DATA SHEET
1G bits GDDR5 SGRAM
EDW1032BBBG (32M words x 32 bits)
Specifications
Features
• Density: 1G bits
• Organization
— 2Mbit x 32 I/O x 16 banks
— 4Mbit x 16 I/O x 16 banks
• Package
— 170-ball FBGA
— Lead-free (RoHS compliant) and Halogen-free
• Power supply:
— VDD: 1.5V ±3% and 1.35V ± 3%
— VDDQ: 1.5V ±3% and 1.35V ±3%
• Data rate: 7.0Gbps/6.0Gbps/5.0Gbps/4.0Gbps (max.)
• 16 internal banks
• Four bank groups for tCCDL = 3tCK
• 8n prefetch architecture: 256 bit per array Read or
Write access; 128 bit for x16
• Burst length (BL): 8 only
• Programmable CAS latency: 6 to 20
• Programmable Write latency: 3 to 7
• Programmable CRC READ latency: 0 to 3
• Programmable CRC WRITE latency: 8 to 14
• Programmable EDC hold pattern for CDR
• Precharge: auto precharge option for each burst
access
• Refresh: auto-refresh, self-refresh
• Refresh cycles: 8192 cycles/32ms
• Interface: Pseudo open drain (POD-15)
• On-die termination (ODT): nom. values of 60Ω or 120Ω
• Pseudo open drain (POD-15) compatible outputs
— 40Ω pulldown
— 60Ω pullup
• ODT and output driver strength auto-calibration with
external resistor ZQ pin (120Ω)
• Programmable termination and driver strength offsets
• Selectable external or internal VREF for data inputs;
programmable offsets for internal VREF
• Separate external VREF for address / command inputs
• Operating case temperature range
— TC = 0°C to +95°C
• x32/x16 mode configuration set at power-up with
EDC pin
• Single ended interface for data, address and command
• Quarter data-rate differential clock inputs CK, /CK for
address and commands
• Two half data-rate differential clock inputs WCK, /WCK,
each associated with two data bytes (DQ, /DBI, EDC)
• Double Data Rate (DDR) data (WCK)
• Single Data Rate (SDR) command (CK)
• Double Data Rate (DDR) addressing (CK)
• Write data mask function via address bus
(single/double byte mask)
• Data Bus Inversion (DBI) and Address Bus Inversion
(ABI)
• Input/output PLL on/off mode
• Address training: address input monitoring via DQ pins
• WCK2CK clock training: phase information via EDC
pins
• Data read and write training via Read FIFO (FIFO
depth = 6)
• Read FIFO pattern preload by LDFF command
• Direct write data load to Read FIFO by WRTR
command
• Consecutive read of Read FIFO by RDTR command
• Read/Write data transmission integrity secured by
cyclic redundancy check (CRC–8)
• Read/Write EDC on/off mode
• DQ Preamble for Read on/off mode
• Low Power modes
• RDQS mode on EDC pin
• On-chip temperature sensor with read-out
• Automatic temperature sensor controlled self-refresh
rate
• Digital tRAS lockout
• Vendor ID, FIFO depth and Density info fields for
identification
• Mirror function with MF pin
• Boundary Scan function with SEN pin
Document No. E1771E11 (Ver. 1.1)
Date Published September 2011 (K) Japan
Printed in Japan
URL: http://www.elpida.com
Elpida Memory, Inc. 2011
EDW1032BBBG
Ordering Information
Organization
(words x bits)
Part number
EDW1032BBBG-40-F
EDW1032BBBG-50-F
EDW1032BBBG-60-F
EDW1032BBBG-70-F
32M x 32
Max. Data Rate (Gbps/pin)
Package
4.0
5.0
6.0
7.0
170-ball FBGA
Part Number
E D W 10 32 B B BG - 60 - F
Elpida Memory
Environment Code
F: Lead Free (RoHS compliant)
and Halogen Free
Type
D: Packaged Device
Product Family
W: GDDR5 SGRAM
Speed
40: 4.0Gbps
50: 5.0Gbps
60: 6.0Gbps
70: 7.0Gbps
Density/Bank
10: 1Gb/16-bank
Package
BG: FBGA
Organization
32: x32
Revision
Power Supply, Interface
B: VDD = 1.5V
Data Sheet E1771E11 (Ver. 1.1)
2
EDW1032BBBG
Pin Configuration
789:: %(; <=>?9@A
#
$
4%5
#
& "
%
! 4!
4%5
#
#
4&
(
4
)
%
%
4&. 4!
4%5
$
*
$
4!
!
'
& "
"
!
%
%
#
4
+
4
"
$
4%5
! 4!
,
4%5
&
.
"
#
$
/
;.CA
Data Sheet E1771E11 (Ver. 1.1)
3
& EDW1032BBBG
EDOO)%*$ 0) &RQILJXUDWLRQ
9664
'4
9664
'4
1&
$
9''4
'4
9''4
'4
966
%
966
9664
('&
9664
9664
9''
&
9''4
'%,
9''4 :&. :&.
9664
'4
9664
'4
9''4
'4
9''4
9''
9''4
966
9664
0)
9664
'4
9664
'4
9''4
'4
9''4
9''
9664
9664
('&
9664
'
966
9''
9''4
'%,
9''4
9''4
(
9''4
'4
9664
'4
9664
'4
9664
)
9664
'4
9''4
'4
9''4
&$6
9''
966
*
966
9''
:(
9''4
9''
9''4
$
$
$
$
+
%$
$
%$
$
9''4
9664
966
$%,
1&
-
6(1
&.
&.
=4
95()&
5(6(7 &.(
95()' '4
966
9664
9''4
$
$
$
$
.
%$
$
%$
$
9''4
9664
966
9''
9''4
5$6
9''
966
/
966
9''
&6
9''4
9''
9''4
'4
9''4
'4
9664
0
9664
'4
9''4
'4
9''4
9664
'4
9664
'4
9''4
1
9''4
'4
9664
'4
9664
9''4
'%,
9''4 :&. :&.
3
966
9''
9''4
'%,
9''4
9664
('&
9664
9664
9''
5
9''
9664
9664
('&
9664
9''4
'4
9''4
'4
966
7
966
'4
9''4
'4
9''4
9664
'4
9664
'4
1&
8
95()'
'4
9664
'4
9664
SLQLV2))LQ[PRGH
7RS9LHZ
Signal
Function
Signal
Function
CK, /CK
Clock
ZQ
Impedance Reference
WCK01, /WCK01,
WCK23, /WCK23
Data Clocks
/RESET
Reset
/CKE
Clock Enable
MF
Mirror Function
/CS
Chip Select
SEN
Scan Enable
/RAS, /CAS, /WE
Command inputs
VREFC
Reference voltage for command and address
BA0 - BA3
Bank Address inputs
VREFD
Reference voltage for DQ and /DBI
A0 - A11
Address inputs
VDDQ
I/O power
DQ0 - DQ31
Data Input/Output
VSSQ
I/O ground
/DBI0 - /DBI3
Data bus inversion
VDD
Power supply
EDC0 - EDC3
Error Detection Code
VSS
Ground
/ABI
Address bus inversion
NC
Not connected
Note: 1.
/xxx indicates active low signal.
Data Sheet E1771E11 (Ver. 1.1)
4
EDW1032BBBG
1.
Configuration
The Elpida GDDR5 SGRAM is a high speed dynamic random-access memory designed for applications requiring
high bandwidth. It contains 1,073,741,824 bits and is internally configured as a 16-bank DRAM.
The GDDR5 SGRAM uses a 8n prefetch architecture and DDR interface to achieve high-speed operation. The
device can be configured to operate in x32 mode or x16 (clamshell) mode. The mode is detected during device
initialization. The GDDR5 interface transfers two 32 bit wide data words per WCK clock cycle to/from the I/O pins.
Corresponding to the 8n prefetch a single write or read access consists of a 256 bit wide, two CK clock cycle data
transfer at the internal memory core and eight corresponding 32 bit wide one-half WCK clock cycle data transfers
at the I/O pins.
The GDDR5 SGRAM operates from a differential clock CK and /CK. Commands are registered at every rising edge
of CK. Addresses are registered at every rising edge of CK and every rising edge of /CK.
GDDR5 replaces the pulsed strobes (WDQS & RDQS) used in previous DRAMs such as GDDR4 with a free running
differential forwarded clock (WCK, /WCK) with both input and output data registered and driven respectively at both
edges of the forwarded WCK.
Read and write accesses to the GDDR5 SGRAM are burst oriented; an access starts at a selected location and
continues for a total of eight data words. Accesses begin with the registration of an ACTIVE command, which is then
followed by a READ or WRITE command. The address bits registered coincident with the ACTIVE command and
the next rising /CK edge are used to select the bank and the row to be accessed. The address bits registered
coincident with the READ or WRITE command and the next rising /CK edge are used to select the bank and the
column location for the burst access.
Data Sheet E1771E11 (Ver. 1.1)
5
EDW1032BBBG
1.1
Signal Description
Table 1: Signal Description
Signal
CK, /CK
Type
Detailed Function
Input
Clock: CK and /CK are differential clock inputs. Command inputs are latched on the rising
edge of CK. Address inputs are latched on the rising edge of CK and the rising edge of /CK.
All latencies are referenced to CK. CK and /CK are externally terminated.
WCK01, /WCK01,
Input
WCK23, /WCK23
Data Clocks: WCK and /WCK are differential clocks used for WRITE data capture and READ
data output. WCK01, /WCK01 is associated with DQ0-DQ15, /DBI0, /DBI1, EDC0 and EDC1.
WCK23, /WCK23 is associated with DQ16-DQ31, /DBI2, /DBI3, EDC2 and EDC3. WCK clocks
operate at nominally twice the CK clock frequency.
/CKE
Input
Clock Enable: /CKE low activates and /CKE high deactivates internal clock, device input
buffers and output drivers. Taking /CKE high provides Precharge Power-Down and SelfRefresh operations (all banks idle), or Active Power-Down (row active in any bank). /CKE is
synchronous for Power-Down entry and exit and for Self-Refresh entry. /CKE must be
maintained low throughout READ and WRITE accesses.
Input buffers excluding CK, /CK, /CKE, WCK01, /WCK01, WCK23, /WCK23 are disabled
during Power-Down. Input buffers excluding /CKE are disabled during Self-Refresh.
The value of /CKE latched at power-up with /RESET going high determines the termination
value of the address and command inputs.
/CS
Input
Chip Select: /CS low enables, and /CS high disables the command decoder. All commands
are masked when /CS is registered high, but internal command execution continues. /CS
provides for individual device selection on memory channels with multiple memory devices.
/CS is considered part of the command code.
/RAS, /CAS, /WE
Input
Command inputs: /RAS, /CAS and /WE (along with /CS) define the command to be entered.
Input
Bank Address inputs: BA0-BA3 define to which bank an ACTIVE, READ, WRITE or
PRECHARGE command is being applied. BA0-BA3 also determine which Mode Register is
accessed with a MODE REGISTER SET command. BA0-BA3 are sampled with the rising edge
of CK.
A0 - A11
Input
Address inputs: A0-A11 provide the row address for ACTIVE commands. A0-A5(A6) provide
the column address and A8 defines the auto precharge function for READ and WRITE
commands, to select one location out of the memory array in the respective bank. A8 sampled
during a PRECHARGE command determines whether the PRECHARGE applies to one bank
(A8 low, bank selected by BA0-BA3) or all banks (A8 high). The address inputs also provide
the op-code during an MODE REGISTER SET command, and the data bits during LDFF
commands. A8-A11 are sampled with the rising edge of CK and A0-A7 are sampled with the
rising edge of /CK.
DQ0 - DQ31
I/O
Data Input/Output: 32 bit data bus
/DBI0 - /DBI3
I/O
Data bus inversion: /DBI0 is associated with DQ0-DQ7, /DBI1 with DQ8-DQ15, /DBI2 with
DQ16-DQ23, and /DBI3 with DQ24-DQ31.
EDC0 - EDC3
Output
Error Detection Code: The calculated CRC data is transmitted on these pins. In addition
these pins drive a hold pattern when idle and can be used as an RDQS function. EDC0 is
associated with DQ0-DQ7, EDC1 with DQ8-DQ15, EDC2 with DQ16-DQ23, and EDC3 with
DQ24-DQ31.
/ABI
Input
Address bus inversion
ZQ
-
Impedance Reference: external reference pin for auto-calibration
/RESET
Input
Reset: VDDQ CMOS input. /RESET low asynchronously initiates a full chip reset. With
/RESET low all ODTs are disabled.
MF
Input
Mirror Function: VDDQ CMOS input. Must be tied to Power or Ground.
SEN
Input
Scan Enable: VDDQ CMOS input. Must be tied to Ground when not in use.
VREFC
Supply
Reference voltage for command and address inputs.
VREFD
Supply
Reference voltage for DQ and /DBI inputs.
BA0 - BA3
VDDQ
Supply
Isolated power for the input and output buffers.
VSSQ
Supply
Isolated ground for the input and output buffers.
VDD
Supply
Power supply
VSS
Supply
Ground
NC
-
Not connected
Data Sheet E1771E11 (Ver. 1.1)
6
EDW1032BBBG
1.2
Mirror Function Mode
The GDDR5 SGRAM provides a mirror function (MF) pin to change the physical location of the command, address,
data and WCK pins assisting in routing devices back to back. The MF ball should be tied directly to VSSQ or VDDQ
depending on the control line orientation desired.
The pins affected by this Mirror Function mode are listed in Table 2.
Table 2: Ball Assignment with Mirror Function
Signal
Ball
MF=0
M=1
Signal
Ball
MF=0
Signal
M=1
Ball
Signal
MF=0
M=1
Ball
MF=0
MF=1
A9 A1
A2
DQ1
DQ25
A4
DQ0
DQ24
K5
A11 A6
G12
/CS
/WE
B2
DQ3
DQ27
B4
DQ2
DQ26
P5
/WCK23 /WCK01
L12
/WE
/CS
C2
EDC0
EDC3
D4
WCK01 WCK23
H10
BA3 A3
BA1 A5
A13
DQ9
DQ17
D2
/DBI0
/DBI3
E4
DQ4
DQ28
K10
BA1 A5
BA3 A3
B13
DQ11
DQ19
E2
DQ5
DQ29
F4
DQ6
DQ30
A11
DQ8
DQ16
C13
EDC1
EDC2
F2
DQ7
DQ31
H4
A10 A0
A8 A7
B11
DQ10
DQ18
D13
/DBI1
/DBI2
M2
DQ31
DQ7
K4
A8 A7
A10 A0
E11
DQ12
DQ20
E13
DQ13
DQ21
N2
DQ29
DQ5
M4
DQ30
DQ6
F11
DQ14
DQ22
F13
DQ15
DQ23
P2
/DBI3
/DBI0
N4
DQ28
DQ4
H11
BA0 A2
BA2 A4
M13
DQ23
DQ15
R2
EDC3
EDC0
P4
WCK23 WCK01
K11
BA2 A4
BA0 A2
N13
DQ21
DQ13
T2
DQ27
DQ3
T4
DQ26
DQ2
M11
DQ22
DQ14
P13
/DBI2
/DBI1
U2
DQ25
DQ1
U4
DQ24
DQ0
N11
DQ20
DQ12
R13
EDC2
EDC1
G3
/RAS
/CAS
D5
/WCK01 /WCK23
T11
DQ18
DQ10
T13
DQ19
DQ11
L3
/CAS
/RAS
H5
A9 A1
U11
DQ16
DQ8
U13
DQ17
DQ9
A11 A6
Functions within the GDDR5 SGRAM that refer to external signals are transparent with respect to Mirror Function
mode, meaning that the signal names shown in the respective functional description apply both to mirrored (MF=1)
and non-mirrored (MF=0) modes. The referenced package pin is determined by the Mirror Function mode the
devices is configured to.
1.3
Clamshell Mode Detection
The GDDR5 SGRAM can operate in a x32 mode or a x16 mode to allow a clamshell configuration with a point to
point connection on the high speed data signals. The disabled pins in x16 mode will be in Hi-Z state, non-terminating.
The x16 mode is detected at power-up on the pin at location C-13 which is EDC1 when configured to MF=0 and
EDC2 when configured to MF=1. For x16 mode this pin is tied to VSSQ; the pin is part of the two bytes that are
disabled in this mode and therefore not needed for EDC functionality. For x32 mode this pin is active and always
terminated to VDDQ in the system or by the controller. The configuration is set with /RESET going high. Once the
configuration has been set, it cannot be changed during normal operation. Usually the configuration is fixed in the
system.
Table 3: Clamshell Mode and Mirror Function
Mode
MF
EDC1 (MF=0) or EDC2 (MF=1)
x16 non-mirrored
VSSQ
VSSQ
x32 non-mirrored
VSSQ
VDDQ (terminated by the system or controller)
x16 mirrored
VDDQ
VSSQ
x32 mirrored
VDDQ
VDDQ (terminated by the system or controller)
Data Sheet E1771E11 (Ver. 1.1)
7
EDW1032BBBG
1.4
Clocking
The GDDR5 SGRAM operates from a differential clock CK and /CK. Commands are registered at every rising edge
of CK. Addresses are registered at every rising edge of CK and every rising edge of /CK.
GDDR5 uses a double data rate data interface and an 8n-prefetch architecture. The data interface uses two
differential forwarded clocks (WCK, /WCK). DDR means that the data is registered at every rising edge of WCK and
rising edge of /WCK. WCK and /WCK are continuously running and operate at twice the frequency of the
command/address clock (CK, /CK).
&.
&.
&RPPDQG
$GGUHVV
:&.
:&.
'DWD
1RWHWKHILJXUHVKRZVWKHUHODWLRQVKLSEHWZHHQWKHGDWDUDWHRIWKHEXVHVDQGWKHFORFNVDQGLVQRWDWLPLQJGLDJUDP
Figure 1: GDDR5 Clocking and Interface Relationship
1.5
Addressing
The GDDR5 SGRAM uses a double data rate address scheme to reduce pins required on the GDDR5 SGRAM as
shown in Table 4. The addresses should be provided to the GDDR5 SGRAM in two parts; the first half is latched on
the rising edge of CK along with the command pins such as /RAS, /CAS and /WE; the second half is latched on the
rising edge of /CK.
The use of DDR addressing allows all address values to be latched in at the same rate as the SDR commands. All
addresses related to command access have been positioned for latching on the initial rising edge for faster
decoding.
Table 4: Address Pairs
Clock Edge
Address Inputs
Rising CK
BA3
BA2
BA1
BA0
A11
A10
A9
A8
Rising /CK
A3
A4
A5
A2
A6
A0
A1
A7
Addressing schemes for x32 mode and x16 mode differ only in the number of valid column addresses, as shown in
Table 5.
Table 5: Addressing Scheme
32M x 32
64M x 16
Row Address
A0-A11
A0-A11
Column address
A0-A5
A0-A6
Bank address
BA0-BA3
BA0-BA3
Autoprecharge
A8
A8
Page size
2 KB
2 KB
Refresh
8k/32ms
8k/32ms
Refresh period
3.9 µs
3.9 µs
Data Sheet E1771E11 (Ver. 1.1)
8
EDW1032BBBG
1.6
Commands
Table 6: Command Truth Table
Operation
Code
/CKE /CKE
n-1
n
/CS
/RAS /CAS /WE
BA3BA0
A11
A10
A8
A6-A7, A0-A5
A9
(A6) Note
DESELECT
DESEL
L
X
H
X
X
X
X
X
X
X
X
X
2,8
NO OPERATION
(NOP)
NOP
L
X
L
H
H
H
X
X
X
X
X
X
2,8
MODE REGISTER
SET
MRS
L
L
L
L
L
L
MRA
OPCODE
ACTIVATE
ACT
L
L
L
L
H
H
BA
RA
READ
RD
L
L
L
H
L
H
BA
L
L
L
X
CA
2,5,9
READ with
Autoprecharge
RDA
L
L
L
H
L
H
BA
L
L
H
X
CA
2,5
LOAD FIFO
LDFF
L
L
L
H
L
H
BST
H
L
L
DATA
READ TRAINING
RDTR
L
L
L
H
L
H
X
H
H
L
X
X
2
WRITE without Mask
WR
L
L
L
H
L
L
BA
L
L
L
X
CA
2,5
WRITE without Mask
with Autoprecharge
WRA
L
L
L
H
L
L
BA
L
L
H
X
CA
2,5
WRITE with Single
Byte Mask
WSM
L
L
L
H
L
L
BA
L
H
L
X
CA
2,5
WRITE with
Autoprecharge, Single WSMA
Byte Mask
L
L
L
H
L
L
BA
L
H
H
X
CA
2,5
WRITE with Double
Byte Mask
WDM
L
L
L
H
L
L
BA
H
L
L
X
CA
2,5
WRITE with
Autoprecharge,
Double Byte Mask
WDMA
L
L
L
H
L
L
BA
H
L
H
X
CA
2,5
WRITE TRAINING
WRTR
L
L
L
H
L
L
X
H
H
L
X
X
2
PRECHARGE
PRE
L
L
L
L
H
L
BA
X
X
L
X
X
2
PRECHARGE ALL
PREALL L
L
L
L
H
L
X
X
X
H
X
X
2
REFRESH
REF
L
L
L
L
L
H
X
X
X
X
X
X
6
POWER-DOWNENTRY
PDE
L
H
X
X
X
X
X
X
POWER-DOWNEXIT
PDX
H
L
X
X
X
X
X
X
SELF-REFRESHENTRY
SRE
L
H
X
X
X
X
X
X
SELF-REFRESHEXIT
SRX
H
L
X
X
X
X
X
X
Notes: 1.
2.
3.
4.
5.
6.
7.
8.
9.
H
X
X
X
L
H
H
H
H
X
X
X
L
H
H
H
L
L
L
H
H
X
X
X
L
H
H
H
2,3
2,4
2,7
6
H = logic high level; L = logic low level; X = Don’t Care. Signal may be H or L, but not floating.
Addresses shown are logical addresses; physical addresses are inverted when address bus inversion (ABI) is
activated and /ABI=L.
BA0-BA3 provide the Mode Register address (MRA), A0-A11 the opcode to be loaded.
BA0-BA3 provide the bank address (BA), A0-A11 provide the row address (RA).
BA0-BA3 provide the bank address, A0-A5 (A6) provide the column address (CA); no sub-word addressing within a
burst of 8.
This command is REFRESH when /CKE(n) = L, and SELF-REFRESH ENTRY when /CKE(n) is H.
BA0-BA3 and CA are used to select burst location (BST) and data, respectively.
DESELECT and NO OPERATION are functionally interchangeable.
In address training mode READ is decoded from the command pins only with /RAS = H, /CAS = L, /WE= H.
Data Sheet E1771E11 (Ver. 1.1)
9
EDW1032BBBG
2.
Electrical Characteristics
Table 7: Absolute Maximum Ratings
Parameter
Symbol
Min.
Max.
Unit
Voltage on VDD supply relative to VSS
VDD
-0.5
2.0
V
Voltage on VDDQ supply relative to VSSQ
VDDQ
-0.5
2.0
V
Voltage on VREF and inputs relative to VSS
VIN
-0.5
2.0
V
Voltage on I/O pins relative to VSS
VOUT
-0.5
2.0
V
Storage Temperature
TSTG
-55
+150
°C
Junction Temperature
TJ
—
+125
°C
Short Circuit output current
IOUT
—
50
mA
Caution: Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent
damage of the device. This is a stress rating only, and functional operation of the device at these
or any other conditions above those indicated in the operational sections of these specification
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Data Sheet E1771E11 (Ver. 1.1)
10
EDW1032BBBG
2.1
Operating Conditions
Table 8: DC Operating Conditions
POD15
POD135
Parameter
Symbol
min.
typ.
max.
min.
typ.
max.
Device supply voltage
VDD
1.455
1.5
1.545
1.3095
1.35
1.3905
Unit Note
V
2
I/O Supply voltage
VDDQ
1.455
1.5
1.545
1.3095
1.35
1.3905
V
2
Reference voltage for DQ and /DBI pins
VREFD
0.69 *
VDDQ
—
0.71 *
VDDQ
0.69 *
VDDQ
—
0.71 *
VDDQ
V
3,4
Reference voltage for DQ and /DBI pins
VREFD2
0.49 *
VDDQ
—
0.51 *
VDDQ
0.49 *
VDDQ
—
0.51 *
VDDQ
V
3,4,5
External reference voltage for address and
VREFC
command
0.69 *
VDDQ
—
0.71 *
VDDQ
0.69 *
VDDQ
—
0.71 *
VDDQ
V
6
DC input logic high voltage for address and
VIHA(DC)
command inputs
VREFC
+ 0.15
—
—
VREFC
+ 0.135
—
—
V
DC input logic low voltage for address and
command inputs
VILA(DC)
—
—
VREFC
- 0.15
—
—
VREFC
- 0.135
V
DC input logic high voltage for DQ, /DBI
inputs with VREFD
VIHD(DC)
VREFD
+ 0.10
—
—
VREFD
+ 0.09
—
—
V
DC input logic low voltage for DQ, /DBI
inputs with VREFD
VILD(DC)
—
—
VREFD
- 0.10
—
—
VREFD
- 0.09
V
DC input logic high voltage for DQ, /DBI
inputs with VREFD2
VIHD2(DC)
VREFD2
+ 0.30
—
—
VREFD2
+ 0.27
—
—
V
DC input logic low voltage for DQ, /DBI
inputs with VREFD2
VILD2(DC)
—
—
VREFD2
- 0.30
—
—
VREFD2
- 0.27
V
Input logic high voltage for /RESET, SEN,
MF
VIHR
VDDQ
- 0.5
—
—
VDDQ
- 0.5
—
—
V
—
—
0.3
—
—
0.3
V
—
—
V
9
Input logic low voltage for /RESET, SEN, MF VILR
VIHX
VDDQ
- 0.3
—
—
VDDQ
- 0.3
VILX
—
—
0.3
—
—
0.3
V
9
Input leakage current
(any input 0V ≤ VIN ≤ VDDQ; all other pins IL
not under test = 0V)
-5
—
+5
-5
—
+5
μA
10
Output leakage current
(DQs are disabled; 0V ≤ VOUT ≤ VDDQ)
IOZ
-5
—
+5
-5
—
+5
μA
11
Output logic low voltage
VOL(DC)
—
—
0.62
—
—
0.56
V
External resistor value
ZQ
115
120
125
115
120
125
Ω
Input logic high voltage for EDC1/2
(x16 mode detect)
Input logic low voltage for EDC1/2
(x16 mode detect)
0°C ≤ TC ≤ 95°C. All voltages are measured at the package pins.
GDDR5 SGRAMs are designed to tolerate PCB designs with separate VDDQ and VDD power regulators.
AC noise in the system is estimated at 50 mV peak-to-peak for the purpose of DRAM design.
Source of reference voltage and control of Reference voltage for DQ and /DBI pins is determined by VREFD, Half
VREFD and VREFD Offset Mode Registers.
5. VREFD Offsets are not supported with VREFD2.
6. External VREFC is to be provided by the controller as there is no alternative supply.
7. DB, /DBI input slew rate must be greater than or equal to 3V/ns for POD15 and 2.7V/ns for POD135. The slew rate is
measured between VREFD crossing and VIHD(AC) or VILD(AC) or VREFD2 crossing and VIHD2(AC) or VILD2(AC).
8. ADR/CMD input slew rate must be greater than or equal to 3V/ns for POD15 and 2.7V/ns for POD135. The slew rate
is measured between VREFC crossing and VIHA(AC) or VILA(AC).
9. VIHX and VILX define the input voltage levels for the receiver that detects x32 mode or x16 mode with /RESET going
high.
10. IL is measured with ODT off. Any input 0V ≤ VIN ≤ VDDQ; all other pins not under test = 0V.
11. IOZ is measured with DQs disabled; 0V ≤ VOUT ≤ VDDQ.
Notes: 1.
2.
3.
4.
Data Sheet E1771E11 (Ver. 1.1)
11
EDW1032BBBG
Table 9: AC Operating Conditions
POD15
Parameter
Symbol
AC input logic high voltage for address and
VIHA(AC)
command inputs
POD135
min.
typ.
max.
min.
typ.
max.
Unit Note
VREFC
+ 0.20
—
—
VREFC
+ 0.18
—
—
V
AC input logic low voltage for address and
command inputs
VILA(AC)
—
—
VREFC
- 0.20
—
—
VREFC
- 0.18
V
AC input logic high voltage for DQ, /DBI
inputs with VREFD
VIHD(AC)
VREFD
+ 0.15
—
—
VREFD
+ 0.135
—
—
V
AC input logic low voltage for DQ, /DBI
inputs with VREFD
VILD(AC)
—
—
VREFD
- 0.15
—
—
VREFD
- 0.135
V
AC input logic high voltage for DQ, /DBI
inputs with VREFD2
VIHD2(AC)
VREFD2
+ 0.40
—
—
VREFD2
+ 0.36
—
—
V
AC input logic low voltage for DQ, /DBI
inputs with VREFD2
VILD2(AC)
—
—
VREFD2
- 0.40
—
—
VREFD2
- 0.36
V
Notes: 1.
2.
0°C ≤ TC ≤ 95°C. All voltages are measured at the package pins.
For optimum performance it is recommended that signal swings are larger than shown in the table.
Table 10: Clock Input Operating Conditions
POD15
Parameter
Symbol
Clock input mid-point voltage: CK, /CK
VMP(DC)
Clock input differential voltage: CK, /CK
VIDCK(DC)
POD135
min.
max.
min.
max.
Unit Note
VREFC
- 0.1
VREFC
+ 0.1
VREFC
- 0.1
VREFC
+ 0.1
V
2,7
0.22
—
0.198
—
V
5,7
Clock input differential voltage: CK, /CK
VIDCK(AC)
0.40
—
0.36
—
V
3,5,7
Clock input differential voltage: WCK, /WCK
VIDWCK(DC)
0.20
—
0.18
—
V
6,8
Clock input differential voltage: WCK, /WCK
VIDWCK(AC)
0.30
—
0.27
—
V
3,6,8
-0.3
VDDQ
+ 0.3
-0.3
VDDQ
+ 0.3
V
Clock input voltage level for CK, /CK,
WCK, /WCK single ended inputs
VIN
CK, /CK single ended slew rate
CKslew
3
—
2.7
—
V/ns 10
WCK, /WCK single ended slew rate
WCKSlew
3
—
2.7
—
V/ns 11
Clock input crossing point voltage: CK, /CK
VIXCK(AC)
VREFC
- 0.12
VREFC
+ 0.12
VREFC
- 0.108
VREFC
+ 0.108
V
3,4,7
Clock input crossing point voltage:
WCK, /WCK
VIXWCK(AC)
VREFD
- 0.10
VREFD
+ 0.10
VREFD
- 0.09
VREFD
+ 0.09
V
3,4,
8,9
0°C ≤ TC ≤ 95°C. All voltages are measured at the package pins.
This provides a minimum of 0.9V to a maximum of 1.2V, and is nominally 70% of VDDQ with POD15. If POD135, this
provides a minimum of 0.845V to a maximum of 1.045V, and is nominally 70% of VDDQ. DRAM timings relative to CK
cannot be guaranteed if these limits are exceeded.
3. For AC operations, all DC clock requirements must be satisfied as well.
4. The value of VIXCK and VIXWCK is expected to equal 70% VDDQ for the transmitting device and must track variations
in the DC level of the same.
5. VIDCK is the magnitude of the difference between the input level in CK and the input level on /CK. The input reference
level for signals other than CK and /CK is VREFC.
6. VIDWCK is the magnitude of the difference between the input level in WCK and the input level on /WCK. The input
reference level for signals other than WCK and /WCK is either VREFD, VREFD2 or the internal VREFD.
7. The CK and /CK input reference level (for timing referenced to CK and /CK) is the point at which CK and /CK cross.
Please refer to the applicable timings in the AC timings table.
8. The WCK and /WCK input reference level (for timing referenced to WCK and /WCK) is the point at which WCK and
/WCK cross. Please refer to the applicable timings in the AC Timings table.
9. VREFD is either VREFD, VREFD2 or the internal VREFD.
10. The slew rate is measured between VREFC crossing and VIXCK(AC).
11. The slew rate is measured between VREFD crossing and VIXWCK(AC).
Notes: 1.
2.
Data Sheet E1771E11 (Ver. 1.1)
12
EDW1032BBBG
3.
Package Drawing
170-ball FBGA
Solder ball: Lead free (Sn-Ag-Cu)
Unit: mm
12.0 ± 0.1
0.2 S A
14.0 ± 0.1
INDEX MARK
0.2 S B
0.2
S
1.1 ± 0.1
S
0.12 S
0.35 ± 0.05
A
B0.15 M S A B
0.8
170-B0.45 ± 0.05
12.8
B
INDEX MARK
2.0
0.8
10.4
ECA-TS2-0327-02
Data Sheet E1771E11 (Ver. 1.1)
13
EDW1032BBBG
NOTES FOR CMOS DEVICES
1
PRECAUTION AGAINST ESD FOR MOS DEVICES
Exposing the MOS devices to a strong electric field can cause destruction of the gate
oxide and ultimately degrade the MOS devices operation. Steps must be taken to stop
generation of static electricity as much as possible, and quickly dissipate it, when once
it has occurred. Environmental control must be adequate. When it is dry, humidifier
should be used. It is recommended to avoid using insulators that easily build static
electricity. MOS devices must be stored and transported in an anti-static container,
static shielding bag or conductive material. All test and measurement tools including
work bench and floor should be grounded. The operator should be grounded using
wrist strap. MOS devices must not be touched with bare hands. Similar precautions
need to be taken for PW boards with semiconductor MOS devices on it.
2
HANDLING OF UNUSED INPUT PINS FOR CMOS DEVICES
No connection for CMOS devices input pins can be a cause of malfunction. If no
connection is provided to the input pins, it is possible that an internal input level may be
generated due to noise, etc., hence causing malfunction. CMOS devices behave
differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed
high or low by using a pull-up or pull-down circuitry. Each unused pin should be connected
to VDD or GND with a resistor, if it is considered to have a possibility of being an output
pin. The unused pins must be handled in accordance with the related specifications.
3
STATUS BEFORE INITIALIZATION OF MOS DEVICES
Power-on does not necessarily define initial status of MOS devices. Production process
of MOS does not define the initial operation status of the device. Immediately after the
power source is turned ON, the MOS devices with reset function have not yet been
initialized. Hence, power-on does not guarantee output pin levels, I/O settings or
contents of registers. MOS devices are not initialized until the reset signal is received.
Reset operation must be executed immediately after power-on for MOS devices having
reset function.
CME0107
Data Sheet E1771E11 (Ver. 1.1)
14
EDW1032BBBG
The information in this document is subject to change without notice. Before using this document, confirm that this is the latest version.
No part of this document may be copied or reproduced in any form or by any means without the prior
written consent of Elpida Memory, Inc.
Elpida Memory, Inc. does not assume any liability for infringement of any intellectual property rights
(including but not limited to patents, copyrights, and circuit layout licenses) of Elpida Memory, Inc. or
third parties by or arising from the use of the products or information listed in this document. No license,
express, implied or otherwise, is granted under any patents, copyrights or other intellectual property
rights of Elpida Memory, Inc. or others.
Descriptions of circuits, software and other related information in this document are provided for
illustrative purposes in semiconductor product operation and application examples. The incorporation of
these circuits, software and information in the design of the customer's equipment shall be done under
the full responsibility of the customer. Elpida Memory, Inc. assumes no responsibility for any losses
incurred by customers or third parties arising from the use of these circuits, software and information.
[Product applications]
Be aware that this product is for use in typical electronic equipment for general-purpose applications.
Elpida Memory, Inc. makes every attempt to ensure that its products are of high quality and reliability.
However, this product is not intended for use in the product in aerospace, aeronautics, nuclear power,
combustion control, transportation, traffic, safety equipment, medical equipment for life support, or other
such application in which especially high quality and reliability is demanded or where its failure or
malfunction may directly threaten human life or cause risk of bodily injury. Customers are instructed to
contact Elpida Memory's sales office before using this product for such applications.
[Product usage]
Design your application so that the product is used within the ranges and conditions guaranteed by
Elpida Memory, Inc., including the maximum ratings, operating supply voltage range, heat radiation
characteristics, installation conditions and other related characteristics. Elpida Memory, Inc. bears no
responsibility for failure or damage when the product is used beyond the guaranteed ranges and
conditions. Even within the guaranteed ranges and conditions, consider normally foreseeable failure
rates or failure modes in semiconductor devices and employ systemic measures such as fail-safes, so
that the equipment incorporating Elpida Memory, Inc. products does not cause bodily injury, fire or other
consequential damage due to the operation of the Elpida Memory, Inc. product.
[Usage environment]
Usage in environments with special characteristics as listed below was not considered in the design.
Accordingly, our company assumes no responsibility for loss of a customer or a third party when used in
environments with the special characteristics listed below.
Example:
1) Usage in liquids, including water, oils, chemicals and organic solvents.
2) Usage in exposure to direct sunlight or the outdoors, or in dusty places.
3) Usage involving exposure to significant amounts of corrosive gas, including sea air, CL 2 , H 2 S, NH 3 ,
SO 2 , and NO x .
4) Usage in environments with static electricity, or strong electromagnetic waves or radiation.
5) Usage in places where dew forms.
6) Usage in environments with mechanical vibration, impact, or stress.
7) Usage near heating elements, igniters, or flammable items.
If you export the products or technology described in this document that are controlled by the Foreign
Exchange and Foreign Trade Law of Japan, you must follow the necessary procedures in accordance
with the relevant laws and regulations of Japan. Also, if you export products/technology controlled by
U.S. export control regulations, or another country's export control laws or regulations, you must follow
the necessary procedures in accordance with such laws or regulations.
If these products/technology are sold, leased, or transferred to a third party, or a third party is granted
license to use these products, that third party must be made aware that they are responsible for
compliance with the relevant laws and regulations.
M01E1007
Data Sheet E1771E11 (Ver. 1.1)
15
EDW1032BBBG
Revision History
Ver.
Date
1.0
Apr. 2011 Initial version
Description
1.1
Sep. 2011
Part Number Correction
Type D : Monolithc Device to Packaged Device
Data Sheet E1771E11 (Ver. 1.1)
16