LP3879 www.ti.com SNVS396B – MAY 2006 – REVISED APRIL 2013 LP3879 Micropower 800mA Low Noise "Ceramic Stable" Voltage Regulator for Low Voltage Applications Check for Samples: LP3879 FEATURES DESCRIPTION • • The LP3879 is a 800 mA fixed-output voltage regulator designed to provide high performance and low noise in applications requiring output voltages between 1.0V and 1.2V. 1 2 • • • • • • • • • • • Standard Output Voltage: 1.00V, 1.20V Custom Voltages Available from 1.0V to 1.2V (50 mV Increments) Input Voltage: 2.5 to 6V 1% Initial Output Accuracy Designed for Use with Low ESR Ceramic Capacitors Very Low Output Noise Sense Option Improves Load Regulation 8-Lead SO PowerPad and WSON Surface Mount Packages <10 μA Quiescent Current in Shutdown Low Ground Pin Current at all Loads High Peak Current Capability Over-Temperature/Over-Current Protection -40°C to +125°C Junction Temperature Range Using an optimized VIP (Vertically Integrated PNP) process, the LP3879 delivers superior performance: Ground Pin Current: Typically 5.5 mA @ 800 mA load, and 200 µA @ 100 µA load. Low Power Shutdown: The LP3879 draws less than 10 μA quiescent current when shutdown pin is pulled low. Precision Output: Ensured output voltage accuracy is 1% at room temperature. Low Noise: Broadband output noise is only 18 μV (typical) with 10 nF bypass capacitor. APPLICATIONS • • • • ASIC Power Supplies In: – Desktops, Notebooks and Graphic Cards – Set Top Boxes, Printers and Copiers DSP and FPGA Power Supplies SMPS Post-Regulator Medical Instrumentation 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2006–2013, Texas Instruments Incorporated LP3879 SNVS396B – MAY 2006 – REVISED APRIL 2013 www.ti.com Basic Application Circuit OUTPUT 6 *4.7 PF (Ceramic or Tantalum recommended) 4 1 5 + *0.01 PF (See App Hints) + - 2 N/C 7 N/C *10 PF (Ceramic recommended) 8 **S/D + LP3879-X.X 1.23V + 3 *Capacitance values shown are minimum required to assure stability. Larger output capacitor provides improved dynamic response. Output capacitor must meet ESR requirements (see Application Information). **The Shutdown pin must be actively terminated (see Application Information). Tie to INPUT (Pin 4) if not used. Connection Diagram GROUND 3 INPUT 4 GND 8 SHUTDOWN 7 N/C BYPASS 1 N/C 2 GROUND 3 INPUT 4 8 SHUTDOWN 7 N/C 6 SENSE 5 OUTPUT 6 SENSE 5 OUTPUT Figure 1. Top View 8-Lead SO PowerPad See DDA0008B Package GROUND BYPASS 1 N/C 2 Figure 2. Top View 8-Lead WSON See NGT0008A Package PIN DESCRIPTIONS Pin Name 1 BYPASS 2 N/C 3 GROUND 4 INPUT 5 OUTPUT 6 SENSE 7 N/C Function The capacitor connected between BYPASS and GROUND lowers output noise voltage level and is required for loop stability. DO NOT CONNECT. This pin is used for post package test and must be left floating. Device ground. Input source voltage. Regulated output voltage. Remote Sense. Tie directly to output or remotely at point of load for best regulation. No internal connection. 8 SHUTDOWN Output is enabled above turn-on threshold voltage. Pull down to turn off regulator output. SO PowerPad, WSON SUBSTRATE GROUND The exposed die attach pad should be connected to a thermal pad at ground potential. For additional information on using Texas Instruments' Non Pull Back WSON package, please refer to WSON application note SNOA401 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 2 Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated Product Folder Links: LP3879 LP3879 www.ti.com SNVS396B – MAY 2006 – REVISED APRIL 2013 Absolute Maximum Ratings (1) (2) Storage Temperature Range −65°C to +150°C Operating Junction Temperature Range -40°C to +125°C Lead Temperature (Soldering, 5 seconds) 260°C ESD Rating (3) 2 kV Shutdown Pin 1kV Power Dissipation (4) Internally Limited −0.3V to +16V Input Supply Voltage (Survival) Input Supply Voltage (Typical Operating) 2.5V to +6V SENSE Pin −0.3V to +6V Output Voltage (Survival) (5) −0.3V to +6V IOUT (Survival) Short Circuit Protected Input-Output Voltage (Survival) (6) (1) (2) (3) (4) (5) (6) −0.3V to +16V Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Electrical specifications do not apply when operating the device outside of its rated operating conditions. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and specifications. ESD testing was performed using Human Body Model, a 100 pF capacitor discharged through a 1.5 kΩ resistor. The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(MAX), the junction-to-ambient thermal resistance, θJ−A, and the ambient temperature, TA. The maximum allowable power dissipation at any ambient temperature is calculated using: The value of θJ−A for the WSON and SO PowerPad packages are specifically dependent on PCB trace area, trace material, and the number of layers and thermal vias. If a four layer board is used with maximum vias from the IC center to the heat dissipating copper layers, values of θJ−A which can be obtained are approximately 60°C/W for the SO PowerPad and 40°C/W for the WSON package. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. If used in a dual-supply system where the regulator load is returned to a negative supply, the LP3879 output must be diode-clamped to ground. The output PNP structure contains a diode between the VIN and VOUT terminals that is normally reverse-biased. Forcing the output above the input will turn on this diode and may induce a latch-up mode which can damage the part (see Application Hints). Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated Product Folder Links: LP3879 3 LP3879 SNVS396B – MAY 2006 – REVISED APRIL 2013 www.ti.com Electrical Characteristics Limits in standard typeface are for TJ = 25°C, and limits in boldface type apply over the temperature range of -40°C to 125°C. Limits are ensured through design, testing, or correlation. The limits are used to calculate the Average Outgoing Quality Level (AOQL). Unless otherwise specified: VIN = 3.0V, VOUT = 1V, IL = 1 mA, COUT = 10 µF, CIN = 4.7 µF, VS/D = 2V, CBYPASS = 10 nF. Symbol Parameter Conditions VO Output Voltage Tolerance 'VOUT 'VIN Output Voltage Line Regulation VIN (min) Minimum Input Voltage Required To Maintain Output Regulation IGND Ground Pin Current 1 mA ≤ IL ≤ 800 mA, 3.0V ≤ VIN ≤ 6V Min (1) Typical (2) Max (1) -1.0 1.00 1.0 -2.0 -3.0 1.00 2.0 3.0 Units %Vnom 0.014 3.0V ≤ VIN ≤ 6V 0.007 0.032 IL = 800 mA, VOUT ≥ VOUT(NOM) - 1% 2.5 3.1 IL = 800 mA, VOUT ≥ VOUT(NOM) - 1% 0 ≤ TJ ≤ 125°C 2.5 2.8 IL = 750 mA, VOUT ≥ VOUT(NOM) - 1% 2.5 IL = 100 µA 200 IL = 200 mA 1.5 IL = 800 mA 5.5 %/V V 3.0 250 275 µA 2 3.3 8.5 mA 15 IO(PK) Peak Output Current VOUT ≥ VOUT(NOM) − 5% 1200 IO(MAX) Short Circuit Current RL = 0 (Steady State) 1400 en Output Noise Voltage (RMS) BW = 100 Hz to 100 kHz CBYPASS = 10 nF 18 µV(RMS) 'VOUT 'VIN Ripple Rejection f = 1 kHz 60 dB mA SHUTDOWN INPUT VS/D VH = Output ON S/D Input Voltage IS/D (1) (2) 4 S/D Input Current VL = Output OFF, IIN ≤ 10 µA 1.4 0.1 1.6 0.50 V VOUT ≤ 10 mV, IIN ≤ 50 µA 0.6 VS/D = 0 0.02 −1 5 15 VS/D = 5V µA Limits are ensured through testing, statistical correlation, or design. Typical numbers reperesent the most likely norm for 25°C operation. Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated Product Folder Links: LP3879 LP3879 www.ti.com SNVS396B – MAY 2006 – REVISED APRIL 2013 Typical Performance Characteristics Unless otherwise specified: VIN = 3.3V, VOUT = 1V, IL = 1 mA, CIN = 4.7 µF, COUT = 10 µF, VS/D = 2V, CBYP = 10 nF, TJ = 25°C. IGND vs Temperature Minimum VIN Over Temperature 10.0 9.0 8.0 IGND (mA) 7.0 IL = 800 mA 6.0 5.0 4.0 3.0 IL = 240 mA 2.0 1.0 IL = 1 mA 0 -60 -40 -20 0 20 40 60 80 100 120 140 TEMPERATURE (°C) Figure 3. Figure 4. IGND vs ILoad VOUT vs Temperature 1.020 1.015 VOUT (V) 1.010 1.005 1.000 0.995 0.990 0.985 0.980 -50 -25 0 25 50 75 100 125 TEMPERATURE (oC) Figure 5. Figure 6. VOUT vs Temperature Ripple Rejection 1.202 100 90 VOUT = 1.2V 80 RIPPLE REJECTION (dB) VOUT (V) 1.201 1.200 1.199 70 60 50 40 30 20 10 1.198 -40 -25 0 25 50 75 100 125 0 10 100 1k 10k 100k 1M JUNCTION TEMPERATURE (ºC) FREQUENCY (Hz) Figure 7. Figure 8. Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated Product Folder Links: LP3879 5 LP3879 SNVS396B – MAY 2006 – REVISED APRIL 2013 www.ti.com Typical Performance Characteristics (continued) Unless otherwise specified: VIN = 3.3V, VOUT = 1V, IL = 1 mA, CIN = 4.7 µF, COUT = 10 µF, VS/D = 2V, CBYP = 10 nF, TJ = 25°C. Ripple Rejection Line Transient Response 100 90 IL= 800 mA RIPPLE REJECTION (dB) 80 70 60 50 40 30 20 10 0 10 100 1k 10k 100k 1M FREQUENCY (Hz) 6 Figure 9. Figure 10. Line Transient Response Line Transient Response Figure 11. Figure 12. Line Transient Response Line Transient Response Figure 13. Figure 14. Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated Product Folder Links: LP3879 LP3879 www.ti.com SNVS396B – MAY 2006 – REVISED APRIL 2013 Typical Performance Characteristics (continued) Unless otherwise specified: VIN = 3.3V, VOUT = 1V, IL = 1 mA, CIN = 4.7 µF, COUT = 10 µF, VS/D = 2V, CBYP = 10 nF, TJ = 25°C. Line Transient Response Load Transient Response Figure 15. Figure 16. Load Transient Response Turn-On Characteristics 1.2 1 0o C VOUT (V) 0.8 0.6 25oC 0.4 125oC 0.2 0 0 0.5 1 1.5 2 VS/D Figure 17. Figure 18. Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated Product Folder Links: LP3879 7 LP3879 SNVS396B – MAY 2006 – REVISED APRIL 2013 www.ti.com Block Diagram SENSE BYPASS INPUT OUTPUT 6 1 4 5 Error Amp 2 N/C 8 SHUTDOWN 7 N/C + - LP3879-X.X 1.23V GROUND + 3 APPLICATION INFORMATION PACKAGE INFORMATION The LP3879 is offered in the 8-lead SO PowerPad or WSON surface mount packages to allow for increased power dissipation compared to the SO-8 and Mini SO-8. EXTERNAL CAPACITORS Like any low-dropout regulator, the LP3879 requires external capacitors for regulator stability. These capacitors must be correctly selected for good performance. INPUT CAPACITOR: A capacitor whose value is at least 4.7 µF (±20%) is required between the LP3879 input and ground. A good quality X5R / X7R ceramic capacitor should be used. Capacitor tolerance and temperature variation must be considered when selecting a capacitor (see Capacitor Characteristics section) to assure the minimum requirement of input capacitance is met over all operating conditions. The input capacitor must be located not more than 0.5" from the input pin and returned to a clean analog ground. Any good quality ceramic or tantalum capacitor may be used, assuming the minimum input capacitance requirement is met. OUTPUT CAPACITOR: The LP3879 requires a ceramic output capacitor whose size is at least 10 µF (±20%). A good quality X5R / X7R ceramic capacitor should be used. Capacitance tolerance and temperature characteristics must be considered when selecting an output capacitor. The LP3879 is designed specifically to work with ceramic output capacitors, utilizing circuitry which allows the regulator to be stable across the entire range of output current with an ultra low ESR output capacitor. The output capacitor selected must meet the requirement for minimum amount of capacitance and also have an ESR (equivalent series resistance) value which is within the stable range. A curve is provided which shows the stable ESR range as a function of load current (see Figure 19). 8 Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated Product Folder Links: LP3879 LP3879 www.ti.com SNVS396B – MAY 2006 – REVISED APRIL 2013 0.4 ESR (:) 0.3 0.2 STABLE REGION 0.1 0 0 200 400 600 800 LOAD CURRENT (mA) Figure 19. Stable Region For Output Capacitor ESR Important: The output capacitor must maintain its ESR within the stable region over the full operating temperature range of the application to assure stability. The output capacitor ESR forms a zero which is required to add phase lead near the loop gain crossover frequency, typically in the range of 50kHz to 200 kHz. The ESR at lower frequencies is of no importance. Some capacitor manufacturers list ESR at low frequencies only, and some give a formula for Dissipation Factor which can be used to calculate a value for a term referred to as ESR. However, since the DF formula is usually at a much lower frequency than the range listed above, it will give an unrealistically high value. If good quality X5R or X7R ceramic capacitors are used, the actual ESR in the 50 kHz to 200 kHz range will not exceed 25 milli Ohms. If these are used as output capacitors for the LP3879, the regulator stability requirements are satisfied. It is important to remember that capacitor tolerance and variation with temperature must be taken into consideration when selecting an output capacitor so that the minimum required amount of output capacitance is provided over the full operating temperature range. (See Capacitor Characteristics section). The output capacitor must be located not more than 0.5" from the output pin and returned to a clean analog ground. NOISE BYPASS CAPACITOR: The 10 nF capacitor on the Bypass pin significantly reduces noise on the regulator output and is required for loop stability. However, the capacitor is connected directly to a highimpedance circuit in the bandgap reference. Because this circuit has only a few microamperes flowing in it, any significant loading on this node will cause a change in the regulated output voltage. For this reason, DC leakage current through the noise bypass capacitor must never exceed 100 nA, and should be kept as low as possible for best output voltage accuracy. The types of capacitors best suited for the noise bypass capacitor are ceramic and film. High-quality ceramic capacitors with either NPO or COG dielectric typically have very low leakage. 10 nF polypropolene and polycarbonate film capacitors are available in small surface-mount packages and typically have extremely low leakage current. CAPACITOR CHARACTERISTICS CERAMIC: The LP3879 was designed to work with ceramic capacitors on the output to take advantage of the benefits they offer: for capacitance values in the 10 µF range, ceramics are the least expensive and also have the lowest ESR values (which makes them best for eliminating high-frequency noise). The ESR of a typical 10 µF ceramic capacitor is in the range of 5 mΩ to 10 mΩ, which meets the ESR limits required for stability by the LP3879. One disadvantage of ceramic capacitors is that their capacitance can vary with temperature. Many large value ceramic capacitors (≥ 2.2 µF) are manufactured with the Z5U or Y5V temperature characteristic, which results in the capacitance dropping by more than 50% as the temperature goes from 25°C to 85°C. Another significant problem with Z5U and Y5V dielectric devices is that the capacitance drops severely with applied voltage. A typical Z5U or Y5V capacitor can lose 60% of its rated capacitance with half of the rated voltage applied to it. Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated Product Folder Links: LP3879 9 LP3879 SNVS396B – MAY 2006 – REVISED APRIL 2013 www.ti.com For these reasons, X7R and X5R type ceramic capacitors must be used on the input and output of the LP3879. SHUTDOWN INPUT OPERATION The LP3879 is shut off by pulling the Shutdown input low, and turned on by pulling it high. If this feature is not to be used, the Shutdown input should be tied to VIN to keep the regulator output on at all times. To assure proper operation, the signal source used to drive the Shutdown input must be able to swing above and below the specified turn-on/turn-off voltage thresholds listed in the Electrical Characteristics section under VON/OFF. REVERSE INPUT-OUTPUT VOLTAGE The PNP power transistor used as the pass element in the LP3879 has an inherent diode connected between the regulator output and input. During normal operation (where the input voltage is higher than the output) this diode is reverse-biased. However, if the output is pulled above the input, this diode will turn ON and current will flow into the regulator output. In such cases, a parasitic SCR can latch which will allow a high current to flow into VIN (and out the ground pin), which can damage the part. In any application where the output may be pulled above the input, an external Schottky diode must be connected from VIN to VOUT (cathode on VIN, anode on VOUT), to limit the reverse voltage across the LP3879 to 0.3V (see Absolute Maximum Ratings). 10 Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated Product Folder Links: LP3879 LP3879 www.ti.com SNVS396B – MAY 2006 – REVISED APRIL 2013 REVISION HISTORY Changes from Revision A (April 2013) to Revision B • Page Changed layout of National Data Sheet to TI format .......................................................................................................... 10 Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated Product Folder Links: LP3879 11 PACKAGE OPTION ADDENDUM www.ti.com 1-Nov-2013 PACKAGING INFORMATION Orderable Device Status (1) LP3879MR-1.0/NOPB Package Type Package Pins Package Drawing Qty Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) DDA 8 95 Green (RoHS & no Sb/Br) SN | CU SN Level-3-260C-168 HR 3879 MR1.0 SO PowerPAD DDA 8 95 TBD Call TI Call TI LP3879 MR1.2 LP3879MR-1.2/NOPB ACTIVE SO PowerPAD DDA 8 95 Green (RoHS & no Sb/Br) CU SN Level-3-260C-168 HR LP3879 MR1.2 LP3879MRX-1.0/NOPB ACTIVE SO PowerPAD DDA 8 2500 Green (RoHS & no Sb/Br) SN | CU SN Level-3-260C-168 HR 3879 MR1.0 LP3879MRX-1.2/NOPB ACTIVE SO PowerPAD DDA 8 2500 Green (RoHS & no Sb/Br) CU SN Level-3-260C-168 HR LP3879 MR1.2 LP3879MR-1.2 ACTIVE SO PowerPAD Eco Plan NRND LP3879SD-1.0 NRND WSON NGT 8 1000 TBD Call TI Call TI 79SD1.0 LP3879SD-1.0/NOPB ACTIVE WSON NGT 8 1000 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM 79SD1.0 LP3879SD-1.2/NOPB ACTIVE WSON NGT 8 1000 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM 79SD1.2 LP3879SDX-1.0/NOPB ACTIVE WSON NGT 8 4500 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM 79SD1.0 LP3879SDX-1.2/NOPB ACTIVE WSON NGT 8 4500 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM 79SD1.2 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 1-Nov-2013 (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 11-Oct-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LP3879MRX-1.0/NOPB SO Power PAD DDA 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LP3879MRX-1.2/NOPB SO Power PAD DDA 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LP3879SD-1.0 WSON NGT 8 1000 178.0 12.4 4.3 4.3 1.3 8.0 12.0 Q1 LP3879SD-1.0/NOPB WSON NGT 8 1000 178.0 12.4 4.3 4.3 1.3 8.0 12.0 Q1 LP3879SD-1.2/NOPB WSON NGT 8 1000 178.0 12.4 4.3 4.3 1.3 8.0 12.0 Q1 LP3879SDX-1.0/NOPB WSON NGT 8 4500 330.0 12.4 4.3 4.3 1.3 8.0 12.0 Q1 LP3879SDX-1.2/NOPB WSON NGT 8 4500 330.0 12.4 4.3 4.3 1.3 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 11-Oct-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LP3879MRX-1.0/NOPB SO PowerPAD DDA 8 2500 367.0 367.0 35.0 LP3879MRX-1.2/NOPB SO PowerPAD DDA 8 2500 367.0 367.0 35.0 LP3879SD-1.0 WSON NGT 8 1000 210.0 185.0 35.0 LP3879SD-1.0/NOPB WSON NGT 8 1000 210.0 185.0 35.0 LP3879SD-1.2/NOPB WSON NGT 8 1000 210.0 185.0 35.0 LP3879SDX-1.0/NOPB WSON NGT 8 4500 367.0 367.0 35.0 LP3879SDX-1.2/NOPB WSON NGT 8 4500 367.0 367.0 35.0 Pack Materials-Page 2 MECHANICAL DATA DDA0008B MRA08B (Rev B) www.ti.com MECHANICAL DATA NGT0008A SDC08A (Rev A) www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2013, Texas Instruments Incorporated