SS-222 R12 12/6/06 10:36 AM Page 1 SS-222 R12 AHA 12/06/06 Multilayer Ceramic Inductors Type MHL CERTIFIED CERTIFIED 1. General ■ ■ ■ ■ ■ Monolithic structure provides high reliability in a wide temperature and humidity range High quality ceramic material and unique manufacturing process provides high Q at high frequency Standard EIA packages: 1E, 1J Nickel barrier with solder overcoat for excellent solderability Marking: Brown body color with no marking (1E) White body color with with black stripe and no marking (1J) 2. Dimensions L t L Solder Plating Ni Plating 1E (0402) .039±.004 (1.0±0.1) .02±.004 (0.5±0.1) .02±.004 (0.5±0.1) .01±.004 (0.25±0.1) Silver Metallization 1J (0603) .063±.006 (1.6±0.15) .031±.006 (0.8±0.15) .031±.006 (0.8±0.15) .012±.008 (0.30±0.2) d Terminations (Metallization Bands) d Dimensions inches (mm) W t Size Code W d Electrodes 3. Type Designation The type designation shall be in the following form: MHL 1E C T TE 3N9 S Type Size Material Termination Material Packaging Nominal Inductance Tolerance 1E 1J Permeability Code: C T T: Sn (Other termination styles available, contact factory for options) TP: 7" paper tape 2mm pitch (1E only - 10,000 pcs/reel) TD: 7" paper tape (1J - 4,000 pcs/reel 3N9 = 3.9nH R10 = 100nH S: ±0.3nH J: ±5% PAGE 1 OF 6 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Spec ific ation s given herein m ay be c hang ed at an y tim e w itho ut prior not ice. Plea se co nfirm t echn ic al spec ific ations b efore yo u orde r and/ or us e. SS-222 R12 12/6/06 10:36 AM Page 2 SS-222 R12 4. Standard Applications NEW Part Designation Inductance L (nH) MHL1ECTTP1N0* MHL1ECTTP1N2* MHL1ECTTP1N5* MHL1ECTTP1N8* MHL1ECTTP2N2* MHL1ECTTP2N7* MHL1ECTTP3N3* MHL1ECTTP3N9* MHL1ECTTP4N7* MHL1ECTTP5N6* MHL1ECTTP6N8* MHL1ECTTP8N2* MHL1ECTTP10N* MHL1ECTTP12N* MHL1ECTTP15N* MHL1ECTTP18N* MHL1ECTTP22N* MHL1ECTTP27N* MHL1ECTTP33N* MHL1ECTTP39N* MHL1ECTTP47N* MHL1ECTTP56N* MHL1ECTTP68N* MHL1ECTTP82N* MHL1ECTTPR10* 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 56 68 82 100 MHL1ECTTPR12* MHL1JCTTD1N5* MHL1JCTTD1N8* MHL1JCTTD2N2* MHL1JCTTD2N7* MHL1JCTTD3N3* MHL1JCTTD3N9* MHL1JCTTD4N7* MHL1JCTTD5N6* MHL1JCTTD6N8* MHL1JCTTD8N2* MHL1JCTTD10N* MHL1JCTTD12N* MHL1JCTTD15N* MHL1JCTTD18N* MHL1JCTTD22N* MHL1JCTTD27N* MHL1JTTTD27N* MHL1JCTTD33N* 120 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 27 33 Inductance Tolerance Self Resonant Frequency Minimum Typical Typical Typical (100MHz) (100MHz) (800MHz) (MHz) 37 10000 36 Q S: ±0.3nH 34 3900 3500 3200 2600 2300 2000 1600 1400 1200 1100 900 750 1.4 600 1.6 6000 4000 8 31 30 J: ±5% 28 26 24 23 21 19 16 –– 10 Allowable DC Current Maximum (mA) Operating Temperature Range 0.12 0.13 0.14 0.16 0.17 0.19 0.22 0.24 0.27 0.32 0.37 0.42 0.50 0.55 0.65 0.8 0.9 1.0 1.2 1.3 32 11 DC Resistance Maximum () –– 300 -55°C to +125°C 200 180 150 100 0.10 8 S: ±0.3nH 6000 14 10 100 5800 3200 2600 2300 2000 1600 0.13 0.15 0.20 0.23 0.20 0.28 0.30 0.35 0.40 0.45 0.50 1400 0.55 1200 0.60 4000 46 15 J: ±5% 12 18 15 -55°C to +125°C 600 500 *Add tolerance character (S, J) PAGE 2 OF 6 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Spec ific ation s given herein m ay be c hang ed at an y tim e w itho ut prior not ice. Plea se co nfirm t echn ic al spec ific ations b efore yo u orde r and/ or us e. SS-222 R12 12/6/06 10:36 AM Page 3 SS-222 R12 4. Standard Applications (continued) Part Designation Inductance L (nH) MHL1JCTTD39N* MHL1JTTTD39N* MHL1JCTTD47N* MHL1JCTTD56N* MHL1JCTTD68N* MHL1JCTTD82N* MHL1JCTTDR10* MHL1JCTTDR12* MHL1JCTTDR15* MHL1JCTTDR18* MHL1JCTTDR22* 39 39 47 56 68 82 100 120 150 180 220 Inductance Tolerance Self Resonant Frequency Minimum Typical Typical Typical (100MHz) (100MHz) (800MHz) (MHz) Q 15 17 46 39 37 36 29 12 15 J: ±5% 16 8 13 — 1100 DC Resistance Maximum () Allowable DC Current Maximum (mA) Operating Temperature Range 0.65 0.70 0.75 0.80 0.85 0.90 1.0 1.2 1.3 1.5 900 700 600 500 400 500 400 -55°C to +125°C 300 *Add tolerance character (S, J) PAGE 3 OF 6 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Spe cific at io ns given herein m ay be chan ged at an y tim e w ith out prior not ice. P le ase co nfirm t ech nical spec ific ation s before y ou orde r and/ or us e. SS-222 R12 12/6/06 10:36 AM Page 4 SS-222 R12 5. Characteristics Item Requirement Conditions Operating Temperature -55°C to +125°C Storage Temperature 40°C @ 70% Humidity Sealed plastic bags with desiccant shall be used to reduce the potential of oxidation on the terminations during storage. Resistance to Solder Heat Change in Impedance: Relative to value before test ±20%. Appearance: There shall be no cracking Solder Coverage: More than 75% of the terminal electrode shall be covered with solder. Flux: 5-10 sec dip After Flux: Air dry for 15 sec Preheat: 150°C ±10°C Preheat Time: 60 sec Solder Temp: 260°C ±5°C Dip Time: 10 ±1 sec Solderability Solder Coverage: More than 95% of the termination shall be covered with solder. Flux: 5-10 sec dip After Flux: Air dry for 15 sec Solder Temp: 245°C ±5°C Dip Time: 5 ±0.5 sec Leach Resistance Appearance: There shall be no visible signs of physical or mechanical damage (i.e. no cracks) Terminations: Termination must not be leached away for more than 5%. The bead shall be subjected to the following 5 steps for the period of time shown below. The 5 steps constitute one (1) rotation. 4 rotations shall be carried out. 1) Flux: 5-10 sec 2) After Flux: Air dry for 15 sec 3) Solder Temp: 230°C ±5°C 4) Dip Time: 5 ±0.5 sec 5) Cool: Air cool for 60 seconds Insulation Resistance Insulation Resistance: Min 1G ohms Solvent Resistance Change in Impedance: Relative to value before test ±10%. Terminal Strength (hanging test) Appearance: The terminal electrode shall not break off, nor shall there be damage to the body. Type 1E 1J W(kgf) –– 0.5 Time N/A 30 sec ±2 sec Terminal Strength (push test) Appearance: There shall be no evidence of mechanical degradations to terminals or body. Type 1E 1J W(kgf) –– 1.4 Time N/A 60 sec Bending Strength Appearance: There shall be no physical or mechanical damage Impedance: Relative to initial value before test ±10% Cleaning by: Washer: Ultrasonic washer (100W) Solvent: Isopropyl alcohol Time: 3 minutes Board: 90x40x1.6mm Bend: 1mm Time: 5 sec PAGE 4 OF 6 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Spec ific ation s given herein m ay be c hang ed at an y tim e w itho ut prior not ice. Plea se co nfirm t echn ic al spec ific ations b efore yo u orde r and/ or us e. SS-222 R12 12/6/06 10:36 AM Page 5 SS-222 R12 5. Characteristics (continued) Item Requirement Conditions Mechanical Shock Appearance: There shall be no physical or mechanical damage Impedance: Relative to initial value before test ±10% Force: 50G Time: 11 msec There shall be 3 shocks in each of 6 directions (18 shocks total). Vibration Impedance: Relative to initial value ±10% Only endurance conditioning by sweeping shall be made. The entire frequency range from 10-2,000 Hz and return to 10 Hz in 20 minutes (this shall constitute one cycle). Amplitude: 15G The test shall have a 15G peak and shall be applied for a period of 4 hours (12 cycles) in each of 3 mutually perpendicular directions (a total of 36 cycles within a total of 12 hours). Thermal Shock Appearance: There shall be no physical or mechanical damage. Impedance: Relative to initial value ±20%. DCR: The DCR shall not exceed initial specified value. Testing of the parts will be made at 0 hours, 250 hours and 500 hours. Before testing the parts shall be allowed to cool to room temperature for 24 hours. Load Humidity Appearance: There shall be no physical or mechanical damage Impedance: Relative to initial value ±15% Step 1-start 2-hold 3-transfer 4-hold 5-transfer Temperature -40°C ±2°C -40°C ±2°C — +105°C ±2°C — Time — 30 min ±5 min 0.5 min max. 30 min ±5 min 0.5 min max. Steps 1 thru 5 constitute one complete cycle and the test shall consist of a total of 500 cycles. Temperature: 85°C ±2°C Relative Humidity: 85% Time: 1,000 hours total Apply: 100% rated current Measurements shall be taken at 0 hours, 250 hours, 500 hours and 1,000 hours and shall meet the conditions stated above. Life Test Appearance: There shall be no physical or mechanical damage Impedance: Relative to initial value ±15% Temperature: 85°C ±2°C Time: 1,000 hours total Apply: 100% rated current Measurements shall be taken at 0 hours, 250 hours, 500 hours and 1,000 hours and shall meet the conditions stated above. 6. Packaging Specifications KOA’s multilayer components are provided on tape-and-reel for use in pick-and-place machines. The reel size is 7 inch. PAGE 5 OF 6 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Spec ific ation s given herein m ay be c hang ed at an y tim e w itho ut prior not ice. Plea se co nfirm t echn ic al spec ific ations b efore yo u orde r and/ or us e. SS-222 R12 12/6/06 10:36 AM Page 6 SS-222 R12 7. Dimensions - inches (mm) Do Tape Ao Bo Ko 1E .026±.004 (0.67±0.1) .046±.004 (1.17±0.1) .025±.004 (0.63±0.1) .045±.004 (1.15±0.1) .073±.004 (1.85±0.1) .043±.004 (1.1±0.1) 1J P2 Po E W F Bo D1 Tape E F W P1 Po 1E 1J .069±.004 (1.75±0.10) .138±.002 (3.5±.005) .315±.008 (8.0±0.2) .079±.009 (2.0±0.23) .079±.004 (2.0±0.1) 8. Chip Quantities Per Reel Ao P1 P2 Ko Do .079±.002 .059±.004 (2.0±0.05) (1.5+0.1/-0.0) D1 t .039 min. (1.0 min.) .009±.001 (0.23±0.02) 9. Recommended PC Board Land Patterns - inches (mm) Parts on 7 inch Parts on 13 inch (178mm) Reel (330mm) Reel Chip Size t 0402 (1005) 10,000 –––––– 0603 (1608) 4,000 4,000 Chip Size L G H 1E (0402) .05 (1.3) .015 (0.4) .019 (0.5) 1J (0603) .102 (2.6) .023 (0.6) .031 (0.8) H G L 10. Recommended Temperature Profiles for Soldering Recommended Temperature Profile for Wave Soldering Preheat 100 Seconds Max. Soldering 10 Seconds Max. Natural Cooling Recommended Temperature Profile for Reflow Soldering Preheat 100 Seconds Max. 250°C Soldering 10 Seconds Max. Natural Cooling 230°C 200°C 150°C 150°C 60 Seconds Max. 20 Seconds Max. 60 Seconds Max. PAGE 6 OF 6 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Spec ific ation s given herein m ay be c hang ed at an y tim e w itho ut prior not ice. Plea se co nfirm t echn ic al spec ific ations b efore yo u orde r and/ or us e.