NCV8605, NCV8606 500 mA, Low IGND, CMOS LDO Regulator with/without Enable and with Enhanced ESD Protection The NCV8605/NCV8606 provide in excess of 500 mA of output current at fixed voltage options or an adjustable output voltage from 5.0 V down to 1.25 V. These devices are designed for space constrained and portable battery powered applications and offer additional features such as high PSRR, low noise operation, short circuit and thermal protection. The devices are designed to be used with low cost ceramic capacitors and are packaged in the DFN6 3x3.3. NCV8605 is designed without enable pin, NCV8606 is designed with enable pin. Features http://onsemi.com MARKING DIAGRAM DFN6, 3x3.3 MN SUFFIX CASE 506AX • Output Voltage Options: x zzz • • • • A Y WW G • • • • • • Adjustable, 1.5 V, 1.8 V, 2.5 V, 2.8 V, 3.0 V, 3.3 V, 5.0 V Adjustable Output by External Resistors from 5.0 V down to 1.25 V Current Limit 675 mA Low IGND (Independent of Load) $1.5% Output Voltage Tolerance Over All Operating Conditions (Adjustable) $2% Output Voltage Tolerance Over All Operating Conditions (Fixed) NCV8605 Fixed is Direct Replacement LP8345 Typical Noise Voltage of 50 mVrms without a Bypass Capacitor Enhanced ESD Ratings: 4 kV Human Body Mode (HBM) 400 V Machine Model (MM) NCV Prefix for Automotive and Other Applications Requiring Site and Change Controls These are Pb−Free Devices V860x zzz AYWWG G 1 = 5 or 6 = ADJ, 150, 180, 250, 280, 300, 330, 500 = Assembly Location = Year = Work Week = Pb−Free Package (Note: Microdot may be in either location) NCV8605 PIN CONNECTIONS DFN6 3x3.3mm Vin 1 GND 2 NC 3 6 GND 5 4 Vin SENSE/ADJ Vout (Top View) Typical Applications • • • • Hard Disk Drivers Notebook Computers Battery Power Electronics Portable Instrumentation Vin Vin Cin NCV8606 PIN CONNECTIONS DFN6 3x3.3mm Vout Vout NCV8605 (Fixed) SENSE GND Cout Vin 1 GND 2 EN 3 6 GND 5 4 Vin SENSE/ADJ Vout (Top View) ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 12 of this data sheet. Figure 1. NCV8605 Typical Application Circuit for Fixed Version (1.5 V, 1.8 V, 2.5 V, 2.8 V, 3.0 V, 3.3 V, 5.0 V) © Semiconductor Components Industries, LLC, 2010 May, 2010 − Rev. 0 1 Publication Order Number: NCV8605/D NCV8605, NCV8606 Vin Vout Vout Vin NCV8606 (Fixed) Cin EN Cout SENSE GND Figure 2. NCV8606 Typical Application Circuit for Fixed Version (1.5 V, 1.8 V, 2.5 V, 2.8 V, 3.0 V, 3.3 V, 5.0 V) Vin Vout Vin Vout NCV8605 (Adjustable) Cin GND ADJ R1 Vin Vout NCV8606 (Adjustable) Cin Cout EN GND ADJ R2 Vin GND ADJ Vin Driver with Current Limit Thermal Shutdown + − NCV8606 (Adjustable) EN Vout Vout GND ADJ Cout Figure 6. NCV8606 Typical Application Circuit for Adjustable Version (Vout = 1.25 V) Vout Adjustable Version Only Vin Cin Cout Figure 5. NCV8605 Typical Application Circuit for Adjustable Version (Vout = 1.25 V) Vin Cout Figure 4. NCV8606 Typical Application Circuit for Adjustable Version (1.25 V < Vout v 5.0 V) Vout Vout NCV8605 (Adjustable) Cin R1 R2 Figure 3. NCV8605 Typical Application Circuit for Adjustable Version (1.25 V < Vout v 5.0 V) Vin Vout Vin Vin Vout Adjustable Version Only SENSE/ADJ Driver with Current Limit Thermal Shutdown Vref + − Vref EN GND GND Fixed Version Only Fixed Version Only Figure 7. NCV8605 Simplified Block Diagram Figure 8. NCV8606 Simplified Block Diagram http://onsemi.com 2 SENSE/ADJ NCV8605, NCV8606 PIN FUNCTION DESCRIPTION Pin No. Pin Name 1 Vin 2 GND 3 NC/EN 4 Vout 5 SENSE/ADJ 6 Vin EPAD GND Description Positive Power Supply Input* Power Supply Ground NCV8605: This Pin is Not Connected NCV8606: This Pin is Enable Input, Active HIGH Regulated Output Voltage Output Voltage Sense Input Fixed Version: Connect Directly to Output Capacitor Adjustable Version: Connect to Middle Point of External Resistor Divider Positive Power Supply Input* Exposed Pad is Connected to Ground *Pins 1 and 6 must be connected together externally for output current full range operation ABSOLUTE MAXIMUM RATINGS Rating Symbol Value Unit Input Voltage Range (Note 1) Vin −0.3 to 6.5 V Chip Enable Voltage Range (NCV8606 only) VEN −0.3 to 6.5 V Output Voltage Range Vout −0.3 to 6.5 V VADJ −0.3 to 6.5 V ESD 4000 400 V TJ(MAX) 150 °C TSTG −65 to 150 °C Output Voltage/Sense Input Range, SENSE/ADJ ESD Capability Human Body Model Machine Model Maximum Junction Temperature Storage Temperature Range Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. NOTE: This device series contains ESD Protection and exceeds the following tests: ESD Human Body Model tested per AEC−Q100−002 (EIA/JESD22−A114) ESD Machine Model tested per AEC− 150 mA per JEDEC standard: JESD78Q100−003 (EIA/JESD22−A115) Latchup Current Maximum Rating: v 150 mA per JEDEC standard: JESD78. 1. Minimum Vin = (Vout + VDO) or 1.5 V, whichever is higher. THERMAL CHARACTERISTICS Rating Symbol Value Unit Thermal Resistance, Junction−to−Ambient (Note 2) RqJA 75 °C/W Thermal Resistance, Junction−to−Case RYJC 18 °C/W 2. Soldered on 645 mm2, 1 oz copper area, FR4. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area. OPERATING RANGES (Note 3) Rating 3. 4. 5. 6. Symbol Value Input Voltage (Note 4) Vin 1.5 to 6.0 V Output Current (Notes 5 and 6) Iout 0 to 675 mA Junction Temperature TJ −40 to 150 °C Ambient Temperature TA −40 to 125 °C Refer to Electrical Characteristics and Application Information for Safe Operating Area. Minimum Vin = (Vout + VDO) or 1.5 V, whichever is higher. Minimum limit valid for fixed versions only. For more details refer to Application Information Section. Maximum limit for Vout = Vout(nom) − 10%. http://onsemi.com 3 Unit NCV8605, NCV8606 ELECTRICAL CHARACTERISTICS Vin = (Vout + 0.5 V) or 1.5 V, whichever is higher, Cin = 1 mF, Cout = 1 mF, for typical values TA = 25°C, for min/max values TA = −40°C to 85°C; unless otherwise noted. (Notes 9 and 10) Parameter Test Conditions Output voltage (Adjustable Version) Output voltage (Fixed Versions) Vin = 1.75 V to 6 V Iout = 1 mA to 500 mA 1.5 V Vin = (Vout + 0.5 V) to 6 V 1.8 V Iout = 1 mA to 500 mA 2.5 V 2.8 V 3.0 V 3.3 V 5.0 V Symbol Min Typ Max Unit Vout 1.231 (−1.5%) 1.250 1.269 (+1.5%) V Vout 1.470 1.764 2.450 2.744 2.940 3.234 4.900 (−2%) 1.5 1.8 2.5 2.8 3.0 3.3 5.0 1.530 1.836 2.550 2.856 3.060 3.366 5.100 (+2%) V Line regulation Vin = (Vout + 0.5 V) to 6 V, Iout = 1 mA Regline − 4 10 mV Load regulation Iout = 1 mA to 500 mA Regload − 10 30 mV Dropout voltage (Adjustable Version) (Note 9) VDO = Vin − Vout Vout = 1.25 V Iout = 500 mA − 450 470 − − − − − − − 290 250 200 190 180 170 150 360 300 250 240 230 220 200 Dropout voltage (Fixed Version) VDO VDO = Vin − (Vout − 0.1 V) 1.5 V Iout = 500 mA 1.8 V Vout = 0 V to 90% Vout(nom) 2.5 V 2.8 V 3.0 V 3.3 V 5.0 V VDO mV mV Disable Current (NCV8606 Only) (Note 10) VEN = 0 V IDIS − 0.1 1 mA Ground Current Iout = 1 mA to 500 mA IGND − 145 180 mA Current Limit (Note 11) Vout = Vout(nom) − 10 % ILIM 675 − − mA Output Short Circuit Current Vout = 0 V ISC 700 1000 1350 mA Enable Input Threshold Voltage (NCV8606 Only) Voltage Increasing, Logic High Voltage Decreasing, Logic Low Turn−on Time (Note 11) Vth(EN) High Low Vin = 0 V to (Vout + 0.5 V) or 1.75 V, 1.25 V whichever is higher 1.5 V Vout = 0 V to 90% of Vout(nom) 1.8 V 2.5 V 2.8 V 3.0 V 3.3 V 5.0 V Enable Time (NCV8606 Only) (Note 11) VEN = From 0 V to Vin 1.25 V 1.5 V 1.8 V 2.5 V 2.8 V 3.0 V 3.3 V 5.0 V ton tEN V 0.9 − − − − 0.4 − − − − − − − − 6 6 7 8 10 12 15 30 − − − − − − − − − − − − − − − − 12 12 13 16 18 19 20 30 − − − − − − − − ms ms 7. Refer to ABSOLUTE MAXIMUM RATINGS and APPLICATION INFORMATION for Safe Operating Area. 8. Performance guaranteed over the indicated operating temperature range by design and/or characterization tested at TJ = TA = 25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible. 9. Maximum dropout voltage is limited to minimum input voltage Vin = 1.7 V recommended for guaranteed operation at maximum output current. 10. Refer to application information section. 11. Values based on design and/or characterization. http://onsemi.com 4 NCV8605, NCV8606 ELECTRICAL CHARACTERISTICS Vin = (Vout + 0.5 V) or 1.5 V, whichever is higher, Cin = 1 mF, Cout = 1 mF, for typical values TA = 25°C, for min/max values TA = −40°C to 85°C; unless otherwise noted. (Notes 9 and 10) Parameter Power Supply Ripple Rejection (Note 11) Output Noise Voltage (Note 11) Test Conditions Iout = 500 mA Vout = 1.25 V Vin − Vout = 1 V f = 120 Hz, 0.5 VPP f = 1 kHz, 0.5 VPP f = 10 kHz, 0.5 VPP Symbol Min Typ Max PSRR dB − − − f = 10 Hz to 100 kHz, Vout = 1.25 V Unit 62 55 40 − − − Vn − 50 − mVrms Thermal Shutdown Temperature (Note 11) TSD − 175 − °C Thermal Shutdown Hysteresis (Note 11) TSH − 10 − °C 7. Refer to ABSOLUTE MAXIMUM RATINGS and APPLICATION INFORMATION for Safe Operating Area. 8. Performance guaranteed over the indicated operating temperature range by design and/or characterization tested at TJ = TA = 25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible. 9. Maximum dropout voltage is limited to minimum input voltage Vin = 1.7 V recommended for guaranteed operation at maximum output current. 10. Refer to application information section. 11. Values based on design and/or characterization. http://onsemi.com 5 NCV8605, NCV8606 1.267 1.264 1.261 2.55 Vout = 1.25 V Iout = 1 mA 1.258 1.255 Vin = Vout + 0.5 V = 1.75 V 1.252 1.249 1.246 Vin = 6.0 V 1.243 1.240 1.237 1.234 1.231 −40 −20 0 Vout = 2.5 V Iout = 1 mA 2.54 Vout, OUTPUT VOLTAGE (V) Vout, OUTPUT VOLTAGE (V) TYPICAL CHARACTERISTICS 20 40 60 80 100 120 2.53 2.52 2.51 Vin = Vout + 0.5 V = 3.0 V 2.50 2.49 Vin = 6.0 V 2.48 2.47 2.46 2.45 −40 140 −20 TA, AMBIENT TEMPERATURE (°C) Figure 9. Output Voltage vs. Temperature (Vout = 1.25 V) Vin = Vout + 0.5 V = 5.5 V 5.04 5.02 Vin = 6.0 V 5.00 4.98 4.96 4.94 4.92 4.90 −40 −20 0 20 40 60 80 100 120 270 100 120 140 Iout = 500 mA 210 180 Iout = 300 mA 150 120 Iout = 150 mA 90 60 30 0 −40 140 −20 0 20 40 60 80 100 120 140 TA, AMBIENT TEMPERATURE (°C) Figure 12. Dropout Voltage vs. Temperature (Vout = 2.5 V) 200 180 Vout = 5.0 V IGND, GROUND CURRENT (mA) VDO, DROPOUT VOLTAGE (mV) 80 240 TA, AMBIENT TEMPERATURE (°C) 160 140 Iout = 500 mA 120 100 Iout = 300 mA 80 Iout = 150 mA 60 40 20 0 −40 60 Vout = 2.5 V Figure 11. Output Voltage vs. Temperature (Vout = 5.0 V) 180 40 300 Vout = 5.0 V Iout = 1 mA VDO, DROPOUT VOLTAGE (mV) Vout, OUTPUT VOLTAGE (V) 5.06 20 Figure 10. Output Voltage vs. Temperature (Vout = 2.5 V) 5.10 5.08 0 TA, AMBIENT TEMPERATURE (°C) −20 0 20 40 60 80 100 120 140 170 160 Vin = Vout + 0.5 V Iout = 500 mA 150 Vout = 5.0 V 140 130 Vout = 2.5 V 120 110 Vout = 1.25 V 100 90 80 −40 TA, AMBIENT TEMPERATURE (°C) −20 0 20 40 60 80 100 120 TA, AMBIENT TEMPERATURE (°C) Figure 13. Dropout Voltage vs. Temperature (Vout = 5.0 V) Figure 14. Ground Current vs. Temperature http://onsemi.com 6 140 NCV8605, NCV8606 TYPICAL CHARACTERISTICS 80 1400 Vout = 1.25 V 70 60 Vin = 6.0 V 1200 PSRR (dB) ISC, SHORT CIRCUIT CURRENT LIMIT (mA) 1600 1000 Vin = 1.75 V 800 50 Iout = 500 mA 30 Vout = 1.25 V 20 Vin = 2.25 V Cout = 1.0 mF 10 T = 25°C A 600 400 200 −40 −20 0 20 40 60 80 100 120 0 10 140 100 TA, AMBIENT TEMPERATURE (°C) 70 1400 Vn, NOISE DENSITY (nV/√/HZ) 1600 PSRR (dB) 40 20 10 Vn = 47 mVrms 1200 60 Iout = 500 mA 100 1000 10000 100000 Vin = Vout + 0.5 V = 1.75 V Cin = Cout = 1.0 mF Iout = 500 mA TA = 25°C 1000 Iout = 1mA Vout = 2.5 V Vin = 3.5 V Cout = 1.0 mF TA = 25°C 0 10 10000 Figure 16. PSRR vs. Frequency (Vout = 1.25 V) 80 50 1000 f, FREQUENCY (Hz) Figure 15. Short Circuit Current Limit vs. Temperature (Vout = 1.25 V) 30 Iout = 1mA 40 100000 800 600 400 200 0 10 f, FREQUENCY (Hz) 100 1000 10000 100000 f, FREQUENCY (Hz) Figure 17. PSRR vs. Frequency (Vout = 2.5 V) Figure 18. Noise Density vs. Frequency (Vout = 1.25 V) Vn, NOISE DENSITY (nV/√/HZ) 2500 Vn = 70 mVrms 2000 Vin = Vout + 0.5 V = 3.0 V Cin = Cout = 1.0 mF Iout = 500 mA TA = 25°C Vout 200 mV/div Vin = 3.0 V Vout = 2.5 V Cout = 10 mF trise = tfall = 1 ms TA = 25°C 1500 1000 Iout 500 mA/div 500 0 10 100 1000 10000 100000 f, FREQUENCY (Hz) TIME (40 ms/div) Figure 19. Noise Density vs. Frequency (Vout = 2.5 V) Figure 20. Load Transient (Vout = 2.5 V) http://onsemi.com 7 NCV8605, NCV8606 TYPICAL CHARACTERISTICS Vout 100 mV/div Vout 1 V/div 4.0 V Vin 500 mV/div Vout = 2.5 V Iout = 0 mA Cout = 10 mF Vin = 2.5 V Iout = 500 mA Cout = 10 mF trise = tfall = 1 ms TA = 25°C Vin = 3.0 V trise = 1 ms TA = 25°C Vin 1 V/div 3.0 V TIME (20 ms/div) TIME (10 ms/div) Figure 21. Line Transient (Vout = 2.5 V) Figure 22. Startup Transient (Vout = 2.5 V) http://onsemi.com 8 NCV8605, NCV8606 DEFINITIONS General current are kept constant during the measurement. Results are expressed in mVrms or nV / √Hz. All measurements are performed using short pulse low duty cycle techniques to maintain junction temperature as close as possible to ambient temperature. Turn−on and Turn−off Times Turn−on Time is time difference measured during power−up of the device from the moment when input voltage reaches 90% of its operating value to the moment when output voltage reaches 90% of its nominal value at specific output current or resistive load. Turn−off Time is time difference measured during power−down of the device from the moment when input voltage drops to 10% of its operating value to the moment when output voltage drops to 10% of its nominal value at specific output current or resistive load. Line Regulation The change in output voltage for a change in input voltage. The measurement is made under conditions of low dissipation or by using pulse techniques such that the average junction temperature is not significantly affected. Load Regulation The change in output voltage for a change in output load current at a constant temperature. Dropout Voltage Enable and Disable Times The input to output differential at which the regulator output no longer maintains regulation against further reductions in input voltage. Measured when the output drops 100 mV below its nominal value. The junction temperature, load current, and minimum input supply requirements affect the dropout level. Enable Time is time difference measured during power−up of the device from the moment when enable voltage reaches 90% of input voltage operating value to the moment when output voltage reaches 90% of its nominal value at specific output current or resistive load. Disable Time is time difference measured during power−down of the device from the moment when enable voltage drops to 10% of input voltage operating value to the moment when output voltage drops to 10% of its nominal value at specific output current or resistive load. Ground and Disable Currents Ground Current is the current that flows through the ground pin when the regulator operates without a load on its output (IGND). This consists of internal IC operation, bias, etc. It is actually the difference between the input current (measured through the LDO input pin) and the output load current. If the regulator has an input pin that reduces its internal bias and shuts off the output (enable/disable function), this term is called the disable current (IDIS). Line Transient Response Typical output voltage overshoot and undershoot response when the input voltage is excited with a given slope. Load Transient Response Typical output voltage overshoot and undershoot response when the output current is excited with a given slope between no−load and full−load conditions. Current Limit and Short Circuit Current Limit Current Limit is value of output current by which output voltage drops by 10% with respect to its nominal value. Short Circuit Current Limit is output current value measured with output of the regulator shorted to ground. Thermal Protection Internal thermal shutdown circuitry is provided to protect the integrated circuit in the event that the maximum junction temperature is exceeded. When activated at typically 175°C, the regulator turns off. This feature is provided to prevent failures from accidental overheating. PSRR Power Supply Rejection Ratio is defined as ratio of output voltage and input voltage ripple. It is measured in decibels (dB). Maximum Package Power Dissipation Output Noise Voltage The power dissipation level at which the junction temperature reaches its maximum operating value. This is the integrated value of the output noise over a specified frequency range. Input voltage and output load http://onsemi.com 9 NCV8605, NCV8606 APPLICATIONS INFORMATION Noise Decoupling The NCV8605/NCV8606 regulator is self*protected with internal thermal shutdown and internal current limit. Typical application circuits are shown in Figures 1 to 4. The NCV8605/NCV8606 is a low noise regulator and needs no external noise reduction capacitor. Unlike other low noise regulators which require an external capacitor and have slow startup times, the NCV8605/NCV8606 operates without a noise reduction capacitor, has a typical 8 ms turn−on time and achieves a 50 mVrms overall noise level between 10 Hz and 100 kHz. Input Decoupling (Cin) A ceramic or tantalum 1.0 mF capacitor is recommended and should be connected close to the NCV8605/NCV8606 package. Higher capacitance and lower ESR will improve the overall line transient response. Enable Operation (NCV8606 Only) Output Decoupling (Cout) The enable pin will turn the regulator on or off. The threshold limits are covered in the electrical characteristics table in this data sheet. The turn−on/turn−off transient voltage being supplied to the enable pin should exceed a slew rate of 10 mV/ms to ensure correct operation. If the enable function is not to be used then the pin should be connected to Vin. The NCV8605/NCV8606 is a stable component and does not require a minimum Equivalent Series Resistance (ESR) for the output capacitor. The minimum output decoupling value is 1.0 mF and can be augmented to fulfill stringent load transient requirements. The regulator works with ceramic chip capacitors as well as tantalum devices. Larger values improve noise rejection and load regulation transient response. Typical characteristics were measured with Murata ceramic capacitors. GRM219R71E105K (1 mF, 25 V, X7R, 0805) and GRM21BR71A106K (10 mF, 10 V, X7R, 0805). Output Voltage Adjust The output voltage can be adjusted from 1 times (Figure 4) to 4 times (Figure 3) the typical 1.250 V regulation voltage via the use of resistors between the output and the ADJ input. The output voltage and resistors are chosen using Equation 1 and Equation 2. No−Load Regulation Considerations The NCV8605/NCV8606 adjustable regulator will operate properly under conditions where the only load current is through the resistor divider that sets the output voltage. However, in the case where the NCV8605/NCV8606 is configured to provide a 1.250 V output, there is no resistor divider. If the part is enabled under no−load conditions, leakage current through the pass transistor at junction temperatures above 85°C can approach several microamps, especially as junction temperature approaches 150°C. If this leakage current is not directed into a load, the output voltage will rise up to a level approximately 20 mV above nominal. The NCV8605/ NCV8606 contains an overshoot clamp circuit to improve transient response during a load current step release. When output voltage exceeds the nominal by approximately 20 mV, this circuit becomes active and clamps the output from further voltage increase. Tying the ENABLE pin to Vin (NCV8606 only) will ensure that the part is active whenever the supply voltage is present, thus guaranteeing that the clamp circuit is active whenever leakage current is present. When the NCV8606 adjustable regulator is disabled, the overshoot clamp circuit becomes inactive and the pass transistor leakage will charge any capacitance on Vout. If no load is present, the output can charge up to within a few millivolts of Vin. In most applications, the load will present some impedance to Vout such that the output voltage will be inherently clamped at a safe level. A minimum load of 10 mA is recommended. Unlike LP8345, for NCV8605/606 fixed voltage versions there is no limitation for minimum load current. ǒ V out + 1.250 1 ) R2 ^ Ǔ R1 R2 ) ǒI ADJ R 1Ǔ (eq. 1) R1 V out 1.25 *1 (eq. 2) Input bias current IADJ is typically less than 150 nA. Choose R1 arbitrarily to minimize errors due to the bias current and to minimize noise contribution to the output voltage. Use Equation 2 to find the required value for R2. Thermal As power in the NCV8605/NCV8606 increases, it might become necessary to provide some thermal relief. The maximum power dissipation supported by the device is dependent upon board design and layout. Mounting pad configuration on the PCB, the board material, and the ambient temperature affect the rate of junction temperature rise for the part. When the NCV8605/NCV8606 has good thermal conductivity through the PCB, the junction temperature will be relatively low with high power applications. The maximum dissipation the NCV8605/NCV8606 can handle is given by: P D(MAX) + ƪTJ(MAX) * TAƫ (eq. 3) R QJA Since TJ is not recommended to exceed 125°C (TJ(MAX)), then the NCV8605/NCV8606 soldered on 645 mm2, 1 oz copper area, FR4 can dissipate up to 1.3 W when the ambient http://onsemi.com 10 NCV8605, NCV8606 Hints temperature (TA) is 25°C. See Figure 23 for RqJA versus PCB area. The power dissipated by the NCV8605/NCV8606 can be calculated from the following equations: P D [ V inǒI GND@I OUTǓ ) I outǒV in * V outǓ Vin and GND printed circuit board traces should be as wide as possible. When the impedance of these traces is high, there is a chance to pick up noise or cause the regulator to malfunction. Place external components, especially the output capacitor, as close as possible to the NCV8605/NCV8606, and make traces as short as possible. (eq. 4) or V in(MAX) [ P D(MAX) ) ǒV out I outǓ (eq. 5) I out ) I GND 250 RqJA, (°C/W) 200 150 FR4 = 1.0 oz 100 FR4 = 2.0 oz 50 0 0 200 400 COPPER AREA 600 800 (mm2) Figure 23. Thermal Resistance vs. Copper Area http://onsemi.com 11 NCV8605, NCV8606 ORDERING INFORMATION Device Nominal Output Voltage (V) Marking Package Shipping† NCV8605MNADJT2G ADJ V8605 ADJ DFN6 (Pb−Free) 3000 / Tape & Reel NCV8605MN15T2G 1.5 V8605 150 DFN6 (Pb−Free) 3000 / Tape & Reel NCV8605MN18T2G 1.8 V8605 180 DFN6 (Pb−Free) 3000 / Tape & Reel NCV8605MN25T2G 2.5 V8605 250 DFN6 (Pb−Free) 3000 / Tape & Reel NCV8605MN28T2G 2.8 V8605 280 DFN6 (Pb−Free) 3000 / Tape & Reel NCV8605MN30T2G 3.0 V8605 300 DFN6 (Pb−Free) 3000 / Tape & Reel NCV8605MN33T2G 3.3 V8605 330 DFN6 (Pb−Free) 3000 / Tape & Reel NCV8605MN50T2G 5.0 V8605 500 DFN6 (Pb−Free) 3000 / Tape & Reel NCV8606MNADJT2G ADJ V8606 ADJ DFN6 (Pb−Free) 3000 / Tape & Reel NCV8606MN15T2G 1.5 V8606 150 DFN6 (Pb−Free) 3000 / Tape & Reel NCV8606MN18T2G 1.8 V8606 180 DFN6 (Pb−Free) 3000 / Tape & Reel NCV8606MN25T2G 2.5 V8606 250 DFN6 (Pb−Free) 3000 / Tape & Reel NCV8606MN28T2G 2.8 V8606 280 DFN6 (Pb−Free) 3000 / Tape & Reel NCV8606MN30T2G 3.0 V8606 300 DFN6 (Pb−Free) 3000 / Tape & Reel NCV8606MN33T2G 3.3 V8606 330 DFN6 (Pb−Free) 3000 / Tape & Reel NCV8606MN50T2G 5.0 V8606 500 DFN6 (Pb−Free) 3000 / Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 12 NCV8605, NCV8606 PACKAGE DIMENSIONS DFN6 3x3.3 MM, 0.95 PITCH CASE 506AX−01 ISSUE O A D PIN 1 REFERENCE 2X 0.15 C 2X 0.15 C DATE 20 JAN 2006 NOTES: 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.25 AND 0.30 mm FROM TERMINAL. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. B ÇÇÇ ÇÇÇ ÇÇÇ ÇÇÇ E DIM A A1 A3 b D D2 E E2 e K L L1 TOP VIEW 0.10 C A 6X 0.08 C (A3) SIDE VIEW D2 6X C A1 SEATING PLANE SOLDERING FOOTPRINT* 4X 3.60 e L 1 K 3 MILLIMETERS MIN NOM MAX 0.80 −−− 0.90 0.00 −−− 0.05 0.20 REF 0.30 −−− 0.40 3.00 BSC 1.90 −−− 2.10 3.30 BSC 1.10 −−− 1.30 0.95 BSC 0.20 −−− −−− 0.40 −−− 0.60 0.00 −−− 0.15 1.35 6X 0.50 1 E2 6X L1 2.15 6 0.95 PITCH 4 6X BOTTOM VIEW b (NOTE 3) 0.10 C A B 6X 0.83 0.05 C DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/ Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 http://onsemi.com 13 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NCV8605/D