ES1A THRU ES1D SURFACE MOUNT ULTRAFAST EFFICIENT PLASTIC RECTIFIER Reverse Voltage - 50 to 200 Volts Forward Current - 1.0 Ampere FEATURES DO-214AC 0.065 (1.65) 0.110 (2.79) 0.100 (2.54) 0.049 (1.25) 0.177 (4.50) 0.157 (3.99) 0.012 (0.305) 0.006 (0.152) 0.090 (2.29) ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ For surface mount applications ♦ Low profile package ♦ Ideally suited for use in very high frequency switching power supplies, inverters and as a free wheeling diodes ♦ Ultrafast recovery times for high efficiency ♦ Low forward voltage ♦ Low leakage current ♦ Glass passivated chip junction ♦ High temperature soldering guaranteed: 250°C/10 seconds on terminals 0.078 (1.98) MECHANICAL DATA 0.060 (1.52) 0.008 (0.203) MAX. 0.030 (0.76) 0.208 (5.28) 0.194 (4.93) Dimensions in inches and (millimeters) Case: JEDEC DO-214AC molded plastic body over passivated chip Terminals: Solder plated, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Weight: 0.002 ounces, 0.064 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS Device marking code ES1A ES1B ES1C ES1D EA EB EC ED UNITS Maximum repetitive peak reverse voltage VRRM 50 100 150 200 Volts Maximum RMS voltage VRMS 35 70 105 140 Volts Maximum DC blocking voltage VDC 50 100 150 200 Volts Maximum average forward rectified current at TL=120°C I(AV) 1.0 Amp Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) IFSM 30.0 Amps VF 0.865 0.920 Volts IR 5.0 100 µA Maximum instantaneous forward voltage at 0.6A at 1.0A Maximum DC reverse current at rated DC blocking voltage TA=25°C TA=100°C Maximum reverse recovery time (NOTE 1) Maximum reverse recovery time (NOTE 2) Maximum stored charge (NOTE 2) Typical junction capacitance (NOTE 3) Maximum thermal resistance (NOTE 4) Operating and storage temperature range trr 15.0 ns TA=25°C TA=100°C trr 25.0 35.0 ns TA=25°C TA=100°C Qrr 10.0 25.0 nC CJ 7.0 pF RΘJA RΘJL 85.0 35.0 °C/W TJ, TSTG -55 to +150 °C NOTES: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A (2) trr and Qrr measured at: IF=0.6A, VR=30V, di/dt=50A/µs, Irr =10% IRM for measurement of trr (3) Measured at 1.0 MHZ and applied reverse voltage of 4.0 volts (4) P.C.B. mounted on 0.2 x 0.2” (5.0 x 5.0mm) copper pad area 4/98 RATINGS AND CHARACTERISTIC CURVES ES1A THRU ES1D FIG. 1 - MAXIMUM FORWARD CURRENT DERATING CURVE FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 30 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES 1.2 1.0 RESISTIVE OR INDUCTIVE LOAD 0.2 x 0.2” (5.0 x 5.0mm) COPPER PAD AREAS 0.8 0.6 0.4 0.2 0 80 90 100 110 120 130 140 150 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) at TL=120°C 25 20 15 10 5.0 0 1 10 LEAD TEMPERATURE, °C 100 NUMBER OF CYCLES AT 60 HZ FIG. 4 - TYPICAL REVERSE LEAKAGE CHARACTERISTICS 1,000 FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 10 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 1 0.1 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 50 100 TJ=125°C 10 TJ=85°C 1 TJ=25°C 0.1 1.8 0.01 0 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 12 10 8.0 6.0 4.0 2.0 0 0.1 1 10 REVERSE VOLTAGE, VOLTS 100 60 80 100 FIG. 5 - TYPICAL THERMAL IMPEDANCE TRANSIENT THERMAL IMPEDANCE, °C/W JUNCTION CAPACITANCE, pF TJ=25°C f=1.0 MHZ Vsig=50mVp-p 40 PERCENT OF RATED PEAK REVERSE VOLTAGE, % FIG. 5 - TYPICAL JUNCTION CAPACITANCE 14 20 100 MOUNTED on 0.2 x 0.2”(5 x 7mm) COPPER PAD AREAS 10 1 0.1 1 10 t, PULSE DURATION, SEC 100