Cirrus CS3004-FS Precision low-voltage amplifier Datasheet

CS3004
Precision Low-voltage Amplifier
Features & Description
Description
‰
The CS3004 dual amplifier is designed for precision amplification of low-level signals. These amplifiers achieve
excellent offset stability, high open loop gain, and low
noise. The devices also exhibit excellent CMRR and
PSRR. The common mode input range includes the supply rails. The amplifiers operate with any supply voltage
from 2.7 V to 5 V (±1.35 V to ±2.50 V).
Low Offset:
– 10 µV Max.
‰
Low Drift:
– 0.05 µV/°C Max.
‰
Low Noise:
– 17 nV/√Hz
‰
Open-loop Voltage Gain:
– 150 dB Typ.
‰
Rail-to-Rail Inputs
‰ Rail-to-Rail Output Swing
Pin Configurations
– to within 10 mV of supply voltage
‰
‰
CS3004
2.1 mA Supply Current
Slew rate:
– 0.25 V/µs
Out A 1
Applications
‰
‰
‰
‰
Exposed
Thermal
Die Pad2
(Top View)
8 V+
A
- +
-In A 2
Thermocouple/Thermopile Amplifiers
Load Cell and Bridge Transducer Amplifiers
Precision Instrumentation
Battery-powered Systems
7 Out B
B
+ -
+In A 3
V- 4
8 V+
OUT A 1
-IN A 2
6 -In B
+IN A 3
5 +In B
V- 4
8-Lead SOIC
A
– +
Exposed
Thermal
Die Pad
7 OUT B
B
+ –
6 -IN B
5 +IN B
QFN-8
1. Must not be connected.
2. Connect thermal die pad to V-.
1000
200
150
100
100
50
0
-50
10
-100
-150
-200
1
0.01
0.1
1
10
0
1
Frequency (Hz)
3
4
5
6
7
8
9
10
Time (sec)
Noise vs. Frequency (Measured)
Cirrus Logic, Inc.
http://www.cirrus.com
2
0.01 Hz to 10 Hz Noise Performance
Copyright © Cirrus Logic, Inc. 2007
(All Rights Reserved)
AUG ‘07
DS719F1
CS3004
TABLE OF CONTENTS
1. CHARACTERISTICS AND SPECIFICATIONS ............................................. 3
1.1 5 V Electrical Characteristics ................................................................... 3
1.2 3 V Electrical Characteristics ................................................................... 4
1.3 Absolute Maximum Ratings ..................................................................... 5
2. PERFORMANCE PLOTS ............................................................................... 5
3. PACKAGE DRAWINGS ................................................................................. 7
4. ORDERING INFORMATION .......................................................................... 9
5. ENVIRONMENTAL, MANUFACTURING, & HANDLING INFORMATION ... 9
LIST OF FIGURES
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Noise vs Frequency (Measured) .................................................................................5
0.01 Hz to 10 Hz Noise ................................................................................................5
Gain & Phase vs. Frequency (2.7 V)............................................................................5
Gain & Phase vs. Frequency (5 V) ..............................................................................5
Supply Current vs. Supply Voltage ..............................................................................5
Supply Current vs. Temperature .................................................................................5
Voltage Swing vs. Output Current (2.7 V) ...................................................................6
Voltage Swing vs. Output Current (5 V) .......................................................................6
Contacting Cirrus Logic Support
For all product questions and inquiries contact a Cirrus Logic Sales Representative.
To find one nearest you go to http://www.cirrus.com
IMPORTANT NOTICE
Cirrus Logic, Inc. and its subsidiaries ("Cirrus") believe that the information contained in this document is accurate and reliable. However, the information is subject
to change without notice and is provided "AS IS" without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant
information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale
supplied at the time of order acknowledgment, including those pertaining to warranty, indemnification, and limitation of liability. No responsibility is assumed by Cirrus
for the use of this information, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third
parties. This document is the property of Cirrus and by furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights,
copyrights, trademarks, trade secrets or other intellectual property rights. Cirrus owns the copyrights associated with the information contained herein and gives consent for copies to be made of the information only for use within your organization with respect to Cirrus integrated circuits or other products of Cirrus. This consent
does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE
IN AIRCRAFT SYSTEMS, MILITARY APPLICATIONS, PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, AUTOMOTIVE SAFETY OR SECURITY DEVICES, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK AND CIRRUS DISCLAIMS AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED,
INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS PRODUCT
THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOMER'S CUSTOMER USES OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL
APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO FULLY INDEMNIFY CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND
OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING ATTORNEYS' FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION
WITH THESE USES.
Cirrus Logic, Cirrus, and the Cirrus Logic logo designs are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks
or service marks of their respective owners.
2
DS719F1
CS3004
1. CHARACTERISTICS AND SPECIFICATIONS
1.1
5 V Electrical Characteristics
V+ = +5 V, ±5%; V- = 0V; VCM = 2.5 V; Unless otherwise noted, TA = 25º C (See Note 1).
Parameter
Min
Typ
Max
Unit
Input Offset Voltage
(Note 2)
•
-
±2
±10
µV
Average Input Offset Drift
(Note 2)
•
-
±0.01
±0.05
µV/ºC
•
-
±170
-
±250
±1.5
pA
nA
•
-
±340
-
±500
±3.0
pA
nA
-
17
17
-
nV/ Hz
nV/ Hz
Input Bias Current
Input Offset Current
Input Noise Voltage Density
RS = 100 Ω, f0 = 1 Hz
RS = 100 Ω, f0 = 1 kHz
Input Noise Voltage
Input Noise Current Density
Input Noise Current
0.1 to 10 Hz
-
350
-
nVp-p
f0 = 1 Hz
-
100
-
fA/ Hz
0.1 to 10 Hz
-
1.9
•
V-
-
V+
V
Common Mode Rejection Ratio (dc)
•
110
120
-
dB
Power Supply Rejection Ratio
•
110
130
-
dB
RL = 2 kΩ to V+/2
•
120
150
150
-
dB
dB
RL = 2 kΩ to V+/2
(Note 4) RL = 100 kΩ to V+/2
•
(V+ – 100)
(V+ – 10)
-
(V- + 100 )
(V- + 10)
mV
mV
0.25
-
V/µs
25
-
µs
-
2.0
2.5
mA
-
150
-
kHz
-
1.5
10
-
pF
pF
Input Voltage Range
(Note 2)
Large Signal Voltage Gain
(Note 3)
Output Voltage Swing
Slew Rate
RL = 2 k, 100 pF
Overload Recovery Time
-
Supply Current
•
Oscillator Frequency
Input Capacitance
Differential
Common Mode
pAp-p
Notes: 1. Symbol “•” denotes specification applies over -40 to +125 ° C.
2. This parameter is guaranteed by design and/or laboratory characterization.
3. Guaranteed within the output limits of (V+ – 0.2 V) to (V- + 0.2 V).
4. Specifies the worst case drive voltage relative to the supply rail under stated load conditions.
DS719F1
3
CS3004
1.2
3 V Electrical Characteristics
V+ = +3 V, ±10%; V- = 0V; VCM = 1.5 V; Unless otherwise noted, TA = 25º C (See Note 5).
Min
Typ
Max
Unit
Input Offset Voltage
Parameter
(Note 6)
•
-
±2
±10
µV
Average Input Offset Drift
(Note 6)
•
-
±0.01
±0.05
µV/ºC
•
-
±110
-
±150
±1.0
pA
nA
•
-
±220
-
±300
±2.0
pA
nA
RS = 100 Ω, f0 = 1 Hz
RS = 100 Ω, f0 = 1 kHz
-
17
17
-
nV/ Hz
nV/ Hz
0.1 to 10 Hz
-
350
-
nVp-p
f0 = 1 Hz
-
100
-
fA/ Hz
0.1 to 10 Hz
-
1.9
Input Bias Current
Input Offset Current
Input Noise Voltage Density
Input Noise Voltage
Input Noise Current Density
Input Noise Current
Input Voltage Range
(Note 6)
pAp-p
•
V-
-
V+
V
Common Mode Rejection Ratio (dc)
•
110
120
-
dB
Power Supply Rejection Ratio
•
110
130
-
dB
RL = 2 kΩ to V+/2
•
120
160
150
-
dB
dB
RL = 2 kΩ to V+/2
(Note 8) RL = 100 kΩ to V+/2
•
(V+ – 100)
(V+ – 10)
-
(V- + 100 )
(V- + 10)
mV
mV
0.25
-
V/µs
-
25
-
µs
-
2.0
2.5
mA
-
150
-
kHz
-
1.5
10
-
pF
pF
Large Signal Voltage Gain
(Note 7)
Output Voltage Swing
Slew Rate
RL = 2 k, 100 pF
Overload Recovery Time
Supply Current
•
Oscillator Frequency
Input Capacitance
Differential
Common Mode
Notes: 5. Symbol “•” denotes specification applies over -40 to +125 ° C.
6. This parameter is guaranteed by design and/or laboratory characterization.
7. Guaranteed within the output limits of (V+ – 0.2 V) to (V- + 0.2 V).
8. Specifies the worst case drive voltage relative to the supply rail under stated load conditions.
4
DS719F1
CS3004
1.3
Absolute Maximum Ratings
Supply Voltage
Parameter
Min
Typ
Max
Unit
[(V+) – (V-)]
2.7
-
5.5
V
(V-) – 0.3
-
(V+) + 0.3
V
-65
-
+150
ºC
Input Voltage
Storage Temperature Range
2. TYPICAL PERFORMANCE PLOTS
1000
200
150
100
100
50
0
-50
10
-100
-150
1
0.01
0.1
1
-200
10
0
1
2
3
4
Frequency (Hz)
Figure 1. Noise vs Frequency (Measured)
180
160
140
120
100
80
60
40
20
0
-20
0.001 0.01 0.1
1
10
100
1k
5
6
7
8
9
10
Time (sec)
10k 100k 1M
Figure 2. 0.01 Hz to 10 Hz Noise
270
225
180
135
90
45
0
-45
-90
-135
-180
10M
180
160
140
120
100
80
60
40
20
0
-20
0.001 0.01
270
225
180
135
90
45
0
0.1
Frequency (Hz)
1
10
100
1k
10k 100k 1M
-45
-90
-135
-180
10M
Frequency (Hz)
Figure 4. Gain & Phase vs. Frequency (5 V)
Figure 3. Gain & Phase vs. Frequency (2.7 V)
2.5
1.9
Supply Current (mA)
Supply Current (mA)
2.0
1.8
1.7
1.6
1.5
2.5
3
3.5
4
4.5
5
Supply voltage
Figure 5. Supply Current vs. Supply Voltage
DS719F1
5.5
2.0
5V
1.5
2.7V
1.0
0.5
-40
-15
10
35
60
85
110 125
Temperature (°C)
Figure 6. Supply Current vs. Temperature
5
CS3004
Typical Performance Plots (Cont.)
V+
V+
-50
-50
+125°C
-40°C
-150
+25°C
-200
+200
-40°C
+150
+25°C
+125°C
+100
-40°C
-150
+25°C
-200
+200
-40°C
+150
+25°C
+125°C
+100
+50
V–
+125°C
-100
Output Voltage (mV)
Output Voltage (mV)
-100
+50
0
1
2
3
Output Current (mA)
4
V–
5
0
1
2
3
Output Current (mA)
4
5
Figure 8. Voltage Swing vs. Output Current (5 V)
Figure 7. Voltage Swing vs. Output Current (2.7 V)
3. PACKAGE DRAWINGS
8L SOIC (150 MIL BODY) PACKAGE DRAWING
E
H
1
b
c
D
SEATING
PLANE
∝
A
L
e
A1
INCHES
DIM
A
A1
B
C
D
E
e
H
L
∝
MIN
0.053
0.004
0.013
0.007
0.189
0.150
0.040
0.228
0.016
0°
MAX
0.069
0.010
0.020
0.010
0.197
0.157
0.060
0.244
0.050
8°
MILLIMETERS
MIN
MAX
1.35
1.75
0.10
0.25
0.33
0.51
0.19
0.25
4.80
5.00
3.80
4.00
1.02
1.52
5.80
6.20
0.40
1.27
0°
8°
JEDEC # : MS-012
6
DS719F1
CS3004
8L QFN (4 mm X 4 mm) PACKAGE DRAWING
DS719F1
7
CS3004
4. ORDERING INFORMATION
Part #
Temperature Range
Package Description
CS3004-FS
-40 °C to +125 °C
8-lead SOIC
CS3004-FSZ
-40 °C to +125 °C
8-lead SOIC, Lead Free
CS3004-FNZ*
-40 °C to +125 °C
8-lead QFN, Lead Free
* Connect thermal die pad to V-.
5. ENVIRONMENTAL, MANUFACTURING, & HANDLING INFORMATION
Model Number
Peak Reflow Temp
CS3004-FS
240 °C
MSL Rating*
Max Floor Life
2
365 Days
CS3004-FSZ
260 °C
CS3004-FNZ
* MSL (Moisture Sensitivity Level) as specified by IPC/JEDEC J-STD-020.
6. REVISION HISTORY
8
Revision
Date
Changes
PP4
FEB 2007
First public release.
F1
AUG 2007
Updated to “Final” per QPL process.
DS719F1
Similar pages