a regulator and the input is shorted to ground, the output capacitor will discharge into the
output of the regulator. The discharge current depends on the value of the capacitor, the output voltage of the regulator, and rate
of decrease of VIN. In the LM1117 regulators, the internal diode between the output and input pins can withstand microsecond
surge currents of 10A to 20A. With an extremely large output capacitor (≥1000 µF), and with input instantaneously shorted to
ground, the regulator could be damaged.
In this case, an external diode is recommended between the output and input pins to protect the regulator, as shown in Figure 4.
12
Copyright © 1999-2012, Texas Instruments Incorporated
LM1117/LM1117I
10091915
FIGURE 4. Regulator with Protection Diode
5.0 HEATSINK REQUIREMENTS
When an integrated circuit operates with an appreciable current, its junction temperature is elevated. It is important to quantify its
thermal limits in order to achieve acceptable performance and reliability. This limit is determined by summing the individual parts
consisting of a series of temperature rises from the semiconductor junction to the operating environment. A one-dimensional steadystate model of conduction heat transfer is demonstrated in Figure 5. The heat generated at the device junction flows through the
die to the die attach pad, through the lead frame to the surrounding case material, to the printed circuit board, and eventually to
the ambient environment. Below is a list of variables that may affect the thermal resistance and in turn the need for a heatsink.
RθJC (Component
Variables)
Leadframe Size & Material
No. of Conduction Pins
Die Size
Die Attach Material
Molding Compound Size
and Material
Rθ CA (Application
Variables)
Mounting Pad Size,
Material, & Location
Placement of Mounting Pad
PCB Size & Material
Traces Length & Width
Adjacent Heat Sources
Volume of Air
Ambient Temperatue
Shape of Mounting Pad
10091937
FIGURE 5. Cross-sectional view of Integrated Circuit Mounted on a printed circuit board. Note that the case temperature
is measured at the point where the leads contact with the mounting pad surface
The LM1117 regulators have internal thermal shutdown to protect the device from over-heating. Under all possible operating
conditions, the junction temperature of the LM1117 must be within the range of 0°C to 125°C. A heatsink may be required depending
on the maximum power dissipation and maximum ambient temperature of the application. To determine if a heatsink is needed,
the power dissipated by the regulator, PD , must be calculated:
IIN = IL + IG
PD = (VIN-VOUT)I L + VINIG
Figure 6 shows the voltages and currents which are present in the circuit.
Copyright © 1999-2012, Texas Instruments Incorporated
13
LM1117/LM1117I
10091916
FIGURE 6. Power Dissipation Diagram
The next parameter which must be calculated is the maximum allowable temperature rise, TR(max):
TR(max) = TJ(max)-TA(max)
where TJ(max) is the maximum allowable junction temperature (125°C), and TA(max) is the maximum ambient temperature which
will be encountered in the application.
Using the calculated values for TR(max) and PD, the maximum allowable value for the junction-to-ambient thermal resistance
(θJA) can be calculated:
θJA = TR(max)/PD
If the maximum allowable value for θJA is found to be ≥136°C/W for SOT-223 package or ≥79°C/W for TO-220 package or ≥92°
C/W for TO-252 package, no heatsink is needed since the package alone will dissipate enough heat to satisfy these requirements.
If the calculated value for θJA falls below these limits, a heatsink is required.
As a design aid, Table 1 shows the value of the θJA of SOT-223 and TO-252 for different heatsink area. The copper patterns that
we used to measure these θJAs are shown at the end of the Application Notes Section. Figure 7 and Figure 8 reflects the same
test results as what are in the Table 1
Figure 9 and Figure 10 shows the maximum allowable power dissipation vs. ambient temperature for the SOT-223 and TO-252
device. Figures Figure 11 and Figure 12 shows the maximum allowable power dissipation vs. copper area (in2) for the SOT-223
and TO-252 devices. Please see AN1028 for power enhancement techniques to be used with SOT-223 and TO-252 packages.
*Application Note AN-1187 discusses improved thermal performance and power dissipation for the LLP.
TABLE 1. θJA Different Heatsink Area
Layout
Copper Area
Top Side
(in2)*
Thermal Resistance
Bottom Side
(in2)
(θJA,°C/W) SOT-223
(θJA,°C/W) TO-252
1
0.0123
0
136
103
2
0.066
0
123
87
3
0.3
0
84
60
4
0.53
0
75
54
5
0.76
0
69
52
6
1
0
66
47
7
0
0.2
115
84
8
0
0.4
98
70
9
0
0.6
89
63
10
0
0.8
82
57
11
0
1
79
57
12
0.066
0.066
125
89
13
0.175
0.175
93
72
14
0.284
0.284
83
61
15
0.392
0.392
75
55
16
0.5
0.5
70
53
*Tab of device attached to topside copper
14
Copyright © 1999-2012, Texas Instruments Incorporated
LM1117/LM1117I
10091913
FIGURE 7. θJA vs. 1oz Copper Area for SOT-223
10091934
FIGURE 8. θJA vs. 2oz Copper Area for TO-252
10091912
FIGURE 9. Maximum Allowable Power Dissipation vs. Ambient Temperature for SOT-223
Copyright © 1999-2012, Texas Instruments Incorporated
15
LM1117/LM1117I
10091936
FIGURE 10. Maximum Allowable Power Dissipation vs. Ambient Temperature for TO-252
10091914
FIGURE 11. Maximum Allowable Power Dissipation vs. 1oz Copper Area for SOT-223
10091935
FIGURE 12. Maximum Allowable Power Dissipation vs. 2oz Copper Area for TO-252
16
Copyright © 1999-2012, Texas Instruments Incorporated
LM1117/LM1117I
10091941
FIGURE 13. Top View of the Thermal Test Pattern in Actual Scale
Copyright © 1999-2012, Texas Instruments Incorporated
17
LM1117/LM1117I
10091942
FIGURE 14. Bottom View of the Thermal Test Pattern in Actual Scale
18
Copyright © 1999-2012, Texas Instruments Incorporated
LM1117/LM1117I
Typical Application Circuits
10091930
Adjusting Output of Fixed Regulators
10091931
Regulator with Reference
10091929
1.25V to 10V Adjustable Regulator with Improved Ripple Rejection
10091927
5V Logic Regulator with Electronic Shutdown*
Copyright © 1999-2012, Texas Instruments Incorporated
19
LM1117/LM1117I
10091932
Battery Backed-Up Regulated Supply
10091933
Low Dropout Negative Supply
20
Copyright © 1999-2012, Texas Instruments Incorporated
LM1117/LM1117I
Physical Dimensions inches (millimeters) unless otherwise noted
3-Lead SOT-223
NS Package Number MP04A
3-Lead TO-220
NS Package Number T03B
Copyright © 1999-2012, Texas Instruments Incorporated
21
LM1117/LM1117I
3-Lead TO-263
NS Package Number TS3B
22
Copyright © 1999-2012, Texas Instruments Incorporated
LM1117/LM1117I
3-Lead TO-252
NS Package Number TD03B
8-Lead LLP
NS Package Number LDC08A
Copyright © 1999-2012, Texas Instruments Incorporated
23
Notes
Copyright © 1999-2012, Texas Instruments
Incorporated
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
Similar pages