MQAC & MQAT Series Same Day Shipping Available Full-Size (14Pin Dip) CMOS/TTL Output Wide Frequency Range Frequency 1.000MHZ to 150.000MHZ Frequency Stability (Inclusive of Temperature, Load & Voltage) See Part Number Guide Aging @ +25°C ±5 ppm per year max Operating Temperature Range See Part Number Guide -55°C to +125°C Storage Temperature Range Output Waveform TTL Supply Voltage (Vdd) Supply Current (unloaded) Load CMOS +3.3 VDC ±10% +5.0 VDC ±10% +3.3 VDC ±10% +5.0 VDC ±10% 25mA 45mA 25mA 45mA 10 TTL or 50pF 15pF 5TTL or 30pF 30pF Logic “0” 0.4V max 0.4V max Logic “1” 2.4 V min Vdd-0.4V min Rise/Fall Time 4nSec max Start Up Time 10mSec max Duty Cycle Jitter Tri-State Operation 1.000MHZ to 66.000MHZ 45%/55% (TTL @ 1.4V Level / CMOS @ 50% Waveform) 66.000MHZ and above 40%/60% (TTL @ 1.4V Level / CMOS @ 50% Waveform) 1.000MHZ to 33.000MHZ 50pSec max (RMS) 50pSec max (RMS) 33.000MHZ and above 30pSec max (RMS) 40pSec max (RMS) Voh = 70% of Vdd min or No Connection to Enable Output Vol = 30% of Vdd max or grounded to Disable Output (High Impedance) Environmental & Mechanical Detail Marking Detail Line 1 = MXXXXX Shock MIL-STD-883, Method 2002 Cond B Solderability MIL-STD-883, Method 2003 Solvent Resistance MIL-STD-202, Method 215 Vibration MIL-STD-883, Method 2007, Cond A M = MMD XXXXX = Frequency in MHZ S = YYWW = L = Internal Code 4 Numerical Digit Date Code (Year / Week) Denotes RoHS Compliant Line 2 = SYYWWL Line 3 = XXXXX Internal use only Gross Leak Test MIL-STD-883, Method 1014, Cond C May vary with lots Pin 1 Designator MMD Monitor/Quartztek 30400 Esperanza, Rancho Santa Margarita, CA, 92688 Phone: (949) 709-5075, Fax: (949) 709-3536, www.mmdcomp.com [email protected] Revision: Subject to change without notice 05/03/11 C Pg 1 of 2 Part Number Guide MQA H FREQUENCY Full-size (14 pin DIP) Output C = CMOS T = TTL Frequency Stability 020 = ±20 ppm 025 = ±25 ppm 050 = ±50 ppm 100 = ±100 ppm Supply Voltage 5 = +5 VDC 3 = +3.3 VDC Operating Temperature Blank = 0°C to +70°C 27 = -20°C to +70°C 48 = -40°C to +85°C Pin 1 Connection H = Tri-state Value Added Options Blank = No Added Options G1 = Gull-Wing (option 1) G = Gull-Wing (option 2) CLXXX = Cut Leads XXX = Lead Length Code PLEASE CONSULT WITH MMD SALES DEPARTMENT FOR ANY OTHER PARAMETERS OR OPTIONS Mechanical Details 20.70 [.815] 15.24 [.600] 20.70 [.815] MAX 13.10 [.516] MAX 5.08 [.200] MXXXXX SYYWWL XXXXX 7.62 [.300] 5.08 [.200] MIN PIN CONNECTIONS PIN 1 TRI-STATE PIN 7 GROUND PIN 8 OUTPUT PIN 14 SUPPLY VOLTAGE .50 [.020] DIMENSIONS IN BRACKET ARE IN INCHES EXTERNAL BYPASS CAPACITOR RECOMMENDED Tape & Reel Dimensions PITCH Tape Width Q1 Q2 Q1 Q2 Q3 Q4 Q3 Q4 REEL DIA PITCH TAPE WIDTH REEL DIA PIN 1 ORIENT. 12.00 [.471] 24.00 [.945] 330 [13.0] Q1 DIRECTION OF FEED NOTES: UNLESS OTHERWISE SPECIFIED 1. Applicable Standards / Specifications ANSI Y14.5M, Dimensions and Tolerances EIA-481-B, 8 mm through 200mm Embossed Carrier Taping and 8 mm and 12 mm Punched Carrier Taping of Surface Mount Components for Automatic Handling. 2. Dimensions are in millimeters [inch]. 3. Tolerances are ±0.1 [.004] mm unless otherwise specified. 4. Do not scale drawing. MMD Monitor/Quartztek 30400 Esperanza, Rancho Santa Margarita, CA, 92688 Phone: (949) 709-5075, Fax: (949) 709-3536, www.mmdcomp.com [email protected] Revision: Subject to change without notice 05/03/11 C Pg 2 of 2