Cooper DRQ73-330-R Dual winding, shielded inductors/transformer Datasheet

DRQ Series
Dual Winding, Shielded Inductors/Transformer
Description
• 125°C maximum total operating temperature
• Dual winding inductors that can be used as either
a single inductor, or in coupled inductor/transformer applications
(1:1 turns ratio)
• Four sizes of shielded drum core inductors
• Windings can be connected in series or parallel, offering a broad
range of inductance and current ratings
Part Number
DRQ73-R33-R
DRQ73-1R0-R
DRQ73-1R5-R
DRQ73-2R2-R
DRQ73-3R3-R
DRQ73-4R7-R
DRQ73-6R8-R
DRQ73-8R2-R
DRQ73-100-R
DRQ73-150-R
DRQ73-220-R
DRQ73-330-R
DRQ73-470-R
DRQ73-680-R
DRQ73-820-R
DRQ73-101-R
Rated
Inductance
(µH)
0.33
1.00
1.50
2.20
3.30
4.70
6.80
8.20
10.0
15.0
22.0
33.0
47.0
68.0
82.0
100
OCL(1)
+/-20%
(µH)
0.306
0.992
1.482
2.070
3.540
4.422
6.480
8.930
10.30
15.01
22.65
34.41
48.62
68.91
80.37
101.4
Irms(2)
Amps
6.19
5.25
4.64
4.11
3.31
3.09
2.55
2.19
2.08
1.83
1.62
1.31
1.08
0.89
0.86
0.73
Parallel Ratings
Isat(3)
Amps
Peak
14.4
7.97
6.52
5.52
4.22
3.78
3.12
2.66
2.47
2.05
1.67
1.35
1.14
0.96
0.89
0.79
DCR Ω (4)
typ.
Volt(5)
µ-Sec
0.0074
0.0103
0.0132
0.0167
0.0259
0.0297
0.0435
0.0592
0.0656
0.0844
0.107
0.166
0.241
0.358
0.384
0.527
1.98
3.56
4.36
5.15
6.73
7.52
9.11
10.7
11.5
13.9
17.0
21.0
24.9
29.7
32.1
36.0
1) Open Circuit Inductance Test Parameters: 100kHz, 0.25 Vrms, 0.0 Adc
Parallel: (1,2 -4,3) Series: (1-4) tie (2-3)
2) RMS current for an approximate ∆T of 40°C without core loss. It is recommended that the
temperature of the part not exceed 125°C.
3) Peak current for approximately 30% roll-off at 20°C
4) DCR limits @ 20°C
5) Applied Volt-Time product (V-µS) across the inductor. This value represents the applied V-µS
at 100KHz necessary to generate a core loss equal to 10% of the total losses for a 40°C
temperature rise.
1207
BU-SB07326
• Peak current ratings from 0.13 amps to 56 amps
• RMS current ratings from 0.128 amps to 17.9 amps
• Inductance ratings from 0.33µH to 4.02mH
• Surface Mount
• 200Vac Isolation between windings
• Ferrite core material
Applications
• As a transformer: SEPIC, flyback
• As an inductor: buck, boost, coupled inductor
• DC-DC converters
• VRM inductor for CPU and DDR power supplies
• Input and output filter chokes
Environmental Data
• Storage temperature: -40°C to +125°C
• Operating temperature: -40°C to +125°C (range is application
specific).
• Solder reflow temperature: 260°C max. for 10 seconds max.
Packaging
• Supplied in tape and reel packaging, 1350 (DRQ73),
1100 (DRQ74), 600 (DRQ125), and 350 (DRQ127) per reel
Page 1 of 7
OCL(1)
+/-20%
(µH)
1.224
3.968
5.928
8.280
14.16
17.69
25.92
35.72
41.20
60.04
90.60
137.6
194.5
275.6
321.5
405.6
Irms(2)
Amps
3.10
2.63
2.32
2.06
1.66
1.55
1.28
1.10
1.04
0.916
0.811
0.653
0.542
0.444
0.430
0.367
Series Ratings
Isat(3)
DCR Ω (4)
Amps
typ.
Peak
7.18
0.0296
3.99
0.0411
3.26
0.0527
2.76
0.0669
2.11
0.1035
1.89
0.1188
1.56
0.1742
1.33
0.2368
1.24
0.2623
1.03
0.339
0.83
0.429
0.68
0.665
0.57
0.965
0.48
1.43
0.44
1.54
0.39
2.11
6) Turns Ratio (1:3):(2-4) 1:1
7) Part number definition: DRQxxx-yyy-R
DRQxxx = product code and size,
-yyy = inductance value in µH,
R = decimal point. If no R is present, third character = # of zeros
-R suffix = RoHS compliant
Data Sheet 4311
Volt(5)
µ-Sec
3.96
7.12
8.72
10.3
13.5
15.0
18.2
21.4
23.0
27.8
34.0
42.0
49.8
59.4
64.2
72.0
Part Number
DRQ73-151-R
DRQ73-221-R
DRQ73-331-R
DRQ73-471-R
DRQ73-681-R
DRQ73-821-R
DRQ73-102-R
DRQ74-R33-R
DRQ74-1R0-R
DRQ74-1R5-R
DRQ74-2R2-R
DRQ74-3R3-R
DRQ74-4R7-R
DRQ74-6R8-R
DRQ74-8R2-R
DRQ74-100-R
DRQ74-150-R
DRQ74-220-R
DRQ74-330-R
DRQ74-470-R
DRQ74-680-R
DRQ74-820-R
DRQ74-101-R
DRQ74-151-R
DRQ74-221-R
DRQ74-331-R
DRQ74-471-R
DRQ74-681-R
DRQ74-821-R
DRQ74-102-R
DRQ125-R47-R
DRQ125-1R0-R
DRQ125-1R5-R
DRQ125-2R2-R
DRQ125-3R3-R
DRQ125-4R7-R
DRQ125-6R8-R
DRQ125-8R2-R
DRQ125-100-R
DRQ125-150-R
DRQ125-220-R
DRQ125-330-R
DRQ125-470-R
DRQ125-680-R
Rated
Inductance
(µH)
150
220
330
470
680
820
1000
0.33
1.00
1.50
2.20
3.30
4.70
6.80
8.20
10.0
15.0
22.0
33.0
47.0
68.0
82.0
100
150
220
330
470
680
820
1000
0.47
1.00
1.50
2.20
3.30
4.70
6.80
8.20
10.0
15.0
22.0
33.0
47.0
68.0
OCL(1)
+/-20%
(µH)
150.9
223.3
325.5
465.8
676.5
821.7
995.0
0.294
0.952
1.422
1.986
3.396
5.182
7.344
8.566
9.882
16.09
21.73
33.01
49.64
69.67
80.95
101.6
150.0
227.0
335.6
465.3
671.2
812.7
1009
0.456
0.894
1.478
2.208
3.084
5.274
6.588
8.048
9.654
15.35
22.36
33.74
47.47
67.91
Irms(2)
Amps
0.58
0.52
0.42
0.35
0.29
0.27
0.26
6.20
5.33
4.96
4.66
3.94
3.34
2.60
2.53
2.41
2.11
1.75
1.41
1.15
1.03
0.91
0.86
0.69
0.56
0.45
0.40
0.33
0.31
0.27
17.6
15.0
13.8
10.9
9.26
7.18
6.64
5.54
5.35
4.27
3.70
3.28
2.71
2.22
Parallel Ratings
Isat(3)
Amps
Peak
0.65
0.53
0.44
0.37
0.31
0.28
0.25
18.4
10.2
8.35
7.06
5.40
4.37
3.67
3.40
3.17
2.48
2.13
1.73
1.41
1.19
1.11
0.99
0.81
0.66
0.54
0.46
0.38
0.35
0.31
33.0
23.6
18.3
15.0
12.7
9.71
8.68
7.86
7.17
5.69
4.71
3.84
3.24
2.70
DCR Ω (4)
typ.
Volt(5)
µ-Sec
0.851
1.05
1.59
2.36
3.47
3.93
4.34
0.0074
0.0100
0.0115
0.0130
0.0183
0.0254
0.0418
0.0441
0.0489
0.0637
0.0925
0.143
0.216
0.265
0.345
0.383
0.591
0.907
1.41
1.74
2.58
2.93
3.89
0.0018
0.0024
0.0029
0.0045
0.0063
0.0105
0.0123
0.0176
0.0189
0.0298
0.0396
0.0505
0.0740
0.101
44.0
53.5
64.5
77.2
93.1
103
113
1.71
3.08
3.76
4.45
5.81
7.18
8.55
9.23
9.92
12.7
14.7
18.1
22.2
26.3
28.4
31.8
38.6
47.5
57.8
68.1
81.7
89.9
100
3.17
4.43
5.70
6.97
8.23
10.8
12.0
13.3
14.6
18.4
22.2
27.2
32.3
38.6
1) Open Circuit Inductance Test Parameters: 100kHz, 0.25 Vrms, 0.0 Adc
Parallel: (1,2 -4,3) Series: (1-4) tie (2-3)
2) RMS current for an approximate ∆T of 40°C without core loss. It is recommended that the
temperature of the part not exceed 125°C.
3) Peak current for approximately 30% roll-off at 20°C
4) DCR limits @ 20°C
5) Applied Volt-Time product (V-µS) across the inductor. This value represents the applied V-µS
at 100KHz necessary to generate a core loss equal to 10% of the total losses for a 40°C
temperature rise.
1207
BU-SB07326
Page 2 of 7
OCL(1)
+/-20%
(µH)
603.6
893.2
1302
1863
2706
3287
3980
1.176
3.808
5.688
7.944
13.58
20.73
29.38
34.26
39.53
64.36
86.92
132.0
198.6
278.7
323.8
406.4
600.0
908.0
1342
1861
2685
3251
4036
1.824
3.576
5.912
8.832
12.34
21.10
26.35
32.19
38.62
61.40
89.44
135.0
189.9
271.6
Irms(2)
Amps
0.289
0.260
0.211
0.173
0.143
0.134
0.128
3.10
2.66
2.48
2.33
1.97
1.67
1.30
1.27
1.20
1.05
0.874
0.702
0.573
0.517
0.453
0.430
0.346
0.279
0.224
0.202
0.166
0.156
0.135
8.80
7.51
6.89
5.46
4.63
3.59
3.32
2.77
2.67
2.13
1.84
1.64
1.35
1.11
Series Ratings
Isat(3)
DCR Ω (4)
Amps
typ.
Peak
0.32
3.41
0.27
4.20
0.22
6.36
0.18
9.44
0.15
13.88
0.14
15.72
0.13
17.36
9.18
0.0295
5.10
0.0400
4.17
0.0461
3.53
0.0521
2.70
0.0732
2.19
0.102
1.84
0.167
1.70
0.177
1.58
0.196
1.24
0.255
1.07
0.371
0.87
0.574
0.71
0.865
0.60
1.06
0.55
1.38
0.49
1.53
0.41
2.37
0.33
3.63
0.27
5.66
0.23
6.97
0.19
10.3
0.17
11.7
0.16
15.6
16.5
0.0078
11.8
0.0096
9.15
0.0114
7.50
0.0182
6.35
0.0253
4.86
0.0420
4.34
0.0492
3.93
0.0705
3.59
0.0757
2.85
0.120
2.36
0.159
1.92
0.203
1.62
0.297
1.35
0.440
6) Turns Ratio (1:3):(2-4) 1:1
7) Part number definition: DRQxxx-yyy-R
DRQxxx = product code and size,
-yyy = inductance value in µH,
R = decimal point. If no R is present, third character = # of zeros
-R suffix = RoHS compliant
Data Sheet 4311
Volt(5)
µ-Sec
88.0
107
129
154
186
206
226
3.42
6.16
7.52
8.9
11.6
14.4
17.1
18.5
19.8
25.4
29.4
36.2
44.4
52.6
56.8
63.6
77.2
95
116
136
163
180
200
6.34
8.86
11.40
13.9
16.5
21.6
24.0
26.6
29.2
36.8
44.4
54.4
64.6
77.2
Part Number
DRQ125-820-R
DRQ125-101-R
DRQ125-151-R
DRQ125-221-R
DRQ125-331-R
DRQ125-471-R
DRQ125-681-R
DRQ125-821-R
DRQ125-102-R
DRQ127-R47-R
DRQ127-1R0-R
DRQ127-1R5-R
DRQ127-2R2-R
DRQ127-3R3-R
DRQ127-4R7-R
DRQ127-6R8-R
DRQ127-8R2-R
DRQ127-100-R
DRQ127-150-R
DRQ127-220-R
DRQ127-330-R
DRQ127-470-R
DRQ127-680-R
DRQ127-820-R
DRQ127-101-R
DRQ127-151-R
DRQ127-221-R
DRQ127-331-R
DRQ127-471-R
DRQ127-681-R
DRQ127-821-R
DRQ127-102-R
Rated
Inductance
(µH)
82.0
100
150
220
330
470
680
820
1000
0.47
1.00
1.50
2.20
3.30
4.70
6.80
8.20
10.0
15.0
22.0
33.0
47.0
68.0
82.0
100
150
220
330
470
680
820
1000
OCL(1)
+/-20%
(µH)
86.89
102.7
151.1
216.8
332.6
473.1
679.8
828.0
1008
0.419
0.821
1.357
2.027
2.831
4.841
7.387
8.861
10.47
14.09
22.93
33.92
47.05
66.48
79.75
99.31
144.9
221.5
323.6
467.1
676.7
818.1
1005
Irms(2)
Amps
2.05
1.78
1.48
1.19
1.06
0.87
0.70
0.60
0.57
17.9
15.5
13.5
12.5
10.4
8.25
7.34
6.32
6.04
5.03
4.00
3.23
2.95
2.44
2.09
1.96
1.59
1.29
1.04
0.85
0.76
0.65
0.61
Parallel Ratings
Isat(3)
Amps
Peak
2.39
2.20
1.81
1.51
1.22
1.02
0.85
0.77
0.70
56.0
40.0
31.1
25.5
21.5
16.5
13.3
12.2
11.2
9.66
7.57
6.22
5.28
4.44
4.06
3.64
3.01
2.43
2.01
1.68
1.39
1.27
1.14
DCR Ω (4)
typ.
Volt(5)
µ-Sec
0.128
0.170
0.248
0.384
0.482
0.718
1.10
1.49
1.69
0.00195
0.00261
0.00341
0.00373
0.00567
0.00917
0.0116
0.0157
0.0172
0.0247
0.0391
0.0600
0.0719
0.105
0.143
0.163
0.247
0.376
0.574
0.861
1.08
1.47
1.66
43.7
47.5
57.6
69.0
85.5
102
122
135
149
3.50
4.90
6.30
7.70
9.10
11.9
14.7
16.1
17.5
20.3
25.9
31.5
37.1
44.1
48.3
53.9
65.1
80.5
97.3
117
141
155
172
1) Open Circuit Inductance Test Parameters: 100kHz, 0.25 Vrms, 0.0 Adc
Parallel: (1,2 -4,3) Series: (1-4) tie (2-3)
2) RMS current for an approximate ∆T of 40°C without core loss. It is recommended that the
temperature of the part not exceed 125°C.
3) Peak current for approximately 30% roll-off at 20°C
4) DCR limits @ 20°C
5) Applied Volt-Time product (V-µS) across the inductor. This value represents the applied V-µS
at 100KHz necessary to generate a core loss equal to 10% of the total losses for a 40°C
temperature rise.
1207
BU-SB07326
Page 3 of 7
OCL(1)
+/-20%
(µH)
347.6
410.8
604.4
867.2
1330
1892
2719
3312
4032
1.676
3.284
5.428
8.108
11.32
19.36
29.55
35.44
41.88
56.36
91.72
135.7
188.2
265.9
319.0
397.2
579.6
886.0
1294
1868
2707
3272
4020
Irms(2)
Amps
1.03
0.892
0.739
0.594
0.530
0.434
0.350
0.301
0.283
8.94
7.74
6.77
6.23
5.23
4.13
3.67
3.16
3.02
2.51
2.00
1.61
1.47
1.22
1.04
0.980
0.796
0.645
0.522
0.427
0.380
0.325
0.307
Series Ratings
Isat(3)
DCR Ω (4)
Amps
typ.
Peak
1.20
0.515
1.10
0.682
0.905
0.991
0.755
1.54
0.610
1.93
0.510
2.87
0.425
4.42
0.385
5.96
0.350
6.76
28
0.0078
20
0.0104
15.6
0.0137
12.7
0.0161
10.8
0.0229
8.24
0.0367
6.67
0.0465
6.09
0.0627
5.60
0.0686
4.83
0.0990
3.78
0.157
3.11
0.241
2.64
0.288
2.22
0.421
2.03
0.573
1.82
0.653
1.51
0.989
1.22
1.50
1.01
2.30
0.838
3.44
0.697
4.32
0.633
5.88
0.571
6.64
6) Turns Ratio (1:3):(2-4) 1:1
7) Part number definition: DRQxxx-yyy-R
DRQxxx = product code and size,
-yyy = inductance value in µH,
R = decimal point. If no R is present, third character = # of zeros
-R suffix = RoHS compliant
Data Sheet 4311
Volt(5)
µ-Sec
87.4
95.0
115.2
138
171
204
244
270
298
7.00
9.80
12.60
15.4
18.2
23.8
29.4
32.2
35.0
40.6
51.8
63.0
74.2
88.2
96.6
107.8
130.2
161
195
234
282
310
344
Dimensions - mm
DRQ73 Series
Recommended Pad Layout
Side View
Top View
3.55 Max
1.73
1.00
1.00
0.40
0.40
•
DRQ73
###
7.6
Max.
1.73
7.9
7.9
Dual Inductor Mode
Bottom View
Series Mode
Schematic
6.1
0.73
Dual Inductor
0.60
Series Mode
1
7.6
Max.
1
2
L1
0.80
2
L2
3
Parallel Mode
L1
L2
3
4
1
2
L1
L2
3
4
4
DRQ74 Series
Recommended Pad Layout
Side View
Top View
1.73
4.45
Max
•
DRQ74
###
1.00
1.00
0.40
0.40
1.73
7.6
Max
7.9
7.9
Dual Inductor Mode
Series Mode
Bottom View
Schematic
0.73
Dual Inductor
7.6
Max
0.60
1
2
L1
1
L2
L1
4
3
Parallel Mode
Series Mode
3
2
1
4
3
2
L1
L2
L2
4
6.1
Dimensions in millimeters.
1207
BU-SB07326
### = Inductance value per family chart
Dot indicates pin #1
Page 4 of 7
Data Sheet 4311
Dimensions - mm
DRQ125 Series
Side View
Top View
Recommended Pad Layout
6.00 Max
3.85
1
•
1
2
DRQ125
###
wwlly y R
2.50
4
4
2
3
12.5
Max
3
0.50
3.85
2.50
1
4
2
3
0.50
13.80
13.80
Dual Inductor Mode
Series Mode
Bottom View
2.05
Schematic
2.00 2
3
1
4
Dual Inductor
12.5
Max
1
2
L1
1
L2
3
10.0
Parallel Mode
Series Mode
L1
4
2
1
4
3
L1
L2
3
2
L2
4
DRQ127 Series
Side View
Top View
Recommended Pad Layout
8.0
Max
•
1
2
DRQ127
###
wwll yy R
2.50
4
2.50
12.5
Max
3
0.50
3.85
3.85
1
4
2
3
0.50
13.80
13.80
Dual Inductor Mode
Series Mode
Bottom View
2.05
Schematic
2.00 2
3
1
4
Dual Inductor
12.5
Max
1
L1
3
10.0
Series Mode
2
1
4
3
L2
L1
BU-SB07326
2
1
4
3
L2
Dimensions in millimeters.
1207
Parallel Mode
2
L1
L2
4
### = Inductance value per family chart
wwllyy = (date code) R = revision level
Dot indicates pin #1
Page 5 of 7
Data Sheet 4311
Packaging Information
DRQ73 Series
Supplied in tape and reel packaging,
1350 parts per reel, 13" diameter reel.
ACTUAL SIZE
DRQ73
Ao=7.90mm
Bo=7.90mm
Ko=3.80mm
Direction of Feed
➞
DRQ74 Series
Supplied in tape and reel packaging,
1100 parts per reel, 13" diameter reel.
Ø1.50 +0.1/-0.0
2.00 ±0.1
0.1
Ø1.50 Min.
A
4.00
1.75±0.10
1
2
7.50±0.1
DRQ74
###
Bo
ACTUAL SIZE
DRQ74
4
3
A
Ko
Ao=7.90mm
Bo=7.90mm
Ko=4.70mm
16.00
±0.3
0.3
Direction of Feed
12.00
Ao
➞
SECTION A-A
DRQ125 Series
Supplied in tape and reel packaging,
600 parts per reel, 13" diameter reel.
4.0
1.5 dia
+0.1/-0.0
2.0
1.5 dia
min
A
1.7
1
2
11.5
•
ACTUAL SIZE
DRQ125
4
3
Ao=13.00mm
Bo=13.00mm
Ko=6.30mm
24.0
+/-0.3
DRQ125
###
wwllyy
B0
K0
A0
Direction of Feed
A
16.00
➞
SECTION A-A
DRQ127 Series
4.0
Supplied in tape and reel packaging,
350 parts per reel, 13" diameter reel.
1.5 dia
+0.1/-0.0
2.0
1.5 dia
min
A
1.7
R0.3 max.
1
2
11.5
Direction of Feed
K0
A0
20.00
SECTION A-A
A
R0.5 TYP.
Dimensions are in millimeters.
1207
BU-SB07326
ACTUAL SIZE
DRQ127
4
3
Ao=13.00mm
Bo=13.00mm
Ko=8.30mm
24.0
+/-0.3
DRQ127
###
wwllyy
B0
Page 6 of 7
Data Sheet 4311
➞
Inductance Characteristics
OCL vs Isat DRQ73
OCL vs Isat DRQ74
100
100
90
80
80
OCL (%)
OCL (%)
70
60
50
40
60
40
30
20
20
10
0
0
20
40
60
80
100
120
140
0
160
20
0
40
60
80
120
140
160
180
OCL vs Isat DRQ127
OCL vs Isat DRQ125
100
100
90
90
80
80
70
70
OCL (%)
OCL (%)
100
% of Isat
% of Isat
60
50
60
50
40
40
30
30
20
20
10
10
0
0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
0
150
0
10
20
30
40
50
60
% of Isat
70
80
90
100
110
120
130
140
150
% of Isat
50
z
KH
25
KH
z
Hz
0K
10
Hz
0K
30
0K
20
% of Losses from Irms (maximum)
Hz
Irms DERATING WITH CORE LOSS
Core Loss
% of Applied Volt-µSecond
North America
Cooper Bussmann
1225 Broken Sound Parkway NW
Suite F
Boca Raton, FL 33487-3533
Tel: 1-561-998-4100
Fax: 1-561-241-6640
Toll Free: 1-888-414-2645
Cooper Bussmann
P.O. Box 14460
St. Louis, MO 63178-4460
Tel: 1-636-394-2877
Fax: 1-636-527-1607
Europe
Cooper Bussmann
Cooper (UK) Limited
Burton-on-the-Wolds
Leicestershire • LE12 5TH UK
Tel: +44 (0) 1509 882 737
Fax: +44 (0) 1509 882 786
Cooper Bussmann
Avda. Santa Eulalia, 290
08223
Terrassa, (Barcelona), Spain
Tel: +34 937 362 812
+34 937 362 813
Fax: +34 937 362 719
Asia Pacific
Cooper Bussmann
1 Jalan Kilang Timor
#06-01 Pacific Tech Centre
Singapore 159303
Tel: +65 278 6151
Fax: +65 270 4160
This bulletin is intended to present product design solutions and technical information that will help the end user with design applications. Cooper Bussmann reserves the right, without notice,
to change design or construction of any products and to discontinue or limit distribution of any products. Cooper Bussmann also reserves the right to change or update, without notice, any
technical information contained in this bulletin. Once a product has been selected, it should be tested by the user in all possible applications.
Life Support Policy: Cooper Bussmann does not authorize the use of any of its products for use in life support devices or systems without the express written approval of an officer of the
Company. Life support systems are devices which support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling,
can be reasonably expected to result in significant injury to the user.
© 2007 Cooper Bussmann
S t . L o u i s, M O 6 3 1 7 8
w w w. c o o p e r bu s s m a n n . c o m
1207
BU-SB07326
Page 7 of 7
Data Sheet 4311
Similar pages