Series AM10TW-Z 10 Watt | DC-DC Converter FEATURES: Ultra Wide 4:1 input range Efficiency up to 88% RoHS compliant Continuous Short Circuit Protection • • • • Models Single output Model Input Voltage (V) AM10TW-2403SZ AM10TW-2405SZ AM10TW-2412SZ AM10TW-2415SZ AM10TW-4803SZ AM10TW-4805SZ AM10TW-4812SZ AM10TW-4815SZ 9-36 9-36 9-36 9-36 18-75 18-75 18-75 18-75 Model Input Voltage (V) AM10TW-2405DZ AM10TW-2412DZ AM10TW-2415DZ AM10TW-4805DZ AM10TW-4812DZ AM10TW-4815DZ 9-36 9-36 9-36 18-75 18-75 18-75 Operating temperature -40oC to + 85oC Remote on/off control Input/Output Isolation 1600VDC Over voltage & Over Load Protection Output Voltage (Vdc) Output Current max (mA) Isolation (VDC) 2700 2000 833 667 2700 2000 833 667 1600 1600 1600 1600 1600 1600 1600 1600 Output Voltage (V) Output Current max (mA) Isolation (VDC) 3.3 5 12 15 3.3 5 12 15 Models Dual output • • • • ±5 ±12 ±15 ±5 ±12 ±15 ±1000 ±417 ±330 ±1000 ±417 ±330 1600 1600 1600 1600 1600 1600 Max Capacitive Load(uF) Efficiency (%) 1330 1330 288 200 1330 1330 288 200 85 87 88 88 84 87 87 87 Max Capacitive Load(uF) Efficiency (%) ±900 ±133 ±90 ±900 ±133 ±90 85 87 87 85 88 88 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Voltage range Filter Start up time Absolute Maximum Rating Peak Input Voltage time On/Off control Input reflected current Isolation Specifications Parameters Tested I/O voltage Resistance Capacitance www.aimtec.com F 051e R12.C Nominal Typical 24 48 9-36 18-75 Maximum Units VDC π (Pi) Network Nominal Vin and constant resistive load 20 24 Vin -0.7-50 48 Vin -0.7-100 ms VDC 100 ms ON – High (3.0 ... 12Vdc) or open circuit; OFF – Low (0 ... 1.2Vdc) or Short circuit pin1 and pin 2/3 OFF idle current: 5.0 mA typical 20 mAPk-Pk Conditions Typical 3 sec >1000 1500 Tel: +1 514 620 2722 1 of 3 Rated 1600 Units VDC MOhm pF Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM10TW-Z 10 Watt | DC-DC Converter Output Specifications Parameters Conditions Voltage accuracy Typical ±1.2 ±5 25% load on one output 100% load on second load Cross Regulation (Dual Output Models) Over voltage protection Over current protection Short Circuit protection Short circuit restart Line voltage regulation Load voltage regulation (Single) Load voltage regulation (Dual) Temperature coefficient Ripple & Noise Minimum Load Current Zener diode clamp 170 Continuous Auto recovery ±2 ±0.5 ±1.0 ±0.02 85 0 Full Load HL-LL 0% Load to Full Load 0% Load to Full Load 20MHz Bandwidth General Specifications Parameters Switching frequency Operating temperature Storage temperature Maximum case temperature Derating Cooling Humidity Case material Potting material Weight Dimensions (L x W x H) MTBF Maximum soldering temperature Transient recovery time Transient recovery deviation Conditions 100% load Full Load with derating above 60ºC Above 60ºC Maximum Typical -40 to +125 270 -40 to +85 Free air convection 2.5 Units % % % % % % %/oC mV p-p % of Max Maximum 105 95 Nickel-coated Copper UL94V-0 rated 18 1.25 x 0.80 x 0.40 inches 31.75 x 20.32 x 10.16 mm >1 000 000 hrs (MIL-HDBK -217F, Ground Benign, t=+25oC) 1.5mm from case for 10 sec 260 250 ±3 Units KHz o C o C o C %/ oC % RH g o C uS % Safety Specifications Parameters Agency approvals Standards CE EN55022 Class A IEC61000-4-2, Perf. Criteria B IEC61000-4-3, Perf. Criteria A IEC61000-4-4, Perf. Criteria B (external 330uF/100V cap required) IEC61000-4-5, Perf. Criteria B (external 330uF/100V cap required) IEC61000-4-6, Perf. Criteria A IEC61000-4-8, Perf. Criteria A NOTE: Also designed to meet standard IEC 60950-1: 2001 Pin Out Specifications Pin 1 2 3 9 11 14 16 22 23 Single Remote On/Off -V Input -V Input No Pin N.C. +V Output -V Output +V Input +V Input www.aimtec.com F 051e R12.C Dual Remote On/Off -V Input -V Input Common -V Output +V Output Common +V Input +V Input Tel: +1 514 620 2722 2 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM10TW-Z 10 Watt | DC-DC Converter Dimensions 22.90 (0.90) 0.50 (0.02) 20.30 (0.80) 0.50 (0.02) 1 2 3 11 9 Bottom View 23 22 16 14 5.08 (0.20) 2.54 (0.10) Printed Face 15.20 (0.60) 31.80 (1.25) 3.05 (0.12) 10.20 (0.40) All dimensions are typical: millimeters (inches) Pin Diameter: 0.50 ± 0.05 (0.02 ± 0.002) Pin Pitch Tolerance: ± 0.35 (±0.014) Case Tolerence: ± 0.5 (±0.02) Derating Free Air Convection 60ºC 100 80 60 Safe Operating Area 40 20 0 - 40 - 20 0 20 40 60 80 85 100 Ambient Temperature º C Recommended Circuit Surge/EFT Conducted Emissions L C1 +Vin DC/DC Converter C2 -Vin C1 2.2uF, 100V +Vin +Vout L 12uH DC/DC Converter C1 Load +Vout Load -Vin -Vout -Vout C2 2.2uF, 100V NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R12.C Tel: +1 514 620 2722 3 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only