LINER LT1769CGN Constant-current/ constant-voltage 2a battery charger with input current limiting Datasheet

LT1769
Constant-Current/
Constant-Voltage 2A Battery
Charger with Input Current Limiting
DESCRIPTIO
U
FEATURES
■
■
■
■
■
■
■
■
■
■
■
■
The LT®1769 current mode PWM battery charger is a
simple, efficient solution to fast charge modern rechargeable batteries including lithium-ion (Li-Ion), nickel-metalhydride (NiMH) and nickel-cadmium (NiCd) that require
constant-current and/or constant-voltage charging. The
internal switch is capable of delivering 2A** DC current
(3A peak current). Charge current can be programmed by
resistors or a DAC to within 5%. With 0.5% reference voltage
accuracy, the LT1769 meets the critical constant-voltage
charging requirement for Li-Ion cells.
Simple Solution to Charge NiCd, NiMH and Lithium
Rechargeable Batteries—Charging Current
Programmed by Resistors or DAC
Adapter Current Limit Allows Maximum Possible
Charging Current During System Use*
Precision 0.5% Accuracy for Voltage Mode Charging
High Efficiency Current Mode PWM with 3A Internal
Switch
5% Charge Current Accuracy
Adjustable Undervoltage Lockout
Automatic Shutdown When AC Adapter is Removed
Low Reverse Battery Drain Current: 3µA
Current Sensing Can Be at Either Terminal of the Battery
Charging Current Soft Start
Shutdown Control
Available in 28-Lead Narrow SSOP Package
A third control loop is provided to regulate the current
drawn from the input AC adapter. This allows simultaneous operation of the equipment and battery charging
without overloading the adapter. Charge current is reduced
to keep the adapter current below specified levels.
The LT1769 can charge batteries ranging from 1V to 20V.
Ground sensing of current is not required and the battery’s
negative terminal can be tied directly to ground. A saturating switch running at 200kHz gives high charging efficiency and small inductor size. A blocking diode is not
required between the chip and the battery because the
chip goes into sleep mode and drains only 3µA when the
wall adapter is unplugged.
U
APPLICATIO S
■
■
Chargers for NiCd, NiMH, Lead-Acid, Lithium
Rechargeable Batteries
Switching Regulators with Precision Current Limit
, LTC and LT are registered trademarks of Linear Technology Corporation.
*US patent number 5,723,970
**See LT1510 for 1.5A charger; see LT1511 for 3A charger
U
TYPICAL APPLICATIO
C2
0.47µF
††
D1
SS24
GND
CLP
SW
CLN
VCC
C1
1µF
UV
COMP1
2nF
10k
VC
SPIN
RS3
200Ω
1%
BAT
VIN (ADAPTER INPUT)
11V TO 28V
TO MAIN
SYSTEM LOAD
R5†
UNDERVOLTAGE
LOCKOUT
R6
5k
PROG
OVP SENSE
NOTE: COMPLETE LITHIUM-ION CHARGER,
NO TERMINATION REQUIRED. RS4, R7
AND C1 ARE OPTIONAL FOR IIN LIMITING
*TOKIN OR UNITED CHEMI-CON/MARCON
CERAMIC SURFACE MOUNT
**22µH SUMIDA CDRH125
†
SEE APPLICATIONS INFORMATION FOR
INPUT CURRENT LIMIT AND UNDERVOLTAGE LOCKOUT
††
GENERAL SEMICONDUCTOR. FOR TJ LESS THEN 100°C
MBRS130LT3 CAN BE USED
RS4†
ADAPTER
CURRENT SENSE
CIN*
15µF
BOOST
LT1769
L1**
22µH
D2
1N4148
D3††
SS24
R7†
500Ω
300Ω
0.33µF
CPROG
1µF
RPROG
4.93k
1%
RS2
200Ω
1%
RS1
0.05Ω
BATTERY CURRENT
SENSE
R3
+
390k
0.25%
BATTERY
VOLTAGE SENSE
VBAT
COUT
22µF
TANT
8.4V
Li-Ion
1511 • F01
R4
162k
0.25%
Figure 1. 2A Lithium-Ion Battery Charger
1
LT1769
U
W
U
U
W W
W
ABSOLUTE MAXIMUM RATINGS
PACKAGE/ORDER INFORMATION
(Note 1)
Supply Voltage
(VCC, CLP and CLN Pin Voltage) ......................... 30V
BOOST Pin Voltage with Respect to VCC ................. 25V
IBAT (Average)........................................................... 2A
Operating Junction Temperature Range
Commercial ........................................... 0°C to 125°C
Industrial ......................................... – 40°C to 125°C
Operating Ambient Temperature
Commercial ............................................ 0°C to 70°C
Industrial ........................................... – 40°C to 85°C
Storage Temperature Range ................. – 65°C to 150°C
Lead Temperature (Soldering, 10 sec).................. 300°C
ORDER PART
NUMBER
TOP VIEW
GND**
1
28 GND**
GND**
2
27 GND**
GND**
3
26 GND**
SW
4
25 VCC1*
BOOST
5
24 VCC2*
UV
6
23 VCC3*
GND**
7
22 GND**
GND**
8
21 PROG
OVP
9
20 VC
CLP 10
19 UVOUT
CLN 11
18 COMP2
COMP1 12
17 BAT
SENSE 13
16 SPIN
GND** 14
15 GND**
LT1769CGN
LT1769IGN
*ALL VCC PINS SHOULD
BE CONNECTED
TOGETHER CLOSE TO
THE PINS
** ALL GND PINS ARE
FUSED TO INTERNAL DIE
ATTACH PADDLE FOR
HEAT SINKING. CONNECT
THESE PINS TO
EXPANDED PC LANDS
FOR PROPER HEAT
SINKING. 35°C/W
THERMAL RESISTANCE
ASSUMES AN INTERNAL
GROUND PLANE
DOUBLING AS A HEAT
SPREADER
GN PACKAGE
28-LEAD PLASTIC SSOP
TJMAX = 125°C, θJA = 35°C/ W**
Consult factory for Military grade parts.
ELECTRICAL CHARACTERISTICS
The ● denotes specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VCC = 16V, VBAT = 8V, RS2 = RS3 = 200Ω (see Block Diagram),
VCLN = VCC. No load on any outputs unless otherwise noted.
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
4.5
4.6
6.8
7.0
mA
mA
100
10
107
12
12
mV
mV
mV
110
14
13
mV
mV
mV
Overall
Supply Current
VPROG = 2.7V, VCC ≤ 20V
VPROG = 2.7V, 20V < VCC ≤ 25V
Sense Amplifier CA1 Gain and Input Offset Voltage
(With RS2 = 200Ω, RS3 = 200Ω)
(Measured across RS1)(Note 2)
8V ≤ VCC ≤ 25V , 0V ≤ VBAT ≤ 20V
RPROG = 4.93k
RPROG = 49.3k
TA < 0°C
VCC = 28V, VBAT = 20V
RPROG = 4.93k
RPROG = 49.3k
TA < 0°C
●
●
●
●
93
8
7
●
●
90
6
7
6
VCC Undervoltage Lockout (Switch OFF) Threshold
Measured at UV Pin
●
7
8
V
UV Pin Input Current
0.2V ≤ VUV ≤ 8V
●
0.1
5
µA
UV Output Voltage at UVOUT Pin
In Undervoltage State, IUVOUT = 70µA
●
0.1
0.5
V
UV Output Leakage Current at UVOUT Pin
8V ≤ VUV, VUVOUT = 5V
●
0.1
3
µA
Reverse Current from Battery (When VCC Is
Not Connected, VSW Is Floating)
VBAT ≤ 20V, VUV ≤ 0.4V
3
15
µA
2
LT1769
ELECTRICAL CHARACTERISTICS
The ● denotes specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VCC = 16V, VBAT = 8V, RS2 = RS3 = 200Ω (see Block Diagram),
VCLN = VCC. No load on any outputs unless otherwise noted.
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
0.1
0.25
6
8
10
20
9
12
µA
µA
mA
mA
0.15
0.25
Ω
25
35
mA/A
2
4
100
200
µA
µA
20
µA
Overall
Boost Pin Current
VCC = 20V, VBOOST = 0V
VCC = 28V, VBOOST = 0V
2V ≤ VBOOST – VCC < 8V (Switch ON)
8V ≤ VBOOST – VCC ≤ 25V (Switch ON)
Switch
Switch ON Resistance
8V ≤ VCC ≤ VMAX, ISW = 2A,
VBOOST – VSW ≥ 2V
∆IBOOST/∆ISW During Switch ON
VBOOST = 24V, ISW ≤ 2A
Switch OFF Leakage Current
VSW = 0V, VCC ≤ 20V
20V < VCC ≤ 28V
●
●
●
Minimum IPROG for Switch ON
●
2
4
Minimum IPROG for Switch OFF
●
1
2.4
Maximum VBAT for Switch ON
●
mA
VCC – 2
V
– 125
µA
Current Sense Amplifier CA1 Inputs (Sense, BAT)
Input Bias Current
●
Input Common Mode Low
●
Input Common Mode High
●
– 50
– 0.25
SPIN Input Current
V
VCC – 2
V
– 100
– 200
µA
2.465
2.477
V
2.489
2.489
V
V
Reference
Reference Voltage (Note 3)
Reference Voltage
RPROG = 4.93k, Measured at OVP with
VA Supplying IPROG and Switch OFF
All Conditions of VCC, TA ≥ 0°C
TA < 0°C (Note 4)
2.448
●
●
2.441
2.43
Oscillator
Switching Frequency
Switching Frequency
All Conditions of VCC, TA ≥ 0°C
TA < 0°C
180
200
220
kHz
●
●
170
160
200
230
230
kHz
kHz
90
85
93
●
150
250
Maximum Duty Cycle
%
%
Current Amplifier CA2
Transconductance
VC = 1V, IVC = ±1µA
Maximum VC for Switch OFF
IVC Current (Out of Pin)
●
VC ≥ 0.6V
VC < 0.45V
550
µmho
0.6
V
100
3
µA
mA
3
LT1769
ELECTRICAL CHARACTERISTICS
The ● denotes specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VCC = 16V, VBAT = 8V. No load on any outputs unless otherwise noted.
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Transconductance (Note 3)
Output Current from 50µA to 500µA
0.25
0.6
1.3
mho
Output Source Current
VOVP = VREF + 10mV, VPROG = VREF + 10mV
1.1
OVP Input Bias Current
VA Output Current at 0.5mA
VA Output Current at 0.5mA, TA > 90°C
Voltage Amplifier VA
●
●
mA
±3
±10
25
nA
nA
–15
Current Limit Amplifier CL1, 8V ≤ Input Common Mode
Turn-On Threshold
0.5mA Output Current
93
100
107
mV
Transconductance
Output Current from 50µA to 500µA
0.5
1
2
mho
CLP Input Current
0.5mA Output Current, VUV ≥ 0.4V
0.3
1
µA
CLN Input Current
0.5mA Output Current VUV ≥ 0.4V
0.8
2
mA
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 2: Tested with Test Circuit 1.
Note 3: Tested with Test Circuit 2.
Note 4: A linear interpolation can be used for reference voltage
specification between 0°C and – 40°C.
U W
TYPICAL PERFORMANCE CHARACTERISTICS
100
98
ICC vs VCC
ICC vs Duty Cycle
Efficiency of Figure 1 Circuit
7.0
8
VIN = 16.5
VBAT = 8.4V
7
6
94
TJ = 25°C
CHARGER EFFICIENCY
90
88
5
TJ = 0°C
TJ = 125°C
4
TJ = 25°C
3
86
INCLUDES LOSS
IN DIODE D3
84
ICC (mA)
92
ICC (mA)
EFFICIENCY (%)
TJ = 0°C
6.5
96
2
6.0
TJ = 125°C
5.5
5.0
1
82
4.5
0
80
0.2
0.6
1.0
1.4
IBAT (A)
1.8
2.2
1769 G01
4
MAXIMUM DUTY CYCLE
VCC = 16V
0
10
20
30 40 50 60
DUTY CYCLE (%)
70
80
1769 G02
0
5
10
15
VCC (V)
20
25
30
1769 G03
LT1769
U W
TYPICAL PERFORMANCE CHARACTERISTICS
IVA vs ∆VOVP (Voltage Amplifier)
VREF Line Regulation
0.003
4
0.002
3
ALL TEMPERATURES
∆VOVP (mV)
∆VREF (V)
0.001
0
2
TJ = 125°C
–0.001
1
–0.002
–0.003
TJ = 25°C
0
10
5
15
VCC (V)
20
25
0
30
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
IVA (mA)
1769 G04
1769 G05
Maximum Duty Cycle
VC Pin Characteristics
98
–1.20
–1.08
97
–0.96
–0.84
–0.72
95
IVC (mA)
DUTY CYCLE (%)
96
94
–0.60
–0.48
93
–0.36
92
–0.24
–0.12
91
0
90
0
20
60
40
80 100 120
JUNCTION TEMPERATURE (°C)
0.12
140
0
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
VC (V)
1769 G06
1769 G07
Reference Voltage
vs Temperature
PROG Pin Characteristics
2.470
6
REFERENCE VOLTAGE (V)
2.468
IPROG (mA)
TJ = 125°C
TJ = 25°C
0
2.466
2.464
2.462
2.460
2.458
–6
0
1
2
3
VPROG (V)
4
5
1769 G08
0
25
125
50
75
100
JUNCTION TEMPERATURE
150
1769 G09
5
LT1769
U
U
U
PIN FUNCTIONS
GND (Pins 1 to 3, 7, 8, 14, 15, 22, 26 to 28): Ground Pins.
Must be connected to expanded PC lands for proper heat
sinking. See Applications Information section for details.
SW (Pin 4): Switch Output. The Schottky catch diode must
be placed with very short lead length in close proximity to
SW pin and GND.
BOOST (Pin 5): This pin is used to bootstrap and drive the
switch power NPN transistor to a low on-voltage for low
power dissipation. In Figure 1, VBOOST = VCC + VBAT when
switch is on. For lowest IC power dissipation, connect
boost diode D1 to a 3V to 6V at 30mA voltage source (see
Figure 10).
UV (Pin 6): Undervoltage Lockout Input. The rising threshold is at 6.7V with a hysteresis of 0.5V. Switching stops in
undervoltage lockout. When the input supply (normally
the wall adapter output) to the IC is removed, the UV pin
must be pulled down to below 0.7V (a 5k resistor from
adapter output to GND is required) otherwise the reverse
battery current drained by the IC will be approximately
200µA instead of 3µA. Do not leave the UV pin floating.
When connected to VIN with no resistor divider, the builtin 6.7V undervoltage lockout will be effective.
OVP (Pin 9): This is the input to amplifier VA with a
threshold of 2.465V. Typical bias current is about 3nA out
of this pin. For charging lithium-ion batteries, VA monitors
the battery voltage and reduces charging when battery
voltage reaches the preset value. If it is not used, the OVP
pin should be grounded.
CLP (Pin 10): This is the positive input to the input current
limit amplifier CL1. The threshold is set at 100mV. When
used to limit supply current, a filter is needed to filter out
the 200kHz switching noise.
CLN (Pin 11): This is the negative input to the input current
limit amplifier CL1.
COMP1 (Pin 12): This is the compensation node for the
input current limit amplifier CL1. At input adapter current
limit, this node rises to 1V. By forcing COMP1 low with an
external transistor, amplifier CL1 will be defeated (no
adapter current limit). COMP1 can source 200µA. If this
function is not used, the resistor and capacitor on COMP1
pin, shown on the Figure 1 circuit, are not needed.
6
SENSE (Pin 13): Current Amplifier CA1 Input. Sensing can
be at either terminal of the battery.
SPIN (Pin 16): This pin is for the current amplifier CA1
bias. It must be connected to RS1 as shown in the 2A
Lithium Battery Charger (Figure 1).
BAT (Pin 17): Current Amplifier CA1 Input.
COMP2 (Pin 18): This is also a compensation node for
amplifier CL1. Voltage on this pin rises to 2.8V at input
adapter current limit and/or at constant-voltage charging.
UVOUT (Pin 19): This is an open-collector output for
undervoltage lockout status. It stays low in undervoltage
state. With an external pull-up resistor, it goes high at valid
VCC. Note that the base drive of the open-collector NPN
comes from CLN pin. UVOUT stays low only when CLN is
higher than 2V. Pull-up current should be kept under
100µA.
VC (Pin 20): This is the inner loop control signal for the
current mode PWM. Switching starts at 0.7V. In normal
operation, a higher VC corresponds to higher charge
current. A capacitor of at least 0.33µF to GND filters out
noise and controls the rate of soft start. To stop switching,
pull this pin low. Typical output current is 30µA.
PROG (Pin 21): This pin is for programming the charge
current and for system loop compensation. During normal
operation, VPROG stays close to 2.465V. If it is shorted to
GND switching will stop. When a microprocessor controlled DAC is used to program charge current, it must be
capable of sinking current at a compliance up to 2.465V.
VCC1, VCC2, VCC3 (Pins 23 to 25): Input Supply. For good
bypass, a low ESR capacitor of 15µF or higher is required,
with the lead length kept to a minimum. VCC should be
between 8V and 28V and at least 3V higher than VBAT.
Undervoltage lockout starts and switching stops when
VCC goes below 7V typical. Note that there is an internal
parasitic diode from SW pin to VCC pin. Do not force VCC
below SW by more than 0.7V with battery present. All three
VCC pins should be shorted together close to the pins.
LT1769
W
BLOCK DIAGRAM
–
UV
UVOUT
+
+
7V
200kHz
OSCILLATOR
+
SHUTDOWN
0.7V
+
VCC
–
VSW
S
BOOST
–
VCC
R
R
+
+
SLOPE COMPENSATION
SW
1.5V
VCC
SPIN
VBAT
–
PWM
C1
–
+
B1
+
GND
QSW
R
R2
+
SENSE
RS3
–
BAT
RS2
CA1
IPROG
R1
1k
R3
0VP
–
VA
CA2
+
75k
RS1
BAT
+
VC
IBAT
gm = 0.64
VREF
Ω
–
VREF
2.465V
100mV
+
CLP
+
CL1
–
CLN
COMP1
COMP2
PROG
CPROG
IPROG
RPROG
)(R )
(I
IBAT = PROG S2
RS1
RS2
= 2.465V
RPROG RS1
1769 BD
( )( )
(RS3 = RS2)
7
LT1769
TEST CIRCUITS
Test Circuit 1
SPIN
LT1769
CA1
CA2
1k
+
0.047µF
+
–
VC
60k
–
SENSE
RS3
200Ω
BAT
RS2
200Ω
RS1
100Ω
+
VBAT
VREF
PROG
1µF
RPROG
300Ω
+
LT1006
1k
+
1769 TC01
–
≈ 0.65V
20k
Test Circuit 2
LT1769
OVP
+
VA
–
VREF
PROG
10k
IPROG
10k
0.47µF
RPROG
–
+
+
LT1013
2.465V
1769 TC02
U
OPERATION
The LT1769 is a current mode PWM step-down (buck)
switcher. The battery DC charge current is programmed
by a resistor RPROG (or a DAC output current) at the PROG
pin (see Block Diagram). Amplifier CA1 converts the
charge current through RS1 to a much lower current IPROG
fed into the PROG pin. Amplifier CA2 compares the output
of CA1 with the programmed current and drives the PWM
control loop to force them to be equal. High DC accuracy
is achieved with averaging capacitor CPROG. Note that
IPROG has both AC and DC components. IPROG goes
through R1 and generates a ramp signal that is fed to the
PWM control comparator C1 through buffer B1 and level
8
shift resistors R2 and R3, forming the current mode inner
loop. The BOOST pin drives the switch NPN QSW into
saturation and reduces power loss. For batteries like
lithium-ion that require both constant-current and constant-voltage charging, the 0.5%, 2.465V reference and
the amplifier VA reduce the charge current when battery
voltage reaches the preset level. For NiMH and NiCd, VA
can be used for overvoltage protection. When the input
voltage is removed, the VCC pin drops to 0.7V below the
battery voltage, forcing the charger into a low battery drain
(3µA typical) sleep mode. To shut down the charger,
simply pull the VC pin low with a transistor.
LT1769
U
U
W
U
APPLICATIONS INFORMATION
Input and Output Capacitors
In the 2A Lithium-Ion Battery Charger (Figure 1), the input
capacitor (CIN) is assumed to absorb all input switching
ripple current in the converter, so it must have adequate
ripple current rating. Worst-case RMS ripple current will
be equal to one half of the output charge current. Actual
capacitance value is not critical. Solid tantalum capacitors
such as the AVX TPS and Sprague 593D series have high
ripple current rating in a relatively small surface mount
package, but caution must be used when tantalum capacitors are used for input bypass. High input surge currents
are possible when the adapter is hot-plugged to the
charger and solid tantalum capacitors have a known
failure mechanism when subjected to very high turn-on
surge currents. Selecting a high voltage rating on the
capacitor will minimize problems. Consult with the manufacturer before use. Alternatives include new high capacity
ceramic (5µF to 20µF) from Tokin or United Chemi-Con/
Marcon, et al. Sanyo OS-CON can also be used.
The output capacitor (COUT) is also assumed to absorb
output switching ripple current. The general formula for
capacitor ripple current is:
(
)
V
0.29 (VBAT) 1 – BAT
VCC
IRMS =
(L1)(f)
For example, VCC = 16V, VBAT = 8.4V, L1 = 20µH,
and f = 200kHz, IRMS = 0.3A.
EMI considerations usually make it desirable to minimize
ripple current in the battery leads. Beads or inductors can
be added to increase battery impedance at the 200kHz
switching frequency. Switching ripple current splits between the battery and the output capacitor depending on
the ESR of the output capacitor and the battery impedance. If the ESR of COUT is 0.2Ω and the battery impedance
is raised to 4Ω with a bead or inductor, only 5% of the
ripple current will flow into the battery.
Soft-Start and Undervoltage Lockout
The LT1769 is soft-started by the 0.33µF capacitor on the
VC pin. On start-up, the VC pin voltage will quickly rise to
0.5V, then ramp at a rate set by the internal 45µA pull-up
current and the external capacitor. Charge current starts
ramping up when VC pin voltage reaches 0.7V and full
current is achieved with VC at 1.1V. With a 0.33µF capacitor, the time to reach full charge current is about 10ms and
it is assumed that input voltage to the charger will reach
full value in less than 10ms. The capacitor can be
increased up to 1µF if longer input start-up times are
needed.
In any switching regulator, conventional time-based softstarting can be defeated if the input voltage rises much
slower than the time out period. This happens because the
switching regulators in the battery charger and the computer power supply are typically supplying a fixed amount
of power to the load. If the input voltage comes up slowly
compared to the soft-start time, the regulators will try to
deliver full power to the load when the input voltage is still
well below its final value. If the adapter is current limited,
it cannot deliver full power at reduced output voltages and
the possibility exists for a quasi “latch” state where the
adapter output stays in a current limited state at reduced
output voltage. For instance, if maximum charger plus
computer load power is 25W, a 15V adapter might be
current limited at 2A. If adapter voltage is less than
(25W/2A = 12.5V) when full power is drawn, the adapter
voltage will be pulled down by the constant 25W load until
it reaches a lower stable state where the switching regulators can no longer supply full load. This situation can be
prevented by utilizing undervoltage lockout, set higher
than the minimum adapter voltage where full power can be
achieved.
A fixed undervoltage lockout of 7V is built into the LT1769.
This 7V threshold can be increased by adding a resistive
divider to the UV pin as shown in Figure 2. Internal lockout
is performed by clamping the VC pin low. The VC pin is
released from its clamped state when the UV pin rises
above 7V and is pulled low when the UV pin drops below
6.5V (0.5V hysteresis). At the same time UVOUT goes high
with an external pull-up resistor. This signal can be used
to alert the system that charging is about to start. The
charger will start delivering current about 4ms after VC is
released, as set by the 0.33µF capacitor. A resistor divider
is used to set the desired VCC lockout voltage as shown in
Figure 2. A typical value for R6 is 5k and R5 is found from:
9
LT1769
U
U
W
U
APPLICATIONS INFORMATION
R5 =
ally, batteries will automatically be charged at the maximum
possible rate of which the adapter is capable.
R6(VIN – VUV )
VUV
VUV = Rising lockout threshold on the UV pin
VIN = Charger input voltage that will sustain full load power
Example: With R6 = 5k, VUV = 6.7V and setting VIN at 12V;
R5 = 5k (12V – 6.7V)/6.7V = 4k
The resistor divider should be connected directly to the
adapter output as shown, not to the VCC pin, to prevent
battery drain with no adapter voltage. If the UV pin is not
used, connect it to the adapter output (not VCC) and
connect a resistor no greater than 5k to ground. Floating
this pin will cause reverse battery current to increase from
3µA to 200µA.
If connecting the unused UV pin to the adapter output is
not possible, it can be grounded. Although it would seem
that grounding the pin creates a permanent lockout state,
the UV circuitry is arranged for phase reversal with low
voltages on the UV pin to allow the grounding technique to
work.
100mV
+
+
–
Charge Current Programming
The basic formula for charge current is (see Block
Diagram):
IBAT = IPROG
( )(
RS2
2.465V
=
RS1
RPROG
)( )
RS2
RS1
where RPROG is the total resistance from PROG pin to ground.
CLP
1µF
CL1
This is accomplished by sensing total adapter output
current and adjusting the charge current downward if a
preset adapter current limit is exceeded. True analog
control is used, with closed-loop feedback ensuring that
adapter load current remains below the limit. Amplifier
CL1 in Figure 2 senses the voltage across RS4, connected
between the CLP and CLN pins. When this voltage exceeds
100mV, the amplifier will override the programmed charge
current to limit adapter current to 100mV/RS4. A lowpass
filter formed by 500Ω and 1µF is required to eliminate
switching noise. If the input current limit is not used, both
CLP and CLN pins should be connected to VCC.
CLN
500Ω
RS4*
VCC
AC ADAPTER
OUTPUT
VIN
+
R5
LT1769
UV
*RS4 =
100mV
ADAPTER CURRENT LIMIT
R6
For the sense amplifier CA1 biasing purpose, RS3 should
have the same value as RS2 and SPIN should be connected
directly to the sense resistor (RS1) as shown in the Block
Diagram.
For example, 2A charge current is needed. For low power
dissipation on RS1 and enough signal to drive the amplifier
CA1, let RS1 = 100mV/2A = 0.05Ω. This limits RS1 power
to 0.2W. Let RPROG = 5k, then:
1769 F02
Figure 2. Adapter Input Current Limiting
Adapter Current Limiting
An important feature of the LT1769 is the ability to
automatically adjust charge current to a level which avoids
overloading the wall adapter. This allows the product to
operate at the same time the batteries are being charged
without complex load management algorithms. Addition-
10
)(R )
(I )(R
RS2 = RS3 = BAT PROG S1
2.465V
(2A)(5k)(0.05)
=
= 200Ω
2.465V
Charge current can also be programmed by pulse width
modulating IPROG with a switch Q1 to RPROG at a frequency
higher than a few kHz (Figure 3). Charge current will be
proportional to the duty cycle of the switch with full current
at 100% duty cycle.
LT1769
U
U
W
U
APPLICATIONS INFORMATION
LT1769
PROG
300Ω
RPROG
4.7k
5V
0V
CPROG
1µF
Q1
VN2222
PWM
IBAT = (DC)(2A)
1769 F03
Figure 3. PWM Current Programming
When power is on, there is about 200µA of current flowing
out of the BAT and SENSE pins. If the battery is removed
during charging, and total load including R3 and R4 is less
than 200µA, VBAT could float up to VCC even though the
loop has turned switching off. To keep VBAT regulated to
the battery voltage in this condition, R3 and R4 can be
chosen to draw 0.5mA and Q3 can be added to disconnect
them when power is off (Figure 4). R5 isolates the OVP pin
from any high frequency noise on VIN. An alternative method
is to use a Zener diode with a breakdown voltage two or three
volts higher than battery voltage to clamp the VBAT voltage.
Lithium-Ion Charging
The 2A Lithium-Ion Battery Charger (Figure 1) charges at
a constant 2A until battery voltage reaches a limit set by R3
and R4. The charger will then automatically go into a
constant-voltage mode with current decreasing to near
zero over time as the battery reaches full charge. This is the
normal regimen for lithium-ion charging, with the charger
holding the battery at “float” voltage indefinitely. In this
case no external sensing of full charge is needed.
Battery Voltage Sense Resistors Selection
To minimize battery drain when the charger is off, current
through the R3/R4 divider is set at 15µA. The input current
to the OVP pin is 3nA and the error can be neglected.
With divider current set at 15µA, VBAT = 8.4V, R4 =
2.465/15µA = 162k and,
R3 =
(R4)(VBAT − 2.465) = 162k (8.4 − 2.465)
2.465
2.465
= 390k
Li-Ion batteries typically require float voltage accuracy of
1% to 2%. Accuracy of the LT1769 OVP voltage is ±0.5%
at 25°C and ±1% over full temperature. This leads to the
possibility that very accurate (0.1%) resistors might be
needed for R3 and R4. Actually, the temperature of the
LT1769 will rarely exceed 50°C in float mode because
charging currents have tapered off to a low level, so 0.25%
resistors will normally provide the required level of overall
accuracy.
LT1769
Q3
VN2222
R5
220k
VBAT
+
R3
12k
0.25%
8.4V
VIN
OVP
R4
4.99k
0.25%
1769 F04
Figure 4. Disconnecting Voltage Divider
Some battery manufacturers recommend terminating the
constant-voltage float mode after charge current has
dropped below a specified level (typically around 10% of
the full current) and a further time out period of 30 to 90
minutes has elapsed. This may extend battery life, so
check with the manufacturer for details. The circuit in
Figure 5 will detect when charge current has dropped
below 270mA. This logic signal is used to initiate a timeout
period, after which the LT1769 can be shut down by
pulling the VC pin low with an open collector or drain.
Some external means must be used to detect the need for
additional charging or the charger may be turned on
periodically to complete a short float-voltage cycle.
Current trip level is determined by the battery voltage, R1
through R3 and the sense resistor (RS1). D2 generates
hysteresis in the trip level to avoid multiple comparator
transitions.
11
LT1769
U
U
W
U
APPLICATIONS INFORMATION
IBAT
R1 =
RS3
200Ω
SENSE
RS1
0.05Ω
LT1769
RS2
200Ω
BAT
VBAT
ADAPTER
OUTPUT
BAT
R1* C1
1.6k 0.1µF
3.3V OR 5V
D1
1N4148
3
8
–
7
LT1011
2
R2
560k
+
R4
470k
NEGATIVE EDGE
TO TIMER
4
ILOW
R2 =
(2.465)(2000 )
IHI − ILOW
All battery chargers with fast charge rates require some
means to detect full charge in the battery and terminate the
high charge current. NiCd batteries are typically charged at
high current until a temperature rise or battery voltage
decrease is detected as an indication of near full charge.
The charging current is then reduced to a much lower
value and maintained as a constant trickle charge. An
intermediate “top off” current may also be used for a fixed
time period to reduce total charge time.
1
D2
1N4148
R3
430k
* TRIP CURRENT =
=
R1(VBAT)
(R2 + R3)(RS1)
(1.6k)(8.4V)
≈ 270mA
(560k + 430k)(0.05Ω)
1769 F04
Figure 5. Current Comparator for Initiating Float Time Out
Nickel-Cadmium and Nickel-Metal-Hydride Charging
The 2A Lithium-Ion Battery Charger shown in Figure 1 can
be modified to charge NiCd or NiMH batteries. For example, if a 2-level charge is needed; 1A when Q1 is on and
100mA when Q1 is off.
PROG
300Ω
1µF
NiMH batteries are similar in chemistry to NiCd but have
two differences related to charging. First, the inflection
characteristic in battery voltage as full charge is approached
is not nearly as pronounced. This makes it more difficult
to use – dV/dt as an indicator of full charge, and an
increase in battery temperature is more often used with a
temperature sensor in the battery pack. Secondly, constant trickle charge may not be recommended. Instead, a
moderate level of current is used on a pulse basis (≈ 1%
to 5% duty cycle) with the time-averaged value substituting for a constant low trickle. Please contact the Linear
Technology Applications department about charge termination circuits.
If overvoltage protection is needed, R3 and R4 can be calculated according to the procedure described in LithiumIon Charging section. The OVP pin should be grounded if
not used.
LT1769
R1
49.3k
R2
5.49k
Q1
1769 F05
Figure 6. 2-Level Charging
For 1A full current, the current sense resistor (RS1) should
be increased to 0.1Ω so that enough signal (10mV) will be
across RS1 at 0.1A trickle charge to keep charging current
accurate.
For a 2-level charger, R1 and R2 are found from:
12
(2.465)(2000 )
When a microprocessor DAC output is used to control
charge current, it must be capable of sinking current at a
compliance up to 2.5V if connected directly to the PROG pin.
Thermal Calculations
If the LT1769 is used for charging currents above 1A, a
thermal calculation should be done to ensure that junction
temperature will not exceed 125°C. Power dissipation in
the IC is caused by bias and driver current, switch resistance and switch transition losses. The GN package, with
a thermal resistance of 35°C/W, can provide a full 2A
charging current in many situations. A graph is shown in
the Typical Performance Characteristics section.
LT1769
U
U
W
U
APPLICATIONS INFORMATION
PBIAS = (3.5mA )(VIN) + 1.5mA(VBAT )
(VBAT )
2
+
VIN
SW
[7.5mA + (0.012)(IBAT )]
LT1769
C2
L1

(IBAT )(VBAT )2  1+ VBAT

30 
PDRIVER =
55(VIN)
BOOST
D2
SPIN
VX
IVX
(I ) (RSW )(VBAT ) + t V I f
PSW = BAT
( OL)( IN)( BAT )( )
VIN
1769 F07
+
10µF
2
RSW = Switch ON resistance ≈ 0.16Ω
tOL = Effective switch overlap time ≈ 10ns
f = 200kHz
Example: VIN = 19V, VBAT = 12.6V, IBAT = 2A:
(
(12.6)
+
)( )
( )
PBIAS = 3.5mA 19 + 1.5mA 12.6
2
19
[7.5mA + (0.012)(2000mA)] = 0.35W
2
PDRIVER

The average IVX required is:
PDRIVER 0.09 W
=
= 28mA
3.3V
VX
The previous example shows the dramatic drop in driver
power dissipation when the boost diode (D2) is connected
to an external 3.3V source instead of the 12.6V battery.
PDRIVER drops from 0.43W to 0.09W resulting in an
approximately 12°C drop in junction temperature.
−9
Fused-lead packages conduct most of their heat out the
leads. This makes it very important to provide as much PC
board copper around the leads as is practical. Total
thermal resistance of the package-board combination is
dominated by the characteristics of the board in the
immediate area of the package. This means both lateral
thermal resistance across the board and vertical thermal
resistance through the board to other copper layers. Each
layer acts as a thermal heat spreader that increases the
heat sinking effectiveness of extended areas of the board.
2
19
= 0.42 + 0.08 = 0.5W
Total Power in the IC is: 0.35 + 0.43 + 0.5 = 1.3W
Temperature rise will be (1.3W)(35°C/W) = 46°C. This
assumes that the LT1769 is properly heat sunk by connecting the eleven fused ground pins to expanded traces
and that the PC board has a backside or internal plane for
heat spreading.
The PDRIVER term can be reduced by connecting the boost
diode D2 (see Figure 7) to a lower system voltage (lower
than VBAT) instead of VBAT.
(IBAT )(VBAT )(VX ) 1+ V30X 
Then PDRIVER =
55(VIN )
For example, VX = 3.3V then:

(2A)(12.6V)(3.3V) 1+ 330.3V 
=
= 0.09 W
55(19V )

(2)(12.6)  1+ 1230.6 
= 0.43W
=
55(19)
(2) (0.16)(12.6) + 10 (19)(2)(200kHz)
=
PDRIVER
PSW
Figure 7. Lower VBOOST
Total board area becomes an important factor when the
area of the board drops below about 20 square inches. The
graph in Figure 8 shows thermal resistance vs board area
for 2-layer and 4-layer boards with continuous copper
planes. Note that 4-layer boards have significantly lower
thermal resistance, but both types show a rapid increase
for reduced board areas. Figure 9 shows actual measured
lead temperatures for chargers operating at full current.
13
LT1769
U
U
W
U
APPLICATIONS INFORMATION
STANDARD CONNECTION
THERMAL RESISTANCE (°C/W)
45
40
SW
C3
0.47µF
35
C3
0.47µF
BOOST
LT1769
D2
30
HIGH DUTY CYCLE CONNECTION
D2
SPIN
SENSE
VX
3V TO 6V
BAT
SENSE
BAT
CX
10µF
4-LAYER BOARD
20
VBAT
MEASURED FROM AIR AMBIENT
TO DIE USING COPPER LANDS
AS SHOWN ON DATA SHEET
15
BOOST
LT1769
SPIN
2-LAYER BOARD
25
SW
VBAT
+
+
10
0
5
20
15
25
10
BOARD AREA (IN2)
30
35
1769 F10
1769 F08
Figure 10. High Duty Cycle
Figure 8. LT1769 Thermal Resistance
HIGH DUTY CYCLE CONNECTION
VIN
LEAD TEMPERATURE ON PINS 1, 2, 3 (°C)
70
60
VIN = 19V
VBAT = 12.3V
VBOOST = 5V
2-LAYER BOARD
ROOM TEMP = 24°C
50
Q2
5 IN2 BOARD
RX
50k
D1
C2
0.47µF
D2
SW
VCC
BOOST
LT1769
SPIN
40
25 IN2 BOARD
Q1 = Si4435DY
Q2 = TP0610L
30
20
+
Q1
NOTE: PEAK DIE TEMPERATURE
WILL BE ABOUT 15°C HIGHER AT
2A CHARGE CURRENT
VX
3V TO 6V
SENSE
BAT
CX
10µF
+
0
1
0.5
1.5
CHARGE CURRENT (A)
VBAT
2
1769 F09
1769 F11
Figure 9. LT1769 Lead Temperature
Battery voltage and input voltage will affect device power
dissipation, so the data sheet power calculations must be
used to extrapolate these readings to other situations.
Vias should be used to connect board layers together.
Planes under the charger area can be cut away from the
rest of the board and connected with vias to form both a
low thermal resistance system and to act as a ground
plane for reduced EMI.
Glue-on, chip-mounted heat sinks are effective only in
moderate power applications where the PC board copper
cannot be used, or where the board size is small. They
offer very little improvement in a properly laid out multilayer board of reasonable size.
14
Figure 11. Replacing the Input Diode
Higher Duty Cycle for the LT1769 Battery Charger
Maximum duty cycle for the LT1769 is typically 90%, but
this may be too low for some applications. For example, if
an 18V ±3% adapter is used to charge ten NiMH cells, the
charger must put out approximaly 15V. A total of 1.6V is
lost in the input diode, switch resistance, inductor resistance and parasitics, so the required duty cycle is
15/16.4 = 91.4%. The duty cycle can be extended to 93%
by restricting boost voltage to 5V instead of using VBAT as
is normally done. This lower boost voltage also reduces
power dissipation in the LT1769, so it is a win-win decision. Connect an external source of 3V to 6V at VX node in
Figure 10 with a 10µF CX bypass capacitor.
LT1769
U
U
W
U
APPLICATIONS INFORMATION
Lower Dropout Voltage
For even lower dropout and/or reducing heat on the board,
the input diode D3 can be replaced with a FET (see Figure
11). Connect a P-channel FET in place of the input diode
with its gate connected to the battery causing the FET to
turn off when the input voltage goes low. The problem is
that the gate must be pumped low so that the FET is fully
turned on even when the input is only a volt or two above
the battery voltage. Also there is a turn-off speed issue.
The FET should turn off instantly when the input is dead
shorted to avoid large current surges from the battery
back through the charger into the FET. Gate capacitance
slows turn-off, so a small P-channel (Q2) is added to
discharge the gate capacitance quickly in the event of an
input short. The Q2 body diode creates the necessary
pumping action to keep the gate of Q1 low during normal
operation. Note that Q1 and Q2 have a VGS spec limit of
20V. This restricts VIN to a maximum of 20V. For low
dropout operation with VIN > 20V consult factory.
Optional Diode Connections
The typical application in Figure 1 shows a single diode
(D3) to isolate the VCC pin from the adaptor input and to
block reverse input voltage (both steady state and transient). This simple connection may be unacceptable in
situations where the system load must be powered from
the battery when the adapter input power is removed. As
shown in Figure 12, a parasitic diode exists from the SW
R7
500Ω
+
CLN
INTERNAL
PARASITIC
DIODE
RS1
SWITCH NODE
L1
VBAT
RS4
TO
SYSTEM
LOAD
+
CIN
Switch rise and fall times are under 10ns for maximum
efficiency. To minimize radiation, the catch diode, SW pin
and input bypass capacitor leads should be kept as short
as possible. A ground plane should be used under the
switching circuitry to prevent interplane coupling and to
act as a thermal spreading path. All ground pins should be
connected to expanded traces for low thermal resistance.
The fast-switching high current ground path, including the
switch, catch diode and input capacitor, should be kept
very short. Catch diode and input capacitor should be
close to the chip and terminated to the same point. This
path contains nanosecond rise and fall times with several
amps of current. The other paths contain only DC and/or
200kHz tri-wave and are less critical. Figure 13 indicates
the high speed, high current switching path. Figure 14
shows critical path layout. Contact Linear Technology for
the LT1769 circuit PCB layout or Gerber file.
ADAPTER
IN
VCC
SW
L1
C1
1µF
Layout Considerations
D3
CLP
LT1769
pin to the VCC pin in the LT1769. When the input power is
removed, this diode will become forward biased and will
provide a current path from the battery to the system load.
Because of diode power limitations, it is not recommended to power the system load through the internal
parasitic diode. To safely power the system load from the
battery, an additional Schottky diode (D4) is needed. For
minimum losses, D4 could be replaced by a low RDS(ON)
MOSFET which is turned on when the adapter power is
removed.
D4
VIN
CIN
HIGH
FREQUENCY
CIRCULATING
PATH
D1
COUT
BAT
+
1769 F13
1769 F12a
Figure 12. Modified Diode Connection
Figure 13. High Speed Switching Path
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
15
LT1769
U
U
W
U
APPLICATIONS INFORMATION
GND
CIN
D1
L1
TO
GND
GND
GND
GND
SW
BOOST
UV
GND
GND
OVP
CLP
CLN
COMP1
SENSE
GND
GND
GND
GND
VCC1
VCC2
VCC3
GND
PROG
VC
UVOUT
COMP2
BAT
SPIN
GND
TO
GND
RS1
COUT
GND
NOTE: CONNECT ALL GND PINS TO EXPANDED PC LANDS FOR PROPER HEAT SINKING
1769 F14
Figure 14. Critical Electrical and Thermal Path Layout
U
PACKAGE DESCRIPTION
Dimensions in inches (millimeters) unless otherwise noted.
GN Package
28-Lead Plastic SSOP (Narrow 0.150)
(LTC DWG # 05-08-1641)
0.015 ± 0.004
× 45°
(0.38 ± 0.10)
0.0075 – 0.0098
(0.191 – 0.249)
0.053 – 0.069
(1.351 – 1.748)
0.386 – 0.393*
(9.804 – 9.982)
0.004 – 0.009
(0.102 – 0.249)
28 27 26 25 24 23 22 21 20 19 18 17 1615
0.033
(0.838)
REF
0° – 8° TYP
0.016 – 0.050
(0.406 – 1.270)
0.008 – 0.012
(0.203 – 0.305)
0.229 – 0.244
(5.817 – 6.198)
0.0250
(0.635)
BSC
* DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
** DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
0.150 – 0.157**
(3.810 – 3.988)
GN28 (SSOP) 1098
1
2 3
4
5 6
7
8
9 10 11 12 13 14
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LTC®1325
Microprocessor-Controlled Battery Management System
Can Charge, Discharge and Gas Gauge NiCd and Lead-Acid
Batteries with Software Charging Profiles
LT1372/LT1377
500kHz/1MHz Step-Up Switching Regulators
High Frequency, Small Inductor, High Efficiency Switchers, 1.5A Switch
LT1376
500kHz Step-Down Switching Regulator
High Frequency, Small Inductor, High Efficiency Switcher, 1.5A Switch
LT1505
High Current, High Efficiency Battery Charger
94% Efficiency, Synchronous Current Mode PWM
LT1510
Constant-Voltage/Constant-Current Battery Charger
Up to 1.5A Charge Current for Lithium-Ion, NiCd and NiMH Batteries
LT1511
Constant-Voltage/Constant-Current Battery Charger
Up to 3A Charge Current for Lithium-Ion, NiCd and NiMH Batteries
LT1512/LT1513
SEPIC Battery Chargers
VIN Can Be Higher or Lower Than Battery Voltage
LTC1729
Li-Ion Battery Charger Termination Controller
Preconditioning If Cell < 2.7V, 3hr Time-Out, C/10 Detection, Temp Sensor
Pin, Charger and Battery Detection
LTC1759
SMBus Smart Battery Charger
94% Efficiency with Input Current Limiting, Up to 8A ICHG
16
Linear Technology Corporation
1769f LT/TP 0999 4K • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408)432-1900 ● FAX: (408) 434-0507 ● www.linear-tech.com
 LINEAR TECHNOLOGY CORPORATION 1999
Similar pages