HIGH CURRENT 2LP Low Profile Power Inductors Description RoHS 2002/95/EC • Compact footprint for high density, high current/low voltage applications • Foil technology that adds higher reliability factor over the traditional magnet wire used for higher frequency circuit designs • Frequency Range up to 1MHz • Ferrite core material Applications • Next generation microprocessors • Energy storage applications • DC-DC converters • Computers Environmental Data • Storage temperature range: -40°C to +125°C • Operating ambient temperature range: -40°C to +85°C (range is application specific). • Solder reflow temperature: +260°C max. for 10 seconds max. Part Number Rated Inductance µH .47 .68 1.0 2.2 4.7 6.0 HC2LP-R47-R HC2LP-R68-R HC2LP-1R0-R HC2LP-2R2-R HC2LP-4R7-R HC2LP-6R0-R OCL (1) µH ± 20% Packaging • Supplied in tape and reel packaging, 44mm width, 130 parts per 13" reel Irms (2) Amperes (Typ.) 52.9 52.9 33.0 24.3 17.0 17.0 .52 .63 1.15 2.00 4.55 6.00 1) Open Circuit Inductance Test Parameters: 300kHz, 0.250 Vrms, 0.0 Adc 2) DC current for an approximate temperature change of 40°C without core loss. Derating is necessary for AC currents. PCB layout, trace thickness and width, air-flow and proximity of other heat generating components will affect the temperature rise. It is recommended that the temperature of the part not exceed 125°C under Isat (3) Amperes (Typ.) 63.75 50.00 42.50 31.90 21.25 16.50 DCR (4) Ohms (Max.) .0006 .0006 .0013 .0023 .0046 .0046 Volts (5) µSec 6.87 6.87 10.31 13.75 20.62 20.62 worst case operating conditions verified in the end application. 3) Peak current for approximately 30% roll-off 4) Values @ 20°C 5) Applied Volt-Time product (V-µS) across the inductor. This value represents the applied V-µS at 300KHz necessary to generate a core loss equal to 10% of the total losses for 40°C temperature rise. Mechanical Diagrams RECOMMENDED PCB PAD LAYOUT TOP VIEW FRONT VIEW 19.2 max 9.5 typ 1 HC2LP-xxx wwllyy R SCHEMATIC 10.00 11.18 max 19.00 2 19.2 max 2.8 typ 5.50 Packaging Information 2 2.3 typ 5.50 1 xxx = Inductance value wwllyy = Date code R = Revision level 4.0 1.5Dia +0.10 -0.00 2.0 1.7 A 20.2 19.3 1 40.4 +/-0.1 44.0 +/-0.3 A 11.3 Dimensions in Millimeters SECTION A-A 19.3 32 User direction of feed Parts packaged on 13" Diameter reel, 130 parts per reel. HIGH CURRENT 2LP Low Profile Power Inductors Core Loss IRMS DERATING WITH CORE LOSS 20 40 50 60 10 0K Hz KH z 20 0 KH z 50 0 30 0 z 80 KH z 70 1M H % of Losses from Irms (maximum) 0 90 92 94 95 96 97 98 99 10 20 30 40 50 60 80 100 200 300 400 500 600 800 1000 % of Applied Volt-µ-Seconds Inductance Characteristics OCL vs. Isat 100 90 80 % of OCL 70 60 50 40 30 20 10 0 0 20 40 60 80 100 120 140 160 180 200 % of ISAT PM-4114 3/07 © Cooper Electronic Technologies 2007 Visit us on the Web at www.cooperbussmann.com 1225 Broken Sound Pkwy. Suite F Boca Raton, FL 33487 Tel: +1-561-998-4100 Toll Free: +1-888-414-2645 Fax: +1-561-241-6640 This bulletin is intended to present product design solutions and technical information that will help the end user with design applications. Cooper Electronic Technologies reserves the right, without notice, to change design or construction of any products and to discontinue or limit distribution of any products. Cooper Electronic Technologies also reserves the right to change or update, without notice, any technical information contained in this bulletin. Once a product has been selected, it should be tested by the user in all possible applications. Life Support Policy: Cooper Electronic Technologies does not authorize the use of any of its products for use in life support devices or systems without the express written approval of an officer of the Company. Life support systems are devices which support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user.