LM4992, LM4992SDBD www.ti.com SNAS220B – NOVEMBER 2003 – REVISED MAY 2013 LM4992 420mW Stereo Cell Phone Audio Amplifier Check for Samples: LM4992, LM4992SDBD FEATURES DESCRIPTION • • • • The LM4992 is a stereo audio power amplifier primarily designed for demanding applications in mobile phones and other portable communication device applications. It is capable of delivering 1 watt, per channel, of continuous average power to an 8Ω BTL load with less than 1% distortion (THD+N) from a 5VDC power supply. 1 2 • • • • Available in Space-Saving WSON Package Ultra Low Current Shutdown Mode BTL Output Can Drive Capacitive Loads Improved Click and Pop Circuitry Eliminates Noise During Turn-On and Turn-Off Transitions 2.2 - 5.5V Operation No Output Coupling Capacitors, Snubber Networks or Bootstrap Capacitors Required Unity-Gain Stable External Gain Configuration Capability APPLICATIONS • • • The LM4992 features independent shutdown control for each channel and a low-power consumption shutdown mode, which is achieved by driving both shutdown pins with logic low. Additionally, the LM4992 features an internal thermal shutdown protection mechanism. Mobile Phones PDAs Portable Electronic Devices KEY SPECIFICATIONS • • • • Boomer audio power amplifiers were designed specifically to provide high quality output power with a minimal amount of external components. The LM4992 does not require output coupling capacitors or bootstrap capacitors, and therefore is ideally suited for mobile phone and other low voltage applications where minimal power consumption is a primary requirement. Improved PSRR at 217Hz & 1KHz: 64 dB (1KHz) Stereo Output Power at 5.0V, 1% THD, 8Ω: 1.07 W (typ) Stereo Output Power at 3.3V, 1% THD, 8Ω: 420 mW (typ) Shutdown Current, Vdd = 3.3V: 0.2 µA (typ) The LM4992 contains advanced click and pop circuitry which eliminates noise which would otherwise occur during turn-on and turn-off transitions. The LM4992 is unity-gain stable and can be configured by external gain-setting resistors. Connection Diagram 14 Pin WSON (Top View) See Package Number NHK0014A 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2003–2013, Texas Instruments Incorporated LM4992, LM4992SDBD SNAS220B – NOVEMBER 2003 – REVISED MAY 2013 www.ti.com TYPICAL APPLICATION V DD Cs 1 PF Rf 20k Audio Input Ri 20k -IN Ci 0.39 PF +IN Vo1 + - 20 k: RL 20 k: 8: Bypass V IH Shutdown Shutdown Control Shutdown BIAS Shutdown Control V IH Bypass VIL + + Vo1 BIAS CB 1.0 PF V IL A V = -1 V DD /2 VDD /2 + CB 1.0 PF Vo2 A V = -1 + - RL 20 k: +IN Audio Input + Ri 20k -IN Ci 0.39 PF 8: 20 k: Vo2 - GND Rf 20k Figure 1. Typical Audio Amplifier Application Circuit These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 2 Submit Documentation Feedback Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LM4992 LM4992SDBD LM4992, LM4992SDBD www.ti.com SNAS220B – NOVEMBER 2003 – REVISED MAY 2013 ABSOLUTE MAXIMUM RATINGS Supply Voltage (1) (2) (3) 6.0V −65°C to +150°C Storage Temperature −0.3V to VDD +0.3V Input Voltage Power Dissipation (4) (5) ESD Susceptibility (6) ESD Susceptibility (7) Internally Limited 2000V 200V Junction Temperature Thermal Resistance (1) (2) (3) (4) (5) (6) (7) 150°C θJA (WSON) 103°C/W Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication of device performance. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. If the product is in Shutdown mode and VDD exceeds 6V (to a max of 8V VDD), then most of the excess current will flow through the ESD protection circuits. If the source impedance limits the current to a max of 10mA, then the device will be protected. If the device is enabled when VDD is greater than 5.5V and less than 6.5V, no damage will occur, although operation life will be reduced. Operation above 6.5V with no current limit will result in permanent damage. The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, θJA, and the ambient temperature TA. The maximum allowable power dissipation is PDMAX = (TJMAX–TA)/θJA or the number given in Absolute Maximum Ratings, whichever is lower. Maximum power dissipation in the device (PDMAX) occurs at an output power level significantly below full output power. PDMAX can be calculated using Equation (1) shown in the APPLICATION INFORMATION section. It may also be obtained from the power dissipation graphs. Human body model, 100pF discharged through a 1.5kΩ resistor. Machine Model, 220pF–240pF discharged through all pins. OPERATING RATINGS TMIN ≤ TA ≤ TMAX Temperature Range −40°C ≤ TA ≤ 85°C 2.2V ≤ VDD ≤ 5.5V Supply Voltage Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LM4992 LM4992SDBD Submit Documentation Feedback 3 LM4992, LM4992SDBD SNAS220B – NOVEMBER 2003 – REVISED MAY 2013 www.ti.com ELECTRICAL CHARACTERISTICS VDD = 5V (1) (2) The following specifications apply for the circuit shown in Figure 1, unless otherwise specified. Limits apply for TA = 25°C. Symbol Parameter LM4992 Conditions Typical 14 mA (max) 7 18 mA (max) 1.4 3 µA (max) Shutdown Current VSDIH Shutdown Voltage Input High 1.5 VSDIL Shutdown Voltage Input Low 1.3 VOS Output Offset Voltage Po Output Power TWU Wake-up time THD+N Total Harmonic Distortion+Noise Xtalk Crosstalk (3) (4) (5) Units (Limits) 6 ISD (1) (2) (4) (5) VIN = 0V, Io = 0A, 8Ω Load Quiescent Power Supply Current Power Supply Rejection Ratio Limit VIN = 0V, Io = 0A, No Load IDD PSRR (3) VSD = VGND V V 7 30 mV (max) THD = 1% (max); f = 1 kHz, per channel 1.07 0.9 W (min) 100 ms Po = 0.5 Wrms; f = 1kHz 0.15 % 80 dB Vripple = 200mV sine p-p Input terminated with 10Ω 60 (f = 217Hz) 64 (f = 1kHz) 55 dB (min) All voltages are measured with respect to the ground pin, unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication of device performance. Typicals are measured at 25°C and represent the parametric norm. Limits are ensured to AOQL (Average Outgoing Quality Level). Datasheet min/max specification limits are specified by design, test, or statistical analysis. ELECTRICAL CHARACTERISTICS VDD = 3.3V (1) (2) The following specifications apply for the circuit shown in Figure 1, unless otherwise specified. Limits apply for TA = 25°C. Symbol Parameter LM4992 Conditions Typical 12 mA (max) 5 15 mA (max) 0.2 2.0 µA (max) Shutdown Current VSDIH Shutdown Voltage Input High 1.2 VSDIL Shutdown Voltage Input Low 1.0 VOS Output Offset Voltage Wake-up time THD+N Total Harmonic Distortion+Noise Xtalk Crosstalk PSRR (1) (2) (3) (4) (5) 4 Power Supply Rejection Ratio Units (Limits) 4 ISD TWU (4) (5) VIN = 0V, Io = 0A, 8Ω Load Quiescent Power Supply Current Output Power Limit VIN = 0V, Io = 0A, No Load IDD Po (3) VSD = VGND 7 V V 30 mV (max) THD = 1% (max); f = 1 kHz, per channel 420 mW (min) 75 ms Po = 0.25 Wrms; f = 1kHz 0.1 % 80 dB Vripple = 200mV sine p-p Input terminated with 10Ω 65 (f = 217Hz) 70 (f = 1kHz) 55 dB (min) All voltages are measured with respect to the ground pin, unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication of device performance. Typicals are measured at 25°C and represent the parametric norm. Limits are ensured to AOQL (Average Outgoing Quality Level). Datasheet min/max specification limits are specified by design, test, or statistical analysis. Submit Documentation Feedback Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LM4992 LM4992SDBD LM4992, LM4992SDBD www.ti.com SNAS220B – NOVEMBER 2003 – REVISED MAY 2013 ELECTRICAL CHARACTERISTICS VDD = 2.6V (1) (2) The following specifications apply for the circuit shown in Figure 1, unless otherwise specified. Limits apply for TA = 25°C. Symbol Parameter LM4992 Conditions Typical VIN = 0V, Io = 0A, No Load 4.0 VIN = 0V, Io = 0A, 8Ω Load 6.0 VSD = VGND 0.02 IDD Quiescent Power Supply Current ISD Shutdown Current VSDIH Shutdown Voltage Input High 1.2 VSDIL Shutdown Voltage Input Low 1.0 VOS Output Offset Voltage Po Output Power TWU Wake-up time THD+N Total Harmonic Distortion+Noise Xtalk Crosstalk PSRR (1) (2) (3) (4) (5) (3) 5 Power Supply Rejection Ratio Limit (4) (5) Units (Limits) mA (max) mA (max) 2.0 µA (max) V V 30 mV (max) THD = 1% (max); f = 1 kHz, per channel 240 70 ms Po = 0.15 Wrms; f = 1kHz 0.1 % 80 dB Vripple = 200mV sine p-p Input terminated with 10Ω 51 (f = 217Hz) 51 (f = 1kHz) dB (min) mW (min) All voltages are measured with respect to the ground pin, unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication of device performance. Typicals are measured at 25°C and represent the parametric norm. Limits are ensured to AOQL (Average Outgoing Quality Level). Datasheet min/max specification limits are specified by design, test, or statistical analysis. External Components Description (Figure 1) Components Functional Description 1. Ri Inverting input resistance which sets the closed-loop gain in conjunction with Rf. This resistor also forms a high pass filter with Ci at fC= 1/(2π RiCi). 2. Ci Input coupling capacitor which blocks the DC voltage at the amplifiers input terminals. Also creates a highpass filter with Ri at fc = 1/(2π RiCi). Refer to the section, PROPER SELECTION OF EXTERNAL COMPONENTS, for an explanation of how to determine the value of Ci. 3. Rf Feedback resistance which sets the closed-loop gain in conjunction with Ri. 4. CS Supply bypass capacitor which provides power supply filtering. Refer to the POWER SUPPLY BYPASSING section for information concerning proper placement and selection of the supply bypass capacitor. 5. CB Bypass pin capacitor which provides half-supply filtering. Refer to the section, PROPER SELECTION OF EXTERNAL COMPONENTS, for information concerning proper placement and selection of CB. Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LM4992 LM4992SDBD Submit Documentation Feedback 5 LM4992, LM4992SDBD SNAS220B – NOVEMBER 2003 – REVISED MAY 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICs THD+N vs Frequency at VDD = 3.3V, 8Ω RL, and PWR = 250mW, per channel 20 20 10 10 5 5 2 2 THD + N (%) THD + N (%) THD+N vs Frequency at VDD = 5V, 8Ω RL, and PWR = 500mW, per channel 1 0.5 0.2 1 0.5 0.2 0.1 0.1 0.05 0.05 0.02 0.02 0.01 20 50 100 200 500 1k 2k 0.01 20 5k 10k 20k 50 100 200 500 1k 2k FREQUENCY (Hz) Figure 2. Figure 3. THD+N vs Frequency at VDD = 2.6V, 8Ω RL, and PWR = 150mW, per channel THD+N vs Power Out at VDD = 5V, 8Ω RL, 1kHz, per channel 20 20 10 10 5 5 2 2 THD + N (%) THD + N (%) FREQUENCY (Hz) 1 0.5 0.2 1 0.5 0.2 0.1 0.1 0.05 0.05 0.02 0.02 0.01 20 50 100 200 500 1k 2k 0.01 10m 20m 5k 10k 20k Figure 4. Figure 5. THD+N vs Power Out at VDD = 3.3V, 8Ω RL, 1kHz, per channel THD+N vs Power Out at VDD = 2.6V, 8Ω RL, 1kHz, per channel 20 20 10 10 5 5 2 2 THD + N (%) THD + N (%) 50m 100m 200m 500m 1 0.5 0.2 1 0.2 0.1 0.05 0.05 0.02 0.02 0.01 10m 0.01 10m 50m 100m 200m 500m 1 OUTPUT POWER (W) 20m 50m 100m 200m 500m 1 OUTPUT POWER (W) Figure 6. Submit Documentation Feedback 2 0.5 0.1 20m 1 OUTPUT POWER (W) FREQUENCY (Hz) 6 5k 10k 20k Figure 7. Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LM4992 LM4992SDBD LM4992, LM4992SDBD www.ti.com SNAS220B – NOVEMBER 2003 – REVISED MAY 2013 TYPICAL PERFORMANCE CHARACTERISTICs (continued) +0 -5 -10 -15 -20 -25 -30 -35 -40 -45 -50 -55 -60 -65 -70 -75 -80 Power Supply Rejection Ratio (PSRR) vs Frequency at VDD = 5V, 8Ω RL +0 -10 -20 -30 LEVEL (dB) LEVEL (dB) Power Supply Rejection Ratio (PSRR) vs Frequency at VDD = 5V, 8Ω RL -40 -50 -60 -70 -80 -90 -100 20 50 100 200 500 1k 2k 5k 10k 20k 20 FREQUENCY (Hz) 50 100 200 500 1k 2k 5k 10k 20k FREQUENCY (Hz) Figure 9. Input Floating Power Supply Rejection Ratio (PSRR) vs Frequency at VDD = 3.3V, 8Ω RL Power Supply Rejection Ratio (PSRR) vs Frequency at VDD = 3.3V, 8Ω RL +0 -5 -10 -15 -20 -25 -30 -35 -40 -45 -50 -55 -60 -65 -70 -75 -80 +0 -10 -20 -30 LEVEL (dB) LEVEL (dB) Figure 8. Input terminated with 10Ω -40 -50 -60 -70 -80 -90 -100 20 50 100 200 500 1k 2k 5k 10k 20k 20 FREQUENCY (Hz) 50 100 200 500 1k 2k 5k 10k 20k FREQUENCY (Hz) Figure 11. Input Floating Power Supply Rejection Ratio (PSRR) vs Frequency at VDD = 2.6V, 8Ω RL Power Supply Rejection Ratio (PSRR) vs Frequency at VDD = 2.6V, 8Ω RL +0 -5 -10 -15 -20 -25 -30 -35 -40 -45 -50 -55 -60 -65 -70 -75 -80 +0 -10 -20 -30 LEVEL (dB) LEVEL (dB) Figure 10. Input Floating -40 -50 -60 -70 -80 -90 -100 20 50 100 200 500 1k 2k 5k 10k 20k 20 FREQUENCY (Hz) 50 100 200 500 1k 2k 5k 10k 20k FREQUENCY (Hz) Figure 12. Input terminated with 10Ω Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LM4992 LM4992SDBD Figure 13. Input Floating Submit Documentation Feedback 7 LM4992, LM4992SDBD SNAS220B – NOVEMBER 2003 – REVISED MAY 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICs (continued) Open Loop Frequency Response, 3.3V 70 180 o 70 180o 60 135o 60 135o o 50 90o 50 90 40 45 30 o 0 o 20 -45 10 -90o PHASE 0 100 1k 10k 100k 1M GAIN (dB) GAIN o PHASE GAIN (dB) GAIN 40 45o 30 0o 20 -45o -90o 10 PHASE -135 o -180 o PHASE Open Loop Frequency Response, 5V -135o 0 -180o 10M 100 1k 10k 100k 1M 10M FREQUENCY (Hz) FREQUENCY (Hz) Figure 14. Figure 15. Open Loop Frequency Response, 2.6V Noise Floor, 5V, 8Ω 80kHz Bandwidth, Input to GND 60 135o 50 90o 40 45o GAIN 30 0o 20 -45o 10 -90o PHASE -135o 0 -180o 100 1k 10k 100k 1M 90P OUTPUT NOISE VOLTAGE (V) 180o PHASE GAIN (dB) 100P 70 80P 70P 60P 50P 40P 30P 20P 10P 0 20 10M FREQUENCY (Hz) Figure 17. Crosstalk vs Frequency 5V, 8Ω, POUT = 1W Crosstalk vs Frequency 3.3V, 8Ω, POUT = 400mW +0 +0 -10 -10 -20 -20 OUTPUT LEVEL (dB) OUTPUT LEVEL (dB) 5k 10k 20k FREQUENCY (Hz) Figure 16. -30 -40 -50 -60 -70 -30 -40 -50 -60 -70 -80 -80 -90 -90 -100 -100 20 50 100 200 500 1k 2k 5k 10k 20k 20 FREQUENCY (Hz) Submit Documentation Feedback 50 100 200 500 1k 2k 5k 10k 20k FREQUENCY (Hz) Figure 18. 8 50 100 200 500 1k 2k Figure 19. Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LM4992 LM4992SDBD LM4992, LM4992SDBD www.ti.com SNAS220B – NOVEMBER 2003 – REVISED MAY 2013 TYPICAL PERFORMANCE CHARACTERISTICs (continued) Crosstalk vs Frequency 2.6V, 8Ω, POUT = 200mW Power Dissipation vs Output Power, 5V, 8Ω, per channel 700 +0 POWER DISSIPATION (mW) -10 OUTPUT LEVEL (dB) -20 -30 -40 -50 -60 -70 -80 600 500 400 300 200 100 -90 0 -100 20 50 100 200 500 1k 2k 0 5k 10k 20k 200 400 600 800 1000 1200 OUTPUT POWER (mW) FREQUENCY (Hz) Figure 20. Figure 21. Power Dissipation vs Output Power, 3.3V, 8Ω, per channel Power Dissipation vs Output Power, 2.6V, 8Ω, per channel 180 300 POWER DISSIPATION (mW) POWER DISSIPATION (mW) 160 250 200 150 100 50 140 120 100 80 60 40 20 0 0 0 100 200 300 400 500 600 700 0 50 OUTPUT POWER (mW) 150 200 250 300 350 Figure 22. Figure 23. Shutdown Hysteresis Voltage 5V Shutdown Hysteresis Voltage 3.3V 2.5 SUPPLY CURRENT/CHANNEL (mA) SUPPLY CURRENT/CHANNEL (mA) 3.5 100 OUTPUT POWER (mW) 3 2.5 2 SD OFF (play) SD ON 1.5 1 0.5 0 2 1.5 SD OFF (play) SD ON 1 0.5 0 0 0.5 1 1.5 2 2.5 3 3.5 0 SHUTDOWN VOLTAGE (V) Figure 24. 0.5 1 1.5 2 2.5 3 3.5 SHUTDOWN VOLTAGE (V) Figure 25. Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LM4992 LM4992SDBD Submit Documentation Feedback 9 LM4992, LM4992SDBD SNAS220B – NOVEMBER 2003 – REVISED MAY 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICs (continued) Shutdown Hysteresis Voltage 2.6V Output Power vs Supply Voltage, 8Ω 1750 1500 2 OUTPUT POWER (mW) SUPPLY CURRENT/CHANNEL (mA) 2.5 1.5 SD OFF (play) SD ON 1 0.5 1250 10% THD + N 1000 750 1% THD + N 500 250 0 0 0 0.5 1 1.5 2 2.5 3 2 3.5 2.5 SHUTDOWN VOLTAGE (V) 3 3.5 4 4.5 Figure 26. Figure 27. Frequency Response vs Input Capacitor Size Wakeup Time vs Supply Voltage +1 -0 CB = 1 PF 100 0.39 PF WAKEUP TIME (ms) OUTPUT LEVEL (dB) 5.5 120 0.1 PF -1 -2 5 SUPPLY VOLTAGE (V) -3 -4 -5 -6 -7 -8 CB = 0.68 PF 80 60 CB = 0.47 PF 40 CB = 0.22 PF 20 -9 -10 20 0 50 100 200 500 1k 2k 5k 10k 20k 2 FREQUENCY (Hz) Submit Documentation Feedback 3 3.5 4 4.5 5 5.5 SUPPLY VOLTAGE (V) Figure 28. 10 2.5 Figure 29. Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LM4992 LM4992SDBD LM4992, LM4992SDBD www.ti.com SNAS220B – NOVEMBER 2003 – REVISED MAY 2013 APPLICATION INFORMATION BRIDGE CONFIGURATION EXPLANATION As shown in Figure 1, the LM4992 has two internal operational amplifiers per channel. The first amplifier's gain is externally configurable , while the second amplifier is internally fixed in a unity-gain, inverting configuration. The closed-loop gain of the first amplifier is set by selecting the ratio of Rf to Ri while the second amplifier's gain is fixed by the two internal 20kΩ resistors. Figure 1 shows that the output of amplifier one serves as the input to amplifier two which results in both amplifiers producing signals identical in magnitude, but out of phase by 180°. Consequently, the differential gain for the IC is AVD= 2 *(Rf/Ri) (1) By driving the load differentially through outputs Vo1 and Vo2, an amplifier configuration commonly referred to as “bridged mode” is established. Bridged mode operation is different from the classical single-ended amplifier configuration where one side of the load is connected to ground. A bridge amplifier design has a few distinct advantages over the single-ended configuration, as it provides differential drive to the load, thus doubling output swing for a specified supply voltage. Four times the output power is possible as compared to a single-ended amplifier under the same conditions. This increase in attainable output power assumes that the amplifier is not current limited or clipped. In order to choose an amplifier's closedloop gain without causing excessive clipping, please refer to the AUDIO POWER AMPLIFIER DESIGN section. A bridge configuration, such as the one used in LM4992, also creates a second advantage over single-ended amplifiers. Since the differential outputs, Vo1 and Vo2, are biased at half-supply, no net DC voltage exists across the load. This eliminates the need for an output coupling capacitor which is required in a single supply, singleended amplifier configuration. Without an output coupling capacitor, the half-supply bias across the load would result in both increased internal IC power dissipation and also possible loudspeaker damage. POWER DISSIPATION Power dissipation is a major concern when designing a successful amplifier, whether the amplifier is bridged or single-ended. A direct consequence of the increased power delivered to the load by a bridge amplifier is an increase in internal power dissipation. The maximum internal power dissipation per channel is 4 times that of a single-ended amplifier. The maximum power dissipation for a given application can be derived from the power dissipation graphs or from Equation (2). PDMAX = 4*(VDD)2/(2π2RL) (2) It is critical that the maximum junction temperature TJMAX of 150°C is not exceeded. TJMAX is a function of PDMAX and the PC board foil area. By adding copper foil, the thermal resistance of the application can be reduced from the free air value of θJA, resulting in higher PDMAX values without thermal shutdown protection circuitry being activated. Additional copper foil can be added to any of the leads connected to the LM4992. It is especially effective when connected to VDD, GND, and the output pins. Refer to the application information on the LM4992 reference design board for an example of good heat sinking. If TJMAX still exceeds 150°C, then additional changes must be made. These changes can include reduced supply voltage, higher load impedance, or reduced ambient temperature. Internal power dissipation is a function of output power. Refer to the TYPICAL PERFORMANCE CHARACTERISTICs curves for power dissipation information for different output powers and output loading. EXPOSED-DAP MOUNTING CONSIDERATIONS The LM4992's exposed-DAP (die attach paddle) packages (NHK) provide a low thermal resistance between the die and the PCB to which the part is mounted and soldered. This allows rapid heat transfer from the die to the surrounding PCB copper area heatsink, copper traces, ground plane, and finally, surrounding air. The result is a low voltage audio power amplifier that produces 1.07W dissipation per channel in an 8Ω load at ≤ 1% THD+N. This power is achieved through careful consideration of necessary thermal design. Failing to optimize thermal design may compromise the LM4992's performance and activate unwanted, though necessary, thermal shutdown protection. Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LM4992 LM4992SDBD Submit Documentation Feedback 11 LM4992, LM4992SDBD SNAS220B – NOVEMBER 2003 – REVISED MAY 2013 www.ti.com The LM4992SD must have its DAP soldered to a copper pad on the PCB. The DAP's PCB copper pad is then, ideally, connected to a large plane of continuous unbroken copper. This plane forms a thermal mass, heat sink, and radiation area. Place the heat sink area on either outside plane in the case of a two-sided or multi-layer PCB. (The heat sink area can also be placed on an inner layer of a multi-layer board. The thermal resistance, however, will be higher.) Connect the DAP copper pad to the inner layer or backside copper heat sink area with vias. The via diameter should be 0.012in - 0.013in with a 1.27mm pitch. Ensure efficient thermal conductivity by plugging and tenting the vias with plating and solder mask, respectively. POWER SUPPLY BYPASSING As with any amplifier, proper supply bypassing is critical for low noise performance and high power supply rejection. The capacitor location on both the bypass and power supply pins should be as close to the device as possible. Typical applications employ a 5V regulator with 10 µF tantalum or electrolytic capacitor and a ceramic bypass capacitor which aid in supply stability. This does not eliminate the need for bypassing the supply nodes of the LM4992. The selection of a bypass capacitor, CB, is dependent upon PSRR requirements, click and pop performance (as explained in the section, PROPER SELECTION OF EXTERNAL COMPONENTS), system cost, and size constraints. SHUTDOWN FUNCTION In order to reduce power consumption while not in use, the LM4992 contains shutdown circuitry that is used to independently turn off each channel's bias circuitry. This shutdown feature turns a given channel off when logic low is placed on the corresponding shutdown pin. By switching a particular shutdown pin to GND, the LM4992 supply current draw due to that channel will be minimized in idle mode. Idle current is measured with the shutdown pin connected to GND. The trigger point for shutdown is shown as a typical value in the Shutdown Hysteresis Voltage graphs in the TYPICAL PERFORMANCE CHARACTERISTICs section. It is best to switch between ground and supply for maximum performance. While the device may be disabled with shutdown voltages in between ground and supply, the idle current may be greater than the typical value of 0.2µA. In either case, the shutdown pin should be tied to a definite voltage to avoid unwanted state changes. In many applications, a microcontroller or microprocessor output is used to control the shutdown circuitry, which provides a quick, smooth transition to shutdown. Another solution is to use a single-throw switch in conjunction with an external pull-up resistor. This scheme ensures that the shutdown pin will not float, thus preventing unwanted state changes. PROPER SELECTION OF EXTERNAL COMPONENTS Proper selection of external components in applications using integrated power amplifiers is critical to optimize device and system performance. While the LM4992 is tolerant of external component combinations, consideration to component values must be used to maximize overall system quality. The LM4992 is unity-gain stable which gives the designer maximum system flexibility. The LM4992 should be used in low gain configurations to minimize THD+N values, and maximize the signal to noise ratio. Low gain configurations require large input signals to obtain a given output power. Input signals equal to or greater than 1 Vrms are available from sources such as audio codecs. Please refer to the section, AUDIO POWER AMPLIFIER DESIGN, for a more complete explanation of proper gain selection. Besides gain, one of the major considerations is the closed-loop bandwidth of the amplifier. To a large extent, the bandwidth is dictated by the choice of external components shown in Figure 1. The input coupling capacitor, Ci, forms a first order high pass filter which limits low frequency response. This value should be chosen based on needed frequency response for a few distinct reasons. Selection Of Input Capacitor Size Large input capacitors are both expensive and space hungry for portable designs. Clearly, a certain sized capacitor is needed to couple in low frequencies without severe attenuation. But in many cases the speakers used in portable systems, whether internal or external, have little ability to reproduce signals below 100Hz to 150Hz. Thus, using a large input capacitor may not increase actual system performance. 12 Submit Documentation Feedback Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LM4992 LM4992SDBD LM4992, LM4992SDBD www.ti.com SNAS220B – NOVEMBER 2003 – REVISED MAY 2013 In addition to system cost and size, click and pop performance is effected by the size of the input coupling capacitor, Ci. A larger input coupling capacitor requires more charge to reach its quiescent DC voltage (nominally 1/2 VDD). This charge comes from the output via the feedback and is apt to create pops upon device enable. Thus, by minimizing the capacitor size based on necessary low frequency response, turn-on pops can be minimized. Besides minimizing the input capacitor size, careful consideration should be paid to the bypass capacitor value. Bypass capacitor, CB, is the most critical component to minimize turn-on pops since it determines how fast the LM4992 turns on. The slower the LM4992's outputs ramp to their quiescent DC voltage (nominally 1/2 VDD), the smaller the turn-on pop. Choosing CB equal to 1.0µF along with a small value of Ci (in the range of 0.1µF to 0.39µF), should produce a virtually clickless and popless shutdown function. While the device will function properly, (no oscillations or motorboating), with CB equal to 0.1µF, the device will be much more susceptible to turn-on clicks and pops. Thus, a value of CB equal to 1.0µF is recommended in all but the most cost sensitive designs. AUDIO POWER AMPLIFIER DESIGN A 1W/8Ω Audio Amplifier Given: Power Output 1 Wrms Load Impedance 8Ω Input Level 1 Vrms Input Impedance Bandwidth 20 kΩ 100 Hz–20 kHz ± 0.25 dB A designer must first determine the minimum supply rail to obtain the specified output power. By extrapolating from the Output Power vs Supply Voltage graphs in the TYPICAL PERFORMANCE CHARACTERISTICs section, the supply rail can be easily found. 5V is a standard voltage in most applications, it is chosen for the supply rail. Extra supply voltage creates headroom that allows the LM4992 to reproduce peaks in excess of 1W without producing audible distortion. At this time, the designer must make sure that the power supply choice along with the output impedance does not violate the conditions explained in the POWER DISSIPATION section. Once the power dissipation equations have been addressed, the required differential gain can be determined from Equation (3). (3) (4) Rf/Ri = AVD/2 From Equation (3), the minimum AVD is 2.83; use AVD = 3. Since the desired input impedance was 20 kΩ, and with a AVD impedance of 2, a ratio of 1.5:1 of Rf to Ri results in an allocation of Ri = 20 kΩ and Rf = 30 kΩ. The final design step is to address the bandwidth requirements which must be stated as a pair of −3 dB frequency points. Five times away from a −3 dB point is 0.17 dB down from passband response which is better than the required ±0.25 dB specified. fL = 100 Hz/5 = 20 Hz fH = 20 kHz * 5 = 100 kHz (5) (6) As stated in the PROPER SELECTION OF EXTERNAL COMPONENTS section, Ri in conjunction with Ci create a highpass filter. Ci ≥ 1/(2π*20 kΩ*20 Hz) = 0.397 µF; use 0.39 µF (7) The high frequency pole is determined by the product of the desired frequency pole, fH, and the differential gain, AVD. With a AVD = 3 and fH = 100 kHz, the resulting GBWP = 300kHz which is much smaller than the LM4992 GBWP of 1.5MHz. This figure displays that if a designer has a need to design an amplifier with a higher differential gain, the LM4992 can still be used without running into bandwidth limitations. Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LM4992 LM4992SDBD Submit Documentation Feedback 13 LM4992, LM4992SDBD SNAS220B – NOVEMBER 2003 – REVISED MAY 2013 www.ti.com The LM4992 is unity-gain stable and requires no external components besides gain-setting resistors, an input coupling capacitor, and proper supply bypassing in the typical application. However, if a closed-loop differential gain of greater than 10 is required, a feedback capacitor (C4) may be needed as shown in SCHEMATIC DRAWING to bandwidth limit the amplifier. This feedback capacitor creates a low pass filter that eliminates possible high frequency oscillations. Care should be taken when calculating the -3dB frequency in that an incorrect combination of R3 and C4 will cause rolloff before 20kHz. A typical combination of feedback resistor and capacitor that will not produce audio band high frequency rolloff is R3 = 20kΩ and C4 = 25pf. These components result in a -3dB point of approximately 320 kHz. PCB LAYOUT GUIDELINES This section provides practical guidelines for mixed signal PCB layout that involves various digital/analog power and ground traces. Designers should note that these are only "rule-of-thumb" recommendations and the actual results will depend heavily on the final layout. GENERAL MIXED SIGNAL LAYOUT RECOMMENDATION Power and Ground Circuits For 2 layer mixed signal design, it is important to isolate the digital power and ground trace paths from the analog power and ground trace paths. Star trace routing techniques (bringing individual traces back to a central point rather than daisy chaining traces together in a serial manner) can have a major impact on low level signal performance. Star trace routing refers to using individual traces to feed power and ground to each circuit or even device. This technique will require a greater amount of design time but will not increase the final price of the board. The only extra parts required will be some jumpers. Single-Point Power / Ground Connections The analog power traces should be connected to the digital traces through a single point (link). A "Pi-filter" can be helpful in minimizing High Frequency noise coupling between the analog and digital sections. It is further recommended to put digital and analog power traces over the corresponding digital and analog ground traces to minimize noise coupling. Placement of Digital and Analog Components All digital components and high-speed digital signal traces should be located as far away as possible from analog components and circuit traces. Avoiding Typical Design / Layout Problems Avoid ground loops or running digital and analog traces parallel to each other (side-by-side) on the same PCB layer. When traces must cross over each other do it at 90 degrees. Running digital and analog traces at 90 degrees to each other from the top to the bottom side as much as possible will minimize capacitive noise coupling and cross talk. 14 Submit Documentation Feedback Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LM4992 LM4992SDBD LM4992, LM4992SDBD www.ti.com SNAS220B – NOVEMBER 2003 – REVISED MAY 2013 SCHEMATIC DRAWING VDD R3 C4 R2 C2 20 k: + 0.38 PF C1 1 PF -IN - +IN + Vo1 - 20 k: 20 k: J2 VDD + Vo1 + Vo2 BIAS C3 1.0 PF R1 20 k: + VDD/2 Bypass Shutdown J1 VDD R1 20 k: J1 BIAS Shutdown Bypass C3 1.0 PF VDD/2 + J2 20 k: 20 k: + C2 R2 20 k: +IN -IN + - Vo2 - 0.38 PF C4 R3 Figure 30. Higher Gain Schematic Drawing Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LM4992 LM4992SDBD Submit Documentation Feedback 15 LM4992, LM4992SDBD SNAS220B – NOVEMBER 2003 – REVISED MAY 2013 www.ti.com Demonstration Board Layout Figure 31. Recommended WSON Board Layout: Top Overlay Figure 32. Recommended WSON Board Layout: Top Layer 16 Submit Documentation Feedback Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LM4992 LM4992SDBD LM4992, LM4992SDBD www.ti.com SNAS220B – NOVEMBER 2003 – REVISED MAY 2013 Figure 33. Recommended WSON Board Layout: Bottom Layer Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LM4992 LM4992SDBD Submit Documentation Feedback 17 LM4992, LM4992SDBD SNAS220B – NOVEMBER 2003 – REVISED MAY 2013 www.ti.com REVISION HISTORY Changes from Revision A (May 2013) to Revision B • 18 Page Changed layout of National Data Sheet to TI format .......................................................................................................... 17 Submit Documentation Feedback Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LM4992 LM4992SDBD PACKAGE OPTION ADDENDUM www.ti.com 9-Aug-2013 PACKAGING INFORMATION Orderable Device Status (1) LM4992SD/NOPB ACTIVE Package Type Package Pins Package Drawing Qty WSON NHK 14 1000 Eco Plan Lead/Ball Finish (2) Green (RoHS & no Sb/Br) MSL Peak Temp Op Temp (°C) Device Marking (3) CU SN Level-1-260C-UNLIM (4/5) -40 to 85 L4992 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 Samples PACKAGE MATERIALS INFORMATION www.ti.com 11-Oct-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device LM4992SD/NOPB Package Package Pins Type Drawing WSON NHK 14 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 1000 178.0 12.4 Pack Materials-Page 1 3.3 B0 (mm) K0 (mm) P1 (mm) 4.3 1.0 8.0 W Pin1 (mm) Quadrant 12.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 11-Oct-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM4992SD/NOPB WSON NHK 14 1000 210.0 185.0 35.0 Pack Materials-Page 2 MECHANICAL DATA NHK0014A SDA14A (Rev A) www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2013, Texas Instruments Incorporated