LM48556 www.ti.com SNAS452B – JUNE 2008 – REVISED MAY 2013 LM48556 Boomer™ Fully Differential, Mono, Ceramic Speaker Driver Check for Samples: LM48556 FEATURES DESCRIPTION • • • • • The LM48556 is a single supply, mono, ceramic speaker driver with an integrated charge-pump, designed for portable devices, such as cell phones, where board space is at a premium. The LM48556 charge pump allows the device to deliver 17.5VPP (typ) from a single 4.5V supply. Additionally, the charge pump features a soft start function that minimizes transient current during power-up. 1 23 Fully Differential Amplifier Externally Configurable Gain Integrated Charge Pump Low Power Shutdown Mode Soft Start Function APPLICATIONS • • • Mobile Phones PDA's Digital Cameras KEY SPECIFICATIONS • • • • Output Voltage Swing – VDD = 3.6V, 1kHz 14.2VPP (typ) – VDD = 4.5V, 1kHz 17.5VPP (typ) Power Supply Rejection Ratio – f = 217Hz, VDD = 3.6V 80dB (typ) IDD at VDD = 3.6V 4.8mA (typ) Wake-Up Time 0.5ms (typ) The LM48556 features high power supply rejection ratio (PSRR) of 80dB at 217Hz, allowing the device to operate in noisy environments without additional power supply conditioning. Flexible power supply requirements allow operation from 2.7V to 5.0V. Additionally, the LM48556 features a differential input function and an externally configurable gain. A low power shutdown mode reduces supply current consumption to 0.1μA. Superior click and pop suppression eliminates audible transients on power-up/down and during shutdown. The LM48556 is available in an ultra-small 12-bump DSBGA package (2mm x 1.5mm). 1 2 3 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Boomer is a trademark of Texas Instruments. All other trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2008–2013, Texas Instruments Incorporated LM48556 SNAS452B – JUNE 2008 – REVISED MAY 2013 www.ti.com TYPICAL APPLICATION R F200 k: C FR F+ 82 pF 200 k: VDD C F+ 82 pF C S1 C S2 0.1 PF 4.7 PF RIN+ C IN+ SVDD PVDD 0.47 P F 20 k: IN+ RO 15: OUT- CL 1 PF OUT+ INC IN- R IN- Ceramic Speaker Load 0.47 PF 20 k: C1P SHUTDOWN SD Shutdown Control Charge Pump C1 4.7 PF C1N CPVSS PGND SVSS C SS 10 PF Figure 1. Typical Audio Amplifier Application Circuit Connection Diagram A B C D 3 IN+ IN- SD PVDD 2 SVDD OUT+ C1P PGND 1 OUT- SVSS CPVSS C1N Figure 2. 12 Bump DSBGA - Top View See Package Number YZR00121AA 2 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM48556 LM48556 www.ti.com SNAS452B – JUNE 2008 – REVISED MAY 2013 Figure 3. 12 Bump DSBGA - Package View BUMP DESCRIPTIONS Bump Name A1 OUT- Amplifier Inverting Output Description A2 SVDD Signal Power Supply - Positive A3 IN+ B1 SVSS Amplifier Non-inverting Input Signal Power Supply - Negative B2 OUT+ Amplifier Non-inverting Output B3 IN- C1 CPVSS C2 C1P Charge Pump Flying Capacitor Positive Terminal C3 SD Active Low Reset Input. Connect to VDD for normal operation. Drive SD low to disable. Amplifier Inverting Input Charge Pump Output Voltage D1 C1N D2 PGND Charge Pump Flying Capacitor Negative Terminal Power Ground D3 PVDD Power Supply Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM48556 3 LM48556 SNAS452B – JUNE 2008 – REVISED MAY 2013 www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Absolute Maximum Ratings (1) (2) (3) Supply Voltage (SVDD, PVDD) (1) 5.25V −65°C to +150°C Storage Temperature −0.3V to VDD + 0.3V Input Voltage Power Dissipation (4) Internally limited ESD Rating (5) 2000V ESD Rating (6) 200V Junction Temperature 150°C θJA (YZR) Thermal Resistance 114°C/W Soldering Information (1) (2) (3) (4) (5) (6) See AN-1112 (SNVA009) Micro SMD Wafer Level Chip Scale “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur, including inoperability and degradation of device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or other conditions beyond those indicated in the Recommended Operating Conditions is not implied. The Recommended Operating Conditions indicate conditions at which the device is functional and the device should not be operated beyond such conditions. All voltages are measured with respect to the ground pin, unless otherwise specified. The Electrical Characteristics tables list ensured specifications under the listed Recommended Operating Conditions except as otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and are not ensured. If Military/Aerospace specified devices are required, please contact the TI Sales Office/ Distributors for availability and specifications. The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, θJA, and the ambient temperature, TA. The maximum allowable power dissipation is PDMAX = (TJMAX - TA) / θJA or the number given in Absolute Maximum Ratings, whichever is lower. Human body model, applicable std. JESD22-A114C. Machine model, applicable std. JESD22-A115-A. Operating Ratings Temperature Range TMIN ≤ TA ≤ TMAX −40°C ≤ TA ≤ +85°C 2.7V ≤ _VDD ≤ 5.0V Supply Voltage (SVDD, PVDD) Electrical Characteristics VDD = 3.6V (1) The following specifications apply for VDD = 3.6V, AV-BTL = 20dB (R F = 200kΩ, RIN = 20kΩ), ZL = 15Ω+1μF, unless otherwise specified. Limits apply for TA = 25°C. Symbol Parameter LM48556 Conditions Typical (2) Limit (3) Units (Limits) IDD Quiescent Power Supply Current VIN = 0V 4.8 7 mA (max) ISD Shutdown Current VSD = GND (Note 8) 0.1 1 µA (max) VOS Output Offset Voltage CIN = 0.47μF, AV = 1V/V (0dB) 0.6 4 mV (max) TWU Wake-up Time VOUT Output Voltage Swing THD+N Total Harmonic Distortion + Noise 0.5 ms THD+N = 1% (max); f = 1kHz 14.2 VPP THD+N = 1% (max); f = 10kHz 11.5 11 VPP (min) VOUT = 11VPP, f = 1kHz AV = 0dB 0.005 % AV = 20dB 0.03 % μV εOS Output Noise A-weighted filter, VIN = 0V Input referred 8 PSRR Power Supply Rejection Ratio VRIPPLE = 200mVPP, f = 217Hz 80 (1) (2) (3) 4 60 dB (min) The Electrical Characteristics tables list ensured specifications under the listed Recommended Operating Conditions except as otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and are not ensured. Typical values represent most likely parametric norms at TA = +25ºC, and at the Recommended Operation Conditions at the time of product characterization and are not ensured. Datasheet min/max specification limits are specified by test or statistical analysis. Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM48556 LM48556 www.ti.com SNAS452B – JUNE 2008 – REVISED MAY 2013 Electrical Characteristics VDD = 3.6V(1) (continued) The following specifications apply for VDD = 3.6V, AV-BTL = 20dB (R F = 200kΩ, RIN = 20kΩ), ZL = 15Ω+1μF, unless otherwise specified. Limits apply for TA = 25°C. Symbol Parameter Conditions Input Referred LM48556 Typical (2) Limit (3) Units (Limits) 60 dB (min) CMRR Common Mode Rejection Ratio VLH Logic High Threshold Voltage 70 1.2 V (min) VLL Logic Low Threshold Voltage 0.45 V (max) Electrical Characteristics VDD = 4.5V (1) The following specifications apply for VDD = 4.5V, AV-BTL = 20dB (R F = 200kΩ, RIN = 20kΩ), ZL = 15Ω+1μF, unless otherwise specified. Limits apply for TA = 25°C. Symbol Parameter Conditions LM48556 Typical (2) Limit (3) Units (Limits) IDD Quiescent Power Supply Current VIN = 0V 6.5 10 mA (max) ISD Shutdown Current VSD = GND (Note 8) 0.1 1 µA (max) VOS Output Offset Voltage CIN = 0.47μF, AV = 1V/V (0dB) 0.6 4 mV (max) TWU Wake-up Time VOUT Output Voltage Swing 0.5 ms (max) THD+N = 1% (max); f = 1kHz 17.5 VPP THD+N = 1% (max); f = 10kHz 14.6 14 VPP (min) VOUT = 14VPP, f = 1kHz THD+N Total Harmonic Distortion + Noise AV = 0dB 0.005 % AV = 20dB 0.03 % 8 μV εOS Output Noise A-weighted filter, VIN = 0V Input referred PSRR Power Supply Rejection Ratio VRIPPLE = 200mVPP, f = 217Hz, 80 CMRR Common Mode Rejection Ratio Input Referred 70 VLH Logic High Threshold Voltage 1.2 V (min) VLL Logic Low Threshold Voltage 0.45 V (max) (1) (2) (3) 60 dB (min) 60 dB (min) The Electrical Characteristics tables list ensured specifications under the listed Recommended Operating Conditions except as otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and are not ensured. Typical values represent most likely parametric norms at TA = +25ºC, and at the Recommended Operation Conditions at the time of product characterization and are not ensured. Datasheet min/max specification limits are specified by test or statistical analysis. Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM48556 5 LM48556 SNAS452B – JUNE 2008 – REVISED MAY 2013 www.ti.com Typical Performance Characteristics ( ZL = 15Ω+1μF, AV = 20dB, BW = 22kHz) THD+N vs Frequency VDD = 2.7V, VO = 8VPP 10 10 1 THD+N (%) THD+N (%) 1 0.1 0.01 0.1 0.01 0.001 20 200 2k 0.001 20 20k 200 2k FREQUENCY (Hz) FREQUENCY (Hz) Figure 4. Figure 5. THD+N vs Frequency VDD = 4.5V, VO = 17.5VPP 10 10 1 0.1 20k THD+N vs Output Voltage Swing VDD = 2.7V, f = 1kHz f = 10 kHz 1 THD+N (%) THD+N (%) THD+N vs Frequency VDD = 3.6V, VO = 14.2VPP 0.1 f = 1 kHz 0.01 0.01 f = 100 Hz 0.001 20 200 2k 20k 0.001 10m 100m 1 10 FREQUENCY (Hz) OUTPUT VOLTAGE SWING (VRMS) Figure 7. THD+N vs Output Voltage Swing VDD = 3.6V, f = 1kHz THD+N vs Output Voltage Swing VDD = 4.5V, f = 1kHz THD+N (%) 1 10 f = 10 kHz 1 THD+N (%) 10 Figure 6. 0.1 f = 1 kHz f = 10 kHz 0.1 f = 1 kHz 0.01 0.01 f = 100 Hz 0.001 10m 100m f = 100 Hz 1 10 0.001 10m OUTPUT VOLTAGE SWING (VRMS) 1 10 OUTPUT VOLTAGE SWING (VRMS) Figure 8. 6 100m Figure 9. Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM48556 LM48556 www.ti.com SNAS452B – JUNE 2008 – REVISED MAY 2013 Typical Performance Characteristics (continued) ( ZL = 15Ω+1μF, AV = 20dB, BW = 22kHz) CMRR vs Frequency VDD = 3.6V, Input referred 0 -10 -10 -20 -20 -30 -30 CMRR (dB) 0 -40 -50 -60 -40 -50 -60 -70 -70 -80 -80 -90 -90 -100 20 -100 20 200 2k 20k FREQUENCY (Hz) Figure 11. CMRR vs Frequency VDD = 4.5V, Input referred PSRR vs Frequency VDD = 2.7V, Input referred 0 0 -10 -20 -20 -30 -30 -40 -50 -60 -50 -60 -70 -70 -80 -80 -90 -90 -100 20 -100 20 200 2k 20k 200 2k Figure 13. PSRR vs Frequency VDD = 3.6V, Input referred PSRR vs Frequency VDD = 4.5V, Input referred 0 -10 -20 -20 -30 -30 PSRR (dB) 0 -10 -40 -50 -60 -40 -50 -60 -70 -70 -80 -80 -90 -90 2k 20k FREQUENCY (Hz) Figure 12. 200 20k -40 FREQUENCY (Hz) PSRR (dB) 2k Figure 10. -10 -100 20 200 FREQUENCY (Hz) PSRR (dB) CMRR (dB) CMRR (dB) CMRR vs Frequency VDD = 2.7V, Input referred 20k -100 20 FREQUENCY (Hz) 200 2k 20k FREQUENCY (Hz) Figure 14. Figure 15. Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM48556 7 LM48556 SNAS452B – JUNE 2008 – REVISED MAY 2013 www.ti.com Typical Performance Characteristics (continued) ( ZL = 15Ω+1μF, AV = 20dB, BW = 22kHz) Output Voltage vs Frequency VDD = 2.7V, THD+N = 1% 6.0 OUTPUT VOLTAGE (VRMS) OUTPUT VOLTAGE (VRMS) 4.00 3.75 3.50 3.25 3.00 10 100 Output Voltage vs Frequency VDD = 3.6V, THD+N = 1% 1k 5.5 5.0 4.5 4.0 10 10k 100 FREQUENCY (Hz) FREQUENCY (Hz) Figure 17. Output Voltage vs Frequency VDD = 4.5V, THD+N = 1% Supply Current vs Supply Voltage VIN = GND, No Load 6.5 6.5 6.0 6.0 5.5 5.5 5.0 4.5 4.0 2.7 5.0 10 100 1k 10k 3.0 3.3 3.6 3.9 4.2 4.5 SUPPLY VOLTAGE (V) FREQUENCY (Hz) Figure 18. Figure 19. Power Consumption vs Output Voltage Swing VDD = 2.7V, THD+N ≤ 1% Power Consumption vs Output Voltage Swing VDD = 3.6V, THD+N ≤ 1% 500 800 POWER CONSUMPTION (mW) POWER CONSUMPTION (mW) 450 400 350 f = 10 kHz 300 250 200 150 f = 1 kHz 100 50 0.00 700 600 500 f = 10 kHz 400 300 200 f = 1 kHz 100 0 0 1 2 3 4 OUTPUT VOLTAGE SWING (VRMS) Figure 20. 8 10k Figure 16. SUPPLY CURRENT (mA) OUTPUT VOLTAGE (VRMS) 7.0 1k 0 1 2 3 4 5 OUTPUT VOLTAGE SWING (VRMS) Figure 21. Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM48556 LM48556 www.ti.com SNAS452B – JUNE 2008 – REVISED MAY 2013 Typical Performance Characteristics (continued) ( ZL = 15Ω+1μF, AV = 20dB, BW = 22kHz) Power Consumption vs Output Voltage Swing VDD = 4.5V, THD+N ≤ 1% POWER CONSUMPTION (mW) 1200 1000 800 f = 10 kHz 600 400 f = 1 kHz 200 0 0 1 2 3 4 5 OUTPUT VOLTAGE SWING (VRMS) Figure 22. Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM48556 9 LM48556 SNAS452B – JUNE 2008 – REVISED MAY 2013 www.ti.com APPLICATION INFORMATION GENERAL AMPLIFIER FUNCTION The LM48556 is a fully differential ceramic speaker driver that utilizes TI’s inverting charge pump technology to deliver the high drive voltages required by ceramic speakers, without the need for noisy, board-space consuming inductive based regulators. The low-noise, inverting charge pump creates a negative supply (CPVSS) from the positive supply (PVDD). Because the amplifiers operate from these bipolar supplies, the maximum output voltage swing for each amplifier is doubled compared to a traditional single supply device. Additionally, the LM48556 is configured as a bridge-tied load (BTL) device, quadrupling the maximum theoretical output voltage range when compared to a single supply, single-ended output amplifier, see Bridge Configuration Explained section. The charge pump and BTL configuration allow the LM48556 to deliver over 17VP-P at 1kHz to a 1µF ceramic speaker while operating from a single 4.5V supply . DIFFERENTIAL AMPLIFIER EXPLANATION The LM48556 features a differential input stage, which offers improved noise rejection compared to a singleended input amplifier. Because a differential input amplifier amplifies the difference between the two input signals, any component common to both signals is cancelled. An additional benefit of the differential input structure is the possible elimination of the DC input blocking capacitors. Since the DC component is common to both inputs, and thus cancelled by the amplifier, the LM48556 can be used without input coupling capacitors when configured with a differential input signal. BRIDGE CONFIGURATION EXPLAINED The LM48556 is designed to drive a load differentially, a configuration commonly referred to as a bridge-tied load (BTL). The BTL configuration differs from the single-ended configuration, where one side of the load is connected to ground. A BTL amplifier offers advantages over a single-ended device. Driving the load differentially doubles the output voltage compared to a single-ended amplifier under similar conditions. Any component common to both outputs is cancelled, thus there is no net DC voltage across the load, eliminating the DC blocking capacitors required by single-ended, single-supply amplifiers. SHUTDOWN FUNCTION The LM48556 features a low current shutdown mode. Set SD = GND to disable the amplifier and reduce supply current to 0.1µA. Switch SD between VDD and GND for minimum current consumption in shutdown. The LM48556 may be disabled with shutdown voltages less than 0.45V, however, the idle current will be greater than the typical 0.1µA value. PROPER SELECTION OF EXTERNAL COMPONENTS Power Supply Bypassing/Filtering Proper power supply bypassing is critical for low noise performance and high PSRR. Place the supply bypass capacitors as close to the device as possible. Place a 4.7µF tantalum capacitor in parallel with a 0.1µF ceramic capacitor from VDD to GND. Additional bulk capacitance may be added as required. Charge Pump Capacitor Selection Use low ESR ceramic capacitors (less than 100mΩ) for optimum performance. Charge Pump Flying Capacitor (C1) The flying capacitor (C1) affects the load regulation and output impedance of the charge pump. A C1 value that is too low results in a loss of current drive, leading to a loss of amplifier headroom. A higher valued C1 improves load regulation and lowers charge pump output impedance to an extent. Above 4.7µF, the RDS(ON) of the charge pump switches and the ESR of C1 and CSS dominate the output impedance. A lower value capacitor can be used in systems with low maximum output power requirements. 10 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM48556 LM48556 www.ti.com SNAS452B – JUNE 2008 – REVISED MAY 2013 Charge Pump Hold Capacitor (CSS) The value and ESR of the hold capacitor (CSS) directly affects the ripple on CPVSS. Increasing the value of CSS reduces output ripple. Decreasing the ESR of CSS reduces both output ripple and charge pump output impedance. A lower value capacitor can be used in systems with low maximum output power requirements. Gain Setting Resistor Selection The amplifier gain of the LM48556 is set by four external resistors, two per each input, RIN_ and RF_ Figure 1. The amplifier gain is given by Equation 1: AV = RF / RIN (V/V) (1) Careful matching of the resistor pairs, RF+ and RF-, and RIN+ and RIN-, is required for optimum performance. Any mismatch between the resistors results in a differential gain error that leads to an increase in THD+N, decrease in PSRR and CMRR, as well as an increase in output offset voltage. Resistors with a tolerance of 1% or better are recommended. The gain setting resistors should be placed as close to the device as possible. Keeping the input traces close together and of the same length increases noise rejection in noisy environments. Noise coupled onto the input traces which are physically close to each other will be common mode and easily rejected. Feedback Capacitor Selection Due to their capacitive nature, ceramic speakers poorly reproduce high frequency audio content. At high frequencies, a ceramic speaker presents a low impedance load to the amplifier, increasing the required drive current. The higher output current can drive the device into clipping, increasing THD+N. Low-pass filtering the audio signal improves audio quality by decreasing the signal amplitude at high frequencies, reducing the speaker drive current. Adding a capacitor in parallel with each feedback resistor creates a simple low-pass filter with the 3dB point determined by Equation 2: f−3dB = 1 / 2πRFCF (Hz) Where • • RF is the value of the feedback resistor determined by Equation 1 in the Gain Setting Resistor Selection section CF is the value of the feedback capacitor (2) The feedback capacitor is optional and not required for normal operation. Input Capacitor Selection Input capacitors block the DC component of the audio signal, eliminating any conflict between the DC component of the audio source and the bias voltage of the LM48556. The input capacitors create a high-pass filter with the input resistors RIN. The -3dB point of the high pass filter is found using Equation 3 below. f = 1 / 2πRINCIN (Hz) Where • the value of RIN is determined by Equation 1 in the Gain Setting Resistor Selection section (3) When the LM48556 is using a single-ended source, power supply noise on the ground is seen as an input signal. Setting the high-pass filter point above the power supply noise frequencies, 217Hz in a GSM phone, for example, filters out the noise such that it is not amplified and heard on the output. Capacitors with a tolerance of 1% or better are recommended for impedance matching and improved CMRR and PSRR. SINGLE-ENDED AUDIO AMPLIFIER CONFIGURATION The LM48556 is compatible with single-ended sources. Figure 4 shows the typical single-ended applications circuit. Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM48556 11 LM48556 SNAS452B – JUNE 2008 – REVISED MAY 2013 www.ti.com RF CIN RIN IN+ OUT- IN- OUT+ RIN CIN RF Figure 23. Single-Ended Input Configuration Bill Of Materials Component Description Designator Footprint LM48556TL LM48556TL 1 Capacitor 4.7μF, ceramic, low ESR (<0.1Ω) 16V, -40°C to +85°C C1 CR3216-1206 1 Capacitor 82μF, 16V, -40°C to +85°C CF+ CR2012-0805 1 Capacitor 82μF, 16V, -40°C to +85°C CF- CR2012-0805 1 Capacitor 0.47μF, 16V, -40°C to +85° CIN+ CR2012-0805 1 Capacitor 0.47μF, 16V, -40°C to +85°C CIN- CR2012-0805 1 Capacitor 4.7μF, 16V, -40°C to +85°C CS1 CR3216-1206 1 Capacitor 0.1μF ceramic, 16V, -40°C to +85°C CS2 CR2012-0805 1 Capacitor 10μF ceramic, low ESR (<0.1Ω) 16V, -40°C to +85°C CSS CR3216-1206 1 Header, 2–Pin Header 2 IN HDR1X2 1 Resistor 200kΩ RF+ CR2012-0805 1 Resistor 200kΩ RF+ CR2012-0805 1 Resistor 200kΩ RIN+ CR2012-0805 1 Resistor 200kΩ RIN- CR2012-0805 1 Header, 2–Pin Header 2 SPEAKER HDR1X2 1 Header, 2–Pin Header 2 VDD HDR1X2 1 Header, 3–Pin 3–pole jumper J1 3–pole jumper 1 LM48556TL LM48556TL 12 Submit Documentation Feedback Quantity Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM48556 LM48556 www.ti.com SNAS452B – JUNE 2008 – REVISED MAY 2013 Demonstration Board Schematic RF+ 200 k : CF+ VDD 82 pF 1 2 RF200 k : CF- VDD 82 pF S1 4.7 PF A3 IN+ OUT- OUT+ 20 k : LM48556TL VDD J1 2 2 3 SD C3 SD D2 3 B2 C2 OUT- OUT+ C1N D1 2 1 C1P 1 SVSS 1 C1P A1 C1N C1 4.7 PF B1 0.47 PF 20 k : RIN+ CPVSS 0.47 PF CIN+ C1 1 2 IN- SVDD B3 PVDD RIN- PGND CININ A2 D3 0.1 PF SPEAKER CS2 +C CSS 10 PF Demonstration Board PCB Views Figure 24. Top Overlay Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM48556 13 LM48556 SNAS452B – JUNE 2008 – REVISED MAY 2013 www.ti.com Figure 25. Top Layer Figure 26. Mid Layer 1 14 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM48556 LM48556 www.ti.com SNAS452B – JUNE 2008 – REVISED MAY 2013 Figure 27. Mid Layer 2 Figure 28. Bottom Overlay Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM48556 15 LM48556 SNAS452B – JUNE 2008 – REVISED MAY 2013 www.ti.com Figure 29. Bottom Layer 16 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM48556 LM48556 www.ti.com SNAS452B – JUNE 2008 – REVISED MAY 2013 REVISION HISTORY Rev Date 1.0 06/03/08 Initial release. Description 1.01 12/09/08 Changed Power Supply Voltage Limits from 4.5V to 5.0V. B 05/02/2013 Changed layout of National Data Sheet to TI format Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM48556 17 PACKAGE OPTION ADDENDUM www.ti.com 2-May-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (°C) Top-Side Markings (3) (4) LM48556TL/NOPB ACTIVE DSBGA YZR 12 250 Green (RoHS & no Sb/Br) SNAGCU Level-1-260C-UNLIM GK4 LM48556TLX/NOPB ACTIVE DSBGA YZR 12 3000 Green (RoHS & no Sb/Br) SNAGCU Level-1-260C-UNLIM GK4 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Top-Side Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 Samples PACKAGE MATERIALS INFORMATION www.ti.com 8-May-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) LM48556TL/NOPB DSBGA YZR 12 250 178.0 8.4 LM48556TLX/NOPB DSBGA YZR 12 3000 178.0 8.4 Pack Materials-Page 1 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 1.68 2.13 0.76 4.0 8.0 Q1 1.68 2.13 0.76 4.0 8.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 8-May-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM48556TL/NOPB DSBGA YZR LM48556TLX/NOPB DSBGA YZR 12 250 210.0 185.0 35.0 12 3000 210.0 185.0 35.0 Pack Materials-Page 2 MECHANICAL DATA YZR0012xxx 0.600±0.075 D E TLA12XXX (Rev C) D: Max = 2.012 mm, Min =1.951 mm E: Max = 1.512 mm, Min =1.452 mm 4215049/A NOTES: A. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.5M-1994. B. This drawing is subject to change without notice. www.ti.com 12/12 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2015, Texas Instruments Incorporated