MC10H100 Quad 2−Input NOR Gate With Strobe Description The MC10H100 is a quad NOR gate. Each gate has 3 inputs, two of which are independent and one of which is tied common to all four gates. http://onsemi.com MARKING DIAGRAMS* Features • Propagation Delay, 1.0 ns Typical • 25 mW Typ/Gate (No Load) • Improved Noise Margin 150 mV (Over Operating Voltage and • • • 16 Temperature Range) Voltage Compensated MECL 10K™ Compatible Pb−Free Packages are Available* MC10H100L AWLYYWW CDIP−16 L SUFFIX CASE 620 1 16 MC10H100P AWLYYWWG 16 1 PDIP−16 P SUFFIX CASE 648 1 10H100 ALYWG SOEIAJ−16 CASE 966 A WL, L YY, Y WW, W G = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free Package (Note: Microdot may be in either location) *For additional marking information, refer to Application Note AND8002/D. ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 3 of this data sheet. *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. © Semiconductor Components Industries, LLC, 2006 February, 2006 − Rev. 7 1 Publication Order Number: MC10H100/D MC10H100 4 2 5 6 3 7 9 10 11 14 12 15 13 2=4+5+9 VCC1 = Pin 1 VCC2 = Pin 16 VEE = Pin 8 VCC1 1 16 VCC2 Aout 2 15 Dout Bout 3 14 Cout Ain 4 13 Din Ain 5 12 Din Bin 6 11 Cin Bin 7 10 Cin VEE 8 9 Common Input (A, B, C, D) Pin assignment is for Dual−in−Line Package. Figure 2. Pin Assignment Figure 1. Logic Diagram Table 1. MAXIMUM RATINGS Symbol Rating Unit VEE Power Supply (VCC = 0) Characteristic −8.0 to 0 Vdc VI Input Voltage (VCC = 0) 0 to VEE Vdc Iout Output Current 50 100 mA TA Operating Temperature Range 0 to +75 °C Tstg Storage Temperature Range −55 to +150 −55 to +165 °C Continuous Surge Plastic Ceramic Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. Table 2. ELECTRICAL CHARACTERISTICS (VEE = −5.2 V ±5%) (Note 1) 0° Symbol Characteristic Min 25° Max Min − 29 − − 900 500 0.5 75° Max Min Max Unit − 26 − − 560 310 − 29 mA − − 560 310 mA − 0.5 − 0.3 − mA IE Power Supply Current IinH Input Current High IinL Input Current Low VOH High Output Voltage −1.02 −0.84 −0.98 −0.81 −0.92 −0.735 Vdc VOL Low Output Voltage −1.95 −1.63 −1.95 −1.63 −1.95 −1.60 Vdc VIH High Input Voltage −1.17 −0.84 −1.13 −0.81 −1.07 −0.735 Vdc VIL Low Input Voltage −1.95 −1.48 −1.95 −1.48 −1.95 −1.45 Vdc Pin 9 All Other Inputs 1. Each MECL 10H™ series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 Ifpm is maintained. Outputs are terminated through a 50 W resistor to −2.0 V. http://onsemi.com 2 MC10H100 Table 3. AC CHARACTERISTICS 0° Symbol Characteristic Pin 9 Only Exclude Pin 9 25° 75° Min Max Min Max Min Max Unit 0.65 0.4 1.6 1.3 0.7 0.45 1.7 1.35 0.7 0.5 1.8 1.5 ns tpd Propagation Delay tr Rise Time 0.5 2.0 0.5 2.1 0.5 2.2 ns tf Fall Time 0.5 2.0 0.5 2.1 0.5 2.2 ns NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. ORDERING INFORMATION Package Shipping† MC10H100M SOEIAJ−16 50 Unit / Rail MC10H100MG SOEIAJ−16 (Pb−Free) 50 Unit / Rail MC10H100MEL SOEIAJ−16 2000 / Tape & Reel MC10H100MELG SOEIAJ−16 (Pb−Free) 2000 / Tape & Reel MC10H100L CDIP−16 25 Unit / Rail MC10H100P PDIP−16 25 Unit / Rail MC10H100PG PDIP−16 (Pb−Free) 25 Unit / Rail Device †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 3 MC10H100 PACKAGE DIMENSIONS SOEIAJ−16 CASE 966−01 ISSUE A 16 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS AND ARE MEASURED AT THE PARTING LINE. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 5. THE LEAD WIDTH DIMENSION (b) DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE LEAD WIDTH DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSIONS AND ADJACENT LEAD TO BE 0.46 ( 0.018). LE 9 Q1 E HE 1 M_ L 8 Z DETAIL P D e VIEW P A DIM A A1 b c D E e HE L LE M Q1 Z A1 b 0.13 (0.005) c 0.10 (0.004) M 16 9 1 8 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIMENSION F MAY NARROW TO 0.76 (0.030) WHERE THE LEAD ENTERS THE CERAMIC BODY. −B− C −T− L K N SEATING PLANE M E J G D INCHES MIN MAX −−− 0.081 0.002 0.008 0.014 0.020 0.007 0.011 0.390 0.413 0.201 0.215 0.050 BSC 0.291 0.323 0.020 0.033 0.043 0.059 10 _ 0_ 0.028 0.035 −−− 0.031 CDIP−16 L SUFFIX CERAMIC DIP PACKAGE CASE 620−10 ISSUE T −A− F MILLIMETERS MIN MAX −−− 2.05 0.05 0.20 0.35 0.50 0.10 0.20 9.90 10.50 5.10 5.45 1.27 BSC 7.40 8.20 0.50 0.85 1.10 1.50 10 _ 0_ 0.70 0.90 −−− 0.78 0.25 (0.010) 16 PL 0.25 (0.010) 16 PL M T A S http://onsemi.com 4 M T B S DIM A B C D E F G H K L M N INCHES MIN MAX 0.750 0.785 0.240 0.295 −−− 0.200 0.015 0.020 0.050 BSC 0.055 0.065 0.100 BSC 0.008 0.015 0.125 0.170 0.300 BSC 0_ 15 _ 0.020 0.040 MILLIMETERS MIN MAX 19.05 19.93 6.10 7.49 −−− 5.08 0.39 0.50 1.27 BSC 1.40 1.65 2.54 BSC 0.21 0.38 3.18 4.31 7.62 BSC 0_ 15 _ 0.51 1.01 MC10H100 PACKAGE DIMENSIONS PDIP−16 P SUFFIX PLASTIC DIP PACKAGE CASE 648−08 ISSUE R −A− 16 9 1 8 B F C NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. L S SEATING PLANE −T− H K G D M J 16 PL 0.25 (0.010) M T A M DIM A B C D F G H J K L M S INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0_ 10 _ 0.020 0.040 MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0_ 10 _ 0.51 1.01 MECL 10H and MECL 10K are trademarks of Motorola, Inc. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 61312, Phoenix, Arizona 85082−1312 USA Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051 Phone: 81−3−5773−3850 http://onsemi.com 5 ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative. MC10H100/D