Panasonic DSKTJ08 Silicon n-channel junction fet for af impedance converter Datasheet

DSKTJ08
Tentative
Total pages
page
DSKTJ08
Silicon N-channel junction FET
For AF impedance converter
Marking Symbol : CT, CU
Package Code : TSSSMini3-F2-B
Absolute Maximum Ratings
Parameter
Drain-source voltage(Gate open)
Drain-gate voltage(Source open)
Drain-source current(Gate open)
Drain-gate current(Source open)
power dissipation
Operating ambient temperature
Storage temperature
Electrical Characteristics
Parameter
Drain current
*1,*4
Drain-source current
Symbol
Rating
Unit
VDSO
VDGO
IDSO
IDGO
PD
Topr
Tstg
20
20
2
2
100
-20 to +80
-55 to +150
V
V
mA
mA
mW
°C
°C
*4
*2
Voltage gain
Voltage gain difference
Voltage gain difference
*3
Pin name
1. Drain
2. Source
3. Gate
Ta = 25 °C±3 °C
Symbol
Conditions
VDD = 2.0 V, Rd = 2.2 kΩ ± 1%
VDD = 2.0 V, Rd = 2.2 kΩ ± 1%,
IDSS
VGS = 0
gm
VDS = 2.0 V, VGS = 0, f = 1 kHz
VDD = 2.0 V, Rd = 2.2 kΩ ± 1%
NV
Co = 5 pF, A-curve
VDD = 2.0 V, Rd = 2.2 kΩ ± 1%
GV1
Co = 5 pF, eG = 10 mV, f = 1 kHz
VDD = 1.5 V, Rd = 2.2 kΩ ± 1%
GV2
Co = 5 pF, eG = 10 mV, f = 1 kHz
VDD = 2.0 V, Rd = 2.2 kΩ ± 1%
Δ | GV・f | Co = 5 pF, eG = 10 mV
f = 1 kHz to 70 Hz
ID
Mutual conductance
Noise voltage
Ta = 25 °C
Min
Max
Unit
180
470
μA
190
460
μA
660 1 500
μS
10
-5.0
-1.0
-7.0
-1.5
μV
dB
0
0
|GV1-GV2|
Typ
1.7
2.0
Note: 1. Measuring methods are based on JAPANESE INDUSTRIAL STANDARD JIS C 7030 Measuring
methods for transistors.
2. A protection diode is built-in between gate and source of transistor. However if forward current
flows between gate and source transistor might be damaged. So please be careful not insert reverse.
3. *1 ID is assured for IDSS.
*2 NV is assured for design.
*3 Δ|GV . f | is assured for AQL 0.065. (The measurement method is used by source-grounded circuit.)
*4 Rank classification
Code
T
U
Packing
Rank
T
ID
180 to 320
IDSS
190 to 310
Marking symbo
CT
280
290
U
to 470
to 460
CU
Embossed type (Thermo-compression sealing) : 10 000 pcs / reel
2010.05.31
2010.7.29
Prepared
Revised
Semiconductor Company,Panasonic Corporation
TSSSMini3-F2-B
Unit: mm
+0.05
+0.05
0.33 −0.02
0.08 −0.02
2
1
+0.05
0.15 min.
5°
1.20 ±0.05
0.80 ±0.05
3
0.23 −0.02
(0.40)
(0.40)
0.80 ±0.05
1.20 ±0.05
0.33 max.
0.01 ±0.01
0.15 max.
5°
Request for your special attention and precautions in using the technical information and
semiconductors described in this book
(1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and
regulations of the exporting country, especially, those with regard to security export control, must be observed.
(2) The technical information described in this book is intended only to show the main characteristics and application circuit examples
of the products. No license is granted in and to any intellectual property right or other right owned by Panasonic Corporation or any
other company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any
other company which may arise as a result of the use of technical information described in this book.
(3) The products described in this book are intended to be used for general applications (such as office equipment, communications
equipment, measuring instruments and household appliances), or for specific applications as expressly stated in this book.
Consult our sales staff in advance for information on the following applications:
– Special applications (such as for airplanes, aerospace, automotive equipment, traffic signaling equipment, combustion equipment,
life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of
the products may directly jeopardize life or harm the human body.
It is to be understood that our company shall not be held responsible for any damage incurred as a result of or in connection with
your using the products described in this book for any special application, unless our company agrees to your using the products in
this book for any special application.
(4) The products and product specifications described in this book are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product
Standards in advance to make sure that the latest specifications satisfy your requirements.
(5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions
(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute
maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any
defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure
mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire
or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.
(6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,
thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which
damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.
(7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of our company.
20100202
Similar pages