ATMEL ATMEGA164PA High-performance, low-power avr Datasheet

ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P
8-bit Atmel Microcontroller with 16/32/64/128K Bytes
In-System Programmable Flash
DATASHEET SUMMARY
Features
z
High-performance, low-power 8-bit Atmel® AVR® Microcontroller
z
Advanced RISC architecture
̶ 131 powerful Instructions – most single-clock cycle execution
̶ 32 × 8 general purpose working registers
̶ Fully static operation
̶ Up to 20MIPS throughput at 20MHz
̶ On-chip 2-cycle multiplier
z
High endurance non-volatile memory segments
̶ 16/32/64/128KBytes of In-System Self-programmable Flash program memory
̶ 512/1K/2K/4KBytes EEPROM
̶ 1/2/4/16KBytes Internal SRAM
̶ Write/Erase Cycles: 10,000 Flash/ 100,000 EEPROM
̶ Data retention: 20 years at 85°C/ 100 years at 25°C(1)
̶ Optional Boot Code Section with Independent Lock Bits
z In-System Programming by On-chip Boot Program
z True Read-While-Write Operation
̶ Programming Lock for Software Security
z
Atmel QTouch® library support
̶ Capacitive touch buttons, sliders and wheels
̶ QTouch and QMatrix acquisition
̶ Up to 64 sense channels
z
JTAG (IEEE std. 1149.1 Compliant) Interface
̶ Boundary-scan Capabilities According to the JTAG Standard
̶ Extensive On-chip Debug Support
̶ Programming of Flash, EEPROM, Fuses, and Lock Bits through the JTAG
Interface
z
Peripheral Features
̶ Two 8-bit Timer/Counters with Separate Prescalers and Compare Modes
̶ One/two 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and
Capture Mode
̶ Real Time Counter with Separate Oscillator
̶ Six PWM Channels
̶ 8-channel, 10-bit ADC
z Differential mode with selectable gain at 1×, 10× or 200×
̶ Byte-oriented Two-wire Serial Interface
̶ Two Programmable Serial USART
̶ Master/Slave SPI Serial Interface
Atmel-8272FS-AVR--07/2014
̶
̶
̶
Programmable Watchdog Timer with Separate On-chip Oscillator
On-chip Analog Comparator
Interrupt and Wake-up on Pin Change
z
Special Microcontroller Features
̶ Power-on Reset and Programmable Brown-out Detection
̶ Internal Calibrated RC Oscillator
̶ External and Internal Interrupt Sources
̶ Six Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, Standby and Extended Standby
z
I/O and Packages
̶ 32 Programmable I/O Lines
̶ 40-pin PDIP, 44-lead TQFP, 44-pad VQFN/QFN/MLF
̶ 44-pad DRQFN
– 49-ball VFBGA
Note:
z
Operating Voltages
̶ 1.8 - 5.5V
z
Speed Grades
̶ 0 - 4MHz @ 1.8 - 5.5V
̶ 0 - 10MHz @ 2.7 - 5.5V
̶ 0 - 20MHz @ 4.5 - 5.5V
z
Power Consumption at 1MHz, 1.8V, 25°C
̶ Active: 0.4mA
̶ Power-down Mode: 0.1µA
̶ Power-save Mode: 0.6µA (Including 32kHz RTC)
1. See ”Data retention” on page 9 for details.
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
2
1.
Pin configurations
1.1
Pinout - PDIP/TQFP/VQFN/QFN/MLF for
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P
Figure 1-1.
Pinout.
(PCINT8/XCK0/T0) PB0
(PCINT9/CLKO/T1) PB1
(PCINT10/INT2/AIN0) PB2
(PCINT11/OC0A/AIN1) PB3
(PCINT12/OC0B/SS) PB4
(PCINT13/ICP3/MOSI) PB5
(PCINT14/OC3A/MISO) PB6
(PCINT15/OC3B/SCK) PB7
RESET
VCC
GND
XTAL2
XTAL1
(PCINT24/RXD0/T3*) PD0
(PCINT25/TXD0) PD1
(PCINT26/RXD1/INT0) PD2
(PCINT27/TXD1/INT1) PD3
(PCINT28/XCK1/OC1B) PD4
(PCINT29/OC1A) PD5
(PCINT30/OC2B/ICP) PD6
PA0 (ADC0/PCINT0)
PA1 (ADC1/PCINT1)
PA2 (ADC2/PCINT2)
PA3 (ADC3/PCINT3)
PA4 (ADC4/PCINT4)
PA5 (ADC5/PCINT5)
PA6 (ADC6/PCINT6)
PA7 (ADC7/PCINT7)
AREF
GND
AVCC
PC7 (TOSC2/PCINT23)
PC6 (TOSC1/PCINT22)
PC5 (TDI/PCINT21)
PC4 (TDO/PCINT20)
PC3 (TMS/PCINT19)
PC2 (TCK/PCINT18)
PC1 (SDA/PCINT17)
PC0 (SCL/PCINT16)
PD7 (OC2A/PCINT31)
PB4 (SS/OC0B/PCINT12)
PB3 (AIN1/OC0A/PCINT11)
PB2 (AIN0/INT2/PCINT10)
PB1 (T1/CLKO/PCINT9)
PB0 (XCK0/T0/PCINT8)
GND
VCC
PA0 (ADC0/PCINT0)
PA1 (ADC1/PCINT1)
PA2 (ADC2/PCINT2)
PA3 (ADC3/PCINT3)
TQFP/QFN/MLF
(PCINT13/ICP3/MOSI) PB5
(PCINT14/OC3A/MISO) PB6
(PCINT15/OC3B/SCK) PB7
RESET
VCC
GND
XTAL2
XTAL1
(PCINT24/RXD0/T3*) PD0
(PCINT25/TXD0) PD1
(PCINT26/RXD1/INT0) PD2
PD3
PD4
PD5
PD6
PD7
VCC
GND
(PCINT16/SCL) PC0
(PCINT17/SDA) PC1
(PCINT18/TCK) PC2
(PCINT19/TMS) PC3
(PCINT27/TXD1/INT1)
(PCINT28/XCK1/OC1B)
(PCINT29/OC1A)
(PCINT30/OC2B/ICP)
(PCINT31/OC2A)
*T3 is only available for ATmega1284/1284P
PA4 (ADC4/PCINT4)
PA5 (ADC5/PCINT5)
PA6 (ADC6/PCINT6)
PA7 (ADC7/PCINT7)
AREF
GND
AVCC
PC7 (TOSC2/PCINT23)
PC6 (TOSC1/PCINT22)
PC5 (TDI/PCINT21)
PC4 (TDO/PCINT20)
Note:
The large center pad underneath the VQFN/QFN/MLF package should be soldered to ground on the board to
ensure good mechanical stability.
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
3
Pinout - DRQFN for Atmel ATmega164A/164PA/324A/324PA
Figure 1-2.
DRQFN - pinout.
Top view
Bottom view
A18
B1
B15
A17
B2
B14
B3
B4
A2
A3
A4
A5
B5
A18
A1
B15
A17
B1
B14
B2
A16
B13
A16
B13
B3
A15
B12
A15
A2
A3
A4
B4
A14
B12
A14
B11
A13
B11
A13
B5
A5
A6
A12
B10
A11
B9
A10
B8
A9
B7
A8
B6
A7
B8
A10
B9
A11
B10
A12
B7
A9
A8
B6
A6
Table 1-1.
A24
B20
A23
B19
A22
B18
A21
B17
A20
B16
A19
A19
B16
A20
B17
A21
B18
A22
B19
A23
B20
A24
A1
A7
1.2
DRQFN - pinout.
A1
PB5
A7
PD3
A13
PC4
A19
PA3
B1
PB6
B6
PD4
B11
PC5
B16
PA2
A2
PB7
A8
PD5
A14
PC6
A20
PA1
B2
RESET
B7
PD6
B12
PC7
B17
PA0
A3
VCC
A9
PD7
A15
AVCC
A21
VCC
B3
GND
B8
VCC
B13
GND
B18
GND
A4
XTAL2
A10
GND
A16
AREF
A22
PB0
B4
XTAL1
B9
PC0
B14
PA7
B19
PB1
A5
PD0
A11
PC1
A17
PA6
A23
PB2
B5
PD1
B10
PC2
B15
PA5
B20
PB3
A6
PD2
A12
PC3
A18
PA4
A24
PB4
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
4
1.3
Pinout - VFBGA for Atmel ATmega164A/164PA/324A/324PA
Figure 1-3.
VFBGA - pinout.
Top view
1
3
4
5
6
7
7
6
5
4
3
2
1
A
A
B
B
C
C
D
D
E
E
F
F
G
G
Table 1-2.
2.
2
Bottom view
BGA - pinout.
1
2
3
4
5
6
7
A
GND
PB4
PB2
GND
VCC
PA2
GND
B
PB6
PB5
PB3
PB0
PA0
PA3
PA5
C
VCC
RESET
PB7
PB1
PA1
PA6
AREF
D
GND
XTAL2
PD0
GND
PA4
PA7
GND
E
XTAL1
PD1
PD5
PD7
PC5
PC7
AVCC
F
PD2
PD3
PD6
PC0
PC2
PC4
PC6
G
GND
PD4
VCC
GND
PC1
PC3
GND
Overview
The Atmel ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P is a low-power CMOS 8-bit
microcontroller based on the AVR enhanced RISC architecture. By executing powerful instructions in a single
clock cycle, the ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P achieves throughputs
approaching 1 MIPS per MHz allowing the system designer to optimize power consumption versus processing
speed.
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
5
2.1
Block diagram
Figure 2-1.
Block diagram.
PA7..0
PB7..0
VCC
RESET
GND
Power
Supervision
POR / BOD &
RESET
PORT A (8)
PORT B (8)
Watchdog
Timer
Analog
Comparator
A/D
Converter
Watchdog
Oscillator
USART 0
XTAL1
Oscillator
Circuits /
Clock
Generation
EEPROM
Internal
Bandgap reference
XTAL2
SPI
8bit T/C 0
CPU
16bit T/C 1
16bit T/C 1
JTAG/OCD
8bit T/C 2
TWI
FLASH
SRAM
PORT C (8)
TOSC2/PC7
TOSC1/PC6
16bit T/C 3*
USART 1
PORT D (8)
PD7..0
PC5..0
* Only available in ATmega1284/1284P
The AVR core combines a rich instruction set with 32 general purpose working registers. All the 32 registers are
directly connected to the Arithmetic Logic Unit (ALU), allowing two independent registers to be accessed in one
single instruction executed in one clock cycle. The resulting architecture is more code efficient while achieving
throughputs up to ten times faster than conventional CISC microcontrollers.
The Atmel ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P provide the following features:
16/32/64/128Kbytes of In-System Programmable Flash with Read-While-Write capabilities, 512/1K/2K/4Kbytes
EEPROM, 1/2/4/16Kbytes SRAM, 32 general purpose I/O lines, 32 general purpose working registers, Real
Time Counter (RTC), three (four for ATmega1284/1284P) flexible Timer/Counters with compare modes and
PWM, 2 USARTs, a byte oriented two-wire Serial Interface, a 8-channel, 10-bit ADC with optional differential
input stage with programmable gain, programmable Watchdog Timer with Internal Oscillator, an SPI serial port,
IEEE std. 1149.1 compliant JTAG test interface, also used for accessing the On-chip Debug system and
programming and six software selectable power saving modes. The Idle mode stops the CPU while allowing the
SRAM, Timer/Counters, SPI port, and interrupt system to continue functioning. The Power-down mode saves
the register contents but freezes the Oscillator, disabling all other chip functions until the next interrupt or
Hardware Reset. In Power-save mode, the asynchronous timer continues to run, allowing the user to maintain a
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
6
timer base while the rest of the device is sleeping. The ADC Noise Reduction mode stops the CPU and all I/O
modules except Asynchronous Timer and ADC, to minimize switching noise during ADC conversions. In
Standby mode, the Crystal/Resonator Oscillator is running while the rest of the device is sleeping. This allows
very fast start-up combined with low power consumption. In Extended Standby mode, both the main Oscillator
and the Asynchronous Timer continue to run.
Atmel offers the QTouch® library for embedding capacitive touch buttons, sliders and wheels functionality into
AVR microcontrollers. The patented charge-transfer signal acquisition offers robust sensing and includes fully
debounced reporting of touch keys and includes Adjacent Key Suppression® (AKS™) technology for
unambiguous detection of key events. The easy-to-use QTouch Suite toolchain allows you to explore, develop
and debug your own touch applications.
The device is manufactured using Atmel’s high-density nonvolatile memory technology. The On-chip ISP Flash
allows the program memory to be reprogrammed in-system through an SPI serial interface, by a conventional
nonvolatile memory programmer, or by an On-chip Boot program running on the AVR core. The boot program
can use any interface to download the application program in the application Flash memory. Software in the
Boot Flash section will continue to run while the Application Flash section is updated, providing true ReadWhile-Write operation. By combining an 8-bit RISC CPU with In-System Self-Programmable Flash on a
monolithic chip, the Atmel ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P is a powerful
microcontroller that provides a highly flexible and cost effective solution to many embedded control applications.
The ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P is supported with a full suite of program and
system development tools including: C compilers, macro assemblers, program debugger/simulators, in-circuit
emulators, and evaluation kits.
2.2
Comparison between ATmega164A, ATmega164PA, ATmega324A, ATmega324PA,
ATmega644A, ATmega644PA, ATmega1284 and ATmega1284P
Table 2-1.
Differences between ATmega164A, ATmega164PA, ATmega324A, ATmega324PA, ATmega644A,
ATmega644PA, ATmega1284 and ATmega1284P.
Device
Flash
EEPROM
RAM
ATmega164A
16K
512
1K
ATmega164PA
16K
512
1K
ATmega324A
32K
1K
2K
ATmega324PA
32K
1K
2K
ATmega644A
64K
2K
4K
ATmega644PA
64K
2K
4K
ATmega1284
128K
4K
16K
ATmega1284P
128K
4K
16K
2.3
Pin Descriptions11
2.3.1
VC
Units
bytes
Digital supply voltage.
2.3.2
GND
Ground.
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
7
2.3.3
Port A (PA7:PA0)
Port A serves as analog inputs to the Analog-to-digital Converter.
Port A also serves as an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The
Port A output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs,
Port A pins that are externally pulled low will source current if the pull-up resistors are activated. The Port A pins
are tri-stated when a reset condition becomes active, even if the clock is not running.
Port A also serves the functions of various special features of the Atmel
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P as listed on page 79.
2.3.4
Port B (PB7:PB0)
Port B is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port B output
buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port B pins
that are externally pulled low will source current if the pull-up resistors are activated. The Port B pins are tristated when a reset condition becomes active, even if the clock is not running.
Port B also serves the functions of various special features of the
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P as listed on page 80.
2.3.5
Port C (PC7:PC0)
Port C is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port C output
buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port C pins
that are externally pulled low will source current if the pull-up resistors are activated. The Port C pins are tristated when a reset condition becomes active, even if the clock is not running.
Port C also serves the functions of the JTAG interface, along with special features of the Atmel
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P as listed on page 83.
2.3.6
Port D (PD7:PD0)
Port D is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port D output
buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port D pins
that are externally pulled low will source current if the pull-up resistors are activated. The Port D pins are tristated when a reset condition becomes active, even if the clock is not running.
Port D also serves the functions of various special features of the
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P as listed on page 86.
2.3.7
RESET
Reset input. A low level on this pin for longer than the minimum pulse length will generate a reset, even if the
clock is not running. The minimum pulse length is given in ”” on page 325. Shorter pulses are not guaranteed to
generate a reset.
2.3.8
XTAL1
Input to the inverting Oscillator amplifier and input to the internal clock operating circuit.
2.3.9
XTAL2
Output from the inverting Oscillator amplifier.
2.3.10 AVCC
AVCC is the supply voltage pin for Port A and the Analog-to-digital Converter. It should be externally connected
to VCC, even if the ADC is not used. If the ADC is used, it should be connected to VCC through a low-pass filter.
2.3.11 AREF
This is the analog reference pin for the Analog-to-digital Converter.
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
8
3.
Resources
A comprehensive set of development tools, application notes and datasheets are available for download on
http://www.atmel.com/avr.
4.
About code examples
This documentation contains simple code examples that briefly show how to use various parts of the device. Be
aware that not all C compiler vendors include bit definitions in the header files and interrupt handling in C is
compiler dependent. Please confirm with the C compiler documentation for more details.
The code examples assume that the part specific header file is included before compilation. For I/O registers
located in extended I/O map, "IN", "OUT", "SBIS", "SBIC", "CBI", and "SBI" instructions must be replaced with
instructions that allow access to extended I/O. Typically "LDS" and "STS" combined with "SBRS", "SBRC",
"SBR", and "CBR".
Note:
5.
1.
Data retention
Reliability Qualification results show that the projected data retention failure rate is much less than 1 PPM over
20 years at 85°C or 100 years at 25°C.
6. Capacitive touch sensing
The Atmel QTouch Library provides a simple to use solution to realize touch sensitive interfaces on most Atmel
AVR microcontrollers. The QTouch Library includes support for the QTouch and QMatrix acquisition methods.
Touch sensing can be added to any application by linking the appropriate Atmel QTouch Library for the AVR
Microcontroller. This is done by using a simple set of APIs to define the touch channels and sensors, and then
calling the touch sensing API’s to retrieve the channel information and determine the touch sensor states.
The QTouch Library is FREE and downloadable from the Atmel website at the following location:
www.atmel.com/qtouchlibrary. For implementation details and other information, refer to the Atmel QTouch
Library User Guide - also available for download from the Atmel website.
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
9
7.
Address
Register summary
Bit 7
Bit 6
Bit 5
Bit 4
(0xFF)
Reserved
Name
-
-
-
-
Bit 3
Bit 2
Bit 1
Bit 0
-
-
-
(0xFE)
Reserved
-
-
-
-
-
-
-
-
(0xFD)
Reserved
-
-
-
-
-
-
-
-
(0xFC)
Reserved
-
-
-
-
-
-
-
-
(0xFB)
Reserved
-
-
-
-
-
-
-
(0xFA)
Reserved
-
-
-
-
-
-
-
(0xF9)
Reserved
-
-
-
-
-
-
-
(0xF8)
Reserved
-
-
-
-
-
-
-
-
(0xF7)
Reserved
-
-
-
-
-
-
-
-
(0xF6)
Reserved
-
-
-
-
-
-
-
-
(0xF5)
Reserved
-
-
-
-
-
-
-
(0xF4)
Reserved
-
-
-
-
-
-
-
-
(0xF3)
Reserved
-
-
-
-
-
-
-
-
(0xF2)
Reserved
-
-
-
-
-
-
-
-
(0xF1)
Reserved
-
-
-
-
-
-
-
(0xF0)
Reserved
-
-
-
-
-
-
-
(0xEF)
Reserved
-
-
-
-
-
-
-
(0xEE)
Reserved
-
-
-
-
-
-
-
-
(0xED)
Reserved
-
-
-
-
-
-
-
-
(0xEC)
Reserved
-
-
-
-
-
-
-
-
(0xEB)
Reserved
-
-
-
-
-
-
-
(0xEA)
Reserved
-
-
-
-
-
-
-
-
(0xE9)
Reserved
-
-
-
-
-
-
-
-
(0xE8)
Reserved
-
-
-
-
-
-
-
-
(0xE7)
Reserved
-
-
-
-
-
-
-
(0xE6)
Reserved
-
-
-
-
-
-
-
-
(0xE5)
Reserved
-
-
-
-
-
-
-
-
(0xE4)
Reserved
-
-
-
-
-
-
-
-
(0xE3)
Reserved
-
-
-
-
-
-
-
(0xE2)
Reserved
-
-
-
-
-
-
-
(0xE1)
Reserved
-
-
-
-
-
-
-
(0xE0)
Reserved
-
-
-
-
-
-
-
(0xDF)
Reserved
-
-
-
-
-
-
-
-
(0xDE)
Reserved
-
-
-
-
-
-
-
-
(0xDD)
Reserved
-
-
-
-
-
-
-
-
(0xDC)
Reserved
-
-
-
-
-
-
-
(0xDB)
Reserved
-
-
-
-
-
-
-
-
(0xDA)
Reserved
-
-
-
-
-
-
-
-
(0xD9)
Reserved
-
-
-
-
-
-
-
-
(0xD8)
Reserved
-
-
-
-
-
-
-
-
(0xD7)
Reserved
-
-
-
-
-
-
-
-
(0xD6)
Reserved
-
-
-
-
-
-
-
-
(0xD5)
Reserved
-
-
-
-
-
-
-
-
(0xD4)
Reserved
-
-
-
-
-
-
-
-
(0xD3)
Reserved
-
-
-
-
-
-
-
-
(0xD2)
Reserved
-
-
-
-
-
-
-
-
(0xD1)
Reserved
-
-
-
-
-
-
-
-
(0xD0)
Reserved
-
-
-
-
-
-
-
-
(0xCF)
Reserved
-
-
-
-
-
-
-
-
(0xCE)
UDR1
(0xCD)
UBRR1H
(0xCC)
UBRR1L
(0xCB)
-
-
-
USART1 I/O Data Register
-
-
-
Reserved
-
-
-
(0xCA)
UCSR1C
UMSEL11
UMSEL10
(0xC9)
UCSR1B
RXCIE1
TXCIE1
(0xC8)
UCSR1A
RXC1
TXC1
(0xC7)
Reserved
-
(0xC6)
UDR0
(0xC5)
UBRR0H
(0xC4)
UBRR0L
(0xC3)
-
Page
185
USART1 Baud Rate Register High Byte
189/202
USART1 Baud Rate Register Low Byte
189/202
-
-
-
-
-
UPM11
UPM10
USBS1
UCSZ11/UDORD0(5)
UCSZ10/UCPHA0(5)
UCPOL1
187/201
UDRIE1
RXEN1
TXEN1
UCSZ12
RXB81
TXB81
186/200
UDRE1
FE1
DOR1
UPE1
U2X1
MPCM1
185/200
-
-
-
-
-
-
-
-
-
-
-
Reserved
-
-
-
(0xC2)
UCSR0C
UMSEL01
UMSEL00
(0xC1)
UCSR0B
RXCIE0
TXCIE0
USART0 I/O Data Register
185
USART0 Baud Rate Register High Byte
189/202
USART0 Baud Rate Register Low Byte
189/202
-
-
-
-
-
UPM01
UPM00
USBS0
UCSZ01/UDORD0(5)
UCSZ00/UCPHA0(5)
UCPOL0
187/201
UDRIE0
RXEN0
TXEN0
UCSZ02
RXB80
TXB80
186/200
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
10
Address
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Page
(0xC0)
UCSR0A
Name
RXC0
TXC0
UDRE0
FE0
DOR0
UPE0
U2X0
MPCM0
185/200
(0xBF)
Reserved
-
-
-
-
-
-
-
-
(0xBE)
Reserved
-
-
-
-
-
-
-
-
(0xBD)
TWAMR
TWAM6
TWAM5
TWAM4
TWAM3
TWAM2
TWAM1
TWAM0
-
231
(0xBC)
TWCR
TWINT
TWEA
TWSTA
TWSTO
TWWC
TWEN
-
TWIE
228
(0xBB)
TWDR
(0xBA)
TWAR
TWA6
TWA5
TWA4
TWA3
TWA2
TWA1
TWA0
TWGCE
231
(0xB9)
TWSR
TWS7
TWS6
TWS5
TWS4
TWS3
-
TWPS1
TWPS0
229
two-wire Serial Interface Data Register
230
(0xB8)
TWBR
(0xB7)
Reserved
-
-
-
two-wire Serial Interface Bit Rate Register
-
-
-
-
-
228
(0xB6)
ASSR
-
EXCLK
AS2
TCN2UB
OCR2AUB
OCR2BUB
TCR2AUB
TCR2BUB
(0xB5)
Reserved
-
-
-
-
-
-
-
-
(0xB4)
OCR2B
Timer/Counter2 Output Compare Register B
(0xB3)
OCR2A
Timer/Counter2 Output Compare Register A
155
(0xB2)
TCNT2
Timer/Counter2 (8 Bit)
154
155
155
(0xB1)
TCCR2B
FOC2A
FOC2B
-
-
WGM22
CS22
CS21
CS20
153
(0xB0)
TCCR2A
COM2A1
COM2A0
COM2B1
COM2B0
-
-
WGM21
WGM20
151
(0xAF)
Reserved
-
-
-
-
-
-
-
-
(0xAE)
Reserved
-
-
-
-
-
-
-
-
(0xAD)
Reserved
-
-
-
-
-
-
-
-
(0xAC)
Reserved
-
-
-
-
-
-
-
-
(0xAB)
Reserved
-
-
-
-
-
-
-
-
(0xAA)
Reserved
-
-
-
-
-
-
-
-
(0xA9)
Reserved
-
-
-
-
-
-
-
-
(0xA8)
Reserved
-
-
-
-
-
-
-
-
(0xA7)
Reserved
-
-
-
-
-
-
-
-
(0xA6)
Reserved
-
-
-
-
-
-
-
-
(0xA5)
Reserved
-
-
-
-
-
-
-
-
(0xA4)
Reserved
-
-
-
-
-
-
-
-
(0xA3)
Reserved
-
-
-
-
-
-
-
-
(0xA2)
Reserved
-
-
-
-
-
-
-
-
(0xA1)
Reserved
-
-
-
-
-
-
-
-
(0xA0)
Reserved
-
-
-
-
-
-
-
-
(0x9F)
Reserved
-
-
-
-
-
-
-
-
(0x9E)
Reserved
-
-
-
-
-
-
-
-
(0x9D)
Reserved
-
-
-
-
-
-
-
-
(0x9C)
Reserved
-
-
-
-
-
-
-
-
(0x9B)
OCR3BH
Timer/Counter3 - Output Compare Register B High Byte(7)
132
(0x9A)
OCR3BL
Timer/Counter3 - Output Compare Register B Low Byte(7)
132
(0x99)
OCR3AH
Timer/Counter3 - Output Compare Register A High Byte(7)
132
(0x98)
OCR3AL
Timer/Counter3 - Output Compare Register A Low Byte(7)
132
(0x97)
ICR3H
Timer/Counter3 - Input Capture Register High Byte(7)
133
(0x96)
ICR3L
Timer/Counter3 - Input Capture Register Low Byte(7)
133
(0x95)
TCNT3H
Timer/Counter3 - Counter Register High Byte(7)
132
(0x94)
TCNT3L
Timer/Counter3 - Counter Register Low Byte(7)
(0x93)
Reserved
-
-
-
(0x92)
TCCR3C
FOC3A
FOC3B
-
-
-
-
-
-
131
(0x91)
TCCR3B
ICNC3
ICES3
-
WGM33
WGM32
CS32
CS31
CS30
130
(0x90)
TCCR3A
COM3A1
COM3A0
COM3B1
COM3B0
-
-
WGM31
WGM30
128
(0x8F)
Reserved
-
-
-
-
-
-
-
-
-
-
-
132
-
-
(0x8E)
Reserved
-
-
-
-
-
-
-
-
(0x8D)
Reserved
-
-
-
-
-
-
-
-
(0x8C)
Reserved
-
-
-
-
-
-
-
-
(0x8B)
OCR1BH
Timer/Counter1 - Output Compare Register B High Byte
132
(0x8A)
OCR1BL
Timer/Counter1 - Output Compare Register B Low Byte
132
(0x89)
OCR1AH
Timer/Counter1 - Output Compare Register A High Byte
132
(0x88)
OCR1AL
Timer/Counter1 - Output Compare Register A Low Byte
132
(0x87)
ICR1H
Timer/Counter1 - Input Capture Register High Byte
133
(0x86)
ICR1L
Timer/Counter1 - Input Capture Register Low Byte
133
(0x85)
TCNT1H
Timer/Counter1 - Counter Register High Byte
132
(0x84)
TCNT1L
Timer/Counter1 - Counter Register Low Byte
(0x83)
Reserved
-
-
-
(0x82)
TCCR1C
FOC1A
FOC1B
-
-
-
-
-
-
131
(0x81)
TCCR1B
ICNC1
ICES1
-
WGM13
WGM12
CS12
CS11
CS10
130
(0x80)
TCCR1A
COM1A1
COM1A0
COM1B1
COM1B0
-
-
WGM11
WGM10
128
(0x7F)
DIDR1
-
-
-
-
-
-
AIN1D
AIN0D
234
(0x7E)
DIDR0
ADC7D
ADC6D
ADC5D
ADC4D
ADC3D
ADC2D
ADC1D
ADC0D
253
(0x7D)
Reserved
-
-
-
-
-
-
-
-
-
-
-
132
-
-
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
11
Address
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Page
(0x7C)
ADMUX
Name
REFS1
REFS0
ADLAR
MUX4
MUX3
MUX2
MUX1
MUX0
249
(0x7B)
ADCSRB
-
ACME
-
-
-
ADTS2
ADTS1
ADTS0
233
(0x7A)
ADCSRA
ADEN
ADSC
ADATE
ADIF
ADIE
ADPS2
ADPS1
ADPS0
250
(0x79)
ADCH
ADC Data Register High byte
(0x78)
ADCL
ADC Data Register Low byte
(0x77)
Reserved
-
-
-
-
-
-
-
-
(0x76)
Reserved
-
-
-
-
-
-
-
-
(0x75)
Reserved
-
-
-
-
-
-
-
-
(0x74)
Reserved
-
-
-
-
-
-
-
-
(0x73)
PCMSK3
PCINT31
PCINT30
PCINT29
PCINT28
PCINT27
PCINT26
PCINT25
PCINT24
(0x72)
Reserved
-
-
-
-
-
-
-
-
(0x71)
TIMSK3
-
-
ICIE3
-
-
OCIE3B
OCIE3A
TOIE3
134
(0x70)
TIMSK2
-
-
-
-
-
OCIE2B
OCIE2A
TOIE2
156
(0x6F)
TIMSK1
-
-
ICIE1
-
-
OCIE1B
OCIE1A
TOIE1
134
(0x6E)
TIMSK0
-
-
-
-
-
OCIE0B
OCIE0A
TOIE0
105
(0x6D)
PCMSK2
PCINT23
PCINT22
PCINT21
PCINT20
PCINT19
PCINT18
PCINT17
PCINT16
70
(0x6C)
PCMSK1
PCINT15
PCINT14
PCINT13
PCINT12
PCINT11
PCINT10
PCINT9
PCINT8
70
(0x6B)
PCMSK0
PCINT7
PCINT6
PCINT5
PCINT4
PCINT3
PCINT2
PCINT1
PCINT0
71
(0x6A)
Reserved
-
-
-
-
-
-
-
-
(0x69)
EICRA
-
-
ISC21
ISC20
ISC11
ISC10
ISC01
ISC00
67
(0x68)
PCICR
-
-
-
-
PCIE3
PCIE2
PCIE1
PCIE0
69
(0x67)
Reserved
-
-
-
-
-
-
-
-
251
251
Oscillator Calibration Register
70
(0x66)
OSCCAL
(0x65)
PRR1
-
-
-
-
-
-
-
--PRTIM3
40
49
(0x64)
PRR0
PRTWI
PRTIM2
PRTIM0
PRUSART1
PRTIM1
PRSPI
PRUSART0
PRADC
48
(0x63)
Reserved
-
-
-
-
-
-
-
-
(0x62)
Reserved
(0x61)
CLKPR
(0x60)
WDTCSR
-
-
-
-
-
-
-
-
CLKPCE
-
-
-
CLKPS3
CLKPS2
CLKPS1
CLKPS0
40
WDIF
WDIE
WDP3
WDCE
WDE
WDP2
WDP1
WDP0
59
I
T
H
S
V
N
Z
C
11
0x3F (0x5F)
SREG
0x3E (0x5E)
SPH
SP15
SP14
SP13
SP12
SP11
SP10
SP9
SP8
12
0x3D (0x5D)
SPL
SP7
SP6
SP5
SP4
SP3
SP2
SP1
SP0
12
0x3C (0x5C)
Reserved
-
-
-
-
-
-
-
-
0x3B (0x5B)
Reserved
-
-
-
-
-
-
-
-
0x3A (0x5A)
Reserved
-
-
-
-
-
-
-
-
0x39 (0x59)
Reserved
-
-
-
-
-
-
-
-
0x38 (0x58)
Reserved
-
-
-
-
-
-
-
-
0x37 (0x57)
SPMCSR
SPMIE
RWWSB
SIGRD
RWWSRE
BLBSET
PGWRT
PGERS
SPMEN
0x36 (0x56)
Reserved
-
-
-
-
-
-
-
-
0x35 (0x55)
MCUCR
JTD
BODS(6)
BODSE(6)
PUD
-
-
IVSEL
IVCE
89/268
0x34 (0x54)
MCUSR
-
-
-
JTRF
WDRF
BORF
EXTRF
PORF
58/268
0x33 (0x53)
SMCR
-
-
-
-
SM2
SM1
SM0
SE
47
0x32 (0x52)
Reserved
-
-
-
-
-
-
-
-
0x31 (0x51)
OCDR
0x30 (0x50)
ACSR
ACD
ACBG
ACO
ACI
ACIE
ACIC
ACIS1
ACIS0
0x2F (0x4F)
Reserved
-
-
-
-
-
-
-
-
On-Chip Debug Register
285
259
SPI 0 Data Register
250
0x2E (0x4E)
SPDR
0x2D (0x4D)
SPSR
SPIF0
WCOL0
-
-
-
-
-
SPI2X0
165
0x2C (0x4C)
SPCR
SPIE0
SPE0
DORD0
MSTR0
CPOL0
CPHA0
SPR01
SPR00
164
0x2B (0x4B)
GPIOR2
General Purpose I/O Register 2
0x2A (0x4A)
GPIOR1
General Purpose I/O Register 1
0x29 (0x49)
Reserved
0x28 (0x48)
OCR0B
Timer/Counter0 Output Compare Register B
105
0x27 (0x47)
OCR0A
Timer/Counter0 Output Compare Register A
105
0x26 (0x46)
TCNT0
Timer/Counter0 (8 Bit)
0x25 (0x45)
TCCR0B
FOC0A
FOC0B
-
-
WGM02
CS02
CS01
CS00
104
0x24 (0x44)
TCCR0A
COM0A1
COM0A0
COM0B1
COM0B0
-
-
WGM01
WGM00
105
0x23 (0x43)
GTCCR
TSM
-
-
-
-
-
PSRASY
PSRSYNC
157
0x22 (0x42)
EEARH
-
-
-
-
0x21 (0x41)
EEARL
EEPROM Address Register Low Byte
0x20 (0x40)
EEDR
EEPROM Data Register
0x1F (0x3F)
EECR
0x1E (0x3E)
GPIOR0
0x1D (0x3D)
EIMSK
-
-
-
-
-
0x1C (0x3C)
EIFR
-
-
-
-
0x1B (0x3B)
PCIFR
-
-
-
0x1A (0x3A)
Reserved
-
-
0x19 (0x39)
Reserved
-
-
-
-
-
-
-
EEPM1
-
166
29
29
-
-
-
-
105
EEPROM Address Register High Byte
EEPM0
EERIE
24
24
24
EEMPE
EEPE
EERE
INT2
INT1
INT0
68
-
INTF2
INTF1
INTF0
68
-
PCIF3
PCIF2
PCIF1
PCIF0
69
-
-
-
-
-
-
-
-
-
-
-
-
General Purpose I/O Register 0
24
29
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
12
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Page
0x18 (0x38)
Address
TIFR3
Name
-
-
ICF3
-
-
OCF3B
OCF3A
TOV3
136
0x17 (0x37)
TIFR2
-
-
-
-
-
OCF2B
OCF2A
TOV2
156
0x16 (0x36)
TIFR1
-
-
ICF1
-
-
OCF1B
OCF1A
TOV1
135
0x15 (0x35)
TIFR0
-
-
-
-
-
OCF0B
OCF0A
TOV0
106
0x14 (0x34)
Reserved
-
-
-
-
-
-
-
-
0x13 (0x33)
Reserved
-
-
-
-
-
-
-
-
0x12 (0x32)
Reserved
-
-
-
-
-
-
-
-
0x11 (0x31)
Reserved
-
-
-
-
-
-
-
-
0x10 (0x30)
Reserved
-
-
-
-
-
-
-
-
0x0F (0x2F)
Reserved
-
-
-
-
-
-
-
-
0x0E (0x2E)
Reserved
-
-
-
-
-
-
-
-
0x0D (0x2D)
Reserved
-
-
-
-
-
-
-
-
0x0C (0x2C)
Reserved
-
-
-
-
-
-
-
-
0x0B (0x2B)
PORTD
PORTD7
PORTD6
PORTD5
PORTD4
PORTD3
PORTD2
PORTD1
PORTD0
90
0x0A (0x2A)
DDRD
DDD7
DDD6
DDD5
DDD4
DDD3
DDD2
DDD1
DDD0
90
0x09 (0x29)
PIND
PIND7
PIND6
PIND5
PIND4
PIND3
PIND2
PIND1
PIND0
90
0x08 (0x28)
PORTC
PORTC7
PORTC6
PORTC5
PORTC4
PORTC3
PORTC2
PORTC1
PORTC0
90
0x07 (0x27)
DDRC
DDC7
DDC6
DDC5
DDC4
DDC3
DDC2
DDC1
DDC0
90
0x06 (0x26)
PINC
PINC7
PINC6
PINC5
PINC4
PINC3
PINC2
PINC1
PINC0
90
0x05 (0x25)
PORTB
PORTB7
PORTB6
PORTB5
PORTB4
PORTB3
PORTB2
PORTB1
PORTB0
89
0x04 (0x24)
DDRB
DDB7
DDB6
DDB5
DDB4
DDB3
DDB2
DDB1
DDB0
89
0x03 (0x23)
PINB
PINB7
PINB6
PINB5
PINB4
PINB3
PINB2
PINB1
PINB0
90
0x02 (0x22)
PORTA
PORTA7
PORTA6
PORTA5
PORTA4
PORTA3
PORTA2
PORTA1
PORTA0
89
0x01 (0x21)
DDRA
DDA7
DDA6
DDA5
DDA4
DDA3
DDA2
DDA1
DDA0
89
0x00 (0x20)
PINA
PINA7
PINA6
PINA5
PINA4
PINA3
PINA2
PINA1
PINA0
89
Notes:
1. For compatibility with future devices, reserved bits should be written to zero if accessed. Reserved I/O memory
addresses should never be written.
2. I/O registers within the address range $00 - $1F are directly bit-accessible using the SBI and CBI instructions. In these
registers, the value of single bits can be checked by using the SBIS and SBIC instructions.
3. Some of the status flags are cleared by writing a logical one to them. Note that the CBI and SBI instructions will operate
on all bits in the I/O register, writing a one back into any flag read as set, thus clearing the flag. The CBI and SBI
instructions work with registers 0x00 to 0x1F only.
4. When using the I/O specific commands IN and OUT, the I/O addresses $00 - $3F must be used. When addressing I/O
registers as data space using LD and ST instructions, $20 must be added to these addresses.
The ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P is a complex microcontroller with more peripheral units
than can be supported within the 64 location reserved in Opcode for the IN and OUT instructions. For the Extended I/O
space from $60 - $FF, only the ST/STS/STD and LD/LDS/LDD instructions can be used.
5. USART in SPI Master Mode.
6. Only available in the ATmega164PA/324PA/644PA/1284P.
7. Only available in the ATmega1284/1284P
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
13
8.
Instruction set summary
Mnemonics
Operands
Description
Operation
Flags
#Clocks
ARITHMETIC AND LOGIC INSTRUCTIONS
ADD
Rd, Rr
Add two Registers
Rd ← Rd + Rr
Z,C,N,V,H
1
ADC
Rd, Rr
Add with Carry two Registers
Rd ← Rd + Rr + C
Z,C,N,V,H
1
2
ADIW
Rdl,K
Add Immediate to Word
Rdh:Rdl ← Rdh:Rdl + K
Z,C,N,V,S
SUB
Rd, Rr
Subtract two Registers
Rd ← Rd - Rr
Z,C,N,V,H
1
SUBI
Rd, K
Subtract Constant from Register
Rd ← Rd - K
Z,C,N,V,H
1
SBC
Rd, Rr
Subtract with Carry two Registers
Rd ← Rd - Rr - C
Z,C,N,V,H
1
SBCI
Rd, K
Subtract with Carry Constant from Reg.
Rd ← Rd - K - C
Z,C,N,V,H
1
SBIW
Rdl,K
Subtract Immediate from Word
Rdh:Rdl ← Rdh:Rdl - K
Z,C,N,V,S
2
AND
Rd, Rr
Logical AND Registers
Rd ← Rd • Rr
Z,N,V
1
ANDI
Rd, K
Logical AND Register and Constant
Rd ← Rd • K
Z,N,V
1
OR
Rd, Rr
Logical OR Registers
Rd ← Rd v Rr
Z,N,V
1
ORI
Rd, K
Logical OR Register and Constant
Rd ← Rd v K
Z,N,V
1
EOR
Rd, Rr
Exclusive OR Registers
Rd ← Rd ⊕ Rr
Z,N,V
1
COM
Rd
One’s Complement
Rd ← 0xFF − Rd
Z,C,N,V
1
NEG
Rd
Two’s Complement
Rd ← 0x00 − Rd
Z,C,N,V,H
1
SBR
Rd,K
Set Bit(s) in Register
Rd ← Rd v K
Z,N,V
1
CBR
Rd,K
Clear Bit(s) in Register
Rd ← Rd • (0xFF - K)
Z,N,V
1
INC
Rd
Increment
Rd ← Rd + 1
Z,N,V
1
DEC
Rd
Decrement
Rd ← Rd − 1
Z,N,V
1
TST
Rd
Test for Zero or Minus
Rd ← Rd • Rd
Z,N,V
1
CLR
Rd
Clear Register
Rd ← Rd ⊕ Rd
Z,N,V
1
SER
Rd
Set Register
Rd ← 0xFF
None
1
MUL
Rd, Rr
Multiply Unsigned
R1:R0 ← Rd x Rr
Z,C
2
MULS
Rd, Rr
Multiply Signed
R1:R0 ← Rd x Rr
Z,C
2
MULSU
Rd, Rr
Multiply Signed with Unsigned
R1:R0 ← Rd x Rr
Z,C
2
FMUL
Rd, Rr
Fractional Multiply Unsigned
R1:R0 ← (Rd x Rr) << 1
Z,C
2
FMULS
Rd, Rr
Fractional Multiply Signed
R1:R0 ← (Rd x Rr) << 1
Z,C
2
FMULSU
Rd, Rr
Fractional Multiply Signed with Unsigned
R1:R0 ← (Rd x Rr) << 1
Z,C
2
Relative Jump
PC ← PC + k + 1
None
2
Indirect Jump to (Z)
PC ← Z
None
2
3
BRANCH INSTRUCTIONS
RJMP
k
IJMP
JMP
k
Direct Jump
PC ← k
None
RCALL
k
Relative Subroutine Call
PC ← PC + k + 1
None
3
Indirect Call to (Z)
PC ← Z
None
3
ICALL
CALL
k
RET
Direct Subroutine Call
PC ← k
None
4
Subroutine Return
PC ← STACK
None
4
Interrupt Return
PC ← STACK
I
CPSE
Rd,Rr
Compare, Skip if Equal
if (Rd = Rr) PC ← PC + 2 or 3
None
CP
Rd,Rr
Compare
Rd − Rr
Z, N,V,C,H
1
CPC
Rd,Rr
Compare with Carry
Rd − Rr − C
Z, N,V,C,H
1
CPI
Rd,K
Compare Register with Immediate
Rd − K
Z, N,V,C,H
SBRC
Rr, b
Skip if Bit in Register Cleared
if (Rr(b)=0) PC ← PC + 2 or 3
None
RETI
4
1/2/3
1
1/2/3
SBRS
Rr, b
Skip if Bit in Register is Set
if (Rr(b)=1) PC ← PC + 2 or 3
None
1/2/3
SBIC
P, b
Skip if Bit in I/O Register Cleared
if (P(b)=0) PC ← PC + 2 or 3
None
1/2/3
SBIS
P, b
Skip if Bit in I/O Register is Set
if (P(b)=1) PC ← PC + 2 or 3
None
1/2/3
BRBS
s, k
Branch if Status Flag Set
if (SREG(s) = 1) then PC←PC+k + 1
None
1/2
BRBC
s, k
Branch if Status Flag Cleared
if (SREG(s) = 0) then PC←PC+k + 1
None
1/2
BREQ
k
Branch if Equal
if (Z = 1) then PC ← PC + k + 1
None
1/2
BRNE
k
Branch if Not Equal
if (Z = 0) then PC ← PC + k + 1
None
1/2
BRCS
k
Branch if Carry Set
if (C = 1) then PC ← PC + k + 1
None
1/2
BRCC
k
Branch if Carry Cleared
if (C = 0) then PC ← PC + k + 1
None
1/2
BRSH
k
Branch if Same or Higher
if (C = 0) then PC ← PC + k + 1
None
1/2
BRLO
k
Branch if Lower
if (C = 1) then PC ← PC + k + 1
None
1/2
BRMI
k
Branch if Minus
if (N = 1) then PC ← PC + k + 1
None
1/2
BRPL
k
Branch if Plus
if (N = 0) then PC ← PC + k + 1
None
1/2
BRGE
k
Branch if Greater or Equal, Signed
if (N ⊕ V= 0) then PC ← PC + k + 1
None
1/2
BRLT
k
Branch if Less Than Zero, Signed
if (N ⊕ V= 1) then PC ← PC + k + 1
None
1/2
BRHS
k
Branch if Half Carry Flag Set
if (H = 1) then PC ← PC + k + 1
None
1/2
BRHC
k
Branch if Half Carry Flag Cleared
if (H = 0) then PC ← PC + k + 1
None
1/2
BRTS
k
Branch if T Flag Set
if (T = 1) then PC ← PC + k + 1
None
1/2
BRTC
k
Branch if T Flag Cleared
if (T = 0) then PC ← PC + k + 1
None
1/2
BRVS
k
Branch if Overflow Flag is Set
if (V = 1) then PC ← PC + k + 1
None
1/2
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
14
Mnemonics
Operands
Description
Operation
Flags
#Clocks
BRVC
k
Branch if Overflow Flag is Cleared
if (V = 0) then PC ← PC + k + 1
None
1/2
BRIE
k
Branch if Interrupt Enabled
if ( I = 1) then PC ← PC + k + 1
None
1/2
BRID
k
Branch if Interrupt Disabled
if ( I = 0) then PC ← PC + k + 1
None
1/2
BIT AND BIT-TEST INSTRUCTIONS
SBI
P,b
Set Bit in I/O Register
I/O(P,b) ← 1
None
2
CBI
P,b
Clear Bit in I/O Register
I/O(P,b) ← 0
None
2
LSL
Rd
Logical Shift Left
Rd(n+1) ← Rd(n), Rd(0) ← 0
Z,C,N,V
1
LSR
Rd
Logical Shift Right
Rd(n) ← Rd(n+1), Rd(7) ← 0
Z,C,N,V
1
ROL
Rd
Rotate Left Through Carry
Rd(0)←C,Rd(n+1)← Rd(n),C←Rd(7)
Z,C,N,V
1
ROR
Rd
Rotate Right Through Carry
Rd(7)←C,Rd(n)← Rd(n+1),C←Rd(0)
Z,C,N,V
1
ASR
Rd
Arithmetic Shift Right
Rd(n) ← Rd(n+1), n=0..6
Z,C,N,V
1
SWAP
Rd
Swap Nibbles
Rd(3..0)←Rd(7..4),Rd(7..4)←Rd(3..0)
None
1
BSET
s
Flag Set
SREG(s) ← 1
SREG(s)
1
BCLR
s
Flag Clear
SREG(s) ← 0
SREG(s)
1
BST
Rr, b
Bit Store from Register to T
T ← Rr(b)
T
1
BLD
Rd, b
Bit load from T to Register
Rd(b) ← T
None
1
SEC
Set Carry
C←1
C
1
CLC
Clear Carry
C←0
C
1
SEN
Set Negative Flag
N←1
N
1
CLN
Clear Negative Flag
N←0
N
1
SEZ
Set Zero Flag
Z←1
Z
1
CLZ
Clear Zero Flag
Z←0
Z
1
SEI
Global Interrupt Enable
I←1
I
1
CLI
Global Interrupt Disable
I←0
I
1
SES
Set Signed Test Flag
S←1
S
1
CLS
Clear Signed Test Flag
S←0
S
1
SEV
Set Twos Complement Overflow.
V←1
V
1
CLV
Clear Twos Complement Overflow
V←0
V
1
SET
Set T in SREG
T←1
T
1
CLT
Clear T in SREG
T←0
T
1
SEH
CLH
Set Half Carry Flag in SREG
Clear Half Carry Flag in SREG
H←1
H←0
H
H
1
1
Rd ← Rr
Rd+1:Rd ← Rr+1:Rr
None
1
None
1
DATA TRANSFER INSTRUCTIONS
MOV
Rd, Rr
Move Between Registers
MOVW
Rd, Rr
Copy Register Word
LDI
Rd, K
Load Immediate
Rd ← K
None
1
LD
Rd, X
Load Indirect
Rd ← (X)
None
2
LD
Rd, X+
Load Indirect and Post-Inc.
Rd ← (X), X ← X + 1
None
2
LD
Rd, - X
Load Indirect and Pre-Dec.
X ← X - 1, Rd ← (X)
None
2
LD
Rd, Y
Load Indirect
Rd ← (Y)
None
2
LD
Rd, Y+
Load Indirect and Post-Inc.
Rd ← (Y), Y ← Y + 1
None
2
LD
Rd, - Y
Load Indirect and Pre-Dec.
Y ← Y - 1, Rd ← (Y)
None
2
LDD
Rd,Y+q
Load Indirect with Displacement
Rd ← (Y + q)
None
2
LD
Rd, Z
Load Indirect
Rd ← (Z)
None
2
LD
Rd, Z+
Load Indirect and Post-Inc.
Rd ← (Z), Z ← Z+1
None
2
LD
Rd, -Z
Load Indirect and Pre-Dec.
Z ← Z - 1, Rd ← (Z)
None
2
LDD
Rd, Z+q
Load Indirect with Displacement
Rd ← (Z + q)
None
2
LDS
Rd, k
Load Direct from SRAM
Rd ← (k)
None
2
ST
X, Rr
Store Indirect
(X) ← Rr
None
2
ST
X+, Rr
Store Indirect and Post-Inc.
(X) ← Rr, X ← X + 1
None
2
ST
- X, Rr
Store Indirect and Pre-Dec.
X ← X - 1, (X) ← Rr
None
2
ST
Y, Rr
Store Indirect
(Y) ← Rr
None
2
ST
Y+, Rr
Store Indirect and Post-Inc.
(Y) ← Rr, Y ← Y + 1
None
2
ST
- Y, Rr
Store Indirect and Pre-Dec.
Y ← Y - 1, (Y) ← Rr
None
2
STD
Y+q,Rr
Store Indirect with Displacement
(Y + q) ← Rr
None
2
ST
Z, Rr
Store Indirect
(Z) ← Rr
None
2
ST
Z+, Rr
Store Indirect and Post-Inc.
(Z) ← Rr, Z ← Z + 1
None
2
ST
-Z, Rr
Store Indirect and Pre-Dec.
Z ← Z - 1, (Z) ← Rr
None
2
STD
Z+q,Rr
Store Indirect with Displacement
(Z + q) ← Rr
None
2
STS
k, Rr
Store Direct to SRAM
(k) ← Rr
None
2
Load Program Memory
R0 ← (Z)
None
3
LPM
Rd, Z
Load Program Memory
Rd ← (Z)
None
3
LPM
Rd, Z+
Load Program Memory and Post-Inc
Rd ← (Z), Z ← Z+1
None
3
Store Program Memory
(Z) ← R1:R0
None
-
In Port
Rd ← P
None
1
1
LPM
SPM
IN
Rd, P
OUT
P, Rr
Out Port
P ← Rr
None
PUSH
Rr
Push Register on Stack
STACK ← Rr
None
2
POP
Rd
Pop Register from Stack
Rd ← STACK
None
2
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
15
Mnemonics
Operands
Description
Operation
Flags
#Clocks
MCU CONTROL INSTRUCTIONS
NOP
No Operation
None
1
SLEEP
Sleep
(see specific descr. for Sleep function)
None
1
WDR
BREAK
Watchdog Reset
Break
(see specific descr. for WDR/timer)
For On-chip Debug Only
None
None
1
N/A
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
16
9.
Ordering information
9.1
Atmel ATmega164A
Speed [MHz] (3)
20
Notes:
Power supply
1.8 - 5.5V
Ordering code (2)
Package (1)
ATmega164A-AU
ATmega164A-AUR(5)
ATmega164A-PU
ATmega164A-MU
ATmega164A-MUR(5)
ATmega164A-MCH(4)
ATmega164A-MCHR(4)(5)
ATmega164A-CU
ATmega164A-CUR(5)
44A
44A
40P6
44M1
44M1
44MC
44MC
49C2
49C2
Operational range
Industrial
(-40oC to 85oC)
1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering
information and minimum quantities.
2. Pb-free packaging, complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also
Halide free and fully Green.
3. For Speed vs. VCC see ”Speed grades” on page 324.
4. NiPdAu Lead Finish.
5. Tape & Reel.
Package Type
44A
44-lead, Thin (1.0mm) Plastic Gull Wing Quad Flat Package (TQFP)
40P6
40-pin, 0.600” Wide, Plastic Dual Inline Package (PDIP)
44M1
44-pad, 7 × 7 × 1.0mm body, lead pitch 0.50mm, Thermally Enhanced Plastic Very Thin Quad Flat No-Lead (VQFN)
44MC
44-lead (2-row Staggered), 5 × 5 × 1.0mm body, 2.60 × 2.60mm Exposed Pad, Quad Flat No-Lead Package (QFN)
49C2
49-ball, (7 × 7 Array) 0.65mm Pitch, 5 × 5 × 1mm, Very Thin, Fine-Pitch Ball Grid Array Package (VFBGA)
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
17
9.2
Atmel ATmega164PA
Speed [MHz] (3)
20
Notes:
Power supply
1.8 - 5.5V
Ordering code (2)
Package (1)
ATmega164PA-AU
ATmega164PA-AUR(5)
ATmega164PA-PU
ATmega164PA-MU
ATmega164PA-MUR(5)
ATmega164PA-MCH(4)
ATmega164PA-MCHR(4)(5)
ATmega164PA-CU
ATmega164PA-CUR(5)
44A
44A
40P6
44M1
44M1
44MC
44MC
49C2
49C2
Operational range
Industrial
(-40oC to 85oC)
1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering
information and minimum quantities.
2. Pb-free packaging, complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also
Halide free and fully Green.
3. For Speed vs. VCC see ”Speed grades” on page 324.
4. NiPdAu Lead Finish.
5. Tape & Reel.
Package Type
44A
44-lead, Thin (1.0mm) Plastic Gull Wing Quad Flat Package (TQFP)
40P6
40-pin, 0.600” Wide, Plastic Dual Inline Package (PDIP)
44M1
44-pad, 7 × 7 × 1.0mm body, lead pitch 0.50mm, Thermally Enhanced Plastic Very Thin Quad Flat No-Lead (VQFN)
44MC
44-lead (2-row Staggered), 5 × 5 × 1.0mm body, 2.60 × 2.60mm Exposed Pad, Quad Flat No-Lead Package (QFN)
49C2
49-ball, (7 × 7 Array) 0.65mm Pitch, 5 × 5 × 1mm, Very Thin, Fine-Pitch Ball Grid Array Package (VFBGA)
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
18
9.3
Atmel ATmega324A
Speed [MHz] (3)
20
Notes:
Power supply
1.8 - 5.5V
Ordering code (2)
Package (1)
ATmega324A-AU
ATmega324A-AUR(5)
ATmega324A-PU
ATmega324A-MU
ATmega324A-MUR(5)
ATmega324A-MCH(4)
ATmega324A-MCHR(4)(5)
ATmega324A-CU
ATmega324A-CUR(5)
44A
44A
40P6
44M1
44M1
44MC
44MC
49C2
49C2
Operational range
Industrial
(-40oC to 85oC)
1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering
information and minimum quantities.
2. Pb-free packaging, complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also
Halide free and fully Green.
3. For Speed vs. VCC see ”Speed grades” on page 324.
4. NiPdAu Lead Finish.
5. Tape & Reel.
Package Type
44A
44-lead, Thin (1.0mm) Plastic Gull Wing Quad Flat Package (TQFP)
40P6
40-pin, 0.600” Wide, Plastic Dual Inline Package (PDIP)
44M1
44-pad, 7 × 7 × 1.0mm body, lead pitch 0.50mm, Thermally Enhanced Plastic Very Thin Quad Flat No-Lead (VQFN)
44MC
44-lead (2-row Staggered), 5 × 5 × 1.0mm body, 2.60 × 2.60mm Exposed Pad, Quad Flat No-Lead Package (QFN)
49C2
49-ball, (7 × 7 Array) 0.65mm Pitch, 5 × 5 × 1mm, Very Thin, Fine-Pitch Ball Grid Array Package (VFBGA)
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
19
9.4
Atmel ATmega324PA
Speed [MHz] (3)
20
Notes:
Power supply
1.8 - 5.5V
Ordering code (2)
Package (1)
ATmega324PA-AU
ATmega324PA-AUR(5)
ATmega324PA-PU
ATmega324PA-MU
ATmega324PA-MUR(5)
ATmega324PA-MCH(4)
ATmega324PA-MCHR(4)(5)
ATmega324PA-CU
ATmega324PA-CUR(5)
44A
44A
40P6
44M1
44M1
44MC
44MC
49C2
49C2
Operational range
Industrial
(-40oC to 85oC)
1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering
information and minimum quantities.
2. Pb-free packaging, complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also
Halide free and fully Green.
3. For Speed vs. VCC see ”Speed grades” on page 324.
4. NiPdAu Lead Finish.
5. Tape & Reel.
Package Type
44A
44-lead, Thin (1.0mm) Plastic Gull Wing Quad Flat Package (TQFP)
40P6
40-pin, 0.600” Wide, Plastic Dual Inline Package (PDIP)
44M1
44-pad, 7 × 7 × 1.0mm body, lead pitch 0.50mm, Thermally Enhanced Plastic Very Thin Quad Flat No-Lead (VQFN)
44MC
44-lead (2-row Staggered), 5 × 5 × 1.0mm body, 2.60 × 2.60mm Exposed Pad, Quad Flat No-Lead Package (QFN)
49C2
49-ball, (7 × 7 Array) 0.65mm Pitch, 5 × 5 × 1mm, Very Thin, Fine-Pitch Ball Grid Array Package (VFBGA)
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
20
9.5
Atmel ATmega644A
Speed [MHz](3)
20
Notes:
Power supply
1.8 - 5.5V
Ordering code(2)
Package(1)
ATmega644A-AU
ATmega644A-AUR(4)
ATmega644A-PU
ATmega644A-MU
ATmega644A-MUR(4)
44A
44A
40P6
44M1
44M1
Operational range
Industrial
(-40oC to 85oC)
1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering
information and minimum quantities.
2. Pb-free packaging, complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also
Halide free and fully Green.
3. For Speed vs. VCC see ”Speed grades” on page 324.
4. Taper & Reel.
Package Type
44A
44-lead, Thin (1.0mm) Plastic Gull Wing Quad Flat Package (TQFP)
40P6
40-pin, 0.600” Wide, Plastic Dual Inline Package (PDIP)
44M1
44-pad, 7 × 7 × 1.0mm body, lead pitch 0.5 mm, Thermally Enhanced Plastic Very Thin Quad Flat No-Lead (VQFN)
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
21
9.6
Atmel ATmega644PA
Speed [MHz] (3)
20
Notes:
Power supply
1.8 - 5.5V
Ordering code (2)
Package (1)
ATmega644PA-AU
ATmega644PA-AUR(4)
ATmega644PA-PU
ATmega644PA-MU
ATmega644PA-MUR(4)
44A
44A
40P6
44M1
44M1
Operational range
Industrial
(-40oC to 85oC)
1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering
information and minimum quantities.
2. Pb-free packaging, complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also
Halide free and fully Green.
3. For Speed vs. VCC see ”Speed grades” on page 324.
4. Taper & Reel.
Package Type
44A
44-lead, Thin (1.0mm) Plastic Gull Wing Quad Flat Package (TQFP)
40P6
40-pin, 0.600” Wide, Plastic Dual Inline Package (PDIP)
44M1
44-pad, 7 × 7 × 1.0mm body, lead pitch 0.50mm, Thermally Enhanced Plastic Very Thin Quad Flat No-Lead (VQFN)
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
22
9.7
Atmel ATmega1284
Speed [MHz](3)
20
Notes:
Power supply
1.8 - 5.5V
Ordering code(2)
Package(1)
ATmega1284-AU
ATmega1284-AUR(4)
ATmega1284-PU
ATmega1284-MU
ATmega1284-MUR(4)
44A
44A
40P6
44M1
44M1
Operational range
Industrial
(-40oC to 85oC)
1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering
information and minimum quantities.
2. Pb-free packaging, complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also
Halide free and fully Green.
3. For Speed vs. VCC see ”Speed grades” on page 324.
4. Tape & Reel.
Package Type
44A
44-lead, Thin (1.0mm) Plastic Gull Wing Quad Flat Package (TQFP)
40P6
40-pin, 0.600” Wide, Plastic Dual Inline Package (PDIP)
44M1
44-pad, 7 × 7 × 1.0mm body, lead pitch 0.50mm, Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF)
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
23
9.8
Atmel ATmega1284P
Speed [MHz] (3)
20
Notes:
Power supply
1.8 - 5.5V
Ordering code (2)
Package (1)
ATmega1284P-AU
ATmega1284P-AUR(4)
ATmega1284P-PU
ATmega1284P-MU
ATmega1284P-MUR(4)
44A
44A
40P6
44M1
44M1
Operational range
Industrial
(-40oC to 85oC)
1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering
information and minimum quantities.
2. Pb-free packaging, complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also
Halide free and fully Green.
3. For Speed vs. VCC see ”Speed grades” on page 324.
4. Tape & Reel.
Package Type
44A
44-lead, Thin (1.0mm) Plastic Gull Wing Quad Flat Package (TQFP)
40P6
40-pin, 0.600” Wide, Plastic Dual Inline Package (PDIP)
44M1
44-pad, 7 × 7 × 1.0mm body, lead pitch 0.50mm, Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF)
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
24
10.
Packaging information
10.1
44A
PIN 1 IDENTIFIER
PIN 1
e
B
E1
E
D1
D
C
0°~7°
A1
A2
A
L
COMMON DIMENSIONS
(Unit of Measure = mm)
Notes:
1. This package conforms to JEDEC reference MS-026, Variation ACB.
2. Dimensions D1 and E1 do not include mold protrusion. Allowable
protrusion is 0.25mm per side. Dimensions D1 and E1 are maximum
plastic body size dimensions including mold mismatch.
3. Lead coplanarity is 0.10mm maximum.
SYMBOL
MIN
NOM
MAX
A
–
–
1.20
A1
0.05
–
0.15
A2
0.95
1.00
1.05
D
11.75
12.00
12.25
D1
9.90
10.00
10.10
E
11.75
12.00
12.25
E1
9.90
10.00
10.10
B
0.30
0.37
0.45
C
0.09
(0.17)
0.20
L
0.45
0.60
0.75
e
NOTE
Note 2
Note 2
0.80 TYP
06/02/2014
44A, 44-lead, 10 x 10mm body size, 1.0mm body thickness,
0.8 mm lead pitch, thin profile plastic quad flat package (TQFP)
44A
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
C
25
10.2
40P6
D
PIN
1
E1
A
SEATING PLANE
A1
L
B
B1
e
E
0º ~ 15º
C
COMMON DIMENSIONS
(Unit of Measure = mm)
REF
eB
SYMBOL
MIN
NOM
MAX
A
–
–
4.826
A1
0.381
–
–
D
52.070
–
52.578
E
15.240
–
15.875
E1
13.462
–
13.970
0.356
–
0.559
B
Notes:
1. This package conforms to JEDEC reference MS-011, Variation AC.
2. Dimensions D and E1 do not include mold Flash or Protrusion.
Mold Flash or Protrusion shall not exceed 0.25mm (0.010").
B1
1.041
–
1.651
L
3.048
–
3.556
C
0.203
–
0.381
eB
15.494
–
17.526
e
NOTE
Note 2
Note 2
2.540 TYP
13/02/2014
40P6, 40-lead (0.600"/15.24mm Wide) Plastic Dual
Inline Package (PDIP)
40P6
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
C
26
10.3
44M1
C
Pin 1 ID
D
SIDE VIEW
y
A1
E
A
TOP VIEW
eT/2
A19
eR
A24
B20
B16
A1
A18
COMMON DIMENSIONS
(Unit of Measure = mm)
B1
B15
b
R0.20
MIN
NOM
MAX
A
0.80
0.90
1.00
A1
0.00
0.02
0.05
b
0.18
0.23
0.30
SYMBOL
0.40
D2
eT
C
B5
B11
A6
A13
B10
B6
A12
L
0.20 REF
D
4.90
5.00
5.10
D2
2.55
2.60
2.65
E
4.90
5.00
5.10
E2
2.55
2.60
2.65
eT
–
0.70
–
eR
–
0.40
–
K
0.45
–
–
L
0.30
0.35
0.40
y
0.00
–
0.075
A7
E2
BOTTOM VIEW
Note:
NOT E
1. The terminal #1 ID is a Laser-marked Feature.
L
L
TITLE
44MC, 44QFN (2-Row Staggered), 5 x 5 x 1.00 mm Body,
Package Drawing Contact:
[email protected] 2.60 x 2.60 mm Exposed Pad, Quad Flat No Lead Package
9/13/07
DRA WING NO . REV .
44MC
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
A
27
10.4
44MC
C
Pin 1 ID
D
SIDE VIEW
y
A1
E
A
TOP VIEW
eT/2
A19
eR
A24
B20
B16
A1
A18
COMMON DIMENSIONS
(Unit of Measure = mm)
B1
B15
b
R0.20
MIN
NOM
MAX
A
0.80
0.90
1.00
A1
0.00
0.02
0.05
b
0.18
0.23
0.30
SYMBOL
0.40
D2
eT
C
B5
B11
A6
A13
B10
B6
A12
L
0.20 REF
D
4.90
5.00
5.10
D2
2.55
2.60
2.65
E
4.90
5.00
5.10
E2
2.55
2.60
2.65
eT
–
0.70
–
eR
–
0.40
–
K
0.45
–
–
L
0.30
0.35
0.40
y
0.00
–
0.075
A7
E2
BOTTOM VIEW
Note:
NOT E
1. The terminal #1 ID is a Laser-marked Feature.
L
L
TITLE
44MC, 44QFN (2-Row Staggered), 5 x 5 x 1.00 mm Body,
Package Drawing Contact:
[email protected] 2.60 x 2.60 mm Exposed Pad, Quad Flat No Lead Package
9/13/07
DRA WING NO . REV .
44MC
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
A
28
10.5
49C2
E
A1 BALL ID
0.10
D
A1
TOP VIEW
A
A2
SIDE VIEW
E1
G
e
F
E
D
D1
COMMON DIMENSIONS
(Unit of Measure = mm)
C
B
1
A1 BALL CORNER
MIN
NOM
MAX
A
–
–
1.00
A1
0.20
–
–
A2
0.65
–
–
D
4.90
5.00
5.10
SYMBOL
A
2
3
4
5
b
6
7
e
49 - Ø0.35 ±0.05
BOTTOM VIEW
D1
E 4.90
3.90 BSC
5.00
5.10
E1
b
NOTE
3.90 BSC
0.30
0.35
e
0.40
0.65 BSC
3/14/08
TITLE
49C2, 49-ball (7 x 7 array), 0.65mm pitch,
Package Drawing Contact:
[email protected] 5.0 x 5.0 x 1.0mm, very thin, fine-pitch
ball grid array package (VFBGA)
GPC
DRAWING NO.
CBD
49C2
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
REV.
A
29
11.
Errata
11.1
Errata for ATmega164A
11.1.1 Rev. E
No known Errata.
11.2
Errata for ATmega164PA
11.2.1 Rev. E
No known Errata.
11.3
Errata for ATmega324A
11.3.1 Rev. F
No known Errata.
11.4
Errata for ATmega324PA
11.4.1 Rev. F
No known Errata.
11.5
Errata for ATmega644A
11.5.1 Rev. F
No known Errata.
11.6
Errata for ATmega644PA
11.6.1 Rev. F
No known Errata.
11.7
Errata for ATmega1284
11.7.1 Rev. B
No known Errata.
11.8
Errata for ATmega1284P
11.8.1 Rev. B
No known Errata.
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
30
12.
Datasheet revision history
Please note that the referring page numbers in this section are referred to this document. The referring revision
in this section are referring to the document revision.
12.1
12.2
Rev. 8272F - 08/2014
1.
Updated text in Section 13.2.8 ”PCMSK1 – Pin Change Mask Register 1” on page 70 to: “If
PCINT15:8 is set and the PCIE1 bit in PCICR is set, pin change interrupt is enabled on the
corresponding I/O pin.”
2.
Corrected description of PAGEMSB in Table 26-9 on page 281. The device has 64 words in a
page and not 128.
3.
Corrected description of PAGEMSB in Table 26-12 on page 282. PAGESMB is 5 and the device
has 64 words in a page and not 128. The page require six bits and not seven.
4.
Corrected values in Table 26-16 on page 284. PAGEMSB is 6. ZPAGEMSB is Z7 and PCPAGE
is Z15:Z8
5.
Corrected value for PCPAGE in Table 27-7 on page 290. The correct value is PC[14:7]
6.
Updated description in Table 17-2 on page 151 to “Normal port operation, OC2A disconnected.”
7.
Updated Assembly code examples on for ”Watchdog Timer” on page 55. and onwards
“out WDTCSR, r16” changed to “sts WDTCSR, r16”
“in r16, WDTCSR” changed to “lds r16, WDTCSR”
“idi r16, WDTCSR” changed to “lds r16, WDTCSR”
8.
Updated addresses 0x65 and 0x64 in Section 7. ”Register summary” on page 10.
9.
Removed notes 5 and 6 from Table 28-16 on page 328.
10.
Corrected values in Section 8. ”Instruction set summary” on page 14.Changed clock values for
RCALL and ICALL to 2, for Call, Ret and RETI to 4. Also changed values in Section 7.7.1
”Interrupt response time” on page 18.
11.
Updated layout, footer and back page according to template 0205/2014
Rev. 8272E - 04/2013
1.
2.
3.
4.
5.
6.
7.
Updated Figure 1-1 on page 3 and Figure 2-1 on page 6: T3 and T/C3 only available in
ATmega1284/1284P.
Updated descriptive text on page 6 to indicate that ATmega1284/1284P has four T/Cs.
Updated the Assembly code example for WDT_off (p.56) following the ej# 705736.
Added note in ”16-bit Timer/Counter1 and Timer/Counter3(1) with PWM” on page 107.
Added ”Prescaler Reset” on page 112.
Corrected three typo for Waveform generation mode (WGM) instead of MGM.
Updated Table 23-6 on page 253. ADC Auto Trigger Source Selections, ADTS=0b011, the
statement is Timer/Counter0 Compare Match A.
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
31
8.
9.
10.
12.3
Rev. 8272D - 05/12
1.
2.
3.
4.
5.
6.
12.4
Updated ”Power-down mode” on page 44.
Updated ”Overview” on page 67.
Corrected references for Bit 2, Bit 1, and Bit 0 in Section ”UCSRnC – USART MSPIM Control
and Status Register n C” on page 201.
Several small corrections throughout the whole document made according to the template
Notes in Table 27-17 on page 304 have been corrected
Note (1) in Table 28-3 on page 320 is added
Rev. 8272C - 06/11
1.
12.5
Updated Table 27-18 on page 310. Command for 6d Poll for Fuse Write Complete:
0111011_00000000
Updated the table notes of the Table 28-1 on page 318.
Updated ”Register summary” on page 10. Added table note 7: Only available in
ATmega1284/1284P.
Updated ”Atmel ATmega1284P DC characteristics” on page 323.
Rev. 8272B - 05/11
1.
2.
3.
4.
5.
6.
Added Atmel QTouch Library Support and QTouch Sensing Capability Features.
Replaced the Figure 1-1 on page 3 by an updated “Pinout.” that includes Timer/Counter3.
Replaced the Figure 7-1 on page 10 by an updated “Block diagram of the AVR architecture.” that
includes Timer/Counter3.
Added ”RAMPZ – Extended Z-pointer Register for ELPM/SPM(1)” on page 15.
Added ”PRR1 – Power Reduction Register 1” on page 49.
Renamed PRR to ”PRR0 – Power Reduction Register 0” on page 48.
7.
Updated ”PCIFR – Pin Change Interrupt Flag Register” on page 69. PCICR replaces EIMSR in
the PCIF3, PCIF2, PCIF1 and PCIF0 bit description.
8.
Updated ”PCMSK3 – Pin Change Mask Register 3” on page 70. PCIE3 replaces PCIE2 in the bit
description.
9.
Updated ”Alternate Functions of Port B” on page 80 to include Timer/Counter3
10.
Updated ”Alternate Functions of Port D” on page 86 to include Timer/Counter3
11.
Added ”TCNT3H and TCNT3L –Timer/Counter3” on page 132
12.
Added ”OCR3AH and OCR3AL – Output Compare Register3 A” on page 133
13.
Added ”OCR3BH and OCR3BL – Output Compare Register3 B” on page 133
14.
Added ”TIMSK3 – Timer/Counter3 Interrupt Mask Register” on page 134
15.
Updated All “SPI – Serial Peripheral Interface” “Register description” to reflect ATmega1284 and
ATmega1284P.
16.
Updated ”Addressing the Flash During Self-Programming” on page 274 to include RAMPZ
register.
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
32
12.6
17.
Updated Table 27-16 on page 303. tWD_EEPROM is 3.6ms instead of 9ms.
18.
BODS and BODSE bits denoted as R/W
19.
Description of external pin modes below table 16-9 removed.
20.
Updated ”Register summary” on page 10 to include Timer/Counter3.
21.
Updated the datasheet with Atmel new style guide.
Rev. 8272A - 01/10
1.
Initial revision (Based on the ATmega164PA/324PA/644PA/1284P datasheet 8252G-AVR-11/09
and on the ATmega644 datasheet 2593N-AVR-09/09).
2.
Changes done:
̶
Non-picoPower devices added: ATmega164A/324A/644A/1284
̶
Updated Table 2-1 on page 7
̶
Updated Table 10-1 on page 42
̶
Updated ”Sleep Modes” on page 42 and ”BOD disable(1)” on page 43
̶
Updated ”Register description” on page 67
̶
Updated ”USART” on page 167 and ”USART in SPI mode” on page 194
̶
Updated ”Signature Bytes” on page 290 and ”Page Size” on page 290
̶
Added ”DC Characteristics” on page 318 for non-picoPower devices.
̶
Added ”Atmel ATmega164A typical characteristics” on page 333
̶
Added ”Atmel ATmega324A typical characteristics” on page 386
̶
Added ”Atmel ATmega644A typical characteristics” on page 438
̶
Added ”ATmega1284 typical characteristics” on page 490
̶
Added ”Ordering information” on page 17 for non-picoPower devices
̶
Added ”Errata for ATmega164A” on page 30
̶
Added ”Errata for ATmega324A” on page 30
̶
Added ”Errata for ATmega644PA” on page 30
̶
Added ”Errata for ATmega1284” on page 30
ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P [DATASHEET SUMMARY]
Atmel-8272FS-AVR--07/2014
33
XXXXXX
Atmel Corporation
1600 Technology Drive, San Jose, CA 95110 USA
T: (+1)(408) 441.0311
F: (+1)(408) 436.4200
|
www.atmel.com
© 2014 Atmel Corporation. / Rev.: Atmel-8272FS-AVR-ATmega164A/PA/324A/PA/644A/PA/1284/P-Datasheet Summary_07/2014.
Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities, and others are registered trademarks or trademarks of Atmel Corporation in U.S. and
other countries. Other terms and product names may be trademarks of others.
DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right
is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE
ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT
SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES
FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this
document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information
contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended,
authorized, or warranted for use as components in applications intended to support or sustain life.
SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where
the failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical Applications”) without an Atmel officer's specific written
consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for the operation of nuclear facilities and weapons systems.
Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are
not designed nor intended for use in automotive applications unless specifically designated by Atmel as automotive-grade.
Similar pages