www.make-ps.com E-mail:[email protected] Single & Dual Output DC/DC Converter Series LCD15 FEATURES: ● ● ● ● ● ● ● ● 15Watt | DC-DC Converter 15W DIL PACKAGE 2:1 WIDE INPUT RANGE 100% BURNED IN HIGH EFFICIENCY UL94V-0 PACKAGE MATERIAL CUSTOM SOLUTIONS AVAILABLE RoHS COMPLIANT Remote Control:On/Off APPLICATIONS: ● Wireless Network ● Telecom/Datacom ● Industry Control System ● Measurement Equipment ● Semiconductor Equipment MODEL SELECTION CHART Output Current Efficiency Full Load (mA TYP) Output Voltage Vdc Full Load (mA) %TYP 1209 1488 1453 1453 1453 1453 654 774 710 710 718 726 327 372 363 355 359 363 3.3 5 12 15 ±12 ±15 3.3 5 12 15 ±12 ±15 3.3 5 12 15 ±12 ±15 4000 3000 1250 1000 ±625 ±500 4000 3000 1250 1000 ±625 ±500 4000 3000 1250 1000 ±625 ±500 84 84 86 86 86 86 84 84 88 88 87 86 84 84 86 88 87 86 Input Current Part Number Input Voltage Vdc No-Load (mA TYP) LCD15-12S3P3 LCD15-12S05 LCD15-12S12 LCD15-12S15 LCD15-12D12 LCD15-12D15 LCD15-24S3P3 LCD15-24S05 LCD15-24S12 LCD15-24S15 LCD15-24D12 LCD15-24D15 LCD15-48S3P3 LCD15-48S05 LCD15-48S12 LCD15-48S15 LCD15-48D12 LCD15-48D15 9-18 9-18 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 18-36 18-36 36-75 36-75 36-75 36-75 36-75 36-75 120 90 40 40 40 40 50 65 20 20 20 20 40 40 15 15 15 15 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Temperature Derating Graph OutPut Power(%) Temperature Derating Graph Tolerance Envelope Graph 100 75 50 25 Nature Convection 0 -40 65 85 100 Ambient Temperature(℃) 1/3 www.make-ps.com Input Specifications E-mail:[email protected] Conditions Parameters Min Typ Max Voltage Types 12 Vin 24 Vin 48 Vin Pi Network Fuse Recommended Start-up voltage / under voltage shut down Filter Protection Output Specifications Ripple and noise(20 MHz bandwidth) 9/8 17.0 / 16.5 33.0 / 30.5 Min Typ only for single output models single output dual output single output dual output models balanced load required 0 with external capacitor see application note. 3.3VDC 5VDC 12VDC 15VDC Over voltage protection Start up time Max. capacitive load Parameters Temperature ranges Humidity Reliability, calculated MTBF Isolation voltage Isolation capacity Isolation resistance Remote On/Off Switching frequency (fixed) 3.7 5.6 13.5 16.8 nominal Vin and constant resistive load 25% load step change 3.3 & 5 VDC 12 VDC 15 VDC ±12 VDC ±15 VDC General Specifications Conditions Min -40 Operating(with derating) Case temperature Storage non condensing MIL-HDBK-217F, @ +25°C, ground benign For 60 seconds(Input/Output) Input/Output Input/Output (500 VDC) On Off Off idle current: pulse width modulation PWM Max ±2 ±10 0.5 0.5 0.5 1.0 10 100 at 150 % typ.of Iout max., constant current automatic recovery 5.4 7.0 19.6 20.5 450 250 1000 330 220 ±150 ±100 Output current limitation Short circuit protection Transient response setting time VDC VDC VDC Temperature Coefficinet:±0.05%/ ℃ Conditions Parameters Voltage Tolerance Output voltage adj. range Line Regulation (Vmin – Vmax) Load Regulation (25 %F.L– 100%F.L) Minimum load Units 2:1 Typ -55 5 560000 1000 1000 Max +85 +100 +125 95 1500 Units % % % % % % % mVp-p Vout Vout Vout Vout ms us uF uF uF uF uF Units ℃ ℃ ℃ % Hours VDC pF MΩ 3.0 ... 12 VDC or open circuit 0 ... 1.2 VDC or short circuit pin 6 and pin 2 2.5 mA 400 KHz nickel coated copper non conductive FR4 epoxy (UL 94V-0 rated) 15 g (0.53 oz) max. 265℃/ 10sec Case material Baseplate Potting material Weight Soldering temperature 2/3 www.make-ps.com E-mail:[email protected] OUTLINE DRAWING Package Style and Pinning (mm) 1. All dimensions in Inches (mm) Tolerance: X.XX±0.02 (X.X±0.5) X.XXX±0.01 (X.XX±0.25) 2. Pin pitch tolerance ±0.01(0.25) 3. Pin dimension tolerance ±0.004 (0.1) PIN CONNECTION PIN SINGLE DUAL 1 2 3 4 5 6 + INPUT - INPUT + INPUT - INPUT ON/OFF +VOUT TRIM -VOUT ON/OFF +VOUT COMMON -VOUT All specifications are typical at nominal input, nominal load and 25° C unless otherwise specified. External, low ESR, 10 microfarad (minimum) capacitor across output is recommended for operation. Make Power world-class design, development and manufacturing team stands ready to work with you to deliver the exact power converter you need for your ready to work with you to deliver the exact power converter you need for your demanding, large volume, OEM applications. And ... we ll do it on time and within budget Our experienced applications and design staffs; quick-turn prototype capability; highly automated, SMT assembly facilities; and in-line SPC quality-control techniques combine to give us the unique ability to design and deliver any quantity of power converters to the highest standards of quality and reliability. We have compiled a large library of DC/DC designs that are currently used in a variety of telecom, medical, computer, railway, aerospace and industrial applications. We may already have the converter you need. Contact us. Our goal is to provide you the highest-quality, most cost-effective power converters available. CUSTOM CAPABILITIES 3/3