SUBMINIATURE T-3/4 LED DIFFUSED AND CLEAR LAMPS HIGH EFF. RED YELLOW GREEN AIGaAs RED HLMP-6305A HLMP-6405A HLMP-6505A HLMP-Q105A HLMP-Q101A Water Clear Water Clear Water Clear Water Clear Red Diffused MV6700A MV6300A MV6400A HLMP-Q150A HLMP-Q155A Red Diffused Yellow Diffused Green Diffused Red Diffused Water Clear FEATURES PACKAGE DIMENSIONS • Subminiature T-3/4 transfer molded .087 (2.2) .079 (2.0) • Low package profile • Axial leads .276 (7.0) MIN .024 (.6) .016 (.4) • Wide viewing angle • SMT versions .091 (2.3) .083 (2.1) DIA .020 (.5) .012 (.3) .075 (1.9) .063 (1.6) .010 (.26) .002 (.06) DESCRIPTION .058 (1.48) .050 (1.28) .056 (1.44) .048 (1.24) These T-3/4 subminiature LED lamps feature a squarebase, transfer molded package for surface mount applications. A tinted diffused or water clear epoxy lens — available in AIGaAs red, high-efficiency red, green, and yellow — produces wide-angle beam emission and sharp on/off contrast. They are available with gullwing lead bends for top mounting, as well as yoke lead bends and Z-bends for mounting to the back of a PCB. .031 (.78) .023 (.58) CATHODE MARK (COLOR STRIPE ON SIDE OF PACKAGE) NOTES: ALL DIMENSIONS ARE IN INCHES (mm). ABSOLUTE MAXIMUM RATING c HLMP-6305A MV6700A HLMP-6405A MV6300A HLMP-6505A MV6400A HLMP-Q101A HLMP-Q105A HLMP-Q150A HLMP-Q155A Power Dissipation 135 85 135 85 mW Average Forward Current 30 20 30 30 mA Peak Forward Current (1 µS pulsewidth, 0.1% DF) 90 60 90 300 mA Lead Soldering Time at 260°C 5 5 5 5 sec Operating Temperature -55 to +100 -55 to +100 -50 to +100 -20 to +100 °C Storage Temperature -55 to +100 -55 to +100 -50 to +100 -20 to +100 °C Parameter © 2003 Fairchild Semiconductor Corporation Page 1 of 6 Units 7/14/03 SUBMINIATURE T-3/4 LED DIFFUSED AND CLEAR LAMPS HIGH EFF. RED YELLOW GREEN AIGaAs RED HLMP-6305A HLMP-6405A HLMP-6505A HLMP-Q105A HLMP-Q101A Water Clear Water Clear Water Clear Water Clear Red Diffused MV6700A MV6300A MV6400A HLMP-Q150A HLMP-Q155A Red Diffused Yellow Diffused Green Diffused Red Diffused Water Clear ELECTRICAL / OPTICAL CHARACTERISTICS (TA =25°C) Part Number QTLP- MV6700A MV6300A MV6400A HLMP-Q150A Minimum 1.0 1.0 1.0 1.0* Typical 3.0 3.0 3.0 1.8* Luminous Intensity (mcd) Condition IF = 10mA *Tested at IF = 1mA IF = 10mA Forward Voltage (V) Maximum 3.0 3.0 3.0 1.8* Typical 1.8 2.0 2.0 1.6* *Tested at IF = 1mA Peak Wavelength (nm) 635 585 565 660 IF = 10mA Spectral Line Half Width (nm) 40 36 28 20 IF = 10mA Reverse Voltage (V) 5 5 5 5 IR = 100µA Viewing Angle (°) 50 50 50 50 IF = 10mA ELECTRICAL / OPTICAL CHARACTERISTICS (TA =25°C) Part Number QTLP- HLMP6305A HLMP6405A HLMP6505A HLMPQ101A HLMP-Q105A/ Q155A Luminous Intensity (mcd) Condition IF = 10mA Minimum 3.0 3.0 3.0 22** 20.0**/2.0* **Tested at IF = 1mA Typical 12.0 12.0 12.0 45** 50.0**/4.0* **Tested at IF = 20mA Maximum 3.0 3.0 3.0 2.4** 2.4**/1.8* *Tested at IF = 1mA Typical 1.8 2.0 2.0 1.8** 1.8**/1.6* **Tested at IF = 20mA Peak Wavelength (nm) 635 585 565 660 660 IF = 10mA Spectral Line Half Width (nm) 40 36 28 20 20 IF = 10mA Reverse voltage (V) 5 5 5 5 5 IR = 100µA Viewing Angle (°) 25 25 25 50 25 IF = 10mA Forward Voltage (V) IF = 10mA © 2003 Fairchild Semiconductor Corporation Page 2 of 6 7/14/03 SUBMINIATURE T-3/4 LED DIFFUSED AND CLEAR LAMPS HIGH EFF. RED YELLOW GREEN AIGaAs RED HLMP-6305A HLMP-6405A HLMP-6505A HLMP-Q105A HLMP-Q101A Water Clear Water Clear Water Clear Water Clear Red Diffused MV6700A MV6300A MV6400A HLMP-Q150A HLMP-Q155A Red Diffused Yellow Diffused Green Diffused Red Diffused Water Clear TYPICAL PERFORMANCE CURVES Fig. 2 Relative Luminous Intensity vs. DC Forward Current Fig. 1 Forward Current vs. Forward Voltage 2.5 90 RELATIVE LUMNOUS INTENSITY (NORMALIZED AT 10 mA) IF - FORWARD CURRENT (mA) 80 AlGaAs RED 70 60 HER 50 YELLOW 40 30 20 10 0 1.0 2.0 HER YELLOW GREEN 1.5 1.0 AlGaAs RED 0.5 GREEN 0.0 2.0 3.0 4.0 5.0 0 5 VF - FORWARD VOLTAGE (V) 10 15 IF - DC FORWARD CURRENT (mA) Fig. 3 Relative Intensity vs. Peak Wavelength 1.0 RELATIVE INTENSITY GREEN AlGaAs RED YELLOW 0.5 HER 0 500 550 600 650 700 750 WAVELENGTH (nm) © 2003 Fairchild Semiconductor Corporation Page 3 of 6 7/14/03 SUBMINIATURE T-3/4 LED DIFFUSED AND CLEAR LAMPS HIGH EFF. RED YELLOW GREEN AIGaAs RED HLMP-6305A HLMP-6405A HLMP-6505A HLMP-Q105A HLMP-Q101A Water Clear Water Clear Water Clear Water Clear Red Diffused MV6700A MV6300A MV6400A HLMP-Q150A HLMP-Q155A Red Diffused Yellow Diffused Green Diffused Red Diffused Water Clear RECOMMENDED PRINTED CIRCUIT BOARD PATTERN 0.106 (2.68) 0.035 (0.89) 0.035 (0.89) 0.035 (0.89) For Gullwing Lead Bend RECOMMENDED REFLOW SOLDERING PROFILE 5 sec MAX soldering time 240° C MAX +5° C/s MAX -5° C/s MAX 60 - 120 sec Preheating 120 - 150° C MAX © 2003 Fairchild Semiconductor Corporation Page 4 of 6 7/14/03 SUBMINIATURE T-3/4 LED DIFFUSED AND CLEAR LAMPS HIGH EFF. RED YELLOW GREEN AIGaAs RED HLMP-6305A HLMP-6405A HLMP-6505A HLMP-Q105A HLMP-Q101A Water Clear Water Clear Water Clear Water Clear Red Diffused GULLWING LEAD CONFIGURATION MV6700A MV6300A MV6400A HLMP-Q150A HLMP-Q155A Red Diffused Yellow Diffused Green Diffused Red Diffused Water Clear FEATURES .087 (2.2) .079 (2.0) • Available in Gullwing, Yoke and Z-bend lead formings • Compatible with automatic placement equipment ANODE CATHODE • Compatible with vapor phase reflow soldering processes .091 (2.3) .083 (2.1) • Long life — solid state reliability • Reel and tape or bulk packaging available .024 (.6) .016 (.4) .020 (.5) .012 (.3) .154 (3.90) .148 (3.75) DESCRIPTION These subminiature solid state lamps are transfer molded in an axial lead package. They are available in yellow, green, high efficiency red and AIGaAs red in both diffused and water clear lens. .078 (1.9) .063 (1.6) .115 (2.92) .099 (2.52) .058 (1.48) .050 (1.28) .010 (.26) .002 (.06) Automatic placement equipment can be used to mount the LEDs on the PC board. The lamps can be mounted using either batch or in line vapor phase reflow solder processes. NOTES: .033 (.82) .000 (.00) .016 (.4) .008 (.2) .039 (1.0) .028 (.7) ALL DIMENSIONS ARE IN INCHES (mm) YOKE LEAD CONFIGURATION .087 (2.2) .079 (2.0) .020 (.5) .012 (.3) .087 (2.2) .079 (2.0) ANODE CATHODE .091 (2.3) .083 (2.1) .091 (2.3) .083 (2.1) .024 (.6) .016 (.4) .024 (.6) .016 (.4) CATHODE .300 (7.62) MAX .078 (1.9) .063 (1.6) .115 (2.92) .099 (2.52) Z-BEND LEAD CONFIGURATION .058 (1.48) .050 (1.28) .117 (2.96) .100 (2.56) © 2003 Fairchild Semiconductor Corporation .240 (6.1) .232 (5.9) .020 (.5) .012 (.3) ANODE .128 (3.24) .112 (2.84) .047 (1.2) .031 (0.8) .010 (.26) .002 (.06) .039 (.99) .023 (.59) .078 (1.9) .063 (1.6) .033 (.85) .026 (.65) .048 (1.22) .032 (.82) .058 (1.48) .050 (1.28) .033 (.85) .026 (.66) Page 5 of 6 .010 (.26) .002 (.06) .189 (4.8) .173 (4.4) .034 (.86) .026 (.66) 7/14/03 SUBMINIATURE T-3/4 LED DIFFUSED AND CLEAR LAMPS HIGH EFF. RED YELLOW GREEN AIGaAs RED HLMP-6305A HLMP-6405A HLMP-6505A HLMP-Q105A HLMP-Q101A Water Clear Water Clear Water Clear Water Clear Red Diffused MV6700A MV6300A MV6400A HLMP-Q150A HLMP-Q155A Red Diffused Yellow Diffused Green Diffused Red Diffused Water Clear DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. © 2003 Fairchild Semiconductor Corporation 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Page 6 of 6 7/14/03