CREE C12360-STRADA-2X2-DNW Strada-module sery Datasheet

PRODUCT DATASHEET
Strada-Module series
last update 17/9/2012
Ordering number C12362_STRADA-2X2-DWC
Family
Type
LED
Color
Diameter
Height
Style
Optic Material
Holder Material
Fastening
Status
Strada-Module
Lens
XM-L
Clear
50x50 mm
6 mm
Square
PMMA
Screw, pin, glue
Ready
FWHM
Efficiency
cd/lm
Gerber File
Asym degrees
92 %
0.410
Available
FWHM
Efficiency
cd/lm
Gerber File
Asym degrees
93 %
0.420
Available
FWHM
Efficiency
cd/lm
Gerber File
Asym degrees
93 %
0.270
Available
Ordering number C12419_STRADA-2X2-A-T
Family
Type
LED
Color
Diameter
Height
Style
Optic Material
Holder Material
Fastening
Status
Strada-Module
Lens
XM-L
Clear
50x50 mm
7.3 mm
Rectangular
PMMA
Screw, pin, glue
Ready
Ordering number C12360_STRADA-2X2-DNW
Family
Type
LED
Color
Diameter
Height
Style
Optic Material
Holder Material
Fastening
Status
Strada-Module
Lens
XM-L
Clear
50x50 mm
11 mm
Square
PMMA
Screw, pin, glue
Ready
NOTE: The typical divergence will be changed by different color, chip size and chip position
tolerance. The typical total divergence is the full angle measured where the luminous intensity
is half of the peak value.
October 17th 2012 0:07 Copyright Ledil Oy - Subject to change without prior notice - Page 1/2
Ledil Oy
Salorankatu 10
24240 SALO
Finland
http://www.ledil.com
email: [email protected]
FAX: +358-2-733 8001
PRODUCT DATASHEET
Strada-Module series
last update 17/9/2012
GENERAL INFORMATION
- Product series especially designed & optimized for XM-L series of LEDs.
- Special care taken to make light distribution as uniform as possible.
- Lens material optical grade PMMA with high UV and temperature resistance (105 degrees of Celcius / 220
degrees of Fahrenheit). Allows use of high current and temperature conditions.
Please find more information about used material from below:
http://ledil.fi/sites/default/files/Documents/Technical/Material/PMMA%208N%20UL94_Yellow%20Card.pdf
http://ledil.fi/sites/default/files/Documents/Technical/Material/PMMA%208N%20PLEXIGLAS-Datasheet.pdf
- Fastening to PCB with appropriate adhesive. By clicking link below you can find Ledil recommended glue
options.
http://www.ledil.com/datasheets/DataSheet_GLUES.pdf
NOTE 1: We advise customer to ensure the suitability and sufficiency of the bond in the end
product. For example, mechanical stress, vibration and holes on the surface of the circuit boar
weaken the strength of the glue.
NOTE 2: All surfaces where glue is applied must be clean, dry and free from grease and dirt. If
cleaning of PCB surfaces is needed, please follow strictly the cleaning instructions of your LED
manufacturer -this is important as cleaning shall under no circumstances damage LEDs or other
electronics components on the PCB.
Further note that optical components shall not be cleaned with any chemicals - only micro fiber
cloth may be used to remove fingerprints or other traces from handling.
October 17th 2012 0:07 Copyright Ledil Oy - Subject to change without prior notice - Page 2/2
Ledil Oy
Salorankatu 10
24240 SALO
Finland
http://www.ledil.com
email: [email protected]
FAX: +358-2-733 8001
Similar pages