Chip Varistors Countermeasure for surge voltage and static electricity AVR series Type: AVR-M AVRL Issue date: September 2011 • All specifications are subject to change without notice. • Conformity to RoHS Directive: This means that, in conformity with EU Directive 2002/95/EC, lead, cadmium, mercury, hexavalent chromium, and specific bromine-based flame retardants, PBB and PBDE, have not been used, except for exempted applications. (1/10) Conformity to RoHS Directive Varistors(SMD) Countermeasure for Surge Voltage and Static Electricity AVR Series AVR-M, AVRL Types Varistors are voltage dependent nonlinear resistive elements with a resistance that decreases rapidly when the voltage is over the constant value. Varistor is equivalent with Zener diode of two series connection. Therefore, do not have polarity. CURRENT vs. VOLTAGE CHARACTERISTICS EQUIVALENT CIRCUIT 2 Zener Diodes Current(A) 10–1 10–2 Zener diode /Vz:6.8V Positive direction 10–3 Chip varistor /V1mA:12V 10–4 A capacitance content 10–5 –18 –14 –10 –6 –2 2 –10–5 6 10 14 18 –10–4 –10–3 Negative direction –10–2 –10–1 Voltage(V) THE EFFECT OF THE VARISTOR WITHOUT VARISTOR A malfunction and failure of electronic equipment ESD, Surge voltage ESD, Surge voltage Power line Signal line WITH VARISTOR Suppress abnormal voltage by inserting varistor in a circuit IC Power line Signal line IC Insert a varistor between a line and ground : Chip varistor • All specifications are subject to change without notice. 001-07 / 20110926 / e9c11_avr.fm (2/10) FEATURES • No polarity, due to symmetrical current-voltage characteristics. Equivalent to anode common type Zener diode. • Excellent electrostatic absorption capability. Response is as good or better than Zener diode. Keeps symmetrical current-voltage characteristics even after electrostatic absorption. • Adopted the inner electrodes lamination structure. Wide range of varistor voltages are available in series (6.8 to 39V). Low capacitance items are available in series (1.1pF to). World’s smallest 0603-, 1005-, 1608-, 2012-chip types and 1410-array type are available in series. • Excellent mount reliability. Good for Pb-free soldering. Adopted (Ni/Sn) electroplating. Achieved good solderability and solder heat resistance. • Can replace a Zener diode + capacitor combination. Reduced footprint and total mounting cost. INTERNAL STRUCTURE Inner electrode Varistor body (Palladium) (Zinc Oxide: ZnO semiconductor ceramics) Sn plating Ag termination underlayer Ni plating CIRCUITS SINGLE TYPE ARRAY TYPE OPERATIONAL VOLTAGE RANGES 0603 type 7.5 1005 type APPLICATIONS • Electrostatic absorption • Pulse noise absorption 19 28 1608 type 2012 type 28 1410 type 0 16 5 10 15 20 Circuit voltage(V) TEMPERATURE RANGES Type Operating Storage AVR-M1005/1608/2012 –40 to +125°C –40 to +125°C AVR-M14A2/0603/AVRL –40 to +85°C –40 to +85°C Mobile phone Digital video camera Digital camera PDA Note PC DVD-ROM, CD-ROM CD/MD/MP3 player Game machine In-car equipment Application Data terminal LCD panel Touch panel Button and switch unit Battery terminal Audio-Video input-output terminal Microphone/receiver unit Controller unit CAN-BUS ECU Connector Air conditioner panel Car audio Car navigation 30 RECOMMENDED REFLOW SOLDERING CONDITIONS APPLICATION EXAMPLES Consumer product 25 10s max. 260˚C max. 250˚C 220˚C Natural cooling 180˚C 150˚C Preheating 60 to 120s Soldering 60s max. Time(s) • All specifications are subject to change without notice. 001-07 / 20110926 / e9c11_avr.fm (3/10) AVR-M TYPE PRODUCT IDENTIFICATION AVR-M 1005 C 270 M T AAB (1) (2) (3) (4) (5) (6) (7) SHAPES AND DIMENSIONS/RECOMMENDED PC BOARD PATTERN 0603/1005/1608/2012 TYPES L W (1) Series name 0603 1005 1608 2012 14A2 0.6×0.3mm 1.0×0.5mm 1.6×0.8mm 2.0×1.2mm 1.4×1.0mm (2-element) B T (2) Dimensions L×W Dimensions in mm (3) Structure code (4) Varistor voltage 270 27×100V Type L W T B min. 0603 1005 1608 2012 0.6±0.03 1.0±0.05 1.6±0.1 2.0±0.2 0.3±0.03 0.5±0.05 0.8±0.1 1.25±0.2 0.3±0.03 0.5±0.05 0.8±0.1 1.0±0.2 0.1 0.1 0.2 0.2 Weight (mg)typ. 0.2 1.2 5 15 (5) Varistor voltage tolerance ±10% ±20% c K M b a b (6) Packaging style T B Dimensions in mm Taping Bulk (7) Capacitance and TDK internal code Type 0603 1005 1608 2012 a 0.25 to 0.35 0.3 to 0.5 0.6 to 0.8 0.9 to 1.2 b 0.2 to 0.3 0.35 to 0.45 0.6 to 0.8 0.7 to 0.9 c 0.25 to 0.35 0.4 to 0.6 0.6 to 0.8 0.9 to 1.2 1410 TYPE 1.0±0.2 0.2typ. 1.37±0.2 0.6max. 0.36±0.2 Weight: 4mg typ. 0.32±0.2 0.64typ. 1.0 to 1.4 0.65 to 0.95 0.35 to 0.45 Dimensions in mm 0.6 to 0.66 0.3 to 0.4 Dimensions in mm • All specifications are subject to change without notice. 001-07 / 20110926 / e9c11_avr.fm (4/10) ELECTRICAL CHARACTERISTICS Varistor voltage (Breakdown voltage) V1mA(V)[DC1mA] Maximum continuous voltage (Rated voltage) Vdc(V) Clamping voltage Vcl(V) [8/20µs] Maximum energy E(Joule) [10/1000µs] Maximum peak current Ip(A) [8/20µs] ∗101N 101N 101N AAB 6.8 8 12.8 12 (4.76 to 8.84) (6.4 to 9.6) (10 to 15.6) (9.6 to 14.4) 3.5 max. 5.5 max. 5.5 max. 7.5 max. 14[1A] 17[1A] 20[1A] 23[1A] 0.01 max. 0.01 max. 0.01 max. 0.01 max. 10 max. 4 max. 5 max. 1 max. 100 typ. 100 typ. 100 typ. 33 typ. 15,000 101N AAB ADB ABB ACB AAB 101N AAB ABB 6.8 8 8 8 8 12 27 27 27 (4.76 to 8.84) (6.4 to 9.6) (6.4 to 9.6) (6.4 to 9.6) (6.4 to 9.6) (9.6 to 14.4) (24 to 30) (21.6 to 32.4) (21.6 to 32.4) 3.5 max. 5.5 max. 5.5 max. 5.5 max. 5.5 max. 7.5 max. 19 max. 15 max. 15 max. 14[1A] 14[1A] 14[1A] 15[1A] 19[1A] 20[1A] 55[1A] 50[1A] 50[1A] 0.02 max. 0.04 max. 0.04 max. 0.02 max. 0.01 max. 0.05 max. 0.06 max. 0.06 max. 0.05 max. 10 max. 25 max. 25 max. 3 max. 1 max. 10 max. 4 max. 4 max. 1 max. 100 typ. 650 typ. 480 typ. 100 typ. 33 typ. 130 typ. 100 typ. 40 typ. 15 typ. 10,000 AAB 6AB 2AB 6AB 6AB 2AB 6AB 2AB ACB AAB ABB 271N 8 12 12 18 22 22 27 27 27 27 27 39 (6.4 to 9.6) (9.6 to 14.4) (9.6 to 14.4) (14.4 to 21.6) (19.8 to 24.2) (19.8 to 24.2) (24 to 30) (24 to 30) (24 to 30) (21.6 to 32.4) (21.6 to 32.4) (35 to 43) 5.5 max. 7.5 max. 7.5 max. 11 max. 16 max. 16 max. 19 max. 19 max. 19 max. 17 max. 17 max. 28 max. 15[2A] 20[2A] 20[2A] 30[2A] 34[2A] 37[2A] 42[2A] 42[2A] 54[2A] 52[2A] 52[2A] 69[2A] 0.09 max. 0.09 max. 0.06 max. 0.1 max. 0.1 max. 0.03 max. 0.1 max. 0.1 max. 0.05 max. 0.05 max. 0.05 max. 0.1 max. 30 max. 50 max. 15 max. 30 max. 30 max. 10 max. 48 max. 20 max. 10 max. 2 max. 2 max. 78 max. 650 typ. 1050 typ. 400 typ. 600 typ. 560 typ. 210 typ. 430 typ. 160 typ. 60 typ. 30 typ. 15 typ. 270 typ. 4,000 6AB 6AB 6AB 12 22 39 (9.6 to 14.4) 7.5 max. (19.8 to 24.2) 16 max. (35 to 43) 28 max. 20[5A] 38[5A] 62[5A] 0.2 max. 0.3 max. 0.3 max. 60 max. 100 max. 100 max. 1000 typ. 800 typ. 430 typ. 2,000 600N 470N 150N 3R3F 24 27 27 27 (20 to 27) (21.6 to 32.4) (21.6 to 32.4) (21.6 to 32.4) 50[1A] 54[1A] 55[1A] 45[0.2A] 0.01 max. 0.007 max. 0.02 max. 0.002 max. 5 max. 5 max. 3 max. 0.2 max. 60 typ.[1MHz] 47 typ.[1MHz] 15 typ.[1MHz] 3.3 typ.[1MHz] 4,000 Part No. 0603 type AVRM0603C6R8N AVRM0603C080M AVRM0603C120M AVR-M0603C120M 1005 type AVRM1005C6R8N AVR-M1005C080M AVR-M1005C080M AVR-M1005C080M AVR-M1005C080M AVR-M1005C120M AVRM1005C270K AVR-M1005C270M AVR-M1005C270M 1608 type AVR-M1608C080M AVR-M1608C120M AVR-M1608C120M AVR-M1608C180M AVR-M1608C220K AVR-M1608C220K AVR-M1608C270K AVR-M1608C270K AVR-M1608C270K AVR-M1608C270M AVR-M1608C270M AVRM1608C390K 2012 type AVR-M2012C120M AVR-M2012C220K AVR-M2012C390K 1410 type AVR-M14A2C240M AVR-M14A2C270M AVRM14A2C270M AVRM14A2C270M ∗ 16 max. 15 max. 15 max. 10 max. Capacitance C(pF) [1kHz, 1Vrms] Packaging quantities (Taping) (pieces/reel) : Packaging style(T: Taping/B: Bulk) TERMINOLOGY Clamping voltage Maximum energy Maximum peak current Capacitance Terminology Voltage measured across the varistor when DC1mA is applied. Maximum DC voltage that can be applied continuously. Vdc Varistor leakage current: 50µA max. (V) (Within the range of maximum allowable circuit voltage) Voltage appearing across the varistor Vcl when a pulse current (8/20µs∗1) of (V) specified peak value is applied. Maximum energy that can be absorbed E without deteriorating varistor (Joule) characteristics when an impulse (10/1000µs∗2) is applied once. Maximum current that can be withstood Ip without deteriorating varistor (A) characteristics when an impulse current (8/20µs∗1) is applied once. Capacitance measured at 1kHz C (or 1MHz) of oscillator frequency and (pF) 1Vrms of oscillator voltage. ∗1 8/20µs test waveform 100% 90% Current Maximum continuous voltage (Rated voltage) Unit V1mA (V) 50% 8µs 20µs Time ∗2 10/1000µs test waveform 100% 90% Energy Item Varistor voltage (Breakdown voltage) 50% 10µs 1000µs Time • All specifications are subject to change without notice. 001-07 / 20110926 / e9c11_avr.fm (5/10) AVRL TYPE PRODUCT IDENTIFICATION SHAPES AND DIMENSIONS/RECOMMENDED PC BOARD PATTERN AVRL 10 1A 3R3 F T A (1) (2) (3) (4) (5) (6) (7) L W (1) Series name (2) Dimensions L×W B 1.0×0.5mm 1.6×0.8mm T 10 16 (3) Maximum continuous voltage 1A Dimensions in mm 10Vdc (4) Capacitance 1.1pF 3.3pF 6.8pF L W T B min. 1005 1608 1.0±0.05 1.6±0.1 0.5±0.05 0.8±0.1 0.5±0.05 0.8±0.1 0.1 0.2 Weight (mg)typ. 1.2 5 c 1R1 3R3 6R8 Type (5) Capacitance tolerance N F G ±0.3pF ±1pF ±2pF b b Dimensions in mm Type 1005 1608 (6) Packaging style T B a a 0.3 to 0.5 0.6 to 0.8 b 0.35 to 0.45 0.6 to 0.8 c 0.4 to 0.6 0.6 to 0.8 Taping Bulk (7) Varistor voltage and TDK internal code ELECTRICAL CHARACTERISTICS Capacitance C(pF) [1MHz, 1Vrms] Maximum continuous voltage (Rated voltage) Vdc(V) Insulation resistance Rdc(MΩ) [3Vrms] Varistor voltage V1mA(V)[DC1mA] Packaging quantities (Taping) (pieces/reel) ∗A B A A A 1.1[0.8 to 1.4] 1.1[0.8 to 1.4] 2.2[1.7 to 2.7] 3.3[2.3 to 4.3] 6.8[4.8 to 8.8] 10 max. 10 max. 16 max. 10 max. 10 max. 10 min. 10 min. 10 min. 10 min. 10 min. 90 typ. 39 typ. 90 typ. 27 typ. 27 typ. 10,000 A B A A 1.1[0.8 to 1.4] 1.1[0.8 to 1.4] 3.3[2.3 to 4.3] 6.8[4.8 to 8.8] 10 max. 10 max. 10 max. 10 max. 10 min. 10 min. 10 min. 10 min. 90 typ. 39 typ. 27 typ. 27 typ. 4,000 Part No. 1005 type AVRL101A1R1N AVRL101A1R1N AVRL101C2R2D AVRL101A3R3F AVRL101A6R8G 1608 type AVRL161A1R1N AVRL161A1R1N AVRL161A3R3F AVRL161A6R8G ∗ : Packaging style(T: Taping/B: Bulk) TERMINOLOGY Item Capacitance Maximum continuous voltage (Rated voltage) Insulation resistance Varistor voltage (Breakdown voltage) Unit C (pF) Vdc (V) Rdc (MΩ ) V1mA (V) Terminology Capacitance measured at 1MHz of oscillator frequency and 1Vrms of oscillator voltage. Maximum DC voltage that can be applied continuously. Varistor leakage current: 50µA max. (Within the range of maximum allowable circuit voltage) Insulation resistance appearing across the varistor when specified voltage is applied. Voltage measured across the varistor when DC1mA is applied. • All specifications are subject to change without notice. 001-07 / 20110926 / e9c11_avr.fm (6/10) TYPICAL ELECTRICAL CHARACTERISTICS CURRENT vs. VOLTAGE CHARACTERISTICS IMPEDANCE vs. FREQUENCY CHARACTERISTICS 10000 100 15pF 6.8pF 3.3pF V1mA:12V 10–1 1000 30pF V1mA:8V Impeadance(Ω) Current(A) 10–2 V1mA:27V V1mA:22V 10–3 V1mA:18V 10–4 100 10 1 10–5 1050pF 10–6 10–7 0 10 20 Voltage(V) 30 0.01 1 40 TRANSMISSION CHARACTERISTICS 10 100 Frequency(MHz) 1000 10000 CAPACITANCE vs. FREQUENCY CHARACTERISTICS 10 10000 1050pF 0 3.3pF 6.8pF 30pF –20 15pF 160pF 1050pF 650pF –30 650pF 400pF 1000 Capacitance(pF) –10 Insertion loss(dB) 160pF 400pF 650pF 0.1 400pF 160pF 100 30pF 15pF 6.8pF –40 10 3.3pF –50 –60 1 10 100 Frequency(MHz) 1000 10000 1 1 10 100 Frequency(MHz) 1000 10000 • All specifications are subject to change without notice. 001-07 / 20110926 / e9c11_avr.fm (7/10) ELECTROSTATIC DISCHARGE TESTS TEST CONDITIONS 150pF, 330Ω contact discharge Charged voltage /8kV, 0.1s interval MEASURING CIRCUIT 10MΩ 330Ω High voltage DC power supply Discharge gun Test sample 150pF ESD simulator ESD simulator AVR-M1005 TYPE 20 20 10 10 ∆V1mA/V1mA(%) ∆V1mA/V1mA(%) AVR-M0603 TYPE 0 –10 –20 –30 –40 –50 –60 0.1 –20 –30 –40 –50 1 10 Number of discharge(Times) –60 0.1 100 AVR-M1608 TYPE 20 8 10 7 0 –10 –20 –30 –40 –50 –60 0.1 1 10 Number of discharge(Times) 1 10 Number of discharge(Times) 100 AVRL101A3R3F Capacitance(pF) [1MHz] ∆V1mA/V1mA(%) 0 –10 100 6 5 4 3 2 1 0 0.1 1 10 Number of discharge(Times) 100 • All specifications are subject to change without notice. 001-07 / 20110926 / e9c11_avr.fm (8/10) ELECTROSTATIC ABSORPTION CHARACTERISTICS DISCHARGE CURRENT WAVEFORM WAVEFORM PARAMETERS [IEC61000-4-2] 8 Discharge current(A) 6 ESD Charge voltage (kV) 2 4 6 8 Test level 150pF, 330Ω, Contact discharge, Test level 1 7 1 2 3 4 5 4 3 Rise time (ns) 0.7 to 1.0 0.7 to 1.0 0.7 to 1.0 0.7 to 1.0 2 1 MEASURING CIRCUIT 0 –1 –50 0 50 100 150 Time(ns) 200 250 10MΩ 300 High voltage DC power supply DISCHARGE VOLTAGE WAVEFORM 330Ω 150pF ESD simulator 350 Open waveform 300 Discharge gun AVR-M1005C120MTAAB / V1mA:12V 250 Voltage(V) First peak current of discharge (A) 7.5 15 22.5 30 200 Test sample AVR-M1005C080MTAAB / V1mA:8V 150 60dB attenuator Zener diode /Vz:6.2V ESD simulator 100 50 0 –50 –50 0 50 100 150 Time(ns) 200 250 50Ω Oscilloscope I/O impedance: 50Ω Frequency range: DC to 18GHz 300 ESD ABSORPTION CHARACTERISTICS COMPARISON OF VARIOUS ELEMENTS Clamping voltage (V) 350 300 250 269V down 258V down 271V down 200 150 100 101V down 50 0 Open waveform 93V down 96V down AVR-M1005C080MTAAB AVR-M1005C120MTAAB Zener diode/Vz:6.2V Peak 316 45 58 47 Average 117 16 24 21 (voltage) Peak voltage:Peak voltage of standing up part Average voltage : Average voltage of 30 to 100ns Peak voltage ESD (Electro Static Discharge) absorption characteristics of V1mA-8V is superior to Vz-6.2V Zener diode. Average voltage 30 100 (ns) • All specifications are subject to change without notice. 001-07 / 20110926 / e9c11_avr.fm (9/10) MERITS OF REPLACEMENT FROM ZENER DIODE (1) Reduction in the number of parts APPLICATION EXAMPLES CELLULAR PHONE To LCD driver (2) Reduction in mounting cost COMPARISON OF FOOTPRINT Zener diode Chip varistor LCD panel 0.5mm 0.8mm Microphone/Receiver 2.3mm 1.2mm Backlight LED Save a mount area 65% down Data terminal : Chip varistor Key pad/Switch EXAMPLE OF REPLACEMENT AT AUDIO TERMINAL AUDIO/VIDEO Audio connector Audio/out Audio AMP Monitor OUT Video1 in Video2 in Video3 in Video5 in Digi Video Audio connector Audio/out Audio AMP Video Video Video L L/MONO L/MONO L/MONO L/MONO Audio Audio Audio Audio Audio R : Chip varistor : Chip varistor Insulation resistance of tested circuit(Ω) (3) Improved electrostatic absorption capability COMPARE DATA OF CHIP VARISTOR AND ZENER DIODE ABOUT IC PROTECTION 10–7 AVR-M1608C120MT6AB 10–6 10–5 With Zener Diode 10–4 10–3 0 2 4 6 8 10 ESD voltage(kV) 12 14 CMOS: D74HC04C ESD generator : Noise Laboratory Co.,Ltd., ESS -630A 200pF-0Ω method model equipment Contact type discharge ESD applied point: Vcc-ground • All specifications are subject to change without notice. 001-07 / 20110926 / e9c11_avr.fm (10/10) APPLICATION EXAMPLES USB 2.0 VDD USB cable USB IC D– D+ USB connector F.G. : Chip varistor MEASURING CIRCUIT Sample IC USB2.0 board on PC Test board Test set : Chip varistor WITHOUT VARISTOR WITH VARISTOR AVRL101A3R3FT(3.3pF) AVRL101A6R8GT(6.8pF) • All specifications are subject to change without notice. 001-07 / 20110926 / e9c11_avr.fm Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: TDK: AVR-M1608C270KT6AB AVR-M1608C270KT2AB AVR-M1608C080MTAAB AVR-M1005C120MTAAB AVRM1608C120MT6AB AVR-M1608C120MT2AB AVR-M1608C270MTAAB AVR-M1608C270MTABB AVRM2012C120MT6AB AVR-M1005C270MTAAB AVR-M1005C270MTABB AVR-M2012C390KT6AB AVRL101A1R1NTA AVRL101A1R1NTB AVR-M1005C080MTACB AVR-M1005C080MTAAB AVR-M1005C080MTABB AVRL161A1R1NTA AVRL161A1R1NTB AVR-M2012C220KT6AB AVR-M1608C180MT6AB AVR-M1608C220KT6AB AVR-M1608C220KT2AB AVRL101A6R8GTA AVRL161A3R3FTA AVRL161A6R8GTA AVR-M0603C120MTAAB