Standard Product Reference Sheet FHR1105P-TR Features Package 1005(t=0.25mm) Type, water clear lens Outer Dimension 1.0 x 0.5 x 0.25mm ( L x W x H ) Product features ・Lead–free soldering compatible ・RoHS compliant Recommended Applications ・Communication Machine, Electric Household Appliances, OA/FA, Other General Applications 2012/10/30 Page : 1 FHR1105P-TR Outline Dimensions Unit :mm Weight :(0.29)mg Tolerance :±0.1 SYM. PART NAME REMARKS QTY. ① LED Die ＡlGanInP 1 ② Resin Epoxy Resin 1 ③ PCB Glass Fabrics 1 ④ Ｅｌｅｃｔｒｏｄｅ Au/Ni/Cu 2 Note: Outline Dimensions do not include the size of cutting burr around substrate and pin(electrodes) Recommended Pad Unit :mm Tolerance :±0.1 2012/10/30 Page : 2 FHR1105P-TR Specifications 【 Product Overview 】 Die Material AlGaInP Emitting Color Red Resin Color(Emitting Area) Clear 【 Absolute Maximum Ratings 】 (Ta=25℃) ITEM SYMBOL MAXIMUM RATINGS UNITS Power Dissipation Pd 48 mW Forward Current IF 20 mA Repetitive Peak Forward Current "1ms,1/20duty" IFRM 48 mA IF Derate Linearly from "25℃" ΔIF 0.27 mA/℃ IFRM Derate Linearly from "25℃" ΔIFRM 0.64 mA/℃ Reverse Voltage VR 5 V Operating Temperature T opr -40 ～ + 85 ℃ Storage Temperature T stg -40 ～ +100 ℃ Soldering Temperature "Reflow Soldering" Tsld 260MAX ℃ 2012/10/30 Page : 3 FHR1105P-TR Specifications 【 Electro and Optical Characteristics 】 (Ta=25℃) ITEM SYMBOL CONDITIONS MIN. TYP. MAX. UNITS Forward Voltage VF IF = 5mA - 1.9 2.4 V Reverse Current IR VR = 5V - - 100 μA Luminous Intensity IV IF = 5mA 22.5 32.0 45.0 mcd λp IF = 5mA - 632 - nm λd IF = 5mA 618 623 628 nm Δλ IF = 5mA - 15 - nm Peak Wavelength Dominant Wavelength Spectral Line Half Width Note: Above Luminous Intensity (IV) values and Dominant wavelength (λd) values are the setup value of the selection machine．【Tolerance : IV…±10%,λd…±1nm】 【 Sorting For Luminous Intensity and Dominant Wavelength 】 LEDs shall be sorted out into the following ranks of Luminous Intensity and Dominant Wavelength. Luminous Intensity (Iv) Rank Rank IV (mcd) MIN. MAX. A 22.5 32.0 B 32.0 45.0 Conditions IF =5mA Ta=25℃ Note: Above Luminous Intensity (IV) values are the setup value of the selection machine． 【Tolerance : IV…±10%】 2012/10/30 Page : 4 FHR1105P-TR Technical Data Spectral Distribution Condition: Ta = 25℃, IF =5mA 1.0 0.9 0.8 Relative Intensity 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 400 450 500 550 600 650 700 Wavelength: (nm) Spatial Distribution Condition: Ta = 25℃, IF=5mA X 100 0 X direction Y direction -30 30 Y -60 -90 -100 60 50 0 -50 0 50 100 90 Relative Intensity: (%) 2012/10/30 Page : 5 FHR1105P-TR Technical Data Forward Voltage vs. Forward Current Ambient Temperature vs. Forward Voltage Condition : Ta = -40～85℃ Condition: Ta = 25℃ 2.5 60℃ 85℃ 10 Forward Voltage: VF (V) Forward Current: I F (mA) 100 －40℃ －20℃ IF=20mA IF=10mA IF= 5mA 2.0 0℃ 25℃ IF= 2mA 1 1.5 2.0 2.5 1.5 -40 Forward Voltage: VF(V) -20 0 20 40 60 80 Ambient Temperature: Ta (℃) Ambient Temperature vs. Relative Intensity Forward Current vs. Relative Intensity Condition: IF = 5mA Condition: Ta = 25℃ 10 4.0 Relative Intensity Relative Intensity 3.0 2.0 1 1.0 0.1 0.0 0 5 10 Forward Current: IF (mA) 2012/10/30 15 20 -40 -20 0 20 40 60 80 Ambient Temperature: Ta (℃) Page : 6 FHR1105P-TR Technical Data Forward Current vs. Dominant Wavelength Ambient Temperature vs. Dominant Wavelength Condition: Ta = 25℃ Condition: IF = 5mA 630 Dominant Wavelength : λd (nm) Dominant Wavelength : λd (nm) 630 625 620 615 625 620 615 610 610 0 5 10 15 -40 20 -20 0 20 40 60 Forward Current: IF (mA) Ambient Temperature: Ta (℃) Max. Forward Current vs. Ambient Temperature Max. Forward Current vs. Duty Cycle Repetition Frequency: f ≧ 50Hz Condition: Ta = 25℃ 100 Maximum Forward Current : IFRM MAX. (mA) Maximum Forward Current : IFRM MAX. (mA) 50 80 Duty 5% 45 40 Duty 10% 35 30 Duty 20% 25 Duty 50% 20 DC 15 10 10 5 1 0 -40 -20 0 20 40 Ambient Temperature: Ta (℃) 2012/10/30 60 80 1 10 100 Duty cycle: D (%) Page : 7 F□□1105P-TR Soldering condition 【Soldering Precaution】 (acc.to EIAJ-4701/300) 1. Heat stress during soldering will greatly influence the reliability of LEDs, however that effect will vary on heating method. Also, if components of varying shape are soldered together, it is recommended to set the soldering pad temperature according to the component most vulnerable to heat stress (ex. SMT LED). (Recommended Condition: Soldering Pad temp. > Package temp.) 2. Because LED parts including the resin are not stable immediately after soldering ( when they are not at room temperature), any mechanical stress may cause damage to the product. Please avoid such stress after soldering, especially stacking of the boards which may cause the boards to warp and any other types of friction with hard materials.). 3. Recommended temperature profile for the Reflow soldering is listed as the temperature of the resin surface. Temperature distribution varies on heating method, PCB material, other components in the assembly, and mounting density . Please do not repeat the heating process in Reflow process more than twice. 【Recommended Reflow Soldering Condition.】 Peak Temperature (Soldering） 260℃ MAX. +1.5～+5℃/s -1.5～-5℃/s 230℃ MAX. 90~120sec MAX. （ Pre-heating） 150℃～180℃ 40sec MAX. Note 1 Temperature Profile for the reflow soldering is listed as the temperature of resin surface. This represents the maximum temperature ratings for soldering. Lowering the heating temperature and decreasing heating time is very effective in ensuring higher reliability. Note 2 The reflow soldering process should be done up to twice(2 times Max). When second process is performed, interval between first and second process should be as short as possible to prevent absorption of moisture to resin of LED. The second soldering process should not be done until LEDs have returned to room temperature (by nature-cooling) after first soldering process. 2012/10/30 Page : A-1 F□□1105P-TR Soldering condition 4. When using adhesive material for tentative fixatives, thermosetting resin or Ultraviolet radiation(UV) setting resin with heat shall be recommended. 《 The curing condition, Temperature:150℃Max./Time:120sec.Max.》 5. Manual soldering, dipping ( through the wave ) soldering cannot be used for this product. 6. Isopropyl alcohol is recommended for cleaning. Some chemicals, including Freon substitute detergent could corrode or affect the optical characteristics of the lens or the casing surface. Please review the reference chart below for cleaning. Cleaning with ultrasonic shall not be recommended. 2012/10/30 Chemical ○／× Isopropyl Alcohol Ethyl Alcohol Pure water Trichloroethylene Chlorothene Acetone Thinner ○ ○ ○ × × × × Page : A-2 Handling Precaution F□□1105P-TR 【 Other Precautions 】 1. Stanley LED Lamps have semiconductor characteristics and are designed to ensure high reliability. However, the performance may vary depending on usage conditions. 2. Absolute Maximum Ratings are set to prevent LED lamps from failing due to excess stress( temperature, current, voltage, etc.). Usage conditions must not exceed the ratings for a moment, nor do reach one item of absolute maximum rating s simultaneously. 3. In order to ensure high reliability from LED Lamps, variable factors that arise in actual usage conditions should be taken it to account for designing. ( Derating of TYP., MAX Forward Voltage, etc.) 4. Please insert Straight Protective Resistors into the circuit in order to stabilize LED operation and to prevent the device from igniting due to excess current. 5. Please avoid using the products with materials and products that contain sulfur and chorine element which will decrease the reliability of LED. Please keep LED in desiccator to protect them from corrosive gas regardless of whether mounting is finished or not. Also please make sure there is no gas occurs around or gas inflows from outside when using LED. 6. Please check the actual performance in the assembly because the Specification Sheets are described for single LED. 7. Please refrain from looking directly at the light source of LED at high output, as it may harm your vision. 8. The products are designed to operate without failure in recommended usage conditions. However, please take the necessary precautions to prevent fire, injury, and other damages should any malfunction or failure arise 9. The products are manufactured to be used for ordinary electronic equipment. Please contact our sales staff beforehand when exceptional quality and reliability are required, and the failure or malfunction of the products might directly jeopardize life or health ( such as for airplanes, aerospace, transport equipment, medical applications, nuclear reactor control systems and so on). 10. The formal specification sheets shall be valid only by exchange of documents signed by both parties. 2012/10/30 Page : A-3 F□□1105P-TR Packaging Specifications This product is baked (moisture removal) before packaging, and is shipped in moisture-proof packaging (as shown below) to minimize moisture absorption during transportation and storage. However, with regard to storing the products, Stanley recommends the use of dry-box under the following conditions is recommended. Moisture-proof bag as the packaging is made of anti-static material but packaging box is not. 【Recommended Storage Condition.】 Temperature +5～30℃ Humidity Under 70% Avoid storage in corroding and dusty environment. 【Time elapsed after Package Opening.】 The package should not be opened until immediately prior to its use, and please keep the time frame between package opening and soldering which is 【maximum 72h.】 If the device needs to be soldered twice, both soldering must be completed within the 72h. If any components should remain after their use, please seal the package and store them under the conditions described in the 【 Recommended Storage Condition 】. This product must be required to perform baking process (moisture removal) for at least 23h,not exceed for 48h, at 60+±5 degrees Celsius if following conditions apply. 1. In the case of silica gel (blue) which indicates the moisture level within the package, changes or loses its blue color. 2. In the case of time is passed for 72h after the package is opened once. Baking process should be performed after LED having been taken out of the package. Baking may be performed in the tape-reel form , however if it is performed with the reel stacked over one another, it may cause deformation of the reels and taping materials and later obstruct mounting. Please handle only once it has returned to room temperature. Provided that, baking process shall be 2 times MAX. 【Products WarrantyPeriod】 In the case of the package unopened , 6 months under 【 Recommended Storage Condition 】. Please avoid rapid transition from low temp. condition to high temp. condition. 2012/10/30 Page : A-4 F□□1105P-TR Packaging Specification 【Moisture-proof Packaging Specification】 Fastener for re-storage after opening bag. Customer's opening position. A Product Label Heat Sealing position (after product being put in) Desiccant with indicator for moisture level is enclosed. 2012/10/30 Page : A-5 F□□1105P-TR Packaging Specifications 【 Packing box 】 (RoHS・ELV Compliant) Box TYPE Outline dimension L × W × H (mm) Capacity of the box Type A 280 × 265 × 45 3 reel Type B 310 × 235 × 265 15 reel Type C 440 × 310 × 265 30 reel The above measure is all the reference value. Box for shipment is selected out of the above table, according to the shipping quantity. B Type A Material / box ： Cardoard C5BF 2012/10/30 Type B,C Material / box ： Cardoard K5AF Partition ： Cardoard K5BF Page : A-6 F□□1105P-TR Packaging Specifications 【Label Specification】 ( acc.to JIS-X0503(Code-39) ) A Product label A. Parts number B. Bar-code for parts number C. Parts code (In-house identification code for each parts number) D. Packed parts quantity E. Bar-Code for packed parts quantity F. Lot number & Rank (refer to Lot Number Notational System for details ) G. Bar-Code for Lot number & Rank B Opto device label A. Customer Name B. Parts Type C. Parts Code D. Parts Number E. Packed Parts Quantity F. Carton Number G. Shipping Date H. Bar-Code for In-house identification Number <Remark> Bar-code font : acc.to Code-39(JIX0503) 2012/10/30 Page : A-7 F□□1105P-TR Taping and Reel Specifications (acc.to JIS-C0806-03) 【Appearance】 Items Leader area Cover-tape Carrier-tape Trailer area 2012/10/30 Specifications Remarks Cover-tape shall be longer than 320mm without carrier-tape The end of cover-tape shall be held with adhesive tape. Empty pocket shall be more than 20 pieces. Please refer to the above figure for Taping & reel orientation . Empty pocket shall be more than 15 pieces. The end of taping shall be inserted into a slit of the hub. Page : A-8 F□□1105P-TR Taping and Reel Specifications (acc.to JIS-C0806-03) 【Qty. per Reel】 10，000parts/reel Minimum Qty. per reel might be 500 parts when getting less than 10,000 parts. In such case, parts of 500-unit-qty. shall be packed in a reel and the qty. shall be identified on the label 【Mechanical strength】 Cover-tape adhesive strength shall be 0.1～1.0N ( An angle between carrier-tape and cover-tape shall be170 deg. ) Both tapes shall be so sealed that the contained parts will not come out from the tape when it is bent at a radius of 15mm. 【Others】 Reversed-orientation, Up-side down placing, side placing and out of spec. parts mix shall not be held. Max qty. of empty pocket per reel shall be defined as follows. 2012/10/30 Qty./reel Max. qty. of empty pocket 1,000 2,000 3,000 4,000 5,000 6,000 7,000 8,000 9,000 10,000 1 2 3 4 5 6 7 8 9 10 Remark No continuance No continuance No continuance No continuance No continuance No continuance No continuance No continuance No continuance Page : A-9 F□□1105P-TR Taping and Reel Specifications (acc.to JIS-C0806-03) Unit :mm 【Taping Dimensions】 hole hole ③ 【Reel Dimensions】 2012/10/30 SYM. PART NAME REMARKS ① Carrier-tape Conductive Grade ② Cover-tape Anti-Static Grade ③ Carrier-reel Anti-Static Grade Page : A-10 F□□1105P-TR Lot Number Notational System ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ① - 1digit ： Production Location (Mark identify alphabet) ② - 1digit ： Production Year (Last Digit of Production Year shall be indicate as 2009→9,2010→0,2011→1,･･･) ③ - 2digit ： Production Month (Jan. to Sep. ,shall be indicated as 01,02,03,･････) ④ - 2digit ： Production Date ⑤ - 3digit ： Serial Number ⑥ - 2digit ： Tape and Reel following Number ⑦ - 2digit ： Luminous Intensity Rank. (If luminous intensity rank is 1 digit, "-" shall be dashed on the place for the second digit. If there is no identified rank, "- -" shall be used to indicate.) ⑧ - 2digit ： Chromaticity Rank (If chromaticity rank is 1 digit, "-" shall be dashed on the place for the second digit. If there is no identified rank, "- -" shall be used to indicate.) ⑨ - 1digit ： Option Rank (Stanley normally print "-" to indicate.) 2012/10/30 Page : A-11 Correspondence to RoHS・ELV instruction F□□1105P-TR This product is in compliance with RoHS・ELV. Prohibition substance and it's criteria value of RoHS・ELV are as follows. ・RoHS instruction …… Refer to following (1)～(6). ・ELV instruction ………. Refer to following (1)～(4). 2012/10/30 Substance Group Name Criteria Value (1) Lead and its compounds 1,000ppm Max (2) Cadmium and its compounds 100ppm Max (3) Mercury and its compounds 1,000ppm Max (4) Hexavalent chromium 1,000ppm Max (5) PBB 1,000ppm Max (6) PBDE 1,000ppm Max Page : A-12 F□□1105P-TR Reliability Testing Result Reference Test Item 1. Reliability Testing Result Standard Test Condition Duration Failure Ta = 25℃, IF = 20mA 1,000 h 0/20 Ta = 85℃, IF = 8mA 1,000 h 0/20 Ta = -40℃, IF = 20mA 1,000 h 0/20 1,000 h 0/20 Room Temperature Operating Life High Temperature Operating Life Low Temperature Operating Life EIAJ ED4701/100(101) EIAJ ED4701/100(101) EIAJ ED4701/100(101) Wet High Temperature Operating Life EIAJ ED4701/100(102) Ta = 60℃, RH = 90±5%,IF=14.6mA Thermal Shock EIAJ ED4701/100(105) Ta = -40℃~100℃(each 15min) 1,000 cycles 0/20 Resistance to Reflow Soldering EIAJ ED4701/300(301) Moisture Soak：30℃ 70% 96h Preheating：150～180℃ 120sec Max Soldering： 260 Peak 2times 0/20 Electrostatic Discharge(ESD) EIAJ ED4701/300(304) C=100pF R2=1.5kΩ±1000V once each polarity 0/20 2. Failure Criteria Item Symbol Condition Failure Criteria Luminous Intensity Iv IF＝５ｍA Testing Min. Value ＜Standard Min. Value × 0.5 Forward Voltage VF IF＝５ｍA Testing Max. Value≧ Standard Max. Value × 1.2 Cosmetic appearance - - Notable, discoloration, deformation and cracking 2012/10/30 Page : A-13 F□□1105P-TR Special Notice to Customers Using the Products and Technical Information Shown in This Data Sheet 1) The technical information shown in the data sheets are limited to the typical characteristics and circuit examples of the referenced products. It does not constitute the warranting of industrial property nor the granting of any license. 2) For the purpose of product improvement, the specifications, characteristics and technical data described in the data sheets are subject to change without prior notice. Therefore it is recommended that the most updated specifications be used in your design. 3) When using the products described in the data sheets, please adhere to the maximum ratings for operating voltage, heat dissipation characteristics, and other precautions for use. We are not responsible for any damage which may occur if these specifications are exceeded. 4) The products that have been described to this catalog are manufactured so that they will be used for the electrical instrument of the benchmark (OA equipment, telecommunications equipment, AV machine, home appliance and measuring instrument). The application of aircrafts, space borne application, transportation equipment, medical equipment and nuclear power control equipment, etc. needs a high reliability and safety, and the breakdown and the wrong operation might influence the life or the human body. Please consult us beforehand if you plan to use our product for the usages of aircrafts, space borne application, transportation equipment, medical equipment and nuclear power control equipment, etc. except OA equipment, telecommunications equipment, AV machine, home appliance and measuring instrument. 5) In order to export the products or technologies described in this data sheet which are under the “Foreign Exchange and Foreign Trade Control Law,” it is necessary to first obtain an export permit from the Japanese government. 6) No part of this data sheet may be reprinted or reproduced without prior written permission from Stanley Electric Co., Ltd. 7) The most updated edition of this data sheet can be obtained from the address below: http://www.stanley-components.com 2012/10/30 Page : A-14