Document 1111-1 Shielded Power Inductors–MSS1583 • 14.8 × 14.8 mm footprint; 8.6 mm high shielded inductors • 16 inductance values from 10 µH to 1 mH • Low DCR and excellent current handling Core material Ferrite Core and winding loss See www.coilcraft.com/coreloss Environment RoHS compliant, halogen free Terminations RoHS compliant matte tin over nickel over phos bronze. Other terminations available at additional cost. Weight: 3.7 – 4.4 g Ambient temperature –40°C to +85°C with (40°C rise) Irms current. Maximum part temperature +125°C (ambient + temp rise). Derating. Storage temperature Component: –40°C to +125°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 300/13″ reel; Plastic tape: 32 mm wide, 0.5 mm thick, 24 mm pocket spacing, 8.6 mm pocket depth PCB washing Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. See Doc787_PCB_Washing.pdf. Part number1 MSS1583-103ME_ MSS1583-123ME_ MSS1583-153ME_ MSS1583-183ME_ MSS1583-223ME_ MSS1583-333ME_ MSS1583-473ME_ MSS1583-683ME_ MSS1583-104KE_ MSS1583-154KE_ MSS1583-224KE_ MSS1583-334KE_ MSS1583-474KE_ MSS1583-684KE_ MSS1583-824KE_ MSS1583-105KE_ Inductance2 (µH) 10 ±20% 12 ±20% 15 ±20% 18 ±20% 22 ±20% 33 ±20% 47 ±20% 68 ±20% 100 ±10% 150 ±10% 220 ±10% 330 ±10% 470 ±10% 680 ±10% 820 ±10% 1000 ±10% DCR (Ohms)3 typ max 0.012 0.014 0.014 0.017 0.018 0.021 0.020 0.023 0.023 0.026 0.033 0.038 0.048 0.055 0.061 0.070 0.090 0.103 0.138 0.159 0.205 0.235 0.300 0.345 0.386 0.445 0.570 0.655 0.640 0.736 0.860 0.990 Isat (A)5 Irms (A)6 SRF typ4 (MHz) 10% drop 20% drop 30% drop 20°C rise 40°C rise 17.0 12.0 13.6 14.7 5.0 7.4 14.5 11.7 13.3 14.2 4.4 6.3 13.5 10.1 11.5 12.4 4.3 6.1 12.0 9.2 10.5 11.2 3.9 5.5 10.5 8.2 9.1 10.4 3.7 5.3 8.5 7.0 7.9 8.6 3.4 4.8 7.3 5.9 6.7 7.3 2.7 3.7 6.0 4.7 5.5 6.0 2.5 3.4 4.8 3.9 4.4 4.8 2.0 2.8 3.7 3.1 3.6 3.9 1.55 2.20 3.0 2.6 3.0 3.3 1.30 1.80 2.7 2.0 2.3 2.5 1.00 1.45 2.2 1.8 2.0 2.2 0.96 1.35 1.8 1.4 1.6 1.8 0.78 1.10 1.6 1.3 1.5 1.6 0.74 1.0 1.5 1.1 1.3 1.4 0.63 0.86 1. Specify termination and packaging codes: MSS1583-105KED Termination: E = RoHS compliant matte tin over nickel over phos bronze. Special order: Q = RoHS tin-silver-copper (95.5/4/0.5) or P = non-RoHS tin-lead (63/37). Packaging: D = 13″ machine-ready reel. EIA-481 embossed plastic tape (300 parts per full reel). B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter D instead. 2. Inductance tested at 100 kHz, 0.1 Vrms, 0 Adc using an Agilent/ HP 4263B LCR meter or equivalent. 3. DCR measured on a micro-ohmmeter and a Coilcraft CCF858 test fixture. 4. SRF measured using Agilent/HP 4191A or equivalent. 5. DC current at 25°C that causes the specified drop in inductance from its value without current. Click for temperature derating information. 6. Current that causes the specified temperature rise from 25°C ambient. This information is for reference only and does not represent absolute maximum ratings. Click for temperature derating information. 7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Document 1111-1 Revised 07/10/15 Document 1111-2 Shielded Power Inductors – MSS1583 Typical L vs Current Typical L vs Frequency 10,000 10,000 220 µH 100 100 µH 22 µH 10 1 10 1 220 µH 100 µH 100 22 µH 10 µH 10 10 µH 0.1 1000 µH 1000 1000 µH Inductance (µH) Inductance (µH) 1000 100 Current (A) 1 0.1 1 10 100 Frequency (MHz) 0.590 ±0.020 15,0 ±0,5 0.590 ±0.020 15,0 ±0,5 123 Dash number X Internal code 0.030 typ 0,76 0.339 max 8,6 0.130 3,3 0.236 6,0 0.220 5,6 0.323 8,2 inches Dimensions are in mm 0.150 3,8 0.453 11,5 Recommended Land Pattern Document 1111-2 Revised 07/10/15