Document 418-1 SMT Power Magnetics For ON Semiconductor NCP1216A Controller Coilcraft’s C0972-AL transformer and B0754-AL inductor were developed specifically for the ON Semiconductor NCP1216A PWM Current-Mode Controller. They are specified in application note AND8161/D along with Coilcraft’s DS3316P-103 and DS3316P-102 shielded inductors. Refer to the separate data sheet for additional information about the DS3316 Series of inductors The C0972-AL features very low DCR, excellent leakage inductance and 1500 V Isolation from the primary and auxiliary windings to the secondary. The B0754-AL is the output inductor and features four separate windings connected in parallel to minimize power losses and to limit temperature rise. To request free evaluation samples, contact Coilcraft or visit www.coilcraft.com. C0972-AL Transformer Part number C0972-AL Output power (W) 60 Input voltage range (V) 36 – 75 Output voltage (V) 12 Output current (A rms) 5.0 Primary inductance1 min (mH) 0.817 2. Inductance measured between pins 2 and 4 at 10 kHz, 0.1 V, 0 Adc. 3. Leakage inductance measured between pins 2 and 4 at 100 kHz, 0.1 V, 0 Adc with all other pins shorted. 4. Operating temperature range: –40°C to +85°C. 5. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Leakage inductance2 max (µH) 1.50 2 Primary 4 0.560 max 14,22 0.004 /0,10 0.043 1,10 1.024 26,00 6 5 10 Recommended Land Pattern Secondary 6 10 1 1.280 max 32,51 0.079 2,00 1.10 27,94 5 Reset Turns ratio pri : sec pri: reset 1 : 0.91 1:1 Dot above pin1 0.035 0,90 0.108 2,74 DCR max (Ohms) 0.056 (pri) 0.031 (sec) 0.480 (aux) 1.060 max 26,92 1 0.196 4,98 10 1 Bottom View 0.196 4,98 Document 418-1 Revised 01/23/09 Weight: 28.2 g Terminations: Tin-silver over tin over nickel over phos bronze Packaging: 24 per tray Specifications subject to change without notice. Please check our website for latest information. © Coilcraft, Inc. 2009 Document 418-2 SMT Power Magnetics for ON Semiconductor NCP1216A B0754-AL Inductor Part number B0754-AL Inductance1 at 0 A ±10% (µH) 100 Dot above pin1 Isat3 (A) 8.0 DCR max2 (Ohms) 0.282 Irms4 (A) 4.8 1. Inductance measured at 10.0 kHz, 0.1 Vrms. 2. DCR is per winding. 3. Current at which inductance drops 10% (typ) from its value without current. 4. Average current for a 40°C temperature rise above 25°C ambient. 5. Operating temperature range −40°C to +85°C. 6. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. 0.545 max 13,84 0.004 /0,10 0.035 0,90 1.280 max 32,51 0.043 1,10 1.024 26,00 6 5 1.060 max 26,92 1 10 Typical L vs Frequency Bottom View 0.079 2,00 Inductance (µH) 1000 4 3 2 1 Recommended Land Pattern 100 0.196 10 4,98 0.108 2,74 10 1 0.01 1 0.1 10 Frequency (MHz) Typical L vs Current 10 9 8 7 1 1.10 27,94 Windings to be connected in parallel on the PC board Weight: 27.4 g Terminations: Tin-silver over tin over nickel over phos bronze Packaging: 24 per tray Temperature Rise vs Current 1000 70 Temperature rise (from 25°C) Inductance (µH) 0.196 4,98 100 10 1 60 50 40 30 20 10 0 0.1 10 1 100 0 1 2 Current (A) Specifications subject to change without notice. Please check our website for latest information. © Coilcraft, Inc. 2009 3 4 5 6 7 Current (A) Document 418-2 Revised 01/23/09