± SLLS409K − JANUARY 2000 − REVISED MARCH 2004 D RS-232 Bus-Pin ESD Protection Exceeds D D D D D D D D D DB, DW, OR PW PACKAGE (TOP VIEW) ±15 kV Using Human-Body Model (HBM) Meets or Exceeds the Requirements of TIA/EIA-232-F and ITU v.28 Standards Operates With 3-V to 5.5-V VCC Supply Operates Up To 250 kbit/s Two Drivers and Two Receivers Low Standby Current . . . 1 µA Typical External Capacitors . . . 4 × 0.1 µF Accepts 5-V Logic Input With 3.3-V Supply Alternative High-Speed Pin-Compatible Device (1 Mbit/s) − SNx5C3223 Applications − Battery-Powered Systems, PDAs, Notebooks, Laptops, Palmtop PCs, and Hand-Held Equipment EN C1+ V+ C1− C2+ C2− V− DOUT2 RIN2 ROUT2 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 FORCEOFF VCC GND DOUT1 RIN1 ROUT1 FORCEON DIN1 DIN2 INVALID description/ordering information The MAX3223 consists of two line drivers, two line receivers, and a dual charge-pump circuit with ±15-kV ESD protection pin to pin (serial-port connection pins, including GND). The device meets the requirements of TIA/EIA-232-F and provides the electrical interface between an asynchronous communication controller and the serial-port connector. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-V supply. The device operates at data signaling rates up to 250 kbit/s and a maximum of 30-V/µs driver output slew rate. ORDERING INFORMATION SOIC (DW) −0°C to 70°C SSOP (DB) TSSOP (PW) SOIC (DW) −40°C to 85°C ORDERABLE PART NUMBER PACKAGE† TA SSOP (DB) TSSOP (PW) Tube of 25 MAX3223CDW Reel of 2000 MAX3223CDWR Tube of 70 MAX3223CDB Reel of 2000 MAX3223CDBR Tube of 70 MAX3223CPW Reel of 2000 MAX3223CPWR Tube of 25 MAX3223IDW Reel of 2000 MAX3223IDWR Tube of 70 MAX3223IDB Reel of 2000 MAX3223IDBR Tube of 70 MAX3223IPW Reel of 2000 MAX3223IPWR TOP-SIDE MARKING MAX3223C MA3223C MA3223C MAX3223I MB3223I MB3223I † Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2004, Texas Instruments Incorporated !"#$ % &'!!($ #% )'*+&#$ ,#$( !,'&$% &!" $ %)(&&#$% )(! $-( $(!"% (.#% %$!'"($% %$#,#!, /#!!#$0 !,'&$ )!&(%%1 ,(% $ (&(%%#!+0 &+',( $(%$1 #++ )#!#"($(!% POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 ± SLLS409K − JANUARY 2000 − REVISED MARCH 2004 description/ordering information (continued) Flexible control options for power management are available when the serial port is inactive. The auto-powerdown feature functions when FORCEON is low and FORCEOFF is high. During this mode of operation, if the device does not sense a valid RS-232 signal, the driver outputs are disabled. If FORCEOFF is set low and EN is high, both drivers and receivers are shut off, and the supply current is reduced to 1 µA. Disconnecting the serial port or turning off the peripheral drivers causes auto-powerdown to occur. Auto-powerdown can be disabled when FORCEON and FORCEOFF are high. With auto-powerdown enabled, the device is activated automatically when a valid signal is applied to any receiver input. The INVALID output is used to notify the user if an RS-232 signal is present at any receiver input. INVALID is high (valid data) if any receiver input voltage is greater than 2.7 V or less than −2.7 V, or has been between −0.3 V and 0.3 V for less than 30 µs. INVALID is low (invalid data) if the receiver input voltage is between −0.3 V and 0.3 V for more than 30 µs. Refer to Figure 4 for receiver input levels. Function Tables EACH DRIVER INPUTS OUTPUT DOUT DRIVER STATUS X Z Powered off Normal operation with auto-powerdown disabled DIN FORCEON FORCEOFF VALID RIN RS-232 LEVEL X X L L H H X H H H H X L L L H Yes H H L H Yes L L L H No Z H L H No Z Normal operation with auto-powerdown enabled Powered off by auto-powerdown feature H = high level, L = low level, X = irrelevant, Z = high impedance EACH RECEIVER INPUTS RIN EN VALID RIN RS-232 LEVEL OUTPUT ROUT L L X H H L X L X H X Z Open L No H H = high level, L = low level, X = irrelevant, Z = high impedance (off), Open = input disconnected or connected driver off 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 ± SLLS409K − JANUARY 2000 − REVISED MARCH 2004 logic diagram (positive logic) 17 13 DIN1 DOUT1 8 12 DIN2 FORCEOFF DOUT2 20 14 Auto-powerdown 11 INVALID FORCEON 1 EN 16 15 ROUT1 RIN1 9 10 ROUT2 RIN2 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 6 V Positive output supply voltage range, V+ (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 7 V Negative output supply voltage range, V− (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.3 V to −7 V Supply voltage difference, V+ − V− (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 V Input voltage range, VI: Driver, FORCEOFF, FORCEON, EN . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 6 V Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −25 V to 25 V Output voltage range, VO: Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −13.2 V to 13.2 V Receiver, INVALID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to VCC + 0.3 V Package thermal impedance, θJA (see Notes 2 and 3): DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . 70°C/W DW package . . . . . . . . . . . . . . . . . . . . . . . . . . 58°C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . . 83°C/W Operating virtual junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltages are with respect to network GND. 2. Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD = (TJ(max) − TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability. 3. The package thermal impedance is calculated in accordance with JESD 51-7. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 ± SLLS409K − JANUARY 2000 − REVISED MARCH 2004 recommended operating conditions (see Note 4 and Figure 6) Supply voltage DIN, EN, FORCEOFF, FORCEON VCC = 3.3 V VCC = 5 V VCC = 3.3 V VIH Driver and control high-level input voltage VIL Driver and control low-level input voltage VCC = 5 V DIN, EN, FORCEOFF, FORCEON Driver and control input voltage DIN, EN, FORCEOFF, FORCEON VI Receiver input voltage TA Operating free-air temperature MAX3223C MAX3223I MIN NOM MAX 3 3.3 3.6 4.5 5 5.5 UNIT V 2 V 2.4 0.8 0 5.5 −25 25 0 70 −40 85 V V °C NOTE 4: Test conditions are C1−C4 = 0.1 µF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 µF, C2−C4 = 0.33 µF at VCC = 5 V ± 0.5 V. electrical characteristics over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Note 4 and Figure 6) PARAMETER II Input leakage current TEST CONDITIONS EN, FORCEOFF, FORCEON Auto-powerdown disabled ICC Supply current Powered off VCC = 3.3 V or 5 V, TA = 25°C Auto-powerdown enabled No load, FORCEOFF and FORCEON at VCC No load, FORCEOFF at GND No load, FORCEOFF at VCC, FORCEON at GND, All RIN are open or grounded MIN TYP† MAX ±0.01 ±1 µA 0.3 1 mA 1 10 1 10 † All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C. NOTE 4: Test conditions are C1−C4 = 0.1 µF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 µF, C2−C4 = 0.33 µF at VCC = 5 V ± 0.5 V. 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 UNIT µA ± SLLS409K − JANUARY 2000 − REVISED MARCH 2004 DRIVER SECTION electrical characteristics over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Note 4 and Figure 6) PARAMETER TEST CONDITIONS MIN TYP† VOH VOL High-level output voltage DOUT at RL = 3 kΩ to GND 5 5.4 Low-level output voltage DOUT at RL = 3 kΩ to GND −5 −5.4 IIH IIL High-level input current VI = VCC VI at GND Low-level input current ±0.01 IOS Short-circuit output current‡ VCC = 3.6 V, VCC = 5.5 V, ro Output resistance VCC, V+, and V− = 0 V, Ioff Output leakage current FORCEOFF = GND VO = 0 V VO = 0 V VO = ±2 V 300 MAX UNIT V V ±1 µA ±0.01 ±1 µA ±35 ±60 ±35 ±60 mA Ω 10M VO = ±12 V, VCC = 3 V to 3.6 V ±25 VO = ±10 V, VCC = 4.5 V to 5.5 V ±25 µA † All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C. ‡ Short-circuit durations should be controlled to prevent exceeding the device absolute power-dissipation ratings, and not more than one output should be shorted at a time. NOTE 4: Test conditions are C1−C4 = 0.1 µF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 µF, C2−C4 = 0.33 µF at VCC = 5 V ± 0.5 V. switching characteristics over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Note 4 and Figure 6) PARAMETER TEST CONDITIONS MIN TYP† MAX Maximum data rate CL = 1000 pF, One DOUT switching, RL = 3 kΩ, See Figure 1 tsk(p) Pulse skew§ CL = 150 pF to 2500 pF, See Figure 2 RL = 3 kΩ to 7 kΩ, SR(tr) Slew rate, transition region (See Figure 1) VCC = 3.3 V, RL = 3 kΩ to 7 kΩ CL = 150 pF to 1000 pF 6 30 CL = 150 pF to 2500 pF 4 30 250 UNIT kbit/s 100 ns V/µs † All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C. § Pulse skew is defined as |tPLH − tPHL| of each channel of the same device. NOTE 4: Test conditions are C1−C4 = 0.1 µF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 µF, C2−C4 = 0.33 µF at VCC = 5 V ± 0.5 V. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 ± SLLS409K − JANUARY 2000 − REVISED MARCH 2004 RECEIVER SECTION electrical characteristics over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Note 4 and Figure 6) PARAMETER VOH VOL TEST CONDITIONS High-level output voltage IOH = −1 mA IOL = 1.6 mA Low-level output voltage VIT+ Positive-going input threshold voltage VCC = 3.3 V VCC = 5 V VIT− Negative-going input threshold voltage VCC = 3.3 V VCC = 5 V Vhys Ioff Input hysteresis (VIT+ − VIT−) MIN TYP† VCC−0.6 VCC−0.1 MAX V 0.4 1.6 2.4 1.9 2.4 0.6 1.1 0.8 1.4 ±0.05 EN = VCC ri Input resistance VI = ±3 V to ±25 V 3 5 † All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C. NOTE 4: Test conditions are C1−C4 = 0.1 µF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 µF, C2−C4 = 0.33 µF at VCC = 5 V ± 0.5 V. V V V 0.5 Output leakage current UNIT V ±10 µA 7 kΩ switching characteristics over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Note 4) PARAMETER tPLH tPHL TEST CONDITIONS MIN TYP† UNIT CL= 150 pF, See Figure 3 150 ns Propagation delay time, high- to low-level output CL= 150 pF, See Figure 3 150 ns ten Output enable time CL= 150 pF, See Figure 4 RL = 3 kΩ, 200 ns tdis Output disable time CL= 150 pF, See Figure 4 RL = 3 kΩ, 200 ns tsk(p) Pulse skew‡ See Figure 3 50 † All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C. ‡ Pulse skew is defined as |tPLH − tPHL| of each channel of the same device. NOTE 4: Test conditions are C1−C4 = 0.1 µF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 µF, C2−C4 = 0.33 µF at VCC = 5 V ± 0.5 V. 6 MAX Propagation delay time, low- to high-level output POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 ns ± SLLS409K − JANUARY 2000 − REVISED MARCH 2004 AUTO-POWERDOWN SECTION electrical characteristics over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 5) PARAMETER TEST CONDITIONS MIN VT+(valid) Receiver input threshold for INVALID high-level output voltage FORCEON = GND, FORCEOFF = VCC VT−(valid) Receiver input threshold for INVALID high-level output voltage FORCEON = GND, FORCEOFF = VCC −2.7 VT(invalid) Receiver input threshold for INVALID low-level output voltage FORCEON = GND, FORCEOFF = VCC −0.3 VOH INVALID high-level output voltage IOH = −1 mA, FORCEOFF = VCC FORCEON = GND, VOL INVALID low-level output voltage IOL = 1.6 mA, FORCEOFF = VCC FORCEON = GND, MAX UNIT 2.7 V V 0.3 V VCC−0.6 V 0.4 V switching characteristics over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 5) TYP† PARAMETER tvalid tinvalid UNIT Propagation delay time, low- to high-level output 1 µs Propagation delay time, high- to low-level output 30 µs 100 µs ten Supply enable time † All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C. PARAMETER MEASUREMENT INFORMATION 3V Input Generator (see Note B) 1.5 V RS-232 Output 50 Ω RL 1.5 V 0V CL (see Note A) tTHL 3V FORCEOFF Output tTLH 3V −3 V TEST CIRCUIT 3V −3 V VOH VOL VOLTAGE WAVEFORMS SR(tr) + t THL 6V or t TLH NOTES: A. CL includes probe and jig capacitance. B. The pulse generator has the following characteristics: PRR = 250 kbit/s, ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns. Figure 1. Driver Slew Rate POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 ± SLLS409K − JANUARY 2000 − REVISED MARCH 2004 PARAMETER MEASUREMENT INFORMATION 3V Generator (see Note B) Input RS-232 Output 50 Ω 0V tPHL CL (see Note A) RL 3V FORCEOFF 1.5 V 1.5 V tPLH VOH 50% 50% Output VOL TEST CIRCUIT VOLTAGE WAVEFORMS NOTES: A. CL includes probe and jig capacitance. B. The pulse generator has the following characteristics: PRR = 250 kbit/s, ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns. Figure 2. Driver Pulse Skew EN 0V 3V Input 1.5 V 1.5 V −3 V Output Generator (see Note B) 50 Ω tPHL CL (see Note A) tPLH VOH 50% Output 0V FORCEOFF 50% VOL TEST CIRCUIT VOLTAGE WAVEFORMS NOTES: A. CL includes probe and jig capacitance. B. The pulse generator has the following characteristics: ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns. Figure 3. Receiver Propagation Delay Times 3V FORCEON 3 V or 0 V VCC S1 GND 1.5 V 0V tPHZ (S1 at GND) Output CL (see Note A) EN Generator (see Note B) 1.5 V tPHZ (S1 at GND) RL 3 V or 0 V Input VOH Output 50% 0.3 V tPLZ (S1 at VCC) 0.3 V 50 Ω Output 50% VOL tPZL (S1 at VCC) TEST CIRCUIT VOLTAGE WAVEFORMS NOTES: A. CL includes probe and jig capacitance. B. The pulse generator has the following characteristics: ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns. Figure 4. Receiver Enable and Disable Times 8 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 ± SLLS409K − JANUARY 2000 − REVISED MARCH 2004 PARAMETER MEASUREMENT INFORMATION 2.7 V 2.7 V 0V Receiver Input 0V 50 Ω tinvalid 50% VCC 50% VCC 0V ten ≈V+ V+ 0.3 V VCC 0V 0.3 V Supply Voltages FORCEOFF FORCEON tvalid INVALID CL = 30 pF (see Note A) DIN −3 V VCC INVALID Output Autopowerdown −2.7 V −2.7 V ROUT Generator (see Note B) 3V DOUT ≈V− V− TEST CIRCUIT VOLTAGE WAVEFORMS Valid RS-232 Level, INVALID High ÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎ 2.7 V Indeterminate 0.3 V 0V If Signal Remains Within This Region for More Than 30 µs, INVALID Is Low† −0.3 V Indeterminate −2.7 V Valid RS-232 Level, INVALID High † Auto-powerdown disables drivers and reduces supply current to 1 µA. NOTES: A. CL includes probe and jig capacitance. B. The pulse generator has the following characteristics: PRR = 5 kbit/s, ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns. Figure 5. INVALID Propagation Delay Times and Supply Enabling Time POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 9 ± SLLS409K − JANUARY 2000 − REVISED MARCH 2004 APPLICATION INFORMATION 2 + C1 − 3 C3 † + 20 Autopowerdown 1 EN VCC C1+ V+ GND FORCEOFF 19 18 + CBYPASS − = 0.1µF − 4 5 17 C1− 16 C2+ DOUT1 RIN1 + C2 − 6 15 C2− ROUT1 5 kΩ 7 C4 DOUT2 RIN2 ROUT2 − 14 V− FORCEON + 8 13 9 12 10 11 DIN1 DIN2 INVALID 5 kΩ † C3 can be connected to VCC or GND. NOTES: A. Resistor values shown are nominal. B. Nonpolarized ceramic capacitors are acceptable. If polarized tantalum or electrolytic capacitors are used, they should be connected as shown. VCC vs CAPACITOR VALUES VCC C1 C2, C3, C4 3.3 V ± 0.3 V 5 V ± 0.5 V 3 V to 5.5 V 0.1 µF 0.047 µF 0.1 µF 0.1 µF 0.33 µF 0.47 µF Figure 6. Typical Operating Circuit and Capacitor Values 10 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 PACKAGE OPTION ADDENDUM www.ti.com 5-Sep-2005 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty MAX3223CDB ACTIVE SSOP DB 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3223CDBE4 ACTIVE SSOP DB 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3223CDBR ACTIVE SSOP DB 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3223CDBRE4 ACTIVE SSOP DB 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3223CDW ACTIVE SOIC DW 20 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3223CDWE4 ACTIVE SOIC DW 20 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3223CDWR ACTIVE SOIC DW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3223CPW ACTIVE TSSOP PW 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3223CPWE4 ACTIVE TSSOP PW 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3223CPWR ACTIVE TSSOP PW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3223CPWRE4 ACTIVE TSSOP PW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3223IDB ACTIVE SSOP DB 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3223IDBE4 ACTIVE SSOP DB 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3223IDBR ACTIVE SSOP DB 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3223IDBRE4 ACTIVE SSOP DB 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3223IDW ACTIVE SOIC DW 20 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3223IDWE4 ACTIVE SOIC DW 20 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3223IDWR ACTIVE SOIC DW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3223IDWRE4 ACTIVE SOIC DW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3223IPW ACTIVE TSSOP PW 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3223IPWE4 ACTIVE TSSOP PW 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3223IPWR ACTIVE TSSOP PW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3223IPWRE4 ACTIVE TSSOP PW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. Addendum-Page 1 Lead/Ball Finish MSL Peak Temp (3) PACKAGE OPTION ADDENDUM www.ti.com 5-Sep-2005 NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 MECHANICAL DATA MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001 DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE 28 PINS SHOWN 0,38 0,22 0,65 28 0,15 M 15 0,25 0,09 8,20 7,40 5,60 5,00 Gage Plane 1 14 0,25 A 0°–ā8° 0,95 0,55 Seating Plane 2,00 MAX 0,10 0,05 MIN PINS ** 14 16 20 24 28 30 38 A MAX 6,50 6,50 7,50 8,50 10,50 10,50 12,90 A MIN 5,90 5,90 6,90 7,90 9,90 9,90 12,30 DIM 4040065 /E 12/01 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-150 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MECHANICAL DATA MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999 PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PINS SHOWN 0,30 0,19 0,65 14 0,10 M 8 0,15 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 1 7 0°– 8° A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 8 14 16 20 24 28 A MAX 3,10 5,10 5,10 6,60 7,90 9,80 A MIN 2,90 4,90 4,90 6,40 7,70 9,60 DIM 4040064/F 01/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2005, Texas Instruments Incorporated