Vishay CRCW0805562RZKTB Lead (pb)-bearing thick film, rectangular chip resistor Datasheet

D/CRCW
Vishay
Lead (Pb)-Bearing Thick Film, Rectangular Chip Resistors
FEATURES
• Stability ΔR/R = 1 % for 1000 h at 70 °C
• Lead (Pb)-bearing termination plating on Ni barrier layer
• Metal glaze on high quality ceramic
• Halogen-free according to IEC 61249-2-21 definiton
• AEC-Q200 qualified, rev. C compliant
STANDARD ELECTRICAL SPECIFICATIONS
SIZE
MODEL
D10/CRCW0402
INCH
METRIC
0402 RR 1005M
RATED DISSIPATION
P70
W
0.063
LIMITING
RESISTANCE
TEMPERATURE
ELEMENT
TOLERANCE
RANGE
COEFFICIENT
VOLTAGE
%
Ω
ppm/K
Umax. AC/DC
50
± 100
± 200
SERIES
±1
±5
1R0 to 10M
E24; E96
E24
±1
±5
1R0 to 10M
E24; E96
E24
±1
±5
1R0 to 10M
E24; E96
E24
±1
±5
1R0 to 10M
E24; E96
E24
±1
±5
1R0 to 10M
E24; E96
E24
±1
±5
1R0 to 2M2
E24; E96
E24
±1
±5
1R0 to 10M
E24; E96
E24
±1
±5
1R0 to 10M
E24; E96
E24
Zero-Ohm-Resistor: Rmax. = 20 mΩ, Imax. = 1.5 A
D11/CRCW0603
0603 RR 1608M
0.10
75
± 100
± 200
Zero-Ohm-Resistor: Rmax. = 20 mΩ, Imax. = 2.0 A
D12/CRCW0805
0805 RR 2012M
0.125
150
± 100
± 200
Zero-Ohm-Resistor: Rmax. = 20 mΩ, Imax. = 2.5 A
D25/CRCW1206
1206 RR 3216M
0.25
200
± 100
± 200
Zero-Ohm-Resistor: Rmax. = 20 mΩ, Imax. = 3.5 A
CRCW1210
1210 RR 3225M
0.50
200
± 100
± 200
Zero-Ohm-Resistor: Rmax. = 20 mΩ, Imax. = 5.0 A
CRCW1218
1218 RR 3246M
1.0
200
± 100
± 200
Zero-Ohm-Resistor: Rmax. = 20 mΩ, Imax. = 7.0 A
CRCW2010
2010 RR 5025M
0.75
400
± 100
± 200
Zero-Ohm-Resistor: Rmax. = 20 mΩ, Imax. = 6.0 A
CRCW2512
2512 RR 6332M
1.0
500
± 100
± 200
Zero-Ohm-Resistor: Rmax. = 20 mΩ, Imax. = 7.0 A
Notes
• These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over
operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime.
• Marking: See datasheet “Surface Mount Resistor Marking” (document number 20020).
• Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material.
www.vishay.com
118
For technical questions, contact: [email protected]
Document Number: 20008
Revision: 18-Nov-10
D/CRCW
Lead (Pb)-Bearing Thick Film, Rectangular Chip Resistors
Vishay
TECHNICAL SPECIFICATIONS
D10/
D11/
D12/
D25/
UNIT CRCW0402
CRCW0603 CRCW0805 CRCW1206 CRCW1210 CRCW1218 CRCW2010 CRCW2512
PARAMETER
Rated dissipation at 70 °C (1)
W
0.063
0.1
0.125
0.25
0.5
1.0
0.75
1.0
Limiting element voltage
UMAX. AC/DC
V
50
75
150
200
200
200
400
500
Insulation voltage UINS.
(1 min)
V
> 75
> 100
> 200
> 300
> 300
> 300
> 300
> 300
Insulation resistance
Ω
> 109
Category temperature range
°C
- 55 to + 155
Failure rate
h-1
< 0.1 x 10-9
Weight
mg
29.5
25.5
40.5
0.65
2
5.5
10
16
Note
(1) The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the
printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded.
PART NUMBER AND PRODUCT DESCRIPTION
Part Number: CRCW0805562RFKTA (2)
C
R
C
MODEL
CRCW0402
CRCW0603
CRCW0805
CRCW1206
CRCW1210
CRCW1218
CRCW2010
CRCW2512
W
0
8
0
VALUE
R = Decimal
K = Thousand
M = Million
0000 = Jumper
5
5
6
2
TOLERANCE
F=±1%
J=±5%
Z = Jumper
R
F
K
TCR
K = ± 100 ppm/K
N = ± 200 ppm/K
S = Jumper or
special
T
A
PACKAGING
TA
TB
TC
TD
TE
TF
TG
TH
TK
SPECIAL
Up to 2 digits
Product Description: CRCW0805 100 562R 1 % RT1
CRCW0805
MODEL
CRCW0402
CRCW0603
CRCW0805
CRCW1206
CRCW1210
CRCW1218
CRCW2010
CRCW2512
100
562R
1%
RT1
TCR
RESISTANCE VALUE
TOLERANCE
PACKAGING
± 100 ppm/K
± 200 ppm/K
10R = 10 Ω
562R = 562 Ω
10K = 10.0 kΩ
1M = 1 MΩ
0R0 = Jumper
±1%
±5%
RT1
RT5
RT6
RT7
RF4
R02
R67
R82
RT9
Note
(2) Preferred way for ordering products is by use of the PART NUMBER.
Document Number: 20008
Revision: 18-Nov-10
For technical questions, contact: [email protected]
www.vishay.com
119
D/CRCW
Lead (Pb)-Bearing Thick Film, Rectangular Chip Resistors
Vishay
PACKAGING
MODEL
PAPER TAPE
ACC. IEC 60286-3, TYPE I
UNIT
BLISTER TAPE
ACC. IEC 60286-3, TYPE II
QUANTITY PART NUMBER PRODUCT DESC. QUANTITY PART NUMBER PRODUCT DESC.
D10/CRCW0402
180 mm/7"
10 000
TD
RT7
330 mm/13"
50 000
TE
RF4
180 mm/7"
5000
TA
RT1
10 000
TB
RT5
330 mm/13"
20 000
TC
RT6
180 mm/7"
5000
TA
RT1
10 000
TB
RT5
330 mm/13"
20 000
TC
RT6
180 mm/7"
5000
TA
RT1
RT5
D11/CRCW0603 285 mm/11.25"
D12/CRCW0805 285 mm/11.25"
D25/CRCW1206 285 mm/11.25"
CRCW1210
10 000
TB
330 mm/13"
20 000
TC
RT6
180 mm/7"
5000
TA
RT1
285 mm/11.25"
10 000
TB
RT5
330 mm/13"
20 000
TC
RT6
CRCW1218
180 mm/7"
4000
CRCW2010
180 mm/7"
CRCW2512
180 mm/7"
TK
RT9
4000
TF
R02
2000
TG
R67
4000
TH
R82
DIMENSIONS
SOLDER PAD DIMENSIONS in millimeters
SIZE
DIMENSIONS in millimeters
REFLOW SOLDERING
INCH
METRIC
L
0402
1005
1.0 ± 0.05
W
H
T1
T2
a
b
l
WAVE SOLDERING
a
b
l
0.5 ± 0.05
0.35 ± 0.05
0.25 ± 0.05
0.2 ± 0.1
0.4
0.6
0.5
0.85 ± 0.1
0.45 ± 0.05
0.3 ± 0.2
0.3 ± 0.2
0.5
0.9
1.0
0.9
0.9
1.0
0.3
0.3 ± 0.2
0.7
1.3
1.2
0.9
1.3
1.3
0603
1608
1.55
+ 0.10
- 0.05
0805
2012
2.0
+ 0.20
- 0.10
1.25 ± 0.15
0.45 ± 0.05
1206
3216
3.2
+ 0.10
- 0.20
1.6 ± 0.15
0.55 ± 0.05
0.45 ± 0.2
0.4 ± 0.2
0.9
1.7
2.0
1.1
1.7
2.3
1210
3225
3.2 ± 0.2
2.5 ± 0.2
0.55 ± 0.05
0.45 ± 0.2
0.4 ± 0.2
0.9
2.5
2.0
1.1
2.5
2.2
1218
3246
3.2
4.6 ± 0.15
0.55 ± 0.05
0.45 ± 0.2
0.4 ± 0.2
1.05
4.9
1.9
1.25
4.8
1.9
2010
5025
5.0 ± 0.15
2.5 ± 0.15
0.6 ± 0.1
0.6 ± 0.2
0.6 ± 0.2
1.0
2.5
3.9
1.2
2.5
3.9
2512
6332
6.3 ± 0.2
3.15 ± 0.15
0.6 ± 0.1
0.6 ± 0.2
0.6 ± 0.2
1.0
3.2
5.2
1.2
3.2
5.2
www.vishay.com
120
+ 0.10
- 0.20
+ 0.20
- 0.10
For technical questions, contact: [email protected]
Document Number: 20008
Revision: 18-Nov-10
D/CRCW
Lead (Pb)-Bearing Thick Film, Rectangular Chip Resistors
Vishay
Pulse Load Pmax. (W)
FUNCTIONAL PERFORMANCE
Single Pulse
1000
2512
1218
2010
1210
1206
0805
0603
0402
100
10
1
0.1
0.01
10-6
10-5
10-4
10-3
10-2
10-1
1
10
100
Pulse Duration t i (s)
Maximum pulse load, single pulse; applicable if P 0 and n < 1000 and Û ≤ Ûmax.;
for permissible resistance change equivalent to 8000 h operation
Continuous Pulse Load Pmax. (W)
Continuous Pulse
1000
2512
1218
2010
1210
1206
0805
0603
0402
100
10
1
0.1
0.01
10-6
10-5
10-4
10-3
10-2
10-1
1
10
100
Pulse Duration t i (s)
Maximum pulse load, continuous pulses; applicable if P ≤ P (ϑamb) and Û ≤ Ûmax.;
for permissible resistance change equivalent to 8000 h operation
Pulse Voltage Û max. (V)
Pulse Voltage
2000
1800
2512
1600
1400
2010
1200
1000
800
1206/1210/1218
600
400
0805
0603
200
0402
0 -6
10- 5
10
10- 4
10- 3
10- 2
10- 1
1
10
Pulse Duration t i (s)
Maximum pulse voltage, single and continuous pulses; applicable if
P ≤ Pmax.; for permissible resistance change equivalent to 8000 h operation
Document Number: 20008
Revision: 18-Nov-10
For technical questions, contact: [email protected]
www.vishay.com
121
D/CRCW
Vishay
Lead (Pb)-Bearing Thick Film, Rectangular Chip Resistors
Fraction of Rated Dissipation in %
Derating
120
100
80
60
40
20
0
- 55
- 25
0
25
50
75
70
100
125
155 175
Ambient Temperature in °C
Attenuation of 3rd Harmonic A3 in dB
Non-Linearity
120
100
80
1206, 2010
0805
60
0603
0402
40
20
0
10
100
1K
10K
100K
1M
10M
Resistance Value R in Ω
Current Noise A1 in µV/V
Current Noise
100
2
040
3
0
6
0
5
080 6
120 0
201
10
1
0.1
0.01
100
1K
10K
100K
1M
10M
Resistance Value R in Ω
www.vishay.com
122
For technical questions, contact: [email protected]
Document Number: 20008
Revision: 18-Nov-10
D/CRCW
Lead (Pb)-Bearing Thick Film, Rectangular Chip Resistors
Vishay
TEST PROCEDURES AND REQUIREMENTS
EN
60115-1
CLAUSE
PROCEDURE
IEC
60082-2
TEST
METHOD
TEST
Stability for product types:
D/CRCW
REQUIREMENTS PERMISSIBLE
CHANGE (ΔR)
STABILITY CLASS 1
OR BETTER
STABILITY CLASS 2
OR BETTER
1 Ω to 10 MΩ
1 Ω to 10 MΩ
±1%
±5%
4.5
-
Resistance
-
4.7
-
Voltage proof
U = 1.4 · Uins; 60 s
4.13
-
Short time overload
U = 2.5 x P 70 x R ≤ 2 x Umax.;
duration: Acc. to style
± (0.25 % R + 0.05 Ω)
4.17.2
58 (Td)
Solderability
Solder bath method; Sn60Pb40;
non-activated flux;
(235 ± 5) °C, (2 ± 0.2) s
Good tinning (≥ 95 %
covered);
no visible damage
4.8.4.2
-
Temperature coefficient
(20/- 55/20) °C and
(20/125/20) °C
± 100 ppm/K
4.32
21 (Uu3)
Shear (adhesion)
RR 1608 and smaller: 9 N
RR 2012 and larger: 45 N
No visible damage
4.33
21 (Uu1)
Substrate bending
Depth 2 mm; 3 times
No visible damage,
no open circuit in bent position
± (0.25 % R + 0.05 Ω)
± (0.5 % R + 0.05 Ω)
± 200 ppm/K
30 min. at - 55 °C;
30 min. at 125°C
4.19
14 (Na)
Rapid change of temperature
4.23
-
Climatic sequence:
2 (Ba)
Dry heat
125 °C; 16 h
4.23.2
No flashover or breakdown
5 cycles
1000 cycles
± (0.25 % R + 0.05 Ω)
± (1 % R + 0.05 Ω)
± (0.5 % R + 0.05 Ω)
± (1 % R + 0.05 Ω)
± (1 % R + 0.05 Ω)
± (2 % R + 0.1 Ω)
-
4.23.3
30 (Db)
Damp heat, cyclic
55 °C; ≥ 90 % RH;
24 h; 1 cycle
4.23.4
1 (Aa)
Cold
- 55 °C; 2 h
4.23.5
13 (M)
Low air pressure
1 kPa; (25 ± 10) °C; 1 h
4.23.6
30 (Db)
Damp heat, cyclic
55 °C; ≥ 90 % RH;
24 h; 5 cycles
4.23.7
-
DC load
U = P 70 x R
± (1 % R + 0.05 Ω)
± (2 % R + 0.1 Ω)
± (2 % R + 0.1 Ω)
± (4 % R + 0.1 Ω)
± (0.25 % R + 0.05 Ω)
± (0.5 % R + 0.05 Ω)
4.25.1
-
Endurance at 70 °C
U = √(P70 x R) ≤ Umax.
1.5 h on; 0.5 h off;
70 °C; 1000 h
70 °C; 8000 h
4.18.2
58 (Td)
Resistance to soldering heat
Solder bath method
(260 ± 5) °C; (10 ± 1) s
4.35
-
Flamability, needle flame test
IEC 60695-11-5;
10 s
No burning after 30 s
4.24
78 (Cab)
Damp heat, steady state
(40 ± 2) °C;
(93 ± 3) % RH; 56 days
± (1 % R + 0.05 Ω)
4.25.3
-
Endurance at upper
category temperature
155 °C; 1000 h
4.40
-
Electrostatic discharge
(human body model)
IEC 61340-3-1;
3 pos. + 3 neg. discharges;
ESD test voltage acc. to size
± (1 % R + 0.05 Ω)
4.29
45 (XA)
Component solvent resistance
Isopropyl alcohol;
50 °C; method 2
No visible damage
4.30
45 (XA)
Solvent resistance of marking
Isopropyl alcohol;
50 °C; method 1, toothbrush
Marking legible,
no visible damage
Document Number: 20008
Revision: 18-Nov-10
± (1 % R + 0.05 Ω)
For technical questions, contact: [email protected]
± (2 % R + 0.1 Ω)
www.vishay.com
123
D/CRCW
Lead (Pb)-Bearing Thick Film, Rectangular Chip Resistors
Vishay
TEST PROCEDURES AND REQUIREMENTS
EN
60115-1
CLAUSE
IEC
60082-2
TEST
METHOD
PROCEDURE
TEST
REQUIREMENTS PERMISSIBLE
CHANGE (ΔR)
STABILITY CLASS 1
OR BETTER
STABILITY CLASS 2
OR BETTER
1 Ω to 10 MΩ
1 Ω to 10 MΩ
± (0.25 % R + 0.05 Ω)
± (0.5 % R + 0.05 Ω)
Stability for product types:
D/CRCW
4.22
6 (Fc)
Vibration, endurance by
sweeping
4.37
-
Periodic electric overload
4.27
-
Single pulse high voltage
overload, 10 µs/700 µs
f = 10 Hz to 2000 Hz;
x, y, z ≤ 1.5 mm;
A ≤ 200 m/s2;
10 sweeps per axis
U=
15 x P 70 x R ≤ 2 x Umax.;
0.1 s on; 2.5 s off;
1000 cycles
± (1 % R + 0.05 Ω)
P 70 x R ≤ 2 x Umax.;
10 pulses
± (1 % R + 0,05 Ω)
Û = 10 x
All tests are carried out in accordance with the following specifications:
• EN 60115-1, generic specification
• EN 140400, sectional specification
• EN 140401-802, detail specification
• IEC 60068-2, environmental test procedures
Packaging of components is done in paper or blister tapes according to IEC 60286-3.
www.vishay.com
124
For technical questions, contact: [email protected]
Document Number: 20008
Revision: 18-Nov-10
Legal Disclaimer Notice
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Document Number: 91000
Revision: 11-Mar-11
www.vishay.com
1
Similar pages