XP Power JPS250PS12C 200 w / 300 w with convection cooling Datasheet

ACDC
250/350 Watts
xppower.com
JPS250/350 Series
•
200 W / 300 W with Convection Cooling
•
High Efficiency up to 88%
•
Meets 1U, Low Profile Requirements
•
AC OK & DC OK Signals
•
Zero Voltage Switching Technology
•
Remote On/Off & Remote Sense
•
3 Year Warranty
Specification
Input
General
• 85-264 VAC (170-370 VDC)
• 47-63 Hz
• 2.75 A/1.40 A max at 115 VAC/ 230 VAC (JPS250)
4.5 A/2.2 A max at 115 VAC/230 VAC (JPS350)
Inrush Current
• 30 A at 115 VAC, 60 A at 230 VAC
Power Factor
• 0.9 typical
Earth Leakage Current • 3.0 mA max 264 VAC/60 Hz
Input Protection
• Internal T5 A, 250 VAC fuse (JPS250)
Internal T6.3 A, 250 VAC fuse (JPS350)
Input Voltage
Input Frequency
Input Current
Efficiency
Isolation
Switching Frequency
Power Density
Signals
MTBF
Output
• See tables
• ±10% on output 1 only (VR1)
• At 60% rated load ±1% on V1 & V2,
±5% on V3 & V4
Minimum Load
• Single output models: No minimum load
required. Multi-output models, see note 4
Start Up Delay
• 2 s typical
Start Up Rise Time
• 80 ms typical (JPS250)
100 ms typical (JPS350)
Hold Up Time
• 20 ms min at low line & rated load
Line Regulation
• ±0.5% at rated load across input voltage range
Load Regulation
• ±1% for single output models & V1 & V2 of
multi-output models, ±5% for V3 & V4
Transient Response
• 4% max deviation, recovery to within
1% in 500 µs for a 25% load change
Ripple & Noise
• ±1% max pk-pk, 15 MHz bandwidth,
see note 2 under model tables
Overvoltage Protection • 115-140% on single outputs & V1 of quad
output models, recycle input to reset
Overtemperature
• Shuts down at +110 °C, auto recovery,
Protection
measured internally
Overload Protection
• 110-130% of max rated load on all O/Ps,
auto recovery
Short Circuit Protection • Trip and restart (Hiccup mode), auto
recovery
Temp. Coefficient
• ±0.05%/°C
Remote Sense
• Compensates for up to 0.5 V drop
Output Voltage
Output Voltage Trim
Initial Set Accuracy
Remote On/Off
Current Share
Fan Output
• On = Logic Low or Open, Off = Logic High
• Current share on single output models & V1
& V2 of multi-output models (4 supplies can
be paralleled)
• See mechanical notes for ordering information
• Up to 88%
• 3000 VAC Input to Output
1500 VAC Input to Ground
500 VAC Output to Ground
• 120 kHz typical for PFC and PWM
• 4.96 W/In3
• AC OK, DC OK, Remote On/Off
(see control and supervisory signals)
• 125 kHrs to MIL-HDBK-217F
at +50 °C, GB (JPS250)
146 kHrs to MIL-HDBK-217F
at +50 °C, GB (JPS350)
Environmental
Operating Temperature • 0 °C to +70 °C, (see derating curve)
Full power to +50 °C
Cooling
• 250 W with 18 CFM airflow (JPS250)
200 W convection cooling (JPS250)
350 W with 18 CFM airflow (JPS350)
300 W convection cooling (JPS350)
Operating Humidity
• 5-95% RH, non-condensing
Storage Temperature • -20 °C to +85 °C
Operating Altitude
• 2000 m
Vibration
• 2 g, 10 Hz to 55 Hz, 30 mins each axis
EMC & Safety
Emissions
Harmonic Currents
ESD Immunity
Radiated Immunity
EFT/Burst
Surge
Dips and Interruptions
Safety Approvals
• EN55022, level B conducted
FCC 20780, level B conducted
• EN61000-3-2
• EN61000-4-2, level 3 Perf Criteria A
• EN61000-4-3, 10 V/m Perf Criteria A
• EN61000-4-4, level 3 Perf Criteria A
• EN61000-4-5, level 3 Perf Criteria A
• EN61000-4-11, 30% 10 ms, 60% 100 ms,
100% 5000 ms, Perf Criteria A, B, B
• EN60950-1, UL60950-1,
CSA C22.2 No. 60950-1, CE Mark LVD
Output
Power(1)
Convection-cooled
18 CFM
225 W
250 W
Output Current
Output
Voltage
Ripple & Noise
Pk-Pk
Model
Number(3)
5V
36.0 A
45.0 A
50 mV
JPS250PS05C
12 V
17.0 A
21.0 A
120 mV
JPS250PS12C
15 V
13.5 A
17.0 A
120 mV
JPS250PS15C
24 V
8.5 A
10.4 A
200 mV
JPS250PS24C
48 V
4.3 A
5.2 A
200 mV
JPS250PS48C
Notes
1. Maximum power with 18 CFM forced air is 250 W, or 200 W with convection cooling.
2. Ripple and noise measured over 15 MHz bandwidth with a 0.47 µF capacitor.
3. For non-current share version delete suffix ‘C’ from model number.
Mechanical Details
All models (except JPS250PS05)
8.00 (203.2)
A
B
B
L
Pin
A
VR1
10
TB4
Voltage Adj.
N
2
E
TB1
1
+
-
TB3
1
3.75
(95.3)
4.20
(106.7)
TB2
TRANSFORMER
6
A
B
B
A
5.50 (139.0)
6.50 (165.1)
0.30
(7.6)
0.75
(19.1)
TB4
All models
1
+5 V
+V
Signal 0 V
2
+5 V
+V
DC OK
3
0V
+V
AC OK
4
0V
0V
Remote On/Off
5
0V
0V
+Sense
6
0V
0V
7
+5 V
Current Share(5)
8
+5 V
N/C
-Sense
9
N/C
10
N/C
7.40 (188.0)
A
A
B
B
1.51
(38.3)
JPS250PS05
8.00 (203.2)
A
VR1
B
2
10
TB4
Voltage Adj.
L
1
N
1
E
TB1
4.20
(106.7)
TB2
TRANSFORMER
TB3
A
+
-
1.30 (32.1)
5.50 (139.0)
0.70 (19.1)
6.50 (165.1)
Fixing Holes:
A = #6-32 screw mounting holes
B = M3 x 0.5 screw mounting holes
Maximum mounting screw penetration is 0.16 (4.0) from chassis
outer surface.
8
B
B
Notes
1. TB3 is for fan, with Molex 5045-02A or equivalent.
5 V model: 5 V at 390 mA, 24 V model: 24 V at 80 mA,
all other models: 12 V at 112 mA
2. TB1 (AC input) and TB2 (DC output) are terminal blocks.
3. TB4 signal connector is Molex 70246-10 or equivalent.
4. Fan cover option available, order part number:
5 V models: JPS250 F/CVR 5
12, 15 & 48 V models: JPS250 F/CVR
24 V models: JPS250 F/CVR 24
Or add suffix ‘-E’ to model number to receive unit with
fan cover fitted. 4.2 x 8 x 2.48 (106.7 x 203.2 x 62.9).
5. For current share operation connect current share (pin 7) between
units. For non ‘C’ models pin 7 (current share) is not used.
6. Input and output terminal screw tightening torque 9 lbs-in (1.0 Nm)
maximum.
0.36
(9.1)
3.75
(95.3)
PIN CONNECTIONS
TB2
JPS250PS05
All other models
A
All dimensions are in inches (mm)
Tolerance: ±0.03 (0.8) max
Weight: 1.65 lbs (750 g) approx.
ACDC
JPS250 Single Output
Models and Ratings
ACDC
JPS250 Multi Output
Models and Ratings
Output 1
Output 2
Output
V1
Conv.
Cooled
Max
18 CFM
3.3 V
16.0 A
5.0 V
17.5 A
5.0 V
5.0 V
Output 3
Output
V2
Conv.
Cooled
Max
18 CFM
20 A
5V
12 A
30 A
12 V
7A
20.0 A
25 A
12 V
20.0 A
25 A
15 V
Output 4
Model
Number(3)
Output
V3
Conv.
Cooled
Max
18 CFM
Output
V4
Conv.
Cooled
Max
18 CFM
20 A
12 V
5A
6A
-12 V
1A
2A
JPS250PQ46C
8A
-12 V
2A
3A
-5 V
1A
2A
JPS250PQ41C
4A
6A
24 V
2A
3A
-12 V
1A
2A
JPS250PQ47C
3A
5A
24 V
2A
3A
-15 V
1A
2A
JPS250PQ48C
Notes
1.
2.
3.
4.
Maximum power with 18 CFM forced air is 250 W, or 200 W with convection cooling.
Ripple and noise measured over 15 MHz bandwidth with a 0.47 µF capacitor.
For non current share option delete suffix ‘C’ from model number.
All models require 2 A minimum load on V1. On V2, JPS250PQ46 requires 1 A and JPS250PQ41 requires 0.5 A.
† Available from Farnell. See pages 266-269.
^ Available from Newark. See pages 270-272.
Mechanical Details
8.00 (203.2)
L
1
N
Voltage Adj.
E
TB3
TRANSFORMER
TB1
10
2
VR1
TB2
VR2
8
1
4.20
(106.7)
Safety earth connection
+
-
0.30
(7.6)
0.75
(19.1)
TB5
A
A
B
B
1
2
3
4
5
6
7
8
9
10
+5 V
+5 V
0V
0V
0V
-5 V
-12 V
+12 V
Pin
PQ41
1
2
3
4
5
6
7
8
9
10
+5 V +S
+5 V PS(5)
+12 V +S
DC OK
+12 V -S
+5 V -S
+12 V PS(5)
Remote On/Off
AC OK
0V
1.30 1.50
(33.1) (38.1)
0.36
(9.1)
8.00 (203.2)
B
B
A
B
B
A
3.75
(95.3)
1.30 (32.1)
0.70
(19.1)
A
PQ41
PIN CONNECTIONS - TB3
PQ46
PQ47
+12 V
-12 V
+5 V
+5 V
0V
0V
0V
0V
+3.3 V
+3.3 V
+5 V
+5 V
0V
0V
0V
-12 V
+24 V
+12 V
PQ48
+5 V
+5 V
0V
0V
0V
-15 V
+24 V
+15 V
0.16 (4.0)
7.40 (187.9)
A
Pin
PIN CONNECTIONS - TB2
PQ46
PQ47
+3.3 V +S
+5 V -S
+3.3 V PS(5)
DC OK
+5 V +S
+3.3 V -S
+5 V PS(5)
Remote On/Off
AC OK
0V
+5 V +S
+5 V PS(5)
+12 V +S
DC OK
+12 V -S
+5 V -S
+12 V PS(5)
Remote On/Off
AC OK
0V
PQ48
+5 V +S
+5 V PS(5)
+15 V +S
DC OK
+15 V -S
+5 V -S
+15 V PS(5)
Remote On/Off
AC OK
0V
Notes
0.22
(5.7)
5.50 (139.0)
6.50 (165.1)
Fixing Holes:
A = #6-32 screw mounting holes
B = M3 x 0.5 screw mounting holes
Maximum mounting screw penetration is 0.16 (4.0) from chassis outer surface.
All dimensions are in inches (mm).
Tolerance: ±0.03 (0.8) max.
Weight: 1.65 lbs (750 g) approx.
1. TB5 is for fan with Molex 5045-02A or equivalent. 12 V at 112 mA.
2. TB1 (AC input) and TB3 (DC output) are terminal blocks.
3. TB2 signal connector is Molex 70246-10 or equivalent.
4. Fan cover option available, order part number:
PQ41, PQ46 & PQ47: JPS250 F/CVR PQ48: JPS250 F/CVR 24
or add suffix ‘-E’ to model number to receive unit with fan cover fitted.
4.2 x 8 x 2.48 (106.7 x 203.2 x 62.9).
5. PS - Current share on ‘C’ models only.
No connection on standard models.
6. VR2 is for production setting only.
7. Input terminal screw tightening torque 9 lbs-in (1.0 Nm) maximum.
8. Output terminal screw tightening torque 4 lbs-in (0.45 Nm) maximum.
Output
Power
Output Current
Output
Voltage
315 W
350 W
Convection-cooled
18 CFM
Ripple & Noise
Pk-Pk(2)
Model
Number(1)
5V
54.0 A
63.0 A
50 mV
JPS350PS05C
12 V
25.0 A
30.0 A
120 mV
JPS350PS12C
15 V
20.0 A
24.0 A
120 mV
JPS350PS15C
24 V
13.0 A
15.0 A
200 mV
JPS350PS24C
48 V
6.5 A
7.3 A
200 mV
JPS350PS48C
Notes
1. For non-current share version delete suffix ‘C’ from model number.
2. Ripple and noise measured over 15 MHz bandwidth with a 47 µF electrolytic capacitor and 0.47 µF ceramic capacitor.
† Available from Farnell. See pages 266-269.
^ Available from Newark. See pages 270-272.
Mechanical Details
All models (except JPS350PS05)
Pin
9.00 (228.6)
A
L
A
B
B
N
1
E
TB1
4.50
(114.3)
5.00
(127.0)
TRANSFORMER
6
TB2
10
2
Voltage Adj.
A
1
+
TB3
TB4
A
B
B
VR1
0.25
(6.75)
0.75
(19.1)
6.50 (164.4)
1
+5 V
+V
2
+5 V
+V
N/C
N/C
3
0V
+V
+Remote sense
4
0V
0V
DC OK
5
0V
0V
-Remote sense
6
0V
0V
7
+5 V
Current Share(5)
8
+5 V
Remote On/Off
N/C
9
AC OK
10
0V
8.00 (203.2)
A
A
B
B
1.60
(40.6)
0.47
(12.0)
JPS350PS05
9.00 (228.6)
A
B
B
A
1. TB3 is for fan, with Molex 5045-02A or equivalent. 12 V at 112 mA
(except JPS350PS05, 5 V at 390 mA).
2. TB1 (AC input) and TB2 (DC output) are terminal blocks.
3. TB4 signal connector is Molex 70246-10 or equivalent.
4. Fan cover option available, order part number:
5 V models: JPS350 F/CVR 5
All other models: JPS350 F/CVR
Alternatively, add suffix ‘-E’ to model number to receive fan cover fitted
to the unit 4.95 x 8.92 x 2.48 (127.0 x 228.6 x 62.9).
5. For current share operation, connect current share (pin 7) between
units. For non ‘C’ models pin 7 is not used.
6. Input and output terminal screw tightening torque 9 lbs-in (1.0 Nm)
maximum.
TB4
VR1
N
Notes
12
Voltage Adj.
L
10
E
1
TB1
TRANSFORMER
4.50
(114.3)
5.00
(127.0)
Fixing Holes:
A = #6-32 screw mounting holes
B = M3 x 0.5 screw mounting holes
Maximum mounting screw penetration is 0.16 (4.0) from chassis
outer surface.
8
TB3
A
0.25
(6.75)
TB4
All models
7.50 (190.5)
0.50
(12.7)
0.87
(22.0)
PIN CONNECTIONS
TB2
JPS350PS05
All other models
0.75
(19.1)
B
+ 6.50 (164.4)
7.50 (190.5)
TB2
B
A
All dimensions are in inches (mm)
Tolerance: ±0.03 (0.8) max.
Weight: 2.12 lbs (960 g) approx.
ACDC
JPS350 Single Output
Models and Ratings
ACDC
JPS250/350
Control & Supervisory Signals
AC OK Signal
DC OK Signal
+5 V
+5 V
330 R
330 R
AC OK (HIGH)
DC OK (HIGH)
AC OK
DC OK
GND
GND
DC NOT OK (LOW)
AC NOT OK (LOW)
AC OK is a TTL signal which goes LOW when input falls out of
specification. Source current is 1 mA, sink current is 6 mA.
DC OK is a TTL signal which goes LOW when PSU is in an overcurrent
condition, overvoltage condition, disabled or when output falls out of regulation.
Source current is 1 mA, sink current is 6 mA.
Remote On/Off Control (Inhibit)
Parallel Connection Utilizing Optional Current Share
Supply 1
OUTPUTS OFF (5V)
Remote On/Off
Output
Return
Current Share
V1
Ground
OUTPUTS ON (0 V or open circuit)
Supply 2
Output
Return
Current Share
To turn off the output, apply 5 V to the remote On/Off.
Remote Sense Connection
Output
+
Sense
+
CD
+
Twisted Pair
Supply
LOAD
CL
Sense
-
Output
-
CD
Notes:
1. CD is 0.1 µF ceramic capacitor.
LOAD
Return
2. CL i s 47 µF electrolytic capacitor.
Derating Curve
100
90
80
L
O 70
A 60
D 50
40
%) 30
20
10
0
JPS250PS with 18 CFM Fan
JPS250PS Convection-cooled
0
10
20
30
40
50
Ambient Temperature (˚C)
60
70
80
60
70
80
JPS350 with 18 CFM Fan
100
90
80
L
O 70
A 60
D 50
40
(%) 30
20
10
0
JPS350 Convection-cooled
0
10
20
30
40
50
Ambient Temperature (°C)
Cover Option
See mechanical details notes for ordering information.
1.70 (43.2)
2.48 (62.9)
Typical internal clearance
0.15 (3.8)
4 x M3 x 6 C/S head fixing screws
in existing countersunk holes
11-Apr-11
ACDC
JPS250/350
Control & Supervisory Signals
Similar pages