Exar CLC2005IMP8EVB Low cost, 2.7v to 5.5v, 260mhz rail-to-rail amplifier Datasheet

CLC1005, CLC1015, CLC2005
Low Cost, +2.7V to 5.5V, 260MHz
Rail-to-Rail Amplifiers
FE ATU R E S
■■ 260MHz bandwidth
■■ Fully specified at +2.7V and +5V supplies
■■ Output voltage range:
❏❏ 0.036V to 4.953V; V = +5; R = 2kΩ
S
L
■■ Input voltage range:
❏❏ -0.3V to +3.8V; V = +5
S
■■ 145V/μs slew rate
■■ 4.2mA supply current
■■ Power down to 127μA
■■ ±55mA linear output current
■■ ±85mA short circuit current
■■ CLC2005 directly replaces AD8052/42/92
in single supply applications
■■ CLC1005 directly replaces AD8051/41/91
in single supply applications
General Description
The CLC1005 (single), CLC1015 (single with disable), and CLC2005 (dual)
are low cost, voltage feedback amplifiers. These amplifiers are designed
to operate on +2.7V to +5V, or ±2.5V supplies. The input voltage range
extends 300mV below the negative rail and 1.2V below the positive rail.
The CLC1005, CLC1015, and CLC2005 offer superior dynamic performance
with 260MHz small signal bandwidth and 145V/μs slew rate. The amplifiers
consume only 4.2mA of supply current per channel and the CLC1015 offers
a disable supply current of only 127μA. The combination of low power, high
output current drive, and rail-to-rail performance make these amplifiers well
suited for battery-powered communication/computing systems.
The combination of low cost and high performance make the CLC1005,
CLC1015, and CLC2005 suitable for high volume applications in both
consumer and industrial applications such as interactive whiteboards,
wireless phones, scanners, color copiers, and video transmission.
A P P LICATION S
■■ A/D driver
■■ Active filters
■■ CCD imaging systems
■■ CD/DVD ROM
■■ Coaxial cable drivers
■■ High capacitive load driver
■■ Portable/battery-powered applications
■■ Twisted pair driver
■■ Telecom and optical terminals
■■ Video driver
■■ Interactive whiteboards
Ordering Information - backpage
2nd & 3rd Harmonic Distortion; VS = +2.7V
Output Swing
-20
2.7
Vo = 1Vpp
Rf = 1kΩ
Distortion (dBc)
Output Voltage (0.5V/div)
-30
-50
2nd
RL = 150Ω
-60
2nd
RL = 2kΩ
-70
3rd
RL = 2kΩ
-80
Vs = +2.7V
RL = 2kΩ
G = -1
-90
0
0
5
10
15
20
Frequency (MHz)
Time (0.5μs/div)
© 2007-2015 Exar Corporation 3rd
RL = 150Ω
-40
1 / 19
exar.com/CLC1005
Rev 2D
CLC1005, CLC1015, CLC2005
Absolute Maximum Ratings
Operating Conditions
Stresses beyond the limits listed below may cause
permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect
device reliability and lifetime.
Supply Voltage Range....................................................2.5 to 5.5V
Operating Temperature Range..................................-40°C to 85°C
Junction Temperature............................................................ 150°C
Storage Temperature Range....................................-65°C to 150°C
Lead Temperature (Soldering, 10s).......................................260°C
VS.................................................................................... 0V to +6V
VIN............................................................. -VS - 0.5V to +VS +0.5V
Package Thermal Resistance
θJA (SOIC-8)......................................................................150°C/W
θJA (MSOP-8)................................................................... 200°C/W
θJA (TSOT23-5).................................................................215°C/W
θJA (TSOT23-6).................................................................192°C/W
Package thermal resistance (θJA), JEDEC standard, multi-layer
test boards, still air.
ESD Protection
SOIC-8 (HBM)........................................................................2.5kV
ESD Rating for HBM (Human Body Model) and CDM (Charged
Device Model).
© 2007-2015 Exar Corporation 2 / 19
exar.com/CLC1005
Rev 2D
CLC1005, CLC1015, CLC2005
Electrical Characteristics at +2.7V
TA = 25°C, VS = +2.7V, Rf = 2kΩ, RL = 2kΩ to VS/2; G = 2; unless otherwise noted.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
Frequency Domain Response
GBWP
-3dB Gain Bandwidth Product
86
MHz
UGBW
Unity Gain Bandwidth(1)
G = +1, VOUT = 0.05Vpp
215
MHz
BWSS
-3dB Bandwidth
G = +2, VOUT = 0.2Vpp
85
MHz
BWLS
Large Signal Bandwidth
G = +2, VOUT = 2Vpp
36
MHz
tR, tF
Rise and Fall Time (1)
VOUT = 0.2V step; (10% to 90%)
3.7
ns
tS
Settling Time to 0.1%
VOUT = 1V step
40
ns
OS
Overshoot
VOUT = 0.2V step
9
%
SR
Slew Rate
G = -1, 2.7V step
130
V/μs
Time Domain
Distortion/Noise Response
HD2
2nd Harmonic Distortion (1)
5MHz, VOUT = 1Vpp
79
dBc
HD3
3rd Harmonic Distortion (1)
5MHz, VOUT = 1Vpp
82
dBc
THD
Total Harmonic Distortion
5MHz, VOUT = 1Vpp
77
dB
en
Input Voltage Noise
>1MHz
16
nV/√Hz
in
Input Current Noise
>1MHz
1.3
pA/√Hz
XTALK
Crosstalk
CLC2005, 10MHz
65
dB
(1)
(1)
DC Performance
VIO
Input Offset Voltage
-1.6
mV
dVIO
Average Drift
10
μV/°C
IB
Input Bias Current
3
μA
dIB
Average Drift
7
nA/°C
IOS
Input Offset Current
0.1
μA
PSRR
Power Supply Rejection Ratio
57
dB
AOL
Open Loop Gain
75
dB
IS
Supply Current
3.9
mA
150
ns
DC
52
Disable Characteristics (CLC1015)
TON
Turn On Time
TOFF
Turn Off Time
25
ns
OFFISO
Off Isolation
5MHz, RL = 100Ω
75
dB
ISD
Disable Supply Current
DIS tied to GND
58
100
μA
Input Characteristics
RIN
Input Resistance
4.3
MΩ
CIN
Input Capacitance
1.8
pF
CMIR
Common Mode Input Range
-0.3 to 1.5
V
CMRR
Common Mode Rejection Ratio
87
dB
DC, VCM = 0 to VS - 1.5V
Output Characteristics
RL = 10kΩ to VS / 2
VOUT
Output Swing
RL = 2kΩ to VS / 2
RL = 150Ω to VS / 2
IOUT
Output Current
ISC
Short Circuit Current
VS
Power Supply Operating Range
-40°C to +85°C
VOUT = VS / 2
0.023 to
2.66
0.025 to
2.653
0.065 to
2.55
±55
mA
±50
mA
V
V
V
±85
2.5
2.7
mA
5.5
V
Notes:
1. Rf = 1kΩ was used for optimal performance. (For G = +1, Rf = 0)
© 2007-2015 Exar Corporation 3 / 19
exar.com/CLC1005
Rev 2D
CLC1005, CLC1015, CLC2005
Electrical Characteristics at +5V
TA = 25°C, VS = +5V, Rf = 2kΩ, RL = 2kΩ to VS/2; G = 2; unless otherwise noted.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
Frequency Domain Response
GBWP
-3dB Gain Bandwidth Product
90
MHz
UGBW
Unity Gain Bandwidth(1)
G = +1, VOUT = 0.05Vpp
260
MHz
BWSS
-3dB Bandwidth
G = +2, VOUT = 0.2Vpp
90
MHz
BWLS
Large Signal Bandwidth
G = +2, VOUT = 2Vpp
40
MHz
tR, tF
Rise and Fall Time (1)
VOUT = 0.2V step
3.6
ns
tS
Settling Time to 0.1%
VOUT = 2V step
40
ns
OS
Overshoot
VOUT = 0.2V step
7
%
SR
Slew Rate
G = -1, 5V step
145
V/μs
Time Domain
Distortion/Noise Response
HD2
2nd Harmonic Distortion (1)
5MHz, VOUT = 2Vpp
71
dBc
HD3
3rd Harmonic Distortion (1)
5MHz, VOUT = 2Vpp
78
dBc
THD
Total Harmonic Distortion
5MHz, VOUT = 2Vpp
(1)
70
dB
NTSC (3.85MHz), AC-Coupled, RL = 150Ω
0.06
%
NTSC (3.85MHz), DC-Coupled, RL = 150Ω
0.08
%
NTSC (3.85MHz), AC-Coupled, RL = 150Ω
0.07
°
NTSC (3.85MHz), DC-Coupled, RL = 150Ω
0.06
°
DG
Differential Gain
DP
Differential Phase
en
Input Voltage Noise
>1MHz
16
nV/√Hz
in
Input Current Noise
>1MHz
1.3
pA/√Hz
XTALK
Crosstalk(1)
CLC2005, 10MHz
62
dB
DC Performance
VIO
Input Offset Voltage
dVIO
Average Drift
IB
Input Bias Current
dIB
Average Drift
IOS
Input Offset Current
PSRR
Power Supply Rejection Ratio
AOL
Open Loop Gain
IS
Supply Current
-8
1.4
8
10
-8
3
-0.8
0.1
52
57
8
7
DC
68
μA
nA/°C
0.8
μA
dB
78
4.2
mV
μV/°C
dB
5.2
mA
Disable Characteristics (CLC1015)
TON
Turn On Time
150
TOFF
Turn Off Time
25
ns
ns
OFFISO
Off Isolation
5MHz, RL = 100Ω
75
dB
ISD
Disable Supply Current
DIS tied to GND
127
170
μA
Input Characteristics
RIN
Input Resistance
4.3
MΩ
CIN
Input Capacitance
1.8
pF
CMIR
Common Mode Input Range
-0.3 to
3.8
V
CMRR
Common Mode Rejection Ratio
87
dB
DC, VCM = 0 to VS - 1.5V
© 2007-2015 Exar Corporation 4 / 19
72
exar.com/CLC1005
Rev 2D
CLC1005, CLC1015, CLC2005
Electrical Characteristics at +5V Continued
TA = 25°C, VS = +5V, Rf = 2kΩ, RL = 2kΩ to VS/2; G = 2; unless otherwise noted.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
Output Characteristics
VOUT
Output Swing
RL = 10kΩ to VS / 2
0.027 to
4.97
V
RL = 2kΩ to VS / 2
0.036 to
4.953
V
RL = 150Ω to VS / 2
IOUT
Output Current
ISC
Short Circuit Current
VS
Power Supply Operating Range
0.3
0.12 to
4.8
4.625
V
±55
mA
-40°C to +85°C
±50
mA
VOUT = VS / 2
±85
mA
2.5
5
5.5
V
Notes:
1. Rf = 1kΩ was used for optimal performance. (For G = +1, Rf = 0)
© 2007-2015 Exar Corporation 5 / 19
exar.com/CLC1005
Rev 2D
CLC1005, CLC1015, CLC2005
CLC1005 Pin Configurations
CLC1005 Pin Assignments
TSOT-5
TSOT-5
OUT
1
-Vs
2
+IN
3
5
+
+Vs
4
-IN
SOIC-8
Pin Name
Description
1
OUT
Output
2
-VS
Negative supply
3
+IN
Positive input
4
-IN
Negative input
5
+VS
Positive supply
SOIC-8
NC
1
-IN
2
+IN
3
-Vs
Pin No.
+
4
8
NC
7
+Vs
6
OUT
NC
5
Pin No.
Pin Name
Description
1
NC
No Connect
2
-IN
Negative input
3
+IN
Positive input
4
-VS
Negative supply
5
NC
No Connect
6
OUT
Output
7
+VS
Positive supply
8
NC
No Connect
CLC1015 Pin Configurations
CLC1015 Pin Assignments
TSOT-6
TSOT-6
OUT
1
-Vs
2
+IN
3
+
-
6
+Vs
5
DIS
4
-IN
© 2007-2015 Exar Corporation Pin No.
Pin Name
1
OUT
Output
2
-VS
Negative supply
3
+IN
Positive input
4
-IN
Negative input
5
DIS
Disable pin. Enabled if pin is left open or tied
to +VS, disabled if pin is tied to -VS (which is
GND in a single supply application.)
6
+VS
Positive supply
6 / 19
Description
exar.com/CLC1005
Rev 2D
CLC1005, CLC1015, CLC2005
CLC2005 Pin Configuration
CLC2005 Pin Assignments
SOIC-8 / MSOP-8
SOIC-8 / MSOP-8
OUT1
1
-IN1
2
+IN1
3
-Vs
4
+
+
Pin No.
Pin Name
Description
1
OUT1
8
+Vs
2
-IN1
Negative input, channel 1
7
OUT2
3
+IN1
Positive input, channel 1
4
-IN2
-VS
6
5
+IN2
Positive input, channel 2
+IN2
6
-IN2
Negative input, channel 2
7
OUT2
8
+VS
5
© 2007-2015 Exar Corporation 7 / 19
Output, channel 1
Negative supply
Output, channel 2
Positive supply
exar.com/CLC1005
Rev 2D
CLC1005, CLC1015, CLC2005
Typical Performance Characteristics
TA = 25°C, VS = +5V, RL = 2kΩ to VS/2, G = +2, RF = 2kΩ; unless otherwise noted.
Inverting Frequency Response VS = +5V
Normalized Magnitude (1dB/div)
Normalized Magnitude (2dB/div)
Non-Inverting Frequency Response VS = +5V
G=1
Rf = 0
G=2
Rf = 1kΩ
G = 10
Rf = 2kΩ
G=5
Rf = 2kΩ
0.1
1
10
G = -1
Rf = 2kΩ
G = -10
Rf = 2kΩ
G = -5
Rf = 2kΩ
G = -2
Rf = 2kΩ
0.1
100
1
10
100
Non-Inverting Frequency Response VS = +2.7V
Inverting Frequency Response VS = +2.7V
Normalized Magnitude (1dB/div)
Frequency (MHz)
Normalized Magnitude (2dB/div)
Frequency (MHz)
G=1
Rf = 0
G=2
Rf = 1kΩ
G = 10
Rf = 2kΩ
G=5
Rf = 2kΩ
1
0.1
10
G = -1
Rf = 2kΩ
G = -10
Rf = 2kΩ
G = -5
Rf = 2kΩ
G = -2
Rf = 2kΩ
0.1
100
1
10
100
Frequency (MHz)
Frequency (MHz)
Magnitude (1dB/div)
Magnitude (1dB/div)
Frequency Response vs CL
Large Signal Frequency Response
CL = 100pF
Rs = 25Ω
CL = 50pF
Rs = 33Ω
+
-
CL
1kW
1kW
0.1
CL = 20pF
Rs = 20Ω
Rs
1
RL
CL = 10pF
Rs = 0Ω
10
100
Vo = 2Vpp
0.1
Frequency (MHz)
© 2007-2015 Exar Corporation Vo = 1Vpp
1
10
100
Frequency (MHz)
8 / 19
exar.com/CLC1005
Rev 2D
CLC1005, CLC1015, CLC2005
Typical Performance Characteristics
TA = 25°C, VS = +5V, RL = 2kΩ to VS/2, G = +2, RF = 2kΩ; unless otherwise noted.
Frequency Response vs. Temperature
Input Voltage Noise vs Frequency
100
Magnitude (0.5dB/div)
Voltage Noise (nV/√Hz)
90
80
70
60
50
40
30
20
10
1
10
0
100
1k
10k
2nd & 3rd Harmonic Distortion VS = +5V
-30
Distortion (dBc)
-20
Vo = 2Vpp
Rf = 1kΩ
2nd
RL = 150Ω
-40
3rd
RL = 150Ω
-60
2nd
RL = 2kΩ
3rd
RL = 2kΩ
-80
Vo = 1Vpp
Rf = 1kΩ
-30
-50
-70
3rd
RL = 150Ω
-40
-50
2nd
RL = 150Ω
-60
2nd
RL = 2kΩ
-70
3rd
RL = 2kΩ
-80
-90
-90
0
5
10
15
0
20
5
Frequency (MHz)
-20
Rf = 1kΩ
20
2.0
2.5
Rf = 1kΩ
-30
-50
Distortion (dBc)
20MHz
-40
10MHz
-60
-70
5MHz
-80
2MHz
20MHz
-40
-50
10MHz
-60
-70
5MHz
-80
-90
2MHz
-90
0.5
15
3rd Harmonic Distortion vs VO
-20
-30
10
Frequency (MHz)
2nd Harmonic Distortion vs VO Distortion (dBc)
1M
2nd & 3rd Harmonic Distortion VS = +2.7V
Distortion (dBc)
-20
100k
Frequency (Hz)
Frequency (MHz)
1.0
1.5
2.0
2.5
0.5
Output Amplitude (Vpp)
© 2007-2015 Exar Corporation 1.0
1.5
Output Amplitude (Vpp)
9 / 19
exar.com/CLC1005
Rev 2D
CLC1005, CLC1015, CLC2005
Typical Performance Characteristics
TA = 25°C, VS = +5V, RL = 2kΩ to VS/2, G = +2, RF = 2kΩ; unless otherwise noted.
PSRR
CMRR
-40
0
-10
-50
CMRR (dB)
PSRR (dB)
-20
-30
-40
-60
-70
-50
-80
-60
-90
-70
1k
0.01
0.1
1
10
0.01
100
0.1
Frequency (MHz)
80
0.8
70
0.6
|Gain|
40
30
10
0
Phase
-45
Output Voltage (V)
60
20
-90
0
Linear output current ±55mA
0.2
0
-0.2
Short circuit current ±85mA
-0.4
-135
-0.6
-20
-180
-0.8
-100
0.1
1
10
100
Frequency (MHz)
Small Signal Pulse Response VS = +5V 0
50
100
Small Signal Pulse Response VS = +2.7V
Rf = 1kΩ
Time (20ns/div)
© 2007-2015 Exar Corporation -50
Output Current (mA)
Output Voltage (0.05V/div)
Output Voltage (0.05V/div)
100
0.4
-10
0.01
10
Output Current
Phase (degrees)
Open Loop Gain (dB)
Open Loop Gain & Phase vs. Frequency
50
1.0
Frequency (MHz)
Rf = 1kΩ
Time (20ns/div)
10 / 19
exar.com/CLC1005
Rev 2D
CLC1005, CLC1015, CLC2005
Typical Performance Characteristics
TA = 25°C, VS = +5V, RL = 2kΩ to VS/2, G = +2, RF = 2kΩ; unless otherwise noted.
Large Signal Pulse Response VS = +5V
Output Swing
Output Voltage (0.5V/div)
Output Voltage (0.5V/div)
2.7
Rf = 1kΩ
Vs = +2.7V
RL = 2kΩ
G = -1
0
Time (20ns/div)
Time (0.5μs/div)
Channel Matching VS = +5V
Magnitude (0.5dB/div)
Rf = 1kΩ
RL = 2kΩ
G=2
Channel 1
Channel 2
0.1
1
10
100
Frequency (MHz)
© 2007-2015 Exar Corporation 11 / 19
exar.com/CLC1005
Rev 2D
CLC1005, CLC1015, CLC2005
Application Information
+Vs
General Description
The CLC1005, CLC1015, and CLC2005 are single supply,
general purpose, voltage-feedback amplifiers fabricated
on a complementary bipolar process using a patented
topography. They feature a rail-to-rail output stage and are
unity gain stable. Both gain bandwidth and slew rate are
insensitive to temperature.
Input
0.1μF
+
Output
RL
0.1μF
The common mode input range extends to 300mV below
ground and to 1.2V below Vs. Exceeding these values will
not cause phase reversal. However, if the input voltage
exceeds the rails by more than 0.5V, the input ESD devices
will begin to conduct. The output will stay at the rail during
this overdrive condition.
6.8μF
G=1
-Vs
Figure 3: Unity Gain Circuit
+Vs
The design is short circuit protected and offers “soft”
saturation protection that improves recovery time.
6.8μF
+
Figures 1, 2, and 3 illustrate typical circuit configurations for
non-inverting, inverting, and unity gain topologies for dual
supply applications. They show the recommended bypass
capacitor values and overall closed loop gain equations. Figure
4 shows the typical non-inverting gain circuit for single supply
applications.
+Vs
6.8μF
In
0.1μF
+
Out
-
Rf
Rg
6.8μF
Figure 4: Single Supply Non-Inverting Gain Circuit
Input
0.1μF
+
Output
RL
0.1μF
Rg
6.8μF
-Vs
Rf
At non-inverting gains other than G = +1, keep Rg below 1kΩ
to minimize peaking; thus for optimum response at a gain of
+2, a feedback resistor of 1kΩ is recommended. Figure 5
illustrates the CLC1005, CLC1015 and CLC2005 frequency
response with both 1kΩ and 2kΩ feedback resistors.
G = 1 + (Rf/Rg)
Figure 1: Typical Non-Inverting Gain Circuit
R1
Input
Rg
Magnitude (1dB/div)
+Vs
6.8μF
0.1μF
+
G=2
RL = 2kΩ
Vs = +5V
Output
Rf = 2kΩ
Rf = 1kΩ
RL
0.1μF
6.8μF
-Vs
Rf
1
10
100
Frequency (MHz)
G = - (Rf/Rg)
Figure 5: Frequency Response vs. Rf
For optimum input offset
voltage set R1 = Rf || Rg
Figure 2: Typical Inverting Gain Circuit
© 2007-2015 Exar Corporation 12 / 19
exar.com/CLC1005
Rev 2D
CLC1005, CLC1015, CLC2005
Overdrive Recovery
For an amplifier, an overdrive condition occurs when the
output and/or input ranges are exceeded. The recovery time
varies based on whether the input or output is overdriven
and by how much the ranges are exceeded. The CLC1005,
CLC1015, and CLC2005 will typically recover in less than
20ns from an overdrive condition. Figure 6 shows the
CLC2005 in an overdriven condition.
needs to be subtracted from the total power delivered by the
supplies.
PD = Psupply - Pload
Supply power is calculated by the standard power equation.
Psupply = Vsupply × IRMSsupply
Vsupply = VS+ - VS-
Input Voltage (0.5V/div)
Power delivered to a purely resistive load is:
RL = 2kΩ
Vin =2Vpp
G=5
Rf = 1kΩ
Input
Output
Pload = ((Vload)RMS2)/Rloadeff
The effective load resistor (Rloadeff) will need to include the
effect of the feedback network. For instance,
Rloadeff in Figure 3 would be calculated as:
RL || (Rf + Rg)
Time (20ns/div)
These measurements are basic and are relatively easy to
perform with standard lab equipment. For design purposes
however, prior knowledge of actual signal levels and load
impedance is needed to determine the dissipated power.
Here, PD can be found from
Figure 6: Overdrive Recovery
PD = PQuiescent + PDynamic - Pload
Enable/Disable Function
The CLC1015 offers an active-low disable pin that can be
used to lower its supply current. Leave the pin floating to
enable to part. Pull the disable pin to the negative supply
(which is ground in a single supply application) to disable
the output. During the disable condition, the nominal supply
current will drop below 127μA and the output will be at a
high impedance with about 2pF capacitance.
Quiescent power can be derived from the specified IS values
along with known supply voltage, Vsupply. Load power can
be calculated as above with the desired signal amplitudes
using:
(Vload)RMS = Vpeak / √2
( Iload)RMS = ( Vload)RMS / Rloadeff
The dynamic power is focused primarily within the output
stage driving the load. This value can be calculated as:
Power Dissipation
Power dissipation should not be a factor when operating
under the stated 2kΩ load condition. However, applications
with low impedance, DC coupled loads should be analyzed
to ensure that maximum allowed junction temperature is
not exceeded. Guidelines listed below can be used to verify
that the particular application will not cause the device to
operate beyond it’s intended operating range.
Maximum power levels are set by the absolute maximum
junction rating of 150°C. To calculate the junction
temperature, the package thermal resistance value ThetaJA
(θJA) is used along with the total die power dissipation.
PDynamic = (VS+ - Vload)RMS × ( Iload)RMS
Assuming the load is referenced in the middle of the power
rails or Vsupply/2.
The CLC1015 is short circuit protected. However, this may
not guarantee that the maximum junction temperature
(+150°C) is not exceeded under all conditions. Figure 7
shows the maximum safe power dissipation in the package
vs. the ambient temperature for the packages available.
TJunction = TAmbient + (θJA × PD)
Where TAmbient is the temperature of the working
environment.
In order to determine PD, the power dissipated in the load
© 2007-2015 Exar Corporation 13 / 19
exar.com/CLC1005
Rev 2D
CLC1005, CLC1015, CLC2005
Layout Considerations
Maximum Power Dissipation (W)
1.5
General layout and supply bypassing play major roles in
high frequency performance. Exar has evaluation boards to
use as a guide for high frequency layout and as an aid in
device testing and characterization. Follow the steps below
as a basis for high frequency layout:
SOIC-8
1
TSOT-6
■■
MSOP-8
0.5
TSOT-5
■■
Place the 6.8µF capacitor within 0.75 inches of the power pin
■■
Place the 0.1µF capacitor within 0.1 inches of the power pin
■■
0
-40
-20
0
20
40
60
80
Ambient Temperature (°C)
■■
Figure 7. Maximum Power Derating
Include 6.8µF and 0.1µF ceramic capacitors for power supply
decoupling
Remove the ground plane under and around the part,
especially near the input and output pins to reduce parasitic
capacitance
Minimize all trace lengths to reduce series inductances
Refer to the evaluation board layouts below for more
information.
Driving Capacitive Loads
Increased phase delay at the output due to capacitive loading
can cause ringing, peaking in the frequency response, and
possible unstable behavior. Use a series resistance, RS,
between the amplifier and the load to help improve stability
and settling performance. Refer to Figure 8.
Evaluation Board Information
The following evaluation boards are available to aid in the
testing and layout of these devices:
Evaluation Board #
Input
+
Rs
Rf
Output
CL
RL
Products
CEB002
CLC1005 and CLC1015 in TSOT
CEB003
CLC1005 in SOIC
CEB006
CLC2005 in SOIC
CEB010
CLC2005 in MSOP
Rg
Figure 8. Addition of RS for Driving Capacitive Loads
Table 1 provides the recommended RS for various capacitive
loads. The recommended RS values result in approximately
<1dB peaking in the frequency response.
Evaluation Board Schematics
Evaluation board schematics and layouts are shown in
Figures 9-18. These evaluation boards are built for dualsupply operation. Follow these steps to use the board in a
single-supply application:
1. Short -VS to ground.
2. Use C3 and C4, if the -VS pin of the amplifier is not
directly connected to the ground plane.
CL (pF)
RS (Ω)
-3dB BW (MHz)
22pF
0
118
47pF
15
112
100pF
15
91
492pF
6.5
59
Table 1: Recommended RS vs. CL
For a given load capacitance, adjust RS to optimize the
tradeoff between settling time and bandwidth. In general,
reducing RS will increase bandwidth at the expense of
additional overshoot and ringing.
© 2007-2015 Exar Corporation 14 / 19
exar.com/CLC1005
Rev 2D
CLC1005, CLC1015, CLC2005
Figure 11. CEB002 Bottom View
Figure 9. CEB002 and CEB003 Schematic
Figure 12. CEB003 Top View
Figure 10. CEB002 Top View
Figure 13. CEB003 Bottom View
© 2007-2015 Exar Corporation 15 / 19
exar.com/CLC1005
Rev 2D
CLC1005, CLC1015, CLC2005
Figure 16. CEB006 Bottom View
Figure 14. CEB006 & CEB010 Schematic
Figure 17. CEB010 Top View
Figure 15. CEB006 Top View
Figure 18. CEB010 Bottom View
© 2007-2015 Exar Corporation 16 / 19
exar.com/CLC1005
Rev 2D
CLC1005, CLC1015, CLC2005
Mechanical Dimensions
TSOT-6 Package
TSOT-5 Package
© 2007-2015 Exar Corporation 17 / 19
exar.com/CLC1005
Rev 2D
CLC1005, CLC1015, CLC2005
MSOP-8 Package
SOIC-8 Package
© 2007-2015 Exar Corporation 18 / 19
exar.com/CLC1005
Rev 2D
CLC1005, CLC1015, CLC2005
Ordering Information
Part Number
Package
Green
Operating Temperature Range
Packaging
CLC1005IST5X
TSOT-5
Yes
-40°C to +85°C
Tape & Reel
CLC1005IST5MTR
TSOT-5
Yes
-40°C to +85°C
Mini Tape & Reel
CLC1005IST5EVB
Evaluation Board
N/A
N/A
N/A
CLC1005ISO8X
SOIC-8
Yes
-40°C to +85°C
Tape & Reel
CLC1005ISO8MTR
SOIC-8
Yes
-40°C to +85°C
Mini Tape & Reel
CLC1005ISO8EVB
Evaluation Board
N/A
N/A
N/A
CLC1015IST6X
TSOT-6
Yes
-40°C to +85°C
Tape & Reel
CLC1015IST6MTR
TSOT-6
Yes
-40°C to +85°C
Mini Tape & Reel
CLC1015IST6EVB
Evaluation Board
N/A
N/A
N/A
CLC2005ISO8X
SOIC-8
Yes
-40°C to +85°C
Tape & Reel
CLC2005ISO8MTR
SOIC-8
Yes
-40°C to +85°C
Mini Tape & Reel
CLC2005ISO8EVB
Evaluation Board
N/A
N/A
N/A
CLC2005IMP8X
MSOP-8
Yes
-40°C to +85°C
Tape & Reel
CLC2005IMP8MTR
MSOP-8
Yes
-40°C to +85°C
Mini Tape & Reel
CLC2005IMP8EVB
Evaluation Board
N/A
N/A
N/A
CLC1005 Ordering Information
CLC1015 Ordering Information
CLC2005 Ordering Information
Moisture sensitivity level for all parts is MSL-1. Mini tape and reel quantity is 250.
Revision History
Revision
2D (ECN 1513-01)
Date
March 2015
Description
Reformat into Exar data sheet template. Updated ordering information table to include MTR and EVB
part numbers. Updated thermal resistance numbers and package outline drawings. Added CLC1015
back into data sheet.
For Further Assistance:
Email: [email protected] or [email protected]
Exar Technical Documentation: http://www.exar.com/techdoc/
Exar Corporation Headquarters and Sales Offices
48760 Kato Road
Tel.: +1 (510) 668-7000
Fremont, CA 94538 - USA
Fax: +1 (510) 668-7001
NOTICE
EXAR Corporation reserves the right to make changes to the products contained in this publication in order to improve design, performance or reliability. EXAR Corporation
assumes no responsibility for the use of any circuits described herein, conveys no license under any patent or other right, and makes no representation that the circuits are free
of patent infringement. Charts and schedules contained here in are only for illustration purposes and may vary depending upon a user’s specific application. While the information
in this publication has been carefully checked; no responsibility, however, is assumed for inaccuracies.
EXAR Corporation does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected
to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless EXAR Corporation
receives, in writing, assurances to its satisfaction that: (a) the risk of injury or damage has been minimized; (b) the user assumes all such risks; (c) potential liability of EXAR
Corporation is adequately protected under the circumstances.
Reproduction, in part or whole, without the prior written consent of EXAR Corporation is prohibited.
© 2007-2015 Exar Corporation 19 / 19
exar.com/CLC1005
Rev 2D
Similar pages