POWER DP40 40 Watts Data Sheet Total Power: 40 Watts Input Voltage: 90 - 264 Vac 127 - 300 Vdc # of Outputs: Single SPECIAL FEATURES Medical and ITE safeties Universal AC input Fully regulated output Overload and short circuit protection Constant voltage High efficiency High MTBF IEC320 AC input receptacle 3 pin (type C14) Class I 2 pin (type C8) Class II Built in EMI filter (CISPR 22 Class B) LED power good indicator Input power <49 watts Complies with EN61000-3-2 Meets Energy Star Efficiency Level V CE Mark EMC, LVD & ErP 2011 Less than 300 mW No-Load power consumption SAFETY UL cUL TUV CE CB CCC 60950-1, 60601-1 60950-1, 60601-1 60950-1, 60601-1 EMC, LVD & ErP 2011 Certificate and report China Approval Electrical Specifications Input Input range 90 - 264 Vac (wide range) 127 - 300 Vdc Frequency 47 - 63 Hz Inrush current < 50 A @ 230 Vac, cold start @ 25 °C Input current < 0.5 A rms @ 115 Vac; < 0.25 A @ 230 Vac Efficiency 84% @ full load typical, @115 Vac EMI/RFI FCC Part 15, Subpart B Class B & EN55022 (CISPR 22) Class B Safety ground leakage current 300 μA @ 50/60 Hz, 264 Vac input for 3 pin model 100 μA @ 50/60 Hz, 264 Vac input for 2 pin model Output Maximum power (Po) 40 W Hold-up time 10 ms. typical at full load @ 115 Vac Overvoltage protection 20% - 45% above nominal output maximum Latching type, recycle AC to reset. Overload protection Output short circuit protection auto recover Overload protected @ 110 - 160% above peak rating Cable/connector 1.2 m DC cable with 2.5 mm I.D, 5.5 mm O.D center plug DC plug center +v DC plug outer -v Environmental Specifications Operating temperature 0 ° to +40 °C ambient. Derate each output as 2.5% per degree from 40 °C to 60 °C. -20 °C start up Storage temperature -40 °C to +85 °C Electromagnetic susceptibility Designed to meet EN61000-4, -2, -3, -4, -5, -6, -8, -11, Level 3 Humidity Operating; non-condensing 10% to 90% RH Vibration Three orthogonal axes, 3 sweeps per axe at 1 oct/min. 2G peak 8 Hz to 500 Hz, operational MTBF demonstrated > 550,000 hours at full load and 25 °C ambient conditions DP40 Data Sheet Ordering Information Model Number Output Voltage Maximum Load Peak Load1 Regulation2 Ripple P/P (PARD)3 DP4009N2M DP4009N3M 9V 4.44 A 5.4 A ± 8% 90 mV 9V 4.44 A 5.4 A ± 8% 90 mV DP4012N2M 12 V 3.33 A 4.4 A ± 5% 120 mV DP4012N3M 12 V 3.33 A 4.4 A ± 5% 120 mV DP4015N2M 15 V 2.67 A 3.5 A ± 5% 150 mV DP4015N3M 15 V 2.67 A 3.5 A ± 5% 150 mV DP4018N2M 18 V 2.22 A 3.0 A ± 5% 150 mV DP4018N3M 18 V 2.22 A 3.0 A ± 5% 150 mV DP4024N2M 24 V 1.67 A 2.2 A ± 5% 240 mV DP4024N3M 24 V 1.67 A 2.2 A ± 5% 240 mV DP4048N2M 48 V 0.84 A 1.2 A ± 5% 480 mV DP4048N3M 48 V 0.84 A 1.2 A ± 5% 480 mV 1. Peak current lasting < 15 seconds with a maximum 10% duty cycle. 2. At 25 ºC including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3. Peak-to-peak with 20 MHz bandwidth and 10 μF (tantalum capacitor) in parallel with a 0.1 μF capacitor at rated line voltage and load ranges. 2.4" (61.0) Mechanical Drawing 4.88" (124.0) Notes: 1. Specifications subject to change without notice. 2. All dimensions in inches (mm), tolerance is ± 0.02” (± 0.5 mm) 3. Warranty: 2 year 4. Weight: 0.55 lb./.25 kg 5. AC input power cord sold separately. 6. Specifications are for convection rating at factory settings at 115 Vac input, 25 °C unless otherwise stated 2.4" (61.0) 1.55" (39.5) 48" (1219 ± 20) 4.88" (124.0) 1.55" (39.5) 48" (1219 ± 20) WORLDWIDE OFFICES Americas Europe (UK) Asia (HK) 2900 S.Diablo Way Tempe, AZ 85282 USA +1 888 412 7832 Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom +44 (0) 1384 842 211 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong +852 2176 3333 While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. © 2015 Artesyn Embedded Technologies, Inc. www.artesyn.com For more information: www.artesyn.com/power For support: [email protected] DP40-DS 09Jul2015