IC41C16100S IC41LV16100S Document Title 1M x 16 bits Dynamic RAM with EDO Page Mode Revision History Revision No History Draft Date 0A 0B 0C 0D Initial Draft Revise for typographic Add Pb-free package Change tCOH from 5ns to 4ns June 5,2001 November 9,2001 May 06,2004 November 26,2004 Remark The attached datasheets are provided by ICSI. Integrated Circuit Solution Inc reserve the right to change the specifications and products. ICSI will answer to your questions about device. If you have any questions, please contact the ICSI offices. Integrated Circuit Solution Inc. DR010-0D 11/26/2004 1 IC41C16100S IC41LV16100S 1M x 16 (16-MBIT) DYNAMIC RAM WITH EDO PAGE MODE DESCRIPTION The ICSI IC41C16100S and IC41LV16100S are 1,048,576 x FEATURES • Extended Data-Out (EDO) Page Mode access cycle • TTL compatible inputs and outputs; tristate I/O • Refresh Interval: Refresh Mode: 1,024 cycles /16 ms RAS-Only, CAS-before-RAS (CBR), and Hidden Self refresh Mode - 1,024 cycles / 128ms • JEDEC standard pinout • Single power supply: 5V ± 10% (IC41C16100S) 3.3V ± 10% (IC41LV16100S) • Byte Write and Byte Read operation via two CAS 16-bit high-performance CMOS Dynamic Random Access Memories. These devices offer an accelerated cycle access called EDO Page Mode. EDO Page Mode allows 1,024 random accesses within a single row with access cycle time as short as 20 ns per 16-bit word. The Byte Write control, of upper and lower byte, makes the IC41C16100S ideal for use in 16-, 32-bit wide data bus systems. These features make the IC41C16100Sand IC41LV16100S ideally suited for high-bandwidth graphics, digital signal processing, high-performance computing systems, and peripheral applications. • Industrail Temperature Range -40°C to 85°C The IC41C16100S and IC41LV16100S are packaged in a 42-pin 400mil SOJ and 400mil 50- (44-) pin TSOP-2. KEY TIMING PARAMETERS Parameter -45 -50 -60 Unit Max. RAS Access Time (tRAC) 45 50 60 ns Max. CAS Access Time (tCAC) 11 13 15 ns Max. Column Address Access Time (tAA) 22 25 30 ns Min. EDO Page Mode Cycle Time (tPC) 16 20 25 ns Min. Read/Write Cycle Time (tRC) 77 84 104 ns PIN CONFIGURATIONS 50(44)-Pin TSOP II 42-Pin SOJ PIN DESCRIPTIONS VCC 1 42 GND A0-A9 Address Inputs I/O0 2 41 I/O15 I/O0-15 Data Inputs/Outputs I/O1 3 40 I/O14 I/O2 4 39 I/O13 WE Write Enable I/O3 5 38 I/O12 OE Output Enable I/O11 VCC 6 37 GND 43 I/O10 I/O4 7 36 I/O11 RAS Row Address Strobe 42 I/O9 I/O5 8 35 I/O10 I/O8 9 34 I/O9 Upper Column Address Strobe 41 I/O6 UCAS 10 11 40 NC I/O7 10 33 I/O8 LCAS Lower Column Address Strobe NC 11 32 NC NC 12 31 LCAS Vcc Power VCC 1 50 GND I/O0 2 49 I/O15 I/O1 3 48 I/O14 I/O2 4 47 I/O13 I/O3 5 46 I/O12 VCC 6 45 GND I/O4 7 44 I/O5 8 I/O6 9 I/O7 NC NC 15 36 NC NC 16 35 LCAS WE 13 30 UCAS GND Ground WE 17 34 UCAS RAS 14 29 OE RAS 18 33 OE NC 15 28 A9 NC No Connection NC 19 32 A9 NC 16 27 A8 NC 20 31 A8 A0 21 30 A7 A0 17 26 A7 A1 22 29 A6 A1 18 25 A6 A2 23 28 A5 A2 19 24 A5 A3 24 27 A4 A3 20 23 A4 VCC 25 26 GND VCC 21 22 GND ICSI reserves the right to make changes to its products at any time without notice in order to improve design and supply the best possible product. We assume no responsibility for any errors which may appear in this publication. © Copyright 2000, Integrated Circuit Solution Inc. 2 Integrated Circuit Solution Inc. DR010-0D 11/26/2004 IC41C16100S IC41LV16100S FUNCTIONAL BLOCK DIAGRAM OE WE LCAS UCAS CAS CLOCK GENERATOR WE CONTROL LOGICS CAS WE OE CONTROL LOGIC OE DATA I/O BUS COLUMN DECODERS SENSE AMPLIFIERS ADDRESS BUFFERS A0-A9 Integrated Circuit Solution Inc. DR010-0D 11/26/2004 ROW DECODER REFRESH COUNTER MEMORY ARRAY 1,048,576 x 16 DATA I/O BUFFERS RAS CLOCK GENERATOR RAS RAS I/O0-I/O15 3 IC41C16100S IC41LV16100S TRUTH TABLE Standby Read: Word Read: Lower Byte RAS H L L Read: Upper Byte L H L H L ROW/COL Write: Word (Early Write) Write: Lower Byte (Early Write) L L L L L H L L X X ROW/COL ROW/COL Write: Upper Byte (Early Write) L H L L X ROW/COL L H→L H→L L→H H→L H→L H→L H→L L L H L L H→L H→L L→H H→L H→L H→L H→L L L H L H→L H H H L L H→L H→L H L X X L→H L L L X X L→H L→H L X X X ROW/COL ROW/COL NA/COL NA/NA ROW/COL NA/COL ROW/COL NA/COL ROW/COL ROW/COL ROW/NA X Function Read-Write(1,2) EDO Page-Mode Read(2) EDO Page-Mode Write(1) EDO Page-Mode(1,2) Read-Write Hidden Refresh RAS-Only Refresh CBR Refresh(4) L 1st Cycle: L 2nd Cycle: L Any Cycle: L 1st Cycle: L 2nd Cycle: L 1st Cycle: L 2nd Cycle: L Read(2) L→H→L Write(1,3) L→H→L L H→L LCAS UCAS H H L L L H WE X H H OE X L L Address tR/tC X ROW/COL ROW/COL I/O High-Z DOUT Lower Byte, DOUT Upper Byte, High-Z Lower Byte, High-Z Upper Byte, DOUT DIN Lower Byte, DIN Upper Byte, High-Z Lower Byte, High-Z Upper Byte, DIN DOUT, DIN DOUT DOUT DOUT DIN DIN DOUT, DIN DOUT, DIN DOUT DOUT High-Z High-Z Notes: 1. These WRITE cycles may also be BYTE WRITE cycles (either LCAS or UCAS active). 2. These READ cycles may also be BYTE READ cycles (either LCAS or UCAS active). 3. EARLY WRITE only. 4. At least one of the two CAS signals must be active (LCAS or UCAS). 4 Integrated Circuit Solution Inc. DR010-0D 11/26/2004 IC41C16100S IC41LV16100S Functional Description The IC41C16100S and IC41LV16100S is a CMOS DRAM optimized for high-speed bandwidth, low power applications. During READ or WRITE cycles, each bit is uniquely addressed through the 16 address bits. These are entered ten bits (A0-A9) at a time. The row address is latched by the Row Address Strobe (RAS). The column address is latched by the Column Address Strobe (CAS). RAS is used to latch the first ten bits and CAS is used the latter ten bits. The IC41C16100S and IC41LV16100S has two CAS controls, LCAS and UCAS. The LCAS and UCAS inputs internally generates a CAS signal functioning in an identical manner to the single CAS input on the other 1M x 16 DRAMs. The key difference is that each CAS controls its corresponding I/O tristate logic (in conjunction with OE and WE and RAS). LCAS controls I/O0 through I/O7 and UCAS controls I/O8 through I/O15. The IC41C16100S and IC41LV16100S CAS function is determined by the first CAS (LCAS or UCAS) transitioning LOW and the last transitioning back HIGH. The two CAS controls give the IC41C16100S and IS41LV16100S both BYTE READ and BYTE WRITE cycle capabilities. Memory Cycle A memory cycle is initiated by bring RAS LOW and it is terminated by returning both RAS and CAS HIGH. To ensures proper device operation and data integrity any memory cycle, once initiated, must not be ended or aborted before the minimum tRAS time has expired. A new cycle must not be initiated until the minimum precharge time tRP, tCP has elapsed. Read Cycle A read cycle is initiated by the falling edge of CAS or OE, whichever occurs last, while holding WE HIGH. The column address must be held for a minimum time specified by tAR. Data Out becomes valid only when tRAC, tAA, tCAC and tOEA are all satisfied. As a result, the access time is dependent on the timing relationships between these parameters. Write Cycle A write cycle is initiated by the falling edge of CAS and WE, whichever occurs last. The input data must be valid at or before the falling edge of CAS or WE, whichever occurs first. Refresh Cycle To retain data, 1,024 refresh cycles are required in each 16 ms period. There are two ways to refresh the memory. 1. By clocking each of the 1,024 row addresses (A0 through A9) with RAS at least once every 16 ms. Any read, write, read-modify-write or RAS-only cycle refreshes the addressed row. 2. Using a CAS-before-RAS refresh cycle. CAS-beforeRAS refresh is activated by the falling edge of RAS, while holding CAS LOW. In CAS-before-RAS refresh cycle, an internal 10-bit counter provides the row Integrated Circuit Solution Inc. DR010-0D 11/26/2004 addresses and the external address inputs are ignored. CAS-before-RAS is a refresh-only mode and no data access or device selection is allowed. Thus, the output remains in the High-Z state during the cycle. Self Refresh Cycle The Self Refresh allows the user a dynamic refresh, data retention mode at the extended refresh period of 128 ms. i.e., 125 µs per row when using distributed CBR refreshes. The feature also allows the user the choice of a fully static, low power data retention mode. The optional Self Refresh feature is initiated by performing a CBR Refresh cycle and holding RAS LOW for the specified tRAS. The Self Refresh mode is terminated by driving RAS HIGH for a minimum time of t RP . This delay allows for the completion of any internal refresh cycles that may be in process at the time of the RAS LOW-to-HIGH transition. If the DRAM controller uses a distributed refresh sequence, a burst refresh is not required upon exiting Self Refresh. However, if the DRAM controller utilizes a RAS-only or burst refresh sequence, all 1,024 rows must be refreshed within the average internal refresh rate, prior to the resumption of normal operation. Extended Data Out Page Mode EDO page mode operation permits all 1,024 columns within a selected row to be randomly accessed at a high data rate. In EDO page mode read cycle, the data-out is held to the next CAS cycle’s falling edge, instead of the rising edge. For this reason, the valid data output time in EDO page mode is extended compared with the fast page mode. In the fast page mode, the valid data output time becomes shorter as the CAS cycle time becomes shorter. Therefore, in EDO page mode, the timing margin in read cycle is larger than that of the fast page mode even if the CAS cycle time becomes shorter. In EDO page mode, due to the extended data function, the CAS cycle time can be shorter than in the fast page mode if the timing margin is the same. The EDO page mode allows both read and write operations during one RAS cycle, but the performance is equivalent to that of the fast page mode in that case. Power-On After application of the VCC supply, an initial pause of 200 µs is required followed by a minimum of eight initialization cycles (any combination of cycles containing a RAS signal). During power-on, it is recommended that RAS track with VCC or be held at a valid VIH to avoid current surges. 5 IC41C16100S IC41LV16100S ABSOLUTE MAXIMUM RATINGS(1) Symbol Parameters VT Voltage on Any Pin Relative to GND VCC Supply Voltage IOUT PD TA Output Current Power Dissipation Commercial Operation Temperature Industrial Operationg Temperature Storage Temperature TSTG 5V 3.3V 5V 3.3V Rating Unit –1.0 to +7.0 –0.5 to +4.6 –1.0 to +7.0 –0.5 to +4.6 50 1 0 to +70 –40 to +85 –55 to +125 V V mA W °C °C °C Note: 1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. RECOMMENDED OPERATING CONDITIONS (Voltages are referenced to GND.) Symbol Parameter VCC Supply Voltage VIH Input High Voltage VIL Input Low Voltage TA Commercial Ambient Temperature Industrial Ambient Temperature 5V 3.3V 5V 3.3V 5V 3.3V Min. Typ. Max. Unit 4.5 3.0 2.4 2.0 –1.0 –0.3 0 –40 5.0 3.3 — — — — — — 5.5 3.6 VCC + 1.0 VCC + 0.3 0.8 0.8 70 85 V V V °C °C CAPACITANCE(1,2) Symbol Parameter CIN1 CIN2 CIO Input Capacitance: A0-A9 Input Capacitance: RAS, UCAS, LCAS, WE, OE Data Input/Output Capacitance: I/O0-I/O15 Max. Unit 5 7 7 pF pF pF Notes: 1. Tested initially and after any design or process changes that may affect these parameters. 2. Test conditions: TA = 25°C, f = 1 MHz. 6 Integrated Circuit Solution Inc. DR010-0D 11/26/2004 IC41C16100S IC41LV16100S ELECTRICAL CHARACTERISTICS(1) (Recommended Operating Conditions unless otherwise noted.) Symbol Parameter Test Condition IIL Input Leakage Current IIO Speed Min. Max. Unit Any input 0V ≤ VIN ≤ Vcc Other inputs not under test = 0V –5 5 µA Output Leakage Current Output is disabled (Hi-Z) 0V ≤ VOUT ≤ Vcc –5 5 µA VOH Output High Voltage Level IOH = –5.0 mA (5V) IOH = –2.0 mA (3.3V) 2.4 — V VOL Output Low Voltage Level IOL = 4.2 mA (5V) IOL = 2.0 mA (3.3V) — 0.4 V ICC1 Standby Current: TTL RAS, LCAS, UCAS ≥ VIH Commerical 5V 3.3V 5V 3.3V — — — — 2 1 3 2 mA Extended mA ICC2 Standby Current: CMOS RAS, LCAS, UCAS ≥ VCC – 0.2V 5V 3.3V — — 1 0.5 mA ICC3 Operating Current: RAS, LCAS, UCAS, Random Read/Write(2,3,4) Address Cycling, tRC = tRC (min.) Average Power Supply Current -45 -50 -60 — — — 190 160 145 mA ICC4 Operating Current: RAS = VIL, LCAS, UCAS, EDO Page Mode(2,3,4) Cycling tPC = tPC (min.) Average Power Supply Current -45 -50 -60 — — — 100 90 80 mA ICC5 Refresh Current: RAS Cycling, LCAS, UCAS ≥ VIH RAS-Only(2,3) tRC = tRC (min.) Average Power Supply Current -45 -50 -60 — — — 180 160 145 mA ICC6 Refresh Current: CBR(2,3,5) Average Power Supply Current RAS, LCAS, UCAS Cycling tRC = tRC (min.) -45 -50 -60 — — — 180 160 145 mA ICCS Self Refresh Current Self Refresh mode — — 300 µA Notes: 1. An initial pause of 200 µs is required after power-up followed by eight RAS refresh cycles (RAS-Only or CBR) before proper device operation is assured. The eight RAS cycles wake-up should be repeated any time the tREF refresh requirement is exceeded. 2. Dependent on cycle rates. 3. Specified values are obtained with minimum cycle time and the output open. 4. Column-address is changed once each EDO page cycle. 5. Enables on-chip refresh and address counters. Integrated Circuit Solution Inc. DR010-0D 11/26/2004 7 IC41C16100S IC41LV16100S AC CHARACTERISTICS(1,2,3,4,5,6) (Recommended Operating Conditions unless otherwise noted.) Symbol Parameter tRC tRAC tCAC tAA tRAS tRP tCAS tCP tCSH tRCD tASR tRAH tASC tCAH tAR Random READ or WRITE Cycle Time Access Time from RAS(6, 7) Access Time from CAS(6, 8, 15) Access Time from Column-Address(6) RAS Pulse Width RAS Precharge Time CAS Pulse Width(26) CAS Precharge Time(9, 25) CAS Hold Time (21) RAS to CAS Delay Time(10, 20) Row-Address Setup Time Row-Address Hold Time Column-Address Setup Time(20) Column-Address Hold Time(20) Column-Address Hold Time (referenced to RAS) RAS to Column-Address Delay Time(11) Column-Address to RAS Lead Time RAS to CAS Precharge Time RAS Hold Time(27) RAS Hold Time from CAS Precharge CAS to Output in Low-Z(15, 29) CAS to RAS Precharge Time(21) Output Disable Time(19, 28, 29) Output Enable Time(15, 16) Output Enable Data Delay (Write) OE HIGH Hold Time from CAS HIGH OE HIGH Pulse Width OE LOW to CAS HIGH Setup Time Read Command Setup Time(17, 20) Read Command Hold Time (referenced to RAS)(12) Read Command Hold Time (referenced to CAS)(12, 17, 21) Write Command Hold Time(17, 27) Write Command Hold Time (referenced to RAS)(17) Write Command Pulse Width(17) WE Pulse Widths to Disable Outputs Write Command to RAS Lead Time(17) Write Command to CAS Lead Time(17, 21) Write Command Setup Time(14, 17, 20) Data-in Hold Time (referenced to RAS) tRAD tRAL tRPC tRSH tRHCP tCLZ tCRP tOD tOE tOED tOEHC tOEP tOES tRCS tRRH tRCH tWCH tWCR tWP tWPZ tRWL tCWL tWCS tDHR 8 -45 Min. Max. -50 Min. Max. -60 Min. Max. Units 77 — — — 45 28 7 7 35 10 0 6 0 6 30 — 45 11 22 10K — 10K — — 34 — — — — — 84 — — — 50 30 8 9 38 12 0 8 0 8 30 — 50 13 25 10K — 10K — — 37 — — — — — 104 — — — 60 40 10 9 40 14 0 10 0 10 40 — 60 15 30 10K — 10K — — 45 — — — — — ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns 8 23 5 6 37 0 5 3 — 20 5 10 5 0 0 23 — — — — — — 13 11 — — — — — — 10 25 5 8 37 0 5 3 — 20 5 10 5 0 0 25 — — — — — — 15 13 — — — — — — 12 30 5 10 37 0 5 3 — 20 5 10 5 0 0 30 — — — — — — 15 15 — — — — — — ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns 0 — 0 — 0 — ns 6 40 — — 8 40 — — 10 50 — — ns ns 6 10 11 6 0 39 — — — — — — 8 10 13 8 0 39 — — — — — — 10 10 15 10 0 39 — — — — — — ns ns ns ns ns ns Integrated Circuit Solution Inc. DR010-0D 11/26/2004 IC41C16100S IC41LV16100S AC CHARACTERISTICS (Continued)(1,2,3,4,5,6) (Recommended Operating Conditions unless otherwise noted.) Symbol Parameter tACH Column-Address Setup Time to CAS Precharge during WRITE Cycle OE Hold Time from WE during READ-MODIFY-WRITE cycle(18) Data-In Setup Time(15, 22) Data-In Hold Time(15, 22) READ-MODIFY-WRITE Cycle Time RAS to WE Delay Time during READ-MODIFY-WRITE Cycle(14) CAS to WE Delay Time(14, 20) Column-Address to WE Delay Time(14) EDO Page Mode READ or WRITE Cycle Time(24) RAS Pulse Width in EDO Page Mode Access Time from CAS Precharge(15) EDO Page Mode READ-WRITE Cycle Time(24) Data Output Hold after CAS LOW Output Buffer Turn-Off Delay from CAS or RAS(13,15,19, 29) Output Disable Delay from WE Last CAS going LOW to First CAS returning HIGH(23) CAS Setup Time (CBR REFRESH)(30, 20) CAS Hold Time (CBR REFRESH)(30, 21) OE Setup Time prior to RAS during HIDDEN REFRESH Cycle Auto Refresh Period (1,024 Cycles) Self Refresh Period (1,024 Cycles) Transition Time (Rise or Fall)(2, 3) tOEH tDS tDH tRWC tRWD tCWD tAWD tPC tRASP tCPA tPRWC tCOH tOFF tWHZ tCLCH tCSR tCHR tORD tREF tREF tT -45 Min. Max. -50 Min. Max. -60 Min. Max. Units 15 — 15 — 15 — ns 6 — 8 — 10 — ns 0 6 95 55 — — — — 0 8 108 64 — — — — 0 10 133 77 — — — — ns ns ns ns 21 32 16 — — — 26 39 20 — — — 32 47 25 — — — ns ns ns 45 — 51 100K 27 — 50 — 56 100K 30 — 60 — 68 100K 35 — ns ns ns 4 1.6 — 11 4 1.6 — 12 4 1.6 — 15 ns ns 3 8 10 — 3 10 10 — 3 10 10 — ns ns 5 8 0 — — — 5 8 0 — — — 5 10 0 — — — ns ns ns — — 1 16 128 50 — — 1 16 128 50 — — 1 16 128 50 ms ms ns AC TEST CONDITIONS Output load: Two TTL Loads and 50 pF (Vcc = 5.0V ± 10%) One TTL Load and 50 pF (Vcc = 3.3V ±10%) Input timing reference levels: VIH = 2.4V, VIL = 0.8V (Vcc = 5.0V ± 10%); VIH = 2.0V, VIL = 0.8V (Vcc = 3.3V ±10%) Output timing reference levels: VOH = 2.0V, VOL = 0.8V (Vcc = 5V ± 10%, 3.3V ± 10%) Integrated Circuit Solution Inc. DR010-0D 11/26/2004 9 IC41C16100S IC41LV16100S Notes: 1. An initial pause of 200 µs is required after power-up followed by eight RAS refresh cycle (RAS-Only or CBR) before proper device operation is assured. The eight RAS cycles wake-up should be repeated any time the tREF refresh requirement is exceeded. 2. VIH (MIN) and VIL (MAX) are reference levels for measuring timing of input signals. Transition times, are measured between VIH and VIL (or between VIL and VIH) and assume to be 1 ns for all inputs. 3. In addition to meeting the transition rate specification, all input signals must transit between VIH and VIL (or between VIL and VIH) in a monotonic manner. 4. If CAS and RAS = VIH, data output is High-Z. 5. If CAS = VIL, data output may contain data from the last valid READ cycle. 6. Measured with a load equivalent to one TTL gate and 50 pF. 7. Assumes that tRCD ≤ tRCD (MAX). If tRCD is greater than the maximum recommended value shown in this table, tRAC will increase by the amount that tRCD exceeds the value shown. 8. Assumes that tRCD ≥ tRCD (MAX). 9. If CAS is LOW at the falling edge of RAS, data out will be maintained from the previous cycle. To initiate a new cycle and clear the data output buffer, CAS and RAS must be pulsed for tCP. 10. Operation with the tRCD (MAX) limit ensures that tRAC (MAX) can be met. tRCD (MAX) is specified as a reference point only; if tRCD is greater than the specified tRCD (MAX) limit, access time is controlled exclusively by tCAC. 11. Operation within the tRAD (MAX) limit ensures that tRCD (MAX) can be met. tRAD (MAX) is specified as a reference point only; if tRAD is greater than the specified tRAD (MAX) limit, access time is controlled exclusively by tAA. 12. Either tRCH or tRRH must be satisfied for a READ cycle. 13. tOFF (MAX) defines the time at which the output achieves the open circuit condition; it is not a reference to VOH or VOL. 14. tWCS, tRWD, tAWD and tCWD are restrictive operating parameters in LATE WRITE and READ-MODIFY-WRITE cycle only. If tWCS ≥ tWCS (MIN), the cycle is an EARLY WRITE cycle and the data output will remain open circuit throughout the entire cycle. If tRWD ≥ tRWD (MIN), tAWD ≥ tAWD (MIN) and tCWD ≥ tCWD (MIN), the cycle is a READ-WRITE cycle and the data output will contain data read from the selected cell. If neither of the above conditions is met, the state of I/O (at access time and until CAS and RAS or OE go back to VIH) is indeterminate. OE held HIGH and WE taken LOW after CAS goes LOW result in a LATE WRITE (OE-controlled) cycle. 15. Output parameter (I/O) is referenced to corresponding CAS input, I/O0-I/O7 by LCAS and I/O8-I/O15 by UCAS. 16. During a READ cycle, if OE is LOW then taken HIGH before CAS goes HIGH, I/O goes open. If OE is tied permanently LOW, a LATE WRITE or READ-MODIFY-WRITE is not possible. 17. Write command is defined as WE going low. 18. LATE WRITE and READ-MODIFY-WRITE cycles must have both tOD and tOEH met (OE HIGH during WRITE cycle) in order to ensure that the output buffers will be open during the WRITE cycle. The I/Os will provide the previously written data if CAS remains LOW and OE is taken back to LOW after tOEH is met. 19. The I/Os are in open during READ cycles once tOD or tOFF occur. 20. The first χCAS edge to transition LOW. 21. The last χCAS edge to transition HIGH. 22. These parameters are referenced to CAS leading edge in EARLY WRITE cycles and WE leading edge in LATE WRITE or READMODIFY-WRITE cycles. 23. Last falling χCAS edge to first rising χCAS edge. 24. Last rising χCAS edge to next cycle’s last rising χCAS edge. 25. Last rising χCAS edge to first falling χCAS edge. 26. Each χCAS must meet minimum pulse width. 27. Last χCAS to go LOW. 28. I/Os controlled, regardless UCAS and LCAS. 29. The 3 ns minimum is a parameter guaranteed by design. 30. Enables on-chip refresh and address counters. 10 Integrated Circuit Solution Inc. DR010-0D 11/26/2004 IC41C16100S IC41LV16100S READ CYCLE tRC tRAS tRP RAS tCSH tCRP tRSH tCAS tCLCH tRCD tRRH UCAS/LCAS tAR tRAD tASR ADDRESS tRAH tRAL tCAH tASC Row Column Row tRCS tRCH WE tAA tRAC tCAC tCLC I/O tOFF(1) Open Open Valid Data tOE tOD OE tOES Undefined Don’t Care Note: 1. tOFF is referenced from rising edge of RAS or CAS, whichever occurs last. Integrated Circuit Solution Inc. DR010-0D 11/26/2004 11 IC41C16100S IC41LV16100S EARLY WRITE CYCLE (OE = DON'T CARE) tRC tRAS tRP RAS tCSH tCRP tRSH tCAS tCLCH tRCD UCAS/LCAS tAR tRAD tRAH tASR ADDRESS tRAL tCAH tACH tASC Row Column Row tCWL tRWL tWCR tWCS tWCH tWP WE tDHR tDS I/O tDH Valid Data Don’t Care 12 Integrated Circuit Solution Inc. DR010-0D 11/26/2004 IC41C16100S IC41LV16100S READ WRITE CYCLE (LATE WRITE and READ-MODIFY-WRITE Cycles) tRWC tRAS tRP RAS tCSH tCRP tRSH tCAS tCLCH tRCD UCAS/LCAS tAR tRAD tRAH tASR tRAL tCAH tASC tACH ADDRESS Row Column Row tRWD tCWL tRWL tCWD tRCS tAWD tWP WE tAA tRAC tCAC tCLZ I/O tDS Open Valid DOUT tOE tDH Valid DIN tOD Open tOEH OE Undefined Don’t Care Integrated Circuit Solution Inc. DR010-0D 11/26/2004 13 IC41C16100S IC41LV16100S EDO-PAGE-MODE READ CYCLE tRASP tRP RAS tCSH tCRP tCAS, tCLCH tRCD tCP tPC(1) tCAS, tCLCH tRSH tCAS, tCLCH tCP tCP UCAS/LCAS tAR tRAD tASR ADDRESS tASC tCAH tASC Row Column tRAL tCAH tCAH tASC Column Column Row tRAH tRRH tRCS tRCH WE tAA tRAC tCAC tCLZ I/O Open tAA tCPA tCAC tCOH Valid Data tOE tOES tAA tCPA tCAC tCLZ tOFF Valid Data tOEHC Valid Data Open tOE tOD tOES tOD OE tOEP Undefined Don’t Care Note: 1. tPC can be measured from falling edge of CAS to falling edge of CAS, or from rising edge of CAS to rising edge of CAS. Both measurements must meet the tPC specifications. 14 Integrated Circuit Solution Inc. DR010-0D 11/26/2004 IC41C16100S IC41LV16100S EDO-PAGE-MODE EARLY-WRITE CYCLE tRASP tRP tRHCP RAS tCSH tCRP tPC tCAS, tCLCH tRCD tCP tCAS, tCLCH tCP tRSH tCAS, tCLCH tCP UCAS/LCAS tAR tACH tCAH tASC tRAD tASR ADDRESS tASC Row Column tRAH tACH tRAL tCAH tACH tCAH tASC Column tCWL tWCS Column tCWL tWCS tWCH tCWL tWCS tWCH tWCH tWP tWP Row tWP WE tWCR tDHR tRWL tDS tDS tDH I/O Valid Data tDS tDH Valid Data tDH Valid Data OE Don’t Care Integrated Circuit Solution Inc. DR010-0D 11/26/2004 15 IC41C16100S IC41LV16100S EDO-PAGE-MODE READ-WRITE CYCLE (LATE WRITE and READ-MODIFY WRITE Cycles) tRASP tRP RAS tCSH tCRP tCAS, tCLCH tRCD tCP tPC / tPRWC(1) tCAS, tCLCH tRSH tCAS, tCLCH tCP tCP UCAS/LCAS tASR tRAH ADDRESS tAR tRAD tASC tCAH Row tASC tCAH Column tRWD tRCS tRAL tCAH tASC Column tCWL tWP Column tRWL tCWL tWP tCWL tWP tAWD tCWD Row tAWD tCWD tAWD tCWD WE tAA tAA tCPA tDH tDS tRAC tCAC tCLZ I/O Open tCAC tCLZ DOUT DIN DIN DOUT tOD tOE tDH tDS tCAC tCLZ DOUT tOD tOE tAA tCPA tDH tDS Open DIN tOD tOE tOEH OE Undefined Don’t Care Note: 1. tPC can be measured from falling edge of CAS to falling edge of CAS, or from rising edge of CAS to rising edge of CAS. Both measurements must meet the tPC specifications. 16 Integrated Circuit Solution Inc. DR010-0D 11/26/2004 IC41C16100S IC41LV16100S EDO-PAGE-MODE READ-EARLY-WRITE CYCLE (Psuedo READ-MODIFY WRITE) tRASP tRP RAS tCSH tPC tPC tCRP tCAS tRCD tCAS tCP tRSH tCAS tCP tCP UCAS/LCAS tASR tRAH ADDRESS tAR tRAD tASC Row tCAH tASC tCAH Column (A) tASC Column (B) tRCS tACH tRAL tCAH Column (N) Row tRCH tWCS tWCH WE tAA tRAC tCAC tCPA tCAC tAA tWHZ tCOH I/O Open Valid Data (A) tDS Valid Data (B) tDH DIN Open tOE OE Don’t Care Integrated Circuit Solution Inc. DR010-0D 11/26/2004 17 IC41C16100S IC41LV16100S AC WAVEFORMS READ CYCLE (With WE-Controlled Disable) tRASP tRP RAS tCSH tPC tPC tCRP tCAS tRCD tCAS tCP tRSH tCAS tCP tCP UCAS/LCAS tASR tRAH ADDRESS tAR tRAD tASC Row tCAH tASC tCAH Column (A) tASC Column (B) tRCS tACH tRAL tCAH Column (N) Row tRCH tWCS tWCH WE tAA tCPA tCAC tRAC tCAC tWHZ tAA tCOH Open I/O tDS Valid Data (A) Valid Data (B) tDH DIN Open tOE OE Undefined Don’t Care RAS RAS-ONLY REFRESH CYCLE (OE, WE = DON'T CARE) tRC tRAS tRP RAS tCRP tRPC UCAS/LCAS tASR ADDRESS I/O tRAH Row Row Open Don’t Care 18 Integrated Circuit Solution Inc. DR010-0D 11/26/2004 IC41C16100S IC41LV16100S CBR REFRESH CYCLE (Addresses; WE, OE = DON'T CARE) tRP tRAS tRP tRAS RAS tCHR tRPC tCP tCHR tRPC tCSR tCSR UCAS/LCAS Open I/O HIDDEN REFRESH CYCLE(1) (WE = HIGH; OE = LOW) tRAS tRP tRAS RAS tCRP tRCD tRSH tCHR UCAS/LCAS tAR tRAD tRAH tASC tASR ADDRESS Row tRAL tCAH Column tAA tRAC tOFF(2) tCAC tCLZ I/O Open Open Valid Data tOE tOD tORD OE Undefined Don’t Care Notes: 1. A Hidden Refresh may also be performed after a Write Cycle. In this case, WE = LOW and OE = HIGH. 2. tOFF is referenced from rising edge of RAS or CAS, whichever occurs last. Integrated Circuit Solution Inc. DR010-0D 11/26/2004 19 IC41C16100S IC41LV16100S SELF REFRESH CYCLE (Addresses : WE and OE = DON'T CARE) tRP tRASS tRPS VIH RAS V IL tRPC tCP tCHD tCSR tRPC tCP VIH UCAS/LCAS V IL VOH DQ V OL Open Don’t Care TIMING PARAMETERS Symbol -45 Min. Max. -50 Min. Max. -60 Min. Max. tCHD tCP tCSR tRASS tRP tRPS tRPC 8 7 5 100 28 77 5 8 9 5 100 30 84 5 10 9 5 100 40 104 5 — — — — — — — — — — — — — — — — — — — — — Units ns ns ns µs ns ns ns ORDERING INFORMATION: 5V (Pb-free) Commercial Range: 0°C to 70°C Speed (ns) 45 50 60 Order Part No. Package IC41C16100S-45K(G) IC41C16100S-45T(G) IC41C16100S-50K(G) IC41C16100S-50T(G) IC41C16100S-60K(G) IC41C16100S-60T(G) 400mil SOJ(Pb-free) 400mil TSOP-2(Pb-free) 400mil SOJ(Pb-free) 400mil TSOP-2(Pb-free) 400mil SOJ(Pb-free) 400mil TSOP-2(Pb-free) ORDERING INFORMATION: 5V (Pb-free) Industrial Range: -40°C to 85°C Speed (ns) 45 50 60 20 Order Part No. Package IC41C16100S-45KI(G) IC41C16100S-45TI(G) IC41C16100S-50KI(G) IC41C16100S-50TI(G) IC41C16100S-60KI(G) IC41C16100S-60TI(G) 400mil SOJ(Pb-free) 400mil TSOP-2(Pb-free) 400mil SOJ(Pb-free) 400mil TSOP-2(Pb-free) 400mil SOJ(Pb-free) 400mil TSOP-2(Pb-free) Integrated Circuit Solution Inc. DR010-0D 11/26/2004 IC41C16100S IC41LV16100S ORDERING INFORMATION: 3.3V (Pb-free) Commercial Range: 0°C to 70°C Speed (ns) 45 50 60 Order Part No. Package IC41LV16100S-45K(G) IC41LV16100S-45T(G) IC41LV16100S-50K(G) IC41LV16100S-50T(G) IC41LV16100S-60K(G) IC41LV16100S-60T(G) 400mil SOJ(Pb-free) 400mil TSOP-2(Pb-free) 400mil SOJ(Pb-free) 400mil TSOP-2(Pb-free) 400mil SOJ(Pb-free) 400mil TSOP-2(Pb-free) ORDERING INFORMATION: 3.3V (Pb-free) Industrial Range: -40°C to 85°C Speed (ns) 45 50 60 Order Part No. Package IC41LV16100S-45KI(G) IC41LV16100S-45TI(G) IC41LV16100S-50KI(G) IC41LV16100S-50TI(G) IC41LV16100S-60KI(G) IC41LV16100S-60TI(G) 400mil SOJ(Pb-free) 400mil TSOP-2(Pb-free) 400mil SOJ(Pb-free) 400mil TSOP-2(Pb-free) 400mil SOJ(Pb-free) 400mil TSOP-2(Pb-free) Integrated Circuit Solution Inc. HEADQUARTER: NO.2, TECHNOLOGY RD. V, SCIENCE-BASED INDUSTRIAL PARK, HSIN-CHU, TAIWAN, R.O.C. TEL: 886-3-5780333 Fax: 886-3-5783000 BRANCH OFFICE: 7F, NO. 106, SEC. 1, HSIN-TAI 5TH ROAD, HSICHIH TAIPEI COUNTY, TAIWAN, R.O.C. TEL: 886-2-26962140 FAX: 886-2-26962252 http://www.icsi.com.tw Integrated Circuit Solution Inc. DR010-0D 11/26/2004 21