HFBR-0600Z Series SERCOS Fiber Optic Transmitters and Receivers Data Sheet SERCOS Features SERCOS is a Serial Realtime Communication System, a standard digital interface for communication between controls and drives for numerically controlled machines. The SERCOS interface specification was written by a joint working group of the VDW (German Machine Tool Builders Association) and ZVEI (German Electrical and Electronic Manufacturer’s Association) to allow data exchange between NC controls and drives via fiber optic rings, with isolation and noise immunity. The HFBR-0600Z family of fiber optic transmitters and receivers comply to the SERCOS specifications for transmitter and receiver optical characteristics and connector style (SMA). Fully compliant to SERCOS optical specifications Description Tempest-secure data processing equipment The HFBR-0600Z components are capable of operation at symbol rates from DC to over 2 MBd and distances from 0 to over 20 metres. The HFBR-1602Z and HFBR-1604Z transmitters contain a 655 nm AlGaAs emitter capable of efficiently launching optical power into 1000 mm plastic optical fiber. The optical output is specified at the end of 0.5 m of plastic optical fiber. Optimized for 1 mm plastic optical fiber Compatible with SMA connectors Auto-insertable and wave solderable Data transmission at symbol rates from DC to over 2 MBd for distances from 0 to over 20 metres Applications Industrial control data links Reduction of lightning and voltage transient susceptibility Isolation in test and measurement instruments Robotics communication The HFBR-1604Z is a selected version of the HFBR-1602, with power specified to meet the SERCOS high attenuation specifications. The HFBR-2602Z receiver incorporates an integrated photo IC containing a photodetector and DC amplifier driving an open-collector Schottky output transistor. The HFBR-2602Z is designed for direct interfacing to popular logic families. The absence of an internal pullup resistor allows the open-collector output to be used with logic families such as CMOS requiring voltage excursions higher than VCC. The HFBR-2602Z has a dynamic range of 15 dB. CAUTION: The small junction sizes inherent to the design of this component increase the component's susceptibility to damage from electrostatic discharge (ESD). It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. HFBR-160XZ Transmitters HFBR-0600Z SMA Series Mechanical Dimensions Pin Function 1* 2 3 4* 5* 6 7** 8* N.C. ANODE N.C. N.C. N.C. N.C. CATHODE N.C. Pin Function 1* 2 3 4* 5* 6 7 8* N.C. VCC (5 V) COMMON N.C. N.C. DATA COMMON N.C. HFBR-2602Z Receiver * Pins 1, 4, 5, and 8 are isolated from the internal circuitry, but electrically connected to one another. ** Transmitter Pin 7 may be left unconnected if necessary. In the receiver, both the opencollector “Data” output Pin 6 and VCC Pin 2 are referenced to “Common” Pin 3 and 7. It is essential that a bypass capacitor (0.1 F ceramic) be connected from Pin 2 (VCC) to Pin 3 (circuit common) of the receiver. 2 SMA is an industry standard fiber optic connector, available from many fiber optic connector suppliers. HFBR-4401Z is a kit consisting of 100 nuts and 100 washers for panel mounting the HFBR-0600Z components. HFBR-1602Z/1604Z Transmitters Absolute Maximum Ratings Parameter Symbol Min. Max. Units Storage Temperature TS -55 85 °C Operating Temperature TA -40 85 °C Temp. 260 °C Note 1 Time 10 s Note 1 IFPK 120 mA Forward Input Current Average IFavg 60 mA Reverse Input Voltage VBR -5 V Lead Soldering Cycle Forward Input Current Peak Reference Electrical/Optical Characteristics 0 to 55° C, unless otherwise stated. Parameter Symbol Min. Typ.[2] Max. Unit Condition Forward Voltage VF 1.5 1.9 2.2 V IF = 35 mA Forward Voltage Temp. Coefficient VF/T -1.2 mV/°C IF = 35 mA Reverse Input Voltage VBR -5.0 -18 V IR = 100 A Peak Emission Wavelength P 640 655 675 Full Width Half Maximum FWHM 20 30 nm 25° C Diode Capacitance CT 30 pF VF = 0 f = 1 MHz Optical Power Temp. Coefficient PT/T -0.01 dBm/°C IF = 35 mA Thermal Resistance JA 330 °C/W Peak Optical Output Power of HFBR-1602Z PT1602 -10.5 -5.5 dBm IF = 35 mA Notes 5, 6,11 Peak Optical Output Power of HFBR-1604Z PT1604 -7.5 -10.5 -3.5 -5.5 dBm dBm IF = 60 mA IF = 35 mA Notes 5, 6,11 Rise Time (10% to 90%) tr 57 50 ns ns IF = 60 mA IF = 35 mA Fall Time (90% to 10%) tf 40 27 ns ns IF = 60 mA IF = 35 mA 3 Reference nm Notes 3, 4 HFBR-2602Z Receiver Absolute Maximum Ratings Parameter Symbol Min. Max. Units Storage Temperature TS -55 85 °C Operating Temperature TA -40 85 °C Temp. 260 °C Note 1 Time 10 s Note 1 7.0 V 25 mA 18.0 V mW Lead Soldering Cycle Supply Voltage -0.5 Vcc Output Current IO Output Voltage VO Output Collector Power Dissipation PO AVG 40 Fan Out (TTL) N 5 -0.5 Reference Note 8 Electrical/Optical Characteristics 0 to 55° C; Fiber core diameter ≤ 1.0 mm, fiber N.A. ≤ 0.5, 4.75 V ≤ VCC ≤ 5.25 V Typ.[2] Max. Unit Condition IOH 5 250 A VOH = 18 V PR < -31.2 dBm Low Level Output Voltage VOL 0.4 0.5 V IOL = 8 mA PR > -20.0 dBm High Level Supply Current ICCH 3.5 6.3 mA VCC = 5.25 V PR < -31.2 dBm Low Level Supply Current ICCL 6.2 10 mA VCC = 5.25 V PR > -20.0 dBm Parameter Symbol High Level Output Current Min. Reference Dynamic Characteristics 0 to 55° C unless otherwise specified; 4.75 V ≤ VCC ≤ 5.25 V; BER ≤ 10-9 Parameter Symbol Peak Input Power Level Logic HIGH PRH Peak Input Power Level Logic LOW PRL Propagation Delay LOW to HIGH tPLH Propagation Delay HIGH to LOW Pulse Width Distortion, tPLH - tPHL Min. Typ.[2] Max. Unit Condition Reference -31.2 dBm P = 655 nm Note 7 -5.0 dBm IOL = 8 mA Note 7 60 ns PR = -20 dBm 2 MBd Note 8, 9 tPHL 110 ns PR = -20 dBm 2 MBd Note 8, 9 PWD 50 -50 ns ns PR = -5 dBm PR = -20 dBm Note 10 Figure 6 -20.0 Notes: 1. 2.0 mm from where leads enter case. 2. Typical data at TA = +25° C. 3. Thermal resistance is measured with the transmitter coupled to a connector assembly and fiber, and mounted on a printed circuit board. 4. Pins 2, 6, and 7 are welded to the cathode header connection to minimize the thermal resistance from junction to ambient. To further reduce the thermal resistance, the cathode trace should be made as large as is consistent with good RF circuit design. 5. PT is measured with a large area detector at the end of 0.5 metre of plastic optical fiber with 1 mm diameter and numerical aperture of 0.5. 6. When changing W to dBm, the optical power is referenced to 1 mW (1000 W). Optical Power P(dBm) = 10 log [P (W)/1000 W]. 7. Measured at the end of 1mm plastic fiber optic cable with a large area detector. 8. 8 mA load (5 x 1.6 mA), RL = 560 . 9. Propagation delay through the system is the result of several sequentially occurring phenomena. Consequently it is a combination of data-ratelimiting effects and of transmission-time effects. Because of this, the data-rate limit of the system must be described in terms of time differentials between delays imposed on falling and rising edges. As the cable length is increased, the propagation delays increase. Data-rate, as limited by pulse width distortion, is not affected by increasing cable length if the optical power level at the receiver is maintained. 10. Pulse width distortion is the difference between the delay of the rising and falling edges. 11. Both HFBR-1602Z and HFBR-1604Z meet the SERCOS "low attenuation" specifications when operated at 35 mA; only HFBR-1604Z meets the SERCOS "high attenuation" limits when operated at 60 mA. 4 Figure 1. Forward voltage and current characteristics. Figure 2. Typical transmitter output vs. forward current. Figure 3. Transmitter spectrum normalized to the peak at 25° C. Figure 4. Typical propagation delay through system with 0.5 metre of cable. Figure 5. Typical HFBR-160XZ/2602Z link pulsewidth distortion vs. optical power. 5 Figure 6. System propagation delay test circuit and waveform timing definitions. For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2012 Avago Technologies. All rights reserved. Obsoletes 5989-4798EN AV02-3638EN - June 19, 2012