ECP130 Series AC-DC Power Supplies 130 Watts • 100 W Convection/130 W Forced-cooled Ratings • 2” by 3” Footprint • Low 1.1” Profile • High Efficiency, up to 95% • Medical and ITE Approvals • High Power Density • Less than 0.5 W No Load Input Power • 3 Year Warranty The ECP130 series is designed to minimize the no load power consumption and maximize efficiency to facilitate equipment design to meet the latest environmental legislation. Approved for medical and ITE applications, this range of single output AC-DC power supplies are packaged in a low profile 1.1” height with a foot print of just 2” by 3”. The ECP130 provides up to 130 W force-cooled or 100 W convection-cooled leading to very high power densities of 19.7 W/in3 or 15.1 W/in3 respectively. The power supply contains two fuses and low leakage currents as required by medical applications and is safety approved to operate in a 80 °C ambient. The low profile and safety approvals covering ITE and medical standards along with conducted emissions to EN55011/22 level B allow the versatile ECP130 series to be used in a vast range of applications. Dimensions: ECP130: 3.00 x 2.00 x 1.10” (76.2 x 50.8 x 28.0 mm) Models & Ratings Output Current Convection-cooled Forced-cooled(1) Output Power Output Voltage 130 W 12.0 V 8.33 A 130 W 15.0 V 6.66 A 130 W 18.0 V 130 W Efficiency(2) Model Number(3) 10.83 A 93% ECP130PS12 8.66 A 93% ECP130PS15 5.55 A 7.22 A 93% ECP130PS18 24.0 V 4.16 A 5.41 A 93% ECP130PS24 130 W 28.0 V 3.57 A 4.64 A 93% ECP130PS28 130 W 36.0 V 2.77 A 3.61 A 93% ECP130PS36 130 W 48.0 V 2.08 A 2.70 A 93% ECP130PS48 Notes 1. Requires 10 CFM. 2. Typical efficiency measured at full load and 230VAC input. 3. Add suffix ‘-S’ for input and output screw terminals e.g. ECP130PS24-S Summary Characteristic Input Range Minimum Typical Maximum Units Notes & Conditions 85 115/230 264 VAC Derate load from 100% at 90 VAC to 85% at 85 VAC 0.5 W % 230 VAC (see fig.1 & 2) +80 °C See derating curve (fig.3) No Load Input Power Efficiency 95 Operating Temperature Safety Approvals 1 -30 ITE IEC60950, UL60950-1, CSA 22.2 No.60950-1-11 Ed 2, EN60950-1, LVD Medical IEC60601-1 Ed 3.1 Including Risk Management, ANSI/AAMI ES60601-1 & CSA C22.2 No.6061-1:08, EN60601-1 www.xppower.com ECP130 Series AC-DC Power Supplies Input Minimum Typical Maximum Units Notes & Conditions 85 115/230 264 VAC Derate output from 100% at 90 VAC to 85% at 85 VAC Input Frequency 47 50/60 63 Hz Power Factor 0.8 Characteristic Input Voltage - Operating Input Current - Full Load Inrush Current Earth Leakage Current 1.3/0.65 A 115/230 VAC 120 A 230 VAC cold start, 25 ºC 115/230 VAC/50 Hz (Typ), 264 VAC/60 Hz (Max) 20/40 No load Input Power Input Protection Agency approval, 47-63 Hz 230 VAC, 100% load EN61000-3-2 class A 50 µA 0.5 W F3.15 A/250 V Internal fuse fitted in line and neutral. Output - Main Output Characteristic Minimum Output Voltage 12 Typical Initial Set Accuracy Maximum Units Notes & Conditions 48 VDC See Models and Ratings table ±1 % Output Voltage Adjustment Minimum Load 0 Start Up Delay Hold Up Time 2 10 None A No minimum load required s 15/11 50% load, 115/230 VAC % ms 115/230 VAC full load. Min at full load, 115 VAC. Typical at 100W/ 130W Drift ±0.02 % After 20 min warm up Line Regulation ±0.5 % 90-264 VAC Load Regulation ±0.5 % 0-100% load. Transient Response 4 % Recovery within 1% in less than 500 µs for a 50-75% and 75-50% load step Over/Undershoot 7 % Full load Ripple & Noise 1 % pk-pk Overvoltage Protection 110 140 % Overload Protection 110 170 % I nom 0.02 %/˚C <2% from no load to 10% load, <1% above 10% load. 20 MHz bandwidth and 10 µF electrolytic capacitator in parallel with 0.1 µF ceramic capacitator. Vnom, recycle input to reset Short Circuit Protection Trip & Restart Temperature Coefficient General Characteristic Minimum Efficiency Isolation: Input to Output Input to Ground Output to Ground Switching Frequency Typical Maximum 95 % Weight Notes & Conditions 230 VAC (see fig. 1 & 2) 4000 VAC 2 MOPP 1500 VAC 1 MOPP 1500 VAC 1 MOPP kHz PFC 130 40 50 135 kHz 19.7/15.1 W/in3 Forced/convection-cooled 680 kHrs MIL-HDBK-217F, Notice 2 +25 °C GB 0.43(195) lb(g) Power Density Mean Time Between Failure Units www.xppower.com Main converter 2 ECP130 Series AC-DC Power Supplies Efficiency Vs Load Figure 1 ECP130PS12 12 V at 130 W 100% 95% 90% 115Vac input 85% Convection-Cooled Forced-Cooled 9 80% 230Vac input 75% 70% 10 20 30 40 50 60 70 80 90 100 Load (%) Figure 2 ECP130PS24 24 V at 130 W 100% 95% 90% 115Vac input 85% Convection-Cooled Forced-Cooled 230Vac input 80% 75% 70% 10 20 30 40 50 60 70 80 F 90 100 Load (%) Environmental Characteristic Maximum Units Operating Temperature -30 +80 °C Storage Temperature -40 +85 Cooling 10 Humidity 5 Operating Altitude 3 Minimum Typical Notes & Conditions See derating curve, fig.3 °C CFM Forced-cooled > 100W 95 %RH Non-condensing 5000 m Shock ±3 x 30g shocks in each plane, total 18 shocks. 30g = 11ms (+/- 0.5msecs), half sine. Conforms to EN60068-2-27 Vibration Single axis 10-500 Hz at 2g sweep and endurance at resonance in all 3 planes. Conforms to EN60068-2-6 www.xppower.com ECP130 Series AC-DC Power Supplies Temperature Derating Curve Figure 3 Output Load (%) 100 50 30 0 -30 0 +50 +70 +80 Ambient Temperature (ºC) EMC: Emissions Standard Test Level Conducted EN55011/22 Class B Radiated EN55011/22 Class A Harmonic Current EN61000-3-2 Class A Voltage Functions EN61000-3-3 Phenomenon Criteria Notes & Conditions Class B with King Core KSB RC 13 x 23 x 7 on input cable and KSB + 25 x 12 x 5 on output cable. EMC: Immunity Phenomenon Medical Device EMC Low Voltage PSU EMC Standard Test Level Criteria IEC60601-1-2 Ed.4.0 : 2014 as below as below EN61204-3 High severity level ESD EN61000-4-2 ±8kV contact, ±15kV air A Radiated EN61000-4-3 3 A A EFT EN61000-4-4 3 Surge EN61000-4-5 Installation class 3 A Conducted EN61000-4-6 3 A Magnetic Fields EN61000-4-8 4 A Dip >95% (0 VAC), 8.3 ms EN55024 (100 VAC) EN55024 (240 VAC) Dips and Interruptions EN60601-1-2 (100 VAC) A Dip >95% (0 VAC), 4160 ms Dip >95% (0 VAC), 10.0 ms B A Dip 30% (168 VAC), 500 ms A Dip >95% (0 VAC), 5000 ms Dip 100% (0 VAC), 10.0 ms B Dip 100% (0 VAC), 20 ms Dip 30% (70 VAC), 500 ms A A A B Dip 100% (0 VAC), 5000 ms B Dip 100% (0 VAC), 20 ms A Dip 100% (0 VAC), 10.0 ms EN60601-1-2 (240 VAC) A Dip 30% (70 VAC), 416 ms Dip 60% (40 VAC), 100 ms Dip 60% (96 VAC), 100 ms Dip 30% ( 168 VAC), 500 ms Dip 100% (0 VAC), 5000 ms www.xppower.com Notes & Conditions Performance criteria A <25 W A A A B 4 ECP130 Series AC-DC Power Supplies Safety Approvals Safety Agency Safety Standard Notes & Conditions CB Report IEC60950-1:2005 Information Technology UL UL60950-1, CSA 22.2 No.60950-1-11 Ed 2 Information Technology TUV EN60950-1 Information Technology CE LVD Safety Agency Safety Standard Notes & Conditions CB Report IEC60601-1 Ed 3.1 Including Risk Management Medical UL ANSI/AAMI ES60601-1: & CSA C22.2 No.6061-1:08 Medical CE EN60601-1 Medical Isolation Safety Standard Notes & Conditions Primary to Secondary 2 x MOPP (Means of Patient Protection) Primary to Earth 1 x MOPP (Means of Patient Protection) Secondary to Earth 1 x MOPP (Means of Patient Protection) IEC60601-1 Ed 3.1 Mechanical Details 0. 13 (3 .4 ) 3.00 (76.2) 2.75 (69.9) L4 4 1 .7 5 (44.5) 2.00 (50.8) CN2 CN1 - Input Connector Pin 1 Line Pin 2 Not Fitted Pin 3 Neutral Mates with JST housing VHR-4N and JST Series SVH-21T-P1.1 crimp terminals 1 Mounting hole marked with must be connected to safety earth C50 1 CN1 TR1 3 CN2 - Output Connector C2 0.09 (2.4) 0.06 (1.6) 0.89 (22.5) 0.13 (3.4) Pin 1 Notes 1. All dimensions shown in inches (mm). Tolerance: ±0.02 (0.5) 5 2. Weight: 0.43 lbs (195 g) approx. www.xppower.com Com Pin 2 Com Pin 3 +Vout Pin 4 +Vout Mates with JST housing VHR-6N and JST Series SVH-21T-P1.1 crimp terminals ECP130 Series AC-DC Power Supplies Thermal Considerations In order to ensure safe operation of the PSU in the end-use equipment, the temperature of the components listed in the table below must not be exceeded. Temperature should be monitored using thermocouples placed on the hottest part of the component (out of direct air flow). See Mechanical Details for component locations. Temperature Measurements (At Maximum Ambient) Max Temperature °C Component TR1 Coil 120°C L4 Coil 120°C C2 105°C C50 105°C Service Life The estimated service life of the ECP130 is determined by the cooling arrangements and load conditions experienced in the end application. Due to the uncertain nature of the end application this estimated service life is based on the actual measured temperature of key capacitors with in the product when installed by the end application, The graph below expresses the estimated lifetime based on the temperature of these key components based on the average temperature over the lifetime of the equipment. Estimated Service Life vs Component Temperature Figure 4 80000 70000 60000 Lifetime (Hrs) 50000 C2 & C50 40000 30000 20000 10000 0 105 95 85 75 65 C2 + C52 Temperature (ºC) www.xppower.com 16-Nov-15