TI BUF01901AIDRCRG4 Programmable voltage source with memory Datasheet

BUF01900
BUF01901
SBOS337A − OCTOBER 2006 − REVISED OCTOBER 2006
Programmable Voltage Source
with Memory
FEATURES
DESCRIPTION
D
D
D
D
D
D
D
D
The BUF01900 and BUF01901 provide a programmable
voltage output with 10-bit resolution. Programming of the
output occurs through an industry-standard, two-wire
serial interface. Once the correct VCOM voltage is
established it can easily be stored into the integrated
nonvolatile memory.
10-BIT RESOLUTION
RAIL-TO-RAIL OUTPUT
ONBOARD NONVOLATILE MEMORY
IOUT: 100mA
LOW SUPPLY CURRENT: 900µA
An initial output voltage and adjustment range can be set
by an external resistor-divider. With its large output current
capability (up to 100mA), the BUF01900 and BUF01901
are ideally suited as programmable VCOM calibrators in
LCD panels.
SUPPLY VOLTAGE: 7V to 18V
DIGITAL SUPPLY: 2.0V to 5.5V
INDUSTRY-STANDARD, TWO-WIRE
INTERFACE
The BUF01901 has the digital-to-analog converter (DAC)
output brought out directly. It has a slightly lower cost than
the BUF01900, and works very well with the integrated
VCOM in traditional gamma buffers such as the BUFxx702,
BUFxx703, BUFxx704 and BUF11705.
D HIGH ESD RATING:
2kV HBM, 500V CDM
The BUF01900 and BUF01901 are both available in
TSSOP-8 and 3mm x 3mm DFN-10 packages. The
DFN-10 package (only 0.9mm in height) is especially
well-suited for notebook computers. Both devices are
specified from −40°C to +85°C.
APPLICATIONS
D LCD PANEL VCOM CALIBRATION
D LCD PANEL BRIGHTNESS AND CONTRAST
CONTROL
POTENTIOMETER REPLACEMENT
Digital
2V to 5.5V
MOTOR DRIVE
Analog
7V to 18V
BIAS
PROGRAMMABLE POWER SUPPLY
BUF01900
PROGRAMMABLE OFFSET ADJUSTMENT
ACTUATOR CONTROL
BUF01900, BUF01901 RELATED PRODUCTS
FEATURES
PRODUCT
22V High Supply Voltage Gamma Buffers
BUF11705
12--Channel Programmable Buffer, 10-Bit, VCOM
BUF12800
20-Channel Programmable Buffer, 10-Bit, VCOM
BUF20800
16-Channel Programmable Buffer with Memory
BUF16820
20-Channel Programmable Buffer with Memory
BUF20820
Program Command
D
D
D
D
D
Voltage
Regulator
250kΩ
4 x OTP
ROM
Switch
Control
10−Bit
DAC
Buffer
VCOM
Input Control Logic
SDA SCL A0
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments
semiconductor products and disclaimers thereto appears at the end of this data sheet.
PowerPAD is a registered trademark of Texas Instruments. All other trademarks are the property of their respective owners.
Copyright  2006, Texas Instruments Incorporated
! ! www.ti.com
"#$%&$$
"#$%&$%
www.ti.com
SBOS337A − OCTOBER 2006 − REVISED OCTOBER 2006
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate
precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ABSOLUTE MAXIMUM RATINGS(1)
Supply Voltage, VS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +20V
Supply Voltage, VSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +6V
Signal Input Terminals,
BIAS:
Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5V to VS +0.5V
SCL, SDA, A0, A1:
Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5V to +6V
Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±10mA
Output Short Circuit(2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous
Operating Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to +95°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to +150°C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +125°C
ESD Rating:
Human Body Model (HBM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000V
Charged-Device Model (CDM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500V
(1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade
device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is
not supported.
(2) Short-circuit to ground.
ORDERING INFORMATION(1)
PRODUCT
PACKAGE-LEAD
PACKAGE DESIGNATOR
PACKAGE MARKING
BUF01900
DFN-10
DRC
BOO
BUF01900
TSSOP-8
PW
F01900
BUF01901
DFN-10
DRC
BOP
BUF01901
TSSOP-8
PW
F01901
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI web site
at www.ti.com.
PIN CONFIGURATIONS
BUF01901
BUF01900
VS
1
VCOM
2
BIAS
3
GND
4
DGND
5
Exposed
Thermal
Die Pad
on
Underside
SDA
VS
1
9
SCL
NC
2
8
A0
BIAS
3
7
A1
GND
4
6
VSD
DGND
5
Exposed
Thermal
Die Pad
on
Underside
DFN−10
DFN−10
BUF01900
BUF01901
VS
1
8
SDA
VC OM
2
7
SCL
BIAS
3
6
A0
GND
4
5
VSD
GND
TSSOP−8
2
10
NC = No connection
10
SDA
9
SCL
8
A0
7
A1
6
V SD
VS
1
8
SDA
NC
2
7
SCL
BIAS
3
6
A0
4
5
VSD
TSSOP−8
"#$%&$$
"#$%&$%
www.ti.com
SBOS337A − OCTOBER 2006 − REVISED OCTOBER 2006
ELECTRICAL CHARACTERISTICS
Boldface limits apply over the specified temperature range, TA = −40°C to +85°C.
At TA = +25°C, VS = 18V, VSD = 5V, RL = 1.5kΩ connected to ground, and CL = 200pF, unless otherwise noted.
BUF01900, BUF01901
PARAMETER
ANALOG
VCOM Output Swing(1)
VCOM Output Reset and Power-Up Value(1)
Nominal VBIAS Output Impedance
Program to Out Delay
Output Accuracy
Load Regulation
VCOM(1)
Offset
Offset Drift
Common-Mode Range
Common-Mode Rejection
Slew Rate
VBIAS
Integral Nonlinearity
Differential Nonlinearity
Gain Error
Accuracy
ANALOG POWER SUPPLY
Operating Range(2)
Total Analog Supply Current
over Temperature
DIGITAL
Logic 1 Input Voltage
Logic 0 Input Voltage
Logic 0 Output Voltage
Input Leakage
Clock Frequency
DIGITAL POWER SUPPLY
Operating Voltage Range
Digital Supply Current(2)
over Temperature
TEMPERATURE
Specified Temperature Range
Operating Temperature Range
Storage Temperature Range
Thermal Resistance
TSSOP-8
DFN-10
CONDITIONS
MIN
TYP
Sourcing 10mA, Code 1023
Sinking 10mA, Code 00
Sourcing 100mA, Code 1023
Sinking 100mA, Code 00
OTP not programmed, Code 512
No Load on VBIAS, VCOM
17.7
17.8
0.6
16
0.75
VS/2
250
5
20
0.5
15
tD
REG
1V < VCOM < 17.7
VOUT = VS/2, IOUT = +50mA to −50mA Step
−25°C to +100°C
CMR
0.8V < VIN < 17.9V
MAX
1
1
50
1.5
UNIT
V
V
V
V
V
kΩ
µs
mV
mV/mA
±5
5
0.8 to 18
85
5
±25
mV
µV/°C
V
dB
V/µs
0.1
0.1
0.1
20
2
2
1
50
LSB
LSB
%FSC
mV
0.9
18
1.5
1.5
V
mA
mA
0.15
±0.01
0.3 × VSD
0.4
±10
400
3.4
V
V
V
µA
kHz
MHz
No Load on VBIAS
INL
DNL
VS
IS
7
Output at Reset Values, No Load
0.7 × VSD
VIH
VIL
VOL
fCLK
ISINK = 3mA
Standard/Fast Mode
High-Speed Mode
VSD
ISD
2.0
25
100
Junction Temperature < 125°C
−40
−40
−65
5.5
50
V
µA
µA
+85
+95
+150
°C
°C
°C
qJA
150
47
°C/W
°C/W
(1) BUF01900 only.
(2) Minimum analog supply voltage is 8.5V when programming OTP memory.
3
"#$%&$$
"#$%&$%
www.ti.com
SBOS337A − OCTOBER 2006 − REVISED OCTOBER 2006
TYPICAL CHARACTERISTICS
At TA = +25°C, VS = 18V, VSD = 5V, RL = 1.5kΩ connected to ground, and CL = 200pF, unless otherwise noted.
ANALOG SUPPLY CURRENT vs TEMPERATURE
DIGITAL SUPPLY CURRENT vs TEMPERATURE
50
Digital Supply Current (µA)
Analog Supply Current (mA)
1.5
VS = 18V
1.0
VSD = 8V
0.5
40
VSD = 5V
30
20
VSD = 2V
10
0
0
−40
−20
0
20
40
60
80
−40
100
−20
0
Temperature (_ C)
Figure 1
PDS limits are ±25mV
16
10
14
5
12
0
−5
6
4
−20
Sourcing, Code = 3FFh
8
−15
2
0
20
40
60
80
Sinking, Code = 000h
0
100
0
Temperature (_C)
25
75
100
Figure 4
DIFFERENTIAL NONLINEARITY ERROR
vs INPUT CODE
INTEGRAL NONLINEARITY ERROR vs INPUT CODE
1.5
1.5
1.0
1.0
DNL Error (LSB)
INL Error (LSB)
50
IOUT (mA)
Figure 3
0.5
0
−0.5
−1.0
0.5
0
−0.5
−1.0
10 Typical Units Shown
10 Typical Units Shown
−1.5
−1.5
0
128
256
384
512
640
Input Code
Figure 5
4
100
10
−10
−20
80
VS = 18V
18
15
−25
−40
60
OUTPUT VOLTAGE vs OUTPUT CURRENT
20
VOUT (V)
VOS (mV)
20
40
Figure 2
BUFFER OFFSET VOLTAGE vs TEMPERATURE
(VS = 18V, VSD = 5V)
25
20
Temperature (_ C)
768
896
1024
0
128
256
384
512
640
Input Decimal Code
Figure 6
768
896
1024
"#$%&$$
"#$%&$%
www.ti.com
SBOS337A − OCTOBER 2006 − REVISED OCTOBER 2006
TYPICAL CHARACTERISTICS (cont)
At TA = +25°C, VS = 18V, VSD = 5V, RL = 1.5kΩ connected to ground, and CL = 200pF, unless otherwise noted.
VCOM BUFFER SLEW RATE
BUFFER LARGE SIGNAL STEP RESPONSE
(2) VCOM
(1) VBIAS
(1) VBIAS
5V/div
5V/div
(2) VCOM
1
2
1
Time (1µs/div)
Time (1µs/div)
Figure 7
Figure 8
LOAD REGULATION vs CAPACITANCE
LOAD REGULATION vs CAPACITANCE
1
1
C
10 Ω
100mA/div
100mA/div
2.7nF
2
2 .7 nF
C
C = 1µF
500mV/div
C = 0.1µF
500mV/div
2
C = 1µF
1
C = 10µF
2
C = 0.1µF
C = 10µF
C = 1µF
1
C = 10µF
Time (1µs/div)
Time (1µs/div)
Figure 9
Figure 10
LOAD REGULATION WITH 100µF CAPACITOR
LOAD REGULATION WITH 10µF CAPACITOR
1
1
2.7nF
100mA/div
100 µ F
50mV/div
20mV/div
100mA/div
2.7nF
1
Time (1µs/div)
Figure 11
10 µ F
1
Time (1µs/div)
Figure 12
5
"#$%&$$
"#$%&$%
www.ti.com
SBOS337A − OCTOBER 2006 − REVISED OCTOBER 2006
TYPICAL CHARACTERISTICS (cont)
At TA = +25°C, VS = 18V, VSD = 5V, RL = 1.5kΩ connected to ground, and CL = 200pF, unless otherwise noted.
LOAD REGULATION WITH 1µF CAPACITOR
(C = 1µF, RS = 0, 100mV Res.)
1
100mV/div
100mA/div
2. 7nF
1µF
1
Time (1µs/div)
Figure 13
6
"#$%&$$
"#$%&$%
www.ti.com
SBOS337A − OCTOBER 2006 − REVISED OCTOBER 2006
APPLICATIONS INFORMATION
BUF01900: ON-CHIP BUFFER
OVERVIEW
Unlike many programmable VCOM calibrators on the market, the BUF01900 offers an integrated VCOM buffer with
high current output drive capability. The output is capable
of delivering peak currents over 100mA to within 4V from
the positive supply and to within 2V from the negative supply. Using this option is very cost-effective and convenient
in systems that do not use multi-channel gamma buffers
with integrated VCOM drive. Figure 15 shows the
BUF01900 in a typical configuration.
The BUF0190x family of products consists of a 10-bit digital-to-analog converter (DAC) that is programmed through
an industry-standard two-wire interface. It contains onchip nonvolatile memory that stores a specific DAC value
that is read at power-up. The BUF0190x family consists of
two devices: The BUF01900 contains a voltage buffer that
is capable of driving high-current; the BUF01901 is a lower-cost version without the buffer. The BUF0190x is especially well-suited for VCOM calibration in LCD panels; however, it can also be used in many other applications.
Figure 14 shows the BUF01900 in a typical configuration.
VS
0.1µF
BUF01900
10µF
+
VS
SDA
2
VCOM
SCL
7
3
VBIAS
A0
6
4
GND
VSD
5
1
8
Timing
Controller
(1)
VCOM
(2)
VS
(2)
10kΩ
10kΩ
VSD
0.1µF
NOTES: (1) Optional −may be needed for stability.
(2) Optional −see application text for component selection.
Figure 14. Typical Application Diagram
Digital
2V to 5.5V
Analog
7V to 18V
R2
R1
BIAS
Program Command
BUF01900
Voltage
Regulator
250kΩ
4 x OTP
ROM
Switch
Control
10−Bit
DAC
VCOM
Buffer
VCOM
Panel
Input Control Logic
SDA SCL A0
Figure 15. BUF01900 Typical Configuration
7
"#$%&$$
"#$%&$%
www.ti.com
SBOS337A − OCTOBER 2006 − REVISED OCTOBER 2006
BUF01901: USING EXTERNAL VCOM BUFFER
Many LCD panel modules use gamma buffers, such as
TI’s BUFxx704, BUFxx703, BUF11702 and the new
BUF11705, that already include an integrated VCOM driver.
Some other LCD modules use more complicated compensation schemes that require an external high-speed
VCOM op amp. BUF01901 is optimized for lowest cost and
is intended to be used with an external VCOM buffer or op
amp. Figure 16 illustrates a typical configuration of the
BUF01901 with the BUF11705.
ON-CHIP NONVOLATILE MEMORY
The BUF0190x is optimized for the smallest die size available and consequently the lowest cost to support high vol-
ume production. The on-chip OTP (one-time-programmable) memory helps to achieve significant die size
reduction over EEPROM memory technology. This reduction is partly because of the smaller area of the OTP
memory cell, but also a result of the fact that an EEPROM
requires a high programming voltage typically generated
with an onboard charge pump. OTP memory technology
does not require the higher programming voltage; consequently, no charge pump is needed, resulting in a smaller
and lower-cost solution.
During production, the VCOM voltage is typically adjusted
only once. However, to allow for programming errors and
rework, the BUF0190x supports a total of four write cycles
to the OTP memory. This capacity means that the previously programmed code in the OTP can be overwritten
a total of three times.
BUF11704
Gamma
References
Digital
2V to 5.5V
Analog
7V to 18V
Program Command
BUF01901
Voltage
Regulator
R1
250kΩ
4 x OTP
ROM
Switch
Control
10−Bit
DAC
BIAS
VCOM
R2
Input Control Logic
SDA SCL A0
Figure 16. BUF01901 Typical Configuration
8
"#$%&$$
"#$%&$%
www.ti.com
SBOS337A − OCTOBER 2006 − REVISED OCTOBER 2006
POWER-SUPPLY VOLTAGE
The BUF0190x can be powered using an analog supply
voltage from 7V to 18V, and a digital supply from 2V to
5.5V. The digital supply must be applied prior to the analog
supply to avoid excessive current and power consumption.
During programming of the OTP, the analog power supply
must be at least 8.5V.
BUFFER INPUT AND OUTPUT RANGE
The integrated buffer has a single p-channel input stage.
The input range includes the positive supply and extends
down to typically 0.8V above the negative supply (GND).
In a typical LCD application, this is normally sufficient because the nominal VCOM level is often close to V2/2 and,
therefore, fairly far away from either supply rail. In addition,
the adjustment range is usually not much larger than 1V in
either direction of the nominal VCOM voltage. In applications requiring a wider output swing, the output voltage to
the buffer should be limited to approximately 0.8V above
the negative power supply to keep the buffer input stage
in its linear operating region. For lower input voltages, the
output results might not be valid; however, they will also
not lead to damage of the device.
The Rail-to-Rail output stage is designed to drive large
peak currents greater than 100mA.
TWO-WIRE BUS OVERVIEW
The BUF0190x communicates through an industry-standard, two-wire interface to receive data in slave mode. This
standard uses a two-wire, open-drain interface that supports multiple devices on a single bus. Bus lines are driven
to a logic low level only. The device that initiates the communication is called a master, and the devices controlled
by the master are slaves. The master generates the serial
clock on the clock signal line (SCL), controls the bus access, and generates START and STOP conditions.
To address a specific device, the master initiates a START
condition by pulling the data signal line (SDA) from a HIGH
to LOW logic level while SCL is HIGH. All slaves on the bus
shift in the slave address byte, with the last bit indicating
whether a read or write operation is intended. During the
ninth clock pulse, the slave being addressed responds to
the master by generating an Acknowledge and pulling
SDA LOW.
Data transfer is then initiated and eight bits of data are
sent, followed by an Acknowledge bit. During data transfer, SDA must remain stable while SCL is HIGH. Any
change in SDA while SCL is HIGH will be interpreted as a
START or STOP condition.
Once all data has been transferred, the master generates
a STOP condition, indicated by pulling SDA from LOW to
HIGH while SCL is HIGH.
The BUF0190x can act only as a slave device; therefore,
it never drives SCL. The SCL is only an input for the
BUF0190x.
ADDRESSING THE BUF01900 AND
BUF01901
The address of the BUF0190x in the TSSOP-8 package
is 111011x, where x is the state of the A0 pin. When the
A0 pin is LOW, the device acknowledges on address 76h.
If the A0 pin is HIGH, the device acknowledges on address
77h. Table 1 summarizes device addresses.
Table 1. Quick-Reference Table of Addresses
DEVICE/COMPONENT
ADDRESS
TSSOP Package:
A0 pin is LOW
(device will acknowledge on address 76h)
1110110
A0 pin is HIGH
(device will acknowledge on address 77h)
1110111
DFN Package:
A0 pin is LOW, A1 is LOW
(device will acknowledge on address 74h)
1110100
A0 pin is HIGH, A1 is LOW
(device will acknowledge on address 75h)
1110101
A0 pin is LOW, A1 is HIGH
(device will acknowledge on address 76h)
1110110
A0 pin is HIGH, A1 is HIGH
(device will acknowledge on address 77h)
1110111
The address of the BUF0190x in the DFN-10 package is
11101yx, where x is the state of the A0 pin and y is the state
of the A1 pin. When the A0 and A1 pins are both LOW, the
device acknowledges on address 74h. If the A0 is HIGH
and A1 is LOW, the device acknowledges on address 75h.
When the A0 is LOW, and A1 is HIGH, the device acknowledges on address 76h. If the A0 and A1 pins are both
HIGH, the device address is 77h.
Other addresses are possible through a simple mask
change. Contact your TI representative for ordering information and availability.
9
"#$%&$$
"#$%&$%
www.ti.com
SBOS337A − OCTOBER 2006 − REVISED OCTOBER 2006
DATA RATES
READ/WRITE OPERATIONS:
The two-wire bus operates in one of three speed modes:
Read commands are performed by setting the read/write
bit HIGH. Setting the read/write bit LOW performs a write
transaction.
D
D
D
Standard: allows a clock frequency of up to 100kHz;
Fast: allows a clock frequency of up to 400kHz; and
High-speed mode (or Hs mode): allows a clock
frequency of up to 3.4MHz.
Figure 17 and Figure 18 show the timing diagrams for read
and write operations.
Writing:
The BUF0190x is fully compatible with all three modes. No
special action is required to use the device in Standard or
Fast modes, but High-speed mode must be activated. To
activate High-speed mode, send a special address byte of
00001xxx, with SCL ≤ 400kHz, following the START condition; xxx are bits unique to the Hs-capable master, which
can be any value. This byte is called the Hs master code.
(Note that this is different from normal address bytes—the
low bit does not indicate read/write status.) The BUF0190x
will respond to the High-speed command regardless of the
value of these last three bits. The BUF0190x does not acknowledge this byte; the communication protocol prohibits
acknowledgment of the Hs master code. On receiving a
master code, the BUF0190x switches on its Hs mode filters, and communicates at up to 3.4MHz.
Additional high-speed transfers may be initiated without
resending the Hs mode byte by generating a repeat
START without a STOP. The BUF0190x switches out of Hs
mode with the next STOP condition.
To write to the DAC register:
1.
Send a START condition on the bus.
2.
Send the device address and read/write bit = LOW.
The BUF01900/BUF01901 will acknowledge this
byte.
3.
Send two bytes of data for the DAC register. Begin by
sending the most significant byte (bits D15—D8; only
bits D9 and D8 are used, and D15—D13 must not be
010 or 001), followed by the least significant byte (bits
D7—D0). The register is updated after receiving the
second byte.
4. Send a STOP condition on the bus.
The BUF0190x acknowledges each data byte. If the master terminates communication early by sending a STOP or
START condition on the bus, the DAC output will not update.
Reading:
To read the register of the DAC:
GENERAL CALL RESET AND POWER-UP
The BUF0190x responds to a General Call Reset, which
is an address byte of 00h (0000 0000) followed by a
data byte of 06h (0000 0110). The BUF0190x acknowledges both bytes. Upon receiving a General Call Reset,
the BUF0190x performs a full internal reset, as though it
had been powered off and then on. It always acknowledges
the
General
Call
address
byte
of
00h (0000 0000), but does not acknowledge any General
Call data bytes other than 06h (0000 0110).
The BUF0190x automatically performs a reset upon power-up. As part of the reset, the BUF0190x is configured for
the output to change to the programmed OTP memory value, or to mid-scale, ‘1000000000’, if the OTP value has not
been programmed. Table 2 provides a summary of command codes.
Table 2. Quick-Reference Table of Command
Codes
COMMAND
CODE
General Call Reset
Address byte of 00h followed by a data byte
of 06h.
High-Speed Mode
00001xxx, with SCL ≤ 400kHz; where xxx
are bits unique to the Hs-capable master.
This byte is called the Hs master code.
10
1.
Send a START condition on the bus.
2.
Send the device address and read/write bit = HIGH.
The BUF0190x will acknowledge this byte.
3.
Receive two bytes of data. The first received byte is
the most significant byte (bits D15—D8; only bits D9
and D8 have meaning, and bits D15—D12 will show
the programming status of the OTP memory). See
Table 3. The next byte is the least significant byte (bits
D7—D0).
4.
Acknowledge after receiving the first byte only.
5.
Do not acknowledge the second byte of data or send
a STOP condition on the bus.
Communication may be terminated by the master by
sending a premature STOP or START condition on the
bus, or by not sending the Acknowledge.
Table 3. OTP Memory Status
CODE
(Bits D15 − D12)
OTP PROGRAMMING STATUS
0000
OTP has not been programmed.
0001
OPT has been programmed once.
0011
OTP has programmed twice.
0111
OPT has programmed three times.
1111
OTP has programmed all four times.
"#$%&$$
"#$%&$%
www.ti.com
SBOS337A − OCTOBER 2006 − REVISED OCTOBER 2006
ACQUIRE OF OTP MEMORY
An acquire command updates the DAC output to the value
stored in OTP memory. If the OTP memory has not been
programmed, the DAC output code is ‘0000000000’.
Write commands are performed by setting the read/write
bit LOW.
To write to OTP memory:
1.
Send a START condition on the bus.
Figure 19 shows the timing diagram for the acquire
command.
2.
Send the device address and read/write bit = LOW.
The BUF0190x acknowledges this byte.
Acquire Command
3.
Send two bytes of data for the OTP memory. Begin by
sending the most significant byte first (bits D15—D8,
of which only bits D9 and D8 are data bits, and bits
D15—D13 must be 010), followed by the least
significant byte (bits D7—D0). The register updates
after receiving the second byte.
4.
Send a STOP condition on the bus.
1.
Send a START condition on the bus.
2.
Send the device address and read/write bit = LOW.
The device will acknowledge this byte.
3.
Send the acquire command. Bits D7—D5 must be
set to 001. Bits D4—D0 do not have meaning. This
byte will be acknowledged.
4.
Send a STOP condition on the bus.
Writing OTP Memory
The BUF0190x is able to write to the OTP memory a maximum of four times. Writing to the OTP memory a fourth
time uses all available memory and disables the ability to
perform additional writes (see table 3). A reset or acquire
command updates the DAC output to the most recently
written OTP memory value.
When programming the OTP memory, the analog supply
voltage must be between 8.5V and 18V.
The BUF0190x acknowledges each data byte. If the master terminates communication early by sending a STOP or
START condition on the bus, the specified OTP register
will not be updated. Writing an OTP register updates the
DAC output voltage.
Programming timing is taken from the two-wire bus.
Therefore, the master must provide correct timing on the
bus to ensure data is successfully written into OTP
memory. Figure 20 shows the timing requirements for timing when the OTP write supply and OTP write signal are
active.
11
12
Figure 17. Timing Diagram for Write DAC Register
A4
A3
A2
A1
A0
A2
A2
A1
A1
A0
A0
Write
W
Ackn
Ackn
A6
A6
SDA_in
Device_out
SCL
A5
A5
A4
A4
A3
A2
A1
A0
R
R
Ackn
Ackn
D15
D15
CODE
0000
0001
0011
0111
1111
D15
D15
Ackn
A3
A3
W
Read operation
Device address
A5
A4
Start
A6
Device_out
A5
Read DAC Register.
A6
SDA_in
SCL
D13
D13
D12
D12
D11
D11
D10
D10
D14
D14
D12
D12
D11
D11
D10
D10
OTP Programming Status
OTP has not been programmed
OTP has been programmed once
OTP has been programmed twice.
OTP has been programmed three times.
OTP has been programmed four times.
D13
D13
D9
D9
D9
D9
DAC MSbyte. D15 −D12 show the program status.
D14
D14
DAC MSbyte. D15 −D13 = ’000’D12 −D10 have no meaning.
Write operation
Ackn
Write
Start
Device address
Write DAC Register.
D8
D8
D8
D8
D7
D7
Ackn
D7
D7
Ackn
Ackn
Ackn
Ackn
Ackn
D5
D5
D6
D6
D5
D5
DAC LSbyte.
D6
D6
DAC LSbyte.
D4
D4
D4
D4
D3
D3
D3
D3
D2
D2
D2
D2
D0
D0
Ackn
Ackn
D1
D1
D0
D0
Stop
Stop
No Ackn
No Ackn
The entire DAC Register D9 −D0
is updated in this moment.
D1
D1
Ackn
"#$%&$$
"#$%&$%
SBOS337A − OCTOBER 2006 − REVISED OCTOBER 2006
www.ti.com
Figure 18. Timing Diagram for Read DAC Register
Figure 19. Timing Diagram for Acquire Command
A3
A2
A0
A2
A6
A6
SDA_in
Device_out
SCL
A5
A5
A4
A4
A1
A0
A3
A2
A1
A0
W
W
Ackn
Ackn
A1
A0
W
W
Ackn
Ackn
D15
D7
D14
D6
D15
D15
D14
D14
D13
D13
D12
D12
D11
D11
D10
D10
D9
D9
D8
D8
D13
D5
Ackn
Ackn
Ackn
D12
D4
D7
D7
D11
D3
D6
D6
D8
D0
Ackn
Ackn
Ackn
D5
D5
D4
D4
Stop
D3
D3
D2
D2
D0
D0
t1
Ackn
Ackn
Ackn
t2
Stop
The OTP Register D9 −D0
is updated in this moment.
t1: > 20µs before falling edge of clock.
t2: minimum 100µs, maximum 2ms.
D1
D1
Write supply active
Write signal active
DAC output is
updated in this moment.
D9
D1
DAC LSbyte.
D10
D2
D15 −D13 must be ’001’. D12 −D8 have no meaning.
DAC MSbyte. D15 −D13 must be 010. D12 −D10 have no meaning.
Ackn
Write
A3
Start
A1
A4
A4
Write operation
A2
A5
A5
Write OTP memory.
A3
A6
Device_out
Device address
A6
SDA_in
SCL
Write operation
Ackn
Write
Start
Device address
Acquire command.
"#$%&$$
"#$%&$%
www.ti.com
SBOS337A − OCTOBER 2006 − REVISED OCTOBER 2006
Figure 20. Timing Diagram for Write OTP Register
13
"#$%&$$
"#$%&$%
www.ti.com
SBOS337A − OCTOBER 2006 − REVISED OCTOBER 2006
VCOM CALIBRATION
The BUF0190x provides a simple, time- and cost-efficient
means to adjust the flicker performance of LCD panels either manually or automatically during the final stages of the
LCD panel manufacturing process.
The 10-bit adjustment resolution of the BUF0190x exceeds the typical adjustment resolution of existing VCOM
calibrators significantly. As with a traditional VCOM adjustment, which uses a mechanical potentiometer and a voltage divider for adjustment (see Figure 21), the BUF0190x
uses an external voltage divider that is used to set the initial VCOM voltage as well as the adjustment range.
(a) Code 00h equivalent circuit.
BUF0190x
VS
R1
(1)
VCOM
VBIAS
250kΩ
R2
(b) Code 3FFh equivalent circuit.
BUF0190x
VS
AVDD
RA
250kΩ
VS
R1
(1)
VBIAS
RB
VCOM
R2
VCOM
RC
NOTE: (1) Integrated into BUF01900 or external.
Figure 21. Traditional VCOM Adjustment
As Figure 22 shows, the 10-bit DAC acts as a Rail-to-Rail
output voltage source with a nominal 250kΩ of output impedance. For example, at Code 000h, the lowest VCOM
voltage is achieved since the 250kΩ impedance is now in
parallel with R2, which lowers the impedance of the lower
side of the voltage divider. Consequently, code 3FFh results in the highest adjustable VCOM voltage.
Once the desired output level is obtained, the part can
store the final setting using the non-volatile on-chip
memory. See Programming section for detailed information.
14
Figure 22. Simplified Block Diagram for VCOM
Adjustment using BUF0190x
SELECTING THE ADJUSTMENT STEP SIZE
A maximum of 1024 adjustment steps can be realized with
the BUF0190x, leading to very high adjustment resolution
and very small step sizes. This flexibility can be advantageous during the panel development phase. In a practical
production setting, however, this capability might lead to
adjustment times that can be too long. A simple solution is
to increase the step size between settings to more practical values for mass production. Limiting the number of adjustment steps between code 000h and code 3FFh to between 16 and 128 has been shown to typically yield
acceptable adjustment results in the smallest amount of
adjustment time.
"#$%&$$
"#$%&$%
www.ti.com
SBOS337A − OCTOBER 2006 − REVISED OCTOBER 2006
EXTERNAL VOLTAGE DIVIDER RESISTOR
SELECTION
The external resistive voltage-divider consisting of R1 and
R2 (see Figure 16, Figure 17, and Figure 18) sets both the
maximum value of the VCOM adjustment range and the initial VCOM voltage. Follow the steps below to calculate the
correct values for R1 and R2
Step 1: Choose the supply voltage, (VS)
Step 2: Set the nominal VCOM voltage. This voltage is the
VCOM voltage at which the unadjusted panel should be at
power-on. The default power-up DAC code is midscale.
Step 3: Choose the VCOM adjustment range. The adjustment range is the difference between the lowest and the
highest desired VCOM voltage. If the default power-up code
is not overwritten by software at the beginning of the adjustment cycle, the adjustment range is symmetrical
around the chosen nominal VCOM voltage.
Step 4: Calculate the resistors based on the following formulas or simply download the Microsoft Excel calculator
located in the product folder of BUF0190x available at
www.ti.com.
R1 +
250kW @ Adj_range
VCOM * 0.5 @ (Adj_range)
R2 +
V
V
S
COM
ǒ
)
1
500kW
Ǔ*
1
R
1
1
* 250kW
The BUF01900 can be used to drive small motors directly
because of the large output drive capability (> 100mA), as
illustrated in Figure 23.
VSD
@ R 2 ) 250kW @ ǒR 1 ) R 2Ǔ
15V
(2)
@ R 2 @ V S ) R 1 @ R 2 @ V S (Codeń1023)
R1
MOTOR DRIVE CIRCUIT
1
1
R
1
With R1 and R2 properly set, VBIAS or VCOM output voltage
can be calculated for any digital code with the following formula:
V COM +
Step 1: Supply Voltage is 10V.
Step 2: Nominal VCOM is determined to be 4V.
Step 3: The desired total adjustment range is 1V. In the
case of using the default power-up DAC code (midscale),
the adjustment range for the VCOM voltage will be from
3.5V to 4.5V.
Step 4: Calculation of R1 and R2
R1 = 71.4kΩ => choose closest 1% resistor (71.5kΩ)
R2 = 45.5kΩ => choose closest 1% resistor (45.3kΩ)
Step 5: Appropriate number of adjustment steps between
code 00h and code 3FFh is determined to be 32. This value
leads to a step size of 32 codes between adjustment
points, which translates into approximately 31mV voltage
difference between steps.
(1)
CALCULATING THE VCOM OUTPUT VOLTAGE
250kW
DESIGN EXAMPLE
10kΩ
10kΩ
VCOM
µC
BUF01900
M
(3)
CALCULATING THE ADJUSTMENT
RESOLUTION
Figure 23. Motor Drive Circuit
The resolution of the adjustment is a function of the step
size. The resolution can be calculated by simply dividing
the chosen adjustment range by the number of steps:
Resolution = Adj_range/steps (example: 32 steps between code 0h and code 3FFh)
15
"#$%&$$
"#$%&$%
www.ti.com
SBOS337A − OCTOBER 2006 − REVISED OCTOBER 2006
PROGRAMMABLE POWER SUPPLY
The BUF0190x integrated buffer amplifier can drive large
capacitive loads (see Typical Characteristics) and greater
than 100mA of output current, making it well-suited for programmable power supplies.
Note that the BUF01900 integrated buffer has an input
range that only extends to about 0.8V above GND; therefore, the programmable power supply is not able to output
voltages less than approximately 0.8V.
3.3V
10kΩ
15V
10kΩ
(1)
µC
Load
+
100µF
BUF01900
NOTE: (1) Optional −see Typical Characteristic curves
Figure 10 through Figure 14 for load regulation
performance.
Figure 24. Programmable Power Supply
16
QFN/DFN THERMALLY-ENHANCED
PACKAGE
The BUF0190x uses the 10-lead DFN package, a thin,
thermally-enhanced package designed to eliminate the
use of bulky heat sinks and slugs traditionally used in thermal packages. The DFN package can be easily mounted
using standard printed circuit board (PCB) assembly techniques. See QFN/SON PCB Attachment Application Note
(SLUA271) available at www.ti.com.
The thermal resistance junction to ambient (Rq JA) of the
DFN package depends on the PCB layout. Using thermal
vias and wide PCB traces improves thermal resistance.
The thermal pad must be soldered to the PCB. The thermal
pad on the bottom of the package should be connected to
GND.
Soldering the exposed thermal pad significantly improves
board-level reliability during temperature cycling, key
push, package shear, and similar board-level tests. Even
with applications that have low-power dissipation, the exposed pad must be soldered to the PCB to provide structural integrity and long-term reliability.
PACKAGE OPTION ADDENDUM
www.ti.com
26-Sep-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
BUF01900AIDRCR
ACTIVE
SON
DRC
10
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
BUF01900AIDRCRG4
ACTIVE
SON
DRC
10
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
BUF01900AIDRCT
ACTIVE
SON
DRC
10
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
BUF01900AIDRCTG4
ACTIVE
SON
DRC
10
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
BUF01900AIPW
ACTIVE
TSSOP
PW
8
150
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
BUF01900AIPWG4
ACTIVE
TSSOP
PW
8
150
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
BUF01900AIPWR
ACTIVE
TSSOP
PW
8
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
BUF01900AIPWRG4
ACTIVE
TSSOP
PW
8
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
BUF01901AIDRCR
ACTIVE
SON
DRC
10
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
BUF01901AIDRCRG4
ACTIVE
SON
DRC
10
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
BUF01901AIDRCT
ACTIVE
SON
DRC
10
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
BUF01901AIDRCTG4
ACTIVE
SON
DRC
10
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
BUF01901AIPW
ACTIVE
TSSOP
PW
8
150
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
BUF01901AIPWG4
ACTIVE
TSSOP
PW
8
150
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
BUF01901AIPWR
ACTIVE
TSSOP
PW
8
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
BUF01901AIPWRG4
ACTIVE
TSSOP
PW
8
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
26-Sep-2007
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
4-Oct-2007
TAPE AND REEL BOX INFORMATION
Device
Package Pins
Site
Reel
Diameter
(mm)
Reel
Width
(mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
BUF01900AIDRCR
DRC
10
SITE 41
330
12
3.3
3.3
1.1
8
12
Q2
BUF01900AIDRCT
DRC
10
SITE 41
180
12
3.3
3.3
1.1
8
12
Q2
BUF01900AIPWR
PW
8
SITE 41
330
12
7.0
3.6
1.6
8
12
Q1
BUF01901AIDRCR
DRC
10
SITE 41
330
12
3.3
3.3
1.1
8
12
Q2
BUF01901AIDRCT
DRC
10
SITE 41
180
12
3.3
3.3
1.1
8
12
Q2
BUF01901AIPWR
PW
8
SITE 41
330
12
7.0
3.6
1.6
8
12
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
4-Oct-2007
Device
Package
Pins
Site
Length (mm)
Width (mm)
Height (mm)
BUF01900AIDRCR
DRC
10
SITE 41
346.0
346.0
29.0
BUF01900AIDRCT
DRC
10
SITE 41
190.0
212.7
31.75
29.0
BUF01900AIPWR
PW
8
SITE 41
346.0
346.0
BUF01901AIDRCR
DRC
10
SITE 41
346.0
346.0
29.0
BUF01901AIDRCT
DRC
10
SITE 41
190.0
212.7
31.75
BUF01901AIPWR
PW
8
SITE 41
346.0
346.0
29.0
Pack Materials-Page 2
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
0,65
14
0,10 M
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
8
14
16
20
24
28
A MAX
3,10
5,10
5,10
6,60
7,90
9,80
A MIN
2,90
4,90
4,90
6,40
7,70
9,60
DIM
4040064/F 01/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties
may be subject to additional restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Telephony
www.ti.com/telephony
Low Power
Wireless
www.ti.com/lpw
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated