NKK EB2011G-CB Light touch miniature pushbutton Datasheet

Light Touch Miniature Pushbuttons
Series EB
Distinctive Characteristics
Power and logic level capabilities available to suit varying applications.
Bushing and snap-in mount versions available; snap-in models offer
many style and color choices to enhance front panel appearance.
Light touch actuation.
High torque bushing prevents rotation and separation from
metal frame during installation.
Stainless steel frame resists corrosion.
Case of heat resistant resin meets UL 94V-0 flammability
rating.
Higher insulating barriers protect against crossover in
double pole devices.
1,500V dielectric strength between contacts and case
is accomplished by clinching the frame away from the
terminals.
Epoxy sealed terminals prevent entry of solder flux and
other contaminants.
Actual Size
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
03-07
Light Touch Miniature Pushbuttons
Series EB
General Specifications
Electrical Capacity (Resistive Load)
Power Level (No code or P):
Logic Level (code G or PG):
3A @ 125V AC for silver contacts
0.4VA maximum @ 28V AC/DC maximum for gold contacts
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
Other Ratings
Contact Resistance:
Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Nominal Operating Force:
Travel:
10 milliohms maximum for silver; 20 milliohms maximum for gold
1,000 megohms minimum @ 500V DC
1,000V AC minimum between contacts for 1 minute minimum;
1,500V AC minimum between contacts and case for 1 minute minimum
100,000 operations minimum
25,000 operations minimum for silver;
50,000 operations minimum for gold
Single Pole: 2.35N for Momentary and 2.65N for Alternate Action
Double Pole: 2.94N for Momentary and 3.63N for Alternate Action
Momentary: Pretravel .047” (1.2mm); Overtravel .016” (0.4mm); Total Travel .063” (1.6mm)
Alternate: Pretravel .071” (1.8mm); Overtravel .016” (0.4mm); Total Travel .087” (2.2mm)
Materials & Finishes
Plunger:
Bushing:
Frame:
Case:
Movable Contacts:
Stationary Contacts:
Terminals:
Brass with chrome plating for Momentary; brass with nickel plating for Alternate
Brass with nickel plating
Stainless steel
Melamine phenolic resin (UL94V-0)
Copper with silver or gold plating
Silver with silver or gold plating
Copper with silver or gold plating
Environmental Data
Operating Temp Range:
Humidity:
Vibration:
Shock:
–10°C through +70°C (+14°F through +158°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range and returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Installation
Mounting Torque:
Cap Installation Force:
Soldering Time & Temp:
Cleaning:
1.47Nm (13.0 lb • in) for double nut; 0.68Nm (6.0 lb • in) for single nut
78.5N (17.65 lbf) maximum downward force on actuator
Wave Solder (Straight PC): See Profile B in Supplement section.
Manual Soldering: See Profile B in Supplement section.
These devices are not process sealed. Hand clean locally using alcohol based solution.
Standards & Certifications
Flammability Standards:
UL Recognized:
C-UL Recognized:
R
CSA Certified:
UL94V-0 case
All single and double pole models recognized at 3A @ 125V AC; UL File No. WOYR2.E44145;
add “/U” to end of part number to order UL mark on switch.
All single and double pole models recognized at 3A @ 125V AC; UL File No. WOYR8.E44145;
add “/C-UL” to end of part number to order C-UL mark on switch.
Single pole solder lug and PC models certified at 3A @ 125V AC; double pole PC models certified
at 3A @ 125V AC; CSA File No. 023535-0-000;
add “/C” to end of part number to order CSA mark on switch.
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
03-07
Light Touch Miniature Pushbuttons
Series EB
TYPICAL SWITCH ORDERING EXAMPLE
EB20
65
B
POLES & CIRCUITS
CAPS
11
SPDT
ON
(ON)
B
.315” (8.0mm) Dia.
65
SPDT
ON
ON
C
.394” (10.0mm) Dia.
61
DPDT
ON
(ON)
85
DPDT
ON
ON
( ) = Momentary
F
COLORS
CONTACTS, RATINGS, & TERMINALS
Silver Contacts; Solder Lug Terminals;
3A @ 125V AC
A
Black
B
White
G
Gold Contacts; Solder Lug Terminals
0.4VA max @ 28V AC/DC max
C
Red
Silver Contacts; Straight PC Terminals;
3A @ 125V AC
E
Yellow
P
F
Green
G
Blue
H
Gray
No
Code
PG
Gold Contacts; Straight PC Terminals
0.4VA max @ 28V AC/DC max
IMPORTANT:
Switches are supplied without UL, C-UL
& CSA markings unless specified. Specific models & ratings noted on General
Specifications page.
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
EB2065-BF
Green .315” (8.0mm)
Diameter Cap
SPDT
ON-ON Circuit
Silver Contacts & Solder Lug
Terminals with 3-Amp Rating
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
03-07
Series EB
Light Touch Miniature Pushbuttons
POLES & CIRCUITS
Plunger Position
( ) = Momentary
Normal
Down
Connected Terminals
Normal
Keyway
Throw & Switch Schematics
Down
Note: Terminal numbers are
not actually on the switch.
Keyway
Pole
Model
SP
EB2011
EB2065
ON
ON
(ON)
ON
2-3
2-1
SPDT
DP
EB2061
EB2085
ON
ON
(ON)
ON
2-3 5-6
2-1 5-4
DPDT
2 (COM)
3
2
1
5
(COM)
3
1
6
4
CONTACT MATERIALS, RATINGS, & TERMINALS
No
Code
Solder Lug
Silver Contacts
Power Level
3A @ 125V AC
G
Solder Lug
Gold Contacts
Logic Level
0.4VA max @ 28V AC/DC max
Complete explanation of operating range in Supplement section.
(2.0)
.079
Epoxy Seal
(2.0)
.079
(4.0)
(1.1) .157
.043
Thk (0.7) (0.5) Com
.028 .020
P
Straight PC
Silver Contacts
Power Level
PG
Straight PC
Gold Contacts
Logic Level
3A @ 125V AC
0.4VA max @ 28V AC/DC max
Complete explanation of operating range in Supplement section.
PCB Footprints
Single Pole
Epoxy Seal
(6.4)
(4.3) .252
.169
(1.2)
.047
Thk (0.7) (0.5) Com
.028 .020
Double Pole
(4.7)
.185
3
2
(3.9) Typ
.154
1
(1.8) Dia Typ
.071
3
6
2
5
1
4
(3.9) Typ
.154
(1.8) Dia Typ
.071
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
03-07
Light Touch Miniature Pushbuttons
Series EB
CAPS & COLORS
B
AT443
.315” (8.0mm) Diameter Snap-on Cap
C
Cap Colors
Available:
A
B
AT442
.394” (10.0mm) Diameter Snap-on Cap
Cap Colors
Available:
F
Black
White
G
C
Red
H
E
Yellow
A
Green
(7.6)
.299
Blue
(8.0) Dia
.315
Gray
Cap Material: Polycarbonate
Black
F
Green
B
White
G
Blue
C
Red
H
Gray
E
Yellow
Finish: Glossy
(8.0)
.315
(10.0) Dia
.394
Cap Material: Polycarbonate
Finish: Glossy
Plunger Extension
Due to a difference in plunger lengths on the momentary and alternate action models, cap distance from top of bushing varies.
(2.3) Dia
.091
(2.3) Dia
.091
(3.0) Dia
.118
(8.0)
.315
(3.3) Dia
.130
(9.3)
.366
(1.2)
.047
(1.4)
.055
Momentary
Plunger Length
(3.0) Dia
.118
(2.5)
.098
(2.7)
.106
Momentary
Cap Location
Alternate
Plunger Length
Alternate
Cap Location
TYPICAL SWITCH DIMENSIONS
Solder Lug
Single Pole
M6 P0.75
Keyway
(8.0) Dia
.315
(11.0)
.433
3
COM
2
(0.5)
.020
(1.4)
.055
(7.6)
.299
(7.0)
.276
(1.1) x (2.0) Typ
.043 x .079
(0.7) Typ
.028
(3.9) Typ
.154
(6.8)
(4.5)
.268
.177
(8.5)
(18.0)
.335
.709
For Momentary Devices
1
(4.0) Typ
.157
(2.0) Typ
.079
EB2011-BA
Solder Lug
Double Pole
Keyway
M6 P0.75
(11.0)
.433
(8.0) Dia
.315
(11.7)
.461
(1.1) x (2.0) Typ
.043 x .079
(0.7) Typ
.028
(3.9) Typ
.154
(0.5)
.020
(1.4)
.055
(7.6)
.299
(6.8)
(4.5)
.268
.177
(8.5)
(18.0)
.335
.709
For Momentary Devices
COM
6
3
5
2
4
1
(4.0) Typ
.157
(4.7)
.185
(2.0) Typ
.079
EB2061-BA
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
03-07
Light Touch Miniature Pushbuttons
Series EB
HARDWARE
Installation/Assembly
Standard Hardware
2 AT513M Metric Hexagon Nuts
1 AT509 Internal Tooth Lockwasher
Face Nut
Lockwasher
Optional Hardware
AT513M
Metric Hexagon Nut
AT509
Lockwasher
AT507M
Metric Locking Ring
Material:
Brass with
Nickel Plating
Material:
Steel with
Zinc/Chromate
Material:
Steel with
Zinc/Chromate
Locking Ring
(Optional)
Lock Nut
(6.0) Dia
.236
M6 P0.75
Optional Hardware:
AT507M Metric Locking Ring
(8.0)
.315
Note: Cap must be snapped on
after the switch is mounted
into the panel.
(6.4) Dia (10.2) Dia
.252
.402
(12.0) Dia
.472
(2.0)
.079
(5.5)
.217
(0.5)
.020
(1.5)
.059
(9.0)
.354
(1.7)
.067
(0.8)
.031
Panel Thicknesses & Panel Cutouts
Metric Bushing
(8.0) Dia
.315
With
Standard Hardware
With Standard Hardware
& Optional Locking Ring
Without
Bottom Hex Nut
Maximum Effective
Panel Thickness:
.118” (3.0mm)
Maximum Effective
Panel Thickness:
.055” (1.4mm)
Maximum Effective
Panel Thickness:
.185” (4.7mm)
M6 P0.75
(0.8)
.031
(2.5)
.098
(8.5)
.335
(5.6)
.220
(1.7)
.067
(6.35) Dia
.250
(0.6)
.024
(6.35) Dia
.250
(6.5) Dia
.256
(2.2) Dia
.087
(6.5)
.256
See Accessories & Hardware section for optional Conical Nuts:
AT512M used with cap AT443 and AT512CM used with cap AT442.
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
03-07
Similar pages