TECHNICAL DATA HIGH-VOLTAGE HIGH-CURRENT DARLINGTON TRANSISTOR ARRAYS The ILN2003A are monolithic high-voltage, high-current Darlington transistor arrays. Each consists of seven n-p-n Darlington pairs that feature high-voltage outputs with commoncathode clamp diodes for switching inductive loads. The collectorcurrent rating of a single Darlington pair is 500 mA. The Darlington pairs may be paralleled for higher current capability. Applications include relay drivers, hammer drivers, lamp drivers, display drivers (LED and gas discharge), line drivers, and logic buffers. The ILN2003A has a 2.7-k series base resistor for each Darlington pair for operation directly with TTL or 5-V CMOS devices. • • • • • 500-mA Rated Collector Current (Single Output) High-Voltage Outputs . . . 50 V Output Clamp Diodes Inputs Compatible With Various Types of Logic Relay Driver Applications LOGIC SYSBOL ILN2003A ORDERING INFORMATION ILN2003AN Plastic ILN2003AD SOIC TA = -20°C to 85° C for all packages LOGIC DIAGRAM SCHEMATICS (each Darlington Pair) All resistor values shown are nominal. ILN2003A: RB = 2.7 kW 1 ILN2003A Absolute maximum ratings at 25°C free-air temperature (unless otherwise noted) Collector-emitter voltage Input voltage, VI (see Note 1) collector current (see Figures 14 and 15) Output clamp current, IOK Total emitter-terminal current Continuous total power dissipation Operating free-air temperature range, TA Storage temperature range, Tstg Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds 50 V 30 V Peak 500 mA 500 mA –2.5 A See Dissipation Rating Table –20°C to 85°C –65°C to 150°C 260°C NOTE 1: All voltage values are with respect to the emitter/substrate terminal E, unless otherwise noted. Electrical characteristics, TA = 25°C (unless otherwise noted) 2 ILN2003A PARAMETER MEASUREMENT INFORMATION 3 ILN2003A Figure 9. Propagation Delay-Time Waveforms NOTES: A. The pulse generator has the following characteristics: PRR = 12.5 kHz, ZO = 50 B. CL includes probe and jig capacitance. C. VIH = 3 V; . Figure 10. Latch-Up Test Circuit and Voltage Waveforms 4 ILN2003A TYPICAL CHARACTERISTICS COLLECTOR-EMITTER SATURATION VOLTAGE vs COLLECTOR CURRENT (ONE DARLINGTON) COLLECTOREMITTER SATURATION VOLTAGE vs TOTAL COLLECTOR CURRENT COLLECTOR CURRENT vs INPUT CURRENT 5 ILN2003A THERMAL INFORMATION D PACKAGE MAXIMUM COLLECTOR CURRENT Vs DUTY CYCLE N PACKAGE MAXIMUM COLLECTOR CURRENT vs DUTY CYCLE Figure 14 Figure 15 APPLICATION INFORMATION 6 ILN2003A 7 ILN2003A N SUFFIX PLASTIC DIP (MS - 001BB) A Dimension, mm 9 16 B 1 8 Symbol MIN MAX A 18.67 19.69 B 6.10 7.11 5.33 C F L C -T- SEATING PLANE N G K D M H J 0.25 (0.010) M T NOTES: 1. Dimensions “A”, “B” do not include mold flash or protrusions. Maximum mold flash or protrusions 0.25 mm (0.010) per side. D 0.36 0.56 F 1.14 1.78 G 2.54 H 7.62 J 0° 10° K 2.92 3.81 L 7.62 8.26 M 0.20 0.36 N 0.38 D SUFFIX SOIC (MS - 012AC) Dimension, mm A 16 9 H B 1 G P 8 R x 45 C -TK D SEATING PLANE J 0.25 (0.010) M T C M F M Symbol MIN MAX A 9.80 10.00 B 3.80 4.00 C 1.35 1.75 D 0.33 0.51 F 0.40 1.27 G 1.27 H 5.72 J 0° 8° K 0.10 0.25 1. Dimensions A and B do not include mold flash or protrusion. M 0.19 0.25 2. Maximum mold flash or protrusion 0.15 mm (0.006) per side for A; for B ‑ 0.25 mm (0.010) per side. P 5.80 6.20 R 0.25 0.50 NOTES: 8