a High-Speed, 5 V, 0.1 F CMOS RS-232 Drivers/Receivers ADM222/ADM232A/ADM242 FUNCTIONAL BLOCK DIAGRAM FEATURES 200 kB/s Transmission Rate Small (0.1 F) Charge Pump Capacitors Single 5 V Power Supply Meets All EIA-232-E and V.28 Specifications Two Drivers and Two Receivers On-Board DC-DC Converters 9 V Output Swing with 5 V Supply 30 V Receiver Input Levels Pin Compatible with MAX222/MAX232A/MAX242 5V INPUT 0.1F C1+ 0.1F C1– C2+ 0.1F VCC +5V TO +10V V+ VOLTAGE DOUBLER +5V TO –10V VOLTAGE INVERTER V– 0.1F C2– APPLICATIONS Computers Peripherals Modems Printers Instruments TTL/CMOS INPUTS* TTL/CMOS OUTPUTS T1IN T1 T1OUT T2IN T2 T2OUT R1OUT R1 R1IN R2OUT R2 R2IN ADM2xx GENERAL DESCRIPTION The ADM222, ADM232A, ADM242 are a family of high-speed RS-232 line drivers/receivers offering transmission rates up to 200 kB/s. Operating from a single 5 V power supply, a highly efficient on-chip charge pump using small (0.1 µF) external capacitors allows RS-232 bipolar levels to be developed. Two RS-232 drivers and two RS-232 receivers are provided on each device. The devices are fabricated on BiCMOS, an advanced mixed technology process that combines low power CMOS with highspeed bipolar circuitry. This allows for transmission rates up to 200 kB/s, yet minimizes the quiescent power supply current to under 5 mA. The ADM232A is a pin-compatible, high-speed upgrade for the AD232 and for the ADM232L. It is available in 16-lead DIP and in both narrow and wide surface-mount (SOIC) packages. The ADM222 contains an additional shutdown (SHDN) function that may be used to disable the device, thereby reducing the supply current to 0.1 µA. During shutdown, all transmit/receive 0.1F EN GND SHDN RS-232 OUTPUTS RS-232 INPUTS** (ADM242) (ADM222, ADM242) * INTERNAL 400k PULL-UP RESISTOR ON EACH TTL/CMOS INPUT ** INTERNAL 5k PULL-DOWN RESISTOR ON EACH RS-232 INPUT functions are disabled. The ADM222 is available in 18-lead DIP and in a wide surface-mount (SOIC) package. The ADM242 combines both shutdown (SHDN) and enable (EN) functions. The shutdown function reduces the supply current to 0.1 mA. During shutdown, the transmitters are disabled but the receivers continue to operate normally. The enable function allows the receiver outputs to be disabled thereby facilitating sharing a common bus. The ADM242 is available in 18-lead DIP and in a wide surface-mount (SOIC) package. REV. B Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 World Wide Web Site: http://www.analog.com Fax: 781/461-3113 © Analog Devices, Inc., 2010 (VCC = 5 V 10%. C1–C4 = 0.1 F; all specMIN to TMAX unless otherwise noted.) ADM222/ADM232A/ADM242–SPECIFICATIONS ifications T Parameter Min Typ RS-232 TRANSMITTERS Output Voltage Swing ±5 ±9 2.4 1.7 1.7 12 Input Logic Threshold Low, VINL Input Logic Threshold High, VINH Logic Pull-Up Current Data Rate Output Resistance Output Short Circuit Current (Instantaneous) RS-232 RECEIVERS RS-232 Input Voltage Range RS-232 Input Threshold Low RS-232 Input Threshold High RS-232 Input Hysteresis RS-232 Input Resistance TTL/CMOS Output Voltage Low, VOL TTL/CMOS Output Voltage High, VOH TTL/CMOS Output Short-Circuit Current TTL/CMOS Output Short-Circuit Current TTL/CMOS Output Leakage Current EN Input Threshold Low, VINL EN Input Threshold High, VINH AC CHARACTERISTICS Transition Region Slew Rate Transmitter Propagation Delay TTL to RS-232 Receiver Propagation Delay RS-232 to TTL Receiver Output Enable Time Receiver Output Disable Time Transmitter Output Enable Time Transmitter Output Disable Time Transmitter + to – Propagation Delay Difference Receiver + to – Propagation Delay Difference 0.8 40 200 300 ± 10 –30 0.8 0.2 3 3.5 –2 10 2.0 POWER SUPPLY Power Supply Current Shutdown Power Supply Current SHDN Input Leakage Current SHDN Input Threshold Low, VINL SHDN Input Threshold High, VINH Max +30 1.2 1.6 0.4 5 0.05 2.4 1.0 7 0.4 –85 35 ± 0.05 ± 10 Unit Test Conditions/Comments V All Transmitter Outputs Loaded with 3 kΩ to Ground TIN TIN TIN = 0 V V V µA kB/s Ω mA V V V V kΩ V V mA mA µA VCC = V+ = V– = 0 V, VOUT = ± 2 V VCC = 5 V TA = 0°C to 85°C IOUT = 3.2 mA IOUT = –1.0 mA Source Current (VOUT = GND)* Sink Current (VOUT = VCC)* SHDN = GND/EN = VCC 0 V ≤ VOUT ≤ VCC 1.4 1.4 0.8 V V 4 13 0.1 8 mA mA µA µA V V No Load 3 kΩ Load on Both Outputs CL = 50 pF to 1000 pF, RL = 3 kΩ to 7 kΩ Measured from +3 V to –3 V or –3 V to +3 V tPHLT tPLHT tPHLR tPLHR tER tDR SHDN Goes High SHDN Goes Low 10 ±1 0.8 2.0 1.4 1.4 3 8 30 V/µs 0.85 1.0 0.1 0.3 125 160 250 3.5 150 200 3.5 3.5 0.5 0.5 500 500 µs µs µs µs ns ns µs µs ns ns *Guaranteed by design, not production tested. Specifications subject to change without notice. –2– REV. B ADM222/ADM232A/ADM242 ABSOLUTE MAXIMUM RATINGS* (TA = 25°C unless otherwise noted) VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 V V+ . . . . . . . . . . . . . . . . . . . . . . . . . . . (VCC – 0.3 V) to +13 V V– . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +0.3 V to –13 V Input Voltages TIN . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to (VCC + 0.3 V) RIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 30 V Output Voltages TOUT . . . . . . . . . . . . . . . . . . . (V+, +0.3 V) to (V–, –0.3 V) ROUT . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to (VCC + 0.3 V) Short Circuit Duration TOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous Power Dissipation N-16 . . . . . . . . . . . . . . . . . . . . . . 400 mW (Derate 7.5 mW/°C above 70°C) θJA, Thermal Impedance . . . . . . . . . . . . . . . . . . . . 80°C/W Power Dissipation R-16N . . . . . . . . . . . . . . . . . . . . . 400 mW (Derate 7 mW/°C above 70°C) θJA, Thermal Impedance . . . . . . . . . . . . . . . . . . . . 80°C/W Power Dissipation R-16W . . . . . . . . . . . . . . . . . . . . . 400 mW (Derate 7 mW/°C above 70°C) θJA, Thermal Impedance . . . . . . . . . . . . . . . . . . . . 80°CW Power Dissipation N-18 . . . . . . . . . . . . . . . . . . . . . . 400 mW (Derate 7 mW/°C above 70°C) θJA, Thermal Impedance . . . . . . . . . . . . . . . . . . . . 80°C/W Power Dissipation R-18W . . . . . . . . . . . . . . . . . . . . . 400 mW (Derate 7 mW/°C above 70°C) θJA, Thermal Impedance . . . . . . . . . . . . . . . . . . . . 80°C/W Operating Temperature Range Industrial (A Version) . . . . . . . . . . . . . . . –40°C to +85°C Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C Lead Temperature (Soldering, 10 sec) . . . . . . . . . . . . 300°C Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . 215°C Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220°C *This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. Test Circuits 3V 3V VIN VIN t PLHT 0V t PHLR t PHLT t PLHR VCC V+ VOUT VOUT 0V 50% GND V– Figure 1. Transmitter Propagation Delay Timing Figure 3. Receiver Propagation Delay Timing 3V EN INPUT 3V 0V EN INPUT 0V t DR t ER VOH VOH – 0.5V 3.5V RECEIVER OUTPUT RECEIVER OUTPUT VOL + 0.5V 0.8V VOL Figure 2. Receiver Enable Timing REV. B Figure 4. Receiver Disable Timing –3– ADM222/ADM232A/ADM242 PIN FUNCTION DESCRIPTION VOUT VIN 3k 50pF SHDN Mnemonic Function VCC V+ Power Supply Input, 5 V ± 10%. Internally generated positive supply (+10 V nominal). Internally generated negative supply (–10 V nominal). Ground Pin. Must be connected to 0 V. External capacitor 1, (+ terminal) is connected to this pin. External capacitor 1, (– terminal) is connected to this pin. External capacitor 2, (+ terminal) is connected to this pin. External capacitor 2, (– terminal) is connected to this pin. Transmitter (Driver) Inputs. These inputs accept TTL/CMOS levels. An internal 400 kΩ pull-up resistor to VCC is connected on each input. Transmitter (Driver) Outputs. These are RS-232 levels (typically ± 9 V). Receiver Inputs. These inputs accept RS-232 signal levels. An internal 5 kΩ pull-down resistor to GND is connected on each of these inputs. Receiver Outputs. These are TTL/CMOS levels. No Connect. No connections are required to this pin. (ADM242 Only) Active Low Digital Input. May be used to enable or disable (three-state) both receiver outputs. (ADM222 and ADM242) Active Low Digital Input. May be used to disable the device so that the power consumption is minimized. On the ADM222 all drivers and receivers are disabled. On the ADM242 the drivers are disabled but the receivers remain enabled. V– Figure 5. Shutdown Test Circuit GND C1+ 3V SHDN INPUT C1– 0V C2+ t DT C2– V+ + 5V TIN TRANSMITTER OUTPUT TOUT – 5V RIN V– Figure 6. Transmitter Shutdown Disable Timing ROUT NC 5V INPUT EN C5 0.1F 6.3V 2 C1 0.1F 4 5 C2 0.1F T1IN TTL/CMOS INPUTS* T2IN 6 C1+ C1– C2+ 17 VCC 3 +5V TO +10V V+ VOLTAGE DOUBLER +5V TO –10V 7 VOLTAGE INVERTER V– C2– 12 15 T1 11 8 T2 13 R1OUT TTL/CMOS OUTPUTS R1 10 R2OUT R2 ADM222 14 9 18 C3 0.1F SHDN C4 0.1F T1OUT T2OUT RS-232 OUTPUTS R1IN R2IN RS-232 INPUTS** 18 17 VCC V+ 3 16 GND 15 T1OUT C1– 4 ADM222 SHDN TOP VIEW 14 R1IN (Not to Scale) C2– 6 13 R1OUT C2+ 5 SHDN GND 16 NC 1 C1+ 2 * INTERNAL 400k PULL-UP RESISTOR ON EACH TTL/CMOS INPUT ** INTERNAL 5k PULL-DOWN RESISTOR ON EACH RS-232 INPUT V– 7 12 T1IN T2OUT 8 11 T2IN R2IN 9 10 R2OUT NC = NO CONNECT Figure 7. ADM222 Typical Operating Circuit Figure 8. ADM222 DIP and SOIC Pin Configurations –4– REV. B ADM222/ADM232A/ADM242 EN 1 C1+ 1 V+ 2 C2+ 4 ADM232A 17 VCC 16 GND V+ 3 15 GND C1– 3 18 SHDN C1+ 2 16 VCC 14 T1OUT C1– 4 13 R1IN C2+ 5 ADM242 TOP VIEW C2– 5 (Not to Scale) 12 R1OUT V– 6 11 T1IN V– 7 12 T1IN T2OUT 7 10 T2IN T2OUT 8 11 T2IN R2IN 8 9 R2IN 9 R2OUT Figure 9. ADM232A DIP/SOIC Pin Configuration 10 R2OUT Figure 11. ADM242 DIP/SOIC Pin Configuration 5V INPUT 5V INPUT C5 0.1F 6.3V 1 C1 0.1F 3 4 C2 0.1F T1IN TTL/CMOS INPUTS* T2IN 5 C1+ C1– C2+ 16 VCC 2 +5V TO +10V V+ VOLTAGE DOUBLER +5V TO –10V 6 VOLTAGE INVERTER V– C2– 11 14 T1 10 7 T2 12 R2OUT C5 0.1F 6.3V C3 0.1F 2 C1 0.1F R1 9 R2 13 8 C2 0.1F C4 0.1F T1IN T1OUT T2OUT TTL/CMOS INPUTS* RS-232 OUTPUTS R2IN C1– C2+ 17 VCC 3 +5V TO +10V V+ VOLTAGE DOUBLER +5V TO –10V 7 VOLTAGE INVERTER V– C2– 12 15 T1 11 8 T2 14 R1OUT RS-232 INPUTS** TTL/CMOS OUTPUTS R2OUT EN GND 15 T2IN 6 C1+ 13 R1IN ADM232A R1 C3 0.1F C4 0.1F T1OUT T2OUT R1IN 9 10 R2IN R2 1 ADM242 18 RS-232 OUTPUTS RS-232 INPUTS** SHDN GND 16 * INTERNAL 400k PULL-UP RESISTOR ON EACH TTL/CMOS INPUT ** INTERNAL 5k PULL-DOWN RESISTOR ON EACH RS-232 INPUT * INTERNAL 400k PULL-UP RESISTOR ON EACH TTL/CMOS INPUT ** INTERNAL 5k PULL-DOWN RESISTOR ON EACH RS-232 INPUT Figure 10. ADM232A Typical Operating Circuit REV. B 4 5 R1OUT TTL/CMOS OUTPUTS 15 T1OUT TOP VIEW 14 R1IN (Not to Scale) C2– 6 13 R1OUT Figure 12. ADM242 Typical Operating Circuit –5– ADM222/ADM232A/ADM242 –Typical Performance Characteristics 15 15 10 10 V+ Tx O/P VOLTAGE – V Tx O/P HI V+, V– – V 5 0 –5 5 0 –5 Tx O/P LO V– –10 –10 –15 0 5 10 15 20 LOAD CURRENT – mA 25 –15 30 TPC 1. Charge Pump V+, V– vs. Current 0 2 4 6 8 10 LOAD CURRENT – mA 12 14 TPC 4. Transmitter Output Voltage vs. Current 9 TRANSMITTER OUTPUT VOLTAGE – V 115kBps 7 230kBps 5 A4 0.010V 115kBps 3 100 90 1 –1 –3 460kBps 10 –5 0% 460kBps –7 –9 230kBps 0 500 1000 1500 2000 LOAD CAPACITANCE – pF 2500 5V 5V 100s 3000 TPC 2. Transmitter Baud Rate vs. Load Capacitance TPC 5. Charge Pump V+, V– Exiting Shutdown T T : 6.2V : 140ns @: –3.5V : 6.0V : 600ns @: –2.9V T CH1 T 10.0V CH2 5.00V M 1.00s CH2 –6.4V CH1 TPC 3. Transmitter Unloaded Slew Rate 10.0V CH2 5.00V M 1.00s CH2 –6.4V TPC 6. Transmitter Fully Loaded Slew Rate –6– REV. B ADM222/ADM232A/ADM242 GENERAL INFORMATION The ADM222/ADM232A/ADM242 are high-speed RS-232 drivers/receivers requiring a single digital 5 V supply. The RS-232 standard requires transmitters that will deliver ± 5 V minimum on the transmission channel and receivers that can accept signal levels down to ± 3 V. The parts achieve this by integrating stepup voltage converters and level-shifting transmitters and receivers onto the same chip. CMOS technology is used to keep the power dissipation to an absolute minimum. All devices contain an internal charge pump voltage doubler and a voltage inverter that generates ± 10 V from the 5 V input. Four external 0.1 µF capacitors are required for the internal charge pump voltage converter. The ADM222/ADM232A/ADM242 is a modification, enhancement and improvement to the AD230-AD241 family and derivatives thereof. It is essentially plug-in-compatible and does not have materially different applications. CIRCUIT DESCRIPTION The internal circuitry consists of four main sections. These are: Charge Pump Voltage Converter TTL/CMOS to RS-232 Transmitters RS-232 to TTL/CMOS Receivers Enable and Shutdown Functions. Charge Pump DC-DC Voltage Converter The Charge Pump Voltage converter consists of an oscillator and a switching matrix. The converter generates a ± 10 V supply from the input 5 V level. This is done in two stages using a switched capacitor technique. The 5 V input supply is doubled to 10 V using capacitor C1 as the charge storage element. The –10 V level is also generated from the input 5 V supply using C1 and C2 as the storage elements. Capacitors C3 and C4 are used to reduce the output ripple. Their values are not critical and can be reduced if higher levels of ripple are acceptable. The charge pump capacitors C1 and C2 may also be reduced at the expense of higher output impedance on the V+ and V– supplies. The input threshold levels are both TTL- and CMOS-compatible with the switching threshold set at VCC/4. With a nominal VCC = 5 V, the switching threshold is 1.25 V typical. Unused inputs may be left unconnected, as an internal 400 kΩ pull-up resistor pulls them high forcing the outputs into a low state. As required by the RS-232 standard, the slew rate is limited to less than 30 V/µs without the need for an external slew limiting capacitor, and the output impedance in the power-off state is greater than 300 Ω. Receiver Section The receivers are inverting level-shifters that accept RS-232 input levels (± 3 V to ± 15 V) and translate them into 5 V TTL/ CMOS levels. The inputs have internal 5 kΩ pull-down resistors to ground and are also protected against overvoltages of up to ± 30 V. The guaranteed switching thresholds are 0.8 V minimum and 2.4 V maximum, which are well within the ± 3 V RS-232 requirement. The low level threshold is deliberately positive as it ensures that an unconnected input will be interpreted as a low level. The receivers have Schmitt trigger input with a hysteresis level of 0.5 V. This ensures error-free reception for both noisy inputs and for inputs with slow transition times Enable and Shutdown Functions On the ADM222, both receivers are fully disabled during shutdown. On the ADM242, both receivers continue to operate normally. This function is useful for monitoring activity so that when it occurs, the device can be taken out of the shutdown mode. The ADM242 also contains a receiver enable function (EN) which can be used to fully disable the receivers, independent of SHDN. APPLICATIONS INFORMATION A selection of typical operating circuits is shown in TPCs 1–6 and Figure 13. The V+ and V– supplies may also be used to power external circuitry if the current requirements are small. Please refer to the typical performance characteristics which shows the V+, V– output voltage vs. current. A1 2.0V 5V 5V 100 90 In the shutdown mode the charge pump is disabled and V+ decays to VCC while V– decays to 0 V. 10 Transmitter (Driver) Section 0% The Drivers convert TTL/CMOS input levels into RS-232 output levels. With VCC = 5 V and driving a typical RS-232 load, the output voltage swing is ± 9 V. Even under worst-case conditions the drivers are guaranteed to meet the ± 5 V RS-232 minimum requirement. REV. B 5s Figure 13. Transmitter Output Disable Timing –7– ADM222/ADM232A/ADM242 OUTLINE DIMENSIONS 0.800 (20.32) 0.790 (20.07) 0.780 (19.81) 16 9 1 0.280 (7.11) 0.250 (6.35) 0.240 (6.10) 8 0.325 (8.26) 0.310 (7.87) 0.300 (7.62) 0.100 (2.54) BSC 0.060 (1.52) MAX 0.210 (5.33) MAX 0.195 (4.95) 0.130 (3.30) 0.115 (2.92) 0.015 (0.38) MIN 0.150 (3.81) 0.130 (3.30) 0.115 (2.92) 0.015 (0.38) GAUGE PLANE SEATING PLANE 0.022 (0.56) 0.018 (0.46) 0.014 (0.36) 0.014 (0.36) 0.010 (0.25) 0.008 (0.20) 0.430 (10.92) MAX 0.005 (0.13) MIN 0.070 (1.78) 0.060 (1.52) 0.045 (1.14) 073106-B COMPLIANT TO JEDEC STANDARDS MS-001-AB CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. CORNER LEADS MAY BE CONFIGURED AS WHOLE OR HALF LEADS. Figure 14. 16-Lead Plastic Dual In-Line Package [PDIP] Narrow Body (N-16) Dimensions shown in inches and (millimeters) 10.50 (0.4134) 10.10 (0.3976) 9 16 7.60 (0.2992) 7.40 (0.2913) 8 1.27 (0.0500) BSC 0.30 (0.0118) 0.10 (0.0039) COPLANARITY 0.10 0.51 (0.0201) 0.31 (0.0122) 10.65 (0.4193) 10.00 (0.3937) 2.65 (0.1043) 2.35 (0.0925) SEATING PLANE 0.75 (0.0295) 0.25 (0.0098) 45° 8° 0° 0.33 (0.0130) 0.20 (0.0079) COMPLIANT TO JEDEC STANDARDS MS-013- AA CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. 1.27 (0.0500) 0.40 (0.0157) 032707-B 1 Figure 15. 16-Lead Standard Small Outline Package [SOIC_W] Wide Body (RW-16) Dimensions shown in millimeters and (inches) –8– REV. B ADM222/ADM232A/ADM242 10.00 (0.3937) 9.80 (0.3858) 4.00 (0.1575) 3.80 (0.1496) 9 16 1 8 1.27 (0.0500) BSC 1.75 (0.0689) 1.35 (0.0531) 0.25 (0.0098) 0.10 (0.0039) COPLANARITY 0.10 6.20 (0.2441) 5.80 (0.2283) SEATING PLANE 0.51 (0.0201) 0.31 (0.0122) 0.50 (0.0197) 0.25 (0.0098) 45° 8° 0° 0.25 (0.0098) 0.17 (0.0067) 1.27 (0.0500) 0.40 (0.0157) COMPLIANT TO JEDEC STANDARDS MS-012-AC 060606-A CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. Figure 16. 16-Lead Standard Small Outline Package [SOIC_N] Narrow Body (R-16) Dimensions shown in millimeters and (inches) 11.75 (0.4626) 11.35 (0.4469) 18 10 7.60 (0.2992) 7.40 (0.2913) 9 2.65 (0.1043) 2.35 (0.0925) 0.30 (0.0118) 0.10 (0.0039) COPLANARITY 0.10 10.65 (0.4193) 10.00 (0.3937) 1.27 (0.0500) BSC 0.51 (0.0201) 0.31 (0.0122) SEATING PLANE 0.75 (0.0295) 0.25 (0.0098) 8° 0° 0.33 (0.0130) 0.20 (0.0079) COMPLIANT TO JEDEC STANDARDS MS-013-AB CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. Figure 17. 18-Lead Standard Small Outline Package [SOIC_W] Wide Body (RW-18) Dimensions shown in millimeters and (inches) REV. B –9– 45° 1.27 (0.0500) 0.40 (0.0157) 060706-A 1 ADM222/ADM232A/ADM242 0.920 (23.37) 0.900 (22.86) 0.880 (22.35) 18 10 1 9 0.280 (7.11) 0.250 (6.35) 0.240 (6.10) 0.325 (8.26) 0.310 (7.87) 0.300 (7.62) 0.100 (2.54) BSC 0.060 (1.52) MAX 0.210 (5.33) MAX 0.195 (4.95) 0.130 (3.30) 0.115 (2.92) 0.015 (0.38) MIN 0.150 (3.81) 0.130 (3.30) 0.115 (2.92) 0.015 (0.38) GAUGE PLANE SEATING PLANE 0.022 (0.56) 0.018 (0.46) 0.014 (0.36) 0.005 (0.13) MIN 0.014 (0.36) 0.010 (0.25) 0.008 (0.20) 0.430 (10.92) MAX COMPLIANT TO JEDEC STANDARDS MS-001 CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. CORNER LEADS MAY BE CONFIGURED AS WHOLE OR HALF LEADS. 070706-A 0.070 (1.78) 0.060 (1.52) 0.045 (1.14) Figure 18. 18-Lead Plastic Dual In-Line Package [PDIP] Narrow Body (N-18) Dimensions shown in inches and (millimeters) ORDERING GUIDE Model1 ADM222AN ADM222ANZ ADM222AR ADM222ARZ ADM222ARZ-REEL ADM232AAN ADM232AANZ ADM232AARN ADM232AARN-REEL ADM232AARN-REEL7 ADM232AARNZ ADM232AARNZ-REEL ADM232AARNZ-REEL7 ADM232AARW ADM232AARW-REEL ADM232AARWZ ADM232AARWZ-REEL ADM242AN ADM242ANZ ADM242AR ADM242AR-REEL ADM242ARZ ADM242ARZ-REEL 1 Temperature Range −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C Package Description 18-Lead PDIP 18-Lead PDIP 18-Lead SOIC_W 18-Lead SOIC_W 18-Lead SOIC_W 16-Lead PDIP 16-Lead PDIP 16-Lead SOIC_N 16-Lead SOIC_N 16-Lead SOIC_N 16-Lead SOIC_N 16-Lead SOIC_N 16-Lead SOIC_N 16-Lead SOIC_W 16-Lead SOIC_W 16-Lead SOIC_W 16-Lead SOIC_W 18-Lead PDIP 18-Lead PDIP 18-Lead SOIC_W 18-Lead SOIC_W 18-Lead SOIC_W 18-Lead SOIC_W Package Option N-18 N-18 RW-18 RW-18 RW-18 N-16 N-16 R-16 R-16 R-16 R-16 R-16 R-16 RW-16 RW-16 RW-16 RW-16 N-18 N-18 RW-18 RW-18 RW-18 RW-18 Z = RoHS Compliant Part. –10– REV. B ADM222/ADM232A/ADM242 REVISION HISTORY 11/10—Rev. A to Rev. B Updated Outline Dimensions ......................................................... 9 Changes to Ordering Guide .......................................................... 10 ©2010 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D01213-0-11/10(B) REV. B –11–