ILPA40JUD SERIES 40W Dimmable Water-Proof Constant Current LED Driver – – – – – – – 2 Year Warranty Wide Input Voltage 90 to 305VAC, 47 to 63Hz Constant Output Current Available From 350mA To 3330mA Over Voltage, Short Circuit, Over Load Protection High Efficiency (up to 88%) Active Power Factor Correction (PFC) (92% typical) IP66 Waterproof Rating Comply with UL8750 & EN61347 Safety Regulation (Pending) Approvals: (Pending) Single Output Part Number ILPA40JUD-S333DS ILPA40JUD-S222DS ILPA40JUD-S166DS ILPA40JUD-S140DS ILPA40JUD-S128DS ILPA40JUD-S105DS ILPA40JUD-S070DS ILPA40JUD-S045DS ILPA40JUD-S035DS Output Current Range (Min. / Typ. / Max.) 3164 / 3330 / 3497 mA 2109 / 2220 / 2331 mA 1577 / 1660 / 1743 mA 1330 / 1400 / 1470 mA 1216 / 1280 / 1344 mA 998 / 1050 / 1103 mA 665 / 700 / 735 mA 428 / 450 / 473 mA 333 / 350 / 368 mA Output Voltage (Min. / Max.) 4 / 12 VDC 6 / 18 VDC 8 / 24 VDC 10 / 29 VDC 11 / 31 VDC 12 / 36 VDC 18 / 54 VDC 30 / 89 VDC 38 / 114 VDC Efficiency (220VAC, Full Load) 84% 85% 86% 87% 87% 87% 87% 88% 88% Over Voltage Protection (Min. / Typ. / Max.) 13 / 15 / 17 VDC 22 / 24 / 26 VDC 30 / 32 / 34 VDC 36 / 38 / 40 VDC 41 / 43 / 45 VDC 46 / 48 / 50 VDC 68 / 70 / 72 VDC 114 / 116 / 118 VDC 146 / 148 / 150 VDC Max. Output Power 35W 36W 38W 36W 38W 38W 38W 40W 40W Electrical Characteristics Parameter Input Voltage Input Frequency Output Power Range Input Current (Low Line) Input Current (High Line) High Line Inrush Current Power Factor Correction Efficiency No Load Power Dissipation Line Regulation Load Regulation Over Voltage Protection Over Load Protection Short Circuit Protection Output Overshoot / Undershoot Start Up Time Ripple & Noise (Peak to Peak) Test Conditions Operating Voltage Vin=90 to 305VAC Io=Full load, Vin=115VAC Io=Full load, Vin=230VAC Io=Full load, 25°C, Cool start, Vin=230VAC Vin=110VAC Min. 90 47 0 Typ. Max. 305 63 40 0.48 0.23 20 99 Unit VAC Hz W A A A % Io=Full Load, Vin=220VAC 88 % 3 W Io=Full Load 2 % Vin=230VAC 5 % Latch mode. The power unit shall return to normal operation only after the power is turn-on again. (Please refer to output table.) Hiccup mode. The power supply shall be self-recovery 1.25 Po when the fault condition is removed. No damage shall occur when any output operating in a short circuit condition. The power supply shall be self-recovery when the fault condition is removed. When power on or off 10 % Io=Full Load, Vin=100VAC 1.7 2 S Measured by 20 MHz bandwidth oscilloscope and the output paralleled a 0.1 uF ceramic capacitor and a 10 uF electrolytic capacitor. 5 % Vo Conditions Parameter Test Conditions Min. Operating Temperature Humidity: 10% RH to 100% RH Storage Temperature Humidity: 5% RH to 100% RH MTBF: Operation temperature at 25°C, calculated per MIL-HDBK-217F Life Time at 25°C ambient temperature Typ. -20 -40 0.487M 0.077M Max. Unit 70 85 °C °C Hours Hours Approvals and Compliance Parameter EMI EMS Safety UL/c-UL, CE Waterproof Standards EN55015 EN61000-3-2, EN61000-3-3, EN61000-4-2, EN61000-4-3, , EN61000-4-4, , EN61000-4-5, EN61000-4-6, EN61000-4-8, EN61000-4-11, EN61547 (Pending) UL8750 Compliant to UL1310 ClaST 2, UL1012, UL935, CSA-C22.2 No. 0, CSA-C22.2 No. 107.1, CSA-C22.2 No.250.0, EN61347-1,EN61347-2-13 IP66 Rating Mechanical Parameter Specification Dimension, 78x80x25mm (3.07x3.15x0.98 inches) Net Weight 200g approx. Dimming Control Parameter Min. Typ. Max. Unit 10V Output Voltage 9.8 10V 10.2 VDC 10V Output Source Current -10 2 mA Absolute Max. Voltage on the 1~10V Input Pin -2 15 VDC Source Current on 0-10V Input Pin 0 1 mA The dimmer control may be operated from either a potentiometer or from an input signal of 0 ~ 10 Vdc. Two recommended implementations are provided above Notes: 1. For the driver to operate properly, the load voltage must be maintained above the minimum voltage threshold (approx. 33% of t he max. output voltage for any given model). 2. If the output voltage is maintained above 50% of the maximum output voltage, the dimmer control may be operated over the entire 0-10V range with output current varying from 100% down to practically 0%. 3. If the output voltage is maintained between 33-50% of the maximum output voltage, the dimmer control may be operated over 5-10V range with output current