FEATURES FUNCTIONAL BLOCK DIAGRAM 12-bit plus sign SAR ADC True bipolar input ranges Software-selectable input ranges ±10 V, ±5 V, ±2.5 V, 0 V to +10 V 500 kSPS throughput rate 8 analog input channels with channel sequencer Single-ended, true differential, and pseudo differential analog input capability High analog input impedance Low power: 18 mW Temperature indicator Full power signal bandwidth: 22 MHz Internal 2.5 V reference High speed serial interface Power-down modes 20-lead TSSOP package iCMOS™ process technology REFIN/OUT VDD VCC AD7327 VIN0 2.5V VREF VIN1 VIN2 VIN3 VIN4 VIN5 VIN6 VIN7 I/P MUX T/H 13-BIT SUCCESSIVE APPROXIMATION ADC TEMPERATURE INDICATOR DOUT CONTROL LOGIC AND REGISTERS CHANNEL SEQUENCER SCLK CS DIN VDRIVE AGND VSS 05401-001 Data Sheet 500 kSPS, 8-Channel, Software-Selectable, True Bipolar Input, 12-Bit Plus Sign ADC AD7327 DGND Figure 1. GENERAL DESCRIPTION serial interface that can operate at throughput rates up to 500 kSPS. The AD7327 is an 8-channel, 12-bit plus sign successive approximation ADC designed on the iCMOS (industrial CMOS) process. iCMOS is a process combining high voltage silicon with submicron CMOS and complementary bipolar technologies. It enables the development of a wide range of high performance analog ICs capable of 33 V operation in a footprint that no previous generation of high voltage parts could achieve. Unlike analog ICs using conventional CMOS processes, iCMOS components can accept bipolar input signals while providing increased performance, dramatically reduced power consumption, and reduced package size. PRODUCT HIGHLIGHTS 1 The AD7327 can accept true bipolar analog input signals. The AD7327 has four software-selectable input ranges: ±10 V, ±5 V, ±2.5 V, and 0 V to +10 V. Each analog input channel can be independently programmed to one of the four input ranges. The analog input channels on the AD7327 can be programmed to be single-ended, true differential, or pseudo differential. The ADC contains a 2.5 V internal reference. The AD7327 also allows external reference operation. If a 3 V reference is applied to the REFIN/OUT pin, the AD7327 can accept a true bipolar ±12 V analog input. Minimum ±12 V VDD and VSS supplies are required for the ±12 V input range. The ADC has a high speed 1. The AD7327 can accept true bipolar analog input signals, ±10 V, ±5 V, ±2.5 V, and 0 V to +10 V unipolar signals. 2. The eight analog inputs can be configured as eight singleended inputs, four true differential inputs, four pseudo differential inputs, or seven pseudo differential inputs. 3. 500 kSPS serial interface. SPI®-/QSPI™-/DSP-/MICROWIRE™compatible interface. 4. Low power, 18 mW, at a maximum throughput rate of 500 kSPS. 5. Channel sequencer. Table 1. Similar Devices Device Number AD7329 AD7328 AD7324 AD7323 AD7322 AD7321 Throughput Rate 1000 kSPS 1000 kSPS 1000 kSPS 500 kSPS 1000 kSPS 500 kSPS Number of bits 12-bit plus sign 12-bit plus sign 12-bit plus sign 12-bit plus sign 12-bit plus sign 12-bit plus sign Number of Channels 8 8 4 4 2 2 Protected by U.S. Patent No. 6,731,232. 1 Rev. B Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 ©2006–2013 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com Powered by TCPDF (www.tcpdf.org) IMPORTANT LINKS for the AD7327* Last content update 01/08/2014 10:20 am SIMILAR PRODUCTS & PARAMETRIC SELECTION TABLES DESIGN TOOLS, MODELS, DRIVERS & SOFTWARE Find Similar Products By Operating Parameters Low Resolution - Simultaneous Sampling 12-Bit PulSAR ADCs Low Resolution - Muxed 8/10/12/13-Bit PulSAR ADCs BeMicro FPGA Project for AD7327 with Nios driver AD7327 FMC-SDP Interposer & Evaluation Board / Xilinx KC705 Reference Design DOCUMENTATION EVALUATION KITS & SYMBOLS & FOOTPRINTS UG-419: Evaluating the AD7327/AD7328 MS-2210: Designing Power Supplies for High Speed ADC View the Evaluation Boards and Kits page for documentation and purchasing Symbols and Footprints SUGGESTED COMPANION PRODUCTS Recommended Input Buffer Amplifiers for the AD7327 For low noise and low power applications, we recommend the ADA4841-1, ADA4932-1, the dual ADA4841-2 or the low cost AD8137. For low noise and high frequency, we recommend the AD8021, ADA4899-1 or the dual AD8022. For low noise and low frequency at high supply voltages( up to +-18V), we suggest the AD8597, ADA4627-1 or the dual AD8599. For low noise and low frequency applications at medium supply voltages( up to +-13V), we suggest the AD8610 or the dual AD8620. Recommended External References for the AD7327 For a precision 2.5V reference, we recommend AD780, AD1582, ADR431 or the ADR391. For a precision 3.0V reference, we recommend AD780 or the REF193. Recommended Voltage Regulators for the AD7327 For low dropout regulators with inputs up to 5V, we recommend the low noise ADP151 or the low power ADP160. For high current switching regulators with inputs up to 5V, we recommend the low noise ADP2114. DESIGN COLLABORATION COMMUNITY Collaborate Online with the ADI support team and other designers about select ADI products. Follow us on Twitter: www.twitter.com/ADI_News Like us on Facebook: www.facebook.com/AnalogDevicesInc DESIGN SUPPORT Submit your support request here: Linear and Data Converters Embedded Processing and DSP Telephone our Customer Interaction Centers toll free: Americas: Europe: China: India: Russia: 1-800-262-5643 00800-266-822-82 4006-100-006 1800-419-0108 8-800-555-45-90 Quality and Reliability Lead(Pb)-Free Data SAMPLE & BUY AD7327 View Price & Packaging Request Evaluation Board Request Samples Check Inventory & Purchase Find Local Distributors * This page was dynamically generated by Analog Devices, Inc. and inserted into this data sheet. Note: Dynamic changes to the content on this page (labeled 'Important Links') does not constitute a change to the revision number of the product data sheet. This content may be frequently modified. AD7327 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Sequence Register ....................................................................... 23 Functional Block Diagram .............................................................. 1 Range Registers ........................................................................... 24 General Description ......................................................................... 1 Sequencer Operation ..................................................................... 25 Product Highlights ........................................................................... 1 Reference ..................................................................................... 27 Revision History ............................................................................... 2 VDRIVE ............................................................................................ 27 Specifications..................................................................................... 3 Temperature Indicator ............................................................... 27 Timing Specifications .................................................................. 7 Modes of Operation ....................................................................... 28 Absolute Maximum Ratings............................................................ 8 Normal Mode.............................................................................. 28 ESD Caution .................................................................................. 8 Full Shutdown Mode.................................................................. 28 Pin Configuration and Function Descriptions ............................. 9 Autoshutdown Mode ................................................................. 29 Typical Performance Characteristics ........................................... 10 Autostandby Mode ..................................................................... 29 Terminology .................................................................................... 14 Power vs. Throughput Rate ....................................................... 30 Theory of Operation ...................................................................... 16 Serial Interface ................................................................................ 31 Circuit Information .................................................................... 16 Microprocessor Interfacing ........................................................... 32 Converter Operation .................................................................. 16 AD7327 to ADSP-21xx .............................................................. 32 Analog Input Structure .............................................................. 17 AD7327 to ADSP-BF53x ........................................................... 32 Typical Connection Diagram ................................................... 19 Application Hints ........................................................................... 33 Analog Input ............................................................................... 19 Layout and Grounding .............................................................. 33 Driver Amplifier Choice ............................................................ 21 Power Supply Configuration .................................................... 33 Registers ........................................................................................... 22 Outline Dimensions ....................................................................... 34 Addressing Registers .................................................................. 22 Ordering Guide .......................................................................... 34 Control Register .......................................................................... 22 REVISION HISTORY 12/13—Rev. A to Rev. B Changes to Circuit Information Section and Table 6 ................ 16 Changes to Addressing Registers Section.................................... 22 Changes to Power Supply Configuration Section ...................... 33 Changes to Ordering Guide .......................................................... 34 1/10—Rev. 0 to Rev. A Change to Features and Product Highlights Sections ................. 1 Changes to Table 2 ............................................................................ 5 Change to Endnote 1 in Table 4 ...................................................... 8 Added Power Supply Configuration Section, Figure 56, and Table 16 ............................................................................................ 33 1/06—Revision 0: Initial Version Rev. B | Page 2 of 36 Data Sheet AD7327 SPECIFICATIONS VDD = 12 V to 16.5 V, VSS = −12 V to −16.5 V, VCC = 2.7 V to 5.25 V, VDRIVE = 2.7 V to 5.25 V, VREF = 2.5 V to 3.0 V internal/external, fSCLK = 10 MHz, fS = 500 kSPS, TA = TMAX to TMIN, unless otherwise noted. Table 2. Parameter 1 DYNAMIC PERFORMANCE Signal-to-Noise Ratio (SNR) 2 Signal-to-Noise + Distortion (SINAD)2 Min B Version Typ Max Unit 76 75.5 72.5 dB dB dB 72 dB 75 dB 74 76 dB dB 72.5 dB 72 Total Harmonic Distortion (THD)2 −80 dB −79 dB dB dB dB dB −82 −77 −79 −80 Peak Harmonic or Spurious Noise (SFDR)2 −81 dB −80 dB dB dB −82 −78 −80 Intermodulation Distortion (IMD)2 Second-Order Terms Third-Order Terms Aperture Delay 3 Aperture Jitter3 Common-Mode Rejection (CMRR)2 Channel-to-Channel Isolation2 Full Power Bandwidth Test Conditions/Comments FIN = 50 kHz sine wave Differential mode, VCC = 4.75 V to 5.25 V Differential mode, VCC < 4.75 V Single-ended/pseudo differential mode; ±10 V, ±2.5 V and ±5 V ranges, VCC = 4.75 V to 5.25 V Single-ended/pseudo differential mode; 0 V to 10 V VCC = 4.75 V to 5.25 V and all ranges at VCC < 4.75 V Differential mode; ±2.5 V and ±5 V ranges Differential mode; 0 V to 10 V Differential mode; ±10 V range Single-ended/pseudo differential mode; ±2.5 V and ±5 V ranges Single-ended/pseudo differential mode; 0 V to +10 V and ±10 V ranges Differential mode; ±2.5 V and ±5 V ranges Differential mode; 0 V to 10 V ranges Differential mode; ±10 V range Single-ended/pseudo differential mode; ±5 V range Single-ended/pseudo differential mode; ±2.5 V range Single-ended/pseudo differential mode; 0 V to +10 V and ±10 V ranges Differential mode; ±2.5 V and ±5 V ranges Differential mode; 0 V to 10 V ranges Differential mode; ±10 V ranges Single-ended/pseudo differential mode; ±5 V range Single-ended/pseudo differential mode; ±2.5 V range Single-ended/pseudo differential mode; 0 V to +10 V and ±10 V ranges fa = 50 kHz, fb = 30 kHz −79 dB −88 −90 7 50 −79 dB dB ns ps dB Up to 100 kHz ripple frequency; see Figure 17 −72 22 5 dB MHz MHz FIN on unselected channels up to 100 kHz; see Figure 14 At 3 dB At 0.1 dB Rev. B | Page 3 of 36 AD7327 Parameter 1 DC ACCURACY 4 Resolution No Missing Codes Data Sheet Min B Version Typ Max 13 12-bit plus sign (13 bits) 11-bit plus sign (12 bits) Test Conditions/Comments Single-ended/pseudo differential mode 1 LSB = FSR/4096, unless otherwise noted. Differential mode 1 LSB = FSR/8192, unless otherwise noted. Bits Bits Differential mode Bits Single-ended/pseudo differential mode LSB LSB LSB LSB LSB LSB LSB LSB LSB LSB LSB LSB LSB LSB LSB LSB LSB LSB LSB LSB LSB LSB Differential mode; VCC = 3 V to 5.25 V, typ for VCC = 2.7 V Single-ended/pseudo differential mode, VCC = 3 V to 5.25 V, typ for VCC = 2.7 V Single-ended/pseudo differential mode (LSB = FSR/8192) Differential mode; guaranteed no missing codes to 13 bits Single-ended mode; guaranteed no missing codes to 12 bits Single-ended/pseudo differential mode (LSB = FSR/8192) Single-ended/pseudo differential mode Differential mode Single-ended/pseudo differential mode Differential mode Single-ended/pseudo differential mode Differential mode Single-ended/pseudo differential mode Differential mode Single-ended/pseudo differential mode Differential mode Single-ended/pseudo differential mode Differential mode Single-ended/pseudo differential mode Differential mode Single-ended/pseudo differential mode Differential mode Single-ended/pseudo differential mode Differential mode Single-ended/pseudo differential mode Differential mode ±10 V Reference = 2.5 V; see Table 6 VDD = +10 V min, VSS = −10 V min, VCC = +2.7 V to +5.25 V ±5 ±2.5 0 to 10 V V V ±3.5 ±6 ±5 +3/−5 V V V V Integral Nonlinearity2 ±1.1 ±1 −0.7/+1.2 Differential Nonlinearity2 LSB −0.9/+1.2 LSB ±0.9 LSB −0.7/+1 Offset Error2, 5 LSB −4/+9 −7/+10 ±0.6 ±0.5 ±8 ±14 ±0.5 ±0.5 ±4 ±7 ±0.5 ±0.5 ±8.5 ±7.5 ±0.5 ±0.5 ±4 ±6 ±0.5 ±0.5 Offset Error Match2, 5 Gain Error2, 5 Gain Error Match2, 5 Positive Full-Scale Error2, 6 Positive Full-Scale Error Match2, 6 Bipolar Zero Error2, 6 Bipolar Zero Error Match2, 6 Negative Full-Scale Error2, 6 Negative Full-Scale Error Match2, 6 ANALOG INPUT Input Voltage Ranges (Programmed via Range Registers) Unit Pseudo Differential VIN(−) Input Range Rev. B | Page 4 of 36 VDD = +5 V min, VSS = −5 V min, VCC = +2.7 V to +5.25 V VDD = +5 V min, VSS = −5 V min, VCC = +2.7 V to +5.25 V VDD = +10 V min, VSS = AGND min, VCC = +2.7 V to +5.25 V VDD = +16.5 V, VSS = −16.5 V, VCC = +5 V; see Figure 40 and Figure 41 Reference = 2.5 V; range = ±10 V Reference = 2.5 V; range = ±5 V Reference = 2.5 V; range = ±2.5 V Reference = 2.5 V; range = 0 V to +10 V Data Sheet Parameter 1 DC Leakage Current AD7327 B Version Typ Min Reference Output Impedance LOGIC INPUTS Input High Voltage, VINH Input Low Voltage, VINL Input Current, IIN Input Capacitance, CIN3 LOGIC OUTPUTS Output High Voltage, VOH 2.5 3 ±1 ±5 V µA pF V mV ±10 mV 25 ppm/°C 10 2.5 3 7 0.8 0.4 ±1 10 VDRIVE − 0.2 V 0.4 ±1 5 V V V µA pF VCC = 4.75 V to 5.25 V VCC = 2.7 to 3.6 V VIN = 0 V or VDRIVE V ISOURCE = 200 µA V µA pF ISINK = 200 µA Straight natural binary Twos complement 12 −12 2.7 2.7 Test Conditions/Comments VIN = VDD or VSS Per input channel, VIN = VDD or VSS When in track, ±10 V range When in track, ±5 V and 0 V to +10 V ranges When in track, ±2.5 V range When in hold, all ranges ppm/°C Ω 2.4 Output Low Voltage, VOL Floating-State Leakage Current Floating-State Output Capacitance3 Output Coding CONVERSION RATE Conversion Time Track-and-Hold Acquisition Time2, 3 Throughput Rate POWER REQUIREMENTS VDD VSS VCC VDRIVE Normal Mode (Static) Normal Mode (Operational) IDD ISS ICC and IDRIVE Autostandby Mode (Dynamic) IDD ISS ICC and IDRIVE Unit nA nA pF pF pF pF 3 13.5 16.5 21.5 3 Input Capacitance3 REFERENCE INPUT/OUTPUT Input Voltage Range Input DC Leakage Current Input Capacitance Reference Output Voltage Reference Output Voltage Error at 25°C Reference Output Voltage TMIN to TMAX Reference Temperature Coefficient Max ±80 Coding bit set to 1 in control register Coding bit set to 0 in control register 1.6 305 µs ns 16 SCLK cycles with SCLK = 10 MHz Full-scale step input; see the Terminology section 500 kSPS 16.5 −16.5 5.25 5.25 V V V V mA See the Serial Interface section Digital inputs = 0 V or VDRIVE See Table 6 See Table 6 See Table 6 0.9 180 205 2.2 µA µA mA 100 110 0.75 µA µA mA Rev. B | Page 5 of 36 VDD/VSS = ±16.5 V, VCC/VDRIVE = 5.25 V fSAMPLE = 500 kSPS VDD = 16.5 V VSS = −16.5 V VCC/VDRIVE = 5.25 V fSAMPLE = 250 kSPS VDD = 16.5 V VSS = −16.5 V VCC/VDRIVE = 5.25 V AD7327 Parameter 1 Autoshutdown Mode (Static) IDD ISS ICC and IDRIVE Full Shutdown Mode IDD ISS ICC and IDRIVE POWER DISSIPATION Normal Mode (Operational) Full Shutdown Mode Data Sheet Min B Version Typ Max Unit 1 1 1 µA µA µA 1 1 1 µA µA µA Test Conditions/Comments SCLK on or off VDD = 16.5 V VSS = −16.5 V VCC/VDRIVE = 5.25 V SCLK on or off VDD = 16.5 V VSS = −16.5 V VCC/VDRIVE = 5.25 V 18 38.25 mW µW VDD = +16.5 V, VSS = −16.5 V, VCC = +5.25 V VDD = +16.5 V, VSS = −16.5 V, VCC = +5.25 V Temperature range is −40°C to +85°C. See the Terminology section. 3 Sample tested during initial release to ensure compliance. 4 For dc accuracy specifications, the LSB size for differential mode is FSR/8192. For single-ended mode/pseudo differential mode, the LSB size is FSR/4096, unless otherwise noted. 5 Unipolar 0 V to 10 V range with straight binary output coding. 6 Bipolar range with twos complement output coding. 1 2 Rev. B | Page 6 of 36 Data Sheet AD7327 TIMING SPECIFICATIONS VDD = 12 V to 16.5 V, VSS = −12 V to −16.5 V, VCC = 2.7 V to 5.25 V, VDRIVE = 2.7 V to 5.25 V, VREF = 2.5 V to 3.0 V internal/external, TA = TMAX to TMIN. Timing specifications apply with a 32 pF load, unless otherwise noted. 1 Table 3. Parameter fSCLK tCONVERT tQUIET t1 t2 2 t3 t4 t5 t6 t7 t8 t9 t10 tPOWER-UP 2 Unit kHz min MHz max ns max ns min ns min ns min ns min ns max ns max ns min ns min ns min ns max ns min ns min ns min ns max µs max 25 µs typ 25 Description VDRIVE ≤ VCC tSCLK = 1/fSCLK Minimum time between end of serial read and next falling edge of CS Minimum CS pulse width CS to SCLK set-up time; bipolar input ranges (±10 V, ±5 V, ±2.5 V) Unipolar input range (0 V to 10 V) Delay from CS until DOUT three-state disabled Data access time after SCLK falling edge SCLK low pulse width SCLK high pulse width SCLK to data valid hold time SCLK falling edge to DOUT high impedance SCLK falling edge to DOUT high impedance DIN set-up time prior to SCLK falling edge DIN hold time after SCLK falling edge Power-up from autostandby Power-up from full shutdown/autoshutdown mode, internal reference Power-up from full shutdown/autoshutdown mode, external reference Sample tested during initial release to ensure compliance. All input signals are specified with tr = tf = 5 ns (10% to 90% of VDRIVE) and timed from a voltage level of 1.6 V. When using the 0 V to 10 V unipolar range, running at 500 kSPS throughput rate with t2 at 20 ns, the mark space ratio needs to be limited to 50:50. t1 CS tCONVERT t2 SCLK t6 1 2 4 3 3 IDENTIFICATION BITS t3 ADD1 DOUT THREE- ADD2 t9 STATE DIN WRITE REG SEL1 ADD0 SIGN t4 14 13 5 DB10 DB11 16 15 t5 t7 DB2 t8 DB1 t10 REG SEL2 tQUIET DB0 THREE-STATE MSB LSB Figure 2. Serial Interface Timing Diagram Rev. B | Page 7 of 36 DON’T CARE 05401-002 1 Limit at TMIN, TMAX VCC < 4.75 V VCC = 4.75 V to 5.25 V 50 50 10 10 16 × tSCLK 16 × tSCLK 75 60 12 5 25 20 45 35 26 14 57 43 0.4 × tSCLK 0.4 × tSCLK 0.4 × tSCLK 0.4 × tSCLK 13 8 40 22 10 9 4 4 2 2 750 750 500 500 AD7327 ABSOLUTE MAXIMUM RATINGS TA = 25°C, unless otherwise noted. Table 4. Parameter VDD to AGND, DGND VSS to AGND, DGND VDD to VCC VCC to AGND, DGND VDRIVE to AGND, DGND AGND to DGND Analog Input Voltage to AGND 1 Digital Input Voltage to DGND Digital Output Voltage to GND REFIN to AGND Input Current to Any Pin Except Supplies 2 Operating Temperature Range Storage Temperature Range Junction Temperature TSSOP Package θJA Thermal Impedance θJC Thermal Impedance Pb-Free Temperature, Soldering Reflow ESD Rating −0.3 V to +16.5 V +0.3 V to −16.5 V VCC − 0.3 V to 16.5 V −0.3 V to +7 V −0.3 V to +7 V −0.3 V to +0.3 V VSS − 0.3 V to VDD + 0.3 V −0.3 V to +7 V −0.3 V to VDRIVE + 0.3 V −0.3 V to VCC + 0.3 V ±10 mA Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION −40°C to +85°C −65°C to +150°C 150°C 143°C/W 45°C/W 260(0)°C 2.5 kV If the analog inputs are driven from alternative VDD and VSS supply circuitry, Schottky diodes should be placed in series with the AD7327 VDD and VSS supplies. See Power Supply Configuration section. 2 Transient currents of up to 100 mA do not cause SCR latch-up. 1 Rev. B | Page 8 of 36 Data Sheet AD7327 CS 1 20 SCLK DIN 2 19 DGND DGND 3 18 DOUT 17 VDRIVE AGND 4 REFIN/OUT 5 AD7327 TOP VIEW (Not to Scale) 16 VCC VSS 6 15 VDD VIN0 7 14 VIN2 VIN1 8 13 VIN3 VIN4 9 12 VIN6 VIN5 10 11 VIN7 05401-003 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS Figure 3. TSSOP Pin Configuration Table 5. Pin Function Descriptions Pin No. 1 Mnemonic CS 2 DIN 3, 19 DGND 4 AGND 5 REFIN/OUT 6 7, 8, 14, 13, 9, 10, 12, 11 VSS VIN0 to VIN7 15 16 VDD VCC 17 VDRIVE 18 DOUT 20 SCLK Description Chip Select. Active low logic input. This input provides the dual function of initiating conversions on the AD7327 and frames the serial data transfer. Data In. Data to be written to the on-chip registers is provided on this input and is clocked into the AD7327 on the falling edge of SCLK (see the Registers section). Digital Ground. Ground reference point for all digital circuitry on the AD7327. The DGND and AGND voltages ideally should be at the same potential and must not be more than 0.3 V apart, even on a transient basis. Analog Ground. Ground reference point for all analog circuitry on the AD7327. All analog input signals and any external reference signal should be referred to this AGND voltage. The AGND and DGND voltages ideally should be at the same potential and must not be more than 0.3 V apart, even on a transient basis. Reference Input/Reference Output. The on-chip reference is available on this pin for external use to the AD7327. The nominal internal reference voltage is 2.5 V, which appears at this pin. A 680 nF capacitor should be placed on the reference pin (see the Reference section). Alternatively, the internal reference can be disabled and an external reference applied to this input. On power-up, the external reference mode is the default condition. Negative Power Supply Voltage. This is the negative supply voltage for the analog input section. Analog Input 0 to Analog Input 7. The analog inputs are multiplexed into the on-chip track-and-hold. The analog input channel for conversion is selected by programming the channel address Bit ADD2 through Bit ADD0 in the control register. The inputs can be configured as eight single-ended inputs, four true differential input pairs, four pseudo differential inputs, or seven pseudo differential inputs. The configuration of the analog inputs is selected by programming the mode bits, Bit Mode 1 and Bit Mode 0, in the control register. The input range on each input channel is controlled by programming the range registers. Input ranges of ±10 V, ±5 V, ±2.5 V, and 0 V to +10 V can be selected on each analog input channel when a +2.5 V reference voltage is used (see the Registers section). Positive Power Supply Voltage. This is the positive supply voltage for the analog input section. Analog Supply Voltage, 2.7 V to 5.25 V. This is the supply voltage for the ADC core on the AD7327. This supply should be decoupled to AGND. Logic Power Supply Input. The voltage supplied at this pin determines at what voltage the interface operates. This pin should be decoupled to DGND. The voltage at this pin may be different to that at VCC, but it should not exceed VCC by more than 0.3 V. Serial Data Output. The conversion output data is supplied to this pin as a serial data stream. The bits are clocked out on the falling edge of the SCLK input, and 16 SCLKs are required to access the data. The data stream consists of three channel identification bits, the sign bit, and 12 bits of conversion data. The data is provided MSB first (see the Serial Interface section). Serial Clock, Logic Input. A serial clock input provides the SCLK used for accessing the data from the AD7327. This clock is also used as the clock source for the conversion process. Rev. B | Page 9 of 36 AD7327 TYPICAL PERFORMANCE CHARACTERISTICS 1.0 0 4096 POINT FFT VCC = VDRIVE = 5V VDD, VSS = ±15V TA = 25°C INT/EXT 2.5V REFERENCE ±10V RANGE FIN = 50kHz SNR = 77.30dB SINAD = 76.85dB THD = –86.96dB SFDR = –88.22dB SNR (dB) –40 –60 –80 0.6 0.4 INL ERROR (LSB) –20 VCC = VDRIVE = 5V INT/EXT 2.5V REFERENCE TA = 25°C ±10V RANGE VDD, VSS = ±15V +INL = +0.55LSB –INL = –0.68LSB 0.8 0.2 0 –0.2 –0.4 –100 –0.6 –120 0 50 100 150 200 250 FREQUENCY (kHz) 05401-004 –1.0 –140 0 Figure 4. FFT True Differential Mode 8192 1024 2048 3072 4096 5120 6144 7168 512 1536 2560 3584 4608 5632 6656 7680 CODE 05401-007 –0.8 Figure 7. Typical INL True Differential Mode 1.0 0 –60 –80 –100 0.4 0.2 0 –0.2 –0.4 –0.8 –120 0 50 100 150 200 250 FREQUENCY (kHz) 05401-005 –1.0 –140 VCC = VDRIVE = 5V ±10V RANGE TA = 25°C +DNL = +0.79LSB –DNL = –0.38LSB VDD, VSS = ±15V INT/EXT 2.5V REFERENCE –0.6 0 8192 1024 2048 3072 4096 5120 6144 7168 512 1536 2560 3584 4608 5632 6656 7680 CODE 05401-043 –40 0.6 DNL ERROR (LSB) –20 SNR (dB) 0.8 4096 POINT FFT VCC = VDRIVE = 5V VDD, VSS = ±15V TA = 25°C INT/EXT 2.5V REFERENCE ±10V RANGE FIN = 50kHz SNR = 74.67dB SINAD = 74.03dB THD = –82.68dB SFDR = –85.40dB Figure 8. Typical DNL Single-Ended Mode Figure 5. FFT Single-Ended Mode 1.0 1.0 0.8 0.8 0.6 INL ERROR (LSB) 0.4 0.4 0.2 0 –0.2 –0.8 –1.0 0 8192 1024 2048 3072 4096 5120 6144 7168 512 1536 2560 3584 4608 5632 6656 7680 CODE 0 –0.2 VCC = VDRIVE = 5V TA = 25°C VDD, VSS = ±15V –0.6 INT/EXT 2.5V REFERENCE ±10V RANGE –0.8 +INL = +0.87LSB –INL = –0.49LSB –1.0 0 8192 1024 2048 3072 4096 5120 6144 7168 512 1536 2560 3584 4608 5632 6656 7680 CODE Figure 9. Typical INL Single-Ended Mode Figure 6. Typical DNL True Differential Mode Rev. B | Page 10 of 36 05401-044 –0.6 0.2 –0.4 VCC = VDRIVE = 5V TA = 25°C VDD, VSS = ±15V INT/EXT 2.5V REFERENCE ±10V RANGE +DNL = +0.72LSB –DNL = –0.22LSB –0.4 05401-006 DNL ERROR (LSB) 0.6 Data Sheet AD7327 –50 75 ±2.5V SE 70 ±10V SE ±10V DIFF –75 0V TO +10V DIFF –80 ±5V SE 0V TO +10V SE 60 ±2.5V DIFF –90 –100 10 100 1000 ANALOG INPUT FREQUENCY (kHz) 50 10 –50 0V TO +10V SE ±10V SE –70 ±10V DIFF –75 0V TO +10V DIFF –80 ±5V SE –85 ±5V DIFF –90 ±2.5V SE –95 –55 VCC = 3V –60 VCC = 5V –65 –70 –75 –80 VDD/VSS = ±12V SINGLE-ENDED MODE fS = 500kSPS TA = 25°C 50kHz ON SELECTED CHANNEL –85 –90 ±2.5V DIFF 1000 05401-061 100 ANALOG INPUT FREQUENCY (kHz) –95 100 0 200 80 10k ±5V DIFF ±2.5V DIFF ±5V SE ±2.5V SE NUMBER OF OCCURRENCES ±10V DIFF ±10V SE 65 0V TO +10V SE 60 VCC = VDRIVE = 3V VDD/VSS = ±12V TA = 25°C fS = 500kSPS INTERNAL REFERENCE 100 1000 ANALOG INPUT FREQUENCY (kHz) 8k 7k 500 600 Figure 12. SINAD vs. Analog Input Frequency for Single-Ended (SE) and True Differential Mode (Diff) at 3 V VCC VCC = 5V VDD/VSS = ±12V RANGE = ±10V 10k SAMPLES TA = 25°C 6k 5k 4k 3k 2k 1k 05401-062 55 9469 9k 0V TO +10V DIFF 70 400 Figure 14. Channel-to-Channel Isolation Figure 11. THD vs. Analog Input Frequency for Single-Ended (SE) and True Differential Mode (Diff) at 5 V VCC 75 300 FREQUENCY OF INPUT NOISE (kHz) 05401-012 THD (dB) CHANNEL-TO-CHANNEL ISOLATION (dB) VCC = VDRIVE = 5V VDD/VSS = ±12V TA = 25°C fS = 500kSPS INTERNAL REFERENCE –65 SINAD (dB) 1000 Figure 13. SINAD vs. Analog Input Frequency for Single-Ended (SE) and True Differential Mode (Diff) at 5 V VCC –50 50 10 100 ANALOG INPUT FREQUENCY (kHz) Figure 10. THD vs. Analog Input Frequency for Single-Ended (SE) and True Differential Mode (Diff) at 3 V VCC –100 10 VCC = VDRIVE = 5V VDD/VSS = ±12V TA = 25°C fS = 500kSPS INTERNAL REFERENCE 55 ±2.5V SE –95 –60 ±10V SE 65 ±5V DIFF –85 ±10V DIFF 0V TO +10V DIFF 05401-063 –70 0 0 –2 228 –1 303 0 1 0 2 CODE Figure 15. Histogram of Codes, True Differential Mode Rev. B | Page 11 of 36 05401-013 THD (dB) –65 –55 ±5V SE 0V TO +10V SE SINAD (dB) –60 ±5V DIFF ±2.5V DIFF 05401-060 –55 80 VCC = VDRIVE = 3V VDD/VSS = ±12V TA = 25°C fS = 500kSPS INTERNAL REFERENCE AD7327 8k 2.0 7600 VCC = 5V VDD/VSS = ±12V RANGE = ±10V 10k SAMPLES TA = 25°C 6k 1.5 1.0 INL ERROR (LSB) 5k 4k 3k 0.5 INL = 500kSPS 0 –0.5 –1.0 1165 0 23 –3 –2 –1 0 11 0 2 3 1 –2.0 05401-014 0 ±5V RANGE VCC = VDRIVE = 5V INTERNAL REFERENCE SINGLE-ENDED MODE –1.5 1k CODE 5 –50 –55 –55 –60 –60 –65 –65 CMRR (dB) PSRR (dB) VCC = 5V –75 VCC = 3V –85 0 200 400 600 800 1000 1200 VCC = 5V VCC = 3V –75 VDD = 12V –80 VSS = –12V 0 200 400 600 800 –50 –55 –60 1.0 –65 0.5 THD (dB) DNL = 500kSPS 0 –0.5 VCC = VDRIVE = 5V VDD/VSS = ±12V TA = 25°C INTERNAL REF RANGE = ±10V AND ±2.5V fS = 500kSPS DIFFERENTIAL MODE ±5V RANGE VCC = VDRIVE = 5V INTERNAL REFERENCE SINGLE-ENDED MODE –70 –75 ±2.5V RANGE RIN = 9000Ω RIN = 5500Ω RIN = 2000Ω RIN = 100Ω RIN = 12Ω –80 –90 –95 11 13 15 17 ±VDD/VSS SUPPLY VOLTAGE (V) Figure 18. DNL Error vs. Supply Voltage at 500 kSPS 19 –100 10 05401-049 9 1200 ±10V RANGE RIN = 4000Ω RIN = 3000Ω RIN = 2000Ω RIN = 1000Ω RIN = 100Ω RIN = 12Ω –85 –1.0 7 1000 SUPPLY RIPPLE FREQUENCY (kHz) 1.5 DNL ERROR (LSB) 100mV p-p SINE WAVE ON EACH SUPPLY NO DECOUPLING SINGLE-ENDED MODE fS = 500kSPS –70 –100 2.0 5 19 Figure 20. PSRR vs. Supply Ripple Frequency Without Supply Decoupling Figure 17. CMRR vs. Common-Mode Ripple Frequency –1.5 17 –95 RIPPLE FREQUENCY (kHz) –2.0 15 –90 05401-055 –95 –100 13 –85 DIFFERENTIAL MODE FIN = 50kHz VDD/VSS = ±12V fS = 500kSPS TA = 25°C –90 11 Figure 19. INL Error vs. Supply Voltage at 500 kSPS –50 –80 9 ±VDD/VSS SUPPLY VOLTAGE (V) Figure 16. Histogram of Codes, Single-Ended Mode –70 7 05401-054 1201 05401-050 2k 100 INPUT FREQUENCY (kHz) 1000 05401-064 NUMBER OF OCCURENCES 7k Figure 21. THD vs. Analog Input Frequency for Various Source Impedances, True Differential Mode Rev. B | Page 12 of 36 Data Sheet AD7327 –50 THD (dB) VCC = VDRIVE = 5V –55 VDD/VSS = ±12V TA = 25°C –60 INTERNAL REF RANGE = ±10V AND ±2.5V –65 fS = 500kSPS SINGLE-ENDED MODE ±10V RANGE RIN = 4000Ω RIN = 2000Ω RIN = 1000Ω RIN = 100Ω RIN = 50Ω –70 –75 ±2.5V RANGE RIN = 4700Ω RIN = 3000Ω RIN = 1000Ω RIN = 100Ω RIN = 50Ω –80 –85 –90 100 INPUT FREQUENCY (kHz) 1000 05401-065 –95 –100 10 Figure 22. THD vs. Analog Input Frequency for Various Source Impedances, Single-Ended Mode Rev. B | Page 13 of 36 AD7327 TERMINOLOGY Differential Nonlinearity This is the difference between the measured and the ideal 1 LSB change between any two adjacent codes in the ADC. Integral Nonlinearity This is the maximum deviation from a straight line passing through the endpoints of the ADC transfer function. The endpoints of the transfer function are zero scale (a point 1 LSB below the first code transition) and full scale (a point 1 LSB above the last code transition). Offset Code Error This applies to straight binary output coding. It is the deviation of the first code transition (00 ... 000) to (00 ... 001) from the ideal, that is, AGND + 1 LSB. Offset Error Match This is the difference in offset error between any two input channels. Gain Error This applies to straight binary output coding. It is the deviation of the last code transition (111 ... 110) to (111 ... 111) from the ideal (that is, 4 × VREF − 1 LSB, 2 × VREF − 1 LSB, VREF −1 LSB) after adjusting for the offset error. Gain Error Match This is the difference in gain error between any two input channels. Bipolar Zero Code Error This applies when using twos complement output coding and a bipolar analog input. It is the deviation of the midscale transition (all 1s to all 0s) from the ideal input voltage, that is, AGND − 1 LSB. Bipolar Zero Code Error Match This refers to the difference in bipolar zero code error between any two input channels. Positive Full-Scale Error This applies when using twos complement output coding and any of the bipolar analog input ranges. It is the deviation of the last code transition (011…110) to (011…111) from the ideal (4 × VREF − 1 LSB, 2 × VREF − 1 LSB, VREF − 1 LSB) after adjusting for the bipolar zero code error. Positive Full-Scale Error Match This is the difference in positive full-scale error between any two input channels. Negative Full-Scale Error This applies when using twos complement output coding and any of the bipolar analog input ranges. This is the deviation of the first code transition (10 ... 000) to (10 ... 001) from the ideal (that is, −4 × VREF + 1 LSB, −2 × VREF + 1 LSB, −VREF + 1 LSB) after adjusting for the bipolar zero code error. Negative Full-Scale Error Match This is the difference in negative full-scale error between any two input channels. Track-and-Hold Acquisition Time The track-and-hold amplifier returns into track mode after the 14th SCLK rising edge. Track-and-hold acquisition time is the time required for the output of the track-and-hold amplifier to reach its final value, within ±½ LSB, after the end of a conversion. For the ±2.5 V range, the specified acquisition time is the time required for the track-and-hold amplifier to settle to within ±1 LSB. Signal to (Noise + Distortion) Ratio This is the measured ratio of signal to (noise + distortion) at the output of the ADC. The signal is the rms amplitude of the fundamental. Noise is the sum of all non-fundamental signals up to half the sampling frequency (fS/2), excluding dc. The ratio is dependent on the number of quantization levels in the digitization process. The more levels, the smaller the quantization noise. Theoretically, the signal to (noise + distortion) ratio for an ideal N-bit converter with a sine wave input is given by Signal to (Noise + Distortion) = (6.02 N + 1.76) dB For a 13-bit converter, this is 80.02 dB. Total Harmonic Distortion Total harmonic distortion (THD) is the ratio of the rms sum of harmonics to the fundamental. For the AD7327, it is defined as THD(dB) = 20 log V2 2 + V3 2 + V 4 2 + V5 2 + V6 2 V1 where V1 is the rms amplitude of the fundamental, and V2, V3, V4, V5, and V6 are the rms amplitudes of the second through the sixth harmonics. Peak Harmonic or Spurious Noise Peak harmonic or spurious noise is defined as the ratio of the rms value of the next largest component in the ADC output spectrum (up to fS/2, excluding dc) to the rms value of the fundamental. Normally, the value of this specification is determined by the largest harmonic in the spectrum, but for ADCs where the harmonics are buried in the noise floor, the largest harmonic could be a noise peak. Rev. B | Page 14 of 36 Data Sheet AD7327 Channel-to-Channel Isolation Channel-to-channel isolation is a measure of the level of crosstalk between any two channels. It is measured by applying a full-scale, 100 kHz sine wave signal to all unselected input channels and determining the degree to which the signal attenuates in the selected channel with a 50 kHz signal. Figure 14 shows the worstcase across all eight channels for the AD7327. The analog input range is programmed to be the same on all channels. Intermodulation Distortion With inputs consisting of sine waves at two frequencies, fa and fb, any active device with nonlinearities creates distortion products at sum and difference frequencies of mfa ± nfb, where m, n = 0, 1, 2, 3, and so on. Intermodulation distortion terms are those for which neither m nor n are equal to 0. For example, the second-order terms include (fa + fb) and (fa − fb), whereas the third-order terms include (2fa + fb), (2fa − fb), (fa + 2fb), and (fa − 2fb). The AD7327 is tested using the CCIF standard where two input frequencies near the top end of the input bandwidth are used. In this case, the second-order terms are usually distanced in frequency from the original sine waves, whereas the third-order terms are usually at a frequency close to the input frequencies. As a result, the second- and third-order terms are specified separately. The calculation of the intermodulation distortion is per the THD specification, where it is the ratio of the rms sum of the individual distortion products to the rms amplitude of the sum of the fundamentals expressed in decibels. PSR (Power Supply Rejection) Variations in power supply affect the full-scale transition but not the linearity of the converter. Power supply rejection is the maximum change in the full-scale transition point due to a change in power supply voltage from the nominal value (see the Typical Performance Characteristics section). CMRR (Common-Mode Rejection Ratio) CMRR is defined as the ratio of the power in the ADC output at full-scale frequency, f, to the power of a 100 mV sine wave applied to the common-mode voltage of the VIN+ and VIN− frequency, fS, as CMRR (dB) = 10 log (Pf/PfS) where Pf is the power at frequency f in the ADC output, and PfS is the power at frequency fS in the ADC output (see Figure 17). Rev. B | Page 15 of 36 AD7327 THEORY OF OPERATION The AD7327 requires VDD and VSS dual supplies for the high voltage analog input structures. These supplies must be equal to or greater than the analog input range. See Table 6 for the requirements of these supplies for each analog input range. The AD7327 requires a low voltage 2.7 V to 5.25 V VCC supply to power the ADC core. Table 6. Reference and Supply Requirements for Each Analog Input Range Selected Analog Input Range (V) ±10 ±5 ±2.5 0 to +10 1 Reference Voltage (V) 2.5 3.0 2.5 3.0 2.5 3.0 2.5 3.0 Full-Scale Input Range (V) ±10 ±12 ±5 ±6 ±2.5 ±3 0 to +10 0 to +12 AVCC (V) 3/5 3/5 3/5 3/5 3/5 3/5 3/5 3/5 Minimum VDD/VSS (V)1 ±10 ±12 ±5 ±6 ±5 ±5 +10/AGND +12/AGND Guaranteed performance for VDD = 12 V to 16.5 V and VSS = −12 V to −16.5 V. The performance specifications are guaranteed for VDD = 12 V to 16.5 V and VSS = −12 V to −16.5 V. With VDD and VSS supplies outside this range, the AD7327 is fully functional but performance is not guaranteed. It may be necessary to decrease the throughput rate when the AD7327 is configured with the minimum VDD and VSS supplies to meet the performance specifications (see the Typical Performance Characteristics section). Figure 31 shows the change in THD as the VDD and VSS supplies are reduced. For ac performance at the maximum throughput rate, the THD degrades slightly as VDD and VSS are reduced. It might, therefore, be necessary to reduce the throughput rate when using minimum VDD and VSS supplies so that there is less degradation of THD and the specified performance can be maintained. The degradation is due to an increase in the on resistance of the input multiplexer when the VDD and VSS supplies are reduced. Figure 18 and Figure 19 show the change in INL and DNL as the VDD and VSS voltages are varied. For dc performance when operating at the maximum throughput rate, as the VDD and VSS supply voltages are reduced, the typical INL and DNL error remains constant. The serial clock input accesses data from the part and provides the clock source for the successive approximation ADC. The AD7327 has an on-chip 2.5 V reference; however, the AD7327 can also work with an external reference. On power-up, the external reference operation is the default option. If the internal reference is the preferred option, the user must write to the reference bit in the control register to select the internal reference operation. The AD7327 also features power-down options to allow power savings between conversions. The power-down modes are selected by programming the on-chip control register, as described in the Modes of Operation section. CONVERTER OPERATION The AD7327 is a successive approximation ADC built around two capacitive DACs. Figure 23 and Figure 24 show simplified schematics of the ADC in single-ended mode during the acquisition and conversion phases, respectively. Figure 25 and Figure 26 show simplified schematics of the ADC in differential mode during acquisition and conversion phases, respectively. The ADC is composed of control logic, a SAR, and capacitive DACs. In Figure 23 (the acquisition phase), SW2 is closed and SW1 is in Position A, the comparator is held in a balanced condition, and the sampling capacitor array acquires the signal on the input. CAPACITIVE DAC B VIN0 COMPARATOR CS A SW1 CONTROL LOGIC SW2 AGND 05401-017 The AD7327 is a fast, 8-channel, 12-bit plus sign, bipolar input, serial ADC. The AD7327 can accept bipolar input ranges that include ±10 V, ±5 V, and ±2.5 V; it can also accept a 0 V to +10 V unipolar input range. A different analog input range can be programmed on each analog input channel via the on-chip registers. The AD7327 has a high speed serial interface that can operate at throughput rates up to 500 kSPS. The analog inputs can be configured as eight single-ended inputs, four true differential inputs, four pseudo differential inputs, or seven pseudo differential inputs. Selection can be made by programming the mode bits, Mode 0 and Mode 1, in the control register. Figure 23. ADC Acquisition Phase (Single-Ended) When the ADC starts a conversion (Figure 24), SW2 opens and SW1 moves to Position B, causing the comparator to become unbalanced. The control logic and the charge redistribution DAC are used to add and subtract fixed amounts of charge from the capacitive DAC to bring the comparator back into a balanced condition. When the comparator is rebalanced, the conversion is complete. The control logic generates the ADC output code. CAPACITIVE DAC B VIN0 COMPARATOR CS A SW1 SW2 CONTROL LOGIC AGND Figure 24. ADC Conversion Phase (Single-Ended) Rev. B | Page 16 of 36 05401-018 CIRCUIT INFORMATION Data Sheet AD7327 Figure 25 shows the differential configuration during the acquisition phase. For the conversion phase, SW3 opens and SW1 and SW2 move to Position B (see Figure 26). The output impedances of the source driving the VIN+ and VIN− pins must match; otherwise, the two inputs have different settling times, resulting in errors. A SW1 A SW2 B CONTROL LOGIC SW3 100...010 100...001 100...000 CS VREF CAPACITIVE DAC 000...001 000...000 111...111 –FSR/2 + 1LSB AGND + 1LSB Figure 25. ADC Differential Configuration During Acquisition Phase AGND – 1LSB +FSR/2 – 1LSB BIPOLAR RANGES +FSR – 1LSB UNIPOLAR RANGE ANALOG INPUT 05401-021 VIN– 05401-019 VIN+ COMPARATOR CS B 011...111 011...110 ADC CODE CAPACITIVE DAC The ideal transfer characteristic for the AD7327 when twos complement coding is selected is shown in Figure 27. The ideal transfer characteristic for the AD7327 when straight binary coding is selected is shown in Figure 28. Figure 27. Twos Complement Transfer Characteristic CAPACITIVE DAC CONTROL LOGIC CS CAPACITIVE DAC 000...010 000...001 000...000 Figure 26. ADC Differential Configuration During Conversion Phase Output Coding The AD7327 default output coding is set to twos complement. The output coding is controlled by the coding bit in the control register. To change the output coding to straight binary coding, the coding bit in the control register must be set. When operating in sequence mode, the output coding for each channel in the sequence is the value written to the coding bit during the last write to the control register. Transfer Functions The designed code transitions occur at successive integer LSB values (that is, 1 LSB, 2 LSB, and so on). The LSB size is dependent on the analog input range selected. Table 7. LSB Sizes for Each Analog Input Range Input Range ±10 V ±5 V ±2.5 V 0 V to +10 V Full-Scale Range/8192 Codes 20 V 10 V 5V 10 V 011...111 LSB Size 2.441 mV 1.22 mV 0.61 mV 1.22 mV –FSR/2 + 1LSB +FSR/2 – 1LSB BIPOLAR RANGES AGND + 1LSB +FSR – 1LSB UNIPOLAR RANGE ANALOG INPUT 05401-022 VREF 111...000 Figure 28. Straight Binary Transfer Characteristic ANALOG INPUT STRUCTURE The analog inputs of the AD7327 can be configured as singleended, true differential, or pseudo differential via the control register mode bits (see Table 9). The AD7327 can accept true bipolar input signals. On power-up, the analog inputs operate as eight single-ended analog input channels. If true differential or pseudo differential is required, a write to the control register is necessary after power-up to change this configuration. Figure 29 shows the equivalent analog input circuit of the AD7327 in single-ended mode. Figure 30 shows the equivalent analog input structure in differential mode. The two diodes provide ESD protection for the analog inputs. VDD D VIN0 C1 D VSS R1 C2 05401-023 B SW3 ADC CODE A SW1 A SW2 111...111 111...110 05401-020 VIN– COMPARATOR CS B VIN+ Figure 29. Equivalent Analog Input Circuit (Single-Ended) Rev. B | Page 17 of 36 AD7327 VDD C1 R1 C2 D 1.5 SCLK + t8 + tQUIET VSS to acquire the analog input signal. The ADC goes back into hold mode on the CS falling edge. C1 D VSS R1 C2 05401-024 D VIN– Figure 30. Equivalent Analog Input Circuit (Differential) Care should be taken to ensure that the analog input does not exceed the VDD and VSS supply rails by more than 300 mV. Exceeding this value causes the diodes to become forward biased and to start conducting into either the VDD supply rail or VSS supply rail. These diodes can conduct up to 10 mA without causing irreversible damage to the part. In Figure 29 and Figure 30, Capacitor C1 is typically 4 pF and can primarily be attributed to pin capacitance. Resistor R1 is a lumped component made up of the on resistance of the input multiplexer and the track-and-hold switch. Capacitor C2 is the sampling capacitor; its capacitance varies depending on the analog input range selected (see the Specifications section). As the VDD/VSS supply voltage is reduced, the on resistance of the input multiplexer increases. Therefore, based on the equation for tACQ, it is necessary to increase the amount of acquisition time provided to the AD7327, and, therefore, decrease the overall throughput rate. Figure 31 shows that as the VDD and VSS supplies are reduced, the specified THD performance degrades slightly. If the throughput rate is reduced when operating with the minimum VDD and VSS supplies, the specified THD performance is maintained. –75 VCC = VDRIVE = 5V INTERNAL REFERENCE TA = 25°C FIN = 10kHz ±5V RANGE SE MODE –80 THD (dB) VDD –85 –90 Track-and-Hold Section 500kSPS The track-and-hold on the analog input of the AD7327 allows the ADC to accurately convert an input sine wave of full-scale amplitude to 13-bit accuracy. The input bandwidth of the trackand-hold is greater than the Nyquist rate of the ADC. The AD7327 can handle frequencies up to 22 MHz. The track-and-hold enters its tracking mode on the 14th SCLK rising edge after the CS falling edge. The time required to acquire an input signal depends on how quickly the sampling capacitor is charged. With 0 source impedance, 305 ns is sufficient to acquire the signal to the 13-bit level. The acquisition time required is calculated using the following formula: tACQ = 10 × ((RSOURCE + R) × C) where C is the sampling capacitance, and R is the resistance seen by the track-and-hold amplifier looking back on the input. For the AD7327, the value of R includes the on resistance of the input multiplexer and is typically 300 Ω. RSOURCE should include any extra source impedance on the analog input. –95 5 7 9 11 13 15 17 19 ±VDD/VSS SUPPLIES (V) 05401-051 D VIN+ The AD7327 enters track on the 14th SCLK rising edge. When running the AD7327 at a throughput rate of 500 kSPS with a 10 MHz SCLK signal, the ADC has approximately Figure 31. THD vs. ±VDD/VSS Supply Voltage at 500 kSPS Unlike other bipolar ADCs, the AD7327 does not have a resistive analog input structure. On the AD7327, the bipolar analog signal is sampled directly onto the sampling capacitor. This gives the AD7327 high analog input impedance. An approximation for the analog input impedance can be calculated from the following formula: Z = 1/(fS × CS) where fS is the sampling frequency, and CS is the sampling capacitor value. CS depends on the analog input range chosen (see the Specifications section). When operating at 500 kSPS, the analog input impedance is typically 145 kΩ for the ±10 V range. As the sampling frequency is reduced, the analog input impedance further increases. As the analog input impedance increases, the current required to drive the analog input, therefore, decreases. Rev. B | Page 18 of 36 Data Sheet AD7327 V+ TYPICAL CONNECTION DIAGRAM Figure 32 shows a typical connection diagram for the AD7327. In this configuration, the AGND pin is connected to the analog ground plane of the system, and the DGND pin is connected to the digital ground plane of the system. The analog inputs on the AD7327 can be configured to operate in single-ended, true differential, or pseudo differential mode. The AD7327 can operate with either an internal or external reference. In Figure 32, the AD7327 is configured to operate with the internal 2.5 V reference. A 680 nF decoupling capacitor is required when operating with the internal reference. The VCC pin can be connected to either a 3 V supply voltage or a 5 V supply voltage. The VDD and VSS are the dual supplies for the high voltage analog input structures. The voltage on these pins must be equal to or greater than the highest analog input range selected on the analog input channels (see Table 6). The VDRIVE pin is connected to the supply voltage of the microprocessor. The voltage applied to the VDRIVE input controls the voltage of the serial interface. VDRIVE can be set to 3 V or 5 V. +15V 10µF VDD1 ANALOG INPUTS ±10V, ±5V, ±2.5V 0V TO +10V The AD7327 can have a total of four true differential analog input pairs. Differential signals have some benefits over singleended signals, including better noise immunity based on the common-mode rejection of the device and improvements in distortion performance. Figure 34 defines the configuration of the true differential analog inputs of the AD7327. VIN– 0.1µF 1ADDITIONAL PINS OMITTED FOR CLARITY. Figure 34. True Differential Inputs CS µC/µP SCLK DIN DGND SERIAL INTERFACE AGND 1MINIMUM VDD AND V SS SUPPLY VOLTAGES DEPEND ON THE HIGHEST ANALOG INPUT RANGE SELECTED. 05401-025 10µF 05401-026 True Differential Mode AD73271 DOUT VSS1 PINS OMITTED FOR CLARITY. Figure 33. Single-Ended Mode Typical Connection Diagram VIN+ –15V + 0.1µF V– 1ADDITIONAL AD7327 REFIN/OUT 680nF VSS +3V SUPPLY 10µF + VDD VCC AD73271 0.1µF VCC VDRIVE VIN0 VIN1 VIN2 VIN3 VIN4 VIN5 VIN6 VIN7 VIN+ VCC + 2.7V TO 5.25V + 10µF AGND 05401-027 + 0.1µF 5V The amplitude of the differential signal is the difference between the signals applied to the VIN+ and VIN− pins in each differential pair (VIN+ − VIN−). VIN+ and VIN− should be simultaneously driven by two signals each of amplitude ±4 × VREF (depending on the input range selected) that are 180° out of phase. Assuming the ±4 × VREF mode, the amplitude of the differential signal is −20 V to +20 V p-p (2 × 4 × VREF), regardless of the common mode. The common mode is the average of the two signals Figure 32. Typical Connection Diagram (VIN+ + VIN−)/2 ANALOG INPUT Single-Ended Inputs The AD7327 has a total of eight analog inputs when operating the AD7327 in single-ended mode. Each analog input can be independently programmed to one of the four analog input ranges. In applications where the signal source is high impedance, it is recommended to buffer the signal before applying it to the ADC analog inputs. Figure 33 shows the configuration of the AD7327 in single-ended mode. and is, therefore, the voltage on which the two input signals are centered. This voltage is set up externally, and its range varies with reference voltage. As the reference voltage increases, the common-mode range decreases. When driving the differential inputs with an amplifier, the actual common-mode range is determined by the output swing of the amplifier. If the differential inputs are not driven from an amplifier, the common-mode range is determined by the supply voltage on the VDD and the VSS supply pins. When a conversion takes place, the common mode is rejected, resulting in a noise-free signal of amplitude −2 × (4 × VREF) to +2 × (4 × VREF) corresponding to digital Code −4096 to Code +4095. Rev. B | Page 19 of 36 AD7327 8 5 ±5V RANGE 6 ±5V RANGE 3 ±2.5V RANGE VCOM RANGE (V) VCOM RANGE (V) 1 0 –2 –3 ±10V RANGE ±2.5V RANGE ±10V RANGE ±10V RANGE 2 0 –2 –4 ±5V RANGE –4 VCC = 3V VREF = 3V –6 05401-045 –5 –6 ±16.5V VDD/VSS ±12V VDD/VSS –8 ±12V VDD/VSS Figure 38. Common-Mode Range for VCC = 5 V and REFIN/OUT = 2.5 V 8 Pseudo Differential Inputs ±5V RANGE 6 VCOM RANGE (V) ±2.5V RANGE VCC = 5V VREF = 2.5V ±16.5V VDD/VSS Figure 35. Common-Mode Range for VCC = 3 V and REFIN/OUT = 3 V 4 ±5V RANGE ±2.5V RANGE 4 2 –1 ±10V RANGE 05401-048 4 ±5V RANGE The AD7327 can have four pseudo differential pairs or seven pseudo differential inputs referenced to a common VIN− pin. The VIN+ inputs are coupled to the signal source and must have an amplitude within the selected range for that channel as programmed in the range registers. A dc input is applied to the VIN− pin. The voltage applied to this input provides an offset for the VIN+ input from ground or a pseudo ground. Pseudo differential inputs separate the analog input signal ground from the ADC ground, allowing cancellation of dc common mode voltages. ±2.5V RANGE ±2.5V RANGE ±10V RANGE 2 ±10V RANGE 0 –2 05401-046 VCC = 5V VREF = 3V –4 ±16.5V VDD/VSS ±12V VDD/VSS When a conversion takes place, the pseudo ground corresponds to Code −4096 and the maximum amplitude corresponds to Code +4095. Figure 36. Common-Mode Range for VCC = 5 V and REFIN/OUT = 3 V 6 V+ 5V 4 ±5V RANGE ±5V RANGE VIN+ AD73271 0 VIN– –2 –4 VDD VCC ±10V RANGE ±10V ±2.5V RANGE RANGE VSS ±2.5V RANGE V– 1ADDITIONAL PINS OMITTED FOR CLARITY. VCC = 3V VREF = 2.5V –8 ±16.5V VDD/VSS ±12V VDD/VSS Figure 39. Pseudo Differential Inputs 05401-047 –6 05401-028 VCOM RANGE (V) 2 Figure 37. Common-Mode Range for VCC = 3 V and REFIN/OUT = 2.5 V Figure 40 and Figure 41 show the typical voltage range on the VIN− pin for the different analog input ranges when configured in the pseudo differential mode. For example, when the AD7327 is configured to operate in pseudo differential mode and the ±5 V range is selected, with ±16.5 V VDD/VSS supplies and 5 V VCC, the voltage on the VIN− pin can vary from −6.5 V to +6.5 V. Rev. B | Page 20 of 36 Data Sheet AD7327 6 4 ±5V RANGE ±2.5V RANGE ±10V RANGE The driver amplifier must be able to settle for a full-scale step to a 13-bit level, 0.0122%, in less than the specified acquisition time of the AD7327. An op amp such as the AD8021 meets this requirement when operating in single-ended mode. The AD8021 needs an external compensating NPO type of capacitor. The AD8022 can also be used in high frequency applications where a dual version is required. For lower frequency applications, op amps such as the AD797, AD845, and AD8610 can be used with the AD7327 in single-ended mode configuration. ±5V RANGE ±2.5V RANGE 2 0 –2 ±10V RANGE –4 –8 VCC = 5V VREF = 2.5V ±16.5V VDD/VSS Differential operation requires that VIN+ and VIN− be simultaneously driven with two signals of equal amplitude that are 180° out of phase. The common mode must be set up externally to the AD7327. The common-mode range is determined by the REFIN/ OUT voltage, the VCC supply voltage, and the particular amplifier used to drive the analog inputs. Differential mode with either an ac input or a dc input provides the best THD performance over a wide frequency range. Because not all applications have a signal preconditioned for differential operation, there is often a need to perform the single-ended-to-differential conversion. 0V TO +10V RANGE 0V TO +10V RANGE –6 ±12V VDD/VSS 05401-039 PSEUDO INPUT VOLTAGE RANGE (V) 8 Figure 40. Pseudo Input Range with VCC = 5 V 4 2 ±2.5V RANGE 0 This single-ended-to-differential conversion can be performed using an op amp pair. Typical connection diagrams for an op amp pair are shown in Figure 42 and Figure 43. In Figure 42, the common-mode signal is applied to the noninverting input of the second amplifier. –2 ±10V RANGE –4 ±10V RANGE ±2.5V RANGE 0V TO +10V RANGE –6 0V TO +10V RANGE VCC = 3V VREF = 2.5V –8 ±16.5V VDD/VSS ±12V VDD/VSS 1.5kΩ 05401-040 PSEUDO INPUT VOLTAGE RANGE (V) ±5V RANGE ±5V RANGE 3kΩ AD845 VIN V+ Figure 41. Pseudo Input Range with VCC = 3 V DRIVER AMPLIFIER CHOICE 1.5kΩ In applications where the harmonic distortion and signal-tonoise ratio are critical specifications, the analog input of the AD7327 should be driven from a low impedance source. Large source impedances significantly affect the ac performance of the ADC and can necessitate the use of an input buffer amplifier. 1.5kΩ V– 10kΩ VCOM 05401-029 AD845 20kΩ Figure 42. Single-Ended-to-Differential Configuration with the AD845 442Ω VIN 442Ω AD8021 V+ 442Ω 442Ω 442Ω Due to the programmable nature of the analog inputs on the AD7327, the choice of op amp used to drive the inputs is a function of the particular application and depends on the input configuration and the analog input voltage ranges selected. 442Ω V– AD8021 100Ω 05401-030 When no amplifier is used to drive the analog input, the source impedance should be limited to low values. The maximum source impedance depends on the amount of THD that can be tolerated in the application. The THD increases as the source impedance increases and performance degrades. Figure 21 and Figure 22 show graphs of the THD vs. the analog input frequency for various source impedances. Depending on the input range and analog input configuration selected, the AD7327 can handle source impedances of up to 5.5 kΩ before the THD starts to degrade. 1.5kΩ Figure 43. Single-Ended-to-Differential Configuration with the AD8021 Rev. B | Page 21 of 36 AD7327 REGISTERS The AD7327 has four programmable registers: the control register, sequence register, Range Register 1, and Range Register 2. These registers are write-only registers. ADDRESSING REGISTERS A serial transfer on the AD7327 consists of 16 SCLK cycles. The three MSBs on the DIN line during the 16 SCLK transfer are decoded to determine which register is addressed. The three MSBs consist of the write bit, the Register Select 1 bit, and the Register Select 2 bit. The register select bits are used to determine which of the four on-board registers is selected. The write bit determines if the data on the DIN line following the register select bits loads into the addressed register. If the write bit is 1, the bits load into the register addressed by the register select bits. If the write bit is 0, the data on the DIN line does not load into any register. Combinations of the write bit, the Register Select 1 bit, and the Register Select 2 bit other than those specified in Table 8 access registers for Analog Devices internal use only. Do not access these registers, as doing so may lead to unspecified operation of the device. Table 8. Decoding Register Select Bits and Write Bit Write 0 1 Register Select 1 0 0 Register Select 2 0 0 1 0 1 1 1 0 1 1 1 Description Data on the DIN line during this serial transfer is ignored. This combination selects the control register. The subsequent 12 bits are loaded into the control register. This combination selects Range Register 1. The subsequent 8 bits are loaded into Range Register 1. This combination selects Range Register 2. The subsequent 8 bits are loaded into Range Register 2. This combination selects the sequence register. The subsequent 8 bits are loaded into the sequence register. CONTROL REGISTER The control register is used to select the analog input channel, analog input configuration, reference, coding, and power mode. The control register is a write-only, 12-bit register. Data loaded on the DIN line corresponds to the AD7327 configuration for the next conversion. If the sequence register is being used, data should be loaded into the control register after the range registers and the sequence register have been initialized. The bit functions of the control register are shown in Table 9 (the power-up status of all bits is 0). MSB 15 Write 14 Register Select 1 13 Register Select 2 12 ADD2 11 ADD1 10 ADD0 9 Mode 1 8 Mode 0 7 PM1 6 PM0 5 Coding 4 Ref 3 Seq1 2 Seq2 1 ZERO LSB 0 0 Table 9. Control Register Details Bit 12, 11, 10 Mnemonic ADD2, ADD1, ADD0 9, 8 Mode 1, Mode 0 7, 6 5 PM1, PM0 Coding 4 Ref 3, 2 1 Seq1, Seq2 ZERO Description These three channel address bits are used to select the analog input channel for the next conversion if the sequencer is not being used. If the sequencer is being used, the three channel address bits are used to select the final channel in a consecutive sequence. These two mode bits are used to select the configuration of the eight analog input pins, VIN0 to VIN7. These pins are used in conjunction with the channel address bits. On the AD7327, the analog inputs can be configured as eight single-ended inputs, four fully differential inputs, four pseudo differential inputs, or seven pseudo differential inputs (see Table 10). The power management bits are used to select different power mode options on the AD7327 (see Table 11). This bit is used to select the type of output coding the AD7327 uses for the next conversion result. If coding = 0, the output coding is twos complement. If coding = 1, the output coding is straight binary. When operating in sequence mode, the output coding for each channel is the value written to the coding bit during the last write to the control register. The reference bit is used to enable or disable the internal reference. If Ref = 0, the external reference is enabled and used for the next conversion and the internal reference is disabled. If Ref = 1, the internal reference is used for the next conversion. When operating in sequence mode, the reference used for each channel is the value written to the Ref bit during the last write to the control register. The Sequence 1 and Sequence 2 bits are used to control the operation of the sequencer (see Table 12). A 0 should be written to this bit at all times. Rev. B | Page 22 of 36 Data Sheet AD7327 The eight analog input channels can be configured as seven pseudo differential analog inputs, four pseudo differential inputs, four true differential inputs, or eight single-ended analog inputs. Table 10. Analog Input Configuration Selection Channel Address Bits ADD2 ADD1 ADD0 0 0 0 0 0 1 0 1 0 0 1 1 1 0 0 1 0 1 1 1 0 1 1 1 Mode 1 = 1, Mode 0 = 1 7 Pseudo Differential Inputs VIN+ VIN− VIN0 VIN7 VIN1 VIN7 VIN2 VIN7 VIN3 VIN7 VIN4 VIN7 VIN5 VIN7 VIN6 VIN7 Temperature indicator Mode 1 = 1, Mode 0 = 0 4 Fully Differential Inputs VIN+ VIN− VIN0 VIN1 VIN0 VIN1 VIN2 VIN3 VIN2 VIN3 VIN4 VIN5 VIN4 VIN5 VIN6 VIN7 VIN6 VIN7 Mode 1 = 0, Mode 0 =1 4 Pseudo Differential Inputs VIN+ VIN− VIN0 VIN1 VIN0 VIN1 VIN2 VIN3 VIN2 VIN3 VIN4 VIN5 VIN4 VIN5 VIN6 VIN7 VIN6 VIN7 Mode 1 = 0, Mode 0 = 0 8 Single-Ended Inputs VIN+ VIN− VIN0 AGND VIN1 AGND VIN2 AGND VIN3 AGND VIN4 AGND VIN5 AGND VIN6 AGND VIN7 AGND Table 11. Power Mode Selection PM1 1 PM0 1 1 0 0 1 0 0 Description Full Shutdown Mode. In this mode, all internal circuitry on the AD7327 is powered down. Information in the control register is retained when the AD7327 is in full shutdown mode. Autoshutdown Mode. The AD7327 enters autoshutdown on the 15th SCLK rising edge when the control register is updated. All internal circuitry is powered down in autoshutdown. Autostandby Mode. In this mode, all internal circuitry is powered down, excluding the internal reference. The AD7327 enters autostandby mode on the 15th SCLK rising edge after the control register is updated. Normal Mode. All internal circuitry is powered up at all times. Table 12. Sequencer Selection Seq1 0 Seq2 0 0 1 1 0 1 1 Description The channel sequencer is not used. The analog input channel, selected by programming the ADD2 bit to ADD0 bit in the control register, selects the next channel for conversion. Uses the sequence of channels previously programmed into the sequence register for conversion. The AD7327 starts converting on the lowest channel in the sequence. The channels are converted in ascending order. If uninterrupted, the AD7327 keeps converting the sequence. The range for each channel defaults to the range previously written into the corresponding range register. Used in conjunction with the channel address bits in the control register. This allows continuous conversions on a consecutive sequence of channels, from Channel 0 up to and including a final channel selected by the channel address bits in the control register. The range for each channel defaults to the range previously written into the corresponding range register. The channel sequencer is not used. The analog channel, selected by programming the ADD2 bit to ADD0 bit in the control register, selects the next channel for conversion. SEQUENCE REGISTER The sequence register on the AD7327 is an 8-bit, write-only register. Each of the eight analog input channels has one corresponding bit in the sequence register. To select an analog input channel for inclusion in the sequence, set the corresponding channel bit to 1 in the sequence register. MSB 16 Write 15 Register Select 1 14 Register Select 2 13 VIN0 12 VIN1 11 VIN2 10 VIN3 Rev. B | Page 23 of 36 9 VIN4 8 VIN5 7 VIN6 6 VIN7 5 0 4 0 3 0 2 0 LSB 1 0 AD7327 RANGE REGISTERS The range registers are used to select one analog input range per analog input channel. Range Register 1 is used to set the ranges for Channel 0 to Channel 3. It is an 8-bit, write-only register with two dedicated range bits for each of the analog input channels from Channel 0 to Channel 3. There are four analog input ranges, ±10 V, ±5 V, ±2.5 V, and 0 V to +10 V. A write to Range Register 1 is selected by setting the write bit to 1 and the register select bits to 0 and 1. After the initial write to Range Register 1 occurs, each time an analog input is selected, the AD7327 automatically configures the analog input to the appropriate range, as indicated by Range Register 1. The ±10 V input range is selected by default on each analog input channel (see Table 13). MSB 16 Write 15 Register Select 1 14 Register Select 2 13 VIN0A 12 VIN0B 11 VIN1A 10 VIN1B 9 VIN2A 8 VIN2B 7 VIN3A 6 VIN3B 5 0 4 0 3 0 2 0 LSB 1 0 Range Register 2 is used to set the ranges for Channel 4 to Channel 7. It is an 8-bit, write-only register with two dedicated range bits for each of the analog input channels from Channel 4 to Channel 7. There are four analog input ranges, ±10 V, ±5 V, ±2.5 V, and 0 V to +10 V. After the initial write to Range Register 2 occurs, each time an analog input is selected, the AD7327 automatically configures the analog input to the appropriate range, as indicated by Range Register 2. The ±10 V input range is selected by default on each analog input channel (see Table 13). MSB 16 Write 15 Register Select 1 14 Register Select 2 13 VIN4A 12 VIN4B 11 VIN5A 10 VIN5B 9 VIN6A 8 VIN6B Table 13. Range Selection VINxA 0 0 1 1 VINxB 0 1 0 1 Description This combination selects the ±10 V input range on VINx. This combination selects the ±5 V input range on VINx. This combination selects the ±2.5 V input range on VINx. This combination selects the 0 V to +10 V input range on VINx. Rev. B | Page 24 of 36 7 VIN7A 6 VIN7B 5 0 4 0 3 0 2 0 LSB 1 0 Data Sheet AD7327 SEQUENCER OPERATION POWER ON. CS DIN: WRITE TO RANGE REGISTER 1 TO SELECT THE RANGE FOR EACH ANALOG INPUT CHANNEL. DOUT: CONVERSION RESULT FROM CHANNEL 0, ±10V RANGE, SINGLE-ENDED MODE. CS DIN: WRITE TO RANGE REGISTER 2 TO SELECT THE RANGE FOR EACH ANALOG INPUT CHANNEL. DOUT: CONVERSION RESULT FROM CHANNEL 0, SINGLE-ENDED MODE, RANGE SELECTED IN RANGE REGISTER 1. CS DIN: WRITE TO SEQUENCE REGISTER TO SELECT THE ANALOG INPUT CHANNELS TO BE INCLUDED IN THE SEQUENCE. DOUT: CONVERSION RESULT FROM CHANNEL 0, SINGLE-ENDED MODE, RANGE SELECTED IN RANGE REGISTER 1. CS DIN: WRITE TO CONTROL REGISTER TO START THE SEQUENCE, Seq1 = 0, Seq2 = 1. DOUT: CONVERSION RESULT FROM CHANNEL 0, SINGLE-ENDED MODE, RANGE SELECTED IN RANGE REGISTER 1. CS DIN: TIE DIN LOW/WRITE BIT = 0 TO CONTINUE TO CONVERT THROUGH THE SEQUENCE OF CHANNELS. CS DOUT: CONVERSION RESULT FROM FIRST CHANNEL IN THE SEQUENCE. DIN: WRITE TO CONTROL REGISTER TO STOP THE SEQUENCE, Seq1 = 0, Seq2 = 0. STOPPING A SEQUENCE. DOUT: CONVERSION RESULT FROM CHANNEL IN SEQUENCE. DIN TIED LOW/WRITE BIT = 0. CONTINUOUSLY CONVERT ON THE SELECTED SEQUENCE OF CHANNELS. SELECTING A NEW SEQUENCE. CS DIN: WRITE TO SEQUENCE REGISTER TO SELECT THE NEW SEQUENCE. 05401-031 DOUT: CONVERSION RESULT FROM CHANNEL X IN THE FIRST SEQUENCE. Figure 44. Programmable Sequence Flowchart The AD7327 can be configured to automatically cycle through a number of selected channels using the on-chip sequence register with the Seq1 bit and the Seq2 bit in the control register. Figure 44 shows how to program the AD7327 register to operate in sequence mode. After power-up, all of the four on-chip registers contain default values. Each analog input has a default input range of ±10 V. If different analog input ranges are required, a write to the range registers is required. This is shown in the first two serial transfers of Figure 44. These two initial serial transfers are only necessary if input ranges other than the default ranges are required. After the analog input ranges are configured, a write to the sequence register is necessary to select the channels to be included in the sequence. Once the channels for the sequence have been selected, the sequence can be initiated by writing to the control register and setting Seq1 to 0 and Seq2 to 1. The AD7327 continues to convert through the selected sequence without interruption, provided the sequence register remains unchanged and Seq1 = 0 and Seq2 = 1 in the control register. Rev. B | Page 25 of 36 AD7327 If a change to one of the range registers is required during a sequence, it is necessary to first stop the sequence by writing to the control register and setting Seq1 to 0 and Seq2 to 0. Next, the write to the range register should be completed to change the required range. The previously selected sequence should then be initiated again by writing to the control register and setting Seq1 to 0 and Seq2 to 1. The ADC converts the first channel in the sequence. The AD7327 can be configured to convert a sequence of consecutive channels (see Figure 45). This sequence begins by converting on Channel 0 and ends with a final channel as selected by Bit ADD2 to Bit ADD0 in the control register. In this configuration, there is no need for a write to the sequence register. To operate the AD7327 in this mode, set Seq1 to 1 and Seq2 to 0, and then select the final channel in the sequence by programming Bit ADD2 to Bit ADD0 in the control register. Once the control register is configured to operate the AD7327 in this mode, the DIN line can be held low or the write bit can be set to 0. To return to traditional multichannel operation, a write to the control register to set Seq1 to 0 and Seq2 to 0 is necessary. When Seq1 and Seq2 are both set to 0, or when both are set to 1, the AD7327 is configured to operate in traditional multichannel mode, where a write to the Channel Address Bit ADD2 to Bit ADD0 in the control register selects the next channel for conversion. POWER ON. CS DIN: WRITE TO RANGE REGISTER 1 TO SELECT THE RANGE FOR ANALOG INPUT CHANNELS. DOUT: CONVERSION RESULT FROM CHANNEL 0, ±10V RANGE, SINGLE-ENDED MODE. CS DIN: WRITE TO RANGE REGISTER 2 TO SELECT THE RANGE FOR ANALOG INPUT CHANNELS. DOUT: CONVERSION RESULT FROM CHANNEL 0, RANGE SELECTED IN RANGE REGISTER 1, SINGLE-ENDED MODE. CS DIN: WRITE TO CONTROL REGISTER TO SELECT THE FINAL CHANNEL IN THE CONSECUTIVE SEQUENCE, SET Seq1 = 1 AND Seq2 = 0. SELECT OUTPUT CODING FOR SEQUENCE. DOUT: CONVERSION RESULT FROM CHANNEL 0, RANGE SELECTED IN RANGE REGISTER 1, SINGLE-ENDED MODE. CS DIN: WRITE BIT = 0 OR DIN LINE HELD LOW TO CONTINUE TO CONVERT THROUGH THE SEQUENCE OF CONSECUTIVE CHANNELS. DOUT: CONVERSION RESULT FROM CHANNEL 0, RANGE SELECTED IN RANGE REGISTER 1. CS DIN: WRITE BIT = 0 OR DIN LINE HELD LOW TO CONTINUE THROUGH SEQUENCE OF CONSECUTIVE CHANNELS. DOUT: CONVERSION RESULT FROM CHANNEL 1, RANGE SELECTED IN RANGE REGISTER 1. STOPPING A SEQUENCE. DIN TIED LOW/WRITE BIT = 0. CONTINUOUSLY CONVERT ON CONSECUTIVE SEQUENCE OF CHANNELS. CS DOUT: CONVERSION RESULT FROM CHANNEL IN SEQUENCE. Figure 45. Flowchart for Consecutive Sequence of Channels Rev. B | Page 26 of 36 05401-032 DIN: WRITE TO CONTROL REGISTER TO STOP THE SEQUENCE, Seq1 = 0, Seq2 = 0. Data Sheet AD7327 REFERENCE TEMPERATURE INDICATOR The AD7327 can operate with either the internal 2.5 V onchip reference or an externally applied reference. The internal reference is selected by setting the Ref bit in the control register to 1. On power-up, the Ref bit is 0, which selects the external reference for the AD7327 conversion. Suitable reference sources for the AD7327 include AD780, AD1582, ADR431, REF193, and ADR391. The AD7327 has an on-chip temperature indicator. The temperature indicator can be used to give local temperature measurements on the AD7327. To access the temperature indicator, the ADC should be configured in pseudo differential mode, Mode 1 = Mode 0 = 1, and channel Bit ADD2, Bit ADD1, and Bit ADD0 should be set to 1. VIN7 must be tied to AGND or to a small dc voltage within the specified pseudo input range for the selected analog input range. When a conversion is initiated in this configuration, the output code represents the temperature (see Figure 46 and Figure 47). When using the temperature indicator on the AD7327, the part should be operated at low throughput rates, such as approximately 50 kSPS for the ±10 V range and 30 kSPS for the ±2.5 V range. The throughput rate is reduced for the temperature indicator mode because the AD7327 requires more acquisition time for this mode. The AD7327 is specified for a 2.5 V to 3 V reference range. When a 3 V reference is selected, the ranges are ±12 V, ±6 V, ±3 V, and 0 V to +12 V. For these ranges, the VDD and VSS supply must be equal to or greater than the maximum analog input range selected (see Table 6). 4420 VCC = VDRIVE = 5V VDD/VSS = ±12V 50kSPS 4410 4400 ±10V RANGE, INT REF 4390 4380 4370 4360 4350 VDRIVE 4340 –40 The AD7327 has a VDRIVE feature to control the voltage at which the serial interface operates. VDRIVE allows the ADC to easily interface to both 3 V and 5 V processors. For example, if the AD7327 is operated with a VCC of 5 V, the VDRIVE pin can be powered from a 3 V supply. This allows the AD7327 to accept large bipolar input signals with low voltage digital processing. –20 0 20 40 60 80 100 TEMPERATURE (°C) 05401-033 On power-up, if the internal reference operation is required for the ADC conversion, a write to the control register is necessary to set the Ref bit to 1. During the control register write, the conversion result from the first initial conversion is invalid. The reference buffer requires 500 μs to power up and charge the 680 nF decoupling capacitor during the power-up time. ADC OUTPUT CODE The internal reference circuitry consists of a 2.5 V band gap reference and a reference buffer. When operating the AD7327 in internal reference mode, the 2.5 V internal reference is available at the REFIN/OUT pin, which should be decoupled to AGND using a 680 nF capacitor. It is recommended that the internal reference be buffered before applying it elsewhere in the system. The internal reference is capable of sourcing up to 90 μA. Figure 46. Temperature vs. ADC Output Code for ±10 V Range 5450 VCC = VDRIVE = 5V VDD/VSS = ±12V ±2.5V RANGE INT REFERENCE 30kSPS ADC OUTPUT CODE 5400 5350 5300 5250 5200 5100 –40 –20 0 20 40 60 80 TEMPERATURE (°C) Figure 47. Temperature vs. ADC Output Code for ±2.5 V Range Rev. B | Page 27 of 36 05401-034 5150 AD7327 MODES OF OPERATION The AD7327 remains fully powered up at the end of the conversion if both PM1 and PM0 contain 0 in the control register. The AD7327 has several modes of operation that are designed to provide flexible power management options. These options can be chosen to optimize the power dissipation/throughput rate ratio for different application requirements. The mode of operation of the AD7327 is controlled by the power management bits, Bit PM1 and Bit PM0, in the control register as shown in Table 11. The default mode is normal mode, where all internal circuitry is fully powered up. To complete the conversion and access the conversion result, 16 serial clock cycles are required. At the end of the conversion, CS can idle either high or low until the next conversion. Once the data transfer is complete, another conversion can be initiated after the quiet time, tQUIET, has elapsed. NORMAL MODE FULL SHUTDOWN MODE (PM1 = PM0 = 0) (PM1 = PM0 = 1) This mode is intended for the fastest throughput rate performance with the AD7327 being fully powered up at all times. Figure 48 shows the general operation of the AD7327 in normal mode. In this mode, all internal circuitry on the AD7327 is powered down. The part retains information in the registers during full shutdown. The AD7327 remains in full shutdown mode until the power management bits, Bit PM1 and Bit PM0, in the control register are changed. The conversion is initiated on the falling edge of CS, and the track-and-hold section enters hold mode, as described in the Serial Interface section. Data on the DIN line during the 16 SCLK transfer is loaded into one of the on-chip registers if the write bit is set. The register is selected by programming the register select bits (see Table 8). A write to the control register with PM1 = 1 and PM0 = 1 places the part into full shutdown mode. The AD7327 enters full shutdown mode on the 15th SCLK rising edge once the control register is updated. CS 1 If a write to the control register occurs while the part is in full shutdown mode with the power management bits, Bit PM1 and Bit PM0, set to 0 (normal mode), the part begins to power up on the 15th SCLK rising edge once the control register is updated. Figure 49 shows how the AD7327 is configured to exit full shutdown mode. To ensure the AD7327 is fully powered up, tPOWER-UP should elapse before the next CS falling edge. 16 SCLK DOUT 05401-035 3 CHANNEL I.D. BITS, SIGN BIT + CONVERSION RESULT DATA INTO CONTROL/SEQUENCE/RANGE1/RANGE2 REGISTER DIN Figure 48. Normal Mode PART IS IN FULL SHUTDOWN THE PART IS FULLY POWERED UP ONCE tPOWER-UP HAS ELAPSED PART BEGINS TO POWER UP ON THE 15TH SCLK RISING EDGE AS PM1 = PM0 = 0 tPOWER-UP CS 1 16 1 16 SDATA DIN INVALID DATA CHANNEL IDENTIFIER BITS + CONVERSION RESULT DATA INTO CONTROL REGISTER DATA INTO CONTROL REGISTER CONTROL REGISTER IS LOADED ON THE FIRST 15 CLOCKS, PM1 = 0, PM0 = 0 TO KEEP THE PART IN NORMAL MODE, LOAD PM1 = PM0 = 0 IN CONTROL REGISTER Figure 49. Exiting Full Shutdown Mode Rev. B | Page 28 of 36 05401-041 SCLK Data Sheet AD7327 AUTOSHUTDOWN MODE (PM1 = 1, PM0 = 0) Once the autoshutdown mode is selected, the AD7327 automatically enters shutdown on the 15th SCLK rising edge. In autoshutdown mode, all internal circuitry is powered down. The AD7327 retains information in the registers during autoshutdown. The track-and-hold is in hold mode during autoshutdown. On the rising CS edge, the track-and-hold, which was in hold during autoshutdown, returns to track as the AD7327 begins to power up. The power-up from autoshutdown is 500 µs. When the control register is programmed to transition to autoshutdown mode, it does so on the 15th SCLK rising edge. Figure 50 shows the part entering autoshutdown mode. The AD7327 automatically begins to power up on the CS rising edge. The tPOWER-UP is required before a valid conversion, initiated by bringing the CS signal low, can take place. Once this valid conversion is complete, the AD7327 powers down again on the 15th SCLK rising edge. The CS signal must remain low again to keep the part in autoshutdown mode. As is the case with autoshutdown mode, the AD7327 enters standby on the 15th SCLK rising edge once the control register is updated (see Figure 50). The part retains information in the registers during standby. The AD7327 remains in standby until it receives a CS rising edge. The ADC begins to power up on the CS rising edge. On the CS rising edge, the track-and-hold, which was in hold mode while the part was in standby, returns to track. The power-up time from standby is 700 ns. The user should ensure that 700 ns have elapsed before bringing CS low to attempt a valid conversion. Once this valid conversion is complete, the AD7327 again returns to standby on the 15th SCLK rising edge. The CS signal must remain low to keep the part in standby mode. Figure 50 shows the part entering autoshutdown mode. The sequence of events is the same when entering autostandby mode. In Figure 50, the power management bits are configured for autoshutdown. For autostandby mode, the power management bits, PM1 and PM0, should be set to 0 and 1, respectively. AUTOSTANDBY MODE (PM1 = 0, PM0 =1) In autostandby mode, portions of the AD7327 are powered down, but the on-chip reference remains powered up. The reference bit in the control register should be 1 to ensure that the on-chip reference is enabled. This mode is similar to autoshutdown but allows the AD7327 to power up much faster, which allows faster throughput rates. PART BEGINS TO POWER UP ON CS RISING EDGE PART ENTERS SHUTDOWN MODE ON THE 15TH RISING SCLK EDGE AS PM1 = 1, PM0 = 0 CS 1 THE PART IS FULLY POWERED UP ONCE tPOWER-UP HAS ELAPSED tPOWER-UP 15 16 1 15 16 SCLK DIN VALID DATA VALID DATA DATA INTO CONTROL REGISTER DATA INTO CONTROL REGISTER 05401-042 SDATA CONTROL REGISTER IS LOADED ON THE FIRST 15 CLOCKS, PM1 = 1, PM0 = 0 Figure 50. Entering Autoshutdown/Autostandby Mode Rev. B | Page 29 of 36 AD7327 POWER VS. THROUGHPUT RATE 20 16 8 6 VARIABLE SCLK 4 2 100 200 300 400 THROUGHPUT RATE (kSPS) Figure 52. Power vs. Throughput Rate with 5 V VCC 6 VARIABLE SCLK 4 2 0 300 400 THROUGHPUT RATE (kSPS) 500 05401-052 AVERAGE POWER (mW) 10 0 8 200 12 0 VCC = 3V VDD/VSS = ±12V TA = 25°C 10 INTERNAL REFERENCE 100 14 Figure 51. Power vs. Throughput Rate with 3 V VCC Rev. B | Page 30 of 36 500 05401-053 12 0 VCC = 5V VDD/VSS = ±12V TA = 25°C INTERNAL REFERENCE 18 AVERAGE POWER (mW) The power consumption of the AD7327 varies with throughput rate. The static power consumed by the AD7327 is very low, and significant power savings can be achieved as the throughput rate is reduced. Figure 51 and Figure 52 shows the power vs. throughput rate for the AD7327 at a VCC of 3 V and 5 V, respectively. Both plots clearly show that the average power consumed by the AD7327 is greatly reduced as the sample frequency is reduced. This is true whether a fixed SCLK value is used or if it is scaled with the sampling frequency. Figure 51 and Figure 52 show the power consumption when operating in normal mode for a variable SCLK that scales with the sampling frequency. Data Sheet AD7327 SERIAL INTERFACE Figure 53 shows the timing diagram for the serial interface of the AD7327. The serial clock applied to the SCLK pin provides the conversion clock and controls the transfer of information to and from the AD7327 during a conversion. Data is clocked into the AD7327 on the SCLK falling edge. The three MSBs on the DIN line are decoded to select which register is addressed. The control register is a 12-bit register. If the control register is addressed by the three MSBs, the data on the DIN line is loaded into the control on the 15th SCLK falling edge. If the sequence register or either of the range registers is addressed, the data on the DIN line is loaded into the addressed register on the 11th SCLK falling edge. The CS signal initiates the data transfer and the conversion process. The falling edge of CS puts the track-and-hold into hold mode and takes the bus out of three-state. Then the analog input signal is sampled. Once the conversion is initiated, it requires 16 SCLK cycles to complete. Conversion data is clocked out of the AD7327 on each SCLK falling edge. Data on the DOUT line consists of three channel identifier bits, a sign bit, and a 12-bit conversion result. The channel identifier bits are used to indicate which channel corresponds to the conversion result. The ADD2 bit is clocked out on the CS falling edge, and the ADD1 bit is clocked out on the first SCLK falling edge. The track-and-hold goes back into track mode on the 14 SCLK rising edge. On the 16th SCLK falling edge, the DOUT line returns to three-state. If the rising edge of CS occurs before 16 SCLK cycles have elapsed, the conversion is terminated, and the DOUT line returns to three-state. Depending on where the CS signal is brought high, the addressed register may be updated. th t1 CS tCONVERT t2 1 2 3 4 3 IDENTIFICATION BITS t3 ADD1 DOUT THREE- ADD2 t9 STATE DIN WRITE REG SEL1 ADD0 SIGN 5 t4 13 14 DB11 15 16 t5 t7 DB10 DB2 t8 DB1 t10 REG SEL2 tQUIET DB0 THREE-STATE MSB LSB DON’T CARE Figure 53. Serial Interface Timing Diagram (Control Register Write) Rev. B | Page 31 of 36 05401-036 SCLK t6 AD7327 MICROPROCESSOR INTERFACING The serial interface on the AD7327 allows the part to be directly connected to a range of different microprocessors. This section explains how to interface the AD7327 with some common microcontroller and DSP serial interface protocols. AD7327 TO ADSP-21xx The ADSP-21xx family of DSPs interface directly to the AD7327 without requiring glue logic. The VDRIVE pin of the AD7327 takes the same supply voltage as that of the ADSP-21xx. This allows the ADC to operate at a higher supply voltage than its serial interface. The SPORT0 on the ADSP-21xx should be configured as shown in Table 14. Table 14. SPORT0 Control Register Setup Description Alternative framing Active low frame signal Right justify data 16-bit data-word Internal serial clock Frame every word For example, the ADSP-2111 has a master clock frequency of 16 MHz. If the SCLKDIV register is loaded with the value 3, an SCLK of 2 MHz is obtained, and eight master clock periods elapse for every one SCLK period. If the timer registers are loaded with the value 803, 100.5 SCLKs occur between interrupts and, subsequently, between transmit instructions. This situation leads to nonequidistant sampling because the transmit instruction occurs on an SCLK edge. If the number of SCLKs between interrupts is an integer of N, equidistant sampling is implemented by the DSP. AD7327 TO ADSP-BF53x The connection diagram is shown in Figure 54. The ADSP-21xx has TFS0 and RFS0 tied together. TFS0 is set as an output, and RFS0 is set as an input. The DSP operates in alternative framing mode, and the SPORT0 control register is set up as described in Table 14. The frame synchronization signal generated on the TFS is tied to CS, and, as with all signal processing applications, requires equidistant sampling. However, as in this example, the timer interrupt is used to control the sampling rate of the ADC, and under certain conditions, equidistant sampling cannot be achieved. The ADSP-BF53x family of DSPs interfaces directly to the AD7327 without requiring glue logic, as shown in Figure 55. The SPORT0 Receive Configuration 1 register should be set up as outlined in Table 15. ADSP-BF53x1 AD73271 SCLK CS RFS0 DIN DT0 DOUT DR0 VDRIVE ADSP-21xx1 AD73271 SCLK VDD 1ADDITIONAL PINS OMITTED FOR CLARITY. SCLK0 CS TFS0 RFS0 DIN DT0 DOUT DR0 RSCLK0 05401-038 Setting TFSW = RFSW = 1 INVRFS = INVTFS = 1 DTYPE = 00 SLEN = 1111 ISCLK = 1 TFSR = RFSR = 1 IRFS = 0 ITFS = 1 The frequency of the serial clock is set in the SCLKDIV register. When the instruction to transmit with TFS is given (AX0 = TX0), the state of the serial clock is checked. The DSP waits until the SCLK has gone high, low, and high again before starting the transmission. If the timer and SCLK are chosen so that the instruction to transmit occurs on or near the rising edge of SCLK, data can be transmitted immediately or at the next clock edge. Figure 55. Interfacing the AD7327 to the ADSP-BF53x Table 15. SPORT0 Receive Configuration 1 Register VDD 1ADDITIONAL PINS OMITTED FOR CLARITY. 05401-037 VDRIVE Figure 54. Interfacing the AD7327 to the ADSP-21xx The timer registers are loaded with a value that provides an interrupt at the required sampling interval. When an interrupt is received, a value is transmitted with TFS/DT (ADC control word). The TFS is used to control the RFS, and hence the reading of data. Setting RCKFE = 1 LRFS = 1 RFSR = 1 IRFS = 1 RLSBIT = 0 RDTYPE = 00 IRCLK = 1 RSPEN = 1 SLEN = 1111 TFSR = RFSR = 1 Rev. B | Page 32 of 36 Description Sample data with falling edge of RSCLK Active low frame signal Frame every word Internal RFS used Receive MSB first Zero fill Internal receive clock Receive enable 16-bit data-word Data Sheet AD7327 APPLICATION HINTS LAYOUT AND GROUNDING POWER SUPPLY CONFIGURATION The printed circuit board that houses the AD7327 should be designed so that the analog and digital sections are confined to certain areas of the board. This design facilitates the use of ground planes that can easily be separated. It is recommended that Schottky diodes be placed in series with the AD7327 VDD and VSS supply signals. Figure 56 shows this Schottky diode configuration. BAT43 Schottky diodes are used. V+ 3V/5V To provide optimum shielding for ground planes, a minimum etch technique is generally best. All AGND pins on the AD7327 should be connected to the AGND plane. Digital and analog ground pins should be joined in only one place. If the AD7327 is in a system where multiple devices require an AGND and DGND connection, the connection should still be made at only one point. A star point should be established as close as possible to the ground pins on the AD7327. VDD VIN0 To avoid radiating noise to other sections of the board, components, such as clocks, with fast switching signals should be shielded with digital ground and never run near the analog inputs. Avoid crossover of digital and analog signals. To reduce the effects of feedthrough within the board, traces should be run at right angles to each other. A microstrip technique is the best method, but its use may not be possible with a double-sided board. In this technique, the component side of the board is dedicated to ground planes, and signals are placed on the other side. Good decoupling is also important. All analog supplies should be decoupled with 10 µF tantalum capacitors in parallel with 0.1 µF capacitors to AGND. To achieve the best results from these decoupling components, they must be placed as close as possible to the device, ideally right up against the device. The 0.1 µF capacitors should have a low effective series resistance (ESR) and low effective series inductance (ESI), such as is typical of common ceramic and surface mount types of capacitors. These low ESR, low ESI capacitors provide a low impedance path to ground at high frequencies to handle transient currents due to internal logic switching. CS VIN1 VIN2 SCLK VIN3 DOUT VIN4 VIN5 DIN VIN6 VIN7 VSS V– 1ADDITIONAL PINS OMITTED FOR CLARITY. 05401-056 Good connections should be made to the power and ground planes. This can be done with a single via or multiple vias for each supply and ground pin. Avoid running digital lines under the AD7327 device because this couples noise onto the die. However, the analog ground plane should be allowed to run under the AD7327 to avoid noise coupling. The power supply lines to the AD7327 device should use as large a trace as possible to provide low impedance paths and reduce the effects of glitches on the power supply line. VCC AD73271 Figure 56. Schottky Diode Connection In an application where non-symmetrical VDD and VSS supplies are being used, adhere to the following guidelines. Table 16 outlines the VSS supply range that can be used for particular VDD voltages when non-symmetrical supplies are required. When operating the AD7327 with low VDD and VSS voltages, it is recommended that these supplies be symmetrical. Table 16. Non-Symmetrical VDD and VSS Requirements VDD 5V 6V 7V 8V 9V 10 V to 16.5 V Typical VSS Range −5 V to −5.5 V −5 V to −8.5 V −5 V to −11.5 V −5 V to −15 V −5 V to −16.5 V −5 V to −16.5 V For the 0 to 4 × VREF range, VSS can be tied to AGND as per minimum supply recommendations outlined in Table 6. Rev. B | Page 33 of 36 AD7327 OUTLINE DIMENSIONS 6.60 6.50 6.40 20 11 4.50 4.40 4.30 6.40 BSC 10 1 PIN 1 0.65 BSC 1.20 MAX 0.15 0.05 COPLANARITY 0.10 0.30 0.19 0.20 0.09 8° 0° SEATING PLANE 0.75 0.60 0.45 COMPLIANT TO JEDEC STANDARDS MO-153-AC Figure 57. 20-Lead Thin Shrink Small Outline Package [TSSOP] (RU-20) Dimensions show in millimeters ORDERING GUIDE Model 1 AD7327BRUZ AD7327BRUZ-REEL AD7327BRUZ-REEL7 EVAL-AD7327SDZ EVAL-SDP-CB1Z 1 Temperature Range −40°C to +85°C −40°C to +85°C −40°C to +85°C Package Description 20-Lead TSSOP 20-Lead TSSOP 20-Lead TSSOP Evaluation Board Controller Board Z = RoHS Compliant Part. Rev. B | Page 34 of 36 Package Option RU-20 RU-20 RU-20 Data Sheet AD7327 NOTES Rev. B | Page 35 of 36 AD7327 Data Sheet NOTES ©2006–2013 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D05401-0-12/13(B) Rev. B | Page 36 of 36