FEATURES High efficiency: 94% @ 5.0Vin, 3.3V/6A out Small size and low profile: (SIP) 25.4 x 12.7 x 6.7mm (1.00”x 0.50”x 0.26”) Single-In-Line (SIP) packaging Standard footprint Voltage and resistor-based trim Pre-bias startup Output voltage tracking No minimum load required Output voltage programmable from 0.75Vdc to 3.3Vdc via external resistor Fixed frequency operation Input UVLO, output OTP, OCP Remote on/off ISO 9001, TL 9000, ISO 14001, QS9000, OHSAS18001 certified manufacturing facility UL/cUL 60950 (US & Canada) Recognized, and TUV (EN60950) Certified CE mark meets 73/23/EEC and 93/68/EEC directives Delphi DNS, Non-Isolated Point of Load DC/DC Power Modules: 2.8-5.5Vin, 0.75-3.3V/6Aout The Delphi Series DNS, 2.8-5.5V input, single output, non-isolated Point of Load DC/DC converters are the latest offering from a world OPTIONS leader in power systems technology and manufacturing -- Delta Negative on/off logic Electronics, Inc. The DNS series provides a programmable output Tracking feature voltage from 0.75V to 3.3V using an external resistor and has flexible SIP package and programmable tracking features to enable a variety of startup voltages as well as tracking between power modules. This product family is available in surface mount or SIP packages and provides up to 6A of output current in an industry standard footprint. With creative design technology and optimization of component placement, these converters possess outstanding electrical and thermal performance, APPLICATIONS Telecom / DataCom Distributed power architectures Servers and workstations as well as extremely high reliability under highly stressful operating LAN / WAN applications conditions. Data processing applications DATASHEET DS_DNS04SIP06_07172008D TECHNICAL SPECIFICATIONS (TA = 25°C, airflow rate = 300 LFM, Vin = 2.8Vdc and 5.5Vdc, nominal Vout unless otherwise noted.) PARAMETER NOTES and CONDITIONS DNS04S0A0R06PFD Min. ABSOLUTE MAXIMUM RATINGS Input Voltage (Continuous) Tracking Voltage Operating Temperature Storage Temperature INPUT CHARACTERISTICS Operating Input Voltage Input Under-Voltage Lockout Turn-On Voltage Threshold Turn-Off Voltage Threshold Maximum Input Current No-Load Input Current Off Converter Input Current Inrush Transient Recommended Inout Fuse OUTPUT CHARACTERISTICS Output Voltage Set Point Output Voltage Adjustable Range Output Voltage Regulation Over Line Over Load Over Temperature Total Output Voltage Range Output Voltage Ripple and Noise Peak-to-Peak RMS Output Current Range Output Voltage Over-shoot at Start-up Output DC Current-Limit Inception Output Short-Circuit Current (Hiccup Mode) DYNAMIC CHARACTERISTICS Dynamic Load Response Positive Step Change in Output Current Negative Step Change in Output Current Settling Time to 10% of Peak Deviation Turn-On Transient Start-Up Time, From On/Off Control Start-Up Time, From Input Output Voltage Rise Time Output Capacitive Load EFFICIENCY Vo=3.3V Vo=2.5V Vo=1.8V Vo=1.5V Vo=1.2V Vo=0.75V FEATURE CHARACTERISTICS Switching Frequency ON/OFF Control, (Negative logic) Logic Low Voltage Logic High Voltage Logic Low Current Logic High Current ON/OFF Control, (Positive Logic) Logic High Voltage Logic Low Voltage Logic Low Current Logic High Current Tracking Slew Rate Capability Tracking Delay Time Tracking Accuracy GENERAL SPECIFICATIONS MTBF Weight Over-Temperature Shutdown DS_DNS04SIP06A_07172008 Typ. 0 Max. Units Vdc Vdc °C °C Refer to Figure 44 for measuring point -40 -55 5.8 Vin,max 125 125 Vout ≦ Vin –0.5 2.8 5.5 2.2 2.0 Vin=2.8V to 5.5V, Io=Io,max 0.1 6 V V A mA mA A 2S A +2.0 3.63 % Vo,set V +3.0 % Vo,set % Vo,set % Vo,set % Vo,set 6 70 5 Vin=2.8V to 5.5V, Io=Io,min to Io,max Vin=5V, Io=Io, max Vin=2.8V to 5.5V Io=Io,min to Io,max Ta=-40℃ to 85℃ Over sample load, line and temperature 5Hz to 20MHz bandwidth Full Load, 1µF ceramic, 10µF tantalum Full Load, 1µF ceramic, 10µF tantalum -2.0 0.7525 Vo,set 0.3 0.4 0.8 -3.0 40 10 220 3.5 mV mV A % Vo,set % Io Adc 160 160 25 mV mV µs 2 2 2 ms ms ms µF µF 0 Vout=3.3V Io,s/c 10µF Tan & 1µF Ceramic load cap, 2.5A/µs, Vin=5V 50% Io, max to 100% Io, max 100% Io, max to 50% Io, max Io=Io.max Von/off, Vo=10% of Vo,set Vin=Vin,min, Vo=10% of Vo,set Time for Vo to rise from 10% to 90% of Vo,set Full load; ESR ≧1mΩ Full load; ESR ≧10mΩ Vin=5V, 100% Load Vin=5V, 100% Load Vin=5V, 100% Load Vin=5V, 100% Load Vin=5V, 100% Load Vin=5V, 100% Load Module On, Von/off Module Off, Von/off Module On, Ion/off Module Off, Ion/off Module On, Von/off Module Off, Von/off Module On, Ion/off Module Off, Ion/off Delay from Vin.min to application of tracking voltage Power-up 2V/mS Power-down 1V/mS Io=80% of Io, max; Ta=25°C Refer to Figure 45 for measuring point V 60 15 6 1 5 1000 3000 94.0 91.5 89.0 88.0 86.0 81.0 % % % % % % 300 kHz -0.2 1.5 0.3 Vin,max 10 1 V V µA mA 0.2 Vin,max 0.3 1 10 2 100 200 200 400 V V mA µA V/msec ms mV mV 0.2 -0.2 0.1 10 11.52 4 130 M hours grams °C 2 98 98 97 96 96 94 EFFICIENCY(%) EFFICIENCY(%) ELECTRICAL CHARACTERISTICS CURVES 95 94 93 92 91 88 5V 86 3 4 5 3V 5V 5.5V 84 90 2 90 4.5V 5.5V 1 92 1 6 2 3 LOAD (A) 98 96 96 94 94 92 92 90 2.8V 88 6 90 88 86 5V 86 5 Figure 2: Converter efficiency vs. output current (2.5V out) EFFICIENCY(%) EFFICIENCY(%) Figure 1: Converter efficiency vs. output current (3.3V out) 4 LOAD (A) 5.5V 2.8V 5V 84 5.5V 84 1 2 3 4 5 82 6 1 LOAD (A) 2 3 4 5 6 LOAD (A) Figure 3: Converter efficiency vs. output current (1.8V out) Figure 4: Converter efficiency vs. output current (1.5V out) 94 92 92 90 88 EFFICIENCY(%) EFFICIENCY(%) 90 88 86 84 2.8V 84 82 80 2.8V 78 5V 82 86 5V 76 5.5V 5.5V 74 80 1 2 3 4 5 LOAD (A) Figure 5: Converter efficiency vs. output current (1.2V out) DS_DNS04SIP06A_07172008 6 1 2 3 4 5 6 LOAD (A) Figure 6: Converter efficiency vs. output current (0.75V out) 3 ELECTRICAL CHARACTERISTICS CURVES (CON.) Figure 7: Output ripple & noise at 3.3Vin, 2.5V/6A out Figure 8: Output ripple & noise at 3.3Vin, 1.8V/6A out Figure 9: Output ripple & noise at 5Vin, 3.3V/6A out Figure 10: Output ripple & noise at 5Vin, 1.8V/6A out Figure 11: Turn on delay time at 3.3Vin, 2.5V/6A out Figure 12: Turn on delay time at 3.3Vin, 1.8V/6A out DS_DNS04SIP06A_07172008 4 ELECTRICAL CHARACTERISTICS CURVES (CON.) Figure 13: Turn on delay time at 5Vin, 3.3V/6A out Figure 14: Turn on delay time at 5Vin, 1.8V/6A out Figure 15: Turn on delay time at remote turn on 5Vin, 3.3V/16A Figure 16: Turn on delay time at remote turn on 3.3Vin, 2.5V/16A out out Figure 17: Turn on delay time at remote turn on with external Figure 18: Turn on delay time at remote turn on with external capacitors (Co= 5000 µF) 5Vin, 3.3V/16A out capacitors (Co= 5000 µF) 3.3Vin, 2.5V/16A out DS_DNS04SIP06A_07172008 5 ELECTRICAL CHARACTERISTICS CURVES Figure 19: Typical transient response to step load change at 2.5A/μS from 100% to 50% of Io, max at 5Vin, 3.3Vout (Cout = 1uF ceramic, 10μF tantalum) Figure 20: Typical transient response to step load change at 2.5A/μS from 50% to 100% of Io, max at 5Vin, 3.3Vout (Cout =1uF ceramic, 10μF tantalum) Figure 21: Typical transient response to step load change at 2.5A/μS from 100% to 50% of Io, max at 5Vin, 1.8Vout (Cout =1uF ceramic, 10μF tantalum) Figure 22: Typical transient response to step load change at 2.5A/μS from 50% to 100% of Io, max at 5Vin, 1.8Vout (Cout = 1uF ceramic, 10μF tantalum) DS_DNS04SIP06A_07172008 6 ELECTRICAL CHARACTERISTICS CURVES (CON.) Figure 23: Typical transient response to step load change at 2.5A/μS from 100% to 50% of Io, max at 3.3Vin, 2.5Vout (Cout =1uF ceramic, 10μF tantalum) Figure 24: Typical transient response to step load change at 2.5A/μS from 50% to 100% of Io, max at 3.3Vin, 2.5Vout (Cout =1uF ceramic, 10μF tantalum) Figure 25: Typical transient response to step load change at 2.5A/μS from 100% to 50% of Io, max at 3.3Vin, 1.8Vout (Cout =1uF ceramic, 10μF tantalum) Figure 26: Typical transient response to step load change at 2.5A/μS from 50% to 100% of Io, max at 3.3Vin, 1.8Vout (Cout = 1uF ceramic, 10μF tantalum) Figure 27: Output short circuit current 5Vin, 0.75Vout Figure 28:Turn on with Prebias 5Vin, 3.3V/0A out, Vbias =1.0Vdc DS_DNS04SIP06A_07172008 7 DESIGN CONSIDERATIONS TEST CONFIGURATIONS Input Source Impedance TO OSCILLOSCOPE L VI(+) 2 100uF Tantalum BATTERY VI(-) Note: Input reflected-ripple current is measured with a simulated source inductance. Current is measured at the input of the module. To maintain low noise and ripple at the input voltage, it is critical to use low ESR capacitors at the input to the module. Figure 32 shows the input ripple voltage (mVp-p) for various output models using 2x100 µF low ESR tantalum capacitor (KEMET p/n: T491D107M016AS, AVX p/n: TAJD107M106R, or equivalent) in parallel with 47 µF ceramic capacitor (TDK p/n:C5750X7R1C476M or equivalent). Figure 33 shows much lower input voltage ripple when input capacitance is increased to 400 µF (4 x 100 µF) tantalum capacitors in parallel with 94 µF (2 x 47 µF) ceramic capacitor. The input capacitance should be able to handle an AC ripple current of at least: Figure 29: Input reflected-ripple test setup Irms = Iout COPPER STRIP 1uF 10uF SCOPE tantalum ceramic Resistive Load GND Input Ripple Voltage (mVp-p) Vo Vout ⎛ Vout ⎞ ⎜1 − ⎟ Vin ⎝ Vin ⎠ Arms 200 150 100 50 Note: Use a 10μF tantalum and 1μF capacitor. Scope measurement should be made using a BNC connector. 3.3Vin 5.0Vin 0 0 1 2 3 4 Output Voltage (Vdc) Figure 30: Peak-peak output noise and startup transient measurement test setup. Figure 32: Input voltage ripple for various output models, Io = 6A (CIN = 2×100µF tantalum // 47µF ceramic) CONTACT AND DISTRIBUTION LOSSES Vo Io II LOAD SUPPLY GND CONTACT RESISTANCE Figure 31: Output voltage and efficiency measurement test setup Note: All measurements are taken at the module terminals. When the module is not soldered (via socket), place Kelvin connections at module terminals to avoid measurement errors due to contact resistance. η =( 80 Input Ripple Voltage (mVp-p) VI 60 40 20 3.3Vin 5.0Vin 0 0 1 2 3 4 Output Voltage (Vdc) Figure 33: Input voltage ripple for various output models, Io = 6A (CIN = 4×100µF tantalum // 2×47µF ceramic) Vo × Io ) × 100 % Vi × Ii DS_DNS04SIP06A_07172008 8 DESIGN CONSIDERATIONS (CON.) FEATURES DESCRIPTIONS The power module should be connected to a low ac-impedance input source. Highly inductive source impedances can affect the stability of the module. An input capacitance must be placed close to the modules input pins to filter ripple current and ensure module stability in the presence of inductive traces that supply the input voltage to the module. Remote On/Off Safety Considerations For safety-agency approval the power module must be installed in compliance with the spacing and separation requirements of the end-use safety agency standards. For the converter output to be considered meeting the requirements of safety extra-low voltage (SELV), the input must meet SELV requirements. The power module has extra-low voltage (ELV) outputs when all inputs are ELV. The input to these units is to be provided with a maximum 6A time-delay fuse in the ungrounded lead. The DNS series power modules have an On/Off pin for remote On/Off operation. Both positive and negative On/Off logic options are available in the DNS series power modules. For positive logic module, connect an open collector (NPN) transistor or open drain (N channel) MOSFET between the On/Off pin and the GND pin (see figure 34). Positive logic On/Off signal turns the module ON during the logic high and turns the module OFF during the logic low. When the positive On/Off function is not used, leave the pin floating or tie to Vin (module will be On). For negative logic module, the On/Off pin is pulled high with an external pull-up 5kΩ resistor (see figure 35). Negative logic On/Off signal turns the module OFF during logic high and turns the module ON during logic low. If the negative On/Off function is not used, leave the pin floating or tie to GND. (module will be On) Vo Vin ION/OFF On/Off RL Q1 GND Figure 34: Positive remote On/Off implementation Vo Vin Rpullup ION/OFF On/Off RL Q1 GND Figure 35: Negative remote On/Off implementation Over-Current Protection To provide protection in an output over load fault condition, the unit is equipped with internal over-current protection. When the over-current protection is triggered, the unit enters hiccup mode. The units operate normally once the fault condition is removed. DS_DNS04SIP06A_07172008 9 FEATURES DESCRIPTIONS (CON.) Vtrim = 0.7 − 0.1698 × (Vo − 0.7525) Over-Temperature Protection For example, to program the output voltage of a DNS module to 3.3 Vdc, Vtrim is calculated as follows The over-temperature protection consists of circuitry that provides protection from thermal damage. If the temperature exceeds the over-temperature threshold the module will shut down. The module will try to restart after shutdown. If the over-temperature condition still exists during restart, the module will shut down again. This restart trial will continue until the temperature is within specification. Remote Sense Vo RLoad TRIM Rtrim GND Figure 37: Circuit configuration for programming output voltage The DNS provide Vo remote sensing to achieve proper regulation at the load points and reduce effects of distribution losses on output line. In the event of an open remote sense line, the module shall maintain local sense regulation through an internal resistor. The module shall correct for a total of 0.5V of loss. The remote sense line impedance shall be < 10Ω. Distribution Losses Vtrim = 0.7 − 0.1698 × (3.3 − 0.7525) = 0.267V Vo Vin Distribution Losses using an external resistor Vo Vtrim RLoad TRIM GND + _ Figure 38: Circuit Configuration for programming output voltage using external voltage source Sense RL GND Distribution Distribution L Figure 36: Effective circuit configuration for remote sense operation Output Voltage Programming The output voltage of the DNS can be programmed to any voltage between 0.75Vdc and 3.3Vdc by connecting one resistor (shown as Rtrim in Figure 37) between the TRIM and GND pins of the module. Without this external resistor, the output voltage of the module is 0.7525 Vdc. To calculate the value of the resistor Rtrim for a particular output voltage Vo, please use the following equation: ⎤ ⎡ 21070 Rtrim = ⎢ − 5110⎥ Ω ⎣Vo − 0.7525 ⎦ Table 1 provides Rtrim values required for some common output voltages, while Table 2 provides value of external voltage source, Vtrim, for the same common output voltages. By using a 1% tolerance trim resistor, set point tolerance of ±2% can be achieved as specified in the electrical specification. Table 1 Vo(V) Rtrim(KΩ) 0.7525 Open 1.2 41.97 1.5 23.08 1.8 15.00 2.5 6.95 3.3 3.16 Table 2 Vo(V) Vtrim(V) 0.7525 Open ⎡ 21070 ⎤ Rtrim = ⎢ − 5110⎥ Ω = 15KΩ ⎣1.8 − 0.7525 ⎦ 1.2 0.624 1.5 0.573 1.8 0.522 DNS can also be programmed by apply a voltage between the TRIM and GND pins (Figure 38). The following equation can be used to determine the value of Vtrim needed for a desired output voltage Vo: 2.5 0.403 3.3 0.267 For example, to program the output voltage of the DNS module to 1.8Vdc, Rtrim is calculated as follows: DS_DNS04SIP06A_07172008 10 FEATURE DESCRIPTIONS (CON.) The amount of power delivered by the module is the voltage at the output terminals multiplied by the output current. When using the trim feature, the output voltage of the module can be increased, which at the same output current would increase the power output of the module. Care should be taken to ensure that the maximum output power of the module must not exceed the maximum rated power (Vo.set x Io.max ≤ P max). Voltage Margining Output voltage margining can be implemented in the DNS modules by connecting a resistor, R margin-up, from the Trim pin to the ground pin for margining-up the output voltage and by connecting a resistor, Rmargin-down, from the Trim pin to the output pin for margining-down. Figure 39 shows the circuit configuration for output voltage margining. If unused, leave the trim pin unconnected. A calculation tool is available from the evaluation procedure which computes the values of R margin-up and Rmargin-down for a specific output voltage and margin percentage. Vin The output voltage tracking feature (Figure 40 to Figure 42) is achieved according to the different external connections. If the tracking feature is not used, the TRACK pin of the module can be left unconnected or tied to Vin. For proper voltage tracking, input voltage of the tracking power module must be applied in advance, and the remote on/off pin has to be in turn-on status. (Negative logic: Tied to GND or unconnected. Positive logic: Tied to Vin or unconnected) PS1 PS1 PS2 PS2 Figure 40: Sequential Start-up Vo Rmargin-down PS1 PS1 PS2 PS2 Q1 On/Off Trim Rmargin-up Rtrim Q2 GND Figure 39: Circuit configuration for output voltage margining Figure 41: Simultaneous -ΔV PS1 PS1 PS2 PS2 Voltage Tracking The DNS family was designed for applications that have output voltage tracking requirements during power-up and power-down. The devices have a TRACK pin to implement three types of tracking method: sequential start-up, simultaneous and ratio-metric. TRACK simplifies the task of supply voltage tracking in a power system by enabling modules to track each other, or any external voltage, during power-up and power-down. Figure 42: Ratio-metric By connecting multiple modules together, customers can get multiple modules to track their output voltages to the voltage applied on the TRACK pin. DS_DNS04SIP06A_07172008 11 FEATURE DESCRIPTIONS (CON.) Ratio-Metric Sequential Start-up Sequential start-up (Figure 40) is implemented by placing an On/Off control circuit between VoPS1 and the On/Off pin of PS2. Ratio–metric (Figure 42) is implemented by placing the voltage divider on the TRACK pin that comprises R1 and R2, to create a proportional voltage with VoPS1 to the Track pin of PS2. For Ratio-Metric applications that need the outputs of PS1 and PS2 reach the regulation set point at the same time. PS1 PS2 Vin Vin VoPS1 VoPS2 R3 On/Off The following equation can be used to calculate the value of R1 and R2. The suggested value of R2 is 10kΩ. R1 Q1 On/Off R2 VO , PS 2 C1 VO ,PS1 = R2 R1 + R2 PS1 PS2 Vin Vin Simultaneous VoPS1 VoPS2 R1 Simultaneous tracking (Figure 41) is implemented by using the TRACK pin. The objective is to minimize the voltage difference between the power supply outputs during power up and down. The simultaneous tracking can be accomplished by connecting VoPS1 to the TRACK pin of PS2. Please note the voltage apply to TRACK pin needs to always higher than the VoPS2 set point voltage. TRACK R2 On/Off On/Off The high for positive logic The low for negative logic PS2 PS1 Vin Vin VoPS1 VoPS2 TRACK On/Off On/Off DS_DNS04SIP06A_07172008 12 THERMAL CONSIDERATIONS THERMAL CURVES Thermal management is an important part of the system design. To ensure proper, reliable operation, sufficient cooling of the power module is needed over the entire temperature range of the module. Convection cooling is usually the dominant mode of heat transfer. Hence, the choice of equipment to characterize the thermal performance of the power module is a wind tunnel. Thermal Testing Setup Delta’s DC/DC power modules are characterized in heated vertical wind tunnels that simulate the thermal environments encountered in most electronics equipment. This type of equipment commonly uses vertically mounted circuit cards in cabinet racks in which the power modules are mounted. The following figure shows the wind tunnel characterization setup. The power module is mounted on a test PWB and is vertically positioned within the wind tunnel. The height of this fan duct is constantly kept at 25.4mm (1’’). Thermal Derating Figure 44: Temperature measurement location The allowed maximum hot spot temperature is defined at 125℃ 7 DNS04S0A0R06(Standard) Output Current vs. Ambient Temperature and Air Velocity @ Vin = 5V, Vo = 3.3V (Either Orientation) Output Current(A) 6 5 4 Natural Convection 3 Heat can be removed by increasing airflow over the module. To enhance system reliability, the power module should always be operated below the maximum operating temperature. If the temperature exceeds the maximum module temperature, reliability of the unit may be affected. PWB FACING PWB MODULE 2 1 0 60 65 70 75 80 85 Ambient Temperature (℃) Figure 45: DNS04S0A0R06 (Standard) Output current vs. ambient temperature and air velocity@Vin=5V, Vo=3.3V (Either Orientation) 7 DNS04S0A0R06(Standard) Output Current vs. Ambient Temperature and Air Velocity @ Vin = 5.0V, Vo = 1.5V (Either Orientation) Output Current(A) 6 AIR VELOCITY AND AMBIENT TEMPERATURE MEASURED BELOW THE MODULE 5 Natural Convection 50.8 (2.0”) 4 AIR FLOW 3 12.7 (0.5”) 25.4 (1.0”) Note: Wind Tunnel Test Setup Figure Dimensions are in millimeters and (Inches) Figure 43: Wind tunnel test setup 100LFM 2 1 0 60 65 70 75 80 85 Ambient Temperature (℃) Figure 46: DNS04S0A0R06 (Standard)Output current vs. DS_DNS04SIP06A_07172008 ambient temperature and air velocity@Vin=5V, Vo=1.5V (Either Orientation) 13 7 DNS04S0A0R06(Standard) Output Current vs. Ambient Temperature and Air Velocity @ Vin = 5.0V, Vo = 0.75V (Either Orientation) Output Current(A) 7 6 6 5 5 DNS04S0A0R06(Standard) Output Current vs. Ambient Temperature and Air Velocity @ Vin = 3.3V, Vo = 1.5V (Either Orientation) Output Current(A) 4 4 Natural Convection 3 3 2 2 1 1 Natural Convection 0 0 60 65 70 75 80 60 85 Ambient Temperature (℃) 65 70 75 80 85 Ambient Temperature (℃) Figure 47: DNS04S0A0R06 (Standard) Output current vs. Figure 49: DNS04S0A0R06 (Standard) Output current vs. ambient temperature and air velocity@Vin=5V, Vo=0.75V (Either ambient temperature and air velocity@Vin=3.3V, Vo=1.5V Orientation) (Either Orientation) 7 DNS04S0A0R06(Standard) Output Current vs. Ambient Temperature and Air Velocity @ Vin = 3.3V, Vo = 2.5V (Either Orientation) Output Current(A) 7 6 6 5 5 4 4 Natural Convectio 3 DNS04S0A0R06(Standard) Output Current vs. Ambient Temperature and Air Velocity @ Vin = 3.3V, Vo = 0.75V (Either Orientation) Output Current(A) Natural Convection 3 2 2 1 1 0 0 60 65 70 75 80 85 Ambient Temperature (℃) 60 65 70 75 80 85 Ambient Temperature (℃) Figure 48: DNS04S0A0R06 (Standard) Output current vs. Figure 50: DNS04S0A0R06 (Standard) Output current vs. ambient temperature and air velocity@Vin=3.3V, Vo=2.5V ambient temperature and air velocity@Vin=3.3V, Vo=0.75V (Either Orientation) (Either Orientation) DS_DNS04SIP06A_07172008 14 MECHANICAL DRAWING SMD PACKAGE (OPTIONAL) DS_DNS04SIP06A_07172008 SIP PACKAGE 15 PART NUMBERING SYSTEM DNS 04 S 0A0 R 06 P Product Series Input Voltage Numbers of Outputs Output Voltage Package Type Output Current On/Off logic DNS - 6A 04 - 2.8~5.5V S - Single DNM - 10A 10 –8.3~14V 0A0 R - SIP Programmable S - SMD DNL - 16A F D Option Code 06 - 6A N- negative F- RoHS 6/6 10 - 10A P- positive (Lead Free) D - Standard Function 16 - 16A MODEL LIST Model Name Packaging Input Voltage Output Voltage Output Current Efficiency 5.0Vin, 3.3Vdc @ 6A DNS04S0A0S06NFD SMD 2.8 ~ 5.5Vdc 0.75 V~ 3.3Vdc 6A 94.0% DNS04S0A0S06PFD SMD 2.8 ~ 5.5Vdc 0.75 V~ 3.3Vdc 6A 94.0% DNS04S0A0R06NFD SIP 2.8 ~ 5.5Vdc 0.75 V~ 3.3Vdc 6A 94.0% DNS04S0A0R06PFD SIP 2.8 ~ 5.5Vdc 0.75 V~ 3.3Vdc 6A 94.0% CONTACT: www.delta.com.tw/dcdc USA: Telephone: East Coast: (888) 335 8201 West Coast: (888) 335 8208 Fax: (978) 656 3964 Email: [email protected] Europe: Telephone: +41 31 998 53 11 Fax: +41 31 998 53 53 Email: [email protected] Asia & the rest of world: Telephone: +886 3 4526107 x6220 Fax: +886 3 4513485 Email: [email protected] WARRANTY Delta offers a two (2) year limited warranty. Complete warranty information is listed on our web site or is available upon request from Delta. Information furnished by Delta is believed to be accurate and reliable. However, no responsibility is assumed by Delta for its use, nor for any infringements of patents or other rights of third parties, which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Delta. Delta reserves the right to revise these specifications at any time, without notice. DS_DNS04SIP06A_07172008 16