EGP20A-EGP20M 2.0A Axial Leaded High Efficiency Rectifier Features · · · · · · · GPRC (Glass Passivated Rectifier Chip) inside Glass passivated cavity-free junction Superfast recovery time for high efficiency Low forward voltage , high current capability Low leakage current High surge current capability o High temperature soldering guaranteed: 260 C/10 seconds, 0.375" (9.5mm) lead length, 5lbs. (2.3 kg) tension · Plastic package has Underwriters Laboratory Flammability Classification 94V-0 B A A C D DO-15 Mechanical Data Dim Min Max A 25.40 ¾ · Case : JEDEC DO- 15 molded plastic over glass body · Terminals : Plated axial leads , solderable per MIL-STD-750, Method 2026 · Polarity : Color band denotes cathode end · Mounting Position : Any · Weight : 0.015 ounes , 0.4 gram B 5.50 7.62 C 0.686 0.889 D 2.60 3.60 All Dimensions in mm Maximum Ratings and Electrical Characteristics @ TA = 25°C unless otherwise specified o EGP20 Ratings at 25 C ambient temperature SYMBOLS unless otherwise specified. A B D F G J K M UNITS Maximum repetitive peak reverse voltage VRRM 50 100 200 300 400 600 800 1000 Volts Maximum RMS voltage VRMS 35 70 140 210 280 420 560 700 Volts VDC 50 100 200 300 400 600 800 1000 Volts Maximum DC blocking voltage Maximum average forward rectified current I (AV) Amps 2.0 0.375" (9.5mm) lead length (SEE FIG.1) Peak forward surge current 8.3ms single half sine-wave IFSM 65 60 Amps 1.7 Volts superimposed on rated load (JEDEC Method) Maximum instantaneous forward voltage at 2.0 A VF 1.0 o TA=25 C o TA=125 C o TA=150 C 1.25 IR 5 30 100 5 100 - uA Maximum reverse recovery time (NOTE 1) trr 50 75 nS Typical junction capacitance (NOTE 2) CJ Maximum DC reverse current at rated DC blocking voltage Typical thermal resistance (NOTE 3) Operating junction and storage temperature range R R pF 45 40 15 JA JL TJ,TSTG -65 to +175 NOTES : (1) Reverse recovery test condition : IF 0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient at 0.375" (9.5mm) lead lengths, P.C.B. mounted. 1 of 2 o -55 to +150 C/W o C FIG.1 - FORWARD CURRENT DERATING CURVE FIG.2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 70 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES 2.0 RESISTIVE OR INDUCTIVE LOAD 1.5 EGP20A~EGP20G EGP20J~EGP20M 1.0 0.5 0.375" (9.5mm) LEAD LENGTH 0 TJ=TJ max. 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 60 50 EGP20A~EGP20G 40 EGP20J~EGP20M 30 20 10 0 0 25 50 75 100 125 150 1 175 10 NUMBER OF CYCLES AT 60Hz FIG.3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG.4 - TYPICAL REVERSE CHARACTERISTICS o 100 10.00 PULSE WIDTH=300uS 1% DUTY CYCLE INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES IINSTANTANEOUS FORWARD CURRENT, AMPERES 100 AMBIENT TEMPERATURE, C 1.00 0.10 0.01 0.2 EGP20J~EGP20M EGP20G EGP20A~EGP20F 0.4 0.6 0.8 1.0 1.2 1.4 1.6 10 1 o TJ=125 C o TJ=150 C 0.1 0 1.8 20 40 60 80 100 110 PERCENT OF RATED PEAK REVERSE VOLTAGE,% INSTANTANEOUS FORWARD VOLTAGE, VOLTS o TJ = 25 C 100 60 40 20 10 6 4 2 1 .1 .2 .4 1.0 2 4 10 20 FIG.6 - TYPICAL TRANSIENT THERMAL IMPEDANCE 100 o JUNCTION CAPACITANCE, pF TRANSIENT THERMAL IMPEDANCE( C/W) FIG.5 - TYPICAL JUNCTION CAPACITANCE 200 40 100 10 1 0.1 0.01 0.10 1.0 10 t , PULSE DURATION, sec REVERSE VOLTAGE, VOLTS 2of2 100