Freescale MPC8270 Powerquiccâ ¢ ii family reference manual Datasheet

MPC8280 PowerQUICC™ II
Family Reference Manual
Supports
MPC8270
MPC8275
MPC8280
MPC8280RM
Rev. 1, 12/2005
How to Reach Us:
Home Page:
www.freescale.com
email:
[email protected]
USA/Europe or Locations Not Listed:
Freescale Semiconductor
Technical Information Center, CH370
1300 N. Alma School Road
Chandler, Arizona 85224
(800) 521-6274
480-768-2130
[email protected]
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
[email protected]
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku
Tokyo 153-0064, Japan
0120 191014
+81 2666 8080
[email protected]
Information in this document is provided solely to enable system and software
implementers to use Freescale Semiconductor products. There are no express or
implied copyright licenses granted hereunder to design or fabricate any integrated
circuits or integrated circuits based on the information in this document.
Freescale Semiconductor reserves the right to make changes without further notice to
any products herein. Freescale Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale Semiconductor assume any liability arising out of the application or use of
any product or circuit, and specifically disclaims any and all liability, including without
limitation consequential or incidental damages. “Typical” parameters which may be
provided in Freescale Semiconductor data sheets and/or specifications can and do
Asia/Pacific:
Freescale Semiconductor Hong Kong Ltd.
Technical Information Center
2 Dai King Street
Tai Po Industrial Estate,
Tai Po, N.T., Hong Kong
+800 2666 8080
[email protected]
vary in different applications and actual performance may vary over time. All operating
For Literature Requests Only:
Freescale Semiconductor
Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
(800) 441-2447
303-675-2140
Fax: 303-675-2150
LDCForFreescaleSemiconductor
@hibbertgroup.com
could create a situation where personal injury or death may occur. Should Buyer
parameters, including “Typicals” must be validated for each customer application by
customer’s technical experts. Freescale Semiconductor does not convey any license
under its patent rights nor the rights of others. Freescale Semiconductor products are
not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life,
or for any other application in which the failure of the Freescale Semiconductor product
purchase or use Freescale Semiconductor products for any such unintended or
unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all
claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale
Semiconductor was negligent regarding the design or manufacture of the part.
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. The described
product contains a PowerPC processor core. The PowerPC name is a trademark of IBM Corp. and
used under license. All other product or service names are the property of their respective owners.
© Freescale Semiconductor, Inc., 2005. All rights reserved.
Document Number: MPC8280RM
Rev. 1, 12/2005
Part I—Overview
Overview
G2_LE Core
Memory Map
Part II—Configuration and Reset
System Interface Unit (SIU)
Reset
Part III—The Hardware Interface
External Signals
60x Signals
The 60x Bus
PCI Bridge
Clocks and Power Control
Memory Controller
Secondary (L2) Cache Support
IEEE 1149.1 Test Access Port
Part IV—Communications Processor Module
Communications Processor Module Overview
Serial Interface with Time-Slot Assigner
CPM Multiplexing
Baud-Rate Generators (BRGs)
Timers
SDMA Channels and IDMA Emulation
Serial Communications Controllers (SCCs)
SCC UART Mode
SCC HDLC Mode
SCC BISYNC Mode
SCC Transparent Mode
SCC Ethernet Mode
SCC AppleTalk Mode
Universal Serial Bus Controller
Serial Management Controllers (SMCs)
Multi-Channel Controllers (MCCs)
Fast Communications Controllers (FCCs)
ATM Controller and AAL0, AAL1, and AAL5
ATM AAL1 Circuit Emulation Service
ATM AAL2
Inverse Multiplexing for ATM (IMA)
I
1
2
3
II
4
5
III
6
7
8
9
10
11
12
13
IV
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
I
1
2
3
II
4
5
III
6
7
8
9
10
11
12
13
IV
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Part I—Overview
Overview
G2_LE Core
Memory Map
Part II—Configuration and Reset
System Interface Unit (SIU)
Reset
Part III—The Hardware Interface
External Signals
60x Signals
The 60x Bus
PCI Bridge
Clocks and Power Control
Memory Controller
Secondary (L2) Cache Support
IEEE 1149.1 Test Access Port
Part IV—Communications Processor Module
Communications Processor Module Overview
Serial Interface with Time-Slot Assigner
CPM Multiplexing
Baud-Rate Generators (BRGs)
Timers
SDMA Channels and IDMA Emulation
Serial Communications Controllers (SCCs)
SCC UART Mode
SCC HDLC Mode
SCC BISYNC Mode
SCC Transparent Mode
SCC Ethernet Mode
SCC AppleTalk Mode
Universal Serial Bus Controller
Serial Management Controllers (SMCs)
Multi-Channel Controllers (MCCs)
Fast Communications Controllers (FCCs)
ATM Controller and AAL0, AAL1, and AAL5
ATM AAL1 Circuit Emulation Service
ATM AAL2
Inverse Multiplexing for ATM (IMA)
ATM Transmission Convergence Layer
Fast Ethernet Controller
FCC HDLC Controller
FCC Transparent Controller
Serial Peripheral Interface (SPI)
I2C Controller
Parallel I/O Ports
35
36
37
38
39
40
41
Register Quick Reference Guide
Revision History
A
B
Glossary
Index
GLO
IND
35
36
37
38
39
40
41
ATM Transmission Convergence Layer
Fast Ethernet Controller
FCC HDLC Controller
FCC Transparent Controller
Serial Peripheral Interface (SPI)
I2C Controller
Parallel I/O Ports
A
B
Register Quick Reference Guide
Revision History
GLO
IND
Glossary
Index
Contents
Paragraph
Number
Title
Page
Number
Contents
About This Book
Before Using this Manual—Important Note ................................................................ lxxxi
Audience ....................................................................................................................... lxxxi
Organization................................................................................................................. lxxxii
Suggested Reading...................................................................................................... lxxxiv
Conventions ................................................................................................................. lxxxv
Acronyms and Abbreviations ..................................................................................... lxxxvi
PowerPC Architecture Terminology Conventions...................................................... lxxxix
Part I
Overview
Chapter 1
Overview
1.1
1.2
1.2.1
1.2.2
1.2.3
1.3
1.3.1
1.4
1.5
1.6
1.6.1
1.6.2
1.7
1.7.1
1.7.1.1
1.7.1.2
1.7.1.3
1.7.1.4
1.7.1.5
1.7.1.6
1.7.2
1.7.2.1
Features ............................................................................................................................ 1-1
Architecture Overview..................................................................................................... 1-5
G2_LE Core................................................................................................................. 1-6
System Interface Unit (SIU) ........................................................................................ 1-7
Communications Processor Module (CPM) ................................................................ 1-7
Software Compatibility Issues ......................................................................................... 1-8
Signals.......................................................................................................................... 1-8
Differences Between MPC860 and MPC8280 .............................................................. 1-10
Serial Protocol Table...................................................................................................... 1-10
MPC8280 Configurations .............................................................................................. 1-11
Pin Configurations ..................................................................................................... 1-11
Serial Performance..................................................................................................... 1-11
Application Examples.................................................................................................... 1-12
Communication Systems ........................................................................................... 1-12
Remote Access Server ........................................................................................... 1-13
Regional Office Router.......................................................................................... 1-14
LAN-to-WAN Bridge Router ................................................................................ 1-14
Cellular Base Station ............................................................................................. 1-15
Telecommunications Switch Controller ................................................................ 1-16
SONET Transmission Controller........................................................................... 1-17
Bus Configurations .................................................................................................... 1-17
Basic System.......................................................................................................... 1-17
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
vii
Contents
Paragraph
Number
1.7.2.2
1.7.2.3
1.7.2.4
1.7.2.5
1.7.2.6
Title
Page
Number
High-Performance Communication....................................................................... 1-18
High-Performance System Microprocessor........................................................... 1-19
PCI ......................................................................................................................... 1-20
PCI with 155-Mbps ATM ...................................................................................... 1-20
The MPC8280 as PCI Agent ................................................................................. 1-21
Chapter 2
G2_LE Core
2.1
2.2
2.2.1
2.2.2
2.2.3
2.2.4
2.2.4.1
2.2.4.2
2.2.4.3
2.2.4.4
2.2.5
2.2.6
2.2.6.1
2.2.6.2
2.3
2.3.1
2.3.1.1
2.3.1.2
2.3.1.2.1
2.3.1.2.2
2.3.1.2.3
2.3.1.2.4
2.3.2
2.3.2.1
2.3.2.2
2.3.2.3
2.4
2.4.1
2.4.2
2.4.2.1
2.4.2.2
2.4.2.3
Overview.......................................................................................................................... 2-1
G2_LE Core Features ..................................................................................................... 2-3
Instruction Unit ............................................................................................................ 2-5
Instruction Queue and Dispatch Unit........................................................................... 2-5
Branch Processing Unit (BPU) .................................................................................... 2-6
Independent Execution Units....................................................................................... 2-6
Integer Unit (IU) ...................................................................................................... 2-6
Floating-Point Unit (FPU) ....................................................................................... 2-6
Load/Store Unit (LSU) ............................................................................................ 2-7
System Register Unit (SRU).................................................................................... 2-7
Completion Unit .......................................................................................................... 2-7
Memory Subsystem Support........................................................................................ 2-7
Memory Management Units (MMUs)..................................................................... 2-8
Cache Units.............................................................................................................. 2-8
Programming Model ........................................................................................................ 2-8
Register Set .................................................................................................................. 2-8
PowerPC Register Set.............................................................................................. 2-9
MPC8280-Specific Registers................................................................................. 2-11
Hardware Implementation-Dependent Register 0 (HID0) ................................ 2-11
Hardware Implementation-Dependent Register 1 (HID1) ................................ 2-14
Hardware Implementation-Dependent Register 2 (HID2) ................................ 2-14
Processor Version Register (PVR)..................................................................... 2-15
PowerPC Instruction Set and Addressing Modes ...................................................... 2-15
Calculating Effective Addresses............................................................................ 2-15
PowerPC Instruction Set........................................................................................ 2-16
MPC8280 Implementation-Specific Instruction Set.............................................. 2-17
Cache Implementation ................................................................................................... 2-18
PowerPC Cache Model.............................................................................................. 2-18
MPC8280 Implementation-Specific Cache Implementation..................................... 2-18
Data Cache............................................................................................................. 2-19
Instruction Cache ................................................................................................... 2-20
Cache Locking ....................................................................................................... 2-20
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
viii
Freescale Semiconductor
Contents
Paragraph
Number
2.4.2.3.1
2.4.2.3.2
2.5
2.5.1
2.5.2
2.6
2.6.1
2.6.2
2.7
2.8
Title
Page
Number
Entire Cache Locking ........................................................................................ 2-20
Way Locking...................................................................................................... 2-20
Exception Model............................................................................................................ 2-21
PowerPC Exception Model........................................................................................ 2-21
Implementation-Specific Exception Model ............................................................... 2-22
Memory Management.................................................................................................... 2-25
PowerPC Memory Management................................................................................ 2-25
Implementation-Specific MMU Features .................................................................. 2-25
Instruction Timing.......................................................................................................... 2-26
Differences Between the MPC8280 G2_LE
Embedded Core and the MPC603e............................................................................ 2-27
Chapter 3
Memory Map
3.1
Internal Memory Map...................................................................................................... 3-2
Part II
Configuration and Reset
Chapter 4
System Interface Unit (SIU)
4.1
4.1.1
4.1.2
4.1.3
4.1.4
4.1.5
4.2
4.2.1
4.2.1.1
4.2.1.2
4.2.2
4.2.2.1
4.2.2.2
4.2.2.3
4.2.3
4.2.4
4.2.4.1
4.3
System Configuration and Protection .............................................................................. 4-2
Bus Monitor ................................................................................................................. 4-3
Timers Clock................................................................................................................ 4-3
Time Counter (TMCNT).............................................................................................. 4-4
Periodic Interrupt Timer (PIT)..................................................................................... 4-5
Software Watchdog Timer ........................................................................................... 4-6
Interrupt Controller .......................................................................................................... 4-7
Interrupt Configuration................................................................................................ 4-8
Machine Check Interrupt ......................................................................................... 4-9
INT Interrupt............................................................................................................ 4-9
Interrupt Source Priorities............................................................................................ 4-9
SCC, FCC, and MCC Relative Priority ................................................................. 4-12
PIT, TMCNT, PCI, and IRQ Relative Priority ...................................................... 4-13
Highest Priority Interrupt....................................................................................... 4-13
Masking Interrupt Sources......................................................................................... 4-13
Interrupt Vector Generation and Calculation ............................................................. 4-14
Port C External Interrupts...................................................................................... 4-16
Programming Model ...................................................................................................... 4-17
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
ix
Contents
Paragraph
Number
4.3.1
4.3.1.1
4.3.1.2
4.3.1.3
4.3.1.4
4.3.1.5
4.3.1.6
4.3.1.7
4.3.2
4.3.2.1
4.3.2.2
4.3.2.3
4.3.2.4
4.3.2.5
4.3.2.6
4.3.2.7
4.3.2.8
4.3.2.9
4.3.2.10
4.3.2.11
4.3.2.12
4.3.2.13
4.3.2.14
4.3.2.15
4.3.2.16
4.3.3
4.3.3.1
4.3.3.2
4.3.3.3
4.3.4
4.3.4.1
4.3.4.2
4.4
Title
Page
Number
Interrupt Controller Registers .................................................................................... 4-17
SIU Interrupt Configuration Register (SICR)........................................................ 4-17
SIU Interrupt Priority Register (SIPRR)................................................................ 4-18
CPM Interrupt Priority Registers (SCPRR_H and SCPRR_L) ............................. 4-19
SIU Interrupt Pending Registers (SIPNR_H and SIPNR_L) ................................ 4-21
SIU Interrupt Mask Registers (SIMR_H and SIMR_L)........................................ 4-22
SIU Interrupt Vector Register (SIVEC) ................................................................. 4-24
SIU External Interrupt Control Register (SIEXR)................................................. 4-25
System Configuration and Protection Registers ........................................................ 4-26
Bus Configuration Register (BCR)........................................................................ 4-26
60x Bus Arbiter Configuration Register (PPC_ACR)........................................... 4-29
60x Bus Arbitration-Level Registers (PPC_ALRH/PPC_ALRL)......................... 4-30
Local Bus Arbiter Configuration Register (LCL_ACR) ....................................... 4-31
Local Bus Arbitration Level Registers (LCL_ALRH and LCL_ACRL) .............. 4-32
SIU Module Configuration Register (SIUMCR)................................................... 4-33
Internal Memory Map Register (IMMR)............................................................... 4-36
System Protection Control Register (SYPCR) ...................................................... 4-37
Software Service Register (SWSR) ....................................................................... 4-38
60x Bus Transfer Error Status and Control Register 1 (TESCR1) ........................ 4-39
60x Bus Transfer Error Status and Control Register 2 (TESCR2) ........................ 4-41
Local Bus Transfer Error Status and Control Register 1 (L_TESCR1)................. 4-42
Local Bus Transfer Error Status and Control Register 2 (L_TESCR2)................. 4-43
Time Counter Status and Control Register (TMCNTSC)...................................... 4-43
Time Counter Register (TMCNT) ......................................................................... 4-44
Time Counter Alarm Register (TMCNTAL) ......................................................... 4-45
Periodic Interrupt Registers ....................................................................................... 4-46
Periodic Interrupt Status and Control Register (PISCR) ....................................... 4-46
Periodic Interrupt Timer Count Register (PITC) ................................................... 4-47
Periodic Interrupt Timer Register (PITR).............................................................. 4-48
PCI Control Registers ................................................................................................ 4-48
PCI Base Register (PCIBRx)................................................................................. 4-49
PCI Mask Register (PCIMSKx) ............................................................................ 4-50
SIU Pin Multiplexing..................................................................................................... 4-50
Chapter 5
Reset
5.1
5.1.1
5.1.2
5.1.3
Reset Causes .................................................................................................................... 5-1
Reset Actions ............................................................................................................... 5-2
Power-On Reset Flow.................................................................................................. 5-2
HRESET Flow ............................................................................................................. 5-3
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
x
Freescale Semiconductor
Contents
Paragraph
Number
5.1.4
5.2
5.3
5.4
5.4.1
5.4.2
5.4.2.1
5.4.2.2
5.4.2.3
5.4.2.4
Title
Page
Number
SRESET Flow.............................................................................................................. 5-3
Reset Status Register (RSR) ............................................................................................ 5-4
Reset Mode Register (RMR) ........................................................................................... 5-5
Reset Configuration ......................................................................................................... 5-6
Hard Reset Configuration Word .................................................................................. 5-8
Hard Reset Configuration Examples ......................................................................... 5-10
Single MPC8280 with Default Configuration ....................................................... 5-10
Single MPC8280 Configured from Boot EPROM ................................................ 5-10
Multiple MPC8280s Configured from Boot EPROM ........................................... 5-11
Multiple MPC8280s in a System with No EPROM .............................................. 5-13
Part III
The Hardware Interface
Chapter 6
External Signals
6.1
6.2
Functional Pinout ............................................................................................................. 6-1
Signal Descriptions .......................................................................................................... 6-2
Chapter 7
60x Signals
7.1
7.2
7.2.1
7.2.1.1
7.2.1.1.1
7.2.1.1.2
7.2.1.2
7.2.1.2.1
7.2.1.2.2
7.2.1.3
7.2.1.3.1
7.2.1.3.2
7.2.2
7.2.2.1
7.2.2.1.1
7.2.2.2
7.2.3
7.2.3.1
Signal Configuration........................................................................................................ 7-2
Signal Descriptions .......................................................................................................... 7-2
Address Bus Arbitration Signals.................................................................................. 7-3
Bus Request (BR)—Output ..................................................................................... 7-3
Address Bus Request (BR)—Output ................................................................... 7-3
Address Bus Request (BR)—Input...................................................................... 7-3
Bus Grant (BG)........................................................................................................ 7-4
Bus Grant (BG)—Input ....................................................................................... 7-4
Bus Grant (BG)—Output..................................................................................... 7-4
Address Bus Busy (ABB)........................................................................................ 7-5
Address Bus Busy (ABB)—Output..................................................................... 7-5
Address Bus Busy (ABB)—Input ....................................................................... 7-5
Address Transfer Start Signal ...................................................................................... 7-5
Transfer Start (TS) ................................................................................................... 7-5
Transfer Start (TS)—Output ................................................................................ 7-5
Transfer Start (TS)—Input....................................................................................... 7-6
Address Transfer Signals ............................................................................................. 7-6
Address Bus (A[0–31])............................................................................................ 7-6
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
xi
Contents
Paragraph
Number
7.2.3.1.1
7.2.3.1.2
7.2.4
7.2.4.1
7.2.4.1.1
7.2.4.1.2
7.2.4.2
7.2.4.3
7.2.4.4
7.2.4.4.1
7.2.4.4.2
7.2.4.5
7.2.4.6
7.2.5
7.2.5.1
7.2.5.1.1
7.2.5.1.2
7.2.5.2
7.2.5.2.1
7.2.5.2.2
7.2.6
7.2.6.1
7.2.6.1.1
7.2.6.1.2
7.2.6.2
7.2.6.2.1
7.2.6.2.2
7.2.7
7.2.7.1
7.2.7.1.1
7.2.7.1.2
7.2.7.2
7.2.7.2.1
7.2.7.2.2
7.2.8
7.2.8.1
7.2.8.1.1
7.2.8.1.2
7.2.8.2
7.2.8.2.1
7.2.8.2.2
Title
Page
Number
Address Bus (A[0–31])—Output......................................................................... 7-6
Address Bus (A[0–31])—Input ........................................................................... 7-7
Address Transfer Attribute Signals.............................................................................. 7-7
Transfer Type (TT[0–4]).......................................................................................... 7-7
Transfer Type (TT[0–4])—Output....................................................................... 7-7
Transfer Type (TT[0–4])—Input ......................................................................... 7-7
Transfer Size (TSIZ[0–3]) ....................................................................................... 7-7
Transfer Burst (TBST)............................................................................................. 7-8
Global (GBL)........................................................................................................... 7-8
Global (GBL)—Output........................................................................................ 7-8
Global (GBL)—Input .......................................................................................... 7-8
Caching-Inhibited (CI)—Output ............................................................................. 7-9
Write-Through (WT)—Output ................................................................................ 7-9
Address Transfer Termination Signals......................................................................... 7-9
Address Acknowledge (AACK) .............................................................................. 7-9
Address Acknowledge (AACK)—Output........................................................... 7-9
Address Acknowledge (AACK)—Input ........................................................... 7-10
Address Retry (ARTRY)........................................................................................ 7-10
Address Retry (ARTRY)—Output .................................................................... 7-10
Address Retry (ARTRY)—Input ....................................................................... 7-10
Data Bus Arbitration Signals ..................................................................................... 7-11
Data Bus Grant (DBG) .......................................................................................... 7-11
Data Bus Grant (DBG)—Input.......................................................................... 7-11
Data Bus Grant (DBG)—Output ....................................................................... 7-11
Data Bus Busy (DBB) ........................................................................................... 7-12
Data Bus Busy (DBB)—Output ........................................................................ 7-12
Data Bus Busy (DBB)—Input ........................................................................... 7-12
Data Transfer Signals................................................................................................. 7-12
Data Bus (D[0–63]) ............................................................................................... 7-13
Data Bus (D[0–63])—Output ............................................................................ 7-13
Data Bus (D[0–63])—Input............................................................................... 7-13
Data Bus Parity (DP[0–7])..................................................................................... 7-13
Data Bus Parity (DP[0–7])—Output ................................................................. 7-14
Data Bus Parity (DP[0–7])—Input .................................................................... 7-14
Data Transfer Termination Signals ............................................................................ 7-14
Transfer Acknowledge (TA) .................................................................................. 7-14
Transfer Acknowledge (TA)—Input ................................................................. 7-15
Transfer Acknowledge (TA)—Output............................................................... 7-15
Transfer Error Acknowledge (TEA)...................................................................... 7-16
Transfer Error Acknowledge (TEA)—Input ..................................................... 7-16
Transfer Error Acknowledge (TEA)—Output................................................... 7-16
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
xii
Freescale Semiconductor
Contents
Paragraph
Number
7.2.8.3
7.2.8.3.1
7.2.8.3.2
Title
Page
Number
Partial Data Valid Indication (PSDVAL) ............................................................... 7-16
Partial Data Valid (PSDVAL)—Input................................................................ 7-17
Partial Data Valid (PSDVAL)—Output ............................................................. 7-17
Chapter 8
The 60x Bus
8.1
8.2
8.2.1
8.2.2
8.3
8.3.1
8.3.2
8.4
8.4.1
8.4.2
8.4.3
8.4.3.1
8.4.3.2
8.4.3.3
8.4.3.4
8.4.3.5
8.4.3.6
8.4.3.7
8.4.3.8
8.4.4
8.4.4.1
8.4.4.2
8.4.5
8.5
8.5.1
8.5.2
8.5.3
8.5.4
8.5.5
8.5.6
8.6
8.7
8.7.1
Terminology..................................................................................................................... 8-1
Bus Configuration............................................................................................................ 8-2
Single-MPC8280 Bus Mode........................................................................................ 8-2
60x-Compatible Bus Mode.......................................................................................... 8-3
60x Bus Protocol Overview ............................................................................................. 8-4
Arbitration Phase ......................................................................................................... 8-5
Address Pipelining and Split-Bus Transactions........................................................... 8-6
Address Tenure Operations.............................................................................................. 8-7
Address Arbitration...................................................................................................... 8-7
Address Pipelining....................................................................................................... 8-8
Address Transfer Attribute Signals.............................................................................. 8-9
Transfer Type Signal (TT[0–4]) Encoding .............................................................. 8-9
Transfer Code Signals TC[0–2] ............................................................................. 8-12
TBST and TSIZ[0–3] Signals and Size of Transfer .............................................. 8-12
Burst Ordering During Data Transfers .................................................................. 8-13
Effect of Alignment on Data Transfers.................................................................. 8-14
Effect of Port Size on Data Transfers .................................................................... 8-15
60x-Compatible Bus Mode—Size Calculation ..................................................... 8-17
Extended Transfer Mode ....................................................................................... 8-18
Address Transfer Termination ................................................................................... 8-21
Address Retried with ARTRY ............................................................................... 8-21
Address Tenure Timing Configuration .................................................................. 8-23
Pipeline Control ......................................................................................................... 8-23
Data Tenure Operations ................................................................................................. 8-24
Data Bus Arbitration.................................................................................................. 8-24
Data Streaming Mode ................................................................................................ 8-25
Data Bus Transfers and Normal Termination ............................................................ 8-25
Effect of ARTRY Assertion on Data Transfer and Arbitration ................................. 8-26
Port Size Data Bus Transfers and PSDVAL Termination.......................................... 8-26
Data Bus Termination by Assertion of TEA.............................................................. 8-28
Memory Coherency—MEI Protocol ............................................................................. 8-29
Processor State Signals .................................................................................................. 8-30
Support for the lwarx/stwcx. Instruction Pair ........................................................... 8-31
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
xiii
Contents
Paragraph
Number
8.7.2
8.8
Title
Page
Number
TLBISYNC Input ...................................................................................................... 8-31
Little-Endian Mode........................................................................................................ 8-31
Chapter 9
PCI Bridge
9.1
9.2
9.3
9.4
9.5
9.6
9.7
9.8
9.9
9.9.1
9.9.1.1
9.9.1.2
9.9.1.2.1
9.9.1.2.2
9.9.1.2.3
9.9.1.2.4
9.9.1.3
9.9.1.3.1
9.9.1.3.2
9.9.1.4
9.9.1.4.1
9.9.1.4.2
9.9.1.4.3
9.9.1.4.4
9.9.1.4.5
9.9.1.4.6
9.9.1.4.7
9.9.1.5
9.9.1.5.1
9.9.1.5.2
9.9.2
9.9.2.1
9.9.2.2
9.9.2.3
9.10
Signals.............................................................................................................................. 9-3
Clocking........................................................................................................................... 9-3
PCI Bridge Initialization.................................................................................................. 9-3
SDMA Interface............................................................................................................... 9-3
Interrupts from PCI Bridge .............................................................................................. 9-4
60x Bus Arbitration Priority ............................................................................................ 9-4
60x Bus Masters............................................................................................................... 9-4
CompactPCI Hot Swap Specification Support ................................................................ 9-5
PCI Interface .................................................................................................................... 9-5
PCI Interface Operation ............................................................................................... 9-6
Bus Commands........................................................................................................ 9-6
PCI Protocol Fundamentals ..................................................................................... 9-7
Basic Transfer Control......................................................................................... 9-8
Addressing ........................................................................................................... 9-8
Byte Enable Signals............................................................................................. 9-9
Bus Driving and Turnaround ............................................................................... 9-9
Bus Transactions...................................................................................................... 9-9
Read and Write Transactions ............................................................................... 9-9
Transaction Termination .................................................................................... 9-11
Other Bus Operations ............................................................................................ 9-13
Device Selection ................................................................................................ 9-13
Fast Back-to-Back Transactions ........................................................................ 9-14
Data Streaming .................................................................................................. 9-14
Host Mode Configuration Access...................................................................... 9-15
Agent Mode Configuration Access ................................................................... 9-16
Special Cycle Command ................................................................................... 9-16
Interrupt Acknowledge ...................................................................................... 9-17
Error Functions ...................................................................................................... 9-17
Parity.................................................................................................................. 9-17
Error Reporting.................................................................................................. 9-18
PCI Bus Arbitration ................................................................................................... 9-19
Bus Parking............................................................................................................ 9-19
Arbitration Algorithm............................................................................................ 9-19
Master Latency Timer............................................................................................ 9-20
Address Map .................................................................................................................. 9-21
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
xiv
Freescale Semiconductor
Contents
Paragraph
Number
9.10.1
9.10.2
9.10.2.1
9.10.2.2
9.10.3
9.11
9.11.1
9.11.1.1
9.11.1.2
9.11.1.3
9.11.1.4
9.11.1.5
9.11.1.6
9.11.1.7
9.11.1.8
9.11.1.9
9.11.1.10
9.11.1.11
9.11.1.12
9.11.1.13
9.11.1.14
9.11.1.15
9.11.1.16
9.11.1.17
9.11.2
9.11.2.1
9.11.2.2
9.11.2.3
9.11.2.4
9.11.2.5
9.11.2.6
9.11.2.7
9.11.2.8
9.11.2.9
9.11.2.10
9.11.2.11
9.11.2.12
9.11.2.13
9.11.2.14
9.11.2.15
Title
Page
Number
Address Map Programming ....................................................................................... 9-24
Address Translation ................................................................................................... 9-24
PCI Inbound Translation........................................................................................ 9-25
PCI Outbound Translation ..................................................................................... 9-26
SIU Registers ............................................................................................................. 9-26
Configuration Registers ................................................................................................. 9-27
Memory-Mapped Configuration Registers................................................................ 9-27
Message Unit (I2O) Registers................................................................................ 9-30
DMA Controller Registers..................................................................................... 9-30
PCI Outbound Translation Address Registers (POTARx) .................................... 9-30
PCI Outbound Base Address Registers (POBARx) .............................................. 9-31
PCI Outbound Comparison Mask Registers (POCMRx) ..................................... 9-32
Discard Timer Control Register (PTCR) .............................................................. 9-33
General Purpose Control Register (GPCR) .......................................................... 9-33
PCI General Control Register (PCI_GCR) ........................................................... 9-35
Error Status Register (ESR) .................................................................................. 9-35
Error Mask Register (EMR) ................................................................................. 9-37
Error Control Register (ECR) ............................................................................... 9-38
PCI Error Address Capture Register (PCI_EACR) .............................................. 9-39
PCI Error Data Capture Register (PCI_EDCR) .................................................... 9-40
PCI Error Control Capture Register (PCI_ECCR) ............................................... 9-40
PCI Inbound Translation Address Registers (PITARx) ........................................ 9-42
PCI Inbound Base Address Registers (PIBARx) .................................................. 9-42
PCI Inbound Comparison Mask Registers (PICMRx) .......................................... 9-43
PCI Bridge Configuration Registers ........................................................................ 9-45
Vendor ID Register ............................................................................................... 9-47
Device ID Register ............................................................................................... 9-47
PCI Bus Command Register ................................................................................. 9-47
PCI Bus Status Register ........................................................................................ 9-48
Revision ID Register ............................................................................................. 9-50
PCI Bus Programming Interface Register ............................................................ 9-50
Subclass Code Register ......................................................................................... 9-51
PCI Bus Base Class Code Register ....................................................................... 9-51
PCI Bus Cache Line Size Register ....................................................................... 9-52
PCI Bus Latency Timer Register .......................................................................... 9-52
Header Type Register ........................................................................................... 9-53
BIST Control Register .......................................................................................... 9-53
PCI Bus Internal Memory-Mapped Registers Base Address Register
(PIMMRBAR) .................................................................................................. 9-53
General Purpose Local Access Base Address Registers (GPLABARx) .............. 9-54
Subsystem Vendor ID Register ............................................................................. 9-55
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
xv
Contents
Paragraph
Number
9.11.2.16
9.11.2.17
9.11.2.18
9.11.2.19
9.11.2.20
9.11.2.21
9.11.2.22
9.11.2.23
9.11.2.24
9.11.2.25
9.11.2.26
9.11.2.27
9.11.2.27.1
9.11.2.27.2
9.11.2.28
9.12
9.12.1
9.12.1.1
9.12.1.2
9.12.2
9.12.2.1
9.12.2.2
9.12.3
9.12.3.1
9.12.3.2
9.12.3.2.1
9.12.3.2.2
9.12.3.3
9.12.3.3.1
9.12.3.3.2
9.12.3.4
9.12.3.4.1
9.12.3.4.2
9.12.3.4.3
9.12.3.4.4
9.12.3.4.5
9.12.3.4.6
Title
Page
Number
Subsystem Device ID Register ............................................................................. 9-56
PCI Bus Capabilities Pointer Register .................................................................. 9-56
PCI Bus Interrupt Line Register ........................................................................... 9-57
PCI Bus Interrupt Pin Register ............................................................................. 9-57
PCI Bus MIN GNT ............................................................................................... 9-58
PCI Bus MAX LAT .............................................................................................. 9-58
PCI Bus Function Register ................................................................................... 9-59
PCI Bus Arbiter Configuration Register ............................................................... 9-60
PCI Hot Swap Register Block .............................................................................. 9-61
PCI Hot Swap Control Status Register ................................................................. 9-61
PCI Configuration Register Access from the Core ............................................... 9-62
PCI Configuration Register Access in Big-Endian Mode .................................... 9-62
Additional Information on Endianess ............................................................... 9-63
Notes on GPCR[LE_MODE] ........................................................................... 9-63
Initializing the PCI Configuration Registers ........................................................ 9-64
Message Unit (I2O) ....................................................................................................... 9-66
Message Registers...................................................................................................... 9-66
Inbound Message Registers (IMRx) ..................................................................... 9-67
Outbound Message Registers (OMRx) ................................................................. 9-67
Door Bell Registers ................................................................................................... 9-68
Outbound Doorbell Register (ODR) ..................................................................... 9-68
Inbound Doorbell Register (IDR) ......................................................................... 9-69
I2O Unit .................................................................................................................... 9-70
PCI Configuration Identification .......................................................................... 9-71
Inbound FIFOs ...................................................................................................... 9-71
Inbound Free_FIFO Head Pointer Register (IFHPR) and Inbound
Free_FIFO Tail Pointer Register (IFTPR) .................................................... 9-72
Inbound Post_FIFO Head Pointer Register (IPHPR) and Inbound
Post_FIFO Tail Pointer Register (IPTPR) .................................................... 9-73
Outbound FIFOs ................................................................................................... 9-75
Outbound Free_FIFO Head Pointer Register (OFHPR) and Outbound
Free_FIFO Tail Pointer Register (OFTPR) .................................................. 9-75
Outbound Post_FIFO Head Pointer Register (OPHPR) and Outbound
Post_FIFO Tail Pointer Register (OPTPR) ................................................... 9-76
I2O Registers.......................................................................................................... 9-78
Inbound FIFO Queue Port Register (IFQPR) ................................................... 9-78
Outbound FIFO Queue Port Register (OFQPR) ............................................... 9-79
Outbound Message Interrupt Status Register (OMISR) ................................... 9-80
Outbound Message Interrupt Mask Register (OMIMR) .................................. 9-81
Inbound Message Interrupt Status Register (IMISR) ....................................... 9-82
Inbound Message Interrupt Mask Register (IMIMR) ....................................... 9-83
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
xvi
Freescale Semiconductor
Contents
Paragraph
Number
9.12.3.4.7
9.12.3.4.8
9.13
9.13.1
9.13.1.1
9.13.1.2
9.13.1.3
9.13.1.4
9.13.1.5
9.13.1.6
9.13.1.6.1
9.13.1.6.2
9.13.1.6.3
9.13.1.6.4
9.13.1.6.5
9.13.1.6.6
9.13.1.6.7
9.13.2
9.13.2.1
9.13.2.2
9.14
9.14.1
9.14.1.1
9.14.1.1.1
9.14.1.1.2
9.14.1.1.3
9.14.1.2
9.14.1.3
9.14.1.3.1
9.14.1.3.2
9.14.1.3.3
9.14.1.3.4
9.14.1.3.5
9.14.1.4
9.14.1.4.1
9.14.1.4.2
9.14.1.4.3
Title
Page
Number
Messaging Unit Control Register (MUCR) ...................................................... 9-84
Queue Base Address Register (QBAR) ............................................................ 9-85
DMA Controller............................................................................................................. 9-86
DMA Operation ......................................................................................................... 9-86
DMA Direct Mode................................................................................................. 9-87
DMA Chaining Mode ............................................................................................ 9-87
DMA Coherency.................................................................................................... 9-88
Halt and Error Conditions...................................................................................... 9-88
DMA Transfer Types ............................................................................................. 9-88
DMA Registers ...................................................................................................... 9-89
DMA Mode Registers 0–3 (DMAMRx) .......................................................... 9-89
DMA Status Registers 0–3 (DMASRx) ............................................................ 9-91
DMA Current Descriptor Address Registers 0–3 (DMACDARx) ................... 9-92
DMA Source Address Registers 0–3 (DMASARx) ......................................... 9-93
DMA Destination Address Registers 0–3 (DMADARx) ................................. 9-94
DMA Byte Count Registers 0–3 (DMABCRx) ................................................ 9-94
DMA Next Descriptor Address Registers 0–3 (DMANDARx) ....................... 9-95
DMA Segment Descriptors........................................................................................ 9-96
Descriptor in Big-Endian Mode............................................................................. 9-97
Descriptor in Little-Endian Mode.......................................................................... 9-98
Error Handling ............................................................................................................... 9-98
Interrupt and Error Signals ........................................................................................ 9-99
PCI Bus Error Signals............................................................................................ 9-99
System Error (SERR) ........................................................................................ 9-99
Parity Error (PERR)........................................................................................... 9-99
Error Reporting.................................................................................................. 9-99
Illegal Register Access Error ................................................................................. 9-99
PCI Interface........................................................................................................ 9-100
Address Parity Error ........................................................................................ 9-100
Data Parity Error.............................................................................................. 9-100
Master-Abort Transaction Termination ........................................................... 9-100
Target-Abort Error ........................................................................................... 9-101
NMI ................................................................................................................. 9-101
Embedded Utilities .............................................................................................. 9-101
Outbound Free Queue Overflow ..................................................................... 9-101
Inbound Post Queue Overflow ........................................................................ 9-101
Inbound DoorBell Machine Check.................................................................. 9-101
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
xvii
Contents
Paragraph
Number
Title
Page
Number
Chapter 10
Clocks and Power Control
10.1
10.1.1
10.1.2
10.1.3
10.1.4
10.1.5
10.1.6
10.1.7
10.2
10.3
10.4
10.5
10.5.1
10.6
MPC8280 Clock Block Diagram ................................................................................... 10-1
Main PLL................................................................................................................... 10-1
Core PLL.................................................................................................................... 10-2
Skew Elimination....................................................................................................... 10-2
Dividers...................................................................................................................... 10-2
Internal Clock Signals................................................................................................ 10-2
PCI Bridge as an Agent Operating from the PCI System Clock ............................... 10-4
PCI Bridge as a Host Generating the PCI System Clock .......................................... 10-4
External Clock Inputs .................................................................................................... 10-5
PLL Pins ....................................................................................................................... 10-5
System Clock Control Register (SCCR)........................................................................ 10-6
System Clock Mode Register (SCMR).......................................................................... 10-7
Core PLL Configurations........................................................................................... 10-8
Clock Configuration Modes........................................................................................... 10-9
Chapter 11
Memory Controller
11.1
11.2
11.2.1
11.2.2
11.2.3
11.2.4
11.2.5
11.2.6
11.2.7
11.2.8
11.2.9
11.2.10
11.2.11
11.2.12
11.2.13
11.2.14
11.3
11.3.1
11.3.2
11.3.3
Features .......................................................................................................................... 11-3
Basic Architecture.......................................................................................................... 11-4
Address and Address Space Checking....................................................................... 11-7
Page Hit Checking ..................................................................................................... 11-8
Error Checking and Correction (ECC) ...................................................................... 11-8
Parity Generation and Checking ................................................................................ 11-8
Transfer Error Acknowledge (TEA) Generation ....................................................... 11-8
Machine Check Interrupt (MCP) Generation ............................................................ 11-9
Data Buffer Controls (BCTLx and LWR) ................................................................. 11-9
Atomic Bus Operation ............................................................................................... 11-9
Data Pipelining ......................................................................................................... 11-9
External Memory Controller Support ...................................................................... 11-10
External Address Latch Enable Signal (ALE) ......................................................... 11-10
ECC/Parity Byte Select (PBSE) .............................................................................. 11-10
Partial Data Valid Indication (PSDVAL) ..................................................................11-11
BADDR[27:31] Signal Connections ....................................................................... 11-12
Register Descriptions ................................................................................................... 11-12
Base Registers (BRx) ............................................................................................... 11-13
Option Registers (ORx) ........................................................................................... 11-15
60x SDRAM Mode Register (PSDMR) .................................................................. 11-20
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
xviii
Freescale Semiconductor
Contents
Paragraph
Number
11.3.4
11.3.5
11.3.6
11.3.7
11.3.8
11.3.9
11.3.10
11.3.11
11.3.12
11.3.13
11.3.14
11.4
11.4.1
11.4.2
11.4.3
11.4.4
11.4.5
11.4.5.1
11.4.5.2
11.4.6
11.4.6.1
11.4.6.2
11.4.6.3
11.4.6.4
11.4.6.5
11.4.6.6
11.4.6.7
11.4.6.8
11.4.7
11.4.8
11.4.9
11.4.10
11.4.11
11.4.12
11.4.12.1
11.4.13
11.5
11.5.1
11.5.1.1
11.5.1.2
11.5.1.3
Title
Page
Number
Local Bus SDRAM Mode Register (LSDMR)........................................................ 11-24
Machine A/B/C Mode Registers (MxMR)............................................................... 11-26
Memory Data Register (MDR) ................................................................................ 11-28
Memory Address Register (MAR) .......................................................................... 11-29
60x Bus-Assigned UPM Refresh Timer (PURT)..................................................... 11-30
Local Bus-Assigned UPM Refresh Timer (LURT) ................................................. 11-30
60x Bus-Assigned SDRAM Refresh Timer (PSRT)................................................ 11-31
Local Bus-Assigned SDRAM Refresh Timer (LSRT) ............................................ 11-32
Memory Refresh Timer Prescaler Register (MPTPR) ............................................. 11-32
60x Bus Error Status and Control Registers (TESCRx) .......................................... 11-33
Local Bus Error Status and Control Registers (L_TESCRx) .................................. 11-33
SDRAM Machine ........................................................................................................ 11-33
Supported SDRAM Configurations......................................................................... 11-35
SDRAM Power-On Initialization ............................................................................ 11-35
JEDEC-Standard SDRAM Interface Commands .................................................... 11-35
Page-Mode Support and Pipeline Accesses............................................................. 11-36
Bank Interleaving .................................................................................................... 11-36
Using BNKSEL Signals in Single-MPC8280 Bus Mode.................................... 11-37
SDRAM Address Multiplexing (SDAM and BSMA)......................................... 11-37
SDRAM Device-Specific Parameters...................................................................... 11-38
Precharge-to-Activate Interval............................................................................. 11-39
Activate to Read/Write Interval ........................................................................... 11-39
Column Address to First Data Out—CAS Latency............................................. 11-40
Last Data Out to Precharge.................................................................................. 11-41
Last Data In to Precharge—Write Recovery ....................................................... 11-41
Refresh Recovery Interval (RFRC) ..................................................................... 11-42
External Address Multiplexing Signal................................................................. 11-42
External Address and Command Buffers (BUFCMD)........................................ 11-42
SDRAM Interface Timing ....................................................................................... 11-43
SDRAM Read/Write Transactions........................................................................... 11-46
SDRAM Mode-Set Command Timing .................................................................... 11-47
SDRAM Refresh...................................................................................................... 11-47
SDRAM Refresh Timing ......................................................................................... 11-48
SDRAM Configuration Examples ........................................................................... 11-48
SDRAM Configuration Example (Page-Based Interleaving).............................. 11-49
SDRAM Configuration Example (Bank-Based Interleaving) ................................. 11-50
General-Purpose Chip-Select Machine (GPCM)......................................................... 11-52
Timing Configuration .............................................................................................. 11-53
Chip-Select Assertion Timing ............................................................................. 11-54
Chip-Select and Write Enable Deassertion Timing ............................................. 11-55
Relaxed Timing.................................................................................................... 11-56
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
xix
Contents
Paragraph
Number
11.5.1.4
11.5.1.5
11.5.1.6
11.5.2
11.5.3
11.5.4
11.6
11.6.1
11.6.1.1
11.6.1.2
11.6.1.3
11.6.1.4
11.6.2
11.6.3
11.6.4
11.6.4.1
11.6.4.1.1
11.6.4.1.2
11.6.4.1.3
11.6.4.1.4
11.6.4.1.5
11.6.4.2
11.6.4.3
11.6.4.4
11.6.4.5
11.6.4.6
11.6.5
11.6.6
11.7
11.7.0.1
11.8
11.8.1
11.8.2
11.9
11.9.1
11.9.2
11.9.3
11.9.4
11.9.5
11.9.5.1
Title
Page
Number
Output Enable (OE) Timing ................................................................................ 11-58
Programmable Wait State Configuration ............................................................. 11-59
Extended Hold Time on Read Accesses .............................................................. 11-59
External Access Termination ................................................................................... 11-61
Boot Chip-Select Operation..................................................................................... 11-62
Differences Between the MPC8xx GPCM and MPC82xx GPCM .......................... 11-63
User-Programmable Machines (UPMs)....................................................................... 11-63
Requests ................................................................................................................... 11-65
Memory Access Requests.................................................................................... 11-66
UPM Refresh Timer Requests ............................................................................. 11-66
Software Requests—run Command .................................................................... 11-67
Exception Requests.............................................................................................. 11-67
Programming the UPMs .......................................................................................... 11-67
Clock Timing ........................................................................................................... 11-68
The RAM Array....................................................................................................... 11-70
RAM Words......................................................................................................... 11-71
Chip-Select Signals (CxTx) ............................................................................. 11-75
Byte-Select Signals (BxTx) ............................................................................. 11-76
General-Purpose Signals (GxTx, GOx) ........................................................... 11-77
Loop Control.................................................................................................... 11-77
Repeat Execution of Current RAM Word (REDO) ........................................ 11-77
Address Multiplexing .......................................................................................... 11-78
Data Valid and Data Sample Control................................................................... 11-78
Signals Negation.................................................................................................. 11-79
The Wait Mechanism ........................................................................................... 11-79
Extended Hold Time on Read Accesses ............................................................. 11-80
UPM DRAM Configuration Example ..................................................................... 11-80
Differences Between the MPC8xx UPM and MPC82xx UPM ............................... 11-81
Memory System Interface Example Using UPM ........................................................ 11-82
EDO Interface Example....................................................................................... 11-93
Handling Devices with Slow or Variable Access Times............................................ 11-101
Hierarchical Bus Interface Example ...................................................................... 11-101
Slow Devices Example .......................................................................................... 11-101
External Master Support (60x-Compatible Mode) .................................................... 11-101
60x-Compatible External Masters (non-MPC8280).............................................. 11-102
MPC8280 External Masters................................................................................... 11-102
Extended Controls in 60x-Compatible Mode ........................................................ 11-102
Address Incrementing for External Bursting Masters ........................................... 11-102
External Masters Timing........................................................................................ 11-103
Example of External Master Using the SDRAM Machine ............................... 11-105
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
xx
Freescale Semiconductor
Contents
Paragraph
Number
Title
Page
Number
Chapter 12
Secondary (L2) Cache Support
12.1
12.1.1
12.1.2
12.1.3
12.2
12.3
12.4
12.5
L2 Cache Configurations ............................................................................................... 12-1
Copy-Back Mode....................................................................................................... 12-1
Write-Through Mode ................................................................................................. 12-2
ECC/Parity Mode....................................................................................................... 12-4
L2 Cache Interface Parameters ...................................................................................... 12-6
System Requirements When Using the L2 Cache Interface.......................................... 12-7
L2 Cache Operation ....................................................................................................... 12-7
Timing Example............................................................................................................. 12-7
Chapter 13
IEEE 1149.1 Test Access Port
13.1
13.2
13.3
13.4
13.5
13.6
Overview........................................................................................................................ 13-1
TAP Controller............................................................................................................... 13-2
Boundary Scan Register................................................................................................. 13-3
Instruction Register........................................................................................................ 13-5
MPC8280 Restrictions ................................................................................................... 13-7
Nonscan Chain Operation .............................................................................................. 13-7
Part IV
Communications Processor Module
Chapter 14
Communications Processor Module Overview
14.1
14.2
14.3
14.3.1
14.3.2
14.3.3
14.3.4
14.3.5
14.3.6
14.3.7
14.3.8
14.3.9
14.3.10
Features .......................................................................................................................... 14-1
Serial Configurations ..................................................................................................... 14-3
Communications Processor (CP) ................................................................................... 14-4
CPM Performance Evaluation ................................................................................... 14-4
Features...................................................................................................................... 14-4
CP Block Diagram ..................................................................................................... 14-5
G2_LE Core Interface................................................................................................ 14-7
Peripheral Interface.................................................................................................... 14-7
Execution from RAM ................................................................................................ 14-8
RISC Controller Configuration Register (RCCR) ..................................................... 14-9
RISC Time-Stamp Control Register (RTSCR) ........................................................ 14-10
RISC Time-Stamp Register (RTSR) ........................................................................ 14-11
RISC Microcode Revision Number......................................................................... 14-11
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
xxi
Contents
Paragraph
Number
14.4
14.4.1
14.4.1.1
14.4.2
14.4.3
14.5
14.5.1
14.5.2
14.6
14.6.1
14.6.2
14.6.3
14.6.4
14.6.5
14.6.6
14.6.7
14.6.8
14.6.9
14.6.10
Title
Page
Number
Command Set............................................................................................................... 14-12
CP Command Register (CPCR)............................................................................... 14-12
CP Commands ..................................................................................................... 14-14
Command Register Example ................................................................................... 14-17
Command Execution Latency.................................................................................. 14-17
Dual-Port RAM............................................................................................................ 14-17
Buffer Descriptors (BDs)......................................................................................... 14-21
Parameter RAM ....................................................................................................... 14-21
RISC Timer Tables....................................................................................................... 14-23
RISC Timer Table Parameter RAM......................................................................... 14-23
RISC Timer Command Register (TM_CMD) ......................................................... 14-25
RISC Timer Table Entries........................................................................................ 14-25
RISC Timer Event Register (RTER)/Mask Register (RTMR) ................................ 14-25
set timer Command.................................................................................................. 14-26
RISC Timer Initialization Sequence ........................................................................ 14-26
RISC Timer Initialization Example ......................................................................... 14-27
RISC Timer Interrupt Handling ............................................................................... 14-27
RISC Timer Table Scan Algorithm.......................................................................... 14-27
Using the RISC Timers to Track CP Loading ......................................................... 14-28
Chapter 15
Serial Interface with Time-Slot Assigner
15.1
15.2
15.3
15.4
15.4.1
15.4.2
15.4.3
15.4.4
15.4.5
15.5
15.5.1
15.5.2
15.5.3
15.5.4
15.5.5
15.6
15.6.1
15.6.2
Features .......................................................................................................................... 15-3
Overview........................................................................................................................ 15-4
Enabling Connections to TSA ....................................................................................... 15-7
Serial Interface RAM..................................................................................................... 15-8
One Multiplexed Channel with Static Frames ........................................................... 15-9
One Multiplexed Channel with Dynamic Frames ..................................................... 15-9
Programming SIx RAM Entries .............................................................................. 15-10
SIx RAM Programming Example............................................................................ 15-14
Static and Dynamic Routing .................................................................................... 15-15
Serial Interface Registers ............................................................................................. 15-17
SI Global Mode Registers (SIxGMR) ..................................................................... 15-17
SI Mode Registers (SIxMR) .................................................................................... 15-17
SIx RAM Shadow Address Registers (SIxRSR) ..................................................... 15-24
SI Command Register (SIxCMDR)......................................................................... 15-24
SI Status Registers (SIxSTR)................................................................................... 15-25
Serial Interface IDL Interface Support ........................................................................ 15-25
IDL Interface Example ............................................................................................ 15-26
IDL Interface Programming..................................................................................... 15-29
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
xxii
Freescale Semiconductor
Contents
Paragraph
Number
15.7
15.7.1
15.7.2
15.7.2.1
15.7.2.2
Title
Page
Number
Serial Interface GCI Support ....................................................................................... 15-30
SI GCI Activation/Deactivation Procedure ............................................................. 15-32
Serial Interface GCI Programming .......................................................................... 15-32
Normal Mode GCI Programming........................................................................ 15-32
SCIT Programming.............................................................................................. 15-33
Chapter 16
CPM Multiplexing
16.1
16.2
16.3
16.4
16.4.1
16.4.2
16.4.3
16.4.4
16.4.5
16.4.6
Features .......................................................................................................................... 16-2
Enabling Connections to TSA or NMSI ........................................................................ 16-3
NMSI Configuration ...................................................................................................... 16-4
CMX Registers .............................................................................................................. 16-7
CMX UTOPIA Address Register (CMXUAR) ......................................................... 16-7
CMX SI1 Clock Route Register (CMXSI1CR)....................................................... 16-12
CMX SI2 Clock Route Register (CMXSI2CR)....................................................... 16-13
CMX FCC Clock Route Register (CMXFCR) ........................................................ 16-13
CMX SCC Clock Route Register (CMXSCR) ........................................................ 16-16
CMX SMC Clock Route Register (CMXSMR) ...................................................... 16-19
Chapter 17
Baud-Rate Generators (BRGs)
17.1
17.2
17.3
BRG Configuration Registers 1–8 (BRGCx) ................................................................ 17-2
Autobaud Operation on a UART ................................................................................... 17-4
UART Baud Rate Examples .......................................................................................... 17-5
Chapter 18
Timers
18.1
18.2
18.2.1
18.2.2
18.2.3
18.2.4
18.2.5
18.2.6
18.2.7
Features .......................................................................................................................... 18-1
General-Purpose Timer Units ........................................................................................ 18-2
Cascaded Mode.......................................................................................................... 18-3
Timer Global Configuration Registers (TGCR1 and TGCR2).................................. 18-3
Timer Mode Registers (TMR1–TMR4)..................................................................... 18-5
Timer Reference Registers (TRR1–TRR4) ............................................................... 18-6
Timer Capture Registers (TCR1–TCR4) ................................................................... 18-7
Timer Counters (TCN1–TCN4)................................................................................. 18-7
Timer Event Registers (TER1–TER4)....................................................................... 18-7
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
xxiii
Contents
Paragraph
Number
Title
Page
Number
Chapter 19
SDMA Channels and IDMA Emulation
19.1
19.2
19.2.1
19.2.2
19.2.3
19.2.4
19.3
19.4
19.5
19.5.1
19.5.1.1
19.5.1.2
19.5.1.3
19.5.2
19.5.2.1
19.5.2.1.1
19.5.2.1.2
19.5.2.2
19.5.2.2.1
19.5.2.2.2
19.5.3
19.5.4
19.6
19.7
19.7.1
19.7.1.1
19.7.1.2
19.7.2
19.8
19.8.1
19.8.2
19.8.2.1
19.8.2.2
19.8.2.3
19.8.3
19.8.4
19.8.5
19.9
SDMA Bus Arbitration and Bus Transfers .................................................................... 19-2
SDMA Registers ............................................................................................................ 19-3
SDMA Status Register (SDSR) ................................................................................. 19-3
SDMA Mask Register (SDMR)................................................................................. 19-4
SDMA Transfer Error Address Registers (PDTEA and LDTEA)............................. 19-4
SDMA Transfer Error MSNUM Registers (PDTEM and LDTEM) ......................... 19-4
IDMA Emulation ........................................................................................................... 19-5
IDMA Features .............................................................................................................. 19-5
IDMA Transfers............................................................................................................. 19-6
Memory-to-Memory Transfers .................................................................................. 19-6
External Request Mode.......................................................................................... 19-8
Normal Mode......................................................................................................... 19-9
Working with a PCI Bus ........................................................................................ 19-9
Memory to/from Peripheral Transfers ....................................................................... 19-9
Dual-Address Transfers ....................................................................................... 19-10
Peripheral to Memory ...................................................................................... 19-10
Memory to Peripheral ...................................................................................... 19-10
Single Address (Fly-By) Transfers ...................................................................... 19-10
Peripheral-to-Memory Fly-By Transfers ......................................................... 19-11
Memory-to-Peripheral Fly-By Transfers ......................................................... 19-11
Controlling 60x Bus Bandwidth .............................................................................. 19-11
PCI Burst Length and Latency Control ................................................................... 19-12
IDMA Priorities ........................................................................................................... 19-12
IDMA Interface Signals............................................................................................... 19-13
DREQx and DACKx ............................................................................................... 19-13
Level-Sensitive Mode.......................................................................................... 19-14
Edge-Sensitive Mode........................................................................................... 19-14
DONEx .................................................................................................................... 19-14
IDMA Operation.......................................................................................................... 19-14
Auto Buffer and Buffer Chaining ............................................................................ 19-15
IDMAx Parameter RAM ......................................................................................... 19-16
DMA Channel Mode (DCM)............................................................................... 19-18
Data Transfer Types as Programmed in DCM..................................................... 19-20
Programming DTS and STS ................................................................................ 19-20
IDMA Performance ................................................................................................. 19-22
IDMA Event Register (IDSR) and Mask Register (IDMR) .................................... 19-22
IDMA BDs............................................................................................................... 19-23
IDMA Commands........................................................................................................ 19-26
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
xxiv
Freescale Semiconductor
Contents
Paragraph
Number
19.9.1
19.9.2
19.10
19.10.1
19.11
19.12
19.12.1
19.12.2
19.12.3
Title
Page
Number
start_idma Command............................................................................................... 19-26
stop_idma Command ............................................................................................... 19-26
IDMA Bus Exceptions................................................................................................. 19-27
Externally Recognizing IDMA Operand Transfers ................................................. 19-27
Programming the Parallel I/O Registers ...................................................................... 19-28
IDMA Programming Examples ................................................................................... 19-29
Peripheral-to-Memory Mode (60x Bus to Local Bus)—IDMA2 ............................ 19-29
Memory-to-Peripheral Fly-By Mode—IDMA3 ...................................................... 19-30
Memory-to-Memory (PCI Bus to 60x Bus)—IDMA1 ............................................ 19-32
Chapter 20
Serial Communications Controllers (SCCs)
20.1
20.1.1
20.1.2
20.1.3
20.1.4
20.2
20.3
20.3.1
20.3.2
20.3.3
20.3.4
20.3.5
20.3.5.1
20.3.5.2
20.3.6
20.3.6.1
20.3.7
20.3.7.1
20.3.7.2
20.3.7.3
20.3.7.4
20.3.7.5
20.3.8
Features .......................................................................................................................... 20-2
The General SCC Mode Registers (GSMR1–GSMR4) ............................................ 20-3
Protocol-Specific Mode Register (PSMR) ................................................................ 20-9
Data Synchronization Register (DSR)....................................................................... 20-9
Transmit-on-Demand Register (TODR) .................................................................. 20-10
SCC Buffer Descriptors (BDs) .................................................................................... 20-10
SCC Parameter RAM................................................................................................... 20-13
SCC Base Addresses................................................................................................ 20-14
Function Code Registers (RFCR and TFCR) .......................................................... 20-15
Handling SCC Interrupts ......................................................................................... 20-16
Initializing the SCCs................................................................................................ 20-16
Controlling SCC Timing with RTS, CTS, and CD.................................................. 20-17
Synchronous Protocols ........................................................................................ 20-17
Asynchronous Protocols ...................................................................................... 20-20
Digital Phase-Locked Loop (DPLL) Operation....................................................... 20-21
Encoding Data with a DPLL................................................................................ 20-23
Reconfiguring the SCCs .......................................................................................... 20-24
General Reconfiguration Sequence for an SCC Transmitter............................... 20-24
Reset Sequence for an SCC Transmitter.............................................................. 20-25
General Reconfiguration Sequence for an SCC Receiver ................................... 20-25
Reset Sequence for an SCC Receiver.................................................................. 20-25
Switching Protocols ............................................................................................. 20-25
Saving Power ........................................................................................................... 20-25
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
xxv
Contents
Paragraph
Number
Title
Page
Number
Chapter 21
SCC UART Mode
21.1
21.2
21.3
21.4
21.5
21.6
21.7
21.8
21.9
21.10
21.11
21.12
21.13
21.14
21.15
21.16
21.17
21.18
21.19
21.20
21.21
21.22
Features .......................................................................................................................... 21-2
Normal Asynchronous Mode......................................................................................... 21-2
Synchronous Mode ........................................................................................................ 21-3
SCC UART Parameter RAM ......................................................................................... 21-3
Data-Handling Methods: Character- or Message-Based ............................................... 21-5
Error and Status Reporting............................................................................................. 21-5
SCC UART Commands ................................................................................................. 21-6
Multidrop Systems and Address Recognition ............................................................... 21-7
Receiving Control Characters ........................................................................................ 21-7
Hunt Mode (Receiver) ................................................................................................... 21-9
Inserting Control Characters into the Transmit Data Stream......................................... 21-9
Sending a Break (Transmitter)..................................................................................... 21-10
Sending a Preamble (Transmitter) ............................................................................... 21-10
Fractional Stop Bits (Transmitter) ............................................................................... 21-11
Handling Errors in the SCC UART Controller ............................................................ 21-12
UART Mode Register (PSMR).................................................................................... 21-13
SCC UART Receive Buffer Descriptor (RxBD) ......................................................... 21-15
SCC UART Transmit Buffer Descriptor (TxBD) ........................................................ 21-18
SCC UART Event Register (SCCE) and Mask Register (SCCM) .............................. 21-19
SCC UART Status Register (SCCS)............................................................................ 21-21
SCC UART Programming Example ............................................................................ 21-22
S-Records Loader Application..................................................................................... 21-23
Chapter 22
SCC HDLC Mode
22.1
22.2
22.3
22.4
22.5
22.6
22.7
22.8
22.9
22.10
22.11
22.12
SCC HDLC Features ..................................................................................................... 22-1
SCC HDLC Channel Frame Transmission .................................................................... 22-2
SCC HDLC Channel Frame Reception ......................................................................... 22-2
SCC HDLC Parameter RAM......................................................................................... 22-3
Programming the SCC in HDLC Mode......................................................................... 22-5
SCC HDLC Commands................................................................................................. 22-5
Handling Errors in the SCC HDLC Controller.............................................................. 22-6
HDLC Mode Register (PSMR)...................................................................................... 22-7
SCC HDLC Receive Buffer Descriptor (RxBD) ........................................................... 22-8
SCC HDLC Transmit Buffer Descriptor (TxBD)........................................................ 22-12
HDLC Event Register (SCCE)/HDLC Mask Register (SCCM) ................................. 22-13
SCC HDLC Status Register (SCCS)............................................................................ 22-15
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
xxvi
Freescale Semiconductor
Contents
Paragraph
Number
22.13
22.13.1
22.13.2
22.14
22.14.1
22.14.2
22.14.3
22.14.4
22.14.5
22.14.6
22.14.6.1
22.14.6.2
Title
Page
Number
SCC HDLC Programming Examples .......................................................................... 22-16
SCC HDLC Programming Example #1................................................................... 22-16
SCC HDLC Programming Example #2................................................................... 22-18
HDLC Bus Mode with Collision Detection................................................................. 22-18
HDLC Bus Features................................................................................................. 22-20
Accessing the HDLC Bus ........................................................................................ 22-20
Increasing Performance ........................................................................................... 22-21
Delayed RTS Mode.................................................................................................. 22-22
Using the Time-Slot Assigner (TSA) ...................................................................... 22-23
HDLC Bus Protocol Programming.......................................................................... 22-23
Programming GSMR and PSMR for the HDLC Bus Protocol ........................... 22-23
HDLC Bus Controller Programming Example.................................................... 22-24
Chapter 23
SCC BISYNC Mode
23.1
23.2
23.3
23.4
23.5
23.6
23.7
23.8
23.9
23.10
23.11
23.12
23.13
23.14
23.15
23.16
23.17
Features .......................................................................................................................... 23-2
SCC BISYNC Channel Frame Transmission ................................................................ 23-2
SCC BISYNC Channel Frame Reception ..................................................................... 23-3
SCC BISYNC Parameter RAM ..................................................................................... 23-3
SCC BISYNC Commands ............................................................................................. 23-4
SCC BISYNC Control Character Recognition.............................................................. 23-5
BISYNC SYNC Register (BSYNC).............................................................................. 23-7
SCC BISYNC DLE Register (BDLE) ........................................................................... 23-8
Sending and Receiving the Synchronization Sequence ................................................. 23-9
Handling Errors in the SCC BISYNC ........................................................................... 23-9
BISYNC Mode Register (PSMR)................................................................................ 23-10
SCC BISYNC Receive BD (RxBD) ............................................................................ 23-12
SCC BISYNC Transmit BD (TxBD)........................................................................... 23-14
BISYNC Event Register (SCCE)/BISYNC Mask Register (SCCM).......................... 23-15
SCC Status Registers (SCCS)...................................................................................... 23-16
Programming the SCC BISYNC Controller ................................................................ 23-17
SCC BISYNC Programming Example ........................................................................ 23-18
Chapter 24
SCC Transparent Mode
24.1
24.2
24.3
24.4
Features .......................................................................................................................... 24-1
SCC Transparent Channel Frame Transmission Process............................................... 24-2
SCC Transparent Channel Frame Reception Process .................................................... 24-2
Achieving Synchronization in Transparent Mode ......................................................... 24-3
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
xxvii
Contents
Paragraph
Number
24.4.1
24.4.1.1
24.4.1.2
24.4.1.2.1
24.4.1.3
24.4.2
24.4.2.1
24.4.2.2
24.4.3
24.5
24.6
24.7
24.8
24.9
24.10
24.11
24.12
24.13
24.14
Title
Page
Number
Synchronization in NMSI Mode................................................................................ 24-3
In-Line Synchronization Pattern............................................................................ 24-3
External Synchronization Signals.......................................................................... 24-3
External Synchronization Example ................................................................... 24-4
Transparent Mode without Explicit Synchronization............................................ 24-5
Synchronization and the TSA .................................................................................... 24-5
Inline Synchronization Pattern .............................................................................. 24-5
Inherent Synchronization....................................................................................... 24-5
End of Frame Detection............................................................................................. 24-5
CRC Calculation in Transparent Mode.......................................................................... 24-6
SCC Transparent Parameter RAM................................................................................. 24-6
SCC Transparent Commands......................................................................................... 24-6
Handling Errors in the Transparent Controller .............................................................. 24-7
Transparent Mode and the PSMR.................................................................................. 24-8
SCC Transparent Receive Buffer Descriptor (RxBD) ................................................... 24-8
SCC Transparent Transmit Buffer Descriptor (TxBD)................................................ 24-10
SCC Transparent Event Register (SCCE)/Mask Register (SCCM)............................. 24-11
SCC Status Register in Transparent Mode (SCCS) ..................................................... 24-12
SCC2 Transparent Programming Example.................................................................. 24-13
Chapter 25
SCC Ethernet Mode
25.1
25.2
25.3
25.4
25.5
25.6
25.7
25.8
25.9
25.10
25.11
25.12
25.13
25.14
25.15
25.16
25.17
25.18
Ethernet on the MPC8280.............................................................................................. 25-1
Features .......................................................................................................................... 25-2
Connecting the MPC8280 to Ethernet ........................................................................... 25-4
SCC Ethernet Channel Frame Transmission ................................................................. 25-5
SCC Ethernet Channel Frame Reception....................................................................... 25-6
The Content-Addressable Memory (CAM) Interface.................................................... 25-6
SCC Ethernet Parameter RAM ...................................................................................... 25-7
Programming the Ethernet Controller............................................................................ 25-9
SCC Ethernet Commands .............................................................................................. 25-9
SCC Ethernet Address Recognition............................................................................. 25-11
Hash Table Algorithm.................................................................................................. 25-12
Interpacket Gap Time................................................................................................... 25-12
Handling Collisions ..................................................................................................... 25-12
Internal and External Loopback................................................................................... 25-13
Full-Duplex Ethernet Support...................................................................................... 25-13
Handling Errors in the Ethernet Controller.................................................................. 25-13
Ethernet Mode Register (PSMR) ................................................................................. 25-14
SCC Ethernet Receive BD ........................................................................................... 25-16
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
xxviii
Freescale Semiconductor
Contents
Paragraph
Number
25.19
25.20
25.21
Title
Page
Number
SCC Ethernet Transmit Buffer Descriptor................................................................... 25-18
SCC Ethernet Event Register (SCCE)/Mask Register (SCCM) .................................. 25-20
SCC Ethernet Programming Example ......................................................................... 25-22
Chapter 26
SCC AppleTalk Mode
26.1
26.2
26.3
26.4
26.4.1
26.4.2
26.4.3
26.4.4
Operating the LocalTalk Bus ......................................................................................... 26-1
Features .......................................................................................................................... 26-2
Connecting to AppleTalk ............................................................................................... 26-2
Programming the SCC in AppleTalk Mode................................................................... 26-3
Programming the GSMR ........................................................................................... 26-3
Programming the PSMR............................................................................................ 26-4
Programming the TODR............................................................................................ 26-4
SCC AppleTalk Programming Example.................................................................... 26-4
Chapter 27
Universal Serial Bus Controller
27.1
27.2
27.2.1
27.3
27.3.1
27.4
27.4.1
27.5
27.5.1
27.5.1.1
27.5.1.2
27.5.2
27.5.3
27.5.4
27.5.5
27.5.6
27.5.7
27.5.7.1
27.5.7.2
27.5.7.3
27.5.7.4
27.5.7.5
USB Integration in the MPC8280.................................................................................. 27-1
Overview........................................................................................................................ 27-1
USB Controller Key Features .................................................................................... 27-2
Host Controller Limitations ........................................................................................... 27-2
USB Controller Pin Functions and Clocking............................................................. 27-2
USB Function Description............................................................................................. 27-4
USB Function Controller Transmit/Receive.............................................................. 27-5
USB Host Description ................................................................................................... 27-7
USB Host Controller Transmit/Receive .................................................................... 27-8
Packet-Level Interface ........................................................................................... 27-9
Transaction-Level Interface ................................................................................... 27-9
SOF Transmission for USB Host Controller ........................................................... 27-12
USB Function and Host Parameter RAM Memory Map......................................... 27-12
Endpoint Parameters Block Pointer (EPxPTR) ....................................................... 27-13
Frame Number (FRAME_N)................................................................................... 27-15
USB Function Code Registers (RFCR and TFCR) ................................................. 27-16
USB Function Programming Model ........................................................................ 27-17
USB Mode Register (USMOD)........................................................................... 27-17
USB Slave Address Register (USADR) .............................................................. 27-18
USB Endpoint Registers (USEP1–USEP4)......................................................... 27-18
USB Command Register (USCOM).................................................................... 27-20
USB Event Register (USBER) ............................................................................ 27-20
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
xxix
Contents
Paragraph
Number
27.5.7.6
27.5.7.7
27.5.7.8
27.6
27.6.1
27.6.2
27.6.3
27.6.4
27.7
27.7.1
27.7.2
27.8
27.9
27.10
27.10.1
27.11
27.11.1
Title
Page
Number
USB Mask Register (USBMR)............................................................................ 27-21
USB Status Register (USBS)............................................................................... 27-21
USB Start of Frame Timer (USSFT) ................................................................... 27-22
USB Buffer Descriptor Ring........................................................................................ 27-22
USB Receive Buffer Descriptor (Rx BD) for Host and Function ........................... 27-24
USB Transmit Buffer Descriptor (Tx BD) for Function.......................................... 27-26
USB Transmit Buffer Descriptor (Tx BD) for Host ................................................ 27-27
USB Transaction Buffer Descriptor (TrBD) for Host.............................................. 27-29
USB CP Commands..................................................................................................... 27-32
STOP Tx Command................................................................................................. 27-32
RESTART Tx Command ......................................................................................... 27-33
USB Controller Errors ................................................................................................. 27-33
USB Function Controller Initialization Example ........................................................ 27-34
Programming the USB Host Controller (Packet-Level) .............................................. 27-35
USB Host Controller Initialization Example ........................................................... 27-35
Programming the USB Host Controller (Transaction-Level) ...................................... 27-37
USB Host Controller Initialization Example ........................................................... 27-37
Chapter 28
Serial Management Controllers (SMCs)
28.1
28.2
28.2.1
28.2.2
28.2.3
28.2.3.1
28.2.4
28.2.4.1
28.2.4.2
28.2.4.3
28.2.4.4
28.2.4.5
28.2.5
28.2.6
28.3
28.3.1
28.3.2
28.3.3
28.3.4
28.3.5
Features .......................................................................................................................... 28-2
Common SMC Settings and Configurations ................................................................. 28-2
SMC Mode Registers (SMCMR1/SMCMR2)........................................................... 28-2
SMC Buffer Descriptor Operation............................................................................. 28-4
SMC Parameter RAM................................................................................................ 28-5
SMC Function Code Registers (RFCR/TFCR) ..................................................... 28-8
Disabling SMCs On-the-Fly ...................................................................................... 28-8
SMC Transmitter Full Sequence............................................................................ 28-9
SMC Transmitter Shortcut Sequence .................................................................... 28-9
SMC Receiver Full Sequence................................................................................ 28-9
SMC Receiver Shortcut Sequence......................................................................... 28-9
Switching Protocols ............................................................................................... 28-9
Saving Power ........................................................................................................... 28-10
Handling Interrupts in the SMC............................................................................... 28-10
SMC in UART Mode ................................................................................................... 28-10
Features.................................................................................................................... 28-11
SMC UART Channel Transmission Process ........................................................... 28-11
SMC UART Channel Reception Process................................................................. 28-11
Programming the SMC UART Controller ............................................................... 28-11
SMC UART Transmit and Receive Commands ...................................................... 28-12
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
xxx
Freescale Semiconductor
Contents
Paragraph
Number
28.3.6
28.3.7
28.3.8
28.3.9
28.3.10
28.3.11
28.3.12
28.4
28.4.1
28.4.2
28.4.3
28.4.4
28.4.5
28.4.6
28.4.7
28.4.8
28.4.9
28.4.10
28.4.11
28.5
28.5.1
28.5.2
28.5.2.1
28.5.2.2
28.5.3
28.5.3.1
28.5.3.2
28.5.4
28.5.5
28.5.6
28.5.7
28.5.8
28.5.9
Title
Page
Number
Sending a Break ....................................................................................................... 28-12
Sending a Preamble ................................................................................................. 28-13
Handling Errors in the SMC UART Controller ....................................................... 28-13
SMC UART RxBD .................................................................................................. 28-14
SMC UART TxBD .................................................................................................. 28-17
SMC UART Event Register (SMCE)/Mask Register (SMCM) .............................. 28-18
SMC UART Controller Programming Example...................................................... 28-19
SMC in Transparent Mode........................................................................................... 28-20
Features.................................................................................................................... 28-20
SMC Transparent Channel Transmission Process ................................................... 28-21
SMC Transparent Channel Reception Process ........................................................ 28-21
Using SMSYN for Synchronization ........................................................................ 28-22
Using the Time-Slot Assigner (TSA) for Synchronization...................................... 28-23
SMC Transparent Commands.................................................................................. 28-25
Handling Errors in the SMC Transparent Controller............................................... 28-25
SMC Transparent RxBD.......................................................................................... 28-26
SMC Transparent TxBD .......................................................................................... 28-27
SMC Transparent Event Register (SMCE)/Mask Register (SMCM)...................... 28-28
SMC Transparent NMSI Programming Example.................................................... 28-29
The SMC in GCI Mode ............................................................................................... 28-30
SMC GCI Parameter RAM...................................................................................... 28-30
Handling the GCI Monitor Channel ........................................................................ 28-31
SMC GCI Monitor Channel Transmission Process ............................................. 28-31
SMC GCI Monitor Channel Reception Process .................................................. 28-31
Handling the GCI C/I Channel ................................................................................ 28-31
SMC GCI C/I Channel Transmission Process ..................................................... 28-31
SMC GCI C/I Channel Reception Process .......................................................... 28-32
SMC GCI Commands.............................................................................................. 28-32
SMC GCI Monitor Channel RxBD ......................................................................... 28-32
SMC GCI Monitor Channel TxBD.......................................................................... 28-33
SMC GCI C/I Channel RxBD ................................................................................. 28-33
SMC GCI C/I Channel TxBD.................................................................................. 28-34
SMC GCI Event Register (SMCE)/Mask Register (SMCM).................................. 28-34
Chapter 29
Multi-Channel Controllers (MCCs)
29.1
29.1.1
29.2
29.3
MCC Operation Overview............................................................................................. 29-2
MCC Data Structure Organization............................................................................. 29-2
Global MCC Parameters ................................................................................................ 29-4
Channel-Specific Parameters ......................................................................................... 29-5
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
xxxi
Contents
Paragraph
Number
29.3.1
29.3.1.1
29.3.1.2
29.3.1.3
29.3.1.4
29.3.2
29.3.2.1
29.3.2.2
29.3.2.3
29.3.2.4
29.3.3
29.3.3.1
29.3.3.1.1
29.3.3.2
29.3.4
29.3.4.1
29.3.4.2
29.3.4.2.1
29.3.4.3
29.3.4.3.1
29.3.4.3.2
29.3.4.3.3
29.3.4.4
29.3.4.4.1
29.3.4.4.2
29.3.4.4.3
29.3.4.4.4
29.3.4.5
29.4
29.5
29.5.1
29.5.2
29.5.3
29.5.4
29.6
29.7
29.8
29.8.1
29.8.1.1
29.8.1.2
Title
Page
Number
Channel-Specific HDLC Parameters ......................................................................... 29-5
Internal Transmitter State (TSTATE)—HDLC Mode ........................................... 29-7
Interrupt Mask (INTMSK)—HDLC Mode ........................................................... 29-8
Channel Mode Register (CHAMR)—HDLC Mode.............................................. 29-8
Internal Receiver State (RSTATE)—HDLC Mode ............................................. 29-10
Channel-Specific Transparent Parameters ............................................................... 29-11
Internal Transmitter State (TSTATE)—Transparent Mode ................................. 29-12
Interrupt Mask (INTMSK)—Transparent Mode ................................................. 29-12
Channel Mode Register (CHAMR)—Transparent Mode.................................... 29-12
Internal Receiver State (RSTATE)—Transparent Mode ..................................... 29-14
MCC Parameters for AAL1 CES Usage.................................................................. 29-14
Channel-Specific Parameters—AAL1 CES ........................................................ 29-14
Interrupt Circular Table Entry and Interrupt Mask
(INTMSK) —AAL1 CES............................................................................ 29-15
Channel Mode Register (CHAMR)—AAL1 CES .............................................. 29-15
Channel-Specific SS7 Parameters ........................................................................... 29-17
Extended Channel Mode Register (ECHAMR)—SS7 Mode.............................. 29-20
Signal Unit Error Monitor (SUERM)—SS7 Mode ............................................. 29-22
SUERM in Japanese SS7................................................................................. 29-23
SS7 Configuration Register—SS7 Mode ............................................................ 29-23
AERM Implementation ................................................................................... 29-24
AERM in Japanese SS7................................................................................... 29-24
Disabling SUERM ........................................................................................... 29-25
SU Filtering—SS7 Mode..................................................................................... 29-25
Comparison Mask............................................................................................ 29-25
Comparison State Machine.............................................................................. 29-25
Filtering Limitations ........................................................................................ 29-26
Resetting the SU Filtering Mechanism............................................................ 29-26
Octet Counting Mode—SS7 Mode...................................................................... 29-27
Channel Extra Parameters............................................................................................ 29-27
Superchannels .............................................................................................................. 29-28
Superchannel Table.................................................................................................. 29-28
Superchannels and Receiving .................................................................................. 29-29
Transparent Slot Synchronization............................................................................ 29-29
Superchannelling Programming Examples.............................................................. 29-29
MCC Configuration Registers (MCCFx) .................................................................... 29-32
MCC Commands ......................................................................................................... 29-33
MCC Exceptions.......................................................................................................... 29-34
MCC Event Register (MCCE)/Mask Register (MCCM) ........................................ 29-36
Interrupt Circular Table Entry ............................................................................. 29-37
Global Transmitter Underrun (GUN) .................................................................. 29-38
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
xxxii
Freescale Semiconductor
Contents
Paragraph
Number
29.8.1.2.1
29.8.1.2.2
29.8.1.2.3
29.8.1.2.4
29.8.1.2.5
29.8.1.2.6
29.8.1.2.7
29.8.1.3
29.8.1.4
29.9
29.9.1
29.9.2
29.10
29.10.1
29.10.2
29.11
Title
Page
Number
TDM Clock...................................................................................................... 29-39
Synchronization Pulse ..................................................................................... 29-39
SIRAM Programming...................................................................................... 29-39
MCC Initialization........................................................................................... 29-40
CPM Bandwidth .............................................................................................. 29-40
CPM Priority.................................................................................................... 29-40
Bus Latency ..................................................................................................... 29-41
Recovery from GUN Errors................................................................................. 29-41
Global Overrun (GOV)........................................................................................ 29-41
MCC Buffer Descriptors.............................................................................................. 29-41
Receive Buffer Descriptor (RxBD) ......................................................................... 29-42
Transmit Buffer Descriptor (TxBD) ........................................................................ 29-44
MCC Initialization and Start/Stop Sequence ............................................................... 29-46
Stopping and Restarting a Single-Channel .............................................................. 29-47
Stopping and Restarting a Superchannel ................................................................. 29-47
MCC Latency and Performance .................................................................................. 29-48
Chapter 30
Fast Communications Controllers (FCCs)
30.1
30.2
30.2.1
30.3
30.4
30.5
30.6
30.7
30.7.1
30.8
30.8.1
30.8.2
30.8.3
30.9
30.10
30.10.1
30.10.1.1
30.10.1.2
30.10.1.3
30.11
30.12
Overview........................................................................................................................ 30-1
General FCC Mode Registers (GFMRx) ....................................................................... 30-3
General FCC Expansion Mode Register (GFEMR) .................................................. 30-7
FCC Protocol-Specific Mode Registers (FPSMRx) ...................................................... 30-8
FCC Data Synchronization Registers (FDSRx)............................................................. 30-8
FCC Transmit-on-Demand Registers (FTODRx).......................................................... 30-9
FCC Buffer Descriptors ............................................................................................... 30-10
FCC Parameter RAM................................................................................................... 30-12
FCC Function Code Registers (FCRx) .................................................................... 30-14
Interrupts from the FCCs ............................................................................................. 30-14
FCC Event Registers (FCCEx) ................................................................................ 30-15
FCC Mask Registers (FCCMx) ............................................................................... 30-15
FCC Status Registers (FCCSx)................................................................................ 30-15
FCC Initialization ........................................................................................................ 30-15
FCC Interrupt Handling ............................................................................................... 30-16
FCC Transmit Errors................................................................................................ 30-16
Re-Initialization Procedure.................................................................................. 30-17
Recovery Sequence.............................................................................................. 30-17
Adjusting Transmitter BD Handling.................................................................... 30-17
FCC Timing Control .................................................................................................... 30-17
Disabling the FCCs On-the-Fly ................................................................................... 30-20
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
xxxiii
Contents
Paragraph
Number
30.12.1
30.12.2
30.12.3
30.12.4
30.12.5
30.13
Title
Page
Number
FCC Transmitter Full Sequence............................................................................... 30-21
FCC Transmitter Shortcut Sequence ....................................................................... 30-21
FCC Receiver Full Sequence................................................................................... 30-21
FCC Receiver Shortcut Sequence............................................................................ 30-21
Switching Protocols ................................................................................................. 30-22
Saving Power ............................................................................................................... 30-22
Chapter 31
ATM Controller and
AAL0, AAL1, and AAL5
31.1
31.2
31.2.1
31.2.1.1
31.2.1.2
31.2.1.2.1
31.2.1.3
31.2.1.4
31.2.1.5
31.2.2
31.2.2.1
31.2.2.2
31.2.2.2.1
31.2.2.3
31.2.2.4
31.2.3
31.2.4
31.3
31.3.1
31.3.2
31.3.3
31.3.3.1
31.3.3.2
31.3.4
31.3.5
31.3.5.1
31.3.5.2
31.3.5.3
31.3.5.3.1
31.3.5.3.2
Features .......................................................................................................................... 31-1
ATM Controller Overview............................................................................................. 31-5
Transmitter Overview ................................................................................................ 31-5
AAL5 Transmitter Overview................................................................................. 31-5
AAL1 Transmitter Overview................................................................................. 31-5
AAL1 CES Transmitter Overview .................................................................... 31-6
AAL0 Transmitter Overview................................................................................. 31-6
AAL2 Transmitter Overview................................................................................. 31-6
Transmit External Rate and Internal Rate Modes.................................................. 31-6
Receiver Overview .................................................................................................... 31-6
AAL5 Receiver Overview ..................................................................................... 31-7
AAL1 Receiver Overview ..................................................................................... 31-7
AAL1 CES Receiver Overview......................................................................... 31-8
AAL0 Receiver Overview ..................................................................................... 31-8
AAL2 Receiver Overview ..................................................................................... 31-8
Performance Monitoring............................................................................................ 31-8
ABR Flow Control..................................................................................................... 31-8
ATM Pace Control (APC) Unit...................................................................................... 31-8
APC Modes and ATM Service Types ........................................................................ 31-8
APC Unit Scheduling Mechanism ............................................................................. 31-9
Determining the Scheduling Table Size................................................................... 31-10
Determining the Cells Per Slot (CPS) in a Scheduling Table.............................. 31-10
Determining the Number of Slots in a Scheduling Table .................................... 31-10
Determining the Time-Slot Scheduling Rate of a Channel ..................................... 31-11
ATM Traffic Type .................................................................................................... 31-11
Peak Cell Rate Traffic Type................................................................................. 31-11
Determining the PCR Traffic Type Parameters ................................................... 31-11
Peak and Sustain Traffic Type (VBR) ................................................................. 31-12
Example for Using VBR Traffic Parameters ................................................... 31-12
Handling the Cell Loss Priority (CLP)—VBR Type 1 and 2 .......................... 31-13
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
xxxiv
Freescale Semiconductor
Contents
Paragraph
Number
31.3.5.4
31.3.6
31.4
31.4.1
31.4.2
31.4.2.1
31.4.2.2
31.4.3
31.4.4
31.5
31.5.1
31.5.1.1
31.5.1.2
31.5.1.3
31.5.2
31.5.2.1
31.5.3
31.6
31.6.1
31.6.2
31.6.3
31.6.4
31.6.5
31.6.6
31.6.6.1
31.6.6.2
31.6.6.3
31.6.6.4
31.7
31.7.1
31.8
31.9
31.9.1
31.9.2
31.9.3
31.9.4
31.9.5
31.9.6
31.9.7
31.9.8
31.10
Title
Page
Number
Peak and Minimum Cell Rate Traffic Type (UBR+)........................................... 31-13
Determining the Priority of an ATM Channel ......................................................... 31-13
VCI/VPI Address Lookup Mechanism........................................................................ 31-13
External CAM Lookup ............................................................................................ 31-14
Address Compression .............................................................................................. 31-15
VP-Level Address Compression Table (VPLT) .................................................. 31-16
VC-Level Address Compression Tables (VCLTs)............................................... 31-17
Misinserted Cells ..................................................................................................... 31-18
Receive Raw Cell Queue ......................................................................................... 31-18
Available Bit Rate (ABR) Flow Control...................................................................... 31-19
The ABR Model....................................................................................................... 31-20
ABR Flow Control Source End-System Behavior .............................................. 31-20
ABR Flow Control Destination End-System Behavior ....................................... 31-21
ABR Flowcharts .................................................................................................. 31-21
RM Cell Structure.................................................................................................... 31-26
RM Cell Rate Representation .............................................................................. 31-26
ABR Flow Control Setup......................................................................................... 31-27
OAM Support .............................................................................................................. 31-27
ATM-Layer OAM Definitions ................................................................................. 31-27
Virtual Path (F4) Flow Mechanism ......................................................................... 31-28
Virtual Channel (F5) Flow Mechanism ................................................................... 31-28
Receiving OAM F4 or F5 Cells............................................................................... 31-28
Transmitting OAM F4 or F5 Cells........................................................................... 31-28
Performance Monitoring.......................................................................................... 31-29
Running a Performance Block Test ..................................................................... 31-30
PM Block Monitoring.......................................................................................... 31-30
PM Block Generation .......................................................................................... 31-31
BRC Performance Calculations........................................................................... 31-32
User-Defined Cells (UDC) .......................................................................................... 31-32
UDC Extended Address Mode (UEAD).................................................................. 31-32
ATM Layer Statistics ................................................................................................... 31-33
ATM-to-TDM Interworking ........................................................................................ 31-33
Automatic Data Forwarding .................................................................................... 31-33
Using Interrupts in Automatic Data Forwarding ..................................................... 31-34
Timing Issues ........................................................................................................... 31-35
Clock Synchronization (SRTS and Adaptive FIFOs) .............................................. 31-35
Mapping TDM Time Slots to VCs........................................................................... 31-35
CAS Support ............................................................................................................ 31-35
Trunk Condition....................................................................................................... 31-36
ATM-to-ATM Data Forwarding............................................................................... 31-36
ATM Memory Structure............................................................................................... 31-36
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
xxxv
Contents
Paragraph
Number
31.10.1
31.10.1.1
31.10.1.2
31.10.1.3
31.10.2
31.10.2.1
31.10.2.2
31.10.2.2.1
31.10.2.2.2
31.10.2.2.3
31.10.2.2.4
31.10.2.2.5
31.10.2.2.6
31.10.2.3
31.10.2.3.1
31.10.2.3.2
31.10.2.3.3
31.10.2.3.4
31.10.2.3.5
31.10.2.3.6
31.10.2.3.7
31.10.2.3.8
31.10.3
31.10.4
31.10.4.1
31.10.4.2
31.10.4.3
31.10.5
31.10.5.1
31.10.5.2
31.10.5.2.1
31.10.5.2.2
31.10.5.2.3
31.10.5.2.4
31.10.5.3
31.10.5.4
31.10.5.5
31.10.5.6
31.10.5.7
31.10.5.8
31.10.5.9
Title
Page
Number
Parameter RAM ....................................................................................................... 31-36
Determining UEAD_OFFSET (UEAD Mode Only) .......................................... 31-39
VCI Filtering (VCIF) ........................................................................................... 31-39
Global Mode Entry (GMODE)............................................................................ 31-40
Connection Tables (RCT, TCT, and TCTE) ............................................................ 31-41
ATM Channel Code ............................................................................................. 31-41
Receive Connection Table (RCT)........................................................................ 31-43
AAL5 Protocol-Specific RCT ......................................................................... 31-46
AAL5-ABR Protocol-Specific RCT................................................................ 31-47
AAL1 Protocol-Specific RCT ......................................................................... 31-47
AAL0 Protocol-Specific RCT ......................................................................... 31-49
AAL1 CES Protocol-Specific RCT ................................................................. 31-50
AAL2 Protocol-Specific RCT ......................................................................... 31-50
Transmit Connection Table (TCT)....................................................................... 31-50
AAL5 Protocol-Specific TCT ......................................................................... 31-53
AAL1 Protocol-Specific TCT ......................................................................... 31-54
AAL0 Protocol-Specific TCT ......................................................................... 31-55
AAL1 CES Protocol-Specific TCT ................................................................. 31-55
AAL2 Protocol-Specific TCT ......................................................................... 31-55
VBR Protocol-Specific TCTE ......................................................................... 31-56
UBR+ Protocol-Specific TCTE....................................................................... 31-57
ABR Protocol-Specific TCTE ......................................................................... 31-57
OAM Performance Monitoring Tables .................................................................... 31-60
APC Data Structure ................................................................................................. 31-61
APC Parameter Tables ......................................................................................... 31-62
APC Priority Table .............................................................................................. 31-63
APC Scheduling Tables ....................................................................................... 31-63
ATM Controller Buffer Descriptors (BDs) .............................................................. 31-64
Transmit Buffer Operation................................................................................... 31-64
Receive Buffer Operation .................................................................................... 31-65
Static Buffer Allocation ................................................................................... 31-65
Global Buffer Allocation ................................................................................. 31-66
Free Buffer Pools............................................................................................. 31-67
Free Buffer Pool Parameter Tables.................................................................. 31-68
ATM Controller Buffers....................................................................................... 31-69
AAL5 RxBD........................................................................................................ 31-69
AAL1 RxBD........................................................................................................ 31-71
AAL0 RxBD........................................................................................................ 31-72
AAL1 CES RxBD................................................................................................ 31-73
AAL2 RxBD........................................................................................................ 31-73
AAL5, AAL1 CES User-Defined Cell—RxBD Extension ................................. 31-73
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
xxxvi
Freescale Semiconductor
Contents
Paragraph
Number
31.10.5.10
31.10.5.11
31.10.5.12
31.10.5.13
31.10.5.14
31.10.5.15
31.10.6
31.10.7
31.11
31.11.1
31.11.2
31.11.3
31.12
31.12.1
31.12.1.1
31.12.2
31.12.2.1
31.12.2.2
31.12.2.3
31.12.3
31.13
31.13.1
31.13.2
31.13.3
31.14
31.15
31.15.1
31.15.1.1
31.15.1.2
31.15.1.3
31.15.1.4
31.15.1.5
31.15.1.6
31.16
31.17
31.17.1
31.17.2
31.17.3
Title
Page
Number
AAL5 TxBDs....................................................................................................... 31-74
AAL1 TxBDs....................................................................................................... 31-75
AAL0 TxBDs....................................................................................................... 31-76
AAL1 CES TxBDs .............................................................................................. 31-77
AAL2 TxBDs....................................................................................................... 31-77
AAL5, AAL1 User-Defined Cell—TxBD Extension.......................................... 31-77
AAL1 Sequence Number (SN) Protection Table..................................................... 31-77
UNI Statistics Table ................................................................................................. 31-78
ATM Exceptions .......................................................................................................... 31-79
Interrupt Queues ...................................................................................................... 31-79
Interrupt Queue Entry .............................................................................................. 31-80
Interrupt Queue Parameter Tables ........................................................................... 31-80
The UTOPIA Interface ................................................................................................ 31-81
UTOPIA Interface Master Mode ............................................................................. 31-81
UTOPIA Master Multiple PHY Operation.......................................................... 31-82
UTOPIA Interface Slave Mode ............................................................................... 31-83
UTOPIA Slave Multiple PHY Operation ............................................................ 31-84
UTOPIA Clocking Modes ................................................................................... 31-84
UTOPIA Loop-Back Modes................................................................................ 31-84
Extended Number of PHYs ..................................................................................... 31-85
ATM Registers ............................................................................................................. 31-85
General FCC Mode Register (GFMR)..................................................................... 31-85
FCC Protocol-Specific Mode Register (FPSMR).................................................... 31-85
ATM Event Register (FCCE)/Mask Register (FCCM)............................................ 31-88
ATM Transmit Command ............................................................................................ 31-89
Transmission Rate Modes—External, Internal, and Expanded Internal...................... 31-90
FCC Transmit Internal Rate Mode .......................................................................... 31-91
FCC Transmit Internal Rate Register (FTIRRx) ................................................. 31-91
Example ............................................................................................................... 31-92
Internal Rate Programming Model ...................................................................... 31-93
FCC Transmit Internal Rate Port Enable Registers (FIRPERx).......................... 31-93
FCC Internal Rate Event Registers (FIRERx) ..................................................... 31-94
FCC Internal Rate Selection Registers (FIRSRx_HI, FIRSRx_LO) ................... 31-95
SRTS Generation and Clock Recovery Using External Logic .................................... 31-97
Configuring the ATM Controller for Maximum CPM Performance........................... 31-98
Using Transmit Internal Rate Mode ........................................................................ 31-98
APC Configuration .................................................................................................. 31-99
Buffer Configuration................................................................................................ 31-99
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
xxxvii
Contents
Paragraph
Number
Title
Page
Number
Chapter 32
ATM AAL1 Circuit Emulation Service
32.1
32.2
32.2.1
32.2.2
32.3
32.4
32.4.1
32.4.1.1
32.4.1.2
32.4.2
32.4.3
32.4.4
32.4.5
32.4.6
32.4.7
32.4.7.1
32.4.7.2
32.4.7.2.1
32.4.7.3
32.4.7.3.1
32.5
32.5.1
32.6
32.6.1
32.7
32.8
32.8.1
32.9
32.9.1
32.9.1.1
32.9.2
32.9.2.1
32.10
32.11
32.11.1
32.11.2
32.12
32.12.1
Features .......................................................................................................................... 32-1
AAL1 CES Transmitter Overview................................................................................. 32-3
Data Path.................................................................................................................... 32-3
Signaling Path ............................................................................................................ 32-3
AAL1 CES Receiver Overview ..................................................................................... 32-4
Interworking Functions.................................................................................................. 32-6
Automatic Data Forwarding ...................................................................................... 32-6
ATM-to-TDM ........................................................................................................ 32-7
TDM-to-ATM ........................................................................................................ 32-7
Timing Issues ............................................................................................................. 32-8
Clock Synchronization (SRTS, Adaptive FIFO) ....................................................... 32-9
Mapping TDM Time Slots to VCs............................................................................. 32-9
Trunk Condition....................................................................................................... 32-10
Channel Associated Signaling (CAS) Support ........................................................ 32-10
Mapping VC Signaling to CAS Blocks ................................................................... 32-11
CAS Routing Table.............................................................................................. 32-12
TDM-to-ATM CAS Support................................................................................ 32-13
CAS Mapping Using the Core (Optional) ....................................................... 32-14
ATM-to-TDM CAS Support................................................................................ 32-14
CAS Updates Using the Core (Optional) ........................................................ 32-15
ATM-to-TDM Adaptive Slip Control .......................................................................... 32-15
CES Adaptive Threshold Tables.............................................................................. 32-16
3-Step-SN Algorithm ................................................................................................... 32-20
The Three States of the Algorithm .......................................................................... 32-20
Pointer Verification Mechanism .................................................................................. 32-21
AAL-1 Memory Structure............................................................................................ 32-22
AAL1 CES Parameter RAM.................................................................................... 32-22
Receive and Transmit Connection Tables (RCT, TCT) ............................................... 32-25
Receive Connection Table (RCT)............................................................................ 32-26
AAL1 CES Protocol-Specific RCT ..................................................................... 32-29
Transmit Connection Table (TCT)........................................................................... 32-32
AAL1 CES Protocol-Specific TCT ..................................................................... 32-34
Outgoing CAS Status Register (OCASSR) ................................................................ 32-36
Buffer Descriptors........................................................................................................ 32-36
Transmit Buffer Operation....................................................................................... 32-36
Receive Buffer Operation ........................................................................................ 32-37
ATM Controller Buffers............................................................................................... 32-38
AAL1 CES RxBD.................................................................................................... 32-39
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
xxxviii
Freescale Semiconductor
Contents
Paragraph
Number
32.12.2
32.13
32.13.1
32.14
32.15
32.16
32.17
32.18
Title
Page
Number
AAL1 CES TxBDs .................................................................................................. 32-40
AAL1 CES Exceptions ................................................................................................ 32-41
AAL1 CES Interrupt Queue Entry........................................................................... 32-41
AAL1 Sequence Number (SN) Protection Table ........................................................ 32-42
Internal AAL1 CES Statistics Tables........................................................................... 32-43
External AAL1 CES Statistics Tables.......................................................................... 32-44
CES-Specific Additions to the MCC ........................................................................... 32-44
Application Considerations.......................................................................................... 32-44
Chapter 33
ATM AAL2
33.1
33.2
33.3
33.3.1
33.3.2
33.3.2.1
33.3.2.2
33.3.3
33.3.4
33.3.5
33.3.5.1
33.3.5.2
33.3.5.3
33.3.5.4
33.3.5.5
33.4
33.4.1
33.4.2
33.4.3
33.4.4
33.4.4.1
33.4.4.2
33.4.4.3
33.4.4.4
33.4.4.5
33.4.4.6
33.4.4.7
33.4.4.8
33.5
Introduction.................................................................................................................... 33-1
Features .......................................................................................................................... 33-3
AAL2 Transmitter.......................................................................................................... 33-5
Transmitter Overview ................................................................................................ 33-5
Transmit Priority Mechanism .................................................................................... 33-6
Round Robin Priority............................................................................................. 33-6
Fixed Priority ......................................................................................................... 33-7
Partial Fill Mode (PFM) ............................................................................................ 33-7
No STF Mode ............................................................................................................ 33-8
AAL2 Tx Data Structures .......................................................................................... 33-9
AAL2 Protocol-Specific TCT................................................................................ 33-9
CPS Tx Queue Descriptor ................................................................................... 33-12
CPS Buffer Structure ........................................................................................... 33-14
SSSAR Tx Queue Descriptor .............................................................................. 33-16
SSSAR Transmit Buffer Descriptor..................................................................... 33-18
AAL2 Receiver ............................................................................................................ 33-19
Receiver Overview .................................................................................................. 33-19
Mapping of PHY | VP | VC | CID............................................................................ 33-20
AAL2 Switching...................................................................................................... 33-21
AAL2 RX Data Structures ....................................................................................... 33-22
AAL2 Protocol-Specific RCT ............................................................................. 33-23
CID Mapping Tables and RxQDs........................................................................ 33-26
CPS Rx Queue Descriptors.................................................................................. 33-26
CPS Receive Buffer Descriptor (RxBD) ............................................................. 33-27
CPS Switch Rx Queue Descriptor ....................................................................... 33-28
SWITCH Receive/Transmit Buffer Descriptor (RxBD)...................................... 33-29
SSSAR Rx Queue Descriptor .............................................................................. 33-30
SSSAR Receive Buffer Descriptor ...................................................................... 33-32
AAL2 Parameter RAM ................................................................................................ 33-34
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
xxxix
Contents
Paragraph
Number
33.6
33.7
Title
Page
Number
User-Defined Cells in AAL2 ....................................................................................... 33-37
AAL2 Exceptions ........................................................................................................ 33-38
Chapter 34
Inverse Multiplexing for ATM (IMA)
34.1
34.1.1
34.1.2
34.1.3
34.1.4
34.1.5
34.1.6
34.2
34.2.1
34.2.2
34.2.3
34.2.3.1
34.2.3.2
34.3
34.3.1
34.3.1.1
34.3.1.2
34.3.2
34.3.2.1
34.3.2.1.1
34.3.2.2
34.3.2.3
34.3.2.4
34.3.3
34.3.3.1
34.3.3.2
34.3.3.2.1
34.3.3.2.2
34.3.3.3
34.4
34.4.1
34.4.2
34.4.2.1
34.4.2.1.1
34.4.2.1.2
Features .......................................................................................................................... 34-1
References.................................................................................................................. 34-3
IMA Versions Supported ........................................................................................... 34-3
MPC8280 Versions Supported................................................................................... 34-3
PHY-Layer Devices Supported.................................................................................. 34-4
ATM Features Not Supported .................................................................................... 34-4
Additional Impact on MPC8280 Features ................................................................. 34-4
IMA Protocol Overview ............................................................................................... 34-4
Introduction................................................................................................................ 34-4
IMA Frame Overview................................................................................................ 34-5
Overview of IMA Cells ............................................................................................. 34-7
IMA Control Cells ................................................................................................. 34-7
IMA Filler Cells..................................................................................................... 34-8
IMA Microcode Architecture ........................................................................................ 34-8
IMA Function Partitioning......................................................................................... 34-8
User Plane Functions Performed by Microcode.................................................... 34-9
Plane Management Functions Performed by Microcode....................................... 34-9
Transmit Architecture ................................................................................................ 34-9
TRL Operation..................................................................................................... 34-10
TRL Service Latency....................................................................................... 34-11
Non-TRL Operation............................................................................................. 34-11
Transmit Queue Operation Examples (ITC mode).............................................. 34-12
Differences in CTC Operation ............................................................................. 34-14
Receive Architecture................................................................................................ 34-15
Cell Reception Task ............................................................................................. 34-15
Cell Processing Activation Function ................................................................... 34-18
On-Demand Cell Processing ........................................................................... 34-18
IDCR-Regulated Cell Processing .................................................................... 34-19
Cell Processing Task............................................................................................ 34-20
IMA Programming Model ........................................................................................... 34-20
Data Structure Organization .................................................................................... 34-20
IMA FCC Programming .......................................................................................... 34-22
FCC Registers ..................................................................................................... 34-22
FPSMRx .......................................................................................................... 34-22
FTIRRx ............................................................................................................ 34-22
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
xl
Freescale Semiconductor
Contents
Paragraph
Number
34.4.2.2
34.4.2.2.1
34.4.2.2.2
34.4.2.3
34.4.3
34.4.3.1
34.4.4
34.4.4.1
34.4.4.1.1
34.4.4.1.2
34.4.4.1.3
34.4.4.1.4
34.4.4.2
34.4.4.2.1
34.4.4.2.2
34.4.4.2.3
34.4.4.2.4
34.4.5
34.4.5.1
34.4.5.1.1
34.4.5.1.2
34.4.5.1.3
34.4.5.2
34.4.5.2.1
34.4.5.2.2
34.4.5.3
34.4.6
34.4.6.1
34.4.6.2
34.4.7
34.4.7.1
34.4.7.2
34.4.8
34.4.8.1
34.4.8.2
34.4.8.2.1
34.4.8.2.2
34.4.8.2.3
34.4.8.3
34.4.8.4
34.4.8.5
Title
Page
Number
FCC Parameters ................................................................................................... 34-22
TCELL_TMP_BASE and RCELL_TMP_BASE ........................................... 34-22
GMODE........................................................................................................... 34-22
IMA-Specific FCC Parameters............................................................................ 34-22
IMA Root Table ....................................................................................................... 34-23
IMA Control (IMACNTL) .................................................................................. 34-25
IMA Group Tables ................................................................................................... 34-25
IMA Group Transmit Table Entry ....................................................................... 34-25
IMA Group Transmit Control (IGTCNTL) .................................................... 34-27
IMA Group Transmit State (IGTSTATE) ....................................................... 34-27
Transmit Group Order Table............................................................................ 34-28
ICP Cell Templates .......................................................................................... 34-29
IMA Group Receive Table Entry......................................................................... 34-31
IMA Group Receive Control (IGRCNTL) ..................................................... 34-34
IMA Group Receive State (IGRSTATE) ........................................................ 34-34
IMA Receive Group Frame Size .................................................................... 34-35
Receive Group Order Tables ........................................................................... 34-35
IMA Link Tables...................................................................................................... 34-36
IMA Link Transmit Table Entry .......................................................................... 34-36
IMA Link Transmit Control (ILTCNTL) ....................................................... 34-37
IMA Link Transmit State (ILTSTATE) .......................................................... 34-38
IMA Transmit Interrupt Status (ITINTSTAT) ................................................ 34-39
IMA Link Receive Table Entry ........................................................................... 34-40
IMA Link Receive Control (ILRCNTL) ........................................................ 34-41
IMA Link Receive State (ILRSTATE) ........................................................... 34-42
IMA Link Receive Statistics Table...................................................................... 34-43
Structures in External Memory................................................................................ 34-43
Transmit Queues .................................................................................................. 34-44
Delay Compensation Buffers (DCB)................................................................... 34-44
IMA Exceptions....................................................................................................... 34-45
IMA Interrupt Queue Entry ................................................................................. 34-45
ICP Cell Reception Exceptions ........................................................................... 34-46
IDCR Timer Programming ...................................................................................... 34-47
IDCR Master Clock ............................................................................................. 34-47
IDCR FCC Parameter Shadow ............................................................................ 34-47
MPC8280 Features Unavailable if IDCR is Used ........................................... 34-47
Programming the FCC Parameter Shadow...................................................... 34-48
On-the-Fly Changes of FCC Parameters ......................................................... 34-48
IDCR_Init Command........................................................................................... 34-49
IDCR Root Parameters ........................................................................................ 34-49
IDCR Table Entry ................................................................................................ 34-49
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
xli
Contents
Paragraph
Number
34.4.8.6
34.4.8.7
34.4.9
34.4.9.1
34.4.9.2
34.4.10
34.5
34.5.1
34.5.2
34.5.3
34.5.3.1
34.5.3.2
34.5.3.3
34.5.3.4
34.5.3.5
34.5.3.6
34.5.3.7
34.5.3.8
34.5.3.9
34.5.3.10
34.5.3.11
34.5.3.12
34.5.3.13
34.5.4
34.5.4.1
34.5.4.2
34.5.4.3
34.5.4.3.1
34.5.4.3.2
34.5.4.4
34.5.4.4.1
34.5.4.4.2
34.5.4.5
34.5.4.5.1
34.5.4.5.2
34.5.4.6
34.5.4.7
34.5.4.8
34.5.4.9
34.5.4.10
34.5.4.11
Title
Page
Number
IDCR Counter Algorithm .................................................................................... 34-50
IDCR Events........................................................................................................ 34-50
APC Programming for IMA .................................................................................... 34-51
Programming for CBR, UBR, VBR, and UBR+ ................................................. 34-52
Programming for ABR ........................................................................................ 34-52
Changing IMA Version............................................................................................ 34-53
IMA Software Interface and Requirements ................................................................. 34-53
Software Model........................................................................................................ 34-53
Initialization Procedure............................................................................................ 34-54
Software Responsibilities ........................................................................................ 34-54
System Definition ................................................................................................ 34-54
General Operation................................................................................................ 34-55
Receive Link State Machine Control................................................................... 34-55
Receive Group State Machine Control ................................................................ 34-55
Transmit Link State Machine Control ................................................................. 34-55
Transmit Group State Machine Control............................................................... 34-56
Group Symmetry Control .................................................................................... 34-56
ICP End-to-End Channel Transmission............................................................... 34-56
Link Addition and Slow Recovery (LASR) Procedure ....................................... 34-56
Failure Alarms ..................................................................................................... 34-56
Test Pattern Control ............................................................................................. 34-57
Performance Parameter Measurement and Reporting ......................................... 34-57
SNMP MIBs ........................................................................................................ 34-57
IMA Software Procedures ....................................................................................... 34-57
Transmit ICP Cell Signalling............................................................................... 34-57
Receive Link Start-up Procedure......................................................................... 34-57
Group Start-up Procedure ................................................................................... 34-58
As Initiator (TX).............................................................................................. 34-59
As Responder (RX) ......................................................................................... 34-60
Link Addition Procedure ..................................................................................... 34-60
Rx Steps ........................................................................................................... 34-61
TX Parameters ................................................................................................. 34-61
Link Removal Procedure ..................................................................................... 34-62
Rx Steps ........................................................................................................... 34-62
TX Parameters ................................................................................................. 34-63
Link Receive Deactivation Procedure ................................................................. 34-63
Link Receive Reactivation Procedure ................................................................. 34-64
TRL On-the-Fly Change Procedure..................................................................... 34-64
Transmit Event Response Procedures.................................................................. 34-65
Receive Event Response Procedures ................................................................... 34-65
Test Pattern Procedure ......................................................................................... 34-67
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
xlii
Freescale Semiconductor
Contents
Paragraph
Number
34.5.4.11.1
34.5.4.11.2
34.5.4.12
34.5.4.12.1
34.5.4.12.2
34.5.4.13
34.5.4.13.1
34.5.4.13.2
Title
Page
Number
As Initiator (NE).............................................................................................. 34-67
As Responder (FE) .......................................................................................... 34-67
IDCR Operation................................................................................................... 34-68
IDCR Start-up.................................................................................................. 34-68
Activating a Group in IDCR Mode ................................................................. 34-69
End-to-End Channel Signalling Procedure.......................................................... 34-69
Transmit ........................................................................................................... 34-69
Receive ............................................................................................................ 34-70
Chapter 35
ATM Transmission Convergence Layer
35.1
35.2
35.2.1
35.2.1.1
35.2.2
35.2.2.1
35.2.3
35.2.4
35.3
35.4
35.4.1
35.4.1.1
35.4.1.2
35.4.1.3
35.4.1.4
35.4.2
35.4.2.1
35.4.2.2
35.4.3
35.4.3.1
35.4.3.2
35.4.3.3
35.4.3.4
35.4.3.5
35.4.3.6
35.4.4
35.4.5
35.4.5.1
35.4.5.2
Features .......................................................................................................................... 35-2
Functionality .................................................................................................................. 35-3
Receive ATM Cell Functions..................................................................................... 35-3
Receive ATM 2-Cell FIFO .................................................................................... 35-5
Transmit ATM Cell Functions ................................................................................... 35-5
Transmit ATM 2-Cell FIFO................................................................................... 35-6
Receive UTOPIA Interface........................................................................................ 35-6
Transmit UTOPIA Interface ...................................................................................... 35-6
Signals............................................................................................................................ 35-6
TC Layer Programming Mode ...................................................................................... 35-6
TC Layer Registers .................................................................................................... 35-6
TC Layer Mode Registers 1–8 (TCMODEx) ........................................................ 35-7
Cell Delineation State Machine Registers 1–8 (CDSMRx)................................... 35-8
TC Layer Event Registers 1–8 (TCERx) ............................................................... 35-9
TC Layer Mask Register (TCMRx)..................................................................... 35-10
TC Layer General Registers .................................................................................... 35-10
TC Layer General Event Register (TCGER)....................................................... 35-10
TC Layer General Status Register (TCGSR)....................................................... 35-11
TC Layer Cell Counters........................................................................................... 35-11
Received Cell Counters 1–8 (TC_RCCx)............................................................ 35-11
Transmitted Cell Counters 1–8 (TC_TCCx)........................................................ 35-11
Errored Cell Counters 1–8 (TC_ECCx)............................................................... 35-12
Corrected Cell Counters 1–8 (TC_CCCx) ........................................................... 35-12
Transmitted IDLE Cell Counters 1–8 (TC_ICCx)............................................... 35-12
Filtered Cell Counters 1–8 (TC_FCCx)............................................................... 35-12
Programming FCC2................................................................................................. 35-12
Programming and Operating the TC Layer ............................................................. 35-12
Receive ................................................................................................................ 35-12
Transmit ............................................................................................................... 35-13
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
xliii
Contents
Paragraph
Number
35.5
35.5.1
35.5.2
35.5.3
35.5.4
35.5.5
35.5.6
35.5.7
35.5.8
35.5.9
Title
Page
Number
Implementation Example ............................................................................................. 35-15
Operating the TC Layer at Higher Frequencies....................................................... 35-15
Programming a T1 Application ............................................................................... 35-15
Step 1 ....................................................................................................................... 35-16
Step 2 ....................................................................................................................... 35-16
Step 3 ....................................................................................................................... 35-16
Step 4 ....................................................................................................................... 35-16
Step 5 ....................................................................................................................... 35-17
Step 6 ....................................................................................................................... 35-17
Step 7 ....................................................................................................................... 35-17
Chapter 36
Fast Ethernet Controller
36.1
36.2
36.3
36.3.1
36.4
36.5
36.6
36.7
36.8
36.9
36.10
36.11
36.12
36.13
36.14
36.15
36.16
36.17
36.18
36.18.1
36.18.2
36.19
36.20
Fast Ethernet on the MPC8280...................................................................................... 36-2
Features .......................................................................................................................... 36-2
Connecting the MPC8280 to Fast Ethernet ................................................................... 36-4
Connecting the MPC8280 to Ethernet (RMII) .......................................................... 36-5
Ethernet Channel Frame Transmission .......................................................................... 36-5
Ethernet Channel Frame Reception ............................................................................... 36-6
Flow Control .................................................................................................................. 36-7
CAM Interface ............................................................................................................... 36-8
Ethernet Parameter RAM............................................................................................... 36-8
Programming Model .................................................................................................... 36-12
Ethernet Command Set ................................................................................................ 36-12
RMON Support............................................................................................................ 36-14
Ethernet Address Recognition ..................................................................................... 36-15
Hash Table Algorithm.................................................................................................. 36-17
Interpacket Gap Time................................................................................................... 36-18
Handling Collisions ..................................................................................................... 36-18
Internal and External Loopback................................................................................... 36-18
Ethernet Error-Handling Procedure ............................................................................. 36-18
Fast Ethernet Registers ................................................................................................ 36-19
FCC Ethernet Mode Registers (FPSMRx)............................................................... 36-19
Ethernet Event Register (FCCE)/Mask Register (FCCM) ...................................... 36-21
Ethernet RxBDs ........................................................................................................... 36-23
Ethernet TxBDs ........................................................................................................... 36-26
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
xliv
Freescale Semiconductor
Contents
Paragraph
Number
Title
Page
Number
Chapter 37
FCC HDLC Controller
37.1
37.2
37.3
37.4
37.5
37.5.1
37.5.2
37.6
37.7
37.8
37.9
37.10
Key Features .................................................................................................................. 37-1
HDLC Channel Frame Transmission Processing .......................................................... 37-2
HDLC Channel Frame Reception Processing ............................................................... 37-3
HDLC Parameter RAM ................................................................................................. 37-3
Programming Model ...................................................................................................... 37-5
HDLC Command Set................................................................................................. 37-5
HDLC Error Handling ............................................................................................... 37-6
HDLC Mode Register (FPSMR) ................................................................................... 37-8
HDLC Receive Buffer Descriptor (RxBD).................................................................... 37-9
HDLC Transmit Buffer Descriptor (TxBD) ................................................................ 37-12
HDLC Event Register (FCCE)/Mask Register (FCCM) ............................................. 37-14
FCC Status Register (FCCS) ....................................................................................... 37-16
Chapter 38
FCC Transparent Controller
38.1
38.2
38.3
38.3.1
38.3.2
38.3.3
Features .......................................................................................................................... 38-1
Transparent Channel Operation ..................................................................................... 38-2
Achieving Synchronization in Transparent Mode ......................................................... 38-2
In-Line Synchronization Pattern................................................................................ 38-2
External Synchronization Signals.............................................................................. 38-3
Transparent Synchronization Example ...................................................................... 38-4
Chapter 39
Serial Peripheral Interface (SPI)
39.1
39.2
39.3
39.3.1
39.3.2
39.3.3
39.4
39.4.1
39.4.1.1
39.4.2
39.4.3
39.5
Features .......................................................................................................................... 39-1
SPI Clocking and Signal Functions ............................................................................... 39-2
Configuring the SPI Controller...................................................................................... 39-2
The SPI as a Master Device....................................................................................... 39-3
The SPI as a Slave Device ......................................................................................... 39-4
The SPI in Multimaster Operation............................................................................. 39-4
Programming the SPI Registers ..................................................................................... 39-6
SPI Mode Register (SPMODE) ................................................................................. 39-6
SPI Examples with Different SPMODE[LEN] Values.......................................... 39-8
SPI Event/Mask Registers (SPIE/SPIM) ................................................................... 39-9
SPI Command Register (SPCOM) .......................................................................... 39-10
SPI Parameter RAM .................................................................................................... 39-10
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
xlv
Contents
Paragraph
Number
39.5.1
39.6
39.7
39.7.1
39.7.1.1
39.7.1.2
39.8
39.9
39.10
Title
Page
Number
Receive/Transmit Function Code Registers (RFCR/TFCR).................................... 39-12
SPI Commands ............................................................................................................ 39-12
The SPI Buffer Descriptor (BD) Table ........................................................................ 39-13
SPI Buffer Descriptors (BDs) .................................................................................. 39-13
SPI Receive BD (RxBD) ..................................................................................... 39-14
SPI Transmit BD (TxBD) .................................................................................... 39-15
SPI Master Programming Example ............................................................................. 39-16
SPI Slave Programming Example................................................................................ 39-17
Handling Interrupts in the SPI ..................................................................................... 39-17
Chapter 40
Controller
I2C
40.1
40.2
40.3
40.3.1
40.3.2
40.3.3
40.3.4
40.4
40.4.1
40.4.2
40.4.3
40.4.4
40.4.5
40.5
40.6
40.7
40.7.1
40.7.1.1
40.7.1.2
Features .......................................................................................................................... 40-2
I2C Controller Clocking and Signal Functions.............................................................. 40-2
I2C Controller Transfers ................................................................................................ 40-2
I2C Master Write (Slave Read).................................................................................. 40-3
I2C Loopback Testing................................................................................................ 40-4
I2C Master Read (Slave Write).................................................................................. 40-4
I2C Multi-Master Considerations .............................................................................. 40-5
2C Registers .................................................................................................................. 40-5
I
I2C Mode Register (I2MOD) .................................................................................... 40-6
I2C Address Register (I2ADD) ................................................................................. 40-7
I2C Baud Rate Generator Register (I2BRG) ............................................................. 40-7
I2C Event/Mask Registers (I2CER/I2CMR) ............................................................. 40-7
I2C Command Register (I2COM) ............................................................................. 40-8
2
I C Parameter RAM....................................................................................................... 40-9
I2C Commands............................................................................................................. 40-11
The I2C Buffer Descriptor (BD) Table ........................................................................ 40-11
I2C Buffer Descriptors (BDs).................................................................................. 40-12
I2C Receive Buffer Descriptor (RxBD) .............................................................. 40-12
I2C Transmit Buffer Descriptor (TxBD) ............................................................. 40-13
Chapter 41
Parallel I/O Ports
41.1
41.2
41.2.1
41.2.2
41.2.3
Features .......................................................................................................................... 41-1
Port Registers ................................................................................................................. 41-1
Port Open-Drain Registers (PODRA–PODRD) ........................................................ 41-2
Port Data Registers (PDATA–PDATD) ..................................................................... 41-2
Port Data Direction Registers (PDIRA–PDIRD)....................................................... 41-3
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
xlvi
Freescale Semiconductor
Contents
Paragraph
Number
41.2.4
41.2.5
41.3
41.4
41.4.1
41.4.2
41.5
41.6
Title
Page
Number
Port Pin Assignment Register (PPAR)....................................................................... 41-4
Port Special Options Registers A–D (PSORA–PSORD) .......................................... 41-4
Port Block Diagram ....................................................................................................... 41-6
Port Pins Functions ........................................................................................................ 41-6
General Purpose I/O Pins........................................................................................... 41-7
Dedicated Pins ........................................................................................................... 41-7
Ports Tables .................................................................................................................... 41-7
Interrupts from Port C.................................................................................................. 41-20
Appendix A
Register Quick Reference Guide
A.1
A.2
A.3
PowerPC Registers—User Registers .............................................................................. A-1
PowerPC Registers—Supervisor Registers .................................................................... A-1
MPC8280-Specific SPRs ................................................................................................ A-3
Appendix B
Revision History
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
xlvii
Contents
Paragraph
Number
Title
Page
Number
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
xlviii
Freescale Semiconductor
Figures
Figure
Number
1-1
1-2
1-3
1-4
1-5
1-6
1-7
1-8
1-9
1-10
1-11
1-12
1-13
1-14
2-1
2-2
2-3
2-4
2-5
2-6
3-1
4-1
4-2
4-3
4-4
4-5
4-6
4-7
4-8
4-9
4-10
4-11
4-12
4-13
4-14
4-15
4-16
4-17
Title
Page
Number
Figures
MPC8280 Block Diagram....................................................................................................... 1-6
MPC8280 External Signals ..................................................................................................... 1-9
Remote Access Server Configuration ................................................................................... 1-13
Regional Office Router Configuration.................................................................................. 1-14
LAN-to-WAN Bridge Router Configuration ........................................................................ 1-15
Cellular Base Station Configuration ..................................................................................... 1-15
Telecommunications Switch Controller Configuration ........................................................ 1-16
SONET Transmission Controller Configuration .................................................................. 1-17
Basic System Configuration.................................................................................................. 1-18
High-Performance Communication ...................................................................................... 1-18
High-Performance System Microprocessor Configuration................................................... 1-19
PCI Configuration ................................................................................................................. 1-20
PCI with 155-Mbps ATM Configuration .............................................................................. 1-20
MPC8280 as PCI Agent ........................................................................................................ 1-21
MPC8280 Integrated Processor Core Block Diagram ............................................................ 2-2
MPC8280 Programming Model—Registers ......................................................................... 2-10
Hardware Implementation Register 0 (HID0) ...................................................................... 2-11
Hardware Implementation-Dependent Register 1 (HID1).................................................... 2-14
Hardware Implementation-Dependent Register 2 (HID2).................................................... 2-14
Data Cache Organization ...................................................................................................... 2-19
Internal Memory ..................................................................................................................... 3-1
SIU Block Diagram................................................................................................................. 4-1
System Configuration and Protection Logic ........................................................................... 4-3
Timers Clock Generation ........................................................................................................ 4-4
TMCNT Block Diagram ......................................................................................................... 4-5
PIT Block Diagram ................................................................................................................. 4-5
Software Watchdog Timer Service State Diagram.................................................................. 4-6
Software Watchdog Timer Block Diagram ............................................................................. 4-7
MPC8280 Interrupt Structure.................................................................................................. 4-8
Interrupt Request Masking.................................................................................................... 4-14
SIU Interrupt Configuration Register (SICR) ....................................................................... 4-17
SIU Interrupt Priority Register (SIPRR) ............................................................................... 4-18
CPM High Interrupt Priority Register (SCPRR_H).............................................................. 4-19
CPM Low Interrupt Priority Register (SCPRR_L)............................................................... 4-20
SIPNR_H .............................................................................................................................. 4-21
SIPNR_L ............................................................................................................................... 4-22
SIMR_H ................................................................................................................................ 4-23
SIMR_L ................................................................................................................................ 4-23
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
xlix
Figures
Figure
Number
4-18
4-19
4-20
4-21
4-22
4-23
4-24
4-25
4-26
4-27
4-28
4-29
4-30
4-31
4-32
4-33
4-34
4-35
4-36
4-37
4-38
4-39
4-40
4-41
4-42
5-1
5-2
5-3
5-4
5-5
5-6
5-7
6-1
7-1
8-1
8-2
8-3
8-4
8-5
8-6
8-7
Title
Page
Number
SIU Interrupt Vector Register (SIVEC) ................................................................................ 4-24
Interrupt Table Handling Example........................................................................................ 4-25
SIU External Interrupt Control Register (SIEXR) ................................................................ 4-26
Bus Configuration Register (BCR) ....................................................................................... 4-27
PPC_ACR ............................................................................................................................. 4-29
PPC_ALRH........................................................................................................................... 4-30
PPC_ALRL ........................................................................................................................... 4-31
LCL_ACR............................................................................................................................. 4-31
LCL_ALRH .......................................................................................................................... 4-32
LCL_ALRL........................................................................................................................... 4-33
SIU Model Configuration Register (SIUMCR) .................................................................... 4-33
Internal Memory Map Register (IMMR) .............................................................................. 4-36
System Protection Control Register (SYPCR)...................................................................... 4-37
60x Bus Transfer Error Status and Control Register 1 (TESCR1) ....................................... 4-39
60x Bus Transfer Error Status and Control Register 2 (TESCR2) ....................................... 4-41
Local Bus Transfer Error Status and Control Register 1 (L_TESCR1) ................................ 4-42
Local Bus Transfer Error Status and Control Register 2 (L_TESCR2) ................................ 4-43
Time Counter Status and Control Register (TMCNTSC) ..................................................... 4-44
Time Counter Register (TCMCNT)...................................................................................... 4-45
Time Counter Alarm Register (TMCNTAL) ........................................................................ 4-45
Periodic Interrupt Status and Control Register (PISCR)....................................................... 4-46
Periodic interrupt Timer Count Register (PITC) .................................................................. 4-47
Periodic Interrupt Timer Register (PITR) ............................................................................. 4-48
PCI Base Registers (PCIBRx)............................................................................................... 4-49
PCI Mask Register (PCIMSKx)............................................................................................ 4-50
Power-on Reset Flow .............................................................................................................. 5-3
Reset Status Register (RSR).................................................................................................... 5-4
Reset Mode Register (RMR)................................................................................................... 5-5
Hard Reset Configuration Word.............................................................................................. 5-8
Single Chip with Default Configuration ............................................................................... 5-10
Configuring a Single Chip from EPROM............................................................................. 5-11
Configuring Multiple Chips .................................................................................................. 5-12
MPC8280 External Signals ..................................................................................................... 6-2
Signal Groupings..................................................................................................................... 7-2
Single-MPC8280 Bus Mode ................................................................................................... 8-3
60x-Compatible Bus Mode ..................................................................................................... 8-4
Basic Transfer Protocol........................................................................................................... 8-5
Address Bus Arbitration with External Bus Master................................................................ 8-8
Address Pipelining .................................................................................................................. 8-9
Interface to Different Port Size Devices ............................................................................... 8-16
Retry Cycle ........................................................................................................................... 8-22
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
l
Freescale Semiconductor
Figures
Figure
Number
8-8
8-9
8-10
8-11
8-12
9-1
9-2
9-3
9-4
9-5
9-6
9-7
9-8
9-9
9-10
9-11
9-12
9-13
9-14
9-15
9-16
9-17
9-18
9-19
9-20
9-21
9-22
9-23
9-24
9-25
9-26
9-27
9-28
9-29
9-30
9-31
9-32
9-33
9-34
Title
Page
Number
Single-Beat and Burst Data Transfers................................................................................... 8-26
28-Bit Extended Transfer to 32-Bit Port Size ....................................................................... 8-27
Burst Transfer to 32-Bit Port Size......................................................................................... 8-28
Data Tenure Terminated by Assertion of TEA ..................................................................... 8-29
MEI Cache Coherency Protocol—State Diagram (WIM = 001) .......................................... 8-30
PCI Bridge in the MPC8280 ................................................................................................... 9-2
PCI Bridge Structure ............................................................................................................... 9-2
Single Beat Read Example.................................................................................................... 9-10
Burst Read Example.............................................................................................................. 9-10
Single Beat Write Example ................................................................................................... 9-11
Burst Write Example............................................................................................................. 9-11
Target-Initiated Terminations................................................................................................ 9-12
PCI Configuration Type 0 Translation
(Top = CONFIG_ADDR) (Bottom = PCI Address Lines) .............................................. 9-15
PCI Parity Operation ............................................................................................................. 9-18
PCI Arbitration Example ...................................................................................................... 9-20
Address Decode Flow Chart for 60x Bus Mastered Transactions ........................................ 9-21
Address Decode Flow Chart for PCI Mastered Transactions ............................................... 9-22
Address Decode Flow Chart for Embedded Utilities
(DMA, Message Unit) Mastered Transactions................................................................. 9-23
Address Map Example .......................................................................................................... 9-24
Inbound PCI Memory Address Translation .......................................................................... 9-25
Outbound PCI Memory Address Translation ....................................................................... 9-26
PCI Outbound Translation Address Registers (POTARx) .................................................... 9-30
PCI Outbound Base Address Registers (POBARx).............................................................. 9-31
PCI Outbound Comparison Mask Registers (POCMRx) ..................................................... 9-32
Discard Timer Control register (PTCR) ................................................................................ 9-33
General Purpose Control Register (GPCR) .......................................................................... 9-34
PCI General Control Register (PCI_GCR) ........................................................................... 9-35
Error Status Register (ESR) .................................................................................................. 9-36
Error Mask Register (EMR).................................................................................................. 9-37
Error Control Register (ECR) ............................................................................................... 9-38
PCI Error Address Capture Register (PCI_EACR) .............................................................. 9-39
PCI Error Data Capture Register (PCI_EDCR) .................................................................... 9-40
PCI Error Control Capture Register (PCI_ECCR) ............................................................... 9-41
PCI Inbound Translation Address Registers (PITARx) ........................................................ 9-42
PCI Inbound Base Address Registers (PIBARx) .................................................................. 9-43
PCI Inbound Comparison Mask Registers (PICMRx).......................................................... 9-44
PCI Bridge PCI Configuration Registers .............................................................................. 9-46
Vendor ID Register................................................................................................................ 9-47
Device ID Register................................................................................................................ 9-47
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
li
Figures
Figure
Number
9-35
9-36
9-37
9-38
9-39
9-40
9-41
9-42
9-43
9-44
9-45
9-46
9-47
9-48
9-49
9-50
9-51
9-52
9-53
9-54
9-55
9-56
9-57
9-58
9-59
9-60
9-61
9-62
9-63
9-64
9-65
9-66
9-67
9-68
9-69
9-70
9-71
9-72
9-73
9-74
Title
Page
Number
PCI Bus Command Register ................................................................................................. 9-48
PCI Bus Status Register ........................................................................................................ 9-49
Revision ID Register ............................................................................................................. 9-50
PCI Bus Programming Interface Register............................................................................. 9-50
Subclass Code Register ......................................................................................................... 9-51
PCI Bus Base Class Code Register ....................................................................................... 9-51
PCI Bus Cache Line Size Register........................................................................................ 9-52
PCI Bus Latency Timer Register .......................................................................................... 9-52
Header Type Register ............................................................................................................ 9-53
BIST Control Register .......................................................................................................... 9-53
PCI Bus Internal Memory-Mapped Registers Base Address Register
(PIMMRBAR).................................................................................................................. 9-54
General Purpose Local Access Base Address Registers (GPLABARx)............................... 9-55
Subsystem Vendor ID Register ............................................................................................. 9-55
Subsystem Device ID Register ............................................................................................. 9-56
PCI Bus Capabilities Pointer Register .................................................................................. 9-56
PCI Bus Interrupt Line Register............................................................................................ 9-57
PCI Bus Interrupt Pin Register.............................................................................................. 9-57
PCI Bus MIN GNT ............................................................................................................... 9-58
PCI Bus MAX LAT............................................................................................................... 9-58
PCI Bus Function Register.................................................................................................... 9-59
PCI Bus Arbiter Configuration Register ............................................................................... 9-60
Hot Swap Register Block ...................................................................................................... 9-61
Hot Swap Control Status Register......................................................................................... 9-61
Data Structure for Register Initialization .............................................................................. 9-64
PCI Configuration Data Structure for the EEPROM ............................................................ 9-66
Inbound Message Registers (IMRx) ..................................................................................... 9-67
Outbound Message Registers (OMRx) ................................................................................. 9-68
Outbound Doorbell Register (ODR) ..................................................................................... 9-69
Inbound Doorbell Register (IDR) ......................................................................................... 9-69
I2O Message Queue .............................................................................................................. 9-71
Inbound Free_FIFO Head Pointer Register (IFHPR) ........................................................... 9-72
Inbound Free_FIFO Tail Pointer Register (IFTPR) .............................................................. 9-73
Inbound Post_FIFO Head Pointer Register (IPHPR) ........................................................... 9-74
Inbound Post_FIFO Tail Pointer Register (IPTPR) .............................................................. 9-74
Outbound Free_FIFO Head Pointer Register (OFHPR) ....................................................... 9-75
Outbound Free_FIFO Tail Pointer Register (OFTPR).......................................................... 9-76
Outbound Post_FIFO Head Pointer Register (OPHPR) ....................................................... 9-77
Outbound Post_FIFO Tail Pointer Register (OPTPR) .......................................................... 9-78
Inbound FIFO Queue Port Register (IFQPR) ....................................................................... 9-79
Outbound FIFO Queue Port Register (OFQPR) ................................................................... 9-79
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
lii
Freescale Semiconductor
Figures
Figure
Number
9-75
9-76
9-77
9-78
9-79
9-80
9-81
9-82
9-83
9-84
9-85
9-86
9-87
9-88
9-89
10-1
10-2
10-3
10-4
10-5
10-6
11-1
11-2
11-3
11-4
11-5
11-6
11-7
11-8
11-9
11-10
11-11
11-12
11-13
11-14
11-15
11-16
11-17
11-18
11-19
11-20
Title
Page
Number
Outbound Message Interrupt Status Register (OMISR) ....................................................... 9-80
Outbound Message Interrupt Mask Register (OMIMR)....................................................... 9-81
Inbound Message Interrupt Status Register (IMISR)............................................................ 9-82
Inbound Message Interrupt Mask Register (IMIMR) ........................................................... 9-83
Messaging Unit Control Register (MUCR) .......................................................................... 9-84
Queue Base Address Register (QBAR) ................................................................................ 9-85
DMA Controller Block Diagram .......................................................................................... 9-86
DMA Mode Registers 0–3 (DMAMRx) ............................................................................... 9-89
DMA Status Registers 0–3 (DMASRx) ................................................................................ 9-91
DMA Current Descriptor Address Registers 0–3 (DMACDARx) ....................................... 9-92
DMA Source Address Registers 0–3 (DMASARx).............................................................. 9-93
DMA Destination Address Registers 0–3 (DMADARx)...................................................... 9-94
DMA Byte Count Registers 0–3 (DMABCRx) .................................................................... 9-95
DMA Next Descriptor Address Registers 0–3 (DMANDARx)............................................ 9-95
DMA Chain of Segment Descriptors .................................................................................... 9-97
MPC8280 System Clock Architecture.................................................................................. 10-3
PCI Bridge as an Agent, Operating from the PCI System Clock ......................................... 10-4
PCI Bridge as a Host, Generating the PCI System Clock..................................................... 10-5
PLL Filtering Circuit............................................................................................................. 10-5
System Clock Control Register (SCCR) ............................................................................... 10-6
System Clock Mode Register (SCMR) ................................................................................. 10-7
Dual-Bus Architecture .......................................................................................................... 11-2
Memory Controller Machine Selection................................................................................. 11-5
Simple System Configuration ............................................................................................... 11-6
Basic Memory Controller Operation..................................................................................... 11-7
Partial Data Valid for 32-Bit Port Size Memory, Double-Word Transfer ............................11-11
Base Registers (BRx) .......................................................................................................... 11-13
Option Registers (ORx)—SDRAM Mode .......................................................................... 11-15
ORx —GPCM Mode........................................................................................................... 11-17
ORx—UPM Mode .............................................................................................................. 11-19
60x/Local SDRAM Mode Register (PSDMR/LSDMR) .................................................... 11-20
Machine x Mode Registers (MxMR) .................................................................................. 11-26
Memory Data Register (MDR) ........................................................................................... 11-29
Memory Address Register (MAR)...................................................................................... 11-29
60x Bus-Assigned UPM Refresh Timer (PURT)................................................................ 11-30
Local Bus-Assigned UPM Refresh Timer (LURT)............................................................. 11-30
60x Bus-Assigned SDRAM Refresh Timer (PSRT) ........................................................... 11-31
Local Bus-Assigned SDRAM Refresh Timer (LSRT)........................................................ 11-32
Memory Refresh Timer Prescaler Register (MPTPR) ........................................................ 11-32
128-Mbyte SDRAM (Eight-Bank Configuration, Banks 1 and 8 Shown) ......................... 11-34
PRETOACT = 2 (2 Clock Cycles)...................................................................................... 11-39
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
liii
Figures
Figure
Number
11-21
11-22
11-23
11-24
11-25
11-26
11-27
11-28
11-29
11-30
11-31
11-32
11-33
11-34
11-35
11-36
11-37
11-38
11-39
11-40
11-41
11-42
11-43
11-44
11-45
11-46
11-47
11-48
11-49
11-50
11-51
11-52
11-53
11-54
11-55
11-56
11-57
11-58
11-59
11-60
Title
Page
Number
ACTTORW = 2 (2 Clock Cycles)....................................................................................... 11-40
CL = 2 (2 Clock Cycles) ..................................................................................................... 11-40
LDOTOPRE = 2 (–2 Clock Cycles).................................................................................... 11-41
WRC = 2 (2 Clock Cycles) ................................................................................................. 11-41
RFRC = 4 (6 Clock Cycles) ................................................................................................ 11-42
EAMUX = 1........................................................................................................................ 11-42
BUFCMD = 1...................................................................................................................... 11-43
SDRAM Single-Beat Read, Page Closed, CL = 3 .............................................................. 11-43
SDRAM Single-Beat Read, Page Hit, CL = 3 .................................................................... 11-44
SDRAM Two-Beat Burst Read, Page Closed, CL = 3........................................................ 11-44
SDRAM Four-Beat Burst Read, Page Miss, CL = 3........................................................... 11-44
SDRAM Single-Beat Write, Page Hit................................................................................. 11-45
SDRAM Three-Beat Burst Write, Page Closed .................................................................. 11-45
SDRAM Read-after-Read Pipeline, Page Hit, CL = 3........................................................ 11-45
SDRAM Write-after-Write Pipelined, Page Hit.................................................................. 11-46
SDRAM Read-after-Write Pipelined, Page Hit .................................................................. 11-46
SDRAM Mode-Set Command Timing ............................................................................... 11-47
Mode Data Bit Settings ....................................................................................................... 11-47
SDRAM Bank-Staggered CBR Refresh Timing................................................................. 11-48
GPCM-to-SRAM Configuration......................................................................................... 11-52
GPCM Peripheral Device Interface .................................................................................... 11-54
GPCM Peripheral Device Basic Timing (ACS = 1x and TRLX = 0) ................................. 11-55
GPCM Memory Device Interface ....................................................................................... 11-55
GPCM Memory Device Basic Timing (ACS = 00, CSNT = 1, TRLX = 0)....................... 11-56
GPCM Memory Device Basic Timing (ACS ≠ 00, CSNT = 1, TRLX = 0)....................... 11-56
GPCM Relaxed Timing Read (ACS = 1x, SCY = 1, CSNT = 0, TRLX = 1) .................... 11-57
GPCM Relaxed-Timing Write (ACS = 1x, SCY = 0, CSNT = 0,TRLX = 1) .................... 11-57
GPCM Relaxed-Timing Write (ACS = 10, SCY = 0, CSNT = 1, TRLX = 1) ................... 11-58
GPCM Relaxed-Timing Write (ACS = 00, SCY = 0, CSNT = 1, TRLX = 1) ................... 11-58
GPCM Read Followed by Read (ORx[29–30] = 00, Fastest Timing) ................................ 11-59
GPCM Read Followed by Read (ORx[29–30] = 01).......................................................... 11-60
GPCM Read Followed by Write (ORx[29–30] = 01) ......................................................... 11-60
GPCM Read Followed by Write (ORx[29–30] = 10) ......................................................... 11-61
External Termination of GPCM Access.............................................................................. 11-62
User-Programmable Machine Block Diagram.................................................................... 11-64
RAM Array Indexing .......................................................................................................... 11-65
Memory Refresh Timer Request Block Diagram ............................................................... 11-66
Memory Controller UPM Clock Scheme for Integer Clock Ratios.................................... 11-68
Memory Controller UPM Clock Scheme for Non-Integer (2.5:1/3.5:1)
Clock Ratios ................................................................................................................... 11-69
UPM Signals Timing Example ........................................................................................... 11-70
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
liv
Freescale Semiconductor
Figures
Figure
Number
11-61
11-62
11-63
11-64
11-65
11-66
11-67
11-68
11-69
11-70
11-71
11-72
11-73
11-74
11-75
11-76
11-77
11-78
11-79
11-80
11-81
11-82
11-83
11-84
11-85
11-86
12-1
12-2
12-3
12-4
13-1
13-2
13-3
13-4
13-5
13-6
14-1
14-2
14-3
14-4
Title
Page
Number
RAM Array and Signal Generation .................................................................................... 11-71
The RAM Word................................................................................................................... 11-71
CS Signal Selection............................................................................................................. 11-76
BS Signal Selection............................................................................................................. 11-76
UPM Read Access Data Sampling...................................................................................... 11-79
Wait Mechanism Timing for Internal and External Synchronous Masters ......................... 11-80
DRAM Interface Connection to the 60x Bus (64-Bit Port Size) ........................................ 11-82
Single-Beat Read Access to FPM DRAM .......................................................................... 11-84
Single-Beat Write Access to FPM DRAM ......................................................................... 11-85
Burst Read Access to FPM DRAM (No LOOP) ................................................................ 11-86
Burst Read Access to FPM DRAM (LOOP) ...................................................................... 11-87
Burst Write Access to FPM DRAM (No LOOP)................................................................ 11-88
Refresh Cycle (CBR) to FPM DRAM ................................................................................ 11-89
Exception Cycle .................................................................................................................. 11-90
FPM DRAM Burst Read Access (Data Sampling on Falling Edge of CLKIN)................. 11-92
MPC8280/EDO Interface Connection to the 60x Bus ........................................................ 11-93
Single-Beat Read Access to EDO DRAM.......................................................................... 11-94
Single-Beat Write Access to EDO DRAM ......................................................................... 11-95
Single-Beat Write Access to EDO DRAM Using REDO to Insert Three
Wait States ...................................................................................................................... 11-96
Burst Read Access to EDO DRAM .................................................................................... 11-97
Burst Write Access to EDO DRAM ................................................................................... 11-98
Refresh Cycle (CBR) to EDO DRAM................................................................................ 11-99
Exception Cycle For EDO DRAM ................................................................................... 11-100
Pipelined Bus Operation and Memory Access in 60x-Compatible Mode ........................ 11-104
External Master Access (GPCM)...................................................................................... 11-105
External Master Configuration with SDRAM Device...................................................... 11-106
L2 Cache in Copy-Back Mode.............................................................................................. 12-2
External L2 Cache in Write-Through Mode ......................................................................... 12-4
External L2 Cache in ECC/Parity Mode............................................................................... 12-6
Read Access with L2 Cache.................................................................................................. 12-8
Test Logic Block Diagram .................................................................................................... 13-2
TAP Controller State Machine .............................................................................................. 13-3
Output Pin Cell (O.Pin)......................................................................................................... 13-4
Observe-Only Input Pin Cell (I.Obs) .................................................................................... 13-4
Output Control Cell (IO.CTL) .............................................................................................. 13-5
General Arrangement of Bidirectional Pin Cells .................................................................. 13-5
CPM Block Diagram............................................................................................................. 14-3
Communications Processor (CP) Block Diagram................................................................. 14-6
RISC Controller Configuration Register (RCCR.................................................................. 14-9
RISC Time-Stamp Control Register (RTSCR) ................................................................... 14-11
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
lv
Figures
Figure
Number
14-5
14-6
14-7
14-8
14-9
14-10
14-11
14-12
15-1
15-2
15-3
15-4
15-5
15-6
15-7
15-8
15-9
15-10
15-11
15-12
15-13
15-14
15-15
15-16
15-17
15-18
15-19
15-20
15-21
15-22
15-23
15-24
16-1
16-2
16-3
16-4
16-5
16-6
16-7
16-8
16-9
Title
Page
Number
RISC Time-Stamp Register (RTSR) ................................................................................... 14-11
CP Command Register (CPCR).......................................................................................... 14-12
Internal RAM Block Diagram............................................................................................. 14-18
Internal Data RAM Memory Map ...................................................................................... 14-19
Instruction RAM Partitioning ............................................................................................. 14-20
RISC Timer Table RAM Usage .......................................................................................... 14-24
RISC Timer Command Register (TM_CMD) .................................................................... 14-25
RISC Timer Event Register (RTER)/Mask Register (RTMR)............................................ 14-26
SI Block Diagram.................................................................................................................. 15-2
Various Configurations of a Single TDM Channel ............................................................... 15-5
Dual TDM Channel Example ............................................................................................... 15-6
Enabling Connections to the TSA......................................................................................... 15-8
One TDM Channel with Static Frames and Independent Rx and Tx Routes ....................... 15-9
One TDM Channel with Shadow RAM for Dynamic Route Change................................. 15-10
SIx RAM Entry Fields ........................................................................................................ 15-10
Using the SWTR Feature .................................................................................................... 15-12
Example: SIx RAM Dynamic Changes, TDMa and b, Same SIx RAM Size .................... 15-16
SI Global Mode Registers (SIxGMR)................................................................................. 15-17
SI Mode Registers (SIxMR) ............................................................................................... 15-18
One-Clock Delay from Sync to Data (xFSD = 01)............................................................. 15-20
No Delay from Sync to Data (xFSD = 00).......................................................................... 15-20
Falling Edge (FE) Effect When CE = 1 and xFSD = 01..................................................... 15-21
Falling Edge (FE) Effect When CE = 0 and xFSD = 01..................................................... 15-21
Falling Edge (FE) Effect When CE = 1 and xFSD = 00..................................................... 15-22
Falling Edge (FE) Effect When CE = 0 and xFSD = 00..................................................... 15-23
SIx RAM Shadow Address Registers (SIxRSR) ................................................................ 15-24
SI Command Register (SIxCMDR) .................................................................................... 15-24
SI Status Registers (SIxSTR) .............................................................................................. 15-25
Dual IDL Bus Application Example ................................................................................... 15-26
IDL Terminal Adaptor......................................................................................................... 15-27
IDL Bus Signals .................................................................................................................. 15-28
GCI Bus Signals.................................................................................................................. 15-31
CPM Multiplexing Logic (CMX) Block Diagram................................................................ 16-2
Enabling Connections to the TSA......................................................................................... 16-4
Bank of Clocks...................................................................................................................... 16-5
CMX UTOPIA Address Register (CMXUAR) .................................................................... 16-7
Connection of the Master Address........................................................................................ 16-9
Connection of the Slave Address .......................................................................................... 16-9
Multi-PHY Receive Address Multiplexing......................................................................... 16-11
CMX SI1 Clock Route Register (CMXSI1CR) .................................................................. 16-12
CMX SI2 Clock Route Register (CMXSI2CR) .................................................................. 16-13
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
lvi
Freescale Semiconductor
Figures
Figure
Number
16-10
16-11
16-12
17-1
17-2
18-1
18-2
18-3
18-4
18-5
18-6
18-7
18-8
18-9
19-1
19-2
19-3
19-4
19-5
19-6
19-7
19-8
19-9
19-10
20-1
20-2
20-3
20-4
20-5
20-6
20-7
20-8
20-9
20-10
20-11
20-12
20-13
20-14
20-15
21-1
Title
Page
Number
CMX FCC Clock Route Register (CMXFCR) ................................................................... 16-14
CMX SCC Clock Route Register (CMXSCR) ................................................................... 16-16
CMX SMC Clock Route Register (CMXSMR) ................................................................. 16-19
Baud-Rate Generator (BRG) Block Diagram ....................................................................... 17-1
Baud-Rate Generator Configuration Registers (BRGCx)..................................................... 17-2
Timer Block Diagram ........................................................................................................... 18-1
Timer Cascaded Mode Block Diagram................................................................................. 18-3
Timer Global Configuration Register 1 (TGCR1) ................................................................ 18-4
Timer Global Configuration Register 2 (TGCR2) ................................................................ 18-5
Timer Mode Registers (TMR1–TMR4)................................................................................ 18-6
Timer Reference Registers (TRR1–TRR4)........................................................................... 18-7
Timer Capture Registers (TCR1–TCR4) .............................................................................. 18-7
Timer Counter Registers (TCN1–TCN4).............................................................................. 18-7
Timer Event Registers (TER1–TER4) .................................................................................. 18-8
SDMA Data Paths ................................................................................................................. 19-1
SDMA Bus Arbitration (Transaction Steal).......................................................................... 19-3
SDMA Status Register (SDSR) ............................................................................................ 19-3
SDMA Transfer Error MSNUM Registers (PDTEM/LDTEM) ........................................... 19-4
IDMA Transfer Buffer in the Dual-Port RAM ..................................................................... 19-7
Example IDMA Transfer Buffer States for a Memory-to-Memory Transfer
(Size = 128 Bytes) ............................................................................................................ 19-8
IDMAx Channel BD Table.................................................................................................. 19-15
DCM Parameters................................................................................................................. 19-18
IDMA Event/Mask Registers (IDSR/IDMR) ..................................................................... 19-23
IDMA BD Structure............................................................................................................ 19-23
SCC Block Diagram.............................................................................................................. 20-2
GSMR_H—General SCC Mode Register (High Order)....................................................... 20-3
GSMR_L—General SCC Mode Register (Low Order)........................................................ 20-5
Data Synchronization Register (DSR) .................................................................................. 20-9
Transmit-on-Demand Register (TODR) ............................................................................. 20-10
SCC Buffer Descriptors (BDs)............................................................................................ 20-11
SCC BD and Buffer Memory Structure .............................................................................. 20-12
Function Code Registers (RFCR and TFCR) ..................................................................... 20-15
Output Delay from RTS Asserted for Synchronous Protocols ........................................... 20-18
Output Delay from CTS Asserted for Synchronous Protocols ........................................... 20-18
CTS Lost in Synchronous Protocols ................................................................................... 20-19
Using CD to Control Synchronous Protocol Reception...................................................... 20-20
DPLL Receiver Block Diagram .......................................................................................... 20-21
DPLL Transmitter Block Diagram...................................................................................... 20-22
DPLL Encoding Examples.................................................................................................. 20-23
UART Character Format ....................................................................................................... 21-1
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
lvii
Figures
Figure
Number
21-2
21-3
21-4
21-5
21-6
21-7
21-8
21-9
21-10
21-11
21-12
22-1
22-2
22-3
22-4
22-5
22-6
22-7
22-8
22-9
22-10
22-11
22-12
22-13
22-14
22-15
22-16
23-1
23-2
23-3
23-4
23-5
23-6
23-7
23-8
23-9
24-1
24-2
24-3
24-4
24-5
Title
Page
Number
Two UART Multidrop Configurations.................................................................................. 21-7
Control Character Table ........................................................................................................ 21-8
Transmit Out-of-Sequence Register (TOSEQ) ................................................................... 21-10
Asynchronous UART Transmitter ...................................................................................... 21-11
Protocol-Specific Mode Register for UART (PSMR) ........................................................ 21-13
SCC UART Receiving using RxBDs.................................................................................. 21-16
SCC UART Receive Buffer Descriptor (RxBD) ................................................................ 21-17
SCC UART Transmit Buffer Descriptor (TxBD) ............................................................... 21-18
SCC UART Interrupt Event Example ................................................................................. 21-20
SCC UART Event Register (SCCE) and Mask Register (SCCM) ..................................... 21-20
SCC Status Register for UART Mode (SCCS) ................................................................... 21-21
HDLC Framing Structure...................................................................................................... 22-2
HDLC Address Recognition ................................................................................................. 22-4
HDLC Mode Register (PSMR)............................................................................................. 22-7
SCC HDLC Receive Buffer Descriptor (RxBD) .................................................................. 22-8
SCC HDLC Receiving Using RxBDs................................................................................. 22-11
SCC HDLC Transmit Buffer Descriptor (TxBD) ............................................................... 22-12
HDLC Event Register (SCCE)/HDLC Mask Register (SCCM) ........................................ 22-13
SCC HDLC Interrupt Event Example................................................................................. 22-15
CC HDLC Status Register (SCCS) ..................................................................................... 22-15
Typical HDLC Bus Multi-Master Configuration................................................................ 22-19
Typical HDLC Bus Single-Master Configuration............................................................... 22-20
Detecting an HDLC Bus Collision...................................................................................... 22-21
Nonsymmetrical Tx Clock Duty Cycle for Increased Performance ................................... 22-21
HDLC Bus Transmission Line Configuration .................................................................... 22-22
Delayed RTS Mode............................................................................................................. 22-22
HDLC Bus TDM Transmission Line Configuration .......................................................... 22-23
Classes of BISYNC Frames.................................................................................................. 23-1
Control Character Table and RCCM..................................................................................... 23-6
BISYNC SYNC (BSYNC) ................................................................................................... 23-7
BISYNC DLE (BDLE) ......................................................................................................... 23-8
Protocol-Specific Mode Register for BISYNC (PSMR) .................................................... 23-10
SCC BISYNC RxBD .......................................................................................................... 23-12
SCC BISYNC Transmit BD (TxBD) .................................................................................. 23-14
BISYNC Event Register (SCCE)/BISYNC Mask Register (SCCM) ................................. 23-16
SCC Status Registers (SCCS) ............................................................................................. 23-16
Sending Transparent Frames between MPC8280s ............................................................... 24-4
SCC Transparent Receive Buffer Descriptor (RxBD) .......................................................... 24-8
SCC Transparent Transmit Buffer Descriptor (TxBD) ....................................................... 24-10
SCC Transparent Event Register (SCCE)/Mask Register (SCCM).................................... 24-11
SCC Status Register in Transparent Mode (SCCS) ............................................................ 24-12
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
lviii
Freescale Semiconductor
Figures
Figure
Number
25-1
25-2
25-3
25-4
25-5
25-6
25-7
25-8
25-9
25-10
26-1
26-2
27-1
27-2
27-3
27-4
27-5
27-6
27-7
27-8
27-9
27-10
27-11
27-12
27-13
27-14
27-15
27-16
27-17
27-18
27-19
27-20
27-21
28-1
28-2
28-3
28-4
28-5
28-6
28-7
28-8
Title
Page
Number
Ethernet Frame Structure ...................................................................................................... 25-1
Ethernet Block Diagram........................................................................................................ 25-2
Connecting the MPC8280 to Ethernet .................................................................................. 25-4
Ethernet Address Recognition Flowchart ........................................................................... 25-11
Ethernet Mode Register (PSMR) ........................................................................................ 25-14
SCC Ethernet RxBD ........................................................................................................... 25-16
Ethernet Receiving using RxBDs ....................................................................................... 25-18
SCC Ethernet TxBD............................................................................................................ 25-19
SCC Ethernet Event Register (SCCE)/Mask Register (SCCM) ......................................... 25-20
Ethernet Interrupt Events Example ..................................................................................... 25-21
LocalTalk Frame Format....................................................................................................... 26-1
Connecting the MPC8280 to LocalTalk................................................................................ 26-3
USB Interface........................................................................................................................ 27-3
USB Function Block Diagram ............................................................................................. 27-5
USB Controller Operating Modes......................................................................................... 27-6
USB Controller Block Diagram ........................................................................................... 27-8
USB Controller Operating Modes......................................................................................... 27-9
Endpoint Pointer Registers (EPxPTR) ................................................................................ 27-13
Frame Number (FRAME_N) in Function Mode—Updated by USB Controller................ 27-15
Frame Number (FRAME_N) in Host Mode—Updated by Application Software ............. 27-15
USB Function Code Registers (RFCR and TFCR)............................................................. 27-16
USB Mode Register (USMOD) .......................................................................................... 27-17
USB Slave Address Register (USADR) ............................................................................. 27-18
USB Endpoint Registers (USEP1–USEP4) ........................................................................ 27-18
USB Command Register (USCOM) ................................................................................... 27-20
USB Event Register (USBER)............................................................................................ 27-20
USB Status Register (USBS) .............................................................................................. 27-21
USB Start of Frame Timer (USSFT)................................................................................... 27-22
USB Memory Structure....................................................................................................... 27-23
USB Receive Buffer Descriptor (Rx BD),.......................................................................... 27-24
USB Transmit Buffer Descriptor (Tx BD),......................................................................... 27-26
USB Transmit Buffer Descriptor (Tx BD),......................................................................... 27-28
USB Transaction Buffer Descriptor (TrBD), ...................................................................... 27-30
SMC Block Diagram............................................................................................................. 28-1
SMC Mode Registers (SMCMR1/SMCMR2)...................................................................... 28-3
SMC Memory Structure........................................................................................................ 28-5
SMC Function Code Registers (RFCR/TFCR)..................................................................... 28-8
SMC UART Frame Format................................................................................................. 28-10
SMC UART RxBD ............................................................................................................. 28-14
RxBD Example ................................................................................................................... 28-16
SMC UART TxBD.............................................................................................................. 28-17
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
lix
Figures
Figure
Number
28-9
28-10
28-11
28-12
28-13
28-14
28-15
28-16
28-17
28-18
28-19
29-1
29-2
29-3
29-4
29-5
29-6
29-7
29-8
29-9
29-10
29-11
29-12
29-13
29-14
29-15
29-16
29-17
29-18
29-19
29-20
29-21
29-22
30-1
30-2
30-3
30-4
30-5
30-6
30-7
30-8
Title
Page
Number
SMC UART Event Register (SMCE)/Mask Register (SMCM) ......................................... 28-18
SMC UART Interrupts Example......................................................................................... 28-19
Synchronization with SMSYNx.......................................................................................... 28-23
Synchronization with the TSA............................................................................................ 28-24
SMC Transparent RxBD ..................................................................................................... 28-26
SMC Transparent Event Register (SMCE)/Mask Register (SMCM) ................................. 28-28
SMC Monitor Channel RxBD............................................................................................. 28-32
SMC Monitor Channel TxBD............................................................................................. 28-33
SMC C/I Channel RxBD..................................................................................................... 28-33
SMC C/I Channel TxBD..................................................................................................... 28-34
SMC GCI Event Register (SMCE)/Mask Register (SMCM) ............................................. 28-35
BD Structure for One MCC .................................................................................................. 29-3
TSTATE High Byte ............................................................................................................... 29-7
INTMSK Mask Bits .............................................................................................................. 29-8
Channel Mode Register (CHAMR) ...................................................................................... 29-8
Rx Internal State (RSTATE) High Byte .............................................................................. 29-10
Channel Mode Register (CHAMR)—Transparent Mode ................................................... 29-12
INTMSK Mask Bits ............................................................................................................ 29-15
Channel Mode Register (CHAMR)—CES Mode............................................................... 29-15
Extended Channel Mode Register (ECHAMR).................................................................. 29-21
SS7 Configuration Register (SS7_OPT) ............................................................................. 29-23
Mask1 Format ..................................................................................................................... 29-25
Mask2 Format ..................................................................................................................... 29-25
Super Channel Table Entry ................................................................................................. 29-28
Transmitter Super Channel Example .................................................................................. 29-30
Receiver Super Channel with Slot Synchronization Example............................................ 29-31
Receiver Super Channel without Slot Synchronization Example....................................... 29-32
SI MCC Configuration Register (MCCF)........................................................................... 29-32
Interrupt Circular Table....................................................................................................... 29-35
MCC Event Register (MCCE)/Mask Register (MCCM).................................................... 29-36
Interrupt Circular Table Entry............................................................................................. 29-37
MCC Receive Buffer Descriptor (RxBD)........................................................................... 29-42
MCC Transmit Buffer Descriptor (TxBD).......................................................................... 29-44
FCC Block Diagram.............................................................................................................. 30-3
General FCC Mode Register (GFMR).................................................................................. 30-4
General FCC Expansion Mode Register (GFEMR) ............................................................. 30-8
FCC Data Synchronization Register (FDSR) ....................................................................... 30-9
FCC Transmit-on-Demand Register (FTODR)..................................................................... 30-9
FCC Memory Structure....................................................................................................... 30-10
Buffer Descriptor Format.................................................................................................... 30-11
Function Code Register (FCRx) ......................................................................................... 30-14
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
lx
Freescale Semiconductor
Figures
Figure
Number
30-9
30-10
30-11
30-12
31-1
31-2
31-3
31-4
31-5
31-6
31-7
31-8
31-9
31-10
31-11
31-12
31-13
31-14
31-15
31-16
31-17
31-18
31-19
31-20
31-21
31-22
31-23
31-24
31-25
31-26
31-27
31-28
31-29
31-30
31-31
31-32
31-33
31-34
31-35
31-36
31-37
Title
Page
Number
Output Delay from RTS Asserted ....................................................................................... 30-18
Output Delay from CTS Asserted....................................................................................... 30-18
CTS Lost ............................................................................................................................. 30-19
Using CD to Control Reception .......................................................................................... 30-20
APC Scheduling Table Mechanism ...................................................................................... 31-9
VBR Pacing Using the GCRA (Leaky Bucket Algorithm) ................................................ 31-12
External CAM Data Input Fields ........................................................................................ 31-14
External CAM Output Fields .............................................................................................. 31-14
Address Compression Mechanism...................................................................................... 31-15
General VCOFFSET Formula for Contiguous VCLTs ....................................................... 31-16
VP Pointer Address Compression....................................................................................... 31-17
VC Pointer Address Compression ...................................................................................... 31-18
ATM Address Recognition Flowchart ................................................................................ 31-19
MPC8280’s ABR Basic Model ........................................................................................... 31-20
ABR Transmit Flow ............................................................................................................ 31-22
ABR Transmit Flow (continued) ........................................................................................ 31-23
ABR Transmit Flow (continued) ........................................................................................ 31-24
ABR Receive Flow ............................................................................................................. 31-25
Rate Format for RM Cells................................................................................................... 31-26
Rate Formula for RM Cells................................................................................................. 31-26
Performance Monitoring Cell Structure (FMCs and BRCs)............................................... 31-29
FMC, BRC Insertion ........................................................................................................... 31-31
Format of User-Defined Cells............................................................................................. 31-32
External CAM Address in UDC Extended Address Mode................................................. 31-33
ATM-to-TDM Interworking................................................................................................ 31-34
VCI Filtering Enable Bits ................................................................................................... 31-39
Global Mode Entry (GMODE) ........................................................................................... 31-40
Example of a 1024-Entry Receive Connection Table ......................................................... 31-42
Receive Connection Table (RCT) Entry ............................................................................. 31-43
AAL5 Protocol-Specific RCT............................................................................................. 31-46
AAL5-ABR Protocol-Specific RCT ................................................................................... 31-47
AAL1 Protocol-Specific RCT............................................................................................. 31-47
AAL0 Protocol-Specific RCT............................................................................................. 31-49
Transmit Connection Table (TCT) Entry ............................................................................ 31-50
AAL5 Protocol-Specific TCT ............................................................................................. 31-53
AAL1 Protocol-Specific TCT ............................................................................................. 31-54
AAL0 Protocol-Specific TCT ............................................................................................. 31-55
Transmit Connection Table Extension (TCTE)—VBR Protocol-Specific ......................... 31-56
UBR+ Protocol-Specific TCTE .......................................................................................... 31-57
ABR Protocol-Specific TCTE ............................................................................................ 31-58
OAM Performance Monitoring Table................................................................................. 31-60
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
lxi
Figures
Figure
Number
31-38
31-39
31-40
31-41
31-42
31-43
31-44
31-45
31-46
31-47
31-48
31-49
31-50
31-51
31-52
31-53
31-54
31-55
31-56
31-57
31-58
31-59
31-60
31-61
31-62
31-63
31-64
31-65
31-66
31-67
31-68
31-69
32-1
32-2
32-3
32-4
32-5
32-6
32-7
32-8
32-9
Title
Page
Number
ATM Pace Control Data Structure ...................................................................................... 31-62
The APC Scheduling Table Structure ................................................................................. 31-63
Control Slot ......................................................................................................................... 31-64
Transmit Buffers and BD Table Example ........................................................................... 31-65
Receive Static Buffer Allocation Example ......................................................................... 31-66
Receive Global Buffer Allocation Example ....................................................................... 31-67
Free Buffer Pool Structure .................................................................................................. 31-67
Free Buffer Pool Entry ........................................................................................................ 31-68
AAL5 RxBD ....................................................................................................................... 31-69
AAL1 RxBD ....................................................................................................................... 31-71
AAL0 RxBD ....................................................................................................................... 31-72
User-Defined Cell—RxBD Extension ................................................................................ 31-73
AAL5 TxBD ....................................................................................................................... 31-74
AAL1 TxBD ....................................................................................................................... 31-75
AAL0 TxBDs ...................................................................................................................... 31-76
User-Defined Cell—TxBD Extension ................................................................................ 31-77
AAL1 Sequence Number (SN) Protection Table ................................................................ 31-78
Interrupt Queue Structure.................................................................................................... 31-79
Interrupt Queue Entry ......................................................................................................... 31-80
UTOPIA Master Mode Signals........................................................................................... 31-81
UTOPIA Slave Mode Signals ............................................................................................. 31-83
FCC ATM Mode Register (FPSMR) .................................................................................. 31-86
ATM Event Register (FCCE)/FCC Mask Register (FCCM) .............................................. 31-88
COMM_INFO Field ........................................................................................................... 31-89
FCC Transmit Internal Rate Register (FTIRR)................................................................... 31-92
FCC Transmit Internal Rate Clocking ................................................................................ 31-92
FCC Transmit Internal Rate Port Enable Register (FIRPERx)........................................... 31-94
FCC Internal Rate Event Register (FIRERx)...................................................................... 31-95
FCC Internal Rate Selection Register HI (FIRSRx_HI) ..................................................... 31-96
FCC Internal Rate Selection Register LO (FIRSRx_LO)................................................... 31-96
AAL1 CES SRTS Generation Using External Logic.......................................................... 31-97
AAL1 CES SRTS Clock Recovery Using External Logic ................................................. 31-98
AAL1 Transmit Cell Format ................................................................................................. 32-3
AAL1 SDT Cell Types.......................................................................................................... 32-3
AAL1 Framing Formats........................................................................................................ 32-4
AAL1 CES Receiver Data flow ............................................................................................ 32-6
ATM-to-TDM Interworking.................................................................................................. 32-7
TDM-to-ATM Interworking.................................................................................................. 32-8
Mapping CAS Data on a Serial Interface............................................................................ 32-10
Internal CAS Block Formats............................................................................................... 32-11
Mapping CAS Entry............................................................................................................ 32-12
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
lxii
Freescale Semiconductor
Figures
Figure
Number
32-10
32-11
32-12
32-13
32-14
32-15
32-16
32-17
32-18
32-19
32-20
32-21
32-22
32-23
32-24
32-25
32-26
32-27
32-28
32-29
32-30
32-31
32-32
33-1
33-2
33-3
33-4
33-5
33-6
33-7
33-8
33-9
33-10
33-11
33-12
33-13
33-14
33-15
33-16
33-17
33-18
Title
Page
Number
AAL1 CES CAS Routing Table (CRT) .............................................................................. 32-12
AAL1 CES CAS Routing Table Entry................................................................................ 32-12
CAS Flow TDM-to-ATM.................................................................................................... 32-13
CAS Flow ATM-to-TDM.................................................................................................... 32-14
Data Structure for ATM-to-TDM Adaptive Slip Control ................................................... 32-16
CES Adaptive Threshold Table........................................................................................... 32-17
Pre-Underrun Sequence ...................................................................................................... 32-18
Pre-Overrun Sequence ........................................................................................................ 32-19
Recoverable Sync Fail Sequence Options .......................................................................... 32-20
3-Step-SN-Algorithm .......................................................................................................... 32-21
Pointer Verification Mechanism.......................................................................................... 32-22
Receive Connection Table (RCT) Entry ............................................................................. 32-26
AAL1 CES Protocol-Specific RCT .................................................................................... 32-29
Transmit Connection Table (TCT) Entry ........................................................................... 32-32
AAL1 CES Protocol-Specific TCT..................................................................................... 32-34
Outgoing CAS Status Register (OCASSR)......................................................................... 32-36
Transmit Buffers and BD Table Example ........................................................................... 32-37
Receive Buffers and BD Table Example ............................................................................ 32-38
AAL1 CES RxBD............................................................................................................... 32-39
AAL1 CES TxBD ............................................................................................................... 32-40
AAL1 CES Interrupt Queue Entry...................................................................................... 32-41
AAL1 Sequence Number (SN) Protection Table ................................................................ 32-43
TDM-to-ATM Timing Issue................................................................................................ 32-45
AAL2 Data Units .................................................................................................................. 33-1
AAL2 Sublayer Structure...................................................................................................... 33-2
AAL2 Switching Example .................................................................................................... 33-3
Round Robin Priority ............................................................................................................ 33-6
Fixed Priority Mode .............................................................................................................. 33-7
AAL2 Protocol-Specific Transmit Connection Table (TCT)................................................ 33-9
CPS Tx Queue Descriptor (TxQD) ..................................................................................... 33-13
Buffer Structure Example for CPS Packets......................................................................... 33-14
CPS TxBD........................................................................................................................... 33-15
CPS Packet Header Format................................................................................................. 33-16
SSSAR Tx Queue Descriptor.............................................................................................. 33-16
SSSAR TxBD ..................................................................................................................... 33-18
CID Mapping Process ......................................................................................................... 33-21
AAL2 Switching ................................................................................................................. 33-22
AAL2 Protocol-Specific Receive Connection Table (RCT) ............................................... 33-23
CPS Rx Queue Descriptor................................................................................................... 33-26
CPS Receive Buffer Descriptor .......................................................................................... 33-27
CPS Switch Rx Queue Descriptor ...................................................................................... 33-29
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
lxiii
Figures
Figure
Number
33-19
33-20
33-21
33-22
33-23
33-24
34-1
34-2
34-3
34-4
34-5
34-6
34-7
34-8
34-9
34-10
34-11
34-12
34-13
34-14
34-15
34-16
34-17
34-18
34-19
34-20
34-21
34-22
34-23
34-24
34-25
34-26
34-27
34-28
34-29
34-30
34-31
34-32
34-33
35-1
Title
Page
Number
Switch Receive/Transmit Buffer Descriptor ....................................................................... 33-29
SSSAR Rx Queue Descriptor ............................................................................................. 33-31
SSSAR Receive Buffer Descriptor ..................................................................................... 33-32
UDC Header Table.............................................................................................................. 33-37
AAL2 Interrupt Queue Entry CID ≠ 0 ................................................................................ 33-38
AAL2 Interrupt Queue Entry CID = 0 ................................................................................ 33-39
Basic Concept of IMA .......................................................................................................... 34-5
Illustration of IMA Frames ................................................................................................... 34-6
IMA Microcode Overview.................................................................................................... 34-7
IMA Frame and ICP Cell Formats........................................................................................ 34-8
IMA Transmit Task Interaction........................................................................................... 34-10
Transmit Queue Normal Operating State............................................................................ 34-12
Transmit Queue Behavior: Link Clock Rate Same as TRL ................................................ 34-12
Transmit Queue Behavior: Link Clock Rate Slower than TRL .......................................... 34-13
Transmit Queue Behavior: Link Clock Rate Faster than TRL, Worst-Case Event Sequence ......
34-14
IMA Receive Task Interaction ............................................................................................ 34-15
IMA Microcode: Receive Process ...................................................................................... 34-17
IMA Root Table Data Structures......................................................................................... 34-21
IMA Control (IMACNTL).................................................................................................. 34-25
IMA Group Transmit Control (IGTCNTL)......................................................................... 34-27
IMA Group Transmit State (IGTSTATE)............................................................................ 34-27
Transmit Group Order Table Entry ..................................................................................... 34-28
IMA Group Receive Control (IGRCNTL).......................................................................... 34-34
IMA Group Receive State (IGRSTATE)............................................................................. 34-34
IMA Receive Group Frame Size (IGRSTATE) .................................................................. 34-35
Receive Group Order Table Entry....................................................................................... 34-36
IMA Link Transmit Control (ILTCNTL)............................................................................ 34-38
IMA Link Transmit State (ILTSTATE) ............................................................................... 34-38
IMA Transmit Interrupt Status (ITINTSTAT)..................................................................... 34-39
IMA Link Receive Control (ILRCNTL)............................................................................. 34-41
IMA Link Receive State (ILRSTATE)................................................................................ 34-42
IMA Transmit Queue .......................................................................................................... 34-44
Cell Buffer in Delay Compensation Buffer......................................................................... 34-44
IMA Delay Compensation Buffer ....................................................................................... 34-45
IMA Interrupt Queue Entry................................................................................................. 34-45
IDMA Event/Mask Registers in IDCR Mode (IDSR/IDMR) ............................................ 34-50
COMM_INFO Field ........................................................................................................... 34-53
IMA Microcode/Software Interaction................................................................................. 34-54
Near-End versus Far-End .................................................................................................... 34-60
Serial ATM Using FCC2 and TC Blocks (Single Channel).................................................. 35-1
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
lxiv
Freescale Semiconductor
Figures
Figure
Number
35-2
35-3
35-4
35-5
35-6
35-7
35-8
35-9
35-10
35-11
35-12
36-1
36-2
36-3
36-4
36-5
36-6
36-7
36-8
36-9
36-10
36-11
37-1
37-2
37-3
37-4
37-5
37-6
37-7
37-8
37-9
38-1
38-2
39-1
39-2
39-3
39-4
39-5
39-6
39-7
39-8
Title
Page
Number
TC Layer Block Diagram...................................................................................................... 35-3
TC Cell Delineation State Machine ...................................................................................... 35-4
HEC: Receiver Modes of Operation ..................................................................................... 35-5
TC Layer Mode Registers (TCMODEx)............................................................................... 35-7
Cell Delineation State Machine Registers (CDSMRx) ......................................................... 35-8
TC Layer Event Registers (TCERx) ..................................................................................... 35-9
TC Layer General Event Register (TCGER) ...................................................................... 35-10
TC Layer General Status Register (TCGSR) ...................................................................... 35-11
TC Operation in FCC External Rate Mode......................................................................... 35-14
TC Operation in FCC Internal Rate Mode (Sub Rate Mode) ............................................. 35-14
Example of Serial ATM Application .................................................................................. 35-15
Ethernet Frame Structure ...................................................................................................... 36-1
Ethernet Block Diagram ....................................................................................................... 36-2
Connecting the MPC8280 to Ethernet .................................................................................. 36-4
Connecting the MPC8280 to Ethernet (RMII)...................................................................... 36-5
Ethernet Address Recognition Flowchart ........................................................................... 36-16
FCC Ethernet Mode Registers (FPSMRx) .......................................................................... 36-20
Ethernet Event Register (FCCE)/Mask Register (FCCM).................................................. 36-22
Ethernet Interrupt Events Example ..................................................................................... 36-23
Fast Ethernet Receive Buffer (RxBD) ................................................................................ 36-24
Ethernet Receiving Using RxBDs....................................................................................... 36-26
Fast Ethernet Transmit Buffer (TxBD) ............................................................................... 36-27
HDLC Framing Structure...................................................................................................... 37-2
HDLC Address Recognition Example.................................................................................. 37-5
HDLC Mode Register (FPSMR)........................................................................................... 37-8
FCC HDLC Receiving Using RxBDs................................................................................. 37-10
FCC HDLC Receive Buffer Descriptor (RxBD) ................................................................ 37-11
FCC HDLC Transmit Buffer Descriptor (TxBD) ............................................................... 37-12
HDLC Event Register (FCCE)/Mask Register (FCCM) .................................................... 37-14
HDLC Interrupt Event Example ......................................................................................... 37-16
FCC Status Register (FCCS)............................................................................................... 37-16
In-Line Synchronization Pattern ........................................................................................... 38-2
Sending Transparent Frames between MPC8280s ............................................................... 38-4
SPI Block Diagram ............................................................................................................... 39-1
Single-Master/Multi-Slave Configuration ............................................................................ 39-3
Multi-Master Configuration.................................................................................................. 39-5
SPMODE—SPI Mode Register ............................................................................................ 39-6
SPI Transfer Format with SPMODE[CP] = 0....................................................................... 39-7
SPI Transfer Format with SPMODE[CP] = 1....................................................................... 39-8
SPIE/SPIM—SPI Event/Mask Registers .............................................................................. 39-9
SPCOM—SPI Command Register ..................................................................................... 39-10
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
lxv
Figures
Figure
Number
39-9
39-10
39-11
39-12
40-1
40-2
40-3
40-4
40-5
40-6
40-7
40-8
40-9
40-10
40-11
40-12
40-13
40-14
41-1
41-2
41-3
41-4
41-5
41-6
41-7
Title
Page
Number
RFCR/TFCR—Function Code Registers............................................................................ 39-12
SPI Memory Structure......................................................................................................... 39-13
SPI RxBD............................................................................................................................ 39-14
SPI TxBD ............................................................................................................................ 39-15
I2C Controller Block Diagram .............................................................................................. 40-1
I2C Master/Slave General Configuration.............................................................................. 40-2
I2C Transfer Timing .............................................................................................................. 40-3
I2C Master Write Timing ...................................................................................................... 40-3
I2C Master Read Timing ....................................................................................................... 40-4
I2C Mode Register (I2MOD) ................................................................................................ 40-6
I2C Address Register (I2ADD) ............................................................................................. 40-7
I2C Baud Rate Generator Register (I2BRG)......................................................................... 40-7
I2C Event/Mask Registers (I2CER/I2CMR)......................................................................... 40-8
I2C Command Register (I2COM) ......................................................................................... 40-8
I2C Function Code Registers (RFCR/TFCR)...................................................................... 40-10
I2C Memory Structure......................................................................................................... 40-12
I2C RxBD............................................................................................................................ 40-13
I2C TxBD ............................................................................................................................ 40-14
Port Open-Drain Registers (PODRA–PODRD) ................................................................... 41-2
Port Data Registers (PDATA–PDATD) ................................................................................ 41-3
Port Data Direction Register (PDIR) .................................................................................... 41-3
Port Pin Assignment Register (PPARA–PPARD)................................................................. 41-4
Special Options Registers (PSORA–POSRD) ...................................................................... 41-5
Port Functional Operation ..................................................................................................... 41-6
Primary and Secondary Option Programming ...................................................................... 41-8
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
lxvi
Freescale Semiconductor
Tables
Table
Number
1-1
1-2
1-3
2-1
2-2
2-3
2-4
2-5
2-6
3-1
4-1
4-2
4-3
4-4
4-5
4-6
4-7
4-8
4-9
4-10
4-11
4-12
4-13
4-14
4-15
4-16
4-17
4-18
4-19
4-20
4-21
4-22
4-23
4-24
4-25
4-26
5-1
5-2
Title
Page
Number
Tables
MPC8280 Serial Protocols.................................................................................................... 1-10
Serial Performance ................................................................................................................ 1-11
MPC8270 Serial Performance .............................................................................................. 1-12
HID0 Field Descriptions ....................................................................................................... 2-11
HID1 Field Descriptions ....................................................................................................... 2-14
HID2 Field Descriptions ....................................................................................................... 2-15
Exception Classifications for the Processor Core ................................................................. 2-22
Exceptions and Conditions.................................................................................................... 2-23
Differences Between G2_LE Core and MPC603e................................................................ 2-27
Internal Memory Map ............................................................................................................. 3-2
System Configuration and Protection Functions .................................................................... 4-2
Interrupt Source Priority Levels............................................................................................ 4-10
Encoding the Interrupt Vector ............................................................................................... 4-14
SICR Field Descriptions ....................................................................................................... 4-18
SIPRR Field Descriptions ..................................................................................................... 4-19
SCPRR_H Field Descriptions ............................................................................................... 4-20
SCPRR_L Field Descriptions ............................................................................................... 4-21
SIEXR Field Descriptions..................................................................................................... 4-26
BCR Field Descriptions ........................................................................................................ 4-27
PPC_ACR Field Descriptions ............................................................................................... 4-30
LCL_ACR Field Descriptions .............................................................................................. 4-31
SIUMCR Register Field Descriptions................................................................................... 4-34
IMMR Field Descriptions ..................................................................................................... 4-37
SYPCR Field Descriptions.................................................................................................... 4-38
TESCR1 Field Descriptions.................................................................................................. 4-39
TESCR2 Field Descriptions.................................................................................................. 4-41
L_TESCR1 Field Descriptions ............................................................................................. 4-42
L_TESCR2 Field Descriptions ............................................................................................. 4-43
TMCNTSC Field Descriptions ............................................................................................. 4-44
TMCNTAL Field Descriptions ............................................................................................. 4-45
PISCR Field Descriptions ..................................................................................................... 4-46
PITC Field Descriptions........................................................................................................ 4-47
PITR Field Descriptions........................................................................................................ 4-48
PCIBRx Field Descriptions................................................................................................... 4-49
PCIMSKx Field Descriptions ............................................................................................... 4-50
SIU Pins Multiplexing Control ............................................................................................. 4-51
Reset Causes ........................................................................................................................... 5-1
Reset Actions for Each Reset Source...................................................................................... 5-2
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
lxvii
Tables
Table
Number
5-3
5-4
5-5
5-6
5-7
6-1
7-1
7-2
8-1
8-2
8-3
8-4
8-5
8-6
8-7
8-8
8-9
8-10
8-11
8-12
9-1
9-2
9-3
9-4
9-5
9-6
9-7
9-8
9-9
9-10
9-11
9-12
9-13
9-14
9-15
9-16
9-17
9-18
9-19
9-20
9-21
Title
Page
Number
RSR Field Descriptions........................................................................................................... 5-4
RMR Field Descriptions ......................................................................................................... 5-6
RSTCONF Connections in Multiple-MPC8280 Systems....................................................... 5-7
Configuration EPROM Addresses .......................................................................................... 5-7
Hard Reset Configuration Word Field Descriptions ............................................................... 5-8
External Signals ...................................................................................................................... 6-3
Data Bus Lane Assignments ................................................................................................. 7-13
DP[0–7] Signal Assignments ................................................................................................ 7-14
Terminology ............................................................................................................................ 8-1
Transfer Type Encoding ........................................................................................................ 8-10
Transfer Code Encoding for 60x Bus.................................................................................... 8-12
Transfer Size Signal Encoding.............................................................................................. 8-12
Burst Ordering....................................................................................................................... 8-13
Aligned Data Transfers ......................................................................................................... 8-14
Unaligned Data Transfer Example (4-Byte Example) .......................................................... 8-15
Data Bus: Read Cycle Requirements and Write Cycle Content ........................................... 8-17
Address and Size State Calculations ..................................................................................... 8-18
Data Bus Contents for Extended Write Cycles ..................................................................... 8-19
Data Bus Requirements for Extended Read Cycles.............................................................. 8-19
Address and Size State for Extended Transfers .................................................................... 8-20
PCI Terminology..................................................................................................................... 9-6
PCI Command Definitions...................................................................................................... 9-7
Internal Memory Map ........................................................................................................... 9-27
POTARx Field Descriptions ................................................................................................. 9-31
POBARx Field Descriptions ................................................................................................. 9-31
POCMRx Field Descriptions ................................................................................................ 9-32
PTCR Field Descriptions ...................................................................................................... 9-33
GPCR Field Descriptions...................................................................................................... 9-34
PCI_GCR Field Descriptions................................................................................................ 9-35
ESR Field Descriptions ......................................................................................................... 9-36
EMR Field Descriptions........................................................................................................ 9-37
ECR Field Descriptions ........................................................................................................ 9-39
PCI_EACR Field Descriptions ............................................................................................. 9-40
PCI_EDCR Field Description ............................................................................................... 9-40
PCI_ECCR Field Descriptions.............................................................................................. 9-41
PITARx Field Descriptions ................................................................................................... 9-42
PIBARx Field Descriptions .................................................................................................. 9-43
PICMRx Field Descriptions.................................................................................................. 9-44
PCI Bridge PCI Configuration Registers .............................................................................. 9-45
Vendor ID Register Description............................................................................................ 9-47
Device ID Register Description ............................................................................................ 9-47
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
lxviii
Freescale Semiconductor
Tables
Table
Number
9-22
9-23
9-24
9-25
9-26
9-27
9-28
9-29
9-30
9-31
9-32
9-33
9-34
9-35
9-36
9-37
9-38
9-39
9-40
9-41
9-42
9-43
9-44
9-45
9-46
9-47
9-48
9-49
9-50
9-51
9-52
9-53
9-54
9-55
9-56
9-57
9-58
9-59
9-60
9-61
9-62
Title
Page
Number
PCI Bus Command Register Description.............................................................................. 9-48
PCI Bus Status Register Description..................................................................................... 9-49
Revision ID Register Description ......................................................................................... 9-50
PCI Bus Programming Interface Register Description ......................................................... 9-50
Subclass Code Register Description ..................................................................................... 9-51
PCI Bus Base Class Code Register Description ................................................................... 9-51
PCI Bus Cache Line Size Register Description .................................................................... 9-52
PCI Bus Latency Timer Register Description....................................................................... 9-52
Header Type Register Description ........................................................................................ 9-53
BIST Control Register Description....................................................................................... 9-53
PIMMRBAR Field Descriptions........................................................................................... 9-54
GPLABARx Field Descriptions............................................................................................ 9-55
Subsystem Vendor ID Register Description.......................................................................... 9-56
Subsystem Device ID Description Register.......................................................................... 9-56
PCI Bus Capabilities Pointer Register Description............................................................... 9-56
PCI Bus Interrupt Line Register Description........................................................................ 9-57
PCI Bus Interrupt Pin Register Description.......................................................................... 9-57
PCI Bus MIN GNT Description............................................................................................ 9-58
PCI Bus MAX LAT Description ........................................................................................... 9-58
PCI Bus Function Register Field Descriptions ..................................................................... 9-59
PCI Bus Arbiter Configuration Register Field Description .................................................. 9-60
Hot Swap Register Block Field Descriptions ....................................................................... 9-61
Hot Swap Control Status Register Field Descriptions .......................................................... 9-62
Bit Settings for Register Initialization Data Structure .......................................................... 9-65
IMRx Field Descriptions....................................................................................................... 9-67
OMRx Field Descriptions ..................................................................................................... 9-68
ODR Field Descriptions........................................................................................................ 9-69
IDR Field Descriptions ......................................................................................................... 9-70
IFHPR Field Descriptions ..................................................................................................... 9-72
IFTPR Field Descriptions ..................................................................................................... 9-73
IPHPR Field Descriptions ..................................................................................................... 9-74
IPTPR Field Descriptions...................................................................................................... 9-75
OFHPR Field Descriptions ................................................................................................... 9-76
OFTPR Field Descriptions.................................................................................................... 9-76
OPHPR Field Descriptions ................................................................................................... 9-77
OPTPR Field Descriptions .................................................................................................... 9-78
IFQPR Field Descriptions ..................................................................................................... 9-79
OFQPR Field Descriptions ................................................................................................... 9-80
OMISR Field Descriptions.................................................................................................... 9-80
OMIMR Field Descriptions .................................................................................................. 9-81
IMISR Field Descriptions ..................................................................................................... 9-82
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
lxix
Tables
Table
Number
9-63
9-64
9-65
9-66
9-67
9-68
9-69
9-70
9-71
9-72
9-73
10-1
10-2
10-3
10-4
11-1
11-2
11-3
11-4
11-5
11-6
11-7
11-8
11-9
11-10
11-11
11-12
11-13
11-14
11-15
11-16
11-17
11-18
11-19
11-20
11-21
11-22
11-23
11-24
11-25
11-26
Title
Page
Number
IMIMR Field Descriptions.................................................................................................... 9-83
MUCR Field Descriptions .................................................................................................... 9-85
QBAR Field Descriptions ..................................................................................................... 9-85
DMAMRx Field Descriptions............................................................................................... 9-90
DMASRx Field Descriptions ................................................................................................ 9-92
DMACDARx Field Descriptions .......................................................................................... 9-93
DMASARx Field Descriptions ............................................................................................. 9-93
DMADARx Field Descriptions............................................................................................. 9-94
DMABCRx Field Descriptions ............................................................................................. 9-95
DMANDARx Field Descriptions.......................................................................................... 9-96
DMA Segment Descriptor Fields.......................................................................................... 9-96
Dedicated PLL Pins .............................................................................................................. 10-5
SCCR Field Descriptions ...................................................................................................... 10-6
SCMR Field Descriptions ..................................................................................................... 10-7
60x Bus-to-Core Frequency .................................................................................................. 10-8
Number of PSDVAL Assertions Needed for TA Assertion .................................................11-11
BADDR Connections.......................................................................................................... 11-12
60x Bus Memory Controller Registers ............................................................................... 11-12
BRx Field Descriptions ....................................................................................................... 11-13
ORx Field Descriptions (SDRAM Mode) .......................................................................... 11-16
ORx—GPCM Mode Field Descriptions ............................................................................. 11-17
Option Register (ORx)—UPM Mode ................................................................................. 11-19
PSDMR Field Descriptions................................................................................................. 11-21
LSDMR Field Descriptions ................................................................................................ 11-24
Machine x Mode Registers (MxMR) .................................................................................. 11-27
MDR Field Descriptions ..................................................................................................... 11-29
MAR Field Description....................................................................................................... 11-30
60x Bus-Assigned UPM Refresh Timer (PURT)................................................................ 11-30
Local Bus-Assigned UPM Refresh Timer (LURT)............................................................. 11-31
60x Bus-Assigned SDRAM Refresh Timer (PSRT) ........................................................... 11-31
LSRT Field Descriptions..................................................................................................... 11-32
MPTPR Field Descriptions ................................................................................................. 11-32
SDRAM Interface Signals .................................................................................................. 11-33
SDRAM Interface Commands ............................................................................................ 11-35
SDRAM Address Multiplexing (A0–A15) ......................................................................... 11-38
SDRAM Address Multiplexing (A16–A31) ....................................................................... 11-38
60x Address Bus Partition................................................................................................... 11-49
SDRAM Device Address Port during activate Command.................................................. 11-49
SDRAM Device Address Port during read/write Command .............................................. 11-49
Register Settings (Page-Based Interleaving)....................................................................... 11-50
60x Address Bus Partition................................................................................................... 11-50
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
lxx
Freescale Semiconductor
Tables
Table
Number
11-27
11-28
11-29
11-30
11-31
11-32
11-33
11-34
11-35
11-36
11-37
11-38
11-39
11-40
11-41
11-42
11-43
11-44
13-1
13-2
14-1
14-2
14-3
14-4
14-5
14-6
14-7
14-8
14-9
14-10
14-11
14-12
15-1
15-2
15-3
15-4
15-5
15-6
15-7
15-8
15-9
Title
Page
Number
SDRAM Device Address Port During activate Command ................................................. 11-51
SDRAM Device Address Port During read/write Command ............................................. 11-51
Register Settings (Bank-Based Interleaving) ...................................................................... 11-51
GPCM Interfaces Signals.................................................................................................... 11-52
GPCM Strobe Signal Behavior ........................................................................................... 11-53
TRLX and EHTR Combinations......................................................................................... 11-59
Boot Bank Field Values after Reset .................................................................................... 11-62
UPM Interfaces Signals ...................................................................................................... 11-63
UPM Routines Start Addresses........................................................................................... 11-66
RAM Word Bit Settings ...................................................................................................... 11-72
MxMR Loop Field Usage ................................................................................................... 11-77
UPM Address Multiplexing ................................................................................................ 11-78
60x Address Bus Partition................................................................................................... 11-81
DRAM Device Address Port during an activate command ................................................ 11-81
Register Settings ................................................................................................................. 11-81
UPMs Attributes Example .................................................................................................. 11-83
UPMs Attributes Example .................................................................................................. 11-91
EDO Connection Field Value Example .............................................................................. 11-93
TAP Signals........................................................................................................................... 13-2
Instruction Decoding............................................................................................................. 13-6
Possible MPC8280 Applications .......................................................................................... 14-3
Peripheral Prioritization ........................................................................................................ 14-7
RISC Controller Configuration Register Field Descriptions ................................................ 14-9
RTSCR Field Descriptions.................................................................................................. 14-11
RISC Microcode Revision Number .................................................................................... 14-12
CP Command Register Field Descriptions ......................................................................... 14-13
CP Command Opcodes ....................................................................................................... 14-14
Command Descriptions....................................................................................................... 14-15
Buffer Descriptor Format.................................................................................................... 14-21
Parameter RAM .................................................................................................................. 14-22
RISC Timer Table Parameter RAM .................................................................................... 14-24
TM_CMD Field Descriptions ............................................................................................. 14-25
SIx RAM Entry (MCC = 0) ................................................................................................ 15-11
SIx RAM Entry (MCC = 1) ................................................................................................ 15-13
SIx RAM Entry Descriptions.............................................................................................. 15-14
SIxGMR Field Descriptions................................................................................................ 15-17
SIxMR Field Descriptions .................................................................................................. 15-18
SIxRSR Field Descriptions ................................................................................................. 15-24
SIxCMDR Field Description .............................................................................................. 15-25
SIxSTR Field Descriptions ................................................................................................. 15-25
IDL Signal Descriptions...................................................................................................... 15-27
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
lxxi
Tables
Table
Number
15-10
15-11
15-12
16-1
16-2
16-3
16-4
16-5
16-6
16-7
17-1
17-2
17-3
18-1
18-2
18-3
18-4
19-1
19-2
19-3
19-4
19-5
19-6
19-7
19-8
19-9
19-10
19-11
19-12
19-13
19-14
19-15
19-16
19-17
20-1
20-2
20-3
20-4
20-5
20-6
20-7
Title
Page
Number
SIx RAM Entries for an IDL Interface ............................................................................... 15-29
GCI Signals ......................................................................................................................... 15-31
SIx RAM Entries for a GCI Interface (SCIT Mode) .......................................................... 15-33
Clock Source Options ........................................................................................................... 16-6
CMXUAR Field Descriptions............................................................................................... 16-7
CMXSI1CR Field Descriptions .......................................................................................... 16-12
CMXSI2CR Field Descriptions .......................................................................................... 16-13
CMXFCR Field Descriptions.............................................................................................. 16-14
CMXSCR Field Descriptions.............................................................................................. 16-16
CMXSMR Field Descriptions............................................................................................. 16-19
BRGCx Field Descriptions ................................................................................................... 17-3
BRG External Clock Source Options.................................................................................... 17-4
Typical Baud Rates for Asynchronous Communication....................................................... 17-5
TGCR1 Field Descriptions.................................................................................................... 18-4
TGCR2 Field Descriptions.................................................................................................... 18-5
TMR1–TMR4 Field Descriptions ......................................................................................... 18-6
TER Field Descriptions......................................................................................................... 18-8
SDSR Field Descriptions ...................................................................................................... 19-3
PDTEM and LDTEM Field Descriptions ............................................................................. 19-5
IDMA Transfer Parameters................................................................................................... 19-7
IDMAx Parameter RAM..................................................................................................... 19-16
DCM Field Descriptions ..................................................................................................... 19-18
IDMA Channel Data Transfer Operation............................................................................ 19-20
Valid Memory-to-Memory STS/DTS Values...................................................................... 19-21
Valid STS/DTS Values for Peripherals ............................................................................... 19-21
IDSR/IDMR Field Descriptions.......................................................................................... 19-23
IDMA BD Field Descriptions ............................................................................................. 19-24
IDMA Bus Exceptions ........................................................................................................ 19-27
Parallel I/O Register Programming—Port C ...................................................................... 19-28
Parallel I/O Register Programming—Port A ...................................................................... 19-28
Parallel I/O Register Programming—Port D ...................................................................... 19-29
Example: Peripheral-to-Memory Mode—IDMA2 ............................................................. 19-29
Example: Memory-to-Peripheral Fly-By Mode (on 60x)–IDMA3 .................................... 19-30
Programming Example: Memory-to-Memory (PCI-to-60x)—IDMA1.............................. 19-32
GSMR_H Field Descriptions ................................................................................................ 20-3
GSMR_L Field Descriptions ................................................................................................ 20-5
TODR Field Descriptions ................................................................................................... 20-10
SCC Parameter RAM Map for All Protocols...................................................................... 20-13
Parameter RAM—SCC Base Addresses............................................................................. 20-15
RFCRx /TFCRx Field Descriptions.................................................................................... 20-15
SCCx Event, Mask, and Status Registers ........................................................................... 20-16
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
lxxii
Freescale Semiconductor
Tables
Table
Number
20-8
20-9
21-1
21-2
21-3
21-4
21-5
21-6
21-7
21-8
21-9
21-10
21-11
21-12
21-13
21-14
22-1
22-2
22-3
22-4
22-5
22-6
22-7
22-8
22-9
22-10
23-1
23-2
23-3
23-4
23-5
23-6
23-7
23-8
23-9
23-10
23-11
23-12
23-13
23-14
23-15
Title
Page
Number
Preamble Requirements ...................................................................................................... 20-22
DPLL Codings .................................................................................................................... 20-24
UART-Specific SCC Parameter RAM Memory Map ........................................................... 21-4
Transmit Commands ............................................................................................................. 21-6
Receive Commands............................................................................................................... 21-6
Control Character Table, RCCM, and RCCR Descriptions.................................................. 21-8
TOSEQ Field Descriptions ................................................................................................. 21-10
DSR Fields Descriptions ..................................................................................................... 21-11
Transmission Errors ............................................................................................................ 21-12
Reception Errors ................................................................................................................. 21-12
PSMR UART Field Descriptions........................................................................................ 21-13
SCC UART RxBD Status and Control Field Descriptions ................................................. 21-17
SCC UART TxBD Status and Control Field Descriptions ................................................. 21-18
SCCE/SCCM Field Descriptions for UART Mode ........................................................... 21-21
UART SCCS Field Descriptions......................................................................................... 21-22
UART Control Characters for S-Records Example ............................................................ 21-24
HDLC-Specific SCC Parameter RAM Memory Map .......................................................... 22-3
Transmit Commands ............................................................................................................. 22-5
Receive Commands .............................................................................................................. 22-5
Transmit Errors ................................................................................................................... 22-6
Receive Errors....................................................................................................................... 22-6
PSMR HDLC Field Descriptions.......................................................................................... 22-7
SCC HDLC RxBD Status and Control Field Descriptions................................................... 22-9
SCC HDLC TxBD Status and Control Field Descriptions ................................................. 22-12
SCCE/SCCM Field Descriptions ....................................................................................... 22-13
HDLC SCCS Field Descriptions......................................................................................... 22-16
SCC BISYNC Parameter RAM Memory Map ..................................................................... 23-3
Transmit Commands ............................................................................................................. 23-5
Receive Commands............................................................................................................... 23-5
Control Character Table and RCCM Field Descriptions ...................................................... 23-7
BSYNC Field Descriptions ................................................................................................... 23-8
BDLE Field Descriptions...................................................................................................... 23-9
Receiver SYNC Pattern Lengths of the DSR........................................................................ 23-9
Transmit Errors ................................................................................................................... 23-10
Receive Errors..................................................................................................................... 23-10
PSMR Field Descriptions.................................................................................................... 23-11
SCC BISYNC RxBD Status and Control Field Descriptions ............................................. 23-12
SCC BISYNC TxBD Status and Control Field Descriptions ............................................. 23-14
SCCE/SCCM Field Descriptions ........................................................................................ 23-16
SCCS Field Descriptions .................................................................................................... 23-17
Control Characters .............................................................................................................. 23-18
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
lxxiii
Tables
Table
Number
24-1
24-2
24-3
24-4
24-5
24-6
24-7
24-8
24-9
24-10
25-1
25-2
25-3
25-4
25-5
25-6
25-7
25-8
25-9
27-1
27-2
27-3
27-4
27-5
27-6
27-7
27-8
27-9
27-10
27-11
27-12
27-13
27-14
27-15
27-16
27-17
27-18
27-19
27-20
27-21
28-1
Title
Page
Number
Receiver SYNC Pattern Lengths of the DSR........................................................................ 24-3
SCC Transparent Parameter RAM Memory Map................................................................. 24-6
Transmit Commands ............................................................................................................. 24-6
Receive Commands............................................................................................................... 24-7
Transmit Errors ..................................................................................................................... 24-7
Receive Errors....................................................................................................................... 24-8
SCC Transparent RxBD Status and Control Field Descriptions........................................... 24-9
SCC Transparent TxBD Status and Control Field Descriptions ......................................... 24-10
SCCE/SCCM Field Descriptions ....................................................................................... 24-11
SCCS Field Descriptions .................................................................................................... 24-12
SCC Ethernet Parameter RAM Memory Map ...................................................................... 25-7
Transmit Commands ........................................................................................................... 25-10
Receive Commands............................................................................................................. 25-10
Transmission Errors ............................................................................................................ 25-13
Reception Errors ................................................................................................................. 25-14
PSMR Field Descriptions.................................................................................................... 25-15
SCC Ethernet RxBD Status and Control Field Descriptions .............................................. 25-16
SCC Ethernet TxBD Status and Control Field Descriptions .............................................. 25-19
SCCE/SCCM Field Descriptions ........................................................................................ 25-20
USB Pins Functions .............................................................................................................. 27-3
USB Tokens .......................................................................................................................... 27-6
USB Tokens ........................................................................................................................ 27-10
USB Parameter RAM Memory Map .................................................................................. 27-12
Endpoint Parameter Block .................................................................................................. 27-13
FRAME_N Field Descriptions............................................................................................ 27-15
FRAME_N Field Descriptions............................................................................................ 27-16
RFCR and TFCR Fields...................................................................................................... 27-16
USMOD Fields ................................................................................................................... 27-17
USADR Fields .................................................................................................................... 27-18
USEPx Field Descriptions .................................................................................................. 27-18
USCOM Fields.................................................................................................................... 27-20
USBER Fields ..................................................................................................................... 27-21
USBS Fields ........................................................................................................................ 27-22
USSFT Fields ...................................................................................................................... 27-22
USB Rx BD Fields .............................................................................................................. 27-24
USB Function Tx BD Fields ............................................................................................... 27-26
USB Host Tx BD Fields...................................................................................................... 27-28
USB Host TrBD Fields ....................................................................................................... 27-30
USB Controller Transmission Errors .................................................................................. 27-33
USB Controller Reception Errors ....................................................................................... 27-33
SMCMR1/SMCMR2 Field Descriptions.............................................................................. 28-3
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
lxxiv
Freescale Semiconductor
Tables
Table
Number
28-2
28-3
28-4
28-5
28-6
28-7
28-8
28-9
28-10
28-11
28-12
28-13
28-14
28-15
28-16
28-17
28-18
28-19
28-20
28-21
28-22
28-23
29-1
29-2
29-3
29-4
29-5
29-6
29-7
29-8
29-9
29-10
29-11
29-12
29-13
29-14
29-15
29-16
29-17
29-18
29-19
Title
Page
Number
SMC UART and Transparent Parameter RAM Memory Map ............................................. 28-6
RFCR/TFCR Field Descriptions ........................................................................................... 28-8
Transmit Commands ........................................................................................................... 28-12
Receive Commands............................................................................................................. 28-12
SMC UART Errors.............................................................................................................. 28-13
SMC UART RxBD Field Descriptions ............................................................................... 28-14
SMC UART TxBD Field Descriptions ............................................................................... 28-17
SMCE/SMCM Field Descriptions ...................................................................................... 28-18
SMC Transparent Transmit Commands.............................................................................. 28-25
SMC Transparent Receive Commands ............................................................................... 28-25
SMC Transparent Error Conditions .................................................................................... 28-25
SMC Transparent RxBD Field Descriptions....................................................................... 28-26
SMC Transparent TxBD ..................................................................................................... 28-27
SMC Transparent TxBD Field Descriptions....................................................................... 28-27
SMCE/SMCM Field Descriptions ...................................................................................... 28-28
SMC GCI Parameter RAM Memory Map.......................................................................... 28-30
SMC GCI Commands ......................................................................................................... 28-32
SMC Monitor Channel RxBD Field Descriptions .............................................................. 28-32
SMC Monitor Channel TxBD Field Descriptions .............................................................. 28-33
SMC C/I Channel RxBD Field Descriptions ...................................................................... 28-34
SMC C/I Channel TxBD Field Descriptions ...................................................................... 28-34
SMCE/SMCM Field Descriptions ...................................................................................... 28-35
Global MCC Parameters ....................................................................................................... 29-4
Channel-Specific Parameters for HDLC............................................................................... 29-6
TSTATE High-Byte Field Descriptions ................................................................................ 29-7
CHAMR Field Descriptions.................................................................................................. 29-9
RSTATE High-Byte Field Descriptions .............................................................................. 29-10
Channel-Specific Parameters for Transparent Operation.................................................... 29-11
CHAMR Field Descriptions—Transparent Mode .............................................................. 29-13
CES-Specific Global MCC Parameters .............................................................................. 29-14
CHAMR Field Descriptions—CES Mode.......................................................................... 29-15
Channel-Specific Parameters for SS7 ................................................................................. 29-18
ECHAMR Fields Description ............................................................................................. 29-21
Parameter Values for SUERM in Japanese SS7.................................................................. 29-23
SS7 Configuration Register Fields Description .................................................................. 29-23
Channel Extra Parameters ................................................................................................... 29-27
MCCF Field Descriptions ................................................................................................... 29-32
Group Channel Assignments .............................................................................................. 29-33
MCC Commands................................................................................................................. 29-34
MCCE/MCCM Register Field Descriptions ....................................................................... 29-36
Interrupt Circular Table Entry Field Descriptions .............................................................. 29-37
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
lxxv
Tables
Table
Number
29-20
29-21
29-22
30-1
30-2
30-3
30-4
30-5
30-6
31-1
31-2
31-3
31-4
31-5
31-6
31-7
31-8
31-9
31-10
31-11
31-12
31-13
31-14
31-15
31-16
31-17
31-18
31-19
31-20
31-21
31-22
31-23
31-24
31-25
31-26
31-27
31-28
31-29
31-30
31-31
31-32
Title
Page
Number
GUN Error Recovery .......................................................................................................... 29-41
RxBD Field Descriptions .................................................................................................... 29-42
TxBD Field Descriptions .................................................................................................... 29-44
Internal Clocks to CPM Clock Frequency Ratio .................................................................. 30-3
GFMR Register Field Descriptions....................................................................................... 30-4
GFEMRx Field Descriptions ................................................................................................ 30-8
FTODR Field Descriptions ................................................................................................. 30-10
FCC Parameter RAM Common to All Protocols Except ATM .......................................... 30-12
FCRx Field Descriptions..................................................................................................... 30-14
ATM Service Types............................................................................................................... 31-9
External CAM Input and Output Field Descriptions .......................................................... 31-14
Field Descriptions for Address Compression ..................................................................... 31-16
VCOFFSET Calculation Examples for Contiguous VCLTs ............................................... 31-16
VP-Level Table Entry Address Calculation Example......................................................... 31-17
VC-Level Table Entry Address Calculation Example ........................................................ 31-17
Fields and their Positions in RM Cells................................................................................ 31-26
Pre-Assigned Header Values at the UNI ............................................................................. 31-27
Pre-Assigned Header Values at the NNI ............................................................................. 31-28
Performance Monitoring Cell Fields................................................................................... 31-30
ATM Parameter RAM Map................................................................................................. 31-36
UEAD_OFFSETs for Extended Addresses in the UDC Extra Header ............................... 31-39
VCI Filtering Enable Field Descriptions ............................................................................ 31-39
GMODE Field Descriptions................................................................................................ 31-40
Receive and Transmit Connection Table Sizes ................................................................... 31-41
RCT Field Descriptions ...................................................................................................... 31-44
RCT Settings (AAL5 Protocol-Specific) ............................................................................ 31-46
ABR Protocol-Specific RCT Field Descriptions ................................................................ 31-47
AAL1 Protocol-Specific RCT Field Descriptions .............................................................. 31-48
AAL0-Specific RCT Field Descriptions............................................................................. 31-49
TCT Field Descriptions....................................................................................................... 31-51
AAL5-Specific TCT Field Descriptions ............................................................................. 31-53
AAL1 Protocol-Specific TCT Field Descriptions .............................................................. 31-54
AAL0-Specific TCT Field Descriptions ............................................................................. 31-55
VBR-Specific TCTE Field Descriptions............................................................................. 31-56
UBR+ Protocol-Specific TCTE Field Descriptions............................................................ 31-57
ABR-Specific TCTE Field Descriptions............................................................................. 31-58
OAM—Performance Monitoring Table Field Descriptions ............................................... 31-61
APC Parameter Table.......................................................................................................... 31-62
APC Priority Table Entry.................................................................................................... 31-63
Control Slot Field Description ............................................................................................ 31-64
Free Buffer Pool Entry Field Descriptions.......................................................................... 31-68
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
lxxvi
Freescale Semiconductor
Tables
Table
Number
31-33
31-34
31-35
31-36
31-37
31-38
31-39
31-40
31-41
31-42
31-43
31-44
31-45
31-46
31-47
31-48
31-49
31-50
31-51
31-52
31-53
31-54
32-1
32-2
32-3
32-4
32-5
32-6
32-7
32-8
32-9
32-10
32-11
32-12
32-13
32-14
32-15
33-1
33-2
33-3
33-4
Title
Page
Number
Free Buffer Pool Parameter Table....................................................................................... 31-68
Receive and Transmit Buffers............................................................................................. 31-69
AAL5 RxBD Field Descriptions......................................................................................... 31-70
AAL1 RxBD Field Descriptions......................................................................................... 31-71
AAL0 RxBD Field Descriptions......................................................................................... 31-72
AAL5 TxBD Field Descriptions ......................................................................................... 31-74
AAL1 TxBD Field Descriptions ......................................................................................... 31-75
AAL0 TxBD Field Descriptions ......................................................................................... 31-76
UNI Statistics Table ............................................................................................................ 31-78
Interrupt Queue Entry Field Description ............................................................................ 31-80
Interrupt Queue Parameter Table ........................................................................................ 31-81
UTOPIA Master Mode Signal Descriptions ....................................................................... 31-82
UTOPIA Slave Mode Signals ............................................................................................. 31-83
UTOPIA Loop-Back Modes ............................................................................................... 31-85
FCC ATM Mode Register (FPSMR) .................................................................................. 31-86
FCCE/FCCM Field Descriptions ........................................................................................ 31-89
COMM_INFO Field Descriptions ...................................................................................... 31-90
FTIRRx Field Descriptions................................................................................................. 31-92
FIRPERx Field Descriptions (TIREM=1) .......................................................................... 31-94
FIRERx Field Descriptions (TIREM=1)............................................................................. 31-95
IRSRx_HI Field Descriptions (TIREM=1)......................................................................... 31-96
FIRSRx_LO Field Descriptions (TIREM=1) ..................................................................... 31-97
CAS Routing Table Entry Field Descriptions..................................................................... 32-13
CES Adaptive Threshold Table Field Descriptions ............................................................ 32-17
AAL1 CES Field Descriptions............................................................................................ 32-22
AAL1 CES Parameters ....................................................................................................... 32-25
RCT Field Descriptions ...................................................................................................... 32-27
AAL1 CES Protocol-Specific RCT Field Descriptions ...................................................... 32-29
TCT Field Descriptions....................................................................................................... 32-32
AAL1 CES Protocol-Specific TCT Field Descriptions ...................................................... 32-35
OCASSR Field Descriptions............................................................................................... 32-36
Receive and Transmit Buffers............................................................................................. 32-38
AAL1 CES RxBD Field Descriptions ................................................................................ 32-39
AAL1 CES TxBD Field Descriptions................................................................................. 32-40
AAL1 CES Interrupt Queue Entry Field Descriptions ....................................................... 32-41
AAL1 CES DPR Statistics Table ........................................................................................ 32-43
AAL1 CES External Statistics Table .................................................................................. 32-44
AAL2 Protocol-Specific Transmit Connection Table (TCT) Field Descriptions ................. 33-9
CPS TxQD Field Descriptions............................................................................................ 33-13
CPS TxBD Field Descriptions ............................................................................................ 33-15
SSSAR TxQD Field Descriptions....................................................................................... 33-17
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
lxxvii
Tables
Table
Number
33-5
33-6
33-7
33-8
33-9
33-10
33-11
33-12
33-13
33-14
33-15
34-1
34-2
34-3
34-4
34-5
34-6
34-7
34-8
34-9
34-10
34-11
34-12
34-13
34-14
34-15
34-16
34-17
34-18
34-19
34-20
34-21
34-22
34-23
34-24
34-25
34-26
34-27
34-28
34-29
35-1
Title
Page
Number
SSSAR TxBD Field Descriptions ....................................................................................... 33-18
AAL2 Protocol-Specific RCT Field Descriptions .............................................................. 33-23
CPS RxQD Field Descriptions............................................................................................ 33-27
CPS RxBD Field Descriptions............................................................................................ 33-28
CPS Switch RxQD Field Descriptions................................................................................ 33-29
Switch RxBD Field Descriptions........................................................................................ 33-30
SSSAR RxQD Field Descriptions....................................................................................... 33-31
SSSAR RxBD Field Descriptions....................................................................................... 33-33
AAL2 Parameter RAM ....................................................................................................... 33-34
AAL2 Interrupt Queue Entry CID ≠ 0 Field Descriptions.................................................. 33-38
AAL2 Interrupt Queue Entry CID = 0 Field Descriptions.................................................. 33-39
IMA Sublayer in Layer Reference Model............................................................................. 34-2
FCC Parameter RAM Additions ......................................................................................... 34-22
IMA Root Table .................................................................................................................. 34-23
IMACNTL Field Descriptions ............................................................................................ 34-25
IMA Group Transmit Table Entry ...................................................................................... 34-25
IGTCNTL Field Descriptions ............................................................................................. 34-27
IGTSTATE Field Descriptions ............................................................................................ 34-28
Transmit Group Order Table Entry Field Descriptions....................................................... 34-28
ICP Cell Template .............................................................................................................. 34-29
IMA Group Receive Table Entry ....................................................................................... 34-31
IGRCNTL Field Descriptions ............................................................................................. 34-34
IGRSTATE Field Descriptions............................................................................................ 34-35
IRGFS Field Descriptions ................................................................................................... 34-35
Receive Group Order Table Entry Field Descriptions ........................................................ 34-36
IMA Link Transmit Table Entry ........................................................................................ 34-36
ILTCNTL Field Descriptions .............................................................................................. 34-38
ILTSTATE Field Descriptions............................................................................................. 34-38
ITINTSTAT Field Descriptions........................................................................................... 34-39
IMA Link Receive Table Entry........................................................................................... 34-40
ILRCNTL Field Descriptions ............................................................................................. 34-41
ILRSTATE Field Descriptions ............................................................................................ 34-42
IMA Link Receive Statistics Table Entry ........................................................................... 34-43
IMA Interrupt Queue Entry Field Descriptions .................................................................. 34-46
Unavailable Features when DREQx used as IDCR Master Clock ..................................... 34-48
IDCR IMA Root Parameters............................................................................................... 34-49
IDCR Table Entry ............................................................................................................... 34-49
IDSR/IDMR Field Descriptions.......................................................................................... 34-50
Examples of APC Programming for IMA .......................................................................... 34-51
COMM_INFO Field Descriptions ...................................................................................... 34-53
TC Layer Signals .................................................................................................................. 35-6
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
lxxviii
Freescale Semiconductor
Tables
Table
Number
35-2
35-3
35-4
35-5
35-6
35-7
35-8
35-9
35-10
35-11
35-12
36-1
36-2
36-3
36-4
36-5
36-6
36-7
36-8
36-9
36-10
36-11
37-1
37-2
37-3
37-4
37-5
37-6
37-7
37-8
37-9
37-10
39-1
39-2
39-3
39-4
39-5
39-6
39-7
39-8
39-9
Title
Page
Number
TCMODEx Field Descriptions.............................................................................................. 35-7
CDSMRx Field Descriptions ................................................................................................ 35-9
TCERx Field Descriptions .................................................................................................... 35-9
TCGER Field Descriptions ................................................................................................. 35-10
TCGSR Field Descriptions ................................................................................................. 35-11
Programming GFMR and FPSMR to Setup the FCC2 ....................................................... 35-16
Enable FCC2 ....................................................................................................................... 35-16
Programming the CPM MUX for a TI Application............................................................ 35-16
Programming the TC Layer Block...................................................................................... 35-17
Programming the SI RAM (Rx or Tx) for a T1 Application .............................................. 35-17
Programming SI Registers to Enable TDM ........................................................................ 35-17
Flow Control Frame Structure .............................................................................................. 36-7
Ethernet-Specific Parameter RAM ....................................................................................... 36-9
Transmit Commands ........................................................................................................... 36-13
Receive Commands............................................................................................................. 36-13
RMON Statistics and Counters ........................................................................................... 36-14
Transmission Errors ............................................................................................................ 36-19
Reception Errors ................................................................................................................. 36-19
FPSMR Ethernet Field Descriptions................................................................................... 36-20
FCCE/FCCM Field Descriptions ........................................................................................ 36-22
RxBD Field Descriptions .................................................................................................... 36-24
Ethernet TxBD Field Definitions........................................................................................ 36-27
FCC HDLC-Specific Parameter RAM Memory Map .......................................................... 37-3
Transmit Commands ............................................................................................................. 37-5
Receive Commands............................................................................................................... 37-6
HDLC Transmission Errors .................................................................................................. 37-6
HDLC Reception Errors ....................................................................................................... 37-7
FPSMR Field Descriptions .................................................................................................. 37-8
RxBD field Descriptions ..................................................................................................... 37-11
HDLC TxBD Field Descriptions ....................................................................................... 37-13
FCCE/FCCM Field Descriptions ........................................................................................ 37-15
FCCS Register Field Descriptions ...................................................................................... 37-17
SPMODE Field Descriptions ................................................................................................ 39-6
Example Conventions ........................................................................................................... 39-8
SPIE/SPIM Field Descriptions.............................................................................................. 39-9
SPCOM Field Descriptions................................................................................................. 39-10
SPI Parameter RAM Memory Map .................................................................................... 39-11
RFCR/TFCR Field Descriptions ......................................................................................... 39-12
SPI Commands.................................................................................................................... 39-12
SPI RxBD Status and Control Field Descriptions............................................................... 39-14
SPI TxBD Status and Control Field Descriptions............................................................... 39-15
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
lxxix
Tables
Table
Number
40-1
40-2
40-3
40-4
40-5
40-6
40-7
40-8
40-9
40-10
41-1
41-2
41-3
41-4
41-5
41-6
41-7
41-8
Title
Page
Number
II2MOD Field Descriptions .................................................................................................. 40-6
I2ADD Field Descriptions .................................................................................................... 40-7
I2BRG Field Descriptions..................................................................................................... 40-7
I2CER/I2CMR Field Descriptions........................................................................................ 40-8
I2COM Field Descriptions.................................................................................................... 40-9
I2C Parameter RAM Memory Map....................................................................................... 40-9
RFCR/TFCR Field Descriptions ......................................................................................... 40-11
I2C Transmit/Receive Commands....................................................................................... 40-11
I2C RxBD Status and Control Bits...................................................................................... 40-13
I2C TxBD Status and Control Bits...................................................................................... 40-14
PODRx Field Descriptions ................................................................................................... 41-2
PDIR Field Descriptions ....................................................................................................... 41-3
PPAR Field Descriptions....................................................................................................... 41-4
PSORx Field Descriptions .................................................................................................... 41-5
Port A—Dedicated Pin Assignment (PPARA = 1) ............................................................... 41-8
Port B Dedicated Pin Assignment (PPARB = 1) ................................................................ 41-12
Port C Dedicated Pin Assignment (PPARC = 1) ................................................................ 41-15
Port D Dedicated Pin Assignment (PPARD = 1) .............................................................. 41-17
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
lxxx
Freescale Semiconductor
About This Book
The MPC8280 is a versatile communications processor that integrates on one chip a high-performance
PowerPC™ RISC microprocessor, a very flexible system integration unit, and many communications
peripheral controllers that can be used in a variety of applications, particularly in communications and
networking systems.
The primary objective of this manual is to help communications system designers build systems using any
member of the MPC8280 PowerQUICC II™ family of communications processors and to help software
designers provide operating systems and user-level applications to take complete advantage of the
MPC8280.
NOTE: Devices Supported by This Manual
This manual supports the MPC8280, the MPC8275, and the MPC8270,
which are collectively called either the MPC8280 or the PowerQUICC II
throughout this manual. Device numbers are cited only if information does
not pertain to all devices.
Although this book describes aspects of the PowerPC architecture that are critical for understanding the
MPC8280 core, it does not contain a complete description of the architecture. Where additional
information might help the reader, references are made to Programming Environments Manual for 32-Bit
Implementation of the PowerPC Architecture, Rev. 2. Refer to “Architecture Documentation” for ordering
information.
The information in this book is subject to change without notice, as described in the disclaimers on the title
page of this book. As with any technical documentation, it is the readers’ responsibility to use the most
recent version of the documentation. For more information, contact your sales representative.
Before Using this Manual—Important Note
Before using this manual, determine whether it is the latest revision and if there are errata or addenda. To
locate any published errata or updates for this document, refer to the worldwide web at
www.freescale.com.
Audience
This manual is intended for software and hardware developers and application programmers who want to
develop products for the MPC8280. It is assumed that the reader has a basic understanding of computer
networking, OSI layers, RISC architecture, and communications protocols described herein. Where
useful, additional sources provide in-depth discussions of such topics.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
lxxxi
Organization
Following is a summary and a brief description of the chapters of this manual:
• Part I, “Overview,” provides a high-level description of the MPC8280, describing general
operation and listing basic features.
— Chapter 1, “Overview,” provides a high-level description of MPC8280 functions and features.
It roughly follows the structure of this book, summarizing the relevant features and providing
references for the reader who needs additional information.
— Chapter 2, “G2_LE Core,” provides an overview of the MPC8280 core, summarizing topics
described in further detail in subsequent chapters.
— Chapter 3, “Memory Map,” presents a table showing where MPC8280 registers are mapped in
memory. It includes cross references that indicate where the registers are described in detail.
• Part II, “Configuration and Reset,” describes start-up behavior of the MPC8280.
— Chapter 4, “System Interface Unit (SIU),” describes the system configuration and protection
functions that provide various monitors and timers, and the 60x bus configuration.
— Chapter 5, “Reset,” describes the behavior of the MPC8280 at reset and start-up.
• Part III, “The Hardware Interface,” describes external signals, clocking, memory control, and
power management of the MPC8280.
— Chapter 6, “External Signals,” shows a functional pinout of the MPC8280 and describes the
MPC8280 signals.
— Chapter 7, “60x Signals,” describes signals on the 60x bus.
— Chapter 8, “The 60x Bus,” describes the operation of the bus used by processors that
implement the PowerPC architecture.
— Chapter 9, “PCI Bridge,” describes how the PCI bridge enables the MPC8280 to gluelessly
bridge PCI agents to a host processor that implements the PowerPC architecture and how it is
compliant with PCI Specification Revision 2.2.
— Chapter 10, “Clocks and Power Control,” describes the clocking architecture of the MPC8280.
— Chapter 11, “Memory Controller,” describes the memory controller, which controls a
maximum of eight memory banks shared among a general-purpose chip-select machine
(GPCM) and three user-programmable machines (UPMs).
— Chapter 12, “Secondary (L2) Cache Support,” provides information about implementation and
configuration of a level-2 cache.
— Chapter 13, “IEEE 1149.1 Test Access Port,” describes the dedicated user-accessible test
access port (TAP), which is fully compatible with the IEEE 1149.1 Standard Test Access Port
and Boundary Scan Architecture.
• Part IV, “Communications Processor Module,” describes the configuration, clocking, and
operation of the various communications protocols that the MPC8280 supports.
— Chapter 14, “Communications Processor Module Overview,” provides a brief overview of the
CPM.
— Chapter 15, “Serial Interface with Time-Slot Assigner,” describes the SIU, which controls
system start-up, initialization and operation, protection, as well as the external system bus.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
lxxxii
Freescale Semiconductor
— Chapter 16, “CPM Multiplexing,” describes the CPM multiplexing logic (CMX) that connects
the physical layer—UTOPIA, MII, modem lines.
— Chapter 17, “Baud-Rate Generators (BRGs),” describes the eight independent, identical
baud-rate generators (BRGs) that can be used with the FCCs, SCCs, and SMCs.
— Chapter 18, “Timers,” describes the timer implementation, which can be configured as four
identical 16-bit or two 32-bit general-purpose timers.
— Chapter 19, “SDMA Channels and IDMA Emulation,” describes the two physical serial DMA
(SDMA) channels on the MPC8280.
— Chapter 20, “Serial Communications Controllers (SCCs),” describes the four serial
communications controllers (SCC), which can be configured independently to implement
different protocols for bridging functions, routers, and gateways, and to interface with a wide
variety of standard WANs, LANs, and proprietary networks.
— Chapter 21, “SCC UART Mode,” describes the MPC8280 implementation of universal
asynchronous receiver transmitter (UART) protocol that sends low-speed data between
devices.
— Chapter 22, “SCC HDLC Mode,” describes the MPC8280 implementation of HDLC protocol.
— Chapter 23, “SCC BISYNC Mode,” describes the MPC8280 implementation of byte-oriented
BISYNC protocol developed by IBM for use in networking products.
— Chapter 24, “SCC Transparent Mode,” describes the MPC8280 implementation of transparent
mode (also called totally transparent mode), which provides a clear channel on which the SCC
can send or receive serial data without bit-level manipulation.
— Chapter 25, “SCC Ethernet Mode,” describes the MPC8280 implementation of Ethernet
protocol.
— Chapter 26, “SCC AppleTalk Mode,” describes the MPC8280 implementation of AppleTalk.
— Chapter 27, “Universal Serial Bus Controller,” describes the MPC8280’s USB controller,
including basic operation, the parameter RAM, and registers.
— Chapter 28, “Serial Management Controllers (SMCs),” describes two serial management
controllers, full-duplex ports that can be configured independently to support one of three
protocols—UART, transparent, or general-circuit interface (GCI).
— Chapter 29, “Multi-Channel Controllers (MCCs),” describes the MPC8280’s multi-channel
controller (MCC), which handles up to 128 serial, full-duplex data channels.
— Chapter 30, “Fast Communications Controllers (FCCs),” describes the MPC8280’s fast
communications controllers (FCCs), which are SCCs optimized for synchronous high-rate
protocols.
— Chapter 31, “ATM Controller and AAL0, AAL1, and AAL5,” describes the MPC8280 ATM
controller, which provides the ATM and AAL layers of the ATM protocol. The ATM controller
performs segmentation and reassembly (SAR) functions of AAL5, AAL1, and AAL0, and
most of the common parts convergence sublayer (CP-CS) of these protocols.
— Chapter 32, “ATM AAL1 Circuit Emulation Service,” describes the implementation of circuit
emulation service (CES) using ATM adaptation layer type 1 (AAL1) on the MPC8280.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
lxxxiii
•
•
•
— Chapter 33, “ATM AAL2,” describes the functionality and data structures of ATM adaptation
layer type 2 (AAL2) CPS, CPS switching, and SSSAR.
— Chapter 34, “Inverse Multiplexing for ATM (IMA),” describes specifications for the inverse
multiplexing for ATM (IMA) microcode.
— Chapter 35, “ATM Transmission Convergence Layer,” describes how the MPC8280 can
support applications that receive ATM traffic over the standard serial protocols like E1, T1, and
xDSL via its serial interface (SIx TDMx and NMSI) ports because of its internally
implemented TC-layer functionality.
— Chapter 36, “Fast Ethernet Controller,” describes the MPC8280’s implementation of the
Ethernet IEEE 802.3 protocol.
— Chapter 37, “FCC HDLC Controller,” describes the FCC implementation of the HDLC
protocol.
— Chapter 38, “FCC Transparent Controller,” describes the FCC implementation of the
transparent protocol.
— Chapter 39, “Serial Peripheral Interface (SPI),” describes the serial peripheral interface, which
allows the MPC8280 to exchange data between other PowerQUICC II chips, the MC68360, the
MC68302, the M68HC11, and M68HC05 microcontroller families, and peripheral devices
such as EEPROMs, real-time clocks, A/D converters, and ISDN devices.
— Chapter 40, “I2C Controller,” describes the MPC8280 implementation of the inter-integrated
circuit (I2C®) controller, which allows data to be exchanged with other I2C devices, such as
microcontrollers, EEPROMs, real-time clock devices, and A/D converters.
— Chapter 41, “Parallel I/O Ports,” describes the four general-purpose I/O ports A–D. Each
signal in the I/O ports can be configured as a general-purpose I/O signal or as a signal dedicated
to supporting communications devices, such as SMCs, SCCs. MCCs, and FCCs.
Appendix A, “Register Quick Reference Guide,” provides a quick reference to the registers
incorporated in the G2_LE core.
Appendix B, “Revision History,” provides a list of the major differences between revisions of the
MPC8280 PowerQUICC II Family Reference Manual.
This book also includes an index and a glossary.
Suggested Reading
This section lists additional reading that provides background for the information in this manual as well as
general information about the PowerPC architecture.
MPC82xx Documentation
Supporting documentation for the MPC8280 can be accessed through the world-wide web at
www.freescale.com. This documentation includes technical specifications, reference materials, and
detailed applications notes.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
lxxxiv
Freescale Semiconductor
Architecture Documentation
Architecture documentation is organized in the following types of documents:
• Manuals—These books provide details about individual implementations of the PowerPC
architecture and are intended to be used with the Programming Environments Manual. These
include the G2 Core Reference Manual (Freescale order #: G2CORERM).
• Programming environments manuals—These books provide information about resources defined by
the PowerPC architecture that are common to processors that implement the PowerPC architecture. The
two versions include one that describes the functionality of the combined 32- and 64-bit architecture
models and one that describes only the 32-bit model. The MPC8280 adheres to the 32-bit architecture
definition.
— Programming Environments Manual for 32-Bit Implementations of the PowerPC Architecture
(Freescale order #: MPCFPE32B)
• The Programmer’s Pocket Reference Guide for the PowerPC Architecture:
MPCPRGREF/D—This guide provides an overview of registers, instructions, and exceptions for
32-bit implementations.
• Application notes—These short documents contain useful information about specific design issues
useful to programmers and engineers working with Freescale’s processors.
For a current list of documentation, refer to www.freescale.com.
Conventions
This document uses the following notational conventions:
Table 1:
Bold entries in figures and tables showing registers and parameter RAM should
be initialized by the user.
B ld
mnemonics
Instruction mnemonics are shown in lowercase bold.
italics
Italics indicate variable command parameters, for example, bcctrx.
Book titles in text are set in italics.
0x0
Prefix to denote hexadecimal number
0b0
Prefix to denote binary number
rA, rB
Instruction syntax used to identify a source GPR
rD
Instruction syntax used to identify a destination GPR
REG[FIELD]
Abbreviations or acronyms for registers or buffer descriptors are shown in
uppercase text. Specific bits, fields, or numerical ranges appear in brackets. For
example, MSR[LE] refers to the little-endian mode enable bit in the machine state
register.
x
In certain contexts, such as in a signal encoding or a bit field, indicates a don’t
care.
n
Used to express an undefined numerical value
¬
NOT logical operator
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
lxxxv
&
|
AND logical operator
OR logical operator
Acronyms and Abbreviations
Table i contains acronyms and abbreviations used in this document. Note that the meanings for some
acronyms (such as SDR1 and DSISR) are historical, and the words for which an acronym stands may not
be intuitively obvious.
Table i. Acronyms and Abbreviated Terms
Term
Meaning
A/D
Analog-to-digital
ALU
Arithmetic logic unit
ATM
Asynchronous transfer mode
BD
Buffer descriptor
BIST
Built-in self test
BPU
Branch processing unit
BRI
Basic rate interface.
BUID
Bus unit ID
CAM
Content-addressable memory
CEPT
Conference des administrations Europeanes des Postes et Telecommunications (European
Conference of Postal and Telecommunications Administrations).
CMX
CPM multiplexing logic
CPM
Communication processor module
CR
Condition register
CRC
Cyclic redundancy check
CTR
Count register
DABR
Data address breakpoint register
DAR
Data address register
DEC
Decrementer register
DMA
Direct memory access
DPLL
Digital phase-locked loop
DRAM
Dynamic random access memory
DSISR
Register used for determining the source of a DSI exception
DTLB
Data translation lookaside buffer
EA
Effective address
EEST
Enhanced Ethernet serial transceiver
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
lxxxvi
Freescale Semiconductor
Table i. Acronyms and Abbreviated Terms (continued)
Term
Meaning
EPROM
Erasable programmable read-only memory
FPR
Floating-point register
FPSCR
Floating-point status and control register
FPU
Floating-point unit
GCI
General circuit interface
GPCM
General-purpose chip-select machine
GPR
General-purpose register
GUI
Graphical user interface
HDLC
High-level data link control
I2C
Inter-integrated circuit
IDL
Inter-chip digital link
IEEE
Institute of Electrical and Electronics Engineers
IrDA
Infrared Data Association
ISDN
Integrated services digital network
ITLB
Instruction translation lookaside buffer
IU
Integer unit
JTAG
Joint Test Action Group
LIFO
Last-in-first-out
LR
Link register
LRU
Least recently used
LSB
Least-significant byte
lsb
Least-significant bit
LSU
Load/store unit
MAC
Multiply accumulate
MESI
Modified/exclusive/shared/invalid—cache coherency protocol
MMU
Memory management unit
MSB
Most-significant byte
msb
Most-significant bit
MSR
Machine state register
NaN
Not a number
NIA
Next instruction address
NMSI
Nonmultiplexed serial interface
No-op
No operation
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
lxxxvii
Table i. Acronyms and Abbreviated Terms (continued)
Term
Meaning
OEA
Operating environment architecture
OSI
Open systems interconnection
PCI
Peripheral component interconnect
PCMCIA
Personal Computer Memory Card International Association
PIR
Processor identification register
PRI
Primary rate interface
PVR
Processor version register
RISC
Reduced instruction set computing
RTOS
Real-time operating system
RWITM
Read with intent to modify
Rx
Receive
SCC
Serial communication controller
SCP
Serial control port
SDLC
Synchronous data link control
SDMA
Serial DMA
SI
Serial interface
SIMM
Signed immediate value
SIU
System interface unit
SMC
Serial management controller
SNA
Systems network architecture
SPI
Serial peripheral interface
SPR
Special-purpose register
SPRG n
Registers available for general purposes
SRAM
Static random access memory
SRR0
Machine status save/restore register 0
SRR1
Machine status save/restore register 1
TAP
Test access port
TB
Time base register
TDM
Time-division multiplexed
TLB
Translation lookaside buffer
TSA
Time-slot assigner
Tx
Transmit
UART
Universal asynchronous receiver/transmitter
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
lxxxviii
Freescale Semiconductor
Table i. Acronyms and Abbreviated Terms (continued)
Term
Meaning
UIMM
Unsigned immediate value
UISA
User instruction set architecture
UPM
User-programmable machine
USART
Universal synchronous/asynchronous receiver/transmitter
USB
Universal serial bus
VA
Virtual address
VEA
Virtual environment architecture
XER
Register used primarily for indicating conditions such as carries and overflows for integer operations
PowerPC Architecture Terminology Conventions
Table ii lists certain terms used in this manual that differ from the architecture terminology conventions.
Table ii. Terminology Conventions
The Architecture Specification
Data storage interrupt (DSI)
Extended mnemonics
Interrupt
ISI exception
Exception
Privileged mode (or privileged state)
Problem mode (or problem state)
Relocation
DSI exception
Simplified mnemonics
Instruction storage interrupt (ISI)
Real address
This Manual
Supervisor-level privilege
User-level privilege
Physical address
Translation
Storage (locations)
Memory
Storage (the act of)
Access
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
lxxxix
Table iii describes instruction field notation conventions used in this manual.
Table iii. Instruction Field Conventions
The Architecture Specification
BA, BB, BT
BF, BFA
Equivalent to:
crbA, crbB, crbD (respectively)
crfD, crfS (respectively)
D
d
DS
ds
FLM
FM
FXM
CRM
RA, RB, RT, RS
rA, rB, rD, rS (respectively)
SI
SIMM
U
IMM
UI
UIMM
/, //, ///
0...0 (shaded)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
xc
Freescale Semiconductor
Part I
Overview
Intended Audience
Part I is intended for readers who need a high-level understanding of the MPC8280.
Contents
Part I provides a high-level description of the MPC8280, describing general operation and listing basic
features.
• Chapter 1, “Overview,” provides a high-level description of MPC8280 functions and features. It
roughly follows the structure of this book, summarizing the relevant features and providing
references for the reader who needs additional information.
• Chapter 2, “G2_LE Core,” provides an overview of the MPC8280 core.
• Chapter 3, “Memory Map,” presents a table showing where MPC8280 registers are mapped in
memory. It includes cross references that indicate where the registers are described in detail.
Conventions
Part I uses the following notational conventions:
mnemonics
Instruction mnemonics are shown in lowercase bold.
italics
Italics indicate variable command parameters, for example, bcctrx.
Book titles in text are set in italics.
0x0
Prefix to denote hexadecimal number
0b0
Prefix to denote binary number
rA, rB
Instruction syntax used to identify a source GPR
rD
Instruction syntax used to identify a destination GPR
REG[FIELD]
Abbreviations or acronyms for registers or buffer descriptors are shown in
uppercase text. Specific bits, fields, or numerical ranges appear in brackets. For
example, MSR[LE] refers to the little-endian mode enable bit in the machine state
register.
x
In certain contexts, such as in a signal encoding or a bit field, indicates a don’t
care.
n
Indicates an undefined numerical value
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
I-1
Acronyms and Abbreviations
Table I-1 contains acronyms and abbreviations that are used in this document.
Table I-1. Acronyms and Abbreviated Terms
Term
Meaning
ATM
Asynchronous Mode
BD
Buffer descriptor
BPU
Branch processing unit
COP
Common on-chip processor
CP
Communications processor
CPM
Communications processor module
CRC
Cyclic redundancy check
CTR
Count register
DABR
Data address breakpoint register
DAR
Data address register
DEC
Decrementer register
DMA
Direct memory access
DPLL
Digital phase-locked loop
DRAM
Dynamic random access memory
DTLB
Data translation lookaside buffer
EA
Effective address
FCC‘
Fast communications controller
FPR
Floating-point register
GPCM
General-purpose chip-select machine
GPR
General-purpose register
HDLC
High-level data link control
I2C
Inter-integrated circuit
IEEE
Institute of Electrical and Electronics Engineers
ISDN
Integrated services digital network
ITLB
Instruction translation lookaside buffer
IU
Integer unit
JTAG
Joint Test Action Group
LRU
Least recently used (cache replacement algorithm)
LSU
Load/store unit
MCC
Multi-channel controller
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
I-2
Freescale Semiconductor
Table I-1. Acronyms and Abbreviated Terms (continued)
Term
Meaning
MII
Media-independent interface
MMU
Memory management unit
MSR
Machine state register
NMSI
Nonmultiplexed serial interface
OEA
Operating environment architecture
OSI
Open systems interconnection
PCI
Peripheral component interconnect
RISC
Reduced instruction set computing
RTC
Real-time clock
RTOS
Real-time operating system
Rx
Receive
SCC
Serial communications controller
SDLC
Synchronous data link control
SDMA
Serial DMA
SI
Serial interface
SIU
System interface unit
SMC
Serial management controller
SPI
Serial peripheral interface
SPR
Special-purpose register
SRAM
Static random access memory
TAP
Test access port
TB
Time base register
TDM
Time-division multiplexed
TLB
Translation lookaside buffer
TSA
Time-slot assigner
Tx
Transmit
UART
Universal asynchronous receiver/transmitter
UISA
User instruction set architecture
UPM
User-programmable machine
VEA
Virtual environment architecture
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
I-3
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
I-4
Freescale Semiconductor
Chapter 1
Overview
The MPC8280 is a versatile communications processor that integrates on one chip a high-performance
PowerPC™ RISC microprocessor, a very flexible system integration unit, and many communications
peripheral controllers that can be used in a variety of applications, particularly in communications and
networking systems.
The MPC8280 core—a G2_LE—is an embedded variant of the MPC603e microprocessor with 16 Kbytes
of instruction cache and 16 Kbytes of data cache. The system interface unit (SIU) consists of a flexible
memory controller that interfaces to almost any user-defined memory system, a 60x-to-PCI bus bridge,
and many other peripherals making this device a complete system on a chip.
The MPC8280 communications processor module (CPM) includes all the peripherals found in the
MPC8260 PowerQUICC II family. In addition, the MPC8280 offers USB functionality.
This manual describes the functional operation of MPC8280, with an emphasis on peripheral functions.
Chapter 2, “G2_LE Core,” is an overview of the microprocessor core; detailed information about the core
can be found in the G2 Core Reference Manual (order number: G2CORERM).
1.1
Features
The following is an overview of the MPC8280 feature set:
• Dual-issue integer (G2_LE) core
— A core version of the MPC603e microprocessor
— System core microprocessor supporting frequencies of 166–450 MHz
— Separate 16-Kbyte data and instruction caches:
– Four-way set associative
– Physically addressed
– LRU replacement algorithm
— PowerPC architecture-compliant memory management unit (MMU)
— Common on-chip processor (COP) test interface
— Supports bus snooping for data cache coherency
— Floating-point unit (FPU)
• Separate power supply for internal logic and for I/O
• Separate PLLs for G2_LE core and for the CPM
— G2_LE core and CPM can run at different frequencies for power/performance optimization
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
1-1
Overview
•
•
•
•
— Internal core/bus clock multiplier that provides 2:1, 2.5:1, 3:1, 3.5:1, 4:1, 4.5:1, 5:1, 6:1, 7:1,
8:1 ratios
— Internal CPM/bus clock multiplier that provides 2:1, 2.5:1, 3:1, 3.5:1, 4:1, 5:1, 6:1, 8:1 ratios
64-bit data and 32-bit address 60x bus
— Bus supports multiple master designs
— Supports single- and four-beat burst transfers
— 64-, 32-, 16-, and 8-bit port sizes controlled by on-chip memory controller
— Supports data parity or ECC and address parity
32-bit data and 18-bit address local bus
— Single-master bus, supports external slaves
— Eight-beat burst transfers
— 32-, 16-, and 8-bit port sizes controlled by on-chip memory controller
60x-to-PCI bridge
— Programmable host bridge and agent
— 32-bit data bus, 66.67/83.3/100 MHz, 3.3 V
— Synchronous and asynchronous 60x and PCI clock modes
— All internal address space available to external PCI host
— DMA for memory block transfers
— PCI-to-60x address remapping
PCI bridge
— PCI Specification Revision 2.2 compliant and supports frequencies up to 66 MHz
— On-chip arbitration
— Support for PCI-to-60x-memory and 60x-memory-to-PCI streaming
— PCI host bridge or peripheral capabilities
— Includes 4 DMA channels for the following transfers:
– PCI-to-60x to 60x-to-PCI
– 60x-to-PCI to PCI-to-60x
– PCI-to-60x to PCI-to-60x
– 60x-to-PCI to 60x-to-PCI
— Includes all of the configuration registers (which are automatically loaded from the EPROM
and used to configure the MPC8280) required by the PCI standard as well as message and
doorbell registers
— Supports the I2O standard
— Hot-swap friendly (supports the hot swap specification as defined by PICMG 2.1 R1.0 August
3, 1998)
— Support for 66.67/83.33/100 MHz, 3.3 V specification
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
1-2
Freescale Semiconductor
Overview
•
•
•
•
— 60x-PCI bus core logic that uses a buffer pool to allocate buffers for each port
— Uses the local bus signals, removing need for additional pins
System interface unit (SIU)
— Clock synthesizer
— Reset controller
— Real-time clock (RTC) register
— Periodic interrupt timer
— Hardware bus monitor and software watchdog timer
— IEEE 1149.1 JTAG test access port
12-bank memory controller
— Glueless interface to SRAM, page mode SDRAM, DRAM, EPROM, Flash and other userdefinable peripherals
— Byte write enables and selectable parity generation
— 32-bit address decodes with programmable bank size
— Three user-programmable machines, general-purpose chip-select machine, and page-mode
pipeline SDRAM machine
— Byte selects for 64-bit bus width (60x) and for 32-bit bus width (local)
— Dedicated interface logic for SDRAM
CPU core can be disabled and the device can be used in slave mode to an external core
Communications processor module (CPM)
— Embedded 32-bit communications processor (CP) uses a RISC architecture for flexible support
for communications protocols
— Interfaces to G2_LE core through an on-chip 32-Kbyte dual-port data RAM, an on-chip
32-Kbyte dual-port instruction RAM and DMA controller
— Serial DMA channels for receive and transmit on all serial channels
— Parallel I/O registers with open-drain and interrupt capability
— Virtual DMA functionality executing memory-to-memory and memory-to-I/O transfers
— Three fast communications controllers supporting the following protocols:
– 10/100-Mbit Ethernet/IEEE 802.3 CDMA/CS interface through media independent
interface (MII) or reduced media independent interface (RMII)
– ATM—Full-duplex SAR protocols at 155 Mbps, through UTOPIA interface, AAL5, AAL1,
AAL0 protocols, TM 4.0 CBR, VBR, UBR, ABR traffic types, up to 64 K external
connections (no ATM support for the MPC8270)
– Transparent
– HDLC—Up to T3 rates (clear channel)
– FCC2 can also be connected to the TC layer (MPC8280 only)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
1-3
Overview
— Two multichannel controllers (MCCs) (one MCC on the MPC8270)
– Each MCC handles 128 serial, full-duplex, 64-Kbps data channels. Each MCC can be split
into four subgroups of 32 channels each.
– Almost any combination of subgroups can be multiplexed to single or multiple TDM
interfaces up to four TDM interfaces per MCC
— Four serial communications controllers (SCCs) identical to those on the MPC860, supporting
the digital portions of the following protocols:
– Ethernet/IEEE 802.3 CDMA/CS
– HDLC/SDLC and HDLC bus
– Universal asynchronous receiver transmitter (UART)
– Synchronous UART
– Binary synchronous (BISYNC) communications
– Transparent
— Universal serial bus (USB) controller
– USB 2.0 full/low rate compatible
– USB host mode
–Supports control, bulk, interrupt, and isochronous data transfers
–CRC16 generation and checking
–NRZI encoding/decoding with bit stuffing
–Supports both 12- and 1.5-Mbps data rates (automatic generation of preamble token and
data rate configuration). Note that low-speed operation requires an external hub.
–Flexible data buffers with multiple buffers per frame
–Supports local loopback mode for diagnostics (12 Mbps only)
– Supports USB slave mode
–Four independent endpoints support control, bulk, interrupt, and isochronous data
transfers
–CRC16 generation and checking
–CRC5 checking
–NRZI encoding/decoding with bit stuffing
–12- or 1.5-Mbps data rate
–Flexible data buffers with multiple buffers per frame
–Automatic retransmission upon transmit error
— Two serial management controllers (SMCs), identical to those of the MPC860
– Provide management for BRI devices as general circuit interface (GCI) controllers in timedivision-multiplexed (TDM) channels
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
1-4
Freescale Semiconductor
Overview
—
—
—
—
—
—
—
1.2
– Transparent
– UART (low-speed operation)
One serial peripheral interface identical to the MPC860 SPI
One inter-integrated circuit (I2C) controller (identical to the MPC860 I2C controller)
– Microwire compatible
– Multiple-master, single-master, and slave modes
Up to eight TDM interfaces (four on the MPC8270)
– Supports two groups of four TDM channels for a total of eight TDMs (one group of four on
the MPC8270 and the MPC8275)
– 2,048 bytes of SI RAM
– Bit or byte resolution
– Independent transmit and receive routing, frame synchronization
– Supports T1, CEPT, T1/E1, T3/E3, pulse code modulation highway, ISDN basic rate, ISDN
primary rate, Freescale interchip digital link (IDL), general circuit interface (GCI), and
user-defined TDM serial interfaces
Eight independent baud rate generators and 20 input clock pins for supplying clocks to FCCs,
SCCs, SMCs, and serial channels
Four independent 16-bit timers that can be interconnected as two 32-bit timers
Transmission convergence (TC) layer (MPC8280 only)
Inverse multiplexing for ATM capabilities (IMA) (MPC8280 only). Supported by eight TC
layers between the TDMs and FCC2.
Architecture Overview
The MPC8280 has two external buses to accommodate bandwidth requirements from the high-speed
system core and the very fast communications channels. Figure 1-1 shows the block diagram of the
superset MPC8280 device. Features that are device- or package-specific are noted. For package
information, refer to the MPC8280 PowerQUICC II Family Hardware Specifications (order number:
MPC8280EC).
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
1-5
Overview
16 Kbytes
I-Cache
I-MMU
System Interface Unit
(SIU)
G2_LE Core
16 Kbytes
D-Cache
Bus Interface Unit
Communication Processor Module (CPM)
Timers
32 KB
Instruction
RAM
Interrupt
Controller
Parallel I/O
MCC11
MCC2
Serial
DMAs
FCC2
FCC3
TC Layer Hardware1
SCC1
SCC2
32 bits, up to 100 MHz
Clock Counter
4 Virtual
IDMAs
IMA 1
Microcode
FCC1
or
Local Bus
Memory Controller
32 KB
Data
RAM
32-bit RISC Microcontroller
and Program ROM
Baud Rate
Generators
PCI Bus
32 bits, up to 66 MHz
60x-to-PCI
Bridge
60x-to-Local
Bridge
D-MMU
60x Bus
SCC3
SCC4/
USB
System Functions
SMC1
SMC2
SPI
I2C
Time Slot Assigner
Serial Interface2
8 TDM Ports2
3 MII or RMII
Ports
2 UTOPIA
Ports3
Non-Multiplexed
I/O
Notes:
1 MPC8280 only (not on MPC8270, the VR package, nor the ZQ package)
2 MPC8280 has 2 serial interface (SI) blocks and 8 TDM ports. MPC8270 and the VR and ZQ packages have
only 1 SI block and 4 TDM ports (TDM2[A–D]).
3 MPC8280, MPC8275VR, MPC8275ZQ only (not on MPC8270, MPC8270VR, nor MPC8270ZQ)
Figure 1-1. MPC8280 Block Diagram
Both the system core and the CPM have an internal PLL, which allows independent optimization of the
frequencies at which they run. The system core and CPM are both connected to the 60x bus.
1.2.1
G2_LE Core
The G2_LE core is derived from the MPC603e microprocessor with power management modifications.
The core is a high-performance low-power implementation of the family of reduced instruction set
computer (RISC) microprocessors. The G2_LE core implements the 32-bit portion of the PowerPC
architecture, which provides 32-bit effective addresses, integer data types of 8, 16, and 32 bits. The G2_LE
cache provides snooping to ensure data coherency with other masters. This helps ensure coherency
between the CPM and system core.
The core includes 16 Kbytes of instruction cache and 16 Kbytes of data cache. It has a 64-bit
split-transaction external data bus, which is connected directly to the external MPC8280 pins.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
1-6
Freescale Semiconductor
Overview
The G2_LE core has an internal common on-chip (COP) debug processor. This processor allows access to
internal scan chains for debugging purposes. It is also used as a serial connection to the core for emulator
support.
The G2_LE core can be disabled. In this mode, the MPC8280 functions as a slave peripheral to an external
core or to another PowerQUICC II device with its core enabled.
1.2.2
System Interface Unit (SIU)
The SIU consists of the following:
• A 60x-compatible parallel system bus configurable to 64-bit data width. The MPC8280 supports
64-, 32-, 16-, and 8-bit port sizes. The MPC8280 internal arbiter arbitrates between internal
components that can access the bus (system core, PCI bridge, CPM, and one external master). This
arbiter can be disabled, and an external arbiter can be used if necessary.
• A local (32-bit data, 32-bit internal and 18-bit external address) bus. This bus is used to enhance
the operation of the very high-speed communication controllers. Without requiring extensive
manipulation by the core, the bus can be used to store connection tables for ATM or buffer
descriptors (BDs) for the communication channels or raw data that is transmitted between
channels. The local bus is synchronous to the 60x bus and runs at the same frequency.
• The local bus can be configured as a 32-bit data and up to 66 MHz PCI (version 2.1) bus. In PCI
mode the bus can be programmed as a host or as an agent. The PCI bus can be configured to run
synchronously or asynchronously to the 60x bus. The MPC8280 has an internal PCI bridge with
an efficient 60x-to-PCI DMA for memory block transfers.
• Applications that require both the local bus and PCI bus need to connect an external PCI bridge.
• Memory controller supporting 12 memory banks that can be allocated for either the system or the
local bus. The memory controller is an enhanced version of the MPC860 memory controller. It
supports three user-programmable machines. Besides all MPC860 features, the memory controller
also supports SDRAM with page mode and address data pipeline.
• Supports JTAG controller IEEE 1149.1 test access port (TAP).
• A bus monitor that prevents 60x bus lock-ups, a real-time clock, a periodic interrupt timer, and
other system functions useful in embedded applications.
• Glueless interface to L2 cache (MPC2605) and 4-/16-K-entry CAM
(MCM69C232/MCM69C432).
1.2.3
Communications Processor Module (CPM)
The CPM contains features that allow the MPC8280 to excel in a variety of applications targeted mainly
for networking and telecommunication markets.
The CPM is a superset of the MPC860 PowerQUICC CPM, with enhancements on the CP performance
and additional hardware and microcode routines that support high bit rate protocols like ATM (up to 155
Mbps full-duplex) and Fast Ethernet (100-Mbps full-duplex).
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
1-7
Overview
The following list summarizes the major features of the CPM:
• The CP is an embedded 32-bit RISC controller residing on a separate bus (CPM local bus) from
the 60x bus (used by the system core). With this separate bus, the CP does not affect the
performance of the G2_LE core. The CP handles the lower layer tasks and DMA control activities,
leaving the G2_LE core free to handle higher layer activities. The CP has an instruction set
optimized for communications, but can also be used for general-purpose applications, relieving the
system core of small often repeated tasks.
• Two serial DMA (SDMA) that can do simultaneous transfers, optimized for burst transfers to the
60x bus and to the local bus.
• Three full-duplex, serial fast communications controllers (FCCs) supporting ATM (155 Mbps)
protocol through UTOPIA2 interface (there are two UTOPIA interfaces on the MPC8280), IEEE
802.3 and Fast Ethernet protocols, HDLC up to E3 rates (45 Mbps) and totally transparent
operation. Each FCC can be configured to transmit fully transparent and receive HDLC or
vice-versa. (Note that the MPC8270 does not support ATM (155 Mbps) protocol.)
• Two multichannel controllers (MCCs) that can handle an aggregate of 256 X 64 Kbps HDLC or
transparent channels, multiplexed on up to eight TDM interfaces. The MCC also supports
super-channels of rates higher than 64 Kbps and subchanneling of the 64-Kbps channels.
• Four full-duplex serial communications controllers (SCCs) supporting IEEE802.3/Ethernet, highlevel synchronous data link control, HDLC, local talk, UART, synchronous UART, BISYNC, and
transparent.
• Two full-duplex serial management controllers (SMC) supporting GCI, UART, and transparent
operations
• Serial peripheral interface (SPI) and I2C bus controllers
• Time-slot assigner (TSA) that supports multiplexing of data from any of the four SCCs, three
FCCs, and two SMCs.
1.3
Software Compatibility Issues
As much as possible, the MPC8280 CPM features were made similar to those of the previous MPC860
PowerQUICC family devices and the MPC8260 PowerQUICC II family devices. The code flow ports
easily from previous devices to the MPC8280, except for new protocols supported by the MPC8280.
Although many registers are new, most registers retain the old status and event bits, so an understanding
of the programming models of the MC68360, MPC860, or MPC85015 is helpful. Note that the MPC8280
initialization code requires changes from the MPC860 initialization code (Freescale provides reference
code).
1.3.1
Signals
Figure 1-2 shows MPC8280 signals grouped by function. Note that many of these signals are multiplexed
and this figure does not indicate how these signals are multiplexed.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
1-8
Freescale Semiconductor
Overview
NOTE
A bar over a signal name indicates that the signal is active low—for
example, BB (bus busy). Active-low signals are referred to as asserted
(active) when they are low and negated when they are high. Signals that are
not active low, such as TSIZ[0–3] (transfer size signals) are referred to as
asserted when they are high and negated when they are low.
VCCSYN/GNDSYN/VCCSYN1//VDDH/ ⎯⎯⎯> 100
VDD/VSS
PCI_PAR/L_A14 <⎯⎯> 1
SMI/PCI_FRAME/L_A15 <⎯⎯> 1
PCI_TRDY/L_A16 <⎯⎯> 1
CKSTOP_OUT/PCI_IRDY/L_A17 <⎯⎯> 1
PCI_STOP/L_A18 <⎯⎯> 1
PCI_DEVSEL/L_A19 <⎯⎯> 1
PCI_IDSEL/L_A20 <⎯⎯> 1
PCI_PERR/L_A21 <⎯⎯> 1
PCI_SERR/L_A22 <⎯⎯> 1
PCI_REQ0/L_A23 <⎯⎯> 1
CPCI_HS_ES/PCI_REQ1/L_A24 <⎯⎯> 1
PCI_GNT0/L_A25 <⎯⎯> 1
CPCI_HS_LED/PCI_GNT1/L_A26 <⎯⎯⎯ 1
CPCI_HS_ENUM/PCI_CLK/L_A27 <⎯⎯> 1
CORE_SRESET/PCI_RST/L_A28 <⎯⎯> 1
PCI_INTA/L_A29 <⎯⎯> 1
PCI_REQ2/L_A30 <⎯⎯> 1
DLLOUT/L_A31 <⎯⎯> 1
PCI_AD[0–31]/LCL_D[0–31] <⎯⎯> 32
PCI_C/BE[0–3]/LCL_DP[0–3] <⎯⎯> 4
PCI_CFG[3–0]/LBS[0–3]/
<⎯⎯⎯
LSDDQM[0–3]/LWE[0–3]
4
PCI_MODCK_H0/LGPL0/LSDA10
PCI_MODCK_H1/LGPL1/LSDWE
PCI_MODCK_H2/LGPL2/LSDRAS/LOE
PCI_MODCK_H3/LGPL3/LSDCAS
LPBS/LGPL4/LUPMWAIT/LGTA
PCI_MODCK/LGPL5
LWR
<⎯⎯⎯
<⎯⎯⎯
<⎯⎯⎯
<⎯⎯⎯
<⎯⎯>
<⎯⎯>
<⎯⎯>
1
1
1
1
1
1
1
PA[0–31]
PB[4–31]
PC[0–31]
PD[4–31]
<⎯⎯>
<⎯⎯>
<⎯⎯>
<⎯⎯>
32
28
32
28
PCI_RST/PORESET⎯⎯⎯>
RSTCONF⎯⎯⎯>
HRESET<⎯⎯>
SRESET<⎯⎯>
QREQ<⎯⎯⎯
XFC⎯⎯⎯>
CLKIN1⎯⎯⎯>
TRIS⎯⎯⎯>
BNKSEL[0]/TC[0]/AP[1]/MODCK1<⎯⎯>
BNKSEL[1]/TC[1]/AP[2]/MODCK2<⎯⎯>
BNKSEL[2]/TC[2]/AP[3]/MODCK3<⎯⎯>
PCI_MODE ⎯⎯⎯>
CLKIN2 ⎯⎯⎯>
NC ⎯⎯⎯>
1
1
1
1
1
1
1
1
1
1
1
1
1
2
32 <⎯⎯>
L
O
C
A
L
B
U
S
6
0
x
B
U
S
M
E
M
C
P
I
O
R
S
T
C
L
K
M
E
M
C
J
T
A
G
5
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
64
1
1
1
1
1
1
1
1
1
1
1
1
1
10
1
1
2
1
1
8
1
1
1
1
1
1
1
1
1
1
1
A[0–31]
<⎯⎯> TT[0–4]
<⎯⎯> TSIZ[0–3]
<⎯⎯> TBST
<⎯⎯> GBL/IRQ1
<⎯⎯> CI/BADDR29/IRQ2
<⎯⎯> WT/BADDR30/IRQ3
<⎯⎯⎯ L2_HIT/IRQ4
<⎯⎯> CPU_BG/BADDR31/IRQ5/CINT
⎯⎯⎯> CPU_DBG
⎯⎯⎯> CPU_BR
<⎯⎯> BR
<⎯⎯> BG
<⎯⎯> ABB/IRQ2
<⎯⎯> TS
<⎯⎯> AACK
<⎯⎯> ARTRY
<⎯⎯> DBG
<⎯⎯> DBB/IRQ3
<⎯⎯> D[0–63]
<⎯⎯> NC/DP0/RSRV/EXT_BR2
<⎯⎯> IRQ1/DP1/EXT_BG2
<⎯⎯> IRQ2/DP2/TLBISYNC/EXT_DBG2
<⎯⎯> IRQ3/DP3/CKSTP_OUT/EXT_BR3
<⎯⎯> IRQ4/DP4/CORE_SRESET/EXT_BG3
<⎯⎯> IRQ5/DP5/TBEN/EXT_DBG3/CINT
<⎯⎯> IRQ6/DP6/CSE0
<⎯⎯> IRQ7/DP7/CSE1
<⎯⎯> PSDVAL
<⎯⎯> TA
<⎯⎯> TEA
<⎯⎯> IRQ0/NMI_OUT
<⎯⎯> IRQ7/INT_OUT/APE
⎯⎯⎯> CS[0–9]
<⎯⎯> CS[10]/BCTL1
<⎯⎯> CS[11]/AP[0]
⎯⎯⎯> BADDR[27–28]
⎯⎯⎯> ALE
⎯⎯⎯> BCTL0
⎯⎯⎯> PWE[0–7]/PSDDQM[0–7]/PBS[0–7]
⎯⎯⎯> PSDA10/PGPL0
⎯⎯⎯> PSDWE/PGPL1
⎯⎯⎯> POE/PSDRAS/PGPL2
⎯⎯⎯> PSDCAS/PGPL3
<⎯⎯> PGTA/PUPMWAIT/PGPL4/PPBS
⎯⎯⎯> PSDAMUX/PGPL5
<⎯⎯⎯ TMS
<⎯⎯⎯ TDI
<⎯⎯⎯ TCK
<⎯⎯⎯ TRST
⎯⎯⎯> TDO
Figure 1-2. MPC8280 External Signals
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
1-9
Overview
1.4
Differences Between MPC860 and MPC8280
The following MPC860 features are not included in the MPC8280.
• On-chip crystal oscillators (must use external oscillator)
• 4-MHz oscillator (input clock must be at the bus speed)
• Low power (stand-by) modes
• Battery-backup real-time clock (must use external battery-backup clock)
• BDM (COP offers most of the same functionality)
• True little-endian mode
• PCMCIA interface
• Infrared (IR) port
• QMC protocol in SCC (256 HDLC channels are supported by the MCCs)
• Multiply and accumulate (MAC) block in the CPM
• Centronics port (PIP)
• Pulse-width modulated outputs
• SCC Ethernet controller option to sample 1 byte from the parallel port when a receive frame is
complete
• Parallel CAM interface for SCC (Ethernet)
1.5
Serial Protocol Table
Table 1-1 summarizes available protocols for each serial port.
Table 1-1. MPC8280 Serial Protocols
Port
Port
FCC
SCC
ATM (Utopia)1
√
100BaseT
√
10BaseT
√
√
HDLC
√
√
√
√
UART
√
DPLL
√
Multichannel
SMC
√
√
√
√
√
√
Universal serial bus
1
USB
√
HDLC_BUS
Transparent
MCC
Not on the MPC8270
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
1-10
Freescale Semiconductor
Overview
1.6
MPC8280 Configurations
The MPC8280 offers flexibility in configuring the device for specific applications. The functions
mentioned in the above sections are all available in the device, but not all of them can be used at the same
time. This does not imply that the device is not fully activated in any given implementation: The CPM
architecture has the advantage of using common hardware resources for many different protocols, and
applications. Two physical factors limit the functionality in any given system—pinout and performance.
1.6.1
Pin Configurations
Some pins have multiple functions. Choosing one function may preclude the use of another. Information
about multiplexing constraints can be found in Chapter 16, “CPM Multiplexing,” and Chapter 41,
“Parallel I/O Ports.”
1.6.2
Serial Performance
Serial performance depends on a number of factors:
• Serial rate versus CPM clock frequency for adequate sampling on serial channels
• Serial rate and protocol versus CPM clock frequency for CP protocol handling
• Serial rate and protocol versus bus bandwidth
• Serial rate and protocol versus system core clock for adequate protocol handling
The second item above is addressed in this section—the CP’s ability to handle high bit-rate protocols in
parallel. Slow bit-rate protocols do not significantly affect those numbers.
Table 1-2 describes a few options to configure the fast communications channels on the MPC8280. The
frequency specified is the minimum CPM frequency necessary to run the mentioned protocols
concurrently at full-duplex.
Table 1-2. Serial Performance1
CPM Clock
(MHz)
60x Bus Clock
(MHz)
100 BaseT
133
66
100 BaseT
133
66
128 * 64 Kbps channels
133
66
128 * 64 Kbps channels
133
66
155-Mbps ATM
256 * 64 Kbps channels
166
66
100 BaseT
256 * 64 Kbps channels
133
66
45-Mbps HDLC
256 * 64 Kbps
133
66
256 * 64 Kbps
166
66
16 * 576 Kbps
166
66
FCC1
FCC2
FCC3
155-Mbps ATM
100 BaseT
100 BaseT
100 BaseT
155-Mbps ATM
100 BaseT
45-Mbps HDLC
100 BaseT
100 BaseT
100 BaseT
1
MCC
For the MPC8270 see Table 1-3.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
1-11
Overview
Table 1-3 shows serial performance for the MPC8270, which does not support ATM (155-Mbps).
Table 1-3. MPC8270 Serial Performance
CPM Clock
(MHz)
60x Bus
Clock (MHz)
133
66
128 * 64 Kbps channels
133
66
45-Mbps
128 * 64 Kbps channels
133
66
45-Mbps HDLC
45-Mbps
128 * 64 Kbps channels
133
66
45-Mbps HDLC
45-Mbps
100 BaseT
128 * 64 Kbps channels
133
66
100 BaseT
45-Mbps
100 BaseT
8 * 576 Kbps channels
133
66
100 BaseT
100 BaseT
100 BaseT
128 * 64 Kbps channels
133
66
FCC 1
FCC 2
FCC 3
100 BaseT
100 BaseT
100 BaseT
100 BaseT
100 BaseT
100 BaseT
MCC
FCCs can also be used to run slower HDLC or 10 BaseT, for example. The CP’s RISC architecture has the
advantage of using common hardware resources for all FCCs.
1.7
Application Examples
The MPC8280 can be configured to meet many system application needs, as described in the following
sections and shown in Figure 1-3 through Figure 1-11.
NOTE: Differences among MPC8280 PowerQUICC II Family Devices
Refer to Figure 1-1 and Section 1.1, “Features,” to determine possible
differences in features between a given device and the following
descriptions.
1.7.1
Communication Systems
The following sections describe the following examples of communication systems:
• Section 1.7.1.1, “Remote Access Server”
• Section 1.7.1.2, “Regional Office Router”
• Section 1.7.1.3, “LAN-to-WAN Bridge Router”
• Section 1.7.1.4, “Cellular Base Station”
• Section 1.7.1.5, “Telecommunications Switch Controller”
• Section 1.7.1.6, “SONET Transmission Controller”
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
1-12
Freescale Semiconductor
Overview
1.7.1.1
Remote Access Server
Figure 1-3 shows remote access server configuration.
MPC8280
SDRAM/DRAM/SRAM
Quad
TDM0
60x Bus
T1
Framer
Channelized Data
(up to 256 channels)
TDM7
SDRAM/DRAM/SRAM
155 Mbps
ATM PHY
UTOPIA Multi PHY
Local Bus
or
MII
Transceiver
ATM
Connection Tables
(optional)
10/100BaseT
or
Framer
E3 clear channel
(takes one TDM)
DSP Bank
Slow
Comm
SMC/I2C/SPI/SCC
PHY
Slaves
on
Local
Bus
Figure 1-3. Remote Access Server Configuration
In this application, eight TDM ports are connected to external framers. In the MPC8280, each group of
four ports support up to 128 channels. One TDM interface can support 32–128 channels. The MPC8280
receives and transmits data in transparent or HDLC mode, and stores or retrieves the channelized data from
memory. The data can be stored either in memory residing on the 60x bus or in memory residing on the
local bus.
The main trunk can be configured as 155 Mbps full-duplex ATM, using the UTOPIA interface, or as
10/100 BaseT Fast Ethernet with MII interface, or as a high-speed serial channel (up to 45 Mbps). In ATM
mode, there may be a need to store connection tables in external memory on the local bus; for example,
128 active internal connections require 8 Kbytes of dual-port RAM. The need for local bus depends on the
total throughput of the system. The MPC8280 supports automatic (without software intervention) crossconnect between ATM and MCC, routing ATM AAL1 frames to MCC slots.
The local bus can be used as an interface to a bank of DSPs that can run code that performs analog modem
signal modulation. Data to and from the DSPs can be transferred through the parallel bus with the internal
virtual IDMA.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
1-13
Overview
The MPC8280 memory controller supports many types of memories, including EDO DRAM and
page-mode, pipeline SDRAM for efficient burst transfers.
1.7.1.2
Regional Office Router
Figure 1-4 shows a regional office router configuration.
MPC8280
Quad
TDM0
T1
Framer
TDM3
SDRAM/DRAM/SRAM
MII
10/100BaseT
Transceiver
60x Bus
Channelized Data
(up to 128 channels)
10/100BaseT
Slow
Comm
SMC/I2C/SPI/SCC
PHY
Figure 1-4. Regional Office Router Configuration
In this application, the MPC8280 is connected to four TDM interfaces channelizing up to 128 channels.
Each TDM port supports 32–128 channels. If 128 channels are needed, each TDM port can be configured
to support 32 channels. This example has two MII ports for 10/100 BaseT LAN connections. In all the
examples, the SCC ports can be used for management.
1.7.1.3
LAN-to-WAN Bridge Router
Figure 1-5 shows a LAN-to-WAN router configuration, which is similar to the previous example.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
1-14
Freescale Semiconductor
Overview
MPC8280
MII
Transceiver
10/100BaseT
SDRAM/DRAM/SRAM
60x Bus
155 Mbps
ATM
Data
UTOPIA Multi PHY
PHY
SDRAM/DRAM/SRAM
155 Mbps
ATM PHY
UTOPIA Multi PHY
Local Bus
or
MII
Transceiver
ATM Connection
Tables (optional)
10/100BaseT
Slow
Comm
SMC/I2C/SPI/SCC
PHY
Figure 1-5. LAN-to-WAN Bridge Router Configuration
1.7.1.4
Cellular Base Station
Figure 1-6 shows a cellular base station configuration.
MPC8280
SDRAM/DRAM/SRAM
TDM0
Framer
60x Bus
TDM1
Channelized Data
(up to 256 channels)
DSP Bank
Local Bus
Slow
Comm
SMC/I2C/SPI/SCC
PHY
Slaves
on
Local
Bus
Figure 1-6. Cellular Base Station Configuration
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
1-15
Overview
Here the MPC8280 channelizes two E1s (up to 256, 16-Kbps channels).
The local bus can control a bank of DSPs. Data to and from the DSPs can be transferred through the
parallel bus to the host port of the DSPs with the internal virtual IDMA.
The slow communication ports (SCCs, SMCs, I2C, SPI) can be used for management and debug functions.
1.7.1.5
Telecommunications Switch Controller
Figure 1-7 shows a telecommunications switch controller configuration.
MPC8280
155 Mbps
ATM
PHY
UTOPIA Multi PHY
SDRAM/DRAM/SRAM
60x Bus
10/100BaseT
MII
Transceiver
10/100BaseT
SDRAM/DRAM/SRAM
Local Bus
Slow
Comm
PHY
ATM
Connection
Tables
SMC/I2C/SPI/SCC
(10BaseT)
Figure 1-7. Telecommunications Switch Controller Configuration
The CPM supports a total aggregate throughput of 710 Mbps at 133 MHz. This includes two full-duplex
100 BaseT and one full-duplex 155 Mbps for ATM. The G2_LE core can operate at a different (higher)
speed, if the application requires it.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
1-16
Freescale Semiconductor
Overview
1.7.1.6
SONET Transmission Controller
Figure 1-8 shows a SONET transmission controller configuration.
MPC8280
TDM0
576 Kbps
SONET
Transceivers
TDM3
SDRAM/DRAM/SRAM
60x Bus
Channelized Data
(up to 16 channels)
MII
10/100BaseT
Transceiver
SDRAM/DRAM/SRAM
Local Bus
Slow
ATM
Connection
Tables
SMC/I2C/SPI/SCC
Comm
(10BaseT)
PHY
Figure 1-8. SONET Transmission Controller Configuration
In this application, the MPC8280 implements super channeling with the MCC. Nine 64-Kbps channels are
combined to form a 576-Kbps channel. The MPC8280 at 133 MHz can support up to sixteen 576-Kbps
superchannels. The MPC8280 also supports subchanneling (under 64 Kbps) with its MCC.
1.7.2
Bus Configurations
The following sections describe the following possible bus configurations:
• Section 1.7.2.1, “Basic System”
• Section 1.7.2.2, “High-Performance Communication”
• Section 1.7.2.3, “High-Performance System Microprocessor”
• Section 1.7.2.4, “PCI”
• Section 1.7.2.5, “PCI with 155-Mbps ATM”
• Section 1.7.2.6, “The MPC8280 as PCI Agent”
1.7.2.1
Basic System
In the basic system configuration, shown in Figure 1-9, the G2_LE core is enabled and uses the 64-bit 60x
data bus. The 32-bit local bus data is needed to store connection tables for many active ATM connections.
The local bus may also be used to store data that does not need to be heavily processed by the core. The
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
1-17
Overview
CP can store large data frames in the local memory without interfering with the operation of the system
core.
MPC8280
SDRAM/SRAM/DRAM/Flash
60x Bus
PHY
Communication
Channels
SDRAM/SRAM/DRAM
155 Mbps
ATM
PHY
UTOPIA
Local Bus
ATM
Connection Tables
Figure 1-9. Basic System Configuration
1.7.2.2
High-Performance Communication
Figure 1-10 shows a high-performance communication configuration.
MPC8280-A
SDRAM/SRAM/DRAM
Local Bus
Communication
Channels
PHY
ATM
Connection Tables
SDRAM/SRAM/DRAM/Flash
155 Mbps
ATM
PHY
UTOPIA
60x Bus
MPC8280-B
(master/slave)
Communication
Channels
PHY
SDRAM/SRAM/DRAM
155 Mbps
ATM
PHY
UTOPIA
Local Bus
or
PCI Bus
ATM
Connection Tables
Figure 1-10. High-Performance Communication
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
1-18
Freescale Semiconductor
Overview
Serial throughput is enhanced by connecting one MPC8280 in master or slave mode (with system core
enabled or disabled) to another MPC8280 in master mode with the core enabled. The core in MPC8280-A
can access the memory on the local bus of MPC8280-B.
1.7.2.3
High-Performance System Microprocessor
Figure 1-11 shows a configuration with a high-performance system microprocessor (MPC750).
MPC750
32-Kbyte I cache
32-Kbyte D cache
MPC8280 (slave)
Backside
Cache
SDRAM/SRAM/DRAM
60x Bus
Communication
Channels
PHY
SDRAM/SRAM/DRAM
155 Mbps
ATM
PHY
UTOPIA
Local Bus
ATM
Connection Tables
Figure 1-11. High-Performance System Microprocessor Configuration
In this system, the G2_LE core internal is disabled and an external high-performance microprocessor is
connected to the 60x bus.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
1-19
Overview
1.7.2.4
PCI
See Figure 1-12 for PCI configuration.
MPC8280
SDRAM/SRAM/DRAM/Flash
60x Bus
PHY
Communication
Channels
PCI Bus
Host or Agent
Figure 1-12. PCI Configuration
In this system the local bus is configured as PCI (33-MHz 32-bit data bus version 2.1). The MPC8280 can
be configured as a host or as an agent on the PCI bus. The 60x bus and PCI bus are asynchronous; there is
no frequency dependency between the two. The PCI bus is a 3.3-V bus.
1.7.2.5
PCI with 155-Mbps ATM
Figure 1-13 shows the PCI with 155-Mbps ATM configuration.
PCI Bus
PCI Bridge
SDRAM/SRAM/DRAM
MPC8280
60x Bus
PHY
Communication
Channels
SDRAM/SRAM/DRAM
ATM
PHY
UTOPIA
Local Bus
ATM
Connection Tables
Figure 1-13. PCI with 155-Mbps ATM Configuration
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
1-20
Freescale Semiconductor
Overview
This system supports PCI and implements a 155-Mbps, full-duplex ATM with more than 128 active
connections. The MPC8280 cannot support both functions simultaneously. The local bus is needed to store
ATM connection tables. Therefore, an external PCI bridge is necessary. In systems with fewer than 128
active connections or where the ATM average bit rate is lower that 155 Mbps, the local bus may not be
necessary to store connection tables, and it may be possible to use it as PCI bus.
1.7.2.6
The MPC8280 as PCI Agent
Figure 1-14 shows the configuration when the MPC8280 acts as the PCI agent.
SDRAM/SRAM/DRAM
MPC8280
60x Bus
PHY
ATM
PHY
Communication
Channels
UTOPIA
Agent
ATM Connection Tables
and/or
Communication Data
PCI Bus
Host
System Bus
PCI Bridge
Host
Processor
Memory
Figure 1-14. MPC8280 as PCI Agent
In this system, the MPC8280 is a PCI agent on an I/O card and the PCI host resides on the PCI bus. An
external PCI bridge is used to connect the host to the PCI bus. The internal PCI bridge in the MPC8280 is
used to bridge between the PCI bus and the 60x bus on the MPC8280.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
1-21
Overview
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
1-22
Freescale Semiconductor
Chapter 2
G2_LE Core
The MPC8280 contains an embedded G2_LE processor core, which is a derivative of the G2 core and the
original MPC603e PowerPC microprocessor design. This chapter provides an overview of the basic
functionality of the G2_LE processor core. For detailed information regarding the processor, refer to the
following:
• G2 PowerPC Core Reference Manual
• The Programming Environments for 32-Bit Implementations of the PowerPC Architecture
This section describes the details of the processor core, provides a block diagram showing the major
functional units, and briefly describes how those units interact.
MPC8280-specific implementation includes most of the G2_LE features. The unimplemented features are
described in the Section 2.2, “G2_LE Core Features.”
The signals associated with the processor core are described individually in Chapter 7, “60x Signals.”
Chapter 8, “The 60x Bus,” describes how those signals interact.
2.1
Overview
The processor core is a low-power implementation of the family reduced instruction set computing (RISC)
microprocessors that implement the PowerPC architecture. The processor core implements the 32-bit
portion of the PowerPC architecture, which supports 32-bit effective addresses, integer data types of 8, 16,
and 32 bits, and floating-point data types of 32 and 64 bits.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
2-1
G2_LE Core
Figure 2-1 is a block diagram of the processor core.
64-Bit (Two Instructions)
Branch
Processing
Unit
64-Bit
Sequential
Fetcher
64-Bit
CTR
CR
LR
Instruction
Queue
System
Register
Unit
64-Bit (Two Instructions)
Dispatch Unit
+
Instruction Unit
64-Bit
32-Bit
Integer
Unit
/ * +
GPR File
GP Rename
Registers
64-Bit
Load/Store
Unit
+
XER
FloatingPoint Unit
/ * +
FPR File
FP Rename
Registers
FPSCR
32-Bit
Completion
Unit
D MMU
SRs
DTLB
Power
Dissipation
Control
Time Base
Counter/
Decrementer
JTAG/COP
Interface
Clock
Multiplier
Tags
DBAT
Array
I MMU
SRs
64-Bit
IBAT
Array
ITLB
16-Kbyte
D Cache
16-Kbyte
I Cache
Tags
Touch Load Buffer
Core Interface
Copy-Back Buffer
32-Bit Address Bus
32-/64-Bit Data Bus
Figure 2-1. MPC8280 Integrated Processor Core Block Diagram
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
2-2
Freescale Semiconductor
G2_LE Core
The processor core is a superscalar processor that can issue and retire as many as three instructions per
clock. Instructions can execute out of order for increased performance; however, the processor core makes
completion appear sequential.
The processor core integrates five execution units—an integer unit (IU), a floating-point unit (FPU), a
branch processing unit (BPU), a load/store unit (LSU), and a system register unit (SRU). The ability to
execute five instructions in parallel and the use of simple instructions with rapid execution times yield high
efficiency and throughput. Most integer instructions execute in one clock cycle. On the processor core, the
FPU is pipelined so a single-precision multiply-add instruction can be issued and completed every clock
cycle. The processor core provides hardware support for all single- and double-precision floating-point
operations for most value representations and all rounding modes.
The processor core supports integer data types of 8, 16, and 32 bits, and floating-point data types of 32 and
64 bits. The 32 architecturally-defined floating point registers (FPRs) can be used to hold 32, 64-bit
operands that can in turn be transferred to and from the 32 general-purpose registers (GPRs), which can
hold 32, 32-bit operands.
The processor core provides separate on-chip, 16-Kbyte, four-way set-associative, physically addressed
caches for instructions and data and on-chip instruction and data memory management units (MMUs). The
MMUs contain 64-entry, two-way set-associative, data and instruction translation lookaside buffers
(DTLB and ITLB) that provide support for demand-paged virtual memory address translation and
variable-sized block translation. The TLBs and caches use a least recently used (LRU) replacement
algorithm. The processor core also supports block address translation through the use of two independent
instruction and data block address translation (IBAT and DBAT) arrays of eight entries each. Effective
addresses are compared simultaneously with all eight entries in the BAT array during block translation. In
accordance with the PowerPC architecture, if an effective address hits in both the TLB and BAT array, the
BAT translation takes priority.
As an added feature to the MPC603e core, the MPC8280 can lock the contents of 1–3 ways in the
instruction and data cache (or an entire cache). For example, this allows embedded applications to lock
interrupt routines or other important (time-sensitive) instruction sequences into the instruction cache. It
allows data to be locked into the data cache, which may be important to code that must have deterministic
execution.
The processor core has a 60x bus that incorporates a 64-bit data bus and a 32-bit address bus. The processor
core supports single-beat and burst data transfers for memory accesses and supports memory-mapped I/O
operations.
2.2
G2_LE Core Features
This section describes the major features of the processor core:
• High-performance, superscalar microprocessor
— As many as three instructions issued and retired per clock cycle
— As many as four instructions in execution per clock cycle
— Single-cycle execution for most instructions
— Pipelined FPU for all single-precision and most double-precision operations
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
2-3
G2_LE Core
•
•
•
•
Five independent execution units and two register files
— BPU featuring static branch prediction
— A 32-bit IU
— Fully IEEE 754–compliant FPU for both single- and double-precision operations
— LSU for data transfer between data cache and GPRs and FPRs
— SRU that executes condition register (CR), special-purpose register (SPR), and integer
add/compare instructions
— Thirty-two GPRs for integer operands
— Thirty-two FPRs for floating-point operands. They also can be used for general operands using
floating-point load and store operations.
High instruction and data throughput
— Zero-cycle branch capability (branch folding)
— Programmable static branch prediction on unresolved conditional branches
— BPU that performs CR lookahead operations
— Instruction fetch unit capable of fetching two instructions per clock from the instruction cache
— A six-entry instruction queue that provides lookahead capability
— Independent pipelines with feed-forwarding that reduces data dependencies in hardware
— 16-Kbyte data cache—Four-way set-associative, physically addressed; LRU replacement
algorithm
— 16-Kbyte instruction cache—Four-way set-associative, physically addressed; LRU
replacement algorithm
— Cache write-back or write-through operation programmable on a per page or per block basis
— Address translation facilities for 4-Kbyte page size, variable block size, and 256-Mbyte
segment size
— A 64-entry, two-way set-associative ITLB
— A 64-entry, two-way set-associative DTLB
— Eight-entry data and instruction BAT arrays providing 128-Kbyte to 256-Mbyte blocks
— Software table search operations and updates supported through fast trap mechanism
— 52-bit virtual address; 32-bit physical address
Facilities for enhanced system performance
— A 32- or 64-bit, split-transaction external data bus with burst transfers
— Support for one-level address pipelining and out-of-order bus transactions
— Critical interrupt exception support
— Hardware support for misaligned little-endian accesses
Integrated power management
— One power-saving mode: doze
— Automatic dynamic power reduction when internal functional units are idle
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
2-4
Freescale Semiconductor
G2_LE Core
•
Deterministic behavior and debug features
— On-chip cache locking options for the instruction and data caches (1–3 ways or the entire cache
contents can be locked)
— In-system testability and debugging features through JTAG and boundary-scan capability
Features supported by the G2_LE core not present on the MPC8280:
• True little-endian mode for compatibility with other true little-endian devices
• Nap and sleep power-saving modes
Figure 2-1 shows how the execution units—IU, BPU, LSU, and SRU—operate independently and in
parallel. Note that this is a conceptual diagram and does not attempt to show how these features are
physically implemented on the chip.
The processor core provides address translation and protection facilities, including an ITLB, DTLB, and
instruction and data BAT arrays. Instruction fetching and issuing is handled in the instruction unit. The
MMUs translate addresses for cache or external memory accesses.
2.2.1
Instruction Unit
As shown in Figure 2-1, the instruction unit, which contains a fetch unit, instruction queue, dispatch unit,
and the BPU, provides centralized control of instruction flow to the execution units. The instruction unit
determines the address of the next instruction to be fetched based on information from the sequential
fetcher and from the BPU.
The instruction unit fetches the instructions from the instruction cache into the instruction queue. The BPU
extracts branch instructions from the fetcher and uses static branch prediction on unresolved conditional
branches to allow the instruction unit to fetch instructions from a predicted target instruction stream while
a conditional branch is evaluated. The BPU folds out branch instructions for unconditional branches or
conditional branches unaffected by instructions in progress in the execution pipeline.
Instructions issued beyond a predicted branch do not complete execution until the branch is resolved,
preserving the programming model of sequential execution. If any of these instructions are to be executed
in the BPU, they are decoded but not issued. Instructions to be executed by the IU, LSU, and SRU are
issued and allowed to complete up to the register write-back stage. Write-back is allowed when a correctly
predicted branch is resolved, and instruction execution continues without interruption on the predicted
path. If branch prediction is incorrect, the instruction unit flushes all predicted path instructions, and
instructions are issued from the correct path.
2.2.2
Instruction Queue and Dispatch Unit
The instruction queue (IQ), shown in Figure 2-1, holds as many as six instructions and loads up to two
instructions from the instruction unit during a single cycle. The instruction fetch unit continuously loads
as many instructions as space in the IQ allows. Instructions are dispatched to their respective execution
units from the dispatch unit at a maximum rate of two instructions per cycle. Reservation stations at the
IU, LSU, and SRU facilitate instruction dispatch to those units. The dispatch unit checks for source and
destination register dependencies, determines dispatch serializations, and inhibits subsequent instruction
dispatching as required. Section 2.7, “Instruction Timing,” describes instruction dispatch in detail.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
2-5
G2_LE Core
2.2.3
Branch Processing Unit (BPU)
The BPU receives branch instructions from the fetch unit and performs CR lookahead operations on
conditional branches to resolve them early, achieving the effect of a zero-cycle branch in many cases.
The BPU uses a bit in the instruction encoding to predict the direction of the conditional branch. Therefore,
when an unresolved conditional branch instruction is encountered, instructions are fetched from the
predicted target stream until the conditional branch is resolved.
The BPU contains an adder to compute branch target addresses and three user-control registers—the link
register (LR), the count register (CTR), and the CR. The BPU calculates the return pointer for subroutine
calls and saves it into the LR for certain types of branch instructions. The LR also contains the branch
target address for the Branch Conditional to Link Register (bclrx) instruction. The CTR contains the
branch target address for the Branch Conditional to Count Register (bcctrx) instruction. The contents of
the LR and CTR can be copied to or from any GPR. Because the BPU uses dedicated registers rather than
GPRs or FPRs, execution of branch instructions is largely independent from execution of other
instructions.
2.2.4
Independent Execution Units
The PowerPC architecture’s support for independent execution units allows implementation of processors
with out-of-order instruction execution. For example, because branch instructions do not depend on GPRs
or FPRs, branches can often be resolved early, eliminating stalls caused by taken branches.
In addition to the BPU, the processor core provides three other execution units and a completion unit,
which are described in the following sections.
2.2.4.1
Integer Unit (IU)
The IU executes all integer instructions. The IU executes one integer instruction at a time, performing
computations with its arithmetic logic unit (ALU), multiplier, divider, and XER register. Most integer
instructions are single-cycle instructions. Thirty-two general-purpose registers are provided to support
integer operations. Stalls due to contention for GPRs are minimized by the automatic allocation of rename
registers. The processor core writes the contents of the rename registers to the appropriate GPR when
integer instructions are retired by the completion unit.
2.2.4.2
Floating-Point Unit (FPU)
The FPU contains a single-precision multiply-add array and the floating-point status and control register
(FPSCR). The multiply-add array allows the processor core to efficiently implement multiply and
multiply-add operations. The FPU is pipelined so that single-precision instructions and double-precision
instructions can be issued back-to-back. Thirty-two floating-point registers are provided to support
floating-point operations. Stalls due to contention for FPRs are minimized by the automatic allocation of
rename registers. The core writes the contents of the rename registers to the appropriate FPR when
floating-point instructions are retired by the completion unit.
The processor core supports all IEEE 754 floating-point data types (normalized, denormalized, NaN, zero,
and infinity) in hardware, eliminating the latency incurred by software exception routines.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
2-6
Freescale Semiconductor
G2_LE Core
2.2.4.3
Load/Store Unit (LSU)
The LSU executes all load and store instructions and provides the data transfer interface between the
GPRs, FPRs, and the cache/memory subsystem. The LSU calculates effective addresses, performs data
alignment, and provides sequencing for load/store string and multiple instructions.
Load and store instructions are issued and translated in program order; however, the actual memory
accesses can occur out of order. Synchronizing instructions are provided to enforce strict ordering where
needed.
Cacheable loads, when free of data dependencies, execute in an out-of-order manner with a maximum
throughput of one per cycle and a two-cycle total latency. Data returned from the cache is held in a rename
register until the completion logic commits the value to a GPR or FPR. Store operations do not occur until
a predicted branch is resolved. They remain in the store queue until the completion logic signals that the
store operation will be completed to memory.
The processor core executes store instructions with a maximum throughput of one per cycle and a
three-cycle total latency. The time required to perform the actual load or store operation varies depending
on whether the operation involves the cache, system memory, or an I/O device.
2.2.4.4
System Register Unit (SRU)
The SRU executes various system-level instructions, including condition register logical operations and
move to/from special-purpose register instructions, and also executes integer add/compare instructions.
Because SRU instructions affect modes of processor operation, most SRU instructions are
completion-serialized. That is, the instruction is held for execution in the SRU until all prior instructions
issued have completed. Results from completion-serialized instructions executed by the SRU are not
available or forwarded for subsequent instructions until the instruction completes.
2.2.5
Completion Unit
The completion unit tracks instructions from dispatch through execution, and then retires, or completes
them in program order. Completing an instruction commits the processor core to any architectural register
changes caused by that instruction. In-order completion ensures the correct architectural state when the
processor core must recover from a mispredicted branch or any exception.
Instruction state and other information required for completion is kept in a first-in-first-out (FIFO) queue
of five completion buffers. A single completion buffer is allocated for each instruction once it enters the
dispatch unit. An available completion buffer is a required resource for instruction dispatch; if no
completion buffers are available, instruction dispatch stalls. A maximum of two instructions per cycle are
completed in order from the queue.
2.2.6
Memory Subsystem Support
The processor core supports cache and memory management through separate instruction and data MMUs
(IMMU and DMMU). The processor core also provides dual 16-Kbyte instruction and data caches, and an
efficient processor bus interface to facilitate access to main memory and other bus subsystems. The
memory subsystem support functions are described in the following subsections.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
2-7
G2_LE Core
2.2.6.1
Memory Management Units (MMUs)
The processor core’s MMUs support up to 4 Petabytes (252) of virtual memory and 4 Gbytes (232) of
physical memory (referred to as real memory in the PowerPC architecture specification) for instructions
and data. The MMUs also control access privileges for these spaces on block and page granularities.
Referenced and changed status is maintained by the processor for each page to assist implementation of a
demand-paged virtual memory system. A key bit is implemented to provide information about memory
protection violations prior to page table search operations.
The LSU calculates effective addresses for data loads and stores, performs data alignment to and from
cache memory, and provides the sequencing for load and store string and multiple word instructions. The
instruction unit calculates the effective addresses for instruction fetching.
The MMUs translate effective addresses and enforce the protection hierarchy programmed by the
operating system in relation to the supervisor/user privilege level of the access and in relation to whether
the access is a load or store.
2.2.6.2
Cache Units
The processor core provides independent 16-Kbyte, four-way set-associative instruction and data caches.
The cache block size is 32 bytes. The caches are designed to adhere to a write-back policy, but the
processor core allows control of cacheability, write policy, and memory coherency at the page and block
levels. The caches use a least recently used (LRU) replacement algorithm.
The load/store and instruction fetch units provide the caches with the address of the data or instruction to
be fetched. In the case of a cache hit, the cache returns two words to the requesting unit.
2.3
Programming Model
The following subsections describe the PowerPC instruction set and addressing modes.
2.3.1
Register Set
This section describes the register organization in the processor core as defined by the three programming
environments of the PowerPC architecture—the user instruction set architecture (UISA), the virtual
environment architecture (VEA), and the operating environment architecture (OEA), as well as the G2_LE
core implementation-specific registers. Full descriptions of the basic register set defined by the PowerPC
architecture are provided in Chapter 2 in The Programming Environments Manual.
The PowerPC architecture defines register-to-register operations for all arithmetic instructions. Source
data for these instructions is accessed from the on-chip registers or is provided as an immediate value
embedded in the opcode. The three-register instruction format allows specification of a target register
distinct from the two source registers, thus preserving the original data for use by other instructions and
reducing the number of instructions required for certain operations. Data is transferred between memory
and registers with explicit load and store instructions only.
Figure 2-2 shows the complete MPC8280 register set and the programming environment to which each
register belongs. This figure includes both the PowerPC register set and the MPC8280-specific registers.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
2-8
Freescale Semiconductor
G2_LE Core
Note that some registers common to other processors that implement the PowerPC architecture may not
be implemented in the MPC8280’s processor core. Unsupported SPR values are treated as follows:
• Any mtspr with an invalid SPR executes as a no-op.
• Any mfspr with an invalid SPR causes boundedly undefined results in the target register.
Conversely, some SPRs in the processor core may not be implemented or may not be implemented in the
same way as in other processors that implement the PowerPC architecture.
2.3.1.1
PowerPC Register Set
The PowerPC UISA registers, shown in Figure 2-2, can be accessed by either user- or supervisor-level
instructions. The general-purpose registers (GPRs) and floating-point registers (FPRs) are accessed
through instruction operands. Access to registers can be explicit (that is, through the use of specific
instructions for that purpose such as the mtspr and mfspr instructions) or implicit as part of the execution
(or side effect) of an instruction. Some registers are accessed both explicitly and implicitly.
The number to the right of the register name indicates the number that is used in the syntax of the
instruction operands to access the register (for example, the number used to access the XER is 1). For more
information on the PowerPC register set, refer to Chapter 2 in The Programming Environments Manual.
Note that the reset value of the MSR exception prefix bit (MSR[IP]), described in the G2 Core Reference
Manual, is determined by the CIP bit in the hard reset configuration word in the MPC8280. This is
described in Section 5.4.1, “Hard Reset Configuration Word.”
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
2-9
G2_LE Core
SUPERVISOR MODEL
Configuration Registers
Hardware
Implementation
Registers
USER MODEL
General-Purpose
Registers (32-Bit)
GPR0
GPR1
Floating-Point
Registers (64-Bit)
FPR0
FPR1
SPR 1008
HID1 1
SPR 1009
HID2 1
SPR 1011
Condition Register
CR
FPSCR
Link Register
LR
SPR 8
Count Register
CTR
SPR 9
Time Base Facility
(For Reading)
TBL
SPR268
TBU
SPR269
Software Table
Search Registers 1
Data BAT Registers
DBAT0U
SPR 536
IBAT0L
SPR 529
DBAT0L
SPR 537
IBAT1U
SPR 530
DBAT1U
SPR 538
IBAT1L
SPR 531
DBAT1L
SPR 539
IBAT2U
SPR 532
DBAT2U
SPR 540
IBAT2L
SPR 533
DBAT2L
SPR 541
IBAT3U
SPR 534
DBAT3U
SPR 542
IBAT3L
SPR 535
DBAT3L
SPR 543
1
SPR 560
DBAT4U 1
SPR 568
IBAT4L 1
SPR 561
DBAT4L 1
SPR 569
IBAT5U 1
SPR 562
DBAT5U 1
SPR 570
IBAT5L 1
SPR 563
DBAT5L 1
SPR 571
SR0
IBAT6U 1
SPR 564
DBAT6U 1
SPR 572
SR1
SPR 565
DBAT6L
1
SPR 573
1
SPR 574
SPR 575
1
SPR 566
DBAT7U
IBAT7L 1
SPR 567
DBAT7L 1
IBAT7U
SPRG0
SPR 272
SPRG1
SPR 273
SPRG2
SPR 274
SPRG3
DSISR
SPR 26
SPRG4
SPR 276
SRR1
SPR 27
SPRG5
1
SPR 277
SPRG6 1
SPR 278
Critical Interrupt
Registers 1
CSRR0
SPR 58
CSRR1
SPR 59
SPR 977
SPR 978
HASH2
SPR 979
IMISS
SPR 980
ICMP
SPR 981
RPA
SPR 982
SPR 25
Segment Registers
SR15
Miscellaneous
Registers
DEC
EAR
SPR 282
Time Base Facility
(For Writing)
Data Address Register
DAR
SPR 22
External Address
Register (Optional)
Save and Restore
Registers
SRR0
SPR 279
DCMP
HASH1
SDR1
SPR 18
SPR 275
SPRG7
SPR 976
Decrementer
1
1
DMISS
SDR1
DSISR
SPR 19
TBL
SPR 284
TBU
SPR 285
Breakpoint Registers
Instruction/Data
Address Breakpoint
Register 1
IABR 1
Instruction/Data Address
Breakpoint Control 1
SPR 1010
IBCR
SPR 309
1
SPR 1018
DBCR
SPR 310
DABR 1
SPR 1013
DABR2 1
SPR 317
IABR2
1
SPR 287
Memory Management Registers
SPRGs
SPR 1
PVR
SPR 311
Exception Handling Registers
XER
XER
MBAR 2
SPR 286
SPR 528
IBAT6L 1
Floating-Point Status
and Control Register
Memory Base Address
Register
SVR 1
IBAT0U
IBAT4U
FPR31
System/Processor
Version Register
MSR
HID0 1
Instruction BAT
Registers
GPR31
Machine State
Register
These implementation-specific registers may not be supported by other PowerPC processors or processor cores.
Figure 2-2. MPC8280 Programming Model—Registers
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
2-10
Freescale Semiconductor
G2_LE Core
2.3.1.2
MPC8280-Specific Registers
The set of registers specific to the MPC603e are also shown in Figure 2-2. Most of these are described in
the G2 Core Reference Manual and are implemented in the MPC8280 as follows:
• MMU software table search registers: DMISS, DCMP, HASH1, HASH2, IMISS, ICMP, and RPA.
These registers facilitate the software required to search the page tables in memory.
• IABR and IABR2. These registers facilitate the setting of instruction address breakpoints.
• DABR and DABR2. These registers facilitate the setting of data address breakpoints.
• IBCR and DBCR. These registers give further control to the instruction and data address
breakpoints.
The hardware implementation-dependent registers (HIDx) are implemented differently in the MPC8280,
and they are described in the following subsections.
2.3.1.2.1
Hardware Implementation-Dependent Register 0 (HID0)
Figure 2-3 shows the MPC8280 implementation of HID0.
0
1
2
3
EMCP
—
EBA
EBD
16
17
18
19
ICE
DCE
4
6
7
—
20
21
8
PAR DOZE
22
ILOCK DLOCK ICFI DCFI
23
—
24
IFEM
9
10
11
—
STOP
DPM
25
26
27
—
12
14
—
28
FBIOB ABE
15
NHR
29
30
—
31
NOOPTI
Figure 2-3. Hardware Implementation Register 0 (HID0)
Table 2-1 shows the bit definitions for HID0.
Table 2-1. HID0 Field Descriptions
Bits
Name
Description
0
EMCP
Enable machine check input pin
0 The assertion of the MCP does not cause a machine check exception.
1 Enables the entry into a machine check exception based on assertion of the MCP input,
detection of a cache parity error, detection of an address parity error, or detection of a data
parity error.
Note that the machine check exception is further affected by MSR[ME], which specifies whether
the processor checkstops or continues processing.
1
—
2
EBA
Enable/disable 60x bus address parity checking
0 Prevents address parity checking.
1 Allows a address parity error to cause a checkstop if MSR[ME] = 0 or a machine check
exception if MSR[ME] = 1.
EBA and EBD let the processor operate with memory subsystems that do not generate parity.
3
EBD
Enable 60x bus data parity checking
0 Parity checking is disabled.
1 Allows a data parity error to cause a checkstop if MSR[ME] = 0 or a machine check exception
if MSR[ME] = 1.
EBA and EBD let the processor operate with memory subsystems that do not generate parity.
Reserved
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
2-11
G2_LE Core
Table 2-1. HID0 Field Descriptions (continued)
Bits
Name
Description
4–6
—
7
PAR
Disable precharge of ARTRY.
0 Precharge of ARTRY enabled
1 Alters bus protocol slightly by preventing the processor from driving ARTRY to high (negated)
state, allowing multiple ARTRY signals to be tied together. If this is done, the system must
restore the signals to the high state.
8
DOZE
Doze mode enable. Operates in conjunction with MSR[POW]. 1
0 Doze mode disabled.
1 Doze mode enabled. Doze mode is invoked by setting MSR[POW] after this bit is set. In doze
mode, the PLL, time base, and snooping remain active.
9
—
10
STOP
Stop mode enable. Operates in conjunction with MSR[POW]. 1
0 Stop mode disabled.
1 Stop mode enabled. Sleep mode is invoked by setting MSR[POW] while this bit is set. When
this occurs, the processor asserts QREQ to indicate that it is ready to enter sleep mode. The
main MPC8280’s PLL remains active and all the internal clocks—including the core’s
clock—stop.
11
DPM
Dynamic power management enable. 1
0 Dynamic power management is disabled.
1 Functional units enter a low-power mode automatically if the unit is idle. This does not affect
operational performance and is transparent to software or any external hardware.
12–14
—
15
NHR
Not hard reset (software-use only)—Helps software distinguish a hard reset from a soft reset.
0 A hard reset occurred if software had previously set this bit.
1 A hard reset has not occurred. If software sets this bit after a hard reset, when a reset occurs
and this bit remains set, software can tell it was a soft reset.
16
ICE
Instruction cache enable 2
0 The instruction cache is neither accessed nor updated. All pages are accessed as if they were
marked cache-inhibited (WIM = X1X). Potential cache accesses from the bus (snoop and
cache operations) are ignored. In the disabled state for the L1 caches, the cache tag state bits
are ignored and all accesses are propagated to the bus as single-beat transactions. For those
transactions, however, CI reflects the original state determined by address translation
regardless of cache disabled status. ICE is zero at power-up.
1 The instruction cache is enabled
17
DCE
Data cache enable 2
0 The data cache is neither accessed nor updated. All pages are accessed as if they were
marked cache-inhibited (WIM = X1X). Potential cache accesses from the bus (snoop and
cache operations) are ignored. In the disabled state for the L1 caches, the cache tag state bits
are ignored and all accesses are propagated to the bus as single-beat transactions. For those
transactions, however, CI reflects the original state determined by address translation
regardless of cache disabled status. DCE is zero at power-up.
1 The data cache is enabled.
Reserved
Reserved, should be cleared.
Reserved
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
2-12
Freescale Semiconductor
G2_LE Core
Table 2-1. HID0 Field Descriptions (continued)
Bits
Name
Description
18
ILOCK
Instruction cache lock
0 Normal operation
1 Instruction cache is locked. A locked cache supplies data normally on a hit, but an access is
treated as a cache-inhibited transaction on a miss. On a miss, the transaction to the bus is
single-beat, however, CI still reflects the original state as determined by address translation
independent of cache locked or disabled status.
To prevent locking during a cache access, an isync must precede the setting of ILOCK.
19
DLOCK
Data cache lock
0 Normal operation
1 Data cache is locked. A locked cache supplies data normally on a hit but an access is treated
as a cache-inhibited transaction on a miss. On a miss, the transaction to the bus is single-beat,
however, CI still reflects the original state as determined by address translation independent
of cache locked or disabled status. A snoop hit to a locked L1 data cache performs as if the
cache were not locked. A cache block invalidated by a snoop remains invalid until the cache is
unlocked.
To prevent locking during a cache access, a sync must precede the setting of DLOCK.
20
ICFI
Instruction cache flash invalidate 2
0 The instruction cache is not invalidated. The bit is cleared when the invalidation operation
begins (usually the next cycle after the write operation to the register). The instruction cache
must be enabled for the invalidation to occur.
1 An invalidate operation is issued that marks the state of each instruction cache block as invalid
without writing back modified cache blocks to memory. Cache access is blocked during this
time. Bus accesses to the cache are signaled as a miss during invalidate-all operations. Setting
ICFI clears all the valid bits of the blocks and the PLRU bits to point to way L0 of each set. Once
the L1 flash invalidate bits are set through an mtspr instruction, hardware automatically resets
these bits in the next cycle (provided that the corresponding cache enable bits are set in HID0).
21
DCFI
Data cache flash invalidate 2
0 The data cache is not invalidated. The bit is cleared when the invalidation operation begins
(usually the next cycle after the write operation to the register). The data cache must be
enabled for the invalidation to occur.
1 An invalidate operation is issued that marks the state of each data cache block as invalid
without writing back modified cache blocks to memory. Cache access is blocked during this
time. Bus accesses to the cache are signaled as a miss during invalidate-all operations. Setting
DCFI clears all the valid bits of the blocks and the PLRU bits to point to way L0 of each set.
Once the L1 flash invalidate bits are set through an mtspr instruction, hardware automatically
resets these bits in the next cycle (provided that the corresponding cache enable bits are set
in HID0).
22–23
—
24
IFEM
25–26
—
27
FBIOB
28
ABE
Reserved
Enable M bit on 60x bus for instruction fetches
0 M bit not reflected on 60x bus. Instruction fetches are treated as nonglobal on the bus.
1 Instruction fetches reflect the M bit from the WIM settings on the 60x bus.
Reserved
Force branch indirect on bus.
0 Register indirect branch targets are fetched normally
1 Forces register indirect branch targets to be fetched externally.
Address broadcast enable
0 dcbf, dcbi, and dcbst instructions are not broadcast on the 60x bus.
1 dcbf, dcbi, and dcbst generate address-only broadcast operations on the 60x bus.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
2-13
G2_LE Core
Table 2-1. HID0 Field Descriptions (continued)
Bits
Name
29–30
—
31
NOOPTI
1
Description
Reserved
No-op the data cache touch instructions.
0 The dcbt and dcbtst instructions are enabled.
1 The dcbt and dcbtst instructions are no-oped globally.
See Chapter 10, “Power Management,” of the G2 Core Reference Manual for more information.
See Chapter 4, “Instruction and Data Cache Operation,” of the G2 Core Reference Manual for more information.
2
2.3.1.2.2
Hardware Implementation-Dependent Register 1 (HID1)
The MPC8280 implementation of HID1 is shown in Figure 2-4.
0
4
5
31
PLLCFG
—
Figure 2-4. Hardware Implementation-Dependent Register 1 (HID1)
Table 2-2 shows the bit definitions for HID1.
Table 2-2. HID1 Field Descriptions
Bits
0–4
5–31
2.3.1.2.3
Name
Function
PLLCFG PLL configuration setting. These bits reflect the state of the PLL_CFG[0:4] signals.
—
Reserved
Hardware Implementation-Dependent Register 2 (HID2)
The processor core implements an additional hardware implementation-dependent register, shown in
Figure 2-5.
0
12
—
13
14
HBE —
15
SFP
16
18 19
IWLCK
23 24
—
26 27
DWLCK
31
—
Figure 2-5. Hardware Implementation-Dependent Register 2 (HID2)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
2-14
Freescale Semiconductor
G2_LE Core
Table 2-3 describes the HID2 fields.
Table 2-3. HID2 Field Descriptions
Bits
Name
0–12
—
13
HBE
14
—
15
SFP
16–18
19–23
24–26
27–31
2.3.1.2.4
Function
Reserved
High BAT enable. Enables the four additional pairs of BAT registers (IBAT4–IBAT7 and
DBAT4–DBAT7). These BATs are accessible by the mfspr and mtspr instructions regardless of the
setting of HID2[HBE].
Reserved
Speed for low power. Setting SFP reduces power consumption at the cost of reducing the maximum
frequency, which benefits power-sensitive applications that are not frequency-critical.
IWLCK Instruction cache way lock. Useful for locking blocks of instructions into the instruction cache for
time-critical applications that require deterministic behavior. See Section 2.4.2.3, “Cache Locking.”
—
Reserved
DWLCK Data cache way lock. Useful for locking blocks of data into the data cache for time-critical
applications where deterministic behavior is required. See Section 2.4.2.3, “Cache Locking.”
—
Reserved
Processor Version Register (PVR)
Software can identify the MPC8280’s processor core by reading the processor version register (PVR). The
processor version number is 0x80822013.
2.3.2
PowerPC Instruction Set and Addressing Modes
All PowerPC instructions are encoded as single-word (32-bit) opcodes. Instruction formats are consistent
among all instruction types, permitting efficient decoding to occur in parallel with operand accesses. This
fixed instruction length and consistent format greatly simplifies instruction pipelining.
2.3.2.1
Calculating Effective Addresses
The effective address (EA) is the 32-bit address computed by the processor when executing a memory
access or branch instruction or when fetching the next sequential instruction.
The PowerPC architecture supports two simple memory addressing modes:
• EA = (rA|0) + offset (including offset = 0) (register indirect with immediate index)
• EA = (rA|0) + rB (register indirect with index)
These simple addressing modes allow efficient address generation for memory accesses. Calculation of the
effective address for aligned transfers occurs in a single clock cycle.
For a memory access instruction, if the sum of the effective address and the operand length exceeds the
maximum effective address, the memory operand is considered to wrap around from the maximum
effective address to effective address 0.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
2-15
G2_LE Core
Effective address computations for both data and instruction accesses use 32-bit unsigned binary
arithmetic. A carry from bit 0 is ignored in 32-bit implementations.
In addition to the functionality of the MPC603e, the MPC8280 has additional hardware support for
misaligned little-endian accesses. Except for string/multiple load and store instructions, little-endian
load/store accesses not on a word boundary generate exceptions under the same circumstances as
big-endian requests.
2.3.2.2
PowerPC Instruction Set
The PowerPC instructions are divided into the following categories:
• Integer instructions—These include arithmetic and logical instructions.
— Integer arithmetic
— Integer compare
— Integer logical
— Integer rotate and shift
• Floating-point instructions—These include floating-point computational instructions, as well as
instructions that affect the FPSCR.
— Floating-point arithmetic
— Floating-point multiply/add
— Floating-point rounding and conversion
— Floating-point compare
— Floating-point status and control
• Load/store instructions—These include integer and floating-point load and store instructions.
— Integer load and store
— Integer load and store with byte reverse
— Integer load and store string/multiple
— Floating-point load and store
• Flow control instructions—These include branching instructions, condition register logical
instructions, trap instructions, and other synchronizing instructions that affect the instruction flow.
— Branch and trap
— Condition register logical
— Primitives used to construct atomic memory operations (lwarx and stwcx.)
— Synchronize
• Processor control instructions—These instructions are used for synchronizing memory accesses
and management of caches, TLBs, and the segment registers.
— Move to/from SPR
— Move to/from MSR
— Instruction synchronize
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
2-16
Freescale Semiconductor
G2_LE Core
•
•
Memory control instructions—These provide control of caches, TLBs, and segment registers.
— Supervisor-level cache management
— User-level cache management
— Segment register manipulation
— TLB management
The G2_LE core implements the following instructions, which are defined as optional by the
PowerPC architecture:
— External Control In Word Indexed (eciwx)
— External Control Out Word Indexed (ecowx)
— Floating Select (fsel)
— Floating Reciprocal Estimate Single-Precision (fres)
— Floating Reciprocal Square Root Estimate (frsqrte)
— Store Floating-Point as Integer Word (stfiwx)
Note that this grouping of the instructions does not indicate which execution unit executes a particular
instruction or group of instructions.
Integer instructions operate on byte, half-word, and word operands. The PowerPC architecture uses
instructions that are four bytes long and word-aligned. It provides for byte, half-word, and word operand
loads and stores between memory and a set of 32 GPRs. Floating-point instructions operate on
single-precision (one word) and double-precision (one double word) floating-point operands. It also
provides for word and double-word operand loads and stores between memory and a set of 32
floating-point registers (FPRs).
Computational instructions do not modify memory. To use a memory operand in a computation and then
modify the same or another memory location, the memory contents must be loaded into a register,
modified, and written back to the target location with separate instructions. Decoupling arithmetic
instructions from memory accesses increases throughput by facilitating pipelining.
Processors that implement the PowerPC architecture follow the program flow when they are in the normal
execution state. However, the flow of instructions can be interrupted directly by the execution of an
instruction or by an asynchronous event. Either kind of exception may cause one of several components
of the system software to be invoked.
2.3.2.3
MPC8280 Implementation-Specific Instruction Set
The G2_LE core instruction set is defined as follows:
• The core provides hardware support for all 32-bit PowerPC instructions.
• The core provides the following two implementation-specific instructions used for software
tablesearch operations following TLB misses:
— Load Data TLB Entry (tlbld)
— Load Instruction TLB Entry (tlbli)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
2-17
G2_LE Core
•
2.4
The G2_LE implements the following instruction, which supports critical interrupts. This is a
supervisor-level, context synchronizing instruction.
— Return from Critical Interrupt (rfci)
Cache Implementation
The MPC8280 processor core has separate data and instruction caches. The cache implementation is
described in the following sections.
2.4.1
PowerPC Cache Model
The PowerPC architecture does not define hardware aspects of cache implementations. For example, some
processors, including the MPC8280’s processor core, have separate instruction and data caches (Harvard
architecture), while others implement a unified cache.
Microprocessors that implement the PowerPC architecture control the following memory access modes on
a page or block basis:
• Write-back/write-through mode
• Caching-inhibited mode
• Memory coherency
The PowerPC cache management instructions provide a means by which the application programmer can
affect the cache contents.
2.4.2
MPC8280 Implementation-Specific Cache Implementation
As shown in Figure 2-1, the caches provide a 64-bit interface to the instruction fetch unit and load/store
unit. The surrounding logic selects, organizes, and forwards the requested information to the requesting
unit. Write operations to the cache can be performed on a byte basis, and a complete read-modify-write
operation to the cache can occur in each cycle.
Each cache block contains eight contiguous words from memory that are loaded from an 8-word boundary
(that is, bits A27–A31 of the effective addresses are zero); thus, a cache block never crosses a page
boundary. Misaligned accesses across a page boundary can incur a performance penalty.
The cache blocks are loaded in to the processor core in four beats of 64 bits each. The burst load is
performed as critical double word first.
To ensure coherency among caches in a multiprocessor (or multiple caching-device) implementation, the
processor core implements the MEI protocol. These three states, modified, exclusive, and invalid, indicate
the state of the cache block as follows:
• Modified—The cache block is modified with respect to system memory; that is, data for this
address is valid only in the cache and not in system memory.
• Exclusive—This cache block holds valid data that is identical to the data at this address in system
memory. No other cache has this data.
• Invalid—This cache block does not hold valid data.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
2-18
Freescale Semiconductor
G2_LE Core
2.4.2.1
Data Cache
As shown in Figure 2-6, the data cache is configured as 128 sets of four blocks each. Each block consists
of 32 bytes, two state bits, and an address tag. The two state bits implement the three-state MEI
(modified/exclusive/invalid) protocol. Each block contains eight 32-bit words. Note that the PowerPC
architecture defines the term ‘block’ as a cacheable unit. For the MPC8280’s processor core, the block size
is equivalent to a cache line.
128 Sets
Block 0
Address Tag 0
State
Words 0–7
Block 1
Address Tag 1
State
Words 0–7
Block 2
Address Tag 2
State
Words 0–7
Block 3
Address Tag 3
State
Words 0–7
8 Words/Block
Figure 2-6. Data Cache Organization
Because the processor core data cache tags are single-ported, simultaneous load or store and snoop
accesses cause resource contention. Snoop accesses have the highest priority and are given first access to
the tags, unless the snoop access coincides with a tag write, in which case the snoop is retried and must
rearbitrate for access to the cache. Loads or stores that are deferred due to snoop accesses are executed on
the clock cycle following the snoop.
Because the caches on the processor core are write-back caches, the predominant type of transaction for
most applications is burst-read memory operations, followed by burst-write memory operations, and
single-beat (noncacheable or write-through) memory read and write operations. When a cache block is
filled with a burst read, the critical double word is simultaneously written to the cache and forwarded to
the requesting unit, thus minimizing stalls due to load delays.
Additionally, there can be address-only operations, variants of the burst and single-beat operations, (for
example, global memory operations that are snooped and atomic memory operations), and address retry
activity (for example, when a snooped read access hits a modified line in the cache).
Setting HID0[ABE] causes execution of the dcbf, dcbi, and dcbst instructions to be broadcast onto the
60x bus. The value of ABE does not affect dcbz instructions, which are always broadcast and snooped.
The cache operations are intended primarily for managing on-chip caches. However, the optional
broadcast feature is necessary to allow proper management of a system using an external copyback L2
cache.
The address and data buses operate independently to support pipelining and split transactions during
memory accesses. The processor core pipelines its own transactions to a depth of one level.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
2-19
G2_LE Core
Typically, memory accesses are weakly ordered—sequences of operations, including load/store string and
multiple instructions, do not necessarily complete in the order they begin—maximizing the efficiency of
the internal bus without sacrificing coherency of the data. The processor core allows pending read
operations to precede previous store operations (except when a dependency exists, or in cases where a
non-cacheable access is performed), and provides support for a write operation to precede a previously
queued read data tenure (for example, allowing a snoop push to be enveloped by the address and data
tenures of a read operation). Because the processor can dynamically optimize run-time ordering of
load/store traffic, overall performance is improved.
2.4.2.2
Instruction Cache
The instruction cache also consists of 128 sets of four blocks, and each block consists of 32 bytes, an
address tag, and a valid bit. The instruction cache may not be written to except through a block fill
operation caused by a cache miss. In the processor core, internal access to the instruction cache is blocked
only until the critical load completes.
The processor core supports instruction fetching from other instruction cache lines following the
forwarding of the critical first double word of a cache line load operation. The processor core’s instruction
cache is blocked only until the critical load completes (hits under reloads are allowed). Successive
instruction fetches from the cache line being loaded are forwarded, and accesses to other instruction cache
lines can proceed during the cache line load operation.
The instruction cache is not snooped, and cache coherency must be maintained by software. A fast
hardware invalidation capability is provided to support cache maintenance. The organization of the
instruction cache is very similar to the data cache shown in Figure 2-6.
2.4.2.3
Cache Locking
The processor core supports cache locking, which is the ability to prevent some or all of a microprocessor’s
instruction or data cache from being overwritten. Cache entries can be locked for either an entire cache or
for individual ways within the cache. Entire data cache locking is enabled by setting HID0[DLOCK], and
entire instruction cache locking is enabled by setting HID0[ILOCK]. For more information, refer to the
application note Cache Locking on the G2 Core (order number: AN1767). Cache way locking is controlled
by the IWLCK and DWLCK bits of HID2.
2.4.2.3.1
Entire Cache Locking
When an entire cache is locked, hits within the cache are supplied in the same manner as hits to an
unlocked cache. Any access that misses in the cache is treated as a cache-inhibited access. Cache entries
that are invalid at the time of locking will remain invalid and inaccessible until the cache is unlocked. Once
the cache has been unlocked, all entries (including invalid entries) are available. Entire cache locking is
inefficient if the number of instructions or the size of data to be locked is small compared to the cache size.
2.4.2.3.2
Way Locking
Locking only a portion of the cache is accomplished by locking ways within the cache. Locking always
begins with the first way (way0) and is sequential, that is, it is valid to lock ways 0, 1, and 2 but it is not
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
2-20
Freescale Semiconductor
G2_LE Core
possible to lock just way0 and way2. When using way locking at least one way must be left unlocked. The
maximum number of lockable ways is three.
Unlike entire cache locking, invalid entries in a locked way are accessible and available for data
placement. As hits to the cache fill invalid entries within a locked way, the entries become valid and
locked. This behavior differs from entire cache locking, where nothing is placed in the cache, even if
invalid entries exist in the cache. Unlocked ways of the cache behave normally.
2.5
Exception Model
This section describes the PowerPC exception model and implementation-specific details of the MPC8280
core.
2.5.1
PowerPC Exception Model
The PowerPC exception mechanism allows the processor to change to supervisor state as a result of
external signals, errors, or unusual conditions arising in the execution of instructions. When exceptions
occur, information about the state of the processor is saved to certain registers and the processor begins
execution at an address (exception vector) predetermined for each exception. Processing of exceptions
occurs in supervisor mode.
Although multiple exception conditions can map to a single exception vector, a more specific condition
may be determined by examining a register associated with the exception—for example, the DSISR
identifies instructions that cause a DSI exception. Additionally, some exception conditions can be
explicitly enabled or disabled by software.
The PowerPC architecture requires that exceptions be handled in program order; therefore, although a
particular implementation may recognize exception conditions out of order, exceptions are taken in strict
order. When an instruction-caused exception is recognized, any unexecuted instructions that appear earlier
in the instruction stream, including any that have not yet entered the execute stage, are required to complete
before the exception is taken. Any exceptions caused by those instructions are handled first. Likewise,
exceptions that are asynchronous and precise are recognized when they occur, but are not handled until the
instruction currently in the completion stage successfully completes execution or generates an exception,
and the completed store queue is emptied.
Unless a catastrophic condition causes a system reset or machine check exception, only one exception is
handled at a time. If, for example, a single instruction encounters multiple exception conditions, those
conditions are handled sequentially. After the exception handler handles an exception, the instruction
execution continues until the next exception condition is encountered. However, in many cases there is no
attempt to re-execute the instruction. This method of recognizing and handling exception conditions
sequentially guarantees that exceptions are recoverable.
Exception handlers should save the information stored in SRR0 and SRR1 early to prevent the program
state from being lost due to a system reset or machine check exception or to an instruction-caused
exception in the exception handler. SRR0 and SRR1 should also be saved before enabling external
interrupts.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
2-21
G2_LE Core
The PowerPC architecture supports four types of exceptions:
• Synchronous, precise—These are caused by instructions. All instruction-caused exceptions are
handled precisely; that is, the machine state at the time the exception occurs is known and can be
completely restored. This means that (excluding the trap and system call exceptions) the address
of the faulting instruction is provided to the exception handler and that neither the faulting
instruction nor subsequent instructions in the code stream will complete execution before the
exception is taken. Once the exception is processed, execution resumes at the address of the
faulting instruction (or at an alternate address provided by the exception handler). When an
exception is taken due to a trap or system call instruction, execution resumes at an address provided
by the handler.
• Synchronous, imprecise—The PowerPC architecture defines two imprecise floating-point
exception modes: recoverable and nonrecoverable. Even though the G2_LE core provides a means
to enable the imprecise modes, it implements these modes identically to the precise mode (that is,
all enabled floating-point enabled exceptions are always precise on the core).
• Asynchronous, maskable—The external, system management interrupt (SMI), and decrementer
interrupts are maskable asynchronous exceptions. When these exceptions occur, their handling is
postponed until the next instruction and any exceptions associated with that instruction complete
execution. If no instructions are in the execution units, the exception is taken immediately upon
determination of the correct restart address (for loading SRR0).
• Asynchronous, nonmaskable—There are two nonmaskable asynchronous exceptions: system reset
and the machine check exception. These exceptions may not be recoverable, or may provide a
limited degree of recoverability. All exceptions report recoverability through MSR[RI].
2.5.2
Implementation-Specific Exception Model
As specified by the PowerPC architecture, all processor core exceptions can be described as either precise
or imprecise and either synchronous or asynchronous. Asynchronous exceptions (some of which are
maskable) are caused by events external to the processor’s execution. Synchronous exceptions, which are
all handled precisely by the processor core, are caused by instructions. The processor core exception
classes are shown in Table 2-4.
Table 2-4. Exception Classifications for the Processor Core
Synchronous/Asynchronous
Precise/Imprecise
Exception Type
Imprecise
Machine check
System reset
Asynchronous, maskable
Precise
External interrupt
Decrementer
System management interrupt
Critical interrupt
Synchronous
Precise
Instruction-caused exceptions
Asynchronous, nonmaskable
Although exceptions have other characteristics as well, such as whether they are maskable or
nonmaskable, the distinctions shown in Table 2-4 define categories of exceptions that the processor core
handles uniquely. Note that Table 2-4 includes no synchronous imprecise instructions.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
2-22
Freescale Semiconductor
G2_LE Core
The processor core’s exceptions, and conditions that cause them, are listed in Table 2-5.
Table 2-5. Exceptions and Conditions
Exception
Type
Vector Offset
(hex)
Causing Conditions
Reserved
00000
—
System reset
00100
A system reset is caused by the assertion of either SRESET or HRESET. Note that
the reset value of the MSR exception prefix bit (MSR[IP]), described in the G2 Core
Reference Manual, is determined by the CIP bit in the hard reset configuration word.
This is described in Section 5.4.1, “Hard Reset Configuration Word.”
Machine check 00200
A machine check is caused by the assertion of the TEA signal during a data bus
transaction, assertion of MCP, or an address or data parity error.
DSI
00300
The cause of a DSI exception can be determined by the bit settings in the DSISR,
listed as follows:
1 Set if the translation of an attempted access is not found in the primary hash table
entry group (HTEG), or in the rehashed secondary HTEG, or in the range of a
DBAT register; otherwise cleared.
4 Set if a memory access is not permitted by the page or DBAT protection
mechanism; otherwise cleared.
5 Set by an eciwx or ecowx instruction if the access is to an address that is
marked as write-through, or execution of a load/store instruction that accesses a
direct-store segment.
6 Set for a store operation and cleared for a load operation.
11 Set if eciwx or ecowx is used and EAR[E] is cleared.
ISI
00400
An ISI exception is caused when an instruction fetch cannot be performed for any of
the following reasons:
• The effective (logical) address cannot be translated. That is, there is a page fault
for this portion of the translation, so an ISI exception must be taken to load the
PTE (and possibly the page) into memory.
• The fetch access is to a direct-store segment (indicated by SRR1[3] set).
• The fetch access violates memory protection (indicated by SRR1[4] set). If the key
bits (Ks and Kp) in the segment register and the PP bits in the PTE are set to
prohibit read access, instructions cannot be fetched from this location.
External
interrupt
00500
An external interrupt is caused when MSR[EE] = 1 and the INT signal is asserted.
Alignment
00600
An alignment exception is caused when the processor core cannot perform a
memory access for any of the reasons described below:
• The operand of a floating-point load or store is to a direct-store segment.
• The operand of a floating-point load or store is not word-aligned.
• The operand of a lmw, stmw, lwarx, or stwcx. is not word-aligned.
• The operand of an elementary, multiple or string load or store crosses a segment
boundary with a change to the direct store T bit.
• The operand of dcbz instruction is in memory that is write-through required or
caching inhibited, or dcbz is executed in an implementation that has either no
data cache or a write-through data cache.
• A misaligned eciwx or ecowx instruction
• A multiple or string access with MSR[LE] set
The processor core differs from MPC603e User’s Manual in that it initiates an
alignment exception when it detects a misaligned eciwx or ecowx instruction and
does not initiate an alignment exception when a little-endian access is misaligned.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
2-23
G2_LE Core
Table 2-5. Exceptions and Conditions (continued)
Exception
Type
Vector Offset
(hex)
Causing Conditions
Program
00700
A program exception is caused by one of the following exception conditions, which
correspond to bit settings in SRR1 and arise during execution of an instruction:
• Illegal instruction—An illegal instruction program exception is generated when
execution of an instruction is attempted with an illegal opcode or illegal
combination of opcode and extended opcode fields (including PowerPC
instructions not implemented in the processor core), or when execution of an
optional instruction not provided in the processor core is attempted (these do not
include those optional instructions that are treated as no-ops).
• Privileged instruction—A privileged instruction type program exception is
generated when the execution of a privileged instruction is attempted and the
MSR register user privilege bit, MSR[PR], is set. In the processor core, this
exception is generated for mtspr or mfspr with an invalid SPR field if SPR[0] = 1
and MSR[PR] = 1. This may not be true for all processors that implement the
PowerPC architecture.
• Trap—A trap type program exception is generated when any of the conditions
specified in a trap instruction is met.
Floating-point
unavailable
00800
A floating-point unavailable exception is caused by an attempt to execute a
floating-point instruction (including floating-point load, store, and move instructions)
when the floating-point available bit is cleared (MSR[FP] = 0).
Decrementer
00900
The decrementer exception occurs when the most significant bit of the decrementer
(DEC) register transitions from 0 to 1. Must also be enabled with the MSR[EE] bit.
Critical
interrupt
00A00
A critical interrupt is caused when MSR[CE] = 1 and the CINT signal is asserted.
Reserved
00B00–00BFF —
System call
00C00
A system call exception occurs when a System Call (sc) instruction is executed.
Trace
00D00
A trace exception is taken when MSR[SE] = 1 or when the currently completing
instruction is a branch and MSR[BE] = 1.
Floating-point
assist
00E00
Not implemented.
Reserved
00E10–00FFF —
Instruction
translation
miss
01000
An instruction translation miss exception is caused when the effective address for an
instruction fetch cannot be translated by the ITLB.
Data load
translation
miss
01100
A data load translation miss exception is caused when the effective address for a
data load operation cannot be translated by the DTLB.
Data store
translation
miss
01200
A data store translation miss exception is caused when the effective address for a
data store operation cannot be translated by the DTLB, or when a DTLB hit occurs,
and the changed bit in the PTE must be set due to a data store operation.
Instruction
address
breakpoint
01300
An instruction address breakpoint exception occurs when the address (bits 0–29) in
the IABR matches the next instruction to complete in the completion unit, and the
IABR enable bit (bit 30) is set.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
2-24
Freescale Semiconductor
G2_LE Core
Table 2-5. Exceptions and Conditions (continued)
Exception
Type
Vector Offset
(hex)
Causing Conditions
System
management
interrupt
01400
A system management interrupt is caused when MSR[EE] = 1 and the SMI input
signal is asserted.
Reserved
01500–02FFF
—
2.6
Memory Management
The following subsections describe the memory management unit (MMU) features of the PowerPC
architecture and the G2_LE implementation.
2.6.1
PowerPC Memory Management
The primary functions of the MMU are to translate logical (effective) addresses to physical addresses for
memory accesses and to provide access protection on blocks and pages of memory.
The core generates two types of accesses that require address translation: instruction accesses and data
accesses to memory generated by load and store instructions.
The PowerPC MMU and exception model support demand-paged virtual memory. Virtual memory
management permits execution of programs larger than the size of physical memory; demand-paged
memory implies that individual pages are loaded into physical memory from system memory only when
they are first accessed by an executing program.
The hashed page table is a variable-sized data structure that defines the mapping between virtual page
numbers and physical page numbers. The page table size is a power of two, and its starting address is a
multiple of its size.
The page table contains a number of page table entry groups (PTEGs). A PTEG contains eight page table
entries (PTEs) of 8 bytes each; therefore, each PTEG is 64 bytes long. PTEG addresses are entry points for
table search operations.
Address translations are enabled by setting bits in the MSR. MSR[IR] enables instruction address
translations, and MSR[DR] enables data address translations.
2.6.2
Implementation-Specific MMU Features
The instruction and data memory management units in the G2_LE core provide 4 Gbytes of logical address
space accessible to supervisor and user programs with a 4-Kbyte page size and 256-Mbyte segment size.
Block sizes range from 128 Kbytes to 256 Mbytes and are software selectable. In addition, the core uses
an interim 52-bit virtual address and hashed page tables for generating 32-bit physical addresses. The
MMUs in the G2_LE core rely on the exception processing mechanism for the implementation of the
paged virtual memory environment and for enforcing protection of designated memory areas.
Instruction and data TLBs provide address translation in parallel with the on-chip cache access, incurring
no additional time penalty in the event of a TLB hit. A TLB is a cache of the most recently used page table
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
2-25
G2_LE Core
entries. Software is responsible for maintaining the consistency of the TLB with memory. The core TLBs
are 64-entry, two-way set-associative caches that contain instruction and data address translations. The
core provides hardware assist for software table search operations through the hashed page table on TLB
misses. Supervisor software can invalidate TLB entries selectively.
For instructions and data that maintain address translations for blocks of memory, the G2_LE core
provides independent eight-entry BAT arrays. These entries define blocks that can vary from 128 Kbytes
to 256 Mbytes. The BAT arrays are maintained by system software. Adding the HID2[HBE] to the G2_LE
enables or disables the four additional pairs of BAT registers. However, regardless of the setting of
HID2[HBE], these BATs are accessible by mfspr and mtspr.
As specified by the PowerPC architecture, the hashed page table is a variable-sized data structure that
defines the mapping between virtual page numbers and physical page numbers. The page table size is a
power of two, and its starting address is a multiple of its size.
As specified by the PowerPC architecture, the page table contains a number of PTEGs. A PTEG contains
eight PTEs of 8 bytes each; therefore, each PTEG is 64 bytes long. PTEG addresses are entry points for
table search operations.
2.7
Instruction Timing
The G_LE2 core is a pipelined superscalar processor core. Because instruction processing is reduced into
a series of stages, an instruction does not require all of the resources of an execution unit at the same time.
For example, after an instruction completes the decode stage, it can pass on to the next stage, while the
subsequent instruction can advance into the decode stage. This improves the throughput of the instruction
flow. For example, it may take three cycles for a single floating-point instruction to execute, but if there
are no stalls in the floating-point pipeline, a series of floating-point instructions can have a throughput of
one instruction per cycle.
The core instruction pipeline has four major pipeline stages, described as follows:
• The fetch pipeline stage primarily involves retrieving instructions from the memory system and
determining the location of the next instruction fetch. Additionally, if possible, the BPU decodes
branches during the fetch stage and folds out branch instructions before the dispatch stage.
• The dispatch pipeline stage is responsible for decoding the instructions supplied by the instruction
fetch stage, and determining which of the instructions are eligible to be dispatched in the current
cycle. In addition, the source operands of the instructions are read from the appropriate register file
and dispatched with the instruction to the execute pipeline stage. At the end of the dispatch pipeline
stage, the dispatched instructions and their operands are latched by the appropriate execution unit.
• In the execute pipeline stage, each execution unit with an executable instruction executes the
selected instruction (perhaps over multiple cycles), writes the instruction's result into the
appropriate rename register, and notifies the completion stage when the execution has finished. In
the case of an internal exception, the execution unit reports the exception to the
completion/write-back pipeline stage and discontinues instruction execution until the exception is
handled. The exception is not signaled until that instruction is the next to be completed. Execution
of most floating-point instructions is pipelined within the FPU allowing up to three instructions to
be executing in the FPU concurrently. The FPU pipeline stages are multiply, add, and
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
2-26
Freescale Semiconductor
G2_LE Core
•
round-convert. The LSU has two pipeline stages. The first stage is for effective address calculation
and MMU translation, and the second is for accessing data in the cache.
The complete/write-back pipeline stage maintains the correct architectural machine state and
transfers the contents of the rename registers to the GPRs and FPRs as instructions are retired. If
the completion logic detects an instruction causing an exception, all following instructions are
canceled, their execution results in rename registers are discarded, and instructions are fetched
from the correct instruction stream.
A superscalar processor core issues multiple independent instructions into multiple pipelines allowing
instructions to execute in parallel. The G2_LE core has five independent execution units, one each for
integer instructions, floating-point instructions, branch instructions, load/store instructions, and system
register instructions. The IU and the FPU each have dedicated register files for maintaining operands
(GPRs and FPRs, respectively), allowing integer and floating-point calculations to occur simultaneously
without interference. Integer division performance of the G2_LE core has been improved, with the divwux
and divwx instructions executing in 20 clock cycles instead of the 37 cycles required in the MPC603e.
The core provides support for single-cycle store and an adder/comparator in the system register unit that
allows the dispatch and execution of multiple integer add and compare instructions on each cycle.
Because the PowerPC architecture can be applied to such a wide variety of implementations, instruction
timing among processor cores varies accordingly.
2.8
Differences Between the MPC8280 G2_LE
Embedded Core and the MPC603e
The G2_LE processor core is a derivative of the MPC603e microprocessor design. Some changes have
been made and are visible either to a programmer or a system designer. Any software designed around an
MPC603e is functional when replaced with the G2_LE except for the specific customer-visible changes
listed in Table 2-6.
Software can distinguish between the MPC603e and the G2_LE by reading the processor version register
(PVR). The G2_LE processor version number is 0x0081; the processor revision level starts at 0x0100 and
is incremented for each revision of the chip.
Table 2-6. Differences Between G2_LE Core and MPC603e
Description
Impact
An additional input interrupt signal, CINT, MSR[CE] is allocated for enabling the critical interrupt
implements a critical interrupt function.
A new instruction is implemented for
critical interrupt
Return from Critical Interrupt (rfci) is implemented to return from these exception
handlers
Vector offset for critical interrupt
An exception vector offset of 0x00A00 is defined for critical interrupt
Two new registers are implemented for
saving processor state for critical
interrupts
CSRR0 and CSRR1 have the same bit assignments as SRR0 and SRR1,
respectively.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
2-27
G2_LE Core
Table 2-6. Differences Between G2_LE Core and MPC603e (continued)
Description
Impact
Implements a cache way locking mechanism for both the instruction and data
Supports instruction and data cache
way-locking in addition to entire instruction caches. One to three of the four ways in the cache can be locked with control bits
in the HID2 register. See Section 2.3.1.2.3, “Hardware
and data cache locking
Implementation-Dependent Register 2 (HID2).”
Four additional SPRG registers
The additional SPRGs reduce latencies that may be incurred from saving
registers to memory while in an exception handler
One new address breakpoint register
IABR2
Instruction address breakpoint exceptions in both the MPC603e and the G2_LE
cores use the 0x01300 vector offset
Two new data address breakpoint
registers are implemented in the G2_LE
The two new data address breakpoint registers (DABR and DABR2) expand the
debug functionality of the breakpoints. The new breakpoint registers are
accessible as SPRs with mtspr and mfspr.
One instruction register and one data
breakpoint control register are
implemented
IBCR and DBCR are implemented to support the additional debug features.
These registers are accessible as SPRs with mtspr and mfspr.
Vector offset for data address breakpoint
exception is 0x00300
Data address breakpoint exception is a DSI exception. The cause of a DSI
exception can be determined by the bit settings of DSISR[9]. DAR contains the
address of the breakpoint match condition.
One new register is implemented for
supporting system level memory map
System memory base address register (MBAR) can be accessed with mtspr or
mfspr using SPR311 in supervisor mode. It can store the present memory base
address for the system memory map.
The G2_LE has eight pairs of data and
eight pairs of instruction BAT registers
IBAT4–IBAT7 are the four additional pairs of instruction BATs and DBAT4–DBAT7
are the four additional data BATs. HID2[HBE] is added for enabling or disabling
the four additional pairs of BAT registers. These BATs are accessible by the mfspr
and mtspr instructions regardless of the setting of HID2[HBE].
Added hardware support for misaligned
little endian accesses
Except for strings/multiples, little-endian load/store accesses not on a word
boundary generate exceptions under the same circumstances as big-endian
accesses.
Removed misalignment support for eciwx These instructions take an alignment exception if not on a word boundary.
and ecowx instructions
Added ability to broadcast dcbf, dcbi, and Setting HID0[ABE] enables the new broadcast feature (new in the PID7v-603e).
dcbst onto the 60x bus
The default is to not broadcast these operations.
Added ability to reflect the value of the M
bit onto the 60x bus during instruction
translations
Setting HID0[IFEM] enables this feature. The default is to not present the M bit on
the bus.
Removed HID0[EICE]
There is no support for ICE pipeline tracking.
Added pin-configurable reset vector
The value of MSR[IP], interrupt prefix, is determined at hard reset by the hardware
configuration word.
Addition of speed-for-power functionality
The processor core implements an additional dynamic power management
mechanism. HID2[SFP] controls this function. See Section 2.3.1.2.3, “Hardware
Implementation-Dependent Register 2 (HID2).”
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
2-28
Freescale Semiconductor
Chapter 3
Memory Map
The MPC8280’s internal memory resources are mapped within a contiguous block of memory. The size of
the internal space is 256 Kbytes. The location of this block within the global 4-Gbyte real memory space
can be mapped on 256-Kbytes resolution through an implementation-specific special register called the
internal memory map register (IMMR). For more information, see Section 4.3.2.7, “Internal Memory Map
Register (IMMR).”
Figure 3-1 shows the internal memory resources.
DPRAM1
Global memory1
0
0x0_0000
Dual-Port
RAM
1 Gbyte
16 Kbytes
DPRAM2
16 Kbytes
0x1_0000
(see note 2)
2 Gbyte
0x2_0000
IRAM
3 Gbyte
32 Kbytes
0x3_0000
SIU
Memory
controller
PCI
4 Gbyte
0x4_0000
Interrupt
controller
Clocks/Reset
I/O ports
The location of the 256-Kbyte block of internal memory within global memory
is selected according to the internal memory map register (IMMR). Internal
memory must be mapped on 256-Kbyte resolution.
1 Location of internal memory resources in this figure is for illustration only.
2 The right vertical column is for illustration only. For a complete list of
modules and registers, refer to Table 3-1.
CPM
CPM
interface
Serial
interface
Figure 3-1. Internal Memory
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
3-1
Memory Map
3.1
Internal Memory Map
Table 3-1 defines the internal memory map of the MPC8280.
Table 3-1. Internal Memory Map
Address
(offset)
Register
R/W
Size
Reset
Section/Page
R/W
16
Kbytes
—
14.5/14-17
—
16
Kbytes
—
—
R/W
16
Kbytes
—
14.5/14-17
—
16
Kbytes
—
—
CPM Dual-Port RAM (Data)
0x00000– Dual-port RAM (DPRAM1)
0x03FFF
0x04000– Reserved
0x07FFF
0x08000– Dual-port RAM (DPRAM2)
0x0BFFF
0x0C000– Reserved
0x0FFFF
General SIU
0x10000
SIU module configuration register (SIUMCR)
R/W
32 bits
see
Figure 4-28
4.3.2.6/4-33
0x10004
System protection control register (SYPCR)
R/W
32 bits
0xFFFF_FF07
4.3.2.8/4-37
0x10008
Reserved
—
6 bytes
—
—
0x1000E
Software service register (SWSR)
W
16 bits
undefined
4.3.2.9/4-38
—
20 bytes
—
—
0x10010– Reserved
0x10023
0x10024
Bus configuration register (BCR)
R/W
32 bits
reset
configuration
4.3.2.1/4-26
0x10028
60x bus arbiter configuration register (PPC_ACR)
R/W
8 bits
see
Figure 4-22
4.3.2.2/4-29
0x10029
Reserved
—
24 bits
—
—
0x1002C
60x bus arbitration-level register high (first 8 clients)
(PPC_ALRH)
R/W
32 bits
0x0126_3457
4.3.2.3/4-30
0x10030
60x bus arbitration-level register low (next 8 clients)
(PPC_ALRL)
R/W
32 bits
0x89AB_CDEF
4.3.2.3/4-30
0x10034
Local arbiter configuration register (LCL_ACR)
R/W
8 bits
0x02
4.3.2.4/4-31
0x10035
Reserved
—
24 bits
—
—
0x10038
Local arbitration-level register (first 8 clients) (LCL_ALRH)
R/W
32 bits
0x0126_3457
4.3.2.5/4-32
0x1003C
Local arbitration-level register (next 8 clients) (LCL_ALRL)
R/W
32 bits
0x89AB_
CDEF
4.3.2.3/4-30
0x10040
60x bus transfer error status control register 1 (TESCR1)
R/W
32 bits
0x0000_0000
4.3.2.10/4-39
0x10044
60x bus transfer error status control register 2 (TESCR2)
R/W
32 bits
0x0000_0000
4.3.2.11/4-41
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
3-2
Freescale Semiconductor
Memory Map
Table 3-1. Internal Memory Map (continued)
Address
(offset)
Register
R/W
Size
Reset
Section/Page
0x10048
Local bus transfer error status control register 1 (L_TESCR1) R/W
32 bits
0x0000_0000
4.3.2.12/4-42
0x1004C
Local bus transfer error status control register 2 (L_TESCR2) R/W
32 bits
0x0000_0000
4.3.2.13/4-43
0x10050
60x bus DMA transfer error address (PDTEA)
R
32 bits
undefined
19.2.3/19-4
0x10054
60x bus DMA transfer error MSNUM (PDTEM)
R
8 bits
undefined
19.2.4/19-4
0x10055
Reserved
—
24 bits
—
—
0x10058
Local bus DMA transfer error address (LDTEA)
R
32 bits
undefined
19.2.3/19-4
0x1005C
Local bus DMA transfer error MSNUM (LDTEM)
R
8 bits
undefined
19.2.4/19-4
—
163
bytes
—
—
0x1005D– Reserved
0x100FF
Memory Controller
0x10100
Base register bank 0 (BR0)
R/W
32 bits
see
Figure 11-6
11.3.1/11-13
0x10104
Option register bank 0 (OR0)
R/W
32 bits
0xFE00_0EF4
11.3.2/11-15
0x10108
Base register bank 1 (BR1)
R/W
32 bits
0x0000_0000
11.3.1/11-13
0x1010C
Option register bank 1 (OR1)
R/W
32 bits
undefined
11.3.2/11-15
0x10110
Base register bank 2 (BR2)
R/W
32 bits
0x0000_0000
11.3.1/11-13
0x10114
Option register bank 2 (OR2)
R/W
32 bits
undefined
11.3.2/11-15
0x10118
Base register bank 3 (BR3)
R/W
32 bits
0x0000_0000
11.3.1/11-13
0x1011C
Option register bank 3 (OR3)
R/W
32 bits
undefined
11.3.2/11-15
0x10120
Base register bank 4 (BR4)
R/W
32 bits
0x0000_0000
11.3.1/11-13
0x10124
Option register bank 4 (OR4)
R/W
32 bits
undefined
11.3.2/11-15
0x10128
Base register bank 5 (BR5)
R/W
32 bits
0x0000_0000
11.3.1/11-13
0x1012C
Option register bank 5 (OR5)
R/W
32 bits
undefined
11.3.2/11-15
0x10130
Base register bank 6 (BR6)
R/W
32 bits
0x0000_0000
11.3.1/11-13
0x10134
Option register bank 6 (OR6)
R/W
32 bits
undefined
11.3.2/11-15
0x10138
Base register bank 7 (BR7)
R/W
32 bits
0x0000_0000
11.3.1/11-13
0x1013C
Option register bank 7 (OR7)
R/W
32 bits
undefined
11.3.2/11-15
0x10140
Base register bank 8 (BR8)
R/W
32 bits
0x0000_0000
11.3.1/11-13
0x10144
Option register bank 8 (OR8)
R/W
32 bits
undefined
11.3.2/11-15
0x10148
Base register bank 9 (BR9)
R/W
32 bits
0x0000_0000
11.3.1/11-13
0x1014C
Option register bank 9 (OR9)
R/W
32 bits
undefined
11.3.2/11-15
0x10150
Base register bank 10 (BR10)
R/W
32 bits
0x0000_0000
11.3.1/11-13
0x10154
Option register bank 10 (OR10)
R/W
32 bits
undefined
11.3.2/11-15
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
3-3
Memory Map
Table 3-1. Internal Memory Map (continued)
Address
(offset)
Register
R/W
Size
Reset
Section/Page
0x10158
Base register bank 11 (BR11)
R/W
32 bits
0x0000_0000
11.3.1/11-13
0x1015C
Option register bank 11 (OR11)
R/W
32 bits
undefined
11.3.2/11-15
0x10160
Reserved
—
8 bytes
—
—
0x10168
Memory address register (MAR)
R/W
32 bits
undefined
11.3.7/11-29
0x1016C
Reserved
—
32 bits
—
—
0x10170
Machine A mode register (MAMR)
R/W
32 bits
0x0004_0000
11.3.5/11-26
0x10174
Machine B mode register (MBMR)
R/W
32 bits
0x0004_0000
0x10178
Machine C mode register (MCMR)
R/W
32 bits
0x0004_0000
0x1017C
Reserved
—
48 bits
—
—
0x10184
Memory periodic timer prescaler (MPTPR)
R/W
16 bits
undefined
11.3.12/11-32
0x10188
Memory data register (MDR)
R/W
32 bits
undefined
11.3.6/11-28
0x1018C
Reserved
—
32 bits
—
—
0x10190
60x bus SDRAM mode register (PSDMR)
R/W
32 bits
0x0000_0000
11.3.3/11-20
0x10194
Local bus SDRAM mode register (LSDMR)
R/W
32 bits
0x0000_0000
11.3.4/11-24
0x10198
60x bus-assigned UPM refresh timer (PURT)
R/W
8 bits
0x00
11.3.8/11-30
0x10199
Reserved
—
24 bits
—
—
0x1019C
60x bus-assigned SDRAM refresh timer (PSRT)
R/W
8 bits
0x00
11.3.10/11-31
0x1019D
Reserved
—
24 bits
—
—
0x101A0
Local bus-assigned UPM refresh timer (LURT)
R/W
8 bits
0x00
11.3.9/11-30
0x101A1
Reserved
—
24 bits
—
—
0x101A4
Local bus-assigned SDRAM refresh timer (LSRT)
R/W
8 bits
0x00
11.3.11/11-32
0x101A5
Reserved
—
24 bits
—
—
0x101A8
Internal memory map register (IMMR)
R/W
32 bits
reset
configuration
4.3.2.7/4-36
0x101AC PCI base register 0 (PCIBR0)
R/W
32 bits
0x0000_0000
4.3.4.1 / 49
0x101B0
R/W
32 bits
0x0000_0000
4.3.4.1 / 49
—
16 bytes
—
—
PCI base register 1 (PCIBR1)
0x101B4– Reserved
0x101C3
0x101C4
PCI mask register 0 (PCIMSK0)
R/W
32 bits
0x0000_0000
4.3.4.2/4-50
0x101C8
PCI mask register 1 (PCIMSK1)
R/W
32 bits
0x0000_0000
4.3.4.2/4-50
—
52 bytes
—
—
0x101CC Reserved
–
0x101FF
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
3-4
Freescale Semiconductor
Memory Map
Table 3-1. Internal Memory Map (continued)
Address
(offset)
Register
R/W
Size
Reset
Section/Page
—
32 bytes
—
—
System Integration Timers
0x10200– Reserved
0x10 21F
0x10220
Time counter status and control register (TMCNTSC)
R/W
16 bits
0x0000
4.3.2.14/4-43
0x10224
Time counter register (TMCNT)
R/W
32 bits
0x0000_0000
4.3.2.15/4-44
0x10228
Reserved
—
32 bits
—
—
0x1022C
Time counter alarm register (TMCNTAL)
R/W
32 bits
0x0000_0000
4.3.2.16/4-45
—
16 bytes
—
—
0x10230– Reserved
0x1023F
0x10240
Periodic interrupt status and control register (PISCR)
R/W
16 bits
0x0000
4.3.3.1/4-46
0x10244
Periodic interrupt count register (PITC)
R/W
32 bits
0x0000_0000
4.3.3.2/4-47
0x10248
Periodic interrupt timer register (PITR)
R
32 bits
0x0000_0000
4.3.3.3/4-48
0x1024C– Reserved
0x102A8
—
92 bytes
—
—
0x102AA– Reserved
0x1042F
—
372
bytes
—
—
PCI
0x10430
Outbound interrupt status register (OMISR)
R/W
32 bits
0x0000_0000
9.12.3.4.3/9-80
0x10434
Outbound interrupt mask register (OMIMR)
R/W
32 bits
0x0000_0000
9.12.3.4.4/9-81
0x10440
Inbound FIFO queue port register (IFQPR)
R/W
32 bits
0x0000_0000
9.12.3.4.1/9-78
0x10444
Outbound FIFO queue port register (OFQPR)
R/W
32 bits
0x0000_0000
9.12.3.4.2/9-79
0x10450
Inbound message register 0 (IMR0)
R/W
32 bits
undefined
9.12.1.1/9-67
0x10454
Inbound message register 1 (IMR1)
R/W
32 bits
undefined
9.12.1.1/9-67
0x10458
Outbound message register 0 (OMR0)
R/W
32 bits
undefined
9.12.1.2/9-67
0x1045C
Outbound message register 1 (OMR1)
R/W
32 bits
undefined
9.12.1.2/9-67
0x10460
Outbound doorbell register (ODR)
R/W
32 bits
0x0000_0000
9.12.2.1/9-68
0x10468
Inbound doorbell register (IDR)
R/W
32 bits
0x0000_0000
9.12.2.2/9-69
0x10480
Inbound message interrupt status register (IMISR)
R/W
32 bits
0x0000_0000
9.12.3.4.5/9-82
0x10484
Inbound message interrupt mask register (IMIMR)
R/W
32 bits
0x0000_0000
9.12.3.4.6/9-83
0x104A0
Inbound free_FIFO head pointer register (IFHPR)
R/W
32 bits
0x0000_0000
9.12.3.2.1/9-72
0x104A8
Inbound free_FIFO tail pointer register (IFTPR)
R/W
32 bits
0x0000_0000
9.12.3.2.1/9-72
0x104B0
Inbound post_FIFO head pointer register (IPHPR)
R/W
32 bits
0x0000_0000
9.12.3.2.2/9-73
0x104B8
Inbound post_FIFO tail pointer register (IPTPR)
R/W
32 bits
0x0000_0000
9.12.3.2.2/9-73
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
3-5
Memory Map
Table 3-1. Internal Memory Map (continued)
Address
(offset)
Register
R/W
Size
Reset
Section/Page
0x104C0
Outbound free_FIFO head pointer register (OFHPR)
R/W
32 bits
0x0000_0000
9.12.3.3.1/9-75
0x104C8
Outbound free_FIFO tail pointer register (OFTPR)
R/W
32 bits
0x0000_0000
9.12.3.3.1/9-75
0x104D0
Outbound post_FIFO head pointer register (OPHPR)
R/W
32 bits
0x0000_0000
9.12.3.3.2/9-76
0x104D8
Outbound post_FIFO tail pointer register (OPTPR)
R/W
32 bits
0x0000_0000
9.12.3.3.2/9-76
0x104E4
Message unit control register (MUCR)
R/W
32 bits
0x0000_0002
9.12.3.4.7/9-84
0x104F0
Queue base address register (QBAR)
R/W
32 bits
0x0000_0000
9.12.3.4.8/9-85
0x10500
DMA 0 mode register (DMAMR0)
R/W
32 bits
0x0000_0000
9.13.1.6.1/9-89
0x10504
DMA 0 status register (DMASR0)
R/W
32 bits
0x0000_0000
9.13.1.6.2/9-91
0x10508
DMA 0 current descriptor address register (DMACDAR0)
R/W
32 bits
0x0000_0000
9.13.1.6.3/9-92
0x10510
DMA 0 source address register (DMASAR0)
R/W
32 bits
0x0000_0000
9.13.1.6.4/9-93
0x10518
DMA 0 destination address register (DMADAR0)
R/W
32 bits
0x0000_0000
9.13.1.6.5/9-94
0x10520
DMA 0 byte count register (DMABCR0)
R/W
32 bits
0x0000_0000
9.13.1.6.6/9-94
0x10524
DMA 0 next descriptor address register (DMANDAR0)
R/W
32 bits
0x0000_0000
9.13.1.6.7/9-95
0x10580
DMA 1 mode register (DMAMR1)
R/W
32 bits
0x0000_0000
9.13.1.6.1/9-89
0x10584
DMA 1 status register (DMASR1)
R/W
32 bits
0x0000_0000
9.13.1.6.2/9-91
0x10588
DMA 1 current descriptor address register (DMACDAR1)
R/W
32 bits
0x0000_0000
9.13.1.6.3/9-92
0x10590
DMA 1 source address register (DMASAR1)
R/W
32 bits
0x0000_0000
9.13.1.6.4/9-93
0x10598
DMA 1 destination address register (DMADAR1)
R/W
32 bits
0x0000_0000
9.13.1.6.5/9-94
0x105A0
DMA 1 byte count register (DMABCR1)
R/W
32 bits
0x0000_0000
9.13.1.6.6/9-94
0x105A4
DMA 1 next descriptor address register (DMANDAR1)
R/W
32 bits
0x0000_0000
9.13.1.6.7/9-95
0x10600
DMA 2 mode register (DMAMR2)
R/W
32 bits
0x0000_0000
9.13.1.6.1/9-89
0x10604
DMA 2 status register (DMASR2)
R/W
32 bits
0x0000_0000
9.13.1.6.2/9-91
0x10608
DMA 2 current descriptor address register (DMACDAR2)
R/W
32 bits
0x0000_0000
9.13.1.6.3/9-92
0x10610
DMA 2 source address register (DMASAR2)
R/W
32 bits
0x0000_0000
9.13.1.6.4/9-93
0x10618
DMA 2 destination address register (DAR2)
R/W
32 bits
0x0000_0000
9.13.1.6.5/9-94
0x10620
DMA 2 byte count register (DMABCR2)
R/W
32 bits
0x0000_0000
9.13.1.6.6/9-94
0x10624
DMA 2 next descriptor address register (DMANDAR2)
R/W
32 bits
0x0000_0000
9.13.1.6.7/9-95
0x10680
DMA 3 mode register (DMAMR3)
R/W
32 bits
0x0000_0000
9.13.1.6.1/9-89
0x10684
DMA 3 status register (DMASR3)
R/W
32 bits
0x0000_0000
9.13.1.6.2/9-91
0x10688
DMA 3 current descriptor address register (DMACDAR3)
R/W
32 bits
0x0000_0000
9.13.1.6.3/9-92
0x10690
DMA 3 source address register (DMASAR3)
R/W
32 bits
0x0000_0000
9.13.1.6.4/9-93
0x10698
DMA 3 destination address register (DMADAR3)
R/W
32 bits
0x0000_0000
9.13.1.6.5/9-94
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
3-6
Freescale Semiconductor
Memory Map
Table 3-1. Internal Memory Map (continued)
Address
(offset)
Register
R/W
Size
Reset
Section/Page
0x106A0
DMA 3 byte count register (DMABCR3)
R/W
32 bits
0x0000_0000
9.13.1.6.6/9-94
0x106A4
DMA 3 next descriptor address register (DMANDAR3)
R/W
32 bits
0x0000_0000
9.13.1.6.7/9-95
0x10800
PCI outbound translation address register 0 (POTAR0)
R/W
32 bits
0x0000_0000
9.11.1.3/9-30
0x10808
PCI outbound base address register 0 (POBAR0)
R/W
32 bits
0x0000_0000
9.11.1.4/9-31
0x10810
PCI outbound comparison mask register 0 (POCMR0)
R/W
32 bits
0x0000_0000
9.11.1.5/9-32
0x10818
PCI outbound translation address register 1 (POTAR1)
R/W
32 bits
0x0000_0000
9.11.1.3/9-30
0x10820
PCI outbound base address register 1 (POBAR1)
R/W
32 bits
0x0000_0000
9.11.1.4/9-31
0x10828
PCI outbound comparison mask register 1 (POCMR1)
R/W
32 bits
0x0000_0000
9.11.1.5/9-32
0x10830
PCI outbound translation address register 2 (POTAR2)
R/W
32 bits
0x0000_0000
9.11.1.3/9-30
0x10838
PCI outbound base address register 2 (POBAR2)
R/W
32 bits
0x0000_0000
9.11.1.4/9-31
0x10840
PCI outbound comparison mask register 2 (POCMR2)
R/W
32 bits
0x0000_0000
9.11.1.5/9-32
0x10878
Discard timer control register (PTCR)
R/W
32 bits
0x0000_0000
9.11.1.6/9-33
0x1087C
General purpose control register (GPCR)
R/W
32 bits
0x0000_0000
9.11.1.7/9-33
0x10880
PCI general control register (PCI_GCR)
R/W
32 bits
0x0000_0000
9.11.1.8/9-35
0x10884
Error status register (ESR)
R/W
32 bits
0x0000_0000
9.11.1.9/9-35
0x10888
Error mask register (EMR)
R/W
32 bits
0x0000_0FFF
9.11.1.10/9-37
0x1088C
Error control register (ECR)
R/W
32 bits
0x0000_00FF
9.11.1.11/9-38
0x10890
PCI error address capture register (PCI_EACR)
R/W
32 bits
0x0000_0000
9.11.1.12/9-39
0x10898
PCI error data capture register (PCI_EDCR)
R/W
32 bits
0x0000_0000
9.11.1.13/9-40
0x108A0
PCI error control capture register (PCI_ECCR)
R/W
32 bits
0x0000_0000
9.11.1.14/9-40
0x108D0
PCI inbound translation address register 1 (PITAR1)
R/W
32 bits
0x0000_0000
9.11.1.15/9-42
0x108D8
PCI inbound base address register 1 (PIBAR1)
R/W
32 bits
0x0000_0000
9.11.1.16/9-42
0x108E0
PCI inbound comparison mask register 1 (PICMR1)
R/W
32 bits
0x0000_0000
9.11.1.17/9-43
0x108E8
PCI inbound translation address register 0 (PITAR0)
R/W
32 bits
0x0000_0000
9.11.1.15/9-42
0x108F0
PCI inbound base address register 0 (PIBAR0)
R/W
32 bits
0x0000_0000
9.11.1.16/9-42
0x108F8
PCI inbound comparison mask register 0 (PICMR0)
R/W
32 bits
0x0000_0000
9.11.1.17/9-43
0x10900
PCI CFG_ADDR
R/W
32 bits
undefined
9.9.1.4.4/9-15
0x10904
PCI CFG_DATA
R/W
32 bits
0x0000_0000
9.9.1.4.4/9-15
0x10908
PCI INT_AC
R/W
32 bits
undefined
9.9.1.4.7/9-17
R/W
16 bits
0x0000
4.3.1.1/4-17
—
16 bits
—
—
Interrupt Controller
0x10C00
SIU interrupt configuration register (SICR)
0x10C02
Reserved
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
3-7
Memory Map
Table 3-1. Internal Memory Map (continued)
Address
(offset)
Register
R/W
Size
Reset
Section/Page
0x10C04
SIU interrupt vector register (SIVEC)
R/W
32 bits
0x0000_0000
4.3.1.6/4-24
0x10C08
SIU interrupt pending register (high) (SIPNR_H)
R/W
32 bits
undefined
4.3.1.4/4-21
0x10C0C SIU interrupt pending register (low) (SIPNR_L)
R/W
32 bits
0x0000_0000
4.3.1.4/4-21
0x10C10
SIU interrupt priority register (SIPRR)
R/W
32 bits
0x0530_9770
4.3.1.2/4-18
0x10C14
CPM interrupt priority register (high) (SCPRR_H)
R/W
32 bits
0x0530_9770
4.3.1.3/4-19
0x10C18
CPM interrupt priority register (low) (SCPRR_L)
R/W
32 bits
0x0530_9770
4.3.1.3/4-19
0x10C1C SIU interrupt mask register (high) (SIMR_H)
R/W
32 bits
0x0000_0000
4.3.1.5/4-22
0x10C20
SIU interrupt mask register (low) (SIMR_L)
R/W
32 bits
0x0000_0000
4.3.1.5/4-22
0x10C24
SIU external interrupt control register (SIEXR)
R/W
32 bits
0x0000_0000
4.3.1.7/4-25
—
88 bytes
—
—
0x10C28– Reserved
0x10C7F
Clocks and Reset
0x10C80
System clock control register (SCCR)
R/W
32 bits
see Table 10-2
10.4/10-6
0x10C88
System clock mode register (SCMR)
R
32 bits
see Table 10-3
10.5/10-7
0x10C90
Reset status register (RSR)
R/W
32 bits
0x0000_0003
5.2/5-4
0x10C94
Reset mode register (RMR)
R/W
32 bits
0x0000_0000
5.3/5-5
—
104
bytes
—
—
0x10C98– Reserved
0x10CFF
Input/Output Port
0x10D00
Port A data direction register (PDIRA)
R/W
32 bits
0x0000_0000
41.2.3/41-3
0x10D04
Port A pin assignment register (PPARA)
R/W
32 bits
0x0000_0000
41.2.4/41-4
0x10D08
Port A special options register (PSORA)
R/W
32 bits
0x0000_0000
41.2.5/41-4
0x10D0C Port A open drain register (PODRA)
R/W
32 bits
0x0000_0000
41.2.1/41-2
0x10D10
R/W
32 bits
0x0000_0000
41.2.2/41-2
—
12 bytes
—
—
Port A data register (PDATA)
0x10D14– Reserved
0x10D1F
0x10D20
Port B data direction register (PDIRB)
R/W
32 bits
0x0000_0000
41.2.3/41-3
0x10D24
Port B pin assignment register (PPARB)
R/W
32 bits
0x0000_0000
41.2.4/41-4
0x10D28
Port B special option register (PSORB)
R/W
32 bits
0x0000_0000
41.2.5/41-4
0x10D2C Port B open drain register (PODRB)
R/W
32 bits
0x0000_0000
41.2.1/41-2
0x10D30
R/W
32 bits
0x0000_0000
41.2.2/41-2
—
12 bytes
—
—
Port B data register (PDATB)
0x10D34– Reserved
0x10D3F
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
3-8
Freescale Semiconductor
Memory Map
Table 3-1. Internal Memory Map (continued)
Address
(offset)
Register
R/W
Size
Reset
Section/Page
0x10D40
Port C data direction register (PDIRC)
R/W
32 bits
0x0000_0000
41.2.3/41-3
0x10D44
Port C pin assignment register (PPARC)
R/W
32 bits
0x0000_0000
41.2.4/41-4
0x10D48
Port C special option register (PSORC)
R/W
32 bits
0x0000_0000
41.2.5/41-4
0x10D4C Port C open drain register (PODRC)
R/W
32 bits
0x0000_0000
41.2.1/41-2
0x10D50
R/W
32 bits
0x0000_0000
41.2.2/41-2
—
12 bytes
—
—
Port C data register (PDATC)
0x10D54– Reserved
0x10D5F
0x10D60
Port D data direction register (PDIRD)
R/W
32 bits
0x0000_0000
41.2.3/41-3
0x10D64
Port D pin assignment register (PPARD)
R/W
32 bits
0x0000_0000
41.2.4/41-4
0x10D68
Port D special option register (PSORD)
R/W
32 bits
0x0000_0000
41.2.5/41-4
0x10D6C Port D open drain register (PODRD)
R/W
32 bits
0x0000_0000
41.2.1/41-2
0x10D70
R/W
32 bits
0x0000_0000
41.2.2/41-2
R/W
8 bits
0x00
18.2.2/18-3
—
24 bits
—
—
R/W
8 bits
0x00
18.2.2/18-3
—
11 bytes
—
—
Port D data register (PDATD)
CPM Timers
0x10D80
Timer 1 and timer 2 global configuration register (TGCR1)
0x10D81
Reserved
0x10D84
Timer 3 and timer 4 global configuration register (TGCR2)
0x10D85– Reserved
0x10D8F
0x10D90
Timer 1 mode register (TMR1)
R/W
16 bits
0x0000
18.2.3/18-5
0x10D92
Timer 2 mode register (TMR2)
R/W
16 bits
0x0000
18.2.3/18-5
0x10D94
Timer 1 reference register (TRR1)
R/W
16 bits
0x0000
18.2.4/18-6
0x10D96
Timer 2 reference register (TRR2)
R/W
16 bits
0x0000
18.2.4/18-6
0x10D98
Timer 1 capture register (TCR1)
R/W
16 bits
0x0000
18.2.5/18-7
0x10D9A Timer 2 capture register (TCR2)
R/W
16 bits
0x0000
18.2.5/18-7
0x10D9C Timer 1 counter (TCN1)
R/W
16 bits
0x0000
18.2.6/18-7
0x10D9E Timer 2 counter (TCN2)
R/W
16 bits
0x0000
18.2.6/18-7
0x10DA0
Timer 3 mode register (TMR3)
R/W
16 bits
0x0000
18.2.3/18-5
0x10DA2
Timer 4 mode register (TMR4)
R/W
16 bits
0x0000
18.2.3/18-5
0x10DA4
Timer 3 reference register (TRR3)
R/W
16 bits
0x0000
18.2.4/18-6
0x10DA6
Timer 4 reference register (TRR4)
R/W
16 bits
0x0000
18.2.4/18-6
0x10DA8
Timer 3 capture register (TCR3)
R/W
16 bits
0x0000
18.2.5/18-7
0x10DAA Timer 4 capture register (TCR4)
R/W
16 bits
0x0000
18.2.5/18-7
0x10DAC Timer 3 counter (TCN3)
R/W
16 bits
0x0000
18.2.6/18-7
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
3-9
Memory Map
Table 3-1. Internal Memory Map (continued)
Address
(offset)
Register
R/W
Size
Reset
Section/Page
0x10DAE Timer 4 counter (TCN4)
R/W
16 bits
0x0000
18.2.6/18-7
0x10DB0 Timer 1 event register (TER1)
R/W
16 bits
0x0000
18.2.7/18-7
0x10DB2 Timer 2 event register (TER2)
R/W
16 bits
0x0000
18.2.7/18-7
0x10DB4 Timer 3 event register (TER3)
R/W
16 bits
0x0000
18.2.7/18-7
0x10DB6 Timer 4 event register (TER4)
R/W
16 bits
0x0000
18.2.7/18-7
—
608
bytes
—
—
R/W
8 bits
0x00
19.2.1/19-3
—
24 bits
—
—
R/W
8 bits
0x00
19.2.2/19-4
—
24 bits
—
—
R/W
8 bits
0x00
19.8.4/19-22
—
24 bits
—
—
R/W
8 bits
0x00
19.8.4/19-22
—
24 bits
—
—
R/W
8 bits
0x00
19.8.4/19-22
—
24 bits
—
—
R/W
8 bits
0x00
19.8.4/19-22
—
24 bits
—
—
R/W
8 bits
0x00
19.8.4/19-22
—
24 bits
—
—
R/W
8 bits
0x00
19.8.4/19-22
—
24 bits
—
—
R/W
8 bits
0x00
19.8.4/19-22
—
24 bits
—
—
R/W
8 bits
0x00
19.8.4/19-22
—
707
bytes
—
—
0x10DB8– Reserved
0x11017
SDMA–General
0x11018
SDMA status register (SDSR)
0x11019
Reserved
0x1101C
SDMA mask register (SDMR)
0x1101D
Reserved
IDMA
0x11020
IDMA 1 event register (IDSR1)
0x11021
Reserved
0x11024
IDMA 1 mask register (IDMR1)
0x11025
Reserved
0x11028
IDMA 2 event register (IDSR2)
0x11029
Reserved
0x1102C
IDMA 2 mask register (IDMR2)
0x1102D
Reserved
0x11030
IDMA 3 event register (IDSR3)
0x11031
Reserved
0x11034
IDMA 3 mask register (IDMR3)
0x11035
Reserved
0x11038
IDMA 4 event register (IDSR4)
0x11039
Reserved
0x1103C
IDMA 4 mask register (IDMR4)
0x1103D– Reserved
0x112FF
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
3-10
Freescale Semiconductor
Memory Map
Table 3-1. Internal Memory Map (continued)
Address
(offset)
Register
R/W
Size
Reset
Section/Page
FCC1
0x11300
FCC1 general mode register (GFMR1)
R/W
32 bits
0x0000_0000
30.2/30-3
0x11304
FCC1 protocol-specific mode register (FPSMR1)
R/W
32 bits
0x0000_0000
31.13.2/31-85
(ATM)
34.4.2.1.1/34-2
2
(IMA)
36.18.1/36-19
(Ethernet)
37.6/37-8
(HDLC)
0x11308
FCC1 transmit on demand register (FTODR1)
R/W
16 bits
0x0000
30.5/30-9
0x1130A
Reserved
—
16 bits
—
—
0x1130C
FCC1 data synchronization register (FDSR1)
R/W
16 bits
0x7E7E
30.4/30-8
0x1130E
Reserved
—
16 bits
—
—
0x11310
FCC1 event register (FCCE1)
R/W
16 bits
0x0000_0000
31.13.3/31-88
(ATM)
36.18.2/36-21
(Ethernet)
37.9/37-14
(HDLC)
0x11312
Reserved
—
16 bits
—
—
0x11314
FCC1 mask register (FCCM1)
R/W
16 bits
0x0000_0000
31.13.3/31-88
(ATM)
36.18.2/36-21
(Ethernet)
37.9/37-14
(HDLC)
0x11316
Reserved
—
16 bits
—
—
0x11318
FCC1 status register (FCCS1)
R
16 bits
0x00
37.10/37-16
(HDLC)
0x11319
Reserved
—
24 bits
—
—
0x1131C
FCC1 transmit internal rate registers for PHY0
(FTIRR1_PHY0)
R/W
8 bits
0x00
0x1131D
FCC1 transmit internal rate registers for PHY1
(FTIRR1_PHY1)
R/W
8 bits
0x00
31.15.1.4/31-93
(ATM)
34.4.2.1.2/34-2
2
(IMA)
0x1131E
FCC1 transmit internal rate registers for PHY2
(FTIRR1_PHY2)
R/W
8 bits
0x00
0x1131F
FCC1 transmit internal rate registers for PHY3
(FTIRR1_PHY3)
R/W
8 bits
0x00
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
3-11
Memory Map
Table 3-1. Internal Memory Map (continued)
Address
(offset)
Register
R/W
Size
Reset
Section/Page
FCC2
0x11320
FCC2 general mode register (GFMR2)
R/W
32 bits
0x0000_0000
30.2/30-3
0x11324
FCC2 protocol-specific mode register (FPSMR2)
R/W
32 bits
0x0000_0000
31.13.2/31-85
(ATM)
34.4.2.1.1/34-2
2
(IMA)
36.18.1/36-19
(Ethernet)
37.6/37-8
(HDLC)
0x11328
FCC2 transmit on-demand register (FTODR2)
R/W
16 bits
0x0000
30.5/30-9
0x1132A
Reserved
—
16 bits
—
—
0x1132C
FCC2 data synchronization register (FDSR2)
R/W
16 bits
0x7E7E
30.4/30-8
0x1132E
Reserved
—
16 bits
—
—
0x11330
FCC2 event register (FCCE2)
R/W
16 bits
0x0000_0000
31.13.3/31-88
(ATM)
36.18.2/36-21
(Ethernet)
37.9/37-14
(HDLC)
0x11332
Reserved
—
16 bits
—
—
0x11334
FCC2 mask register (FCCM2)
R/W
16 bits
0x0000_0000
31.13.3/31-88
(ATM)
36.18.2/36-21
(Ethernet)
37.9/37-14
(HDLC)
0x11336
Reserved
—
16 bits
—
—
0x11338
FCC2 status register (FCCS2)
R
16 bits
0x00
37.10/37-16
(HDLC)
0x11339
Reserved
—
24 bits
—
—
0x1133C
FCC2 transmit internal rate registers for PHY0
(FTIRR2_PHY0)
R/W
8 bits
0x00
0x1133D
FCC2 transmit internal rate registers for PHY1
(FTIRR2_PHY1)
R/W
8 bits
0x00
31.15.1.4/31-93
(ATM)
34.4.2.1.2/34-2
2
(IMA)
0x11133E FCC2 transmit internal rate registers for PHY2
(FTIRR2_PHY2)
R/W
8 bits
0x00
0x1133F
R/W
8 bits
0x00
FCC2 transmit internal rate registers for PHY3
(FTIRR2_PHY3)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
3-12
Freescale Semiconductor
Memory Map
Table 3-1. Internal Memory Map (continued)
Address
(offset)
Register
R/W
Size
Reset
Section/Page
FCC3
0x11340
FCC3 general mode register (GFMR3)
R/W
32 bits
0x0000_0000
30.2/30-3
0x11344
FCC3 protocol-specific mode register (FPSMR3)
R/W
32 bits
0x0000_0000
31.13.2/31-85
(ATM)
34.4.2.1.1/34-2
2
(IMA)
36.18.1/36-19
(Ethernet)
37.6/37-8
(HDLC)
0x11348
FCC3 transmit on-demand register (FTODR3)
R/W
16 bits
0x0000
30.5/30-9
0x1134A
Reserved
—
16 bits
—
—
0x1134C
FCC3 data synchronization register (FDSR3)
R/W
16 bits
0x7E7E
30.4/30-8
0x1134E
Reserved
—
16 bits
—
—
0x11350
FCC3 event register (FCCE3)
R/W
16 bits
0x0000
31.13.3/31-88
(ATM)
36.18.2/36-21
(Ethernet)
37.9/37-14
(HDLC)
0x11352
Reserved
—
16 bits
—
—
0x11354
FCC3 mask register (FCCM3)
R/W
16 bits
0x0000
31.13.3/31-88
(ATM)
36.18.2/36-21
(Ethernet)
37.9/37-14
(HDLC)
0x11356
Reserved
—
16 bits
—
—
0x11358
FCC3 status register (FCCS3)
R
16 bits
0x0000
37.10/37-16
(HDLC)
—
32 bytes
—
—
0x11359– Reserved
0x11379
FCC1 Extended Registers
0x11380
FCC1 internal rate port enable register (FIRPER1)
—
32 bit
0x0000_0000
31.15.1.4/31-93
0x11384
FCC1 internal rate event register (FIRER1)
—
32 bit
0x0000_0000
31.15.1.5/31-94
0x11388
FCC1 internal rate select register high (FIRSR1_HI)
—
32 bit
0x0000_0000
31.15.1.6/31-95
0x1138C
FCC1 internal rate select register low (FIRSR1_LO)
—
32 bit
0x0000_0000
31.15.1.6/31-95
0x11390
FCC1 general extended mode register (GFEMR1)
—
8 bit
0x00
30.2.1/30-7
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
3-13
Memory Map
Table 3-1. Internal Memory Map (continued)
Address
(offset)
Register
0x11391– Reserved
0x1139F
R/W
Size
Reset
Section/Page
—
15 bytes
—
—
FCC2 Extended Registers
0x113A0
FCC2 internal rate port enable register (FIRPER2)
R/W
32 bits
0x0000_0000
31.15.1.4/31-93
0x113A4
FCC2 internal rate event register (FIRER2)
R/W
32 bits
0x0000_0000
31.15.1.5/31-94
0x113A8
FCC2 internal rate select register high (FIRSR2_HI)
R/W
32 bits
0x0000_0000
31.15.1.6/31-95
0x113AC
FCC2 internal rate select register low (FIRSR2_LO)
R/W
32 bits
0x0000_0000
31.15.1.6/31-95
0x113B0
FCC2 general expansion mode register (GFEMR2)
R/W
8 bits
0x00
30.2.1/30-7
—
31 bytes
—
—
R/W
8 bits
0x00
30.2.1/30-7
—
47 bytes
—
—
R/W
16 bits
0x0000
35.4.1.1/35-7
R/W
16 bits
0x0000
35.4.1.2/35-8
R/W
16 bits
0x0000
35.4.1.3/35-9
R/W
16 bits
0x0000
35.4.1.4/35-10
R/W
16 bits
0x0000
35.4.1.4/35-10
R/W
16 bits
0x0000
35.4.3.6/35-12
R/W
16 bits
0x0000
35.4.3.4/35-12
R/W
16 bits
0x0000
35.4.3.5/35-12
R/W
16 bits
0x0000
35.4.3.2/35-11
R/W
16 bits
0x0000
35.4.3.3/35-12
—
12 bytes
—
—
R/W
16 bits
0x0000
35.4.1.1/35-7
R/W
16 bits
0x0000
35.4.1.2/35-8
R/W
16 bits
0x0000
35.4.1.3/35-9
R/W
16 bits
0x0000
35.4.1.4/35-10
R/W
16 bits
0x0000
35.4.1.4/35-10
R/W
16 bits
0x0000
35.4.3.6/35-12
0x113B1– Reserved
0x113CF
FCC3 Extended Registers
0x113D0
General FCC3 expansion mode register (GFEMR3)
0x113D1
Reserved
TC Layer 11
0x11400
TC1 mode register (TCMODE1)1
0x11402
TC1 cell delineation state machine register
0x11404
TC1 event register (TCER1)1
(CDSMR1)1
(TC_RCC1)1
0x11406
TC1 received cells counter
0x11408
TC1 mask register (TCMR1)1
(TC_FCC1)1
0x1140A
TC1 filtered cells counter
0x1140C
TC1 corrected cells counter (TC_CCC1)1
(TC_ICC1)1
0x1140E
TC1 idle cells counter
0x11410
TC1 transmitted cells counter (TC_TCC1)1
0x11412
TC1 error cells counter
0x11414
Reserved
(TC_ECC1)1
TC Layer 21
0x11420
TC2 mode register (TCMODE2)1
0x11422
TC2 cell delineation state machine register
0x11424
TC2 event register (TCER2)1
(TC_RCC2)1
0x11426
TC2 received cells counter
0x11428
TC2 mask register (TCMR2)1
0x1142A
TC2 filtered cells counter
(TC_FCC2)1
(CDSMR2)1
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
3-14
Freescale Semiconductor
Memory Map
Table 3-1. Internal Memory Map (continued)
Address
(offset)
Register
R/W
Size
Reset
Section/Page
0x1142C
TC2 corrected cells counter (TC_CCC2)1
R/W
16 bits
0x0000
35.4.3.4/35-12
0x1142E
TC2 idle cells counter (TC_ICC2)1
R/W
16 bits
0x0000
35.4.3.5/35-12
R/W
16 bits
0x0000
35.4.3.2/35-11
R/W
16 bits
0x0000
35.4.3.3/35-12
—
12 bytes
—
—
(TC_TCC2)1
0x11430
TC2 transmitted cells counter
0x11432
TC2 error cells counter (TC_ECC2)1
0x11434
Reserved
TC Layer 31
0x11440
TC3 mode register (TCMODE3)1
R/W
16 bits
0x0000
35.4.1.1/35-7
0x11442
TC3 cell delineation state machine register (CDSMR3)1
R/W
16 bits
0x0000
35.4.1.2/35-8
R/W
16 bits
0x0000
35.4.1.3/35-9
R/W
16 bits
0x0000
35.4.1.4/35-10
R/W
16 bits
0x0000
35.4.1.4/35-10
R/W
16 bits
0x0000
35.4.3.6/35-12
R/W
16 bits
0x0000
35.4.3.4/35-12
R/W
16 bits
0x0000
35.4.3.5/35-12
R/W
16 bits
0x0000
35.4.3.2/35-11
R/W
16 bits
0x0000
35.4.3.3/35-12
—
12 bytes
—
—
(TCER3)1
0x11444
TC3 event register
0x11446
TC3 received cells counter (TC_RCC3)1
(TCMR3)1
0x11448
TC3 mask register
0x1144A
TC3 filtered cells counter (TC_FCC3)1
(TC_CCC3)1
0x1144C
TC3 corrected cells counter
0x1144E
TC3 idle cells counter (TC_ICC3)1
(TC_TCC3)1
0x11450
TC3 transmitted cells counter
0x11452
TC3 error cells counter (TC_ECC3)1
0x11454
Reserved
TC Layer 41
0x11460
TC4 mode register (TCMODE4)1
R/W
16 bits
0x0000
35.4.1.1/35-7
0x11462
TC4 cell delineation state machine register (CDSMR4)1
R/W
16 bits
0x0000
35.4.1.2/35-8
R/W
16 bits
0x0000
35.4.1.3/35-9
R/W
16 bits
0x0000
35.4.1.4/35-10
R/W
16 bits
0x0000
35.4.1.4/35-10
R/W
16 bits
0x0000
35.4.3.6/35-12
R/W
16 bits
0x0000
35.4.3.4/35-12
R/W
16 bits
0x0000
35.4.3.5/35-12
R/W
16 bits
0x0000
35.4.3.2/35-11
R/W
16 bits
0x0000
35.4.3.3/35-12
—
12 bytes
—
—
R/W
16 bits
0x0000
35.4.1.1/35-7
(TCER4)1
0x11464
TC4 event register
0x11466
TC4 received cells counter (TC_RCC4)1
(TCMR4)1
0x11468
TC4 mask register
0x1146A
TC4 filtered cells counter (TC_FCC4)1
(TC_CCC4)1
0x1146C
TC4 corrected cells counter
0x1146E
TC4 idle cells counter (TC_ICC4)1
(TC_TCC4)1
0x11470
TC4 transmitted cells counter
0x11472
TC4 error cells counter (TC_ECC4)1
0x11474
Reserved1
TC Layer 51
0x11480
TC5 mode register (TCMODE5)1
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
3-15
Memory Map
Table 3-1. Internal Memory Map (continued)
Address
(offset)
Register
R/W
Size
Reset
Section/Page
0x11482
TC5 cell delineation state machine register (CDSMR5)1
R/W
16 bits
0x0000
35.4.1.2/35-8
0x11484
TC5 event register (TCER5)1
R/W
16 bits
0x0000
35.4.1.3/35-9
R/W
16 bits
0x0000
35.4.1.4/35-10
R/W
16 bits
0x0000
35.4.1.4/35-10
R/W
16 bits
0x0000
35.4.3.6/35-12
R/W
16 bits
0x0000
35.4.3.4/35-12
R/W
16 bits
0x0000
35.4.3.5/35-12
R/W
16 bits
0x0000
35.4.3.2/35-11
R/W
16 bits
0x0000
35.4.3.3/35-12
—
12 bytes
—
—
R/W
16 bits
0x0000
35.4.1.1/35-7
R/W
16 bits
0x0000
35.4.1.2/35-8
R/W
16 bits
0x0000
35.4.1.3/35-9
R/W
16 bits
0x0000
35.4.1.4/35-10
R/W
16 bits
0x0000
35.4.1.4/35-10
R/W
16 bits
0x0000
35.4.3.6/35-12
R/W
16 bits
0x0000
35.4.3.4/35-12
R/W
16 bits
0x0000
35.4.3.5/35-12
R/W
16 bits
0x0000
35.4.3.2/35-11
R/W
16 bits
0x0000
35.4.3.3/35-12
—
12 bytes
—
—
R/W
16 bits
0x0000
35.4.1.1/35-7
R/W
16 bits
0x0000
35.4.1.2/35-8
R/W
16 bits
0x0000
35.4.1.3/35-9
R/W
16 bits
0x0000
35.4.1.4/35-10
R/W
16 bits
0x0000
35.4.1.4/35-10
R/W
16 bits
0x0000
35.4.3.6/35-12
R/W
16 bits
0x0000
35.4.3.4/35-12
R/W
16 bits
0x0000
35.4.3.5/35-12
R/W
16 bits
0x0000
35.4.3.2/35-11
(TC_RCC5)1
0x11486
TC5 received cells counter
0x11488
TC5 mask register (TCMR5)1
(TC_FCC5)1
0x1148A
TC5 filtered cells counter
0x1148C
TC5 corrected cells counter (TC_CCC5)1
(TC_ICC5)1
0x1148E
TC5 idle cells counter
0x11490
TC5 transmitted cells counter (TC_TCC5)1
0x11492
TC5 error cells counter
0x11494
Reserved
(TC_ECC5)1
TC Layer 61
0x114A0
TC6 mode register (TCMODE6)1
0x114A2
TC6 cell delineation state machine register
0x114A4
TC6 event register (TCER6)1
(TC_RCC6)1
0x114A6
TC6 received cells counter
0x114A8
TC6 mask register (TCMR6)1
0x114AA
TC6 filtered cells counter
(CDSMR6)1
(TC_FCC6)1
0x114AC TC6 corrected cells counter (TC_CCC6)1
(TC_ICC6)1
0x114AE
TC6 idle cells counter
0x114B0
TC6 transmitted cells counter (TC_TCC6)1
0x114B2
TC6 error cells counter
0x114B4
Reserved
(TC_ECC6)1
TC Layer 71
0x114C0
TC7 mode register (TCMODE7)1
0x114C2
TC7 cell delineation state machine register
0x114C4
TC7 event register (TCER7)1
(TC_RCC7)1
0x114C6
TC7 received cells counter
0x114C8
TC7 mask register (TCMR7)1
0x114CA TC7 filtered cells counter
(TC_FCC7)1
0x114CC TC7 corrected cells counter (TC_CCC7)1
0x114CE TC7 idle cells counter
0x114D0
(TC_ICC7)1
TC7 transmitted cells counter (TC_TCC7)1
(CDSMR7)1
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
3-16
Freescale Semiconductor
Memory Map
Table 3-1. Internal Memory Map (continued)
Address
(offset)
Register
0x114D2
TC7 error cells counter (TC_ECC7)1
0x114D4
Reserved
R/W
Size
Reset
Section/Page
R/W
16 bits
0x0000
35.4.3.3/35-12
—
12 bytes
—
—
R/W
16 bits
0x0000
35.4.1.1/35-7
R/W
16 bits
0x0000
35.4.1.2/35-8
R/W
16 bits
0x0000
35.4.1.3/35-9
R/W
16 bits
0x0000
35.4.1.4/35-10
R/W
16 bits
0x0000
35.4.1.4/35-10
R/W
16 bits
0x0000
35.4.3.6/35-12
R/W
16 bits
0x0000
35.4.3.4/35-12
R/W
16 bits
0x0000
35.4.3.5/35-12
R/W
16 bits
0x0000
35.4.3.2/35-11
R/W
16 bits
0x0000
35.4.3.3/35-12
—
12 bytes
—
—
R
16 bits
0x0000
35.4.2.2/35-11
R/W
16 bits
0x0000
35.4.2.1/35-10
17.1/17-2
TC Layer 81
0x114E0
TC8 mode register (TCMODE8)1
0x114E2
TC8 cell delineation state machine register
0x114E4
TC8 event register (TCER8)1
(TC_RCC8)1
0x114E6
TC8 received cells counter
0x114E8
TC8 mask register (TCMR8)1
0x114EA
TC8 filtered cells counter
(CDSMR8)1
(TC_FCC8)1
0x114EC TC8 corrected cells counter (TC_CCC8)1
(TC_ICC8)1
0x114EE
TC8 idle cells counter
0x114F0
TC8 transmitted cells counter (TC_TCC8)1
0x114F2
TC8 error cells counter
0x114F4
Reserved
(TC_ECC8)1
TC Layer—General1
0x11500
TC general status register (TCGSR)1
0x11502
(TCGER)1
TC general event register
BRGs 5–8
0x115F0
BRG5 configuration register (BRGC5)
R/W
32 bits
0x0000_0000
0x115F4
BRG6 configuration register (BRGC6)
R/W
32 bits
0x0000_0000
0x1115F8 BRG7 configuration register (BRGC7)
R/W
32 bits
0x0000_0000
0x115FC
R/W
32 bits
0x0000_0000
—
608
bytes
—
—
R/W
8 bits
0x00
40.4.1/40-6
—
24 bits
—
—
R/W
8 bits
0x00
40.4.2/40-7
—
24 bits
—
—
R/W
8 bits
0x00
40.4.3/40-7
—
24 bits
—
—
R/W
8 bits
0x00
40.4.5/40-8
BRG8 configuration register (BRGC8)
0x11600– Reserved
0x1185F
I2C
0x11860
I2C mode register (I2MOD)
0x11861
Reserved
0x11864
I2C address register (I2ADD)
0x11865
Reserved
0x11868
I2C BRG register (I2BRG)
0x11869
Reserved
0x1186C
I2C command register (I2COM)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
3-17
Memory Map
Table 3-1. Internal Memory Map (continued)
Address
(offset)
Register
0x1186D
Reserved
0x11870
I2C event register (I2CER)
0x11871
Reserved
0x11874
I2C mask register (I2CMR)
0x11875– Reserved
0x119BF
R/W
Size
Reset
Section/Page
—
24 bits
—
—
R/W
8 bits
0x00
40.4.4/40-7
—
24 bits
—
—
R/W
8 bits
0x00
40.4.4/40-7
—
315
bytes
—
—
Communications Processor
0x119C0
Communications processor command register (CPCR)
R/W
32 bits
0x0000_0000
14.4.1/14-12
0x119C4
CP configuration register (RCCR)
R/W
32 bits
0x0000_0000
14.3.7/14-9
—
14 bytes
—
—
14.6.4/14-25
0x119C8– Reserved
0x119D5
0x119D6
CP timers event register (RTER)
R/W
16 bits
0x0000_0000
0x119DA
CP timers mask register (RTMR)
R/W
16 bits
0x0000_0000
—
16 bits
0x0000
0x119DE Reserved
R/W
16 bits
—
0x119E0
R/W
32 bits
0x0000
14.3.9/14-11
17.1/17-2
0x119DC CP time-stamp timer control register (RTSCR)
CP time-stamp register (RTSR)
14.3.8/14-10
BRGs 1–4
0x119F0
BRG1 configuration register (BRGC1)
R/W
32 bits
0x0000_0000
0x119F4
BRG2 configuration register (BRGC2)
R/W
32 bits
0x0000_0000
0x119F8
BRG3 configuration register (BRGC3)
R/W
32 bits
0x0000_0000
0x119FC
BRG4 configuration register (BRGC4)
R/W
32 bits
0x0000_0000
SCC1
0x11A00
SCC1 general mode register (GSMR_L1)
R/W
32 bits
0x0000_0000
20.1.1/20-3
0x11A04
SCC1 general mode register (GSMR_H1)
R/W
32 bits
0x0000_0000
0x11A08
SCC1 protocol-specific mode register (PSMR1)
R/W
16 bits
0x0000
20.1.2/20-9
21.16/21-13
(UART)
22.8/22-7
(HDLC)
23.11/23-10
(BISYNC)
24.9/24-8
(Transparent)
25.17/25-14
(Ethernet)
0x11A0A
Reserved
—
16 bits
—
—
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
3-18
Freescale Semiconductor
Memory Map
Table 3-1. Internal Memory Map (continued)
Address
(offset)
Register
R/W
Size
Reset
Section/Page
0x11A0C SCC1 transmit-on-demand register (TODR1)
R/W
16 bits
0x0000
20.1.4/20-10
0x11A0E
SCC1 data synchronization register (DSR1)
R/W
16 bits
0x7E7E
20.1.3/20-9
0x11A10
SCC1 event register (SCCE1)
R/W
16 bits
0x0000
0x11A14
SCC1 mask register (SCCM1)
R/W
16 bits
0x0000
21.19/21-19
(UART)
22.11/22-13
(HDLC)
23.14/23-15
(BISYNC)
24.12/24-11
(Transparent)
25.20/25-20
(Ethernet)
0x11A16
Reserved
—
8 bits
—
—
0x11A17
SCC1 status register (SCCS1)
R/W
8 bits
0x00
21.20/21-21
(UART)
22.12/22-15
(HDLC)
23.15/23-16
(BISYNC)
24.13/24-12
(Transparent)
—
8 bytes
—
—
20.1.1/20-3
0x11A18– Reserved
0x11A1F
SCC2
0x11A20
SCC2 general mode register (low) (GSMR_L2)
R/W
32 bits
0x0000_0000
0x11A24
SCC2 general mode register (high) (GSMR_H2)
R/W
32 bits
0x0000_0000
0x11A28
SCC2 protocol-specific mode register (PSMR2)
R/W
16 bits
0x0000
20.1.2/20-9
21.16/21-13
(UART)
22.8/22-7
(HDLC)
23.11/23-10
(BISYNC)
24.9/24-8
(Transparent)
25.17/25-14
(Ethernet)
0x11A2A
Reserved
—
16 bits
—
—
0x11A2C SCC2 transmit-on-demand register (TODR2)
R/W
16 bits
0x0000
20.1.4/20-10
0x11A2E
R/W
16 bits
0x7E7E
20.1.3/20-9
SCC2 data synchronization register (DSR2)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
3-19
Memory Map
Table 3-1. Internal Memory Map (continued)
Address
(offset)
Register
R/W
Size
Reset
Section/Page
21.19/21-19
(UART)
22.11/22-13
(HDLC)
23.14/23-15
(BISYNC)
24.12/24-11
(Transparent)
25.20/25-20
(Ethernet)
0x11A30
SCC2 event register (SCCE2)
R/W
16 bits
0x0000
0x11A34
SCC2 mask register (SCCM2)
R/W
16 bits
0x0000
0x11A36
Reserved
—
8 bits
—
—
0x11A37
SCC2 status register (SCCS2)
R/W
8 bits
0x00
21.20/21-21
(UART)
22.12/22-15
(HDLC)
23.15/23-16
(BISYNC)
24.13/24-12
(Transparent)
—
8 bytes
—
—
20.1.1/20-3
0x11A38– Reserved
0x11A3F
SCC3
0x11A40
SCC3 general mode register (GSMR_L3)
R/W
32 bits
0x0000_0000
0x11A44
SCC3 general mode register (GSMR_H3)
R/W
32 bits
0x0000_0000
0x11A48
SCC3 protocol-specific mode register (PSMR3)
R/W
16 bits
0x0000
20.1.2/20-9
21.16/21-13
(UART)
22.8/22-7
(HDLC)
23.11/23-10
(BISYNC)
24.9/24-8
(Transparent)
25.17/25-14
(Ethernet)
0x11A4A
Reserved
—
16 bits
—
—
0x11A4C SCC3 transmit on demand register (TODR3)
R/W
16 bits
0x0000
20.1.4/20-10
0x11A4E
R/W
16 bits
0x7E7E
20.1.3/20-9
SCC3 data synchronization register (DSR3)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
3-20
Freescale Semiconductor
Memory Map
Table 3-1. Internal Memory Map (continued)
Address
(offset)
Register
R/W
Size
Reset
Section/Page
21.19/21-19
(UART)
22.11/22-13
(HDLC)
23.14/23-15
(BISYNC)
24.12/24-11
(Transparent)
25.20/25-20
(Ethernet)
0x11A50
SCC3 event register (SCCE3)
R/W
16 bits
0x0000
0x11A54
SCC3 mask register (SCCM3)
R/W
16 bits
0x0000
0x11A56
Reserved
—
8 bits
—
—
0x11A57
SCC3 status register (SCCS3)
R/W
8 bits
0x00
21.20/21-21
(UART)
22.12/22-15
(HDLC)
23.15/23-16
(BISYNC)
24.13/24-12
(Transparent)
—
8 bytes
—
—
20.1.1/20-3
0x11A58– Reserved
0x11A5F
SCC4
0x11A60
SCC4 general mode register (GSMR_L4)
R/W
32 bits
0x0000_0000
0x11A64
SCC4 general mode register (GSMR_H4)
R/W
32 bits
0x0000_0000
0x11A68
SCC4 protocol-specific mode register (PSMR4)
R/W
16 bits
0x0000
20.1.2/20-9
21.16/21-13
(UART)
22.8/22-7
(HDLC)
23.11/23-10
(BISYNC)
24.9/24-8
(Transparent)
25.17/25-14
(Ethernet)
0x11A6A
Reserved
—
16 bits
—
—
0x11A6C SCC4 transmit on-demand register (TODR4)
R/W
16 bits
0x0000
20.1.4/20-10
0x11A6E
R/W
16 bits
0x7E7E
20.1.3/20-9
SCC4 data synchronization register (DSR4)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
3-21
Memory Map
Table 3-1. Internal Memory Map (continued)
Address
(offset)
Register
R/W
Size
Reset
Section/Page
21.19/21-19
(UART)
22.11/22-13
(HDLC)
23.14/23-15
(BISYNC)
24.12/24-11
(Transparent)
25.20/25-20
(Ethernet)
0x11A70
SCC4 event register (SCCE4)
R/W
16 bits
0x0000
0x11A74
SCC4 mask register (SCCM4)
R/W
16 bits
0x0000
0x11A77
SCC4 status register (SCCS4)
—
8 bits
0x00
21.20/21-21
(UART)
22.12/22-15
(HDLC)
23.15/23-16
(BISYNC)
24.13/24-12
(Transparent)
—
8 bytes
—
—
R/W
16 bits
0x0000
28.2.1/28-2
—
16 bits
—
—
R/W
8 bits
0x00
—
24 bits
—
R/W
8 bits
0x00
28.3.11/28-18
(UART)
28.4.10/28-28
(Transparent)
28.5.9/28-34
(GCI)
—
7 bytes
—
—
R/W
16 bits
0x0000
28.2.1/28-2
—
16 bits
—
—
R/W
8 bits
0x00
—
24 bits
—
R/W
8 bits
0x00
28.3.11/28-18
(UART)
28.4.10/28-28
(Transparent)
28.5.9/28-34
(GCI)
—
5 bytes
—
0x11A78– Reserved
0x11A7F
SMC1
0x11A82
SMC1 mode register (SMCMR1)
0x11A84
Reserved
0x11A86
SMC1 event register (SMCE1)
0x11A87
Reserved
0x11A8A
SMC1 mask register (SMCM1)
0x11A8B– Reserved
0x11A91
SMC2
0x11A92
SMC2 mode register (SMCMR2)
0x11A94
Reserved
0x11A96
SMC2 event register (SMCE2)
0x11A97
Reserved
0x11A9A
SMC2 mask register (SMCM2)
0x11A9B– Reserved
0x11A9F
—
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
3-22
Freescale Semiconductor
Memory Map
Table 3-1. Internal Memory Map (continued)
Address
(offset)
Register
R/W
Size
Reset
Section/Page
R/W
16 bits
0x0000
39.4.1/39-6
—
4 bytes
—
—
R/W
8 bits
0x00
39.4.2/39-9
—
24 bits
—
—
R/W
8 bits
0x00
39.4.2/39-9
0x11AAB Reserved
—
24 bits
—
—
0x11AAD SPI command register (SPCOM)
W
8 bits
0x00
39.4.3/39-10
0x11AAE Reserved
–
0x11AFF
—
82 bytes
—
—
SPI
0x11AA0
SPI mode register (SPMODE)
0x11AA2
Reserved
0x11AA6
SPI event register (SPIE)
0x11AA7
Reserved
0x11AAA SPI mask register (SPIM)
CPM Mux
0x11B00
CPM mux SI1 clock route register (CMXSI1CR)
R/W
8 bits
0x00
16.4.2/16-12
0x11B02
CPM mux SI2 clock route register (CMXSI2CR)
R/W
8 bits
0x00
16.4.3/16-13
0x11B03
Reserved
—
8 bits
—
—
0x11B04
CPM mux FCC clock route register (CMXFCR)
R/W
32 bits
0x0000_0000
16.4.4/16-13
0x11B08
CPM mux SCC clock route register (CMXSCR)
R/W
32 bits
0x0000_0000
16.4.5/16-16
0x11B0C CPM mux SMC clock route register (CMXSMR)
R/W
8 bits
0x00
16.4.6/16-19
—
8 bits
—
—
R/W
16 bits
0x0000
16.4.1/16-7
—
16 bytes
—
—
15.5.2/15-17
0x11B0D Reserved
0x11B0E
CPM mux UTOPIA address register
(CMXUAR)2
0x11B10– Reserved
0x11B1F
SI1 Registers
0x11B20
SI1 TDMA1 mode register (SI1AMR)
R/W
16 bits
0x0000
0x11B22
SI1 TDMB1 mode register (SI1BMR)
R/W
16 bits
0x0000
0x11B24
SI1 TDMC1 mode register (SI1CMR)
R/W
16 bits
0x0000
0x11B26
SI1 TDMD1 mode register (SI1DMR)
R/W
16 bits
0x0000
0x11B28
SI1 global mode register (SI1GMR)
R/W
8 bits
0x00
15.5.1/15-17
0x11B29
Reserved
—
8 bits
—
—
0x11B2A
SI1 command register (SI1CMDR)
R/W
8 bits
0x00
15.5.4/15-24
0x11B2B
Reserved
—
8 bits
—
—
R/W
8 bits
0x00
15.5.5/15-25
—
8 bits
—
—
0x11B2C SI1 status register (SI1STR)
0x11B2D Reserved
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
3-23
Memory Map
Table 3-1. Internal Memory Map (continued)
Address
(offset)
0x11B2E
Register
SI1 RAM shadow address register (SI1RSR)
R/W
Size
Reset
Section/Page
R/W
16 bits
0x0000
15.5.3/15-24
R/W
16 bits
0x0000
29.8.1/29-36
—
16 bits
—
R/W
16 bits
0x0000
29.8.1/29-36
—
16 bits
—
—
R/W
8 bits
0x00
29.6/29-32
—
7 bytes
—
—
15.5.2/15-17
MCC1 Registers1
0x11B30
MCC1 event register (MCCE1)1
0x11B32
Reserved
0x11B34
MCC1 mask register
0x11B36
Reserved
0x11B38
(MCCM1)1
MCC1 configuration register
(MCCF1)1
0x11B39– Reserved
0x11B3F
SI2 Registers
0x11B40
SI2 TDMA2 mode register (SI2AMR)
R/W
16 bits
0x0000
0x11B42
SI2 TDMB2 mode register (SI2BMR)
R/W
16 bits
0x0000
0x11B44
SI2 TDMC2 mode register (SI2CMR)
R/W
16 bits
0x0000
0x11B46
SI2 TDMD2 mode register (SI2DMR)
R/W
8 bits
0x0000
0x11B48
SI2 global mode register (SI2GMR)
R/W
8 bits
0x00
15.5.1/15-17
0x11B49
Reserved
—
8 bits
—
—
0x11B4A
SI2 command register (SI2CMDR)
R/W
8 bits
0x00
15.5.4/15-24
0x11B4B
Reserved
—
8 bits
—
—
R/W
8 bits
0x00
15.5.5/15-25
—
16 bits
—
—
R/W
16 bits
0x0000
15.5.3/15-24
R/W
16 bits
0x0000
29.8.1/29-36
—
16 bits
—
—
R/W
16 bits
0x0000
29.8.1/29-36
—
16 bits
—
—
R/W
8 bits
0x00
29.6/29-32
—
7 bytes
—
—
0x11B4C SI2 status register (SI2STR)
0x11B4D Reserved
0x11B4E
SI2 RAM shadow address register (SI2RSR)
MCC2 Registers
0x11B50
MCC2 event register (MCCE2)
0x11B52
Reserved
0x11B54
MCC2 mask register (MCCM2)
0x11B56
Reserved
0x11B58
MCC2 configuration register (MCCF2)
0x11B59
Reserved
USB
0x11B60
USB mode register (USMOD)
R/W
8 bits
0x00
27.5.7.1/27-17
0x11B61
USB address register (USADR)
R/W
8 bits
0x00
27.5.7.2/27-18
0x11B62
USB command register (USCOM)
R/W
8 bits
0x00
27.5.7.4/27-20
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
3-24
Freescale Semiconductor
Memory Map
Table 3-1. Internal Memory Map (continued)
Address
(offset)
Register
R/W
Size
Reset
Section/Page
0x11B64
USB end point 1 register (USEP1)
R/W
16 bits
0x0000
27.5.7.3/27-18
0x11B66
USB end point 2 register (USEP2)
R/W
16 bits
0x0000
27.5.7.3/27-18
0x11B68
USB end point 3 register (USEP3)
R/W
16 bits
0x0000
27.5.7.3/27-18
0x11B6A
USB end point 4 register (USEP4)
R/W
16 bits
0x0000
27.5.7.3/27-18
—
32 bits
—
—
R/W
16 bits
0x0000
27.5.7.5/27-20
—
16 bits
0x0000
—
0x11B6C– Reserved
0x11B6F
0x11B70
USB event register (USBER)
0x11B72
Reserved
0x11B74
USB mask register (USBMR)
R/W
16 bits
0x0000
27.5.7.6/27-21
0x11B77
USB status register (USBS)
R/W
8 bits
0x00
27.5.7.7/27-21
—
1158
bytes
—
—
R/W
512
bytes
undefined
15.4.3/15-10
—
512
bytes
—
—
R/W
512
bytes
undefined
15.4.3/15-10
—
512
bytes
—
—
R/W
512
bytes
undefined
15.4.3/15-10
—
512
bytes
—
—
R/W
512
bytes
undefined
15.4.3/15-10
0x12E00– Reserved
0x12FFF
—
512
bytes
—
—
0x13000– Reserved
0x137FF
—
2048
bytes
—
—
0x13800– Reserved
0x13FFF
—
2048
bytes
—
—
0x11B79– Reserved
0x11FFF
SI1 RAM
0x12000–
0x121FF
SI 1 transmit routing RAM (SI1TxRAM)
0x12200– Reserved
0x123FF
0x12400–
0x125FF
SI 1 receive routing RAM (SI1RxRAM)
0x12600– Reserved
0x127FF
SI2 RAM
0x12800–
0x129FF
SI 2 transmit routing RAM (SI2TxRAM)
0x12A00– Reserved
0x12BFF
0x12C00–
0x12DFF
SI 2 receive routing RAM (SI2RxRAM)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
3-25
Memory Map
Table 3-1. Internal Memory Map (continued)
Address
(offset)
Register
R/W
Size
Reset
32
Kbytes
Undefined
Section/Page
CPM Dual-Port RAM (Instruction)
0x20000– CPM Instruction RAM (IRAM)
0x27FFF
1
2
R/W
MPC8280 only. Reserved on other devices.
Reserved on the MPC8270.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
3-26
Freescale Semiconductor
Part II
Configuration and Reset
Intended Audience
Part II is intended for system designers and programmers who need to understand the operation of the
MPC8280 at start up. It assumes understanding of the PowerPC programming model described in the
previous chapters and a high level understanding of the MPC8280.
Contents
Part II describes start-up behavior of the MPC8280.
It contains the following chapters:
• Chapter 4, “System Interface Unit (SIU),” describes the system configuration and protection
functions which provide various monitors and timers, and the 60x bus configuration.
• Chapter 5, “Reset,” describes the behavior of the MPC8280 at reset and start-up.
Suggested Reading
Supporting documentation for the MPC8280 can be accessed through the world-wide web at
www.freescale.com. This documentation includes technical specifications, reference materials, and
detailed applications notes.
Conventions
This chapter uses the following notational conventions:
Bold entries in figures and tables showing registers and parameter RAM should
Bold
be initialized by the user.
mnemonics
Instruction mnemonics are shown in lowercase bold.
italics
Italics indicate variable command parameters, for example, bcctrx.
Book titles in text are set in italics.
0x0
Prefix to denote hexadecimal number
0b0
Prefix to denote binary number
rA, rB
Instruction syntax used to identify a source GPR
rD
Instruction syntax used to identify a destination GPR
REG[FIELD]
Abbreviations or acronyms for registers or buffer descriptors are shown in
uppercase text. Specific bits, fields, or numerical ranges appear in brackets. For
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
II-1
example, MSR[LE] refers to the little-endian mode enable bit in the machine state
register.
In certain contexts, such as in a signal encoding or a bit field, indicates a don’t
care.
Indicates an undefined numerical value
x
n
Acronyms and Abbreviations
Table II-1 contains acronyms and abbreviations that are used in this document. Note that the meanings for
some acronyms (such as SDR1 and DSISR) are historical, and the words for which an acronym stands may
not be intuitively obvious.
Table II-1. Acronyms and Abbreviated Terms
Term
Meaning
BIST
Built-in self test
DMA
Direct memory access
DRAM
Dynamic random access memory
EA
Effective address
GPR
General-purpose register
IEEE
Institute of Electrical and Electronics Engineers
LSB
Least-significant byte
lsb
Least-significant bit
LSU
Load/store unit
MSB
Most-significant byte
msb
Most-significant bit
MSR
Machine state register
PCI
Peripheral component interconnect
RTOS
Real-time operating system
Rx
Receive
SPR
Special-purpose register
SWT
Software watchdog timer
Tx
Transmit
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
II-2
Freescale Semiconductor
Chapter 4
System Interface Unit (SIU)
The system interface unit (SIU) consists of several functions that control system start-up and initialization,
as well as operation, protection, and the external system bus. Key features of the SIU include the
following:
• System configuration and protection
• System reset monitoring and generation
• Clock synthesizer
• Power management
• 60x bus interface
• Flexible, high-performance memory controller
• Level-two cache controller interface
• PCI interface
• IEEE 1149.1 test-access port (TAP)
Figure 4-1 is a block diagram of the SIU.
60x Bus (32-Bit Address/64-Bit Data)
G2_LE Core
Memory
Controller
Core
Configuration Registers
Counters
Bridge
Memory
Controller
Local
Interrupt
Controller
Communications
Processor
Control
Control
Local Bus (18-Bit Address/32-Bit Data)
Figure 4-1. SIU Block Diagram
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
4-1
System Interface Unit (SIU)
The system configuration and protection functions provide various monitors and timers, including the bus
monitor, software watchdog timer, periodic interrupt timer, and time counter. The clock synthesizer
generates the clock signals used by the SIU and other MPC8280 modules. The SIU clocking scheme
supports stop and normal modes.
The 60x bus interface is a standard pipelined bus. The MPC8280 allows external bus masters to request
and obtain system bus mastership. Chapter 8, “The 60x Bus,” describes bus operation, but 60x bus
configuration is explained in this section.
The memory controller module, described in Chapter 11, “Memory Controller,” provides a seamless
interface to many types of memory devices and peripherals. It supports up to twelve memory banks, each
with its own device and timing attributes. The PCI interface enables the use of standard peripherals.
The MPC8280’s implementation supports circuit board test strategies through a user- accessible test logic
that is fully compliant with the IEEE 1149.1 test access port.
4.1
System Configuration and Protection
The MPC8280 incorporates many system functions that normally must be provided in external circuits. In
addition, it is designed to provide maximum system safeguards against hardware and/or software faults.
Table 4-1 describes functions provided in the system configuration and protection submodule.
Table 4-1. System Configuration and Protection Functions
Function
Description
System
The SIU allows the user to configure the system according to the particular requirements. The functions
configuration include control of parity checking and part and mask number constants.
60x bus
monitor
Monitors the transfer acknowledge (TA) and address acknowledge (AACK) response time for all bus
accesses initiated by internal or external masters. TEA is asserted if the TA/AACK response limit is
exceeded. This function can be disabled if needed.
Local bus
monitor
Monitors transfers between local bus internal masters and local bus slaves. An internal TEA assertion
occurs if the transfer time limit is exceeded. This function can be disabled.
Software
watchdog
timer
Asserts a reset or NMI interrupt, selected by the system protection control register (SYPCR) if the
software fails to service the software watchdog timer for a certain period of time (for example, because
software is lost or trapped in a loop). After a system reset, this function is enabled, selects a maximum
time-out period, and asserts a system reset if the time-out is reached. The software watchdog timer can
be disabled or its time-out period may be changed in the SYPCR. Once the SYPCR is written, it cannot
be written again until a system reset. For more information, see Section 4.1.5, “Software Watchdog
Timer.”
Periodic
interrupt
timer (PIT)
Generates periodic interrupts for use with a real-time operating system or the application software. The
periodic interrupt timer (PIT) is clocked by the timersclk clock, providing a period from 122 µs to
8 seconds. The PIT function can be disabled if needed. See Section 4.1.4, “Periodic Interrupt Timer
(PIT).”
Time
counter
Provides a time-of-day information to the operating system/application software. It is composed of a
45-bit counter and an alarm register. A maskable interrupt is generated when the counter reaches the
value programmed in the alarm register. The time counter (TMCNT) is clocked by the timersclk clock.
See Section 4.1.3, “Time Counter (TMCNT).”
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
4-2
Freescale Semiconductor
System Interface Unit (SIU)
Figure 4-2 is a block diagram of the system configuration and protection logic.
Module
Configuration
Bus clock/8
Bus
Monitors
timersclk
Periodic Interrupt
Timer
Bus Clock
Software
Watchdog Timer
timersclk
Time
Counter
System Reset
Core’s MCP
TEA
Interrupt
System Reset
Core’s MCP
Interrupt
Figure 4-2. System Configuration and Protection Logic
Many aspects of system configuration are controlled by several SIU module configuration registers,
described in Section 4.3.2, “System Configuration and Protection Registers.”
4.1.1
Bus Monitor
The MPC8280 has two bus monitors, one for the 60x bus and one for the local bus. The bus monitor
ensures that each bus cycle is terminated within a reasonable period. The bus monitor does not count when
the bus is idle. When a transaction starts (TS asserted), the bus monitor starts counting down from the
time-out value. For standard bus transactions with an address tenure and a data tenure, the bus monitor
counts until a data beat is acknowledged on the bus. It then reloads the time-out value and resumes the
count down. This process continues until the whole data tenure is completed. Following the data tenure
the bus monitor will idle in case there is no pending transaction; otherwise it will reload the time-out value
and resume counting.
For address-only transactions, the bus monitor counts until AACK is asserted. If the monitor times out for
a standard bus transaction, transfer error acknowledge (TEA) is asserted. If the monitor times out for an
address-only transaction, the bus monitor asserts AACK and a core machine check or reset interrupt is
generated, depending on SYPCR[SWRI]. To allow variation in system peripheral response times,
SYPCR[BMT] defines the time-out period, whose maximum value can be 2,040 system bus clocks. The
timing mechanism is clocked by the system bus clock divided by eight.
4.1.2
Timers Clock
The two SIU timers (the time counter and the periodic interrupt timer) use the same clock source,
timersclk, which can be derived from several sources, as described in Figure 4-3.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
4-3
System Interface Unit (SIU)
The user should select external clock and/or BRG1 programming
to yield either 4 MHz or 32 KHz at this point.
PISCR[PTF]
PC[26]
Divide by 4
timersclk for PIT
Divide by 512
Ports Programming
CPM clock
timersclk for TMCNT
PC[27]
BRG1
PC[29]
Ports Programming
TMCNTSC[TCF]
PC[25]
Figure 4-3. Timers Clock Generation
For details, see Section 41.2.4, “Port Pin Assignment Register (PPAR).” For proper time counter
operation, the user must ensure that the frequency of timersclk for TMCNT is 8,192 Hz by properly
selecting the external clock and programming BRG1 and the prescaler control bits in the time counter
status and control register (TMCNTSC[TCF]) and periodic interrupt status and control register
(PISCR[PTF]).
4.1.3
Time Counter (TMCNT)
The time counter (TMCNT) is a 32-bit counter that is clocked by timersclk. It provides a time-of-day
indication to the operating system and application software. The counter is reset to zero on PORESET reset
or hard reset but is not effected by soft reset. It is initialized by the software; the user should set the
timersclk frequency to 8,192 Hz, as explained in Section 4.1.2, “Timers Clock.”
TMCNT can be programmed to generate a maskable interrupt when the time value matches the value in
its associated alarm register. It can also be programmed to generate an interrupt every second. The time
counter control and status register (TMCNTSC) is used to enable or disable the various timer functions
and report the interrupt source. Figure 4-4 shows a block diagram of TMCNT.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
4-4
Freescale Semiconductor
System Interface Unit (SIU)
SEC
Interrupt
timersclk for TMCNT (8,192 Hz)
Divide
by 8,192
32-Bit Counter
=
Alarm
Interrupt
32-Bit Register
Figure 4-4. TMCNT Block Diagram
Section 4.3.2.15, “Time Counter Register (TMCNT),” describes the time counter register.
4.1.4
Periodic Interrupt Timer (PIT)
The periodic interrupt timer consists of a 16-bit counter clocked by timersclk. The 16-bit counter
decrements to zero when loaded with a value from the periodic interrupt timer count register (PITC); after
the timer reaches zero, PISCR[PS] is set and an interrupt is generated if PISCR[PIE] = 1. At the next input
clock edge, the value in the PITC is loaded into the counter and the process repeats. When a new value is
loaded into the PITC, the PIT is updated, the divider is reset, and the counter begins counting.
Setting PS creates a pending interrupt that remains pending until PS is cleared. If PS is set again before
being cleared, the interrupt remains pending until PS is cleared. Any write to the PITC stops the current
countdown and the count resumes with the new value in PITC. If PTE = 0, the PIT cannot count and retains
the old count value. The PIT is not affected by reads. Figure 4-5 is a block diagram of the PIT.
PISCR[PTE]
PITC
Clock
Disable
16-Bit Modulus
Counter
timersclk
for PIT
PISCR[PS]
PIT
Interrupt
PISCR[PIE]
Figure 4-5. PIT Block Diagram
The time-out period is calculated as follows:
PIT
period
PITC + 1
PITC + 1
= ------------------------------------ = ------------------------8192
F
timersclk
This gives a range from 122 µs (PITC = 0x0000) to 8 seconds (PITC = 0xFFFF).
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
4-5
System Interface Unit (SIU)
4.1.5
Software Watchdog Timer
The SIU provides the software watchdog timer option to prevent system lock in case the software becomes
trapped in loops with no controlled exit. Watchdog timer operations are configured in the SYPCR,
described in Section 4.3.2.8, “System Protection Control Register (SYPCR).”
The software watchdog timer is enabled after reset to cause a hard reset if it times out. If the software
watchdog timer is not needed, the user must clear SYPCR[SWE] to disable it. If used, the software
watchdog timer requires a special service sequence to be executed periodically. Without this periodic
servicing, the software watchdog timer times out and issues a reset or a nonmaskable interrupt,
programmed in SYPCR[SWRI]. Once software writes SWRI, the state of SWE cannot be changed.
The software watchdog timer service sequence consists of the following two steps:
1. Write 0x556C to the software service register (SWSR)
2. Write 0xAA39 to SWSR
The service sequence clears the watchdog timer and the timing process begins again. If a value other than
0x556C or 0xAA39 is written to the SWSR, the entire sequence must start over. Although the writes must
occur in the correct order before a time-out, any number of instructions can be executed between the
writes. This allows interrupts and exceptions to occur between the two writes when necessary. Figure 4-6
shows a state diagram for the watchdog timer.
Reset
0x556C/Don’t reload
State 0
Waiting for 0x556C
State 1
Waiting for 0xAA39
0xAA39/Reload
Not 0x556C/Don’t reload
Not 0xAA39/Don’t reload
Figure 4-6. Software Watchdog Timer Service State Diagram
Although most software disciplines permit or even encourage the watchdog concept, some systems require
a selection of time-out periods. For this reason, the software watchdog timer must provide a selectable
range for the time-out period. Figure 4-7 shows how to handle this need.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
4-6
Freescale Semiconductor
System Interface Unit (SIU)
SWSR
Service
Logic
SWE
Bus
Clock
Clock
Disable
SYPCR[SWTC]
Divide By
2,048
Reload
MUX
16-Bit
SWR/Decrementer
Rollover = 0
SWP
Time-out
Reset
or MCP
Figure 4-7. Software Watchdog Timer Block Diagram
In Figure 4-7, the range is determined by SYPCR[SWTC]. The value in SWTC is then loaded into a 16-bit
decrementer clocked by the system clock. An additional divide-by-2,048 prescaler is used when needed.
The decrementer begins counting when loaded with a value from SWTC. After the timer reaches 0x0, a
software watchdog expiration request is issued to the reset or MCP control logic. Upon reset, SWTC is set
to the maximum value and is again loaded into the software watchdog register (SWR), starting the process
over. When a new value is loaded into SWTC, the software watchdog timer is not updated until the
servicing sequence is written to the SWSR. If SYPCR[SWE] is loaded with 0, the modulus counter does
not count.
4.2
Interrupt Controller
Key features of the interrupt controller include the following:
• Communications processor module (CPM) interrupt sources (FCCs, SCCs, MCCs, timers, SMCs,
TC layers, I2C, IDMA, SDMA, and SPI)
• SIU interrupt sources (PIT, TMCNT, and PCI)
• 24 external sources (16 port C and 8 IRQ)
• Programmable priority between PIT, TMCNT, and PCI
• Programmable priority between SCCs, FCCs, and MCCs
• Two priority schemes for the SCCs: grouped, spread
• Programmable highest priority request
• Unique vector number for each interrupt source
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
4-7
System Interface Unit (SIU)
4.2.1
Interrupt Configuration
Figure 4-8 shows the MPC8280 interrupt structure. The interrupt controller receives interrupts from
internal sources, such as the PIT or TMCNT, from the CPM, the PCI bridge (with its own interrupt
controller), and from external pins (port C parallel I/O pins).
Software watchdog timer
Memory controller data errors
PCI
OR
Bus monitor address only
IRQ[0–7]
IRQ0
Fall/
Level
8
IRQ5
MCP
CINT
IRQ[1–7]
16
Note
1 MPC8280 only
Edge/
Fall
Timer1
Timer2
Timer3
Timer4
FCC1
FCC2
FCC3
MCC11
MCC2
SCC1
SCC2
SCC3
USB/SCC4
SMC1
SMC2
SPI
G2_LE
Core
INT
Interrupt Controller
Port C[0–15]
PCI
TMCNT
PIT
I2C
IDMA1
IDMA2
IDMA3
IDMA4
SDMA
RISC Timers
TC layers1
Figure 4-8. MPC8280 Interrupt Structure
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
4-8
Freescale Semiconductor
System Interface Unit (SIU)
If the software watchdog timer is programmed to generate an interrupt, it always generates a machine
check interrupt to the core. The external IRQ0 can generate MCP as well. Note that the core takes the
machine check interrupt when MCP is asserted; it takes an external interrupt for any other interrupt
asserted by the interrupt controller. The core will take the critical interrupt when CINT is asserted.
The interrupt controller allows masking of each interrupt source. Multiple events within a CPM sub-block
event are also maskable.
All interrupt sources are prioritized and bits are set in the interrupt pending register (SIPNR). On the
MPC8280, the prioritization of the interrupt sources is flexible in the following two aspects:
• The relative priority of the FCCs, SCCs, and MCCs can be modified
• One interrupt source can be assigned the highest priority
When an unmasked interrupt source is pending in the SIPNR, the interrupt controller sends an interrupt
request to the core. When an exception is taken, the interrupt mask bit in the machine state register
(MSR[EE]) is cleared to disable further interrupt requests until software can handle them.
The SIU interrupt vector register (SIVEC) is updated with a 6-bit vector corresponding to the sub-block
with the highest current priority.
4.2.1.1
Machine Check Interrupt
There are several sources for a machine check interrupt (MCP):
• Software watchdog timer (when programmed to generate an interrupt—See Section 4.1.5,
“Software Watchdog Timer.”)
• IRQ0 signal (when the internal core is enabled)
• Memory controller for parity/ECC errors (see Section 10.2.6, “Machine Check Interrupt (MCP)
Generation”)
• PCI bridge
• Bus monitor time out (on an address only transaction—see Section 4.1.1, “Bus Monitor”)
When the internal core is enabled, these sources cause the interrupt controller to send a MCP to the core.
When the core is disabled the MCP assertion is reflected on IRQ0/NMI_OUT so that an external core can
serve it.
4.2.1.2
INT Interrupt
Besides the MCP sources listed above, other interrupts are taken by the core through the INT interrupt. If
the internal core is disabled, INT is reflected on IRQ7/INT_OUT so that an external core can serve it.
The interrupt controller allows masking of each interrupt source. Multiple events within a CPM sub-block
event are also maskable.
4.2.2
Interrupt Source Priorities
The interrupt controller has 37 interrupt sources that assert one interrupt request to the core. Table 4-2
shows prioritization of all interrupt sources. As described in following sections, flexibility exists in the
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
4-9
System Interface Unit (SIU)
relative ordering of the interrupts, but, in general, relative priorities are as shown. A single interrupt
priority number is associated with each table entry.
Note that the group and spread options, shown with YCC entries in Table 4-2, are described in
Section 4.2.2.1, “SCC, FCC, and MCC Relative Priority.”
Table 4-2. Interrupt Source Priority Levels
Priority Level
Interrupt Source Description
Multiple Events
1
Highest
—
2
XSIU1
No (TMCNT,PIT,PCI = Yes)
3
XSIU2 (Grouped)
No (TMCNT,PIT,PCI = Yes)
4
XSIU3 (Grouped)
No (TMCNT,PIT,PCI = Yes)
5
XSIU4 (Grouped)
No (TMCNT,PIT,PCI = Yes)
6
XCC1
Yes
7
XCC2
Yes
8
XCC3
Yes
9
XCC4
Yes
10
XSIU2 (Spread)
No (TMCNT,PIT,PCI = Yes)
11
XCC5
Yes
12
XCC6
Yes
13
XCC7
Yes
14
XCC8
Yes
15
XSIU5 (Grouped)
No (TMCNT,PIT,PCI = Yes)
16
XSIU6 (Grouped)
No (TMCNT,PIT,PCI = Yes)
17
XSIU7 (Grouped)
No (TMCNT,PIT,PCI = Yes)
18
XSIU8 (Grouped)
No (TMCNT,PIT,PCI = Yes)
19
XSIU3 (Spread)
No (TMCNT,PIT,PCI = Yes)
20
YCC1 (Grouped)
Yes
21
YCC2 (Grouped)
Yes
22
YCC3 (Grouped)
Yes
23
YCC4 (Grouped)
Yes
24
YCC5 (Grouped)
Yes
25
YCC6 (Grouped)
Yes
26
YCC7 (Grouped)
Yes
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
4-10
Freescale Semiconductor
System Interface Unit (SIU)
Table 4-2. Interrupt Source Priority Levels (continued)
Priority Level
Interrupt Source Description
Multiple Events
27
YCC8 (Grouped)
Yes
28
XSIU4 (Spread)
No (TMCNT,PIT,PCI = Yes)
29
Parallel I/O–PC15
Yes
30
Timer 1
Yes
31
Parallel I/O–PC14
Yes
32
YCC1 (Spread)
Yes
33
Parallel I/O–PC13
Yes
34
SDMA Bus Error
Yes
35
USB
Yes
36
IDMA1
Yes
37
YCC2 (Spread)
Yes
38
Parallel I/O–PC12
No
39
Parallel I/O–PC11
No
40
IDMA2
Yes
41
Timer 2
Yes
42
Parallel I/O–PC10
No
43
XSIU5 (GSIU = 1)
No (TMCNT,PIT,PCI = Yes)
44
YCC3 (Spread)
Yes
45
RISC Timer Table
Yes
46
I2C
Yes
47
YCC4 (Spread)
Yes
48
Parallel I/O–PC9
No
49
Parallel I/O–PC8
No
50
IRQ6
No
51
IDMA3
Yes
52
IRQ7
No
53
Timer 3
Yes
54
XSIU6 (GSIU = 1)
No (TMCNT,PIT,PCI = Yes)
55
YCC5 (Spread)
Yes
56
Parallel I/O–PC7
No
57
Parallel I/O–PC6
No
58
Parallel I/O–PC5
No
59
Timer 4
Yes
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
4-11
System Interface Unit (SIU)
Table 4-2. Interrupt Source Priority Levels (continued)
Priority Level
Interrupt Source Description
Multiple Events
60
YCC6 (Spread)
Yes
61
Parallel I/O–PC4
No
62
XSIU7 (GSIU = 1)
No (TMCNT,PIT,PCI = Yes)
63
IDMA4
Yes
64
SPI
Yes
65
Parallel I/O–PC3
No
66
Parallel I/O–PC2
No
67
SMC1
Yes
68
YCC7 (spread)
Yes
69
SMC2
Yes
70
Parallel I/O–PC1
No
71
Parallel I/O–PC0
No
72
XSIU8 (GSIU = 1)
No (TMCNT,PIT,PCI = Yes)
73
YCC8(spread)
Yes
74
Reserved
—
Notice the lack of SDMA interrupt sources, which are reported through each individual FCC, SCC, SMC,
SPI, or I2C channel. The only true SDMA interrupt source is the SDMA channel bus error entry that is
reported when a bus error occurs during an SDMA access. There are two ways to add flexibility to the table
of CPM interrupt priorities—the FCC, MCC, and SCC relative priority option, described in
Section 4.2.2.1, “SCC, FCC, and MCC Relative Priority,” and the highest priority option, described in
Section 4.2.2.3, “Highest Priority Interrupt.”
4.2.2.1
SCC, FCC, and MCC Relative Priority
The relative priority between the four SCCs, three FCCs, and MCC is programmable and can be changed
dynamically. In Table 4-2 there is no entry for SCC1–SCC4, MCC1–MCC2, FCC1–FCC3, but rather there
are entries for XCC1–XCC8 and YCC1–YCC8. Each SCC can be mapped to any YCC location and each
FCC and MCC can be mapped to any XCC location. The SCC, FCC, and MCC priorities are programmed
in the CPM interrupt priority registers (SCPRR_H and SCPRR_L) and can be changed dynamically to
implement a rotating priority.
In addition, the grouping of the locations of the YCC entries has the following two options
• Group. In the group scheme, all SCCs are grouped together at the top of the priority table, ahead
of most other CPM interrupt sources. This scheme is ideal for applications where all SCCs, FCCs,
and MCCs function at a very high data rate and interrupt latency is very important.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
4-12
Freescale Semiconductor
System Interface Unit (SIU)
•
Spread. In the spread scheme, priorities are spread over the table so other sources can have lower
interrupt latencies. This scheme is also programmed in the SICR but cannot be changed
dynamically.
4.2.2.2
PIT, TMCNT, PCI, and IRQ Relative Priority
The MPC8280 has seven general-purpose interrupt requests (IRQs), five of which, with the PIT, the PCI
interrupt controller, and TMCNT, can be mapped to any XSIU location. IRQ6 and IRQ7 have fixed
priority.
4.2.2.3
Highest Priority Interrupt
In addition to the FCC/MCC/SCC relative priority option, SICR[HP] can be used to specify one interrupt
source as having highest priority. This interrupt remains within the same interrupt level as the other
interrupt controller interrupts, but is serviced before any other interrupt in the table.
If the highest priority feature is not used, select the interrupt request in XSIU1 to be the highest priority
interrupt; the standard interrupt priority order is used. SICR[HP] can be updated dynamically to allow the
user to change a normally low priority source into a high priority-source for a certain period.
4.2.3
Masking Interrupt Sources
By programming the SIU mask registers, SIMR_H and SIMR_L, the user can mask interrupt requests to
the core. Each SIMR bit corresponds to an interrupt source. To enable an interrupt, set the corresponding
SIMR bit. When a masked interrupt source has a pending interrupt request, the corresponding SIPNR bit
is set, even though the interrupt is not generated to the core. The user can mask all interrupt sources to
implement a polling interrupt servicing scheme.
When an interrupt source has multiple interrupting events, the user can individually mask these events by
programming a mask register within that block. Table 4-2 shows which interrupt sources have multiple
interrupting events. Figure 4-9 shows an example of how the masking occurs, using an SCC as an example.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
4-13
System Interface Unit (SIU)
SCCE
SIPNR
Event
Bit
13 Input (or
13 Event Bits)
Request to
the core
(Other Unmasked Requests)
SCCM
SIMR
Mask
Bit
Mask
Bit
Figure 4-9. Interrupt Request Masking
4.2.4
Interrupt Vector Generation and Calculation
Pending unmasked interrupts are presented to the core in order of priority. The interrupt vector that allows
the core to locate the interrupt service routine is made available to the core by reading SIVEC. The
interrupt controller passes an interrupt vector corresponding to the highest-priority, unmasked, pending
interrupt. Table 4-3 lists encodings for the six low-order bits of the interrupt vector.
Table 4-3. Encoding the Interrupt Vector
Interrupt Number
Interrupt Source Description
Interrupt Vector
0
Error (No interrupt)
0b00_0000
1
I2C
0b00_0001
2
SPI
0b00_0010
3
RISC Timers
0b00_0011
4
SMC1
0b00_0100
5
SMC2
0b00_0101
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
4-14
Freescale Semiconductor
System Interface Unit (SIU)
Table 4-3. Encoding the Interrupt Vector (continued)
Interrupt Number
Interrupt Source Description
Interrupt Vector
6
IDMA1
0b00_0110
7
IDMA2
0b00_0111
8
IDMA3
0b00_1000
9
IDMA4
0b00_1001
10
SDMA
0b00_1010
11
USB
0b00_1011
12
Timer1
0b00_1100
13
Timer2
0b00_1101
14
Timer3
0b00_1110
15
Timer4
0b00_1111
16
TMCNT
0b01_0000
17
PIT
0b01_0001
18
PCI
0b01_0010
19
IRQ1
0b01_0011
20
IRQ2
0b01_0100
21
IRQ3
0b01_0101
22
IRQ4
0b01_0110
23
IRQ5
0b01_0111
24
IRQ6
0b01_1000
25
IRQ7
0b01_1001
26–31
Reserved
0b01_1010–01_1111
32
FCC1
0b10_0000
33
FCC2
0b10_0001
34
FCC3
0b10_0010
35
Reserved
0b10_0011
36
MCC11
0b10_0100
37
MCC2
0b10_0101
38
Reserved
0b10_0110
39
Reserved
0b10_0111
40
SCC1
0b10_1000
41
SCC2
0b10_1001
42
SCC3
0b10_1010
43
SCC4
0b10_1011
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
4-15
System Interface Unit (SIU)
Table 4-3. Encoding the Interrupt Vector (continued)
1
Interrupt Number
Interrupt Source Description
Interrupt Vector
44
TC Layer1
0b10_1100
45–47
Reserved
0b10_11xx
48
PC15
0b11_0000
49
PC14
0b11_0001
50
PC13
0b11_0010
51
PC12
0b11_0011
52
PC11
0b11_0100
53
PC10
0b11_0101
54
PC9
0b11_0110
55
PC8
0b11_0111
56
PC7
0b11_1000
57
PC6
0b11_1001
58
PC5
0b11_1010
59
PC4
0b11_1011
60
PC3
0b11_1100
61
PC2
0b11_1101
62
PC1
0b11_1110
63
PC0
0b11_1111
MPC8280 only.
Note that the interrupt vector table differs from the interrupt priority table in only two ways:
• FCC, SCC, and MCC vectors are fixed; they are not affected by the SCC group mode, spread mode,
or the relative priority order of the FCCs, SCCs, and MCC.
• An error vector exists as the last entry in Table 4-3. The error vector is issued when no interrupt is
requesting service.
4.2.4.1
Port C External Interrupts
There are 16 external interrupts, coming from the parallel I/O port C pins, PC[0–15]. When ones of these
pins is configured as an input, a change according to the SIU external interrupt control register (SIEXR)
causes an interrupt request signal to be sent to the interrupt controller. PC[0–15] lines can be programmed
to assert an interrupt request upon any change. Each port C line asserts a unique interrupt request to the
interrupt pending register and has a different internal interrupt priority level within the interrupt controller.
Requests can be masked independently in the interrupt mask register (SIMR). Notice that the global SIMR
is cleared on system reset so pins left floating do not cause false interrupts.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
4-16
Freescale Semiconductor
System Interface Unit (SIU)
4.3
Programming Model
The SIU registers are grouped into the following three categories:
• Interrupt controller registers. These registers control configuration, prioritization, and masking of
interrupts. They also include registers for determining the interrupt sources. These registers are
described in Section 4.3.1, “Interrupt Controller Registers.”
• System configuration and protection registers. These include registers for configuring the SIU,
defining the base address for the internal memory map, configuring the watchdog timer, specifying
bus characteristics, as well as general functionality of the 60x, and local buses such as arbitration,
error status, and control. These registers are described in Section 4.3.2, “System Configuration and
Protection Registers.”
• Periodic interrupt registers. These include registers for configuring and providing status for
periodic interrupts. See Section 4.3.3, “Periodic Interrupt Registers.”
4.3.1
Interrupt Controller Registers
There are seven interrupt controller registers, described in the following sections:
• Section 4.3.1.1, “SIU Interrupt Configuration Register (SICR)”
• Section 4.3.1.2, “SIU Interrupt Priority Register (SIPRR)”
• Section 4.3.1.3, “CPM Interrupt Priority Registers (SCPRR_H and SCPRR_L)”
• Section 4.3.1.4, “SIU Interrupt Pending Registers (SIPNR_H and SIPNR_L)”
• Section 4.3.1.5, “SIU Interrupt Mask Registers (SIMR_H and SIMR_L)”
• Section 4.3.1.6, “SIU Interrupt Vector Register (SIVEC)”
• Section 4.3.1.7, “SIU External Interrupt Control Register (SIEXR)”
4.3.1.1
SIU Interrupt Configuration Register (SICR)
The SIU interrupt configuration register (SICR), shown in Figure 4-10, defines the highest priority
interrupt and whether interrupts are grouped or spread in the priority table, Table 4-2.
0
Field
1
—
Reset
2
7
8
HP
13
—
14
15
GSIU SPS
0000_0000_0000_0000
R/W
R/W
Addr
0x10C00
Figure 4-10. SIU Interrupt Configuration Register (SICR)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
4-17
System Interface Unit (SIU)
The SICR register bits are described in Table 4-4.
Table 4-4. SICR Field Descriptions
Bits
Name
Description
0–1
—
Reserved, should be cleared.
2–7
HP
Highest priority. Specifies the 6-bit interrupt number of the single interrupt controller interrupt source
that is advanced to the highest priority in the table. HP can be modified dynamically. To retain the
original priority, program HP to the interrupt number assigned to XSIU1. Port C interrupts have a fixed
priority level and cannot be advanced to the highest priority level.
8–13
—
Reserved, should be cleared.
14
GSIU Group SIU. Selects the relative XSIU priority scheme. It cannot be changed dynamically.
0 Grouped. The XSIUs are grouped by priority at the top of the table.
1 Spread. The XSIUs are spread by priority in the table.
15
SPS
4.3.1.2
Spread priority scheme. Selects the relative YCC priority scheme. It cannot be changed dynamically.
0 Grouped. The YCCs are grouped by priority at the top of the table.
1 Spread. The YCCs are spread by priority in the table.
SIU Interrupt Priority Register (SIPRR)
The SIU interrupt priority register (SIPRR), shown in Figure 4-11, defines the priority between
IRQ1–IRQ5, PIT, PCI, and TMCNT.
0
2
3
5
6
8
9
11
12
15
Field
XS1P
XS2P
XS3P
XS4P
—
Reset
000
001
010
011
0000
R/W
R/W
Addr
0x10C10
16
18
19
21
22
24
25
27
28
31
Field
XS5P
XS6P
XS7P
XS8P
—
Reset
100
101
110
111
0000
R/W
R/W
Addr
0x10C12
Figure 4-11. SIU Interrupt Priority Register (SIPRR)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
4-18
Freescale Semiconductor
System Interface Unit (SIU)
The SIPRR register bits are described in Table 4-5.
Table 4-5. SIPRR Field Descriptions
Bits
Name
Description
0–2
XS1P–XSIU1
Priority order. Defines which PIT/TMCNT/PCI/IRQs asserts its request in the XSIU1 priority
position. The user should not program the same PIT/TMCNT/PCI/IRQs to more than one
priority position (1–8). These bits can be changed dynamically.
000 TMCNT asserts its request in the XSIU1 position.
001 PIT asserts its request in the XSIU1 position.
010 PCI asserts its request in the XSIU1 position.
011 IRQ1 asserts its request in the XSIU1 position.
100 IRQ2 asserts its request in the XSIU1 position.
101 IRQ3 asserts its request in the XSIU1 position.
110 IRQ4 asserts its request in the XSIU1 position.
111 IRQ5 asserts its request in the XSIU1 position.
3–11,
16–27
XS2P– XS8P
Same as XS1P, but for XSIU2–XSIU8.
12–15,
28–31
—
4.3.1.3
Reserved, should be cleared.
CPM Interrupt Priority Registers (SCPRR_H and SCPRR_L)
The CPM high interrupt priority register (SCPRR_H), shown in Figure 4-12, define priorities between the
FCCs and MCCs.
0
2
3
5
6
8
9
11
12
15
Field
XC1P
XC2P
XC3P
XC4P
—
Reset
000
001
010
011
0000
R/W
R/W
Addr
0x10C14
16
18
19
21
22
24
25
27
28
31
Field
XC5P
XC6P
XC7P
XC8P
—
Reset
100
101
110
111
0000
R/W
R/W
Addr
0x10C16
Figure 4-12. CPM High Interrupt Priority Register (SCPRR_H)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
4-19
System Interface Unit (SIU)
Table 4-6 describes SCPRR_H fields.
Table 4-6. SCPRR_H Field Descriptions
Bits
Name
0–2
XC1P–XCC1 Priority order. Defines which FCC/MCC asserts its request in the XCC1 priority position. The
user should not program the same FCC/MCC to more than one priority position (1–8). These
bits can be changed dynamically.
000 FCC1 asserts its request in the XCC1 position.
001 FCC2 asserts its request in the XCC1 position.
010 FCC3 asserts its request in the XCC1 position.
011 XCC1 position not active.
100 MCC1 asserts its request in the XCC1 position.1
101 MCC2 asserts its request in the XCC1 position.
110 XCC1 position not active.
111 XCC1 position not active.
3–11
XC2P–XC4P Same as XC1P, but for XCC2–XCC4
12–15
16–27
—
Reserved, should be cleared.
XC5P–XC8P Same as XC1P, but for XCC5–XCC8
28–31
1
Description
—
Reserved, should be cleared.
MPC8280 only.
The CPM low interrupt priority register (SCPRR_L), shown in Figure 4-13, defines prioritization of SCCs
and TC layer.
0
2
3
5
6
8
9
11
12
15
Field
YC1P
YC2P
YC3P
YC4P
—
Reset
000
001
010
011
0000
R/W
R/W
Addr
0x10C18
16
18
19
21
22
24
25
27
28
31
Field
YC5P
YC6P
YC7P
YC8P
—
Reset
100
101
110
111
0000
R/W
R/W
Addr
0x10C20
Figure 4-13. CPM Low Interrupt Priority Register (SCPRR_L)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
4-20
Freescale Semiconductor
System Interface Unit (SIU)
Table 4-7 describes SCPRR_L fields.
Table 4-7. SCPRR_L Field Descriptions
Bits
Name
Description
0–2
YC1P–YCC1 Priority order. Defines which SCC asserts its request in the YCC1 priority position. Do not
program the same SCC to multiple priority positions. This field can be changed dynamically.
000 SCC1 asserts its request in the YCC1 position.
001 SCC2 asserts its request in the YCC1 position.
010 SCC3 asserts its request in the YCC1 position.
011 SCC4 asserts its request in the YCC1 position.
100 TC layer asserts its request in the YCC1 position (MPC8280 only. Reserved on other
devices.)
1XX YCC1 position is not active.
3–11
YC2P–YC8P Same as YC1P, but for YCC2–YCC8
12–15
—
Reserved, should be cleared.
16–27 YC5P–YC8P Same as YC1P, but for YCC5–YCC8
28–31
4.3.1.4
—
Reserved, should be cleared.
SIU Interrupt Pending Registers (SIPNR_H and SIPNR_L)
Each bit in the interrupt pending registers (SIPNR_H and SIPNR_L), shown in Figure 4-14 and
Figure 4-15, corresponds to an interrupt source. When an interrupt is received, the interrupt controller sets
the corresponding SIPNR bit.
0
Field PC0
1
2
3
4
5
6
7
8
PC1
PC2
PC3
PC4
PC5
PC6
PC7
PC8
Reset
R/W
Addr
0x10C08
16
Reset
—
17
18
19
20
21
22
23
11
12
PC9 PC10 PC11 PC12
24
IRQ1 IRQ2 IRQ3 IRQ4 IRQ5 IRQ6 IRQ7
28
—
Undefined (the user should write 1s to clear these bits before using)
R/W
R/W
Addr
0x10C10
1 These
10
13
PC13
14
15
PC14 PC15
Undefined (the user should write 1s to clear these bits before using)
R/W
Field
9
29
30
31
TMCNT
PIT
PCI
01
01
01
fields are zero after reset because their corresponding mask register bits are cleared (disabled).
Figure 4-14. SIPNR_H
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
4-21
System Interface Unit (SIU)
Figure 4-15 shows SIPNR_L fields.
0
1
2
Field FCC1 FCC2 FCC3
3
—
4
5
6
7
2
MCC1 MCC2
8
—
10
11
SCC1 SCC2 SCC3 SCC4
12
TC
13
2
15
—
0000_0000_0000_00001
Reset
R/W
R/W
Addr
0x10C0C
16
Field I2C
Reset
9
17
SPI
18
19
20
21
22
23
24
25
RTT SMC1 SMC2 IDMA1 IDMA2 IDMA3 IDMA4 SDMA
26
—
27
28
29
R/W
Addr
0x10C0E
31
TIMER1 TIMER2 TIMER3 TIMER4 —
0000_0000_0000_0001
R/W
30
01
1 These
2
fields are zero after reset because their corresponding mask register bits are cleared (disabled).
MPC8280 only. Reserved on all other devices.
Figure 4-15. SIPNR_L
When a pending interrupt is handled, the user clears the corresponding SIPNR bit. However, if an event
register exists, the unmasked event register bits should be cleared instead, causing the SIPNR bit to be
cleared.
SIPNR bits are cleared by writing ones to them. Because the user can only clear bits in this register, writing
zeros to this register has no effect.
Note that the SCC/FCC/MCC SIPNR bit positions are not changed according to their relative priority.
4.3.1.5
SIU Interrupt Mask Registers (SIMR_H and SIMR_L)
Each bit in the SIU interrupt mask register (SIMR) corresponds to a interrupt source. The user masks an
interrupt by clearing and enables an interrupt by setting the corresponding SIMR bit. When a masked
interrupt occurs, the corresponding SIPNR bit is set, regardless of the SIMR bit although no interrupt
request is passed to the core.
If an interrupt source requests interrupt service when the user clears its SIMR bit, the request stops. If the
user sets the SIMR bit later, a previously pending interrupt request is processed by the core, according to
its assigned priority. The SIMR can be read by the user at any time.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
4-22
Freescale Semiconductor
System Interface Unit (SIU)
Figure 4-16 shows the SIMR_H register.
0
1
2
3
4
5
6
7
8
9
10
11
12
Field PC0 PC1 PC2 PC3 PC4 PC5 PC6 PC7 PC8 PC9 PC10 PC11 PC12
Reset
PC13
14
15
PC14 PC15
0000_0000_0000_0000
R/W
R/W
Addr
0x10C1C
16
Field
13
17
—
18
19
20
21
22
23
24
28
IRQ1 IRQ2 IRQ3 IRQ4 IRQ5 IRQ6 IRQ7
Reset
29
30
31
TMCNT
PIT
PCI
11
12
13
SCC4
TC1
27
28
—
0000_0000_0000_0000
R/W
R/W
Addr
0x10C1E
Figure 4-16. SIMR_H
Figure 4-17 shows SIMR_L.
0
1
2
Field FCC1 FCC2 FCC3
3
4
—
5
7
MCC11 MCC2
Reset
—
8
9
10
SCC1 SCC2 SCC3
15
—
0000_0000_0000_0000
R/W
R/W
Addr
0x10C20
16
Field I2C
17
SPI
18
19
20
21
22
23
24
25
RTT SMC1 SMC2 IDMA1 IDMA2 IDMA3 IDMA4 SDMA
Reset
2
6
26
—
29
30
31
TIMER1 TIMER2 TIMER3 TIMER4 —
0000_0000_0000_0000
R/W
R/W
Addr
0x10C22
MPC8280 only. Reserved on the other devices.
Figure 4-17. SIMR_L
Note the following:
• SCC/TC/MCC/FCC SIMR bit positions are not affected by their relative priority.
• The user can clear pending register bits that were set by multiple interrupt events only by clearing
all unmasked events in the corresponding event register.
• If an SIMR bit is masked at the same time that the corresponding SIPNR bit causes an interrupt
request to the core, the error vector is issued (if no other interrupts pending). Thus, the user should
always include an error vector routine, even if it contains only an rfi instruction. The error vector
cannot be masked.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
4-23
System Interface Unit (SIU)
4.3.1.6
SIU Interrupt Vector Register (SIVEC)
The SIU interrupt vector register (SIVEC), shown in Figure 4-18, contains an 8-bit code representing the
unmasked interrupt source of the highest priority level.
0
5
Field
Interrupt Code
Reset
6
7
8
9
10
11
12
13
14
15
0
0
0
0
0
0
0
0
0
0
0000_0000_0000_0000
R/W
R
Addr
0x10C04
Field
Reset
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0000_0000_0000_0000
R/W
R
Addr
0x10C06
Figure 4-18. SIU Interrupt Vector Register (SIVEC)
The SIVEC can be read as either a byte, half word, or a word. When read as a byte, a branch table can be
used in which each entry contains one instruction (branch). When read as a half word, each entry can
contain a full routine of up to 256 instructions. The interrupt code is defined such that its two lsbs are
zeroes, allowing indexing into the table, as shown in Figure 4-19.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
4-24
Freescale Semiconductor
System Interface Unit (SIU)
INTR: • • •
INTR: • • •
Save state
R3 <- @ SIVEC
R4 <-- BASE OF BRANCH TABLE
Save state
R3 <- @ SIVEC
R4 <-- BASE OF BRANCH TABLE
•••
•••
lbz
add
mtspr
bctr
RX, R3 (0) # load as byte
RX, RX, R4
CTR, RX
BASE
b
Routine1
lhz
add
mtspr
bctr
BASE
RX, R3 (0) # load as half
RX, RX, R4
CTR, RX
1st Instruction of Routine1
•
BASE + 4
b
Routine2
BASE + 400
1st Instruction of Routine2
•
BASE + 8
b
Routine3
BASE + 800
1st Instruction of Routine3
BASE + C
b
Routine4
BASE + C00
1st Instruction of Routine4
•
•
BASE +10
•
BASE +1000
•
•
BASE + n
•
BASE + n
•
•
Figure 4-19. Interrupt Table Handling Example
NOTE
The MPC8280 differs from previous MPC8xx implementations in that
when an interrupt request occurs, SIVEC can be read. If there are multiple
interrupt sources, SIVEC latches the highest priority interrupt. Note that the
value of SIVEC cannot change while it is being read.
4.3.1.7
SIU External Interrupt Control Register (SIEXR)
Each defined bit in the SIU external interrupt control register (SIEXR), shown in Figure 4-20, determines
whether the corresponding port C line asserts an interrupt request upon either a high-to-low change or any
change on the pin. External interrupts can come from port C (PC[0-15]).
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
4-25
System Interface Unit (SIU)
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Field EDPC0 EDPC1 EDPC2 EDPC3 EDPC4 EDPC5 EDPC6 EDPC7 EDPC8 EDPC9 EDPC EDPC EDPC EDPC EDPC EDPC
10
Reset
11
12
13
14
15
0000_0000_0000_0000
R/W
R/W
Addr
0x10C24
16
Field EDI0
17
18
19
20
21
22
23
EDI1
EDI2
EDI3
EDI4
EDI5
EDI6
EDI7
Reset
24
31
—
0000_0000_0000_0000
R/W
R/W
Addr
R
0x10C26
Figure 4-20. SIU External Interrupt Control Register (SIEXR)
Table 4-8 describes SIEXR fields.
Table 4-8. SIEXR Field Descriptions
Bits
Name
0–15
EDPCx
16–23
EDIx
4.3.2
Description
Edge detect mode for port Cx. The corresponding port C line (PCx) asserts an interrupt request
according to the following:
0 Any change on PCx generates an interrupt request.
1 High-to-low change on PCx generates an interrupt request.
Edge detect mode for IRQ x. The corresponding IRQ line (IRQx) asserts an interrupt request
according to the following:
0 Low assertion on IRQ x generates an interrupt request.
1 High-to-low change on IRQx generates an interrupt request.
System Configuration and Protection Registers
The system configuration and protection registers are described in the following sections.
4.3.2.1
Bus Configuration Register (BCR)
The bus configuration register (BCR), shown in Figure 4-21, contains configuration bits for various
features and wait states on the 60x bus.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
4-26
Freescale Semiconductor
System Interface Unit (SIU)
0
1
3
Field EBM
4
APD
5
L2C
7
L2D
Reset note 1
10
PLDP DREF
DAM
11
12
13
14
15
EAV ETM LETM EPAR LEPAR
R/W
16
18
NPQM
19
20
—
Reset
1
9
000_0000_0000_0000
R/W
Field
8
21
22
EXDD LPLDP
25
—
26
27
28
SPAR ISPS
0000_0000_000
note 1
R/W
R/W
Addr
0x10024
31
—
0000
Depends on reset configuration sequence. See Section 5.4.1, “Hard Reset Configuration Word.”
Figure 4-21. Bus Configuration Register (BCR)
Figure 4-9 describes BCR fields.
Table 4-9. BCR Field Descriptions
Bits
Name
Description
0
EBM
External bus mode.
0 Single MPC8280 bus mode is assumed
1 60x-compatible bus mode. For more information refer to Section 8.2, “Bus Configuration.”
1–3
APD
Address phase delay. Specifies the number of address tenure wait states for address operations
initiated by a 60x bus master. BCR[APD] specifies the number of address tenure wait states for
address operations initiated by 60x-bus devices. APD indicates how many cycles the MPC8280
should wait for ARTRY, but because it is assumed that ARTRY can be asserted (by other masters)
only on cachable address spaces, APD is considered only on transactions that hit one of the
60x-assigned memory controller banks and have the GBL signal asserted during address phase.
4
L2C
Secondary cache controller. See Chapter 12, “Secondary (L2) Cache Support.”
0 No secondary cache controller is assumed.
1 An external secondary cache controller is assumed.
5–7
L2D
L2 cache hit delay. Controls the number of clock cycles from the assertion of TS until HIT is valid.
8
PLDP
9
DREF Disable reflection. Disables reflection of system bus reflection on external pins of internal transfers
on 60x bus.
0 Enable reflection
1 Disable reflection
10
DAM
Pipeline maximum depth. See Section 8.4.5, “Pipeline Control.”
0 The pipeline maximum depth is one.
1 The pipeline maximum depth is zero.
Delay all masters. Applies to all the masters on the bus (CPU, EXT, CPM). This bit is similar to
BCR[EXDD] but with opposite polarity.
0 The memory controller inserts one wait state between the assertion of TS and the assertion of CS
when external master accesses an address space controlled by the memory controller.
1 The memory controller asserts CS on the cycle following the assertion of TS by external master
accessing an address space controlled by the memory controller.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
4-27
System Interface Unit (SIU)
Table 4-9. BCR Field Descriptions (continued)
Bits
Name
Description
11
EAV
Enable address visibility. Normally, when the MPC8280 is in single-MPC8280 bus mode, the bank
select signals for SDRAM accesses are multiplexed on the 60x bus address lines. So, for SDRAM
accesses, the internal address is not visible for debug purposes. However the bank select signals
can also be driven on dedicated pins (see SIUMCR[APPC]). In this case EAV can be used to force
address visibility.
0 Bank select signals are driven on 60x bus address lines. There is no full address visibility.
1 Bank select signals are not driven on address bus. During READ and WRITE commands to
SDRAM devices, the full address is driven on 60x bus address lines.
12
ETM
Compatibility mode enable. See Section 8.4.3.8, “Extended Transfer Mode.”
0 Strict 60x bus mode. Extended transfer mode is disabled.
1 Extended transfer mode is enabled.
13
LETM
Local bus compatibility mode enable. See Section 8.4.3.8, “Extended Transfer Mode.”
0 Extended transfer mode is disabled on the local bus.
1 Extended transfer mode is enable on the local bus.
Note that if the local bus memory controller is configured to work with read-modify-write parity, LETM
must be cleared.
14
EPAR
Even parity. Determines odd or even parity on the 60x bus.
0 Odd parity
1 Even parity
Writing the memory with EPAR = 1 and reading the memory with EPAR = 0 generates parity errors
for testing.
15
LEPAR Local bus even parity. Determines odd or even parity on the local bus.
0 Odd parity
1 Even parity
Writing the memory with LEPAR = 1 and reading the memory with LEPAR = 0 generates parity errors
for testing.
16–18 NPQM Non MPC8280 master. Identifies the type of bus masters which are connected to the arbitration lines
when the MPC8280 is in internal arbiter mode. Possible types are MPC8280 master and
non-MPC8280 master. This field is related to the data pipelining bits (BRx[DR]) in the memory
controller. Because an external bus master that is not a MPC8280 cannot use the data pipelining
feature, the MPC8280, which controls the memory, needs to know when a non-MPC8280 master is
accessing the memory and handle the transaction differently.
NPQM[0] designates the type of master connected to the set of pins BR, BG, and DBG.
NPQM[1] designates the type of master connected to the set of pins EXT_BR2, EXT_BG2, and
EXT_DBG2.
NPQM[2] designates the type of master which is connected to the set of pins EXT_BR3, EXT_BG3
and EXT_DBG3
0 The bus master connected to the arbitration lines is a MPC8280.
1 The bus master connected to the arbitration lines is not a MPC8280.
19–20
—
Reserved, should be cleared.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
4-28
Freescale Semiconductor
System Interface Unit (SIU)
Table 4-9. BCR Field Descriptions (continued)
Bits
Name
Description
21
EXDD External master delay disable. Generally, the MPC8280 adds one clock cycle delay for each external
master access to a region controlled by the memory controller. This occurs because the external
master drives the address on the external pins (compared to internal master, like the MPC8280’s
DMA, which drives the address on an internal bus in the chip). Thus, it is assumed that an additional
cycle is needed for the memory controllers banks to complete the address match. However in some
cases (when the bus is operated in low frequency), this extra cycle is not needed. The user can
disable the extra cycle by setting EXDD.
0 The memory controller inserts one wait state between the assertion of TS and the assertion of CS
when external master accesses an address space controlled by the memory controller.
1 The memory controller asserts CS on the cycle following the assertion of TS by external master
accessing an address space controlled by the memory controller.
22
LPLDP Local bus pipeline maximum depth. See Section 8.4.5, “Pipeline Control.”
0 The local bus pipeline maximum depth is one.
1 The local bus pipeline maximum depth is zero.
23–25
—
26
SPAR
Slave parity check. If set enables parity check on 60x bus transactions to the MPC8280's internal
memory space. In case of a parity error a core machine check is asserted and the error is reported
in TESCR1[ISBE,PAR] and TESCR2[REGS,DPR,PCI0,PCI1,LCL].
27
ISPS
Internal space port size. Defines the port size of MPC8280’s internal space region as seen to external
masters. Setting ISPS enables a 32-bit master to access MPC8280 internal space.
0 MPC8280 acts as a 64-bit slave to external masters accesses to its internal space.
1 MPC8280 acts as a 32-bit slave to external masters accesses to its internal space.
28–31
—
4.3.2.2
Reserved, should be cleared.
Reserved, should be cleared.
60x Bus Arbiter Configuration Register (PPC_ACR)
The 60x bus arbiter configuration register (PPC_ACR), shown in Figure 4-22, defines the arbiter modes
and parked master on the 60x bus.
0
Field
Reset
1
—
000
2
3
DBGD
EARB1
4
PRKM
See note
0010
R/W
R/W
Addr
0x10028
1
7
Depends on reset configuration sequence. See Section 5.4.1, “Hard Reset Configuration Word.”
Figure 4-22. PPC_ACR
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
4-29
System Interface Unit (SIU)
Table 4-10 describes PPC_ACR fields.
Table 4-10. PPC_ACR Field Descriptions
Bits
Name
0–1
—
2
DBGD
Data bus grant delay. Specifies the minimum number of data tenure wait states for 60x bus
master-initiated data operations. This is the minimum delay between TS and DBG.
0 DBG is asserted with TS if the data bus is free.
1 DBG is asserted one cycle after TS if the data bus is not busy.
See Section 8.5.1, “Data Bus Arbitration.”
3
EARB
External arbitration.
0 Internal arbitration is performed. See Section 8.3.1, “Arbitration Phase.”
1 External arbitration is assumed.
4–7
PRKM
Parking master.
0000 CPM high request level refers to the IDMA which involves peripherals and the following serial
channels (SCC, SPI, SMC, and I2C)
0001 CPM middle request level refers to all other serial channels (FCCs and MCCs)
0010 CPM low request level: it is possible to change the request level for all FCCs and MCCs to low
priority when PPC_ACR[4–7] = 0010 and FCRx[1] = 1 (See Section 30.7.1, “FCC Function
Code Registers (FCRx).”)
0011 PCI request level. Reserved on all other devices.
0100 Reserved
0101 Reserved
0110 Internal core
0111 External master 1
1000 External master 2
1001 External master 3
Values 1010–1111 are reserved.
4.3.2.3
Description
Reserved, should be cleared.
60x Bus Arbitration-Level Registers (PPC_ALRH/PPC_ALRL)
The 60x bus arbitration-level registers, shown in Figure 4-23 and Figure 4-24, define arbitration priority
of MPC8280 bus masters. Priority field 0 has highest-priority. For information about MPC8280 bus master
indexes, see the description of PPC_ACR[PRKM] in Table 4-10.
0
3
4
7
8
11
12
15
Field
Priority Field 0
Priority Field 1
Priority Field 2
Priority Field 3
Reset
0000
0001
0010
0110
R/W
R/W
Addr
0x1002C
16
19
20
23
24
27
28
31
Field
Priority Field 4
Priority Field 5
Priority Field 6
Priority Field 7
Reset
0011
0100
0101
0111
R/W
R/W
Addr
0x1002E
Figure 4-23. PPC_ALRH
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
4-30
Freescale Semiconductor
System Interface Unit (SIU)
PPC_ALRL, shown in Figure 4-24, defines arbitration priority of 60x bus masters 8–15. Priority field 0 is
the highest-priority arbitration level. For information about the MPC8280 bus master indexes, see the
description of PPC_ACR[PRKM] in Table 4-10.
0
3
4
7
8
11
12
15
Field
Priority Field 8
Priority Field 9
Priority Field 10
Priority Field 11
Reset
1000
1001
1010
1011
R/W
R/W
Addr
0x10030
16
19
20
23
24
27
28
31
Field
Priority Field 12
Priority Field 13
Priority Field 14
Priority Field 15
Reset
1100
1101
1110
1111
R/W
R/W
Addr
0x10032
Figure 4-24. PPC_ALRL
4.3.2.4
Local Bus Arbiter Configuration Register (LCL_ACR)
The local bus arbiter configuration register (LCL_ACR), shown in Figure 4-25, defines the arbiter modes
and the parked master on the local bus.
0
Field
1
—
2
3
DBGD
—
Reset
4
7
PRKM
0000_0010
R/W
R/W
Addr
0x10034
Figure 4-25. LCL_ACR
Table 4-11 describes LCL_ACR register bits.
Table 4-11. LCL_ACR Field Descriptions
Bits
Name
0–1
—
2
3
Description
Reserved, should be cleared.
DBGD Data bus grant delay. Specifies the minimum number of data tenure wait states for PowerPC
master-initiated data operations. This is the minimum delay between TS and DBG.
0 DBG is asserted with TS if the data bus is free.
1 DBG is asserted one cycle after TS if the data bus is not busy.
See Section 8.5.1, “Data Bus Arbitration.”
—
Reserved, should be cleared.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
4-31
System Interface Unit (SIU)
Table 4-11. LCL_ACR Field Descriptions (continued)
Bits
Name
4–7
PRKM Parking master. Defines the parked master.
0000 CPM high request level refers to the IDMA which involves peripherals and the following serial
channels (SCC, SPI, SMC, and I2C)
0001 CPM middle request level refers to all other serial channels (FCCs and MCCs)
0010 CPM low request level: it is possible to change the request level for all FCCs and MCCs to low
priority when PPC_ACR[4–7] = 0010 and FCRx[1] = 1 (See Section 28.7.1, “FCC Function
Code Registers (FCRx).”
0011 Host bridge
Values 0100–1111 are reserved.
4.3.2.5
Description
Local Bus Arbitration Level Registers (LCL_ALRH and LCL_ACRL)
The local bus arbitration level registers (LCL_ALRH and LCL_ALRL), shown in Figure 4-26 and
Figure 4-27, define arbitration priority for local bus masters 0–7. Priority field 0 has highest-priority. For
information about the MPC8280 local bus master indexes see LCL_ACR[PRKM] in Table 4-11.
0
3
4
7
8
11
12
15
Field
Priority Field 0
Priority Field 1
Priority Field 2
Priority Field 3
Reset
0000
0001
0010
0110
R/W
R/W
Addr
0x10038
16
19
20
23
24
27
28
31
Field
Priority Field 4
Priority Field 5
Priority Field 6
Priority Field 7
Reset
0011
0100
0101
0111
R/W
R/W
Addr
0x10040
Figure 4-26. LCL_ALRH
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
4-32
Freescale Semiconductor
System Interface Unit (SIU)
LCL_ALRL, shown in Figure 4-27, defines arbitration priority of MPC8280 local bus masters 8–15.
0
3
4
7
8
11
12
15
Field
Priority Field 8
Priority Field 9
Priority Field 10
Priority Field 11
Reset
1000
1001
1010
1011
R/W
R/W
Addr
0x1003C
16
19
20
23
24
27
28
31
Field
Priority Field 12
Priority Field 13
Priority Field 14
Priority Field 15
Reset
1100
1101
1110
1111
R/W
R/W
Addr
0x1003E
Figure 4-27. LCL_ALRL
4.3.2.6
SIU Module Configuration Register (SIUMCR)
The SIU module configuration register (SIUMCR), shown in Figure 4-28, contains bits that configure
various features in the SIU module.
0
1
2
3
Field
BBD
ESE
PBSE
CDIS
Reset
see
note
4
5
DPPC
6
7
L2CPC
00
R/W
Addr
0x10000
17
18
19
Field
MMR
LPBSE
—
Reset
see note
0
see note
20
21
LBPC
10
11
APPC
12
13
CS10PC
15
BCTLC
31
DBA ABA
0
14
00
22
—
0
see note
R/W
R/W
Addr
0x10002
1
9
see note
R/W
16
8
Depends on rest configuration sequence. See Section 5.4.1, “Hard Reset Configuration Word.”
Figure 4-28. SIU Model Configuration Register (SIUMCR)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
4-33
System Interface Unit (SIU)
Table 4-12 describes SIUMCR fields.
Table 4-12. SIUMCR Register Field Descriptions
Bits
Name
Description
0
BBD
Bus busy disable.
0 ABB/IRQ2 pin is ABB, DBB/IRQ3 pin is DBB
1 ABB/IRQ2 pin is IRQ2, DBB/IRQ3 pin is IRQ3
1
ESE
External snoop enable. Configures GBL/IRQ1
0 External snooping disabled. (GBL/IRQ1 pin is IRQ1)
1 External snooping enabled. (GBL/IRQ1 pin is GBL)
2
PBSE
Parity byte select enable.
0 Parity byte select is disabled. GPL4 output of UPM is available for memory control.
1 Parity byte select is enabled. GPL4 pin is used as parity byte select output from the MPC8280.
Note: Should not be set if BRx[DECC] = 00. Refer to Section 11.3.1, “Base Registers (BRx).”
3
CDIS
Core disable.
0 The MPC8280 core is enabled.
1 The MPC8280 core is disabled. MPC8280 functions as a slave device.
4–5
DPPC
Data parity pins configuration. Note that the additional arbitration lines (EXT_BR2, EXT_BG2,
EXT_DBG2, EXT_BR3, EXT_BG3, and EXT_DBG3) are operational only when ACR[EARB] = 0.
Setting EARB (to choose external arbiter) combined with programming DPPC to 11 deactivates these
lines.
DPPC
Pin
6–7
L2CPC
00
01
10
11
DP(0)/RSRV
—
DP(0)
RSRV
EXT_BR2
DP(1)/IRQ1
IRQ1
DP(1)
IRQ1
EXT_BG2
DP(2)/TLBISYNC/IRQ2
IRQ2
DP(2)
TLBISYNC
EXT_DBG2
DP(3)/IRQ3
IRQ3
DP(3)
CKSTP_OUT
EXT_BR3
DP(4)/IRQ4
IRQ4
DP(4)
CORE_SRE
SET
EXT_BG3
DP(5)/TBEN/IRQ5/CINT
IRQ5
DP(5)
TBEN
EXT_DBG3
DP(6)/CSE(0)/IRQ6
IRQ6
DP(6)
CSE(0)
IRQ6
DP(7)/CSE(1)/IRQ7
IRQ7
DP(7)
CSE(1)
IRQ7
L2 cache pins configuration.
Multiplexing
Pin
L2CPC = 00
L2CPC = 01
L2CPC = 10
CI/BADDR(29)/IRQ2
CI
IRQ2
BADDR(29)
WT/BADDR(30)/IRQ3
WT
IRQ3
BADDR(30)
L2_HIT/IRQ4
L2_HIT
IRQ4
—
CPU_BG/BADDR(31)/IRQ5/CINT
CPU_BG
IRQ5
BADDR(31)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
4-34
Freescale Semiconductor
System Interface Unit (SIU)
Table 4-12. SIUMCR Register Field Descriptions (continued)
Bits
Name
Description
8–9
LBPC
Local bus pins configuration.
Note: LBPC should be programmed only during the hard reset configuration sequence (using the hard
reset configuration word).
00 Local bus pins function as local bus
01 Local bus pins function as PCI bus. Reserved on all other devices.
10 Local bus pins function as core pins
11 Reserved
10–11
APPC
Address parity pins configuration. Note that during power on reset the MODCK pins are used for PLL
configuration. The pin multiplexing indicated in the table applies only to normal operation. Selection
between IRQ7 and INT_OUT is according to CPU state. If the core is disabled, the pin is INT_OUT;
otherwise it is IRQ7.
APPC
Pin
12–13
00
01
10
11
MODCK1/AP(1)/TC(0)/
BNKSEL(0)
TC(0)
AP(1)
BNKSEL(0)
—
MODCK2/AP(2)/TC(1)/
BNKSEL(1)
TC(1)
AP(2)
BNKSEL(1)
MODCK3/AP(3)/TC(2)/
BNKSEL(2)
TC(2)
AP(3)
BNKSEL(2)
IRQ7/INT_OUT/APE
IRQ7/
INT_OUT
APE
IRQ7/
INT_OUT
IRQ7/
INT_OUT
CS11/AP(0)
CS11
AP(0)
CS11
—
CS10PC Chip select 10-pin configuration.
CS10PC
Pin
CS10/BCTL1
14–15
BCTLC
MMR
01
10
CS10
BCTL1
—
Configuration for the control lines for external buffers.
00
01
10
11
16-17
00
BCTL0 is used as W/R control for external buffers. BCTL1 is used as OE control for external buffers.
BCTL0 is used as W/R control for external buffers. BCTL1 is used as OE control for external buffers.
BCTL0 is used as WE control for external buffers. BCTL1 is used as RE control for external buffers.
Reserved
Mask masters requests. In some systems, several bus masters are active during normal operation; only
one should be active during boot sequence. The active master, which is the boot device, initializes
system memories and devices and enables all other masters. MMR facilitates such a boot scheme by
masking the selected master’s bus requests. MMR can be configured through the hard reset
configuration sequence (see Section 5.4.2, “Hard Reset Configuration Examples”). Typically system
configuration identifies only one master is the boot device, which initializes the system and then
enables all other devices by writing 00 to MMR.
Note: It is not recommended to mask the request of a master which is defined as the parked master in
the arbiter, since this cannot prevent this master from getting a bus grant.
00 No masking on bus request lines.
01 Reserved
10 The MPC8280’s internal core bus request masked and external bus requests two and three masked
(boot master connected to external bus request 1).
11 All external bus requests masked (boot master is the MPC8280’s internal core).
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
4-35
System Interface Unit (SIU)
Table 4-12. SIUMCR Register Field Descriptions (continued)
Bits
Name
18
LPBSE
19
—
20
DBA
Data output buffer impedance configuration. The pins in this group include D[0-63] and
PWE[0-7]/PSDDQM[0-7]/PBS[0-7].
0 The output buffer typical impedance is 45 Ω.
1 The output buffer typical impedance is 25 Ω.
21
ABA
Address output buffer impedance configuration. The pins in this group include A[0-31],
PSDA10/PGPL0, PSDWE/PGPL1, POE/PSDRAS/PGPL2, PSDCAS/PGPL3, PGTA/PUPM,
WAIT/PGPl4, PSDAMUX/PGPL5 and BNKSEL[0:2].
0 The output buffer typical impedance is 45 Ω.
1 The output buffer typical impedance is 25 Ω.
22–31
—
4.3.2.7
Description
Local bus parity byte select enable.
0 Parity byte select is disabled. LGPL4 output of UPM is available for memory control.
1 Parity byte select is enabled. LGPL4 pin is used as local bus parity byte select output from the
MPC8280.
Reserved, should be cleared.
Reserved, should be cleared.
Internal Memory Map Register (IMMR)
The internal memory map register (IMMR), shown in Figure 4-29, contains identification of a specific
device as well as the base address for the internal memory map. Software can deduce availability and
location of any on-chip system resources from the values in IMMR. PARTNUM and MASKNUM are
mask programmed and cannot be changed for any particular device.
0
13
Field
ISB
Reset
14
15
—
Depends on reset configuration sequence. See Section 5.4.1, “Hard Reset Configuration Word.”
R/W
R/W
Addr
0x101A8
16
23
24
31
Field
PARTNUM
MASKNUM
Reset
0000_1010
0000_0000
R/W
R
Addr
0x101AA
Figure 4-29. Internal Memory Map Register (IMMR)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
4-36
Freescale Semiconductor
System Interface Unit (SIU)
Table 4-13 describes IMMR fields.
Table 4-13. IMMR Field Descriptions
Bits
Name
Description
0–13
ISB
Internal space base. Defines the base address of the internal memory space. The value of ISB
be configured at reset to one of 8 addresses; it can then be changed to any value by the
software. The default is 0, which maps to address 0x0000_0000.
ISB defines the 14 msbs of the memory map register base address. IMMR itself is mapped in the
internal memory space region. As soon as the ISB is written with a new base address, the IMMR
base address is relocated according to the ISB. ISB can be configured to one of 8 possible
addresses at reset to enable the configuration of multiple-MPC8280 systems.
The number of programmable bits in this field, and hence the resolution of the location of
internal space, depends on the internal memory space of a specific implementation. In the
MPC8280, all 14 bits can be programmed. See Chapter 3, “Memory Map,” for details on the
device’s internal memory map and Chapter 5, “Reset,” for the available default initial values.
14–15
—
Reserved, should be cleared.
16–23
PARTNUM
Part number. This read-only field is mask-programmed with a code corresponding to the part
number of the part on which the SIU is located. It is intended to help factory test and user code
which is sensitive to part changes. This changes when the part number changes. For example,
it would change if any new module is added or if the size of any memory module is changed. It
would not change if the part is changed to fix a bug in an existing module. The part number for
the MPC8280 is 0x0A.
24–31 MASKNUM Mask number. This read-only field is mask-programmed with a code corresponding to the mask
number of the part on which the SIU is located. It is intended to help factory test and user code
which is sensitive to part changes. It is programmed in a commonly changed layer and should
be changed for all mask set changes. The first revision of the MPC8280 has 0x00 in this field.
The value of this field is changed every revision of the device.
4.3.2.8
System Protection Control Register (SYPCR)
The system protection control register, shown in Figure 4-30, controls the system monitors, software
watchdog period, and bus monitor timing. SYPCR can be read at any time but can be written only once
after system reset.
0
15
Field
SWTC
Reset
1111_1111_1111_1111
R/W
R/W
Addr
0x10004
16
23
Field
BMT
Reset
1111_1111
24
25
PBME LBME
0
R/W
R/W
Addr
0x10006
0
26
28
—
00_0
29
30
31
SWE SWRI SWP
1
1
1
Figure 4-30. System Protection Control Register (SYPCR)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
4-37
System Interface Unit (SIU)
Table 4-14 describes SYPCR fields.
Table 4-14. SYPCR Field Descriptions
Bits
Name
Description
0–15
SWTC Software watchdog timer count. Contains the count value for the software watchdog timer.
16–23
BMT
24
PBME
60x bus monitor enable.
0 60x bus monitor is disabled.
1 The 60x bus monitor is enabled.
25
LBME
Local bus monitor enable.
0 Local bus monitor is disabled.
1 The local bus monitor is enabled.
26–28
—
29
SWE
Software watchdog enable. Enables the operation of the software watchdog timer. It should be
cleared by software after a system reset to disable the software watchdog timer.
30
SWRI
Software watchdog reset/interrupt select.
0 Software watchdog timer and bus monitor time-out cause a machine check interrupt to the core.
1 Software watchdog timer and bus monitor time-out cause a hard reset (this is the default value
after soft reset).
31
SWP
Software watchdog prescale. Controls the divide-by-2,048 software watchdog timer prescaler.
0 The software watchdog timer is not prescaled.
1 The software watchdog timer clock is prescaled.
4.3.2.9
Bus monitor timing. Defines the time-out period for the bus monitor, the granularity of this field is 8
bus clocks. (BMT = 0xFF is translated to 0x7f8 clock cycles). BMT is used both in the 60x and local
bus monitors.
Note that the value 0 in invalid; an error is generated for each bus transaction.
Reserved, should be cleared.
Software Service Register (SWSR)
The software service register (SWSR) is the location to which the software watchdog timer servicing
sequence is written. To prevent software watchdog timer time-out, the user should write 0x556C followed
by 0xAA39 to this register, which resides at 0x1000E. SWSR can be written at any time, but returns all
zeros when read.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
4-38
Freescale Semiconductor
System Interface Unit (SIU)
4.3.2.10
60x Bus Transfer Error Status and Control Register 1 (TESCR1)
The 60x bus transfer error status and control register 1 (TESCR1) is shown in Figure 4-31.
0
Field
BM
1
2
ISBE PAR
3
ECC2
4
5
ECC1 WP
Reset
6
7
EXT
9
TC
10
11
—
15
TT
0000_0000_0000_0000
R/W
R/W
Addr
0x10040
Field
16
17
18
—
DMD
—
19
20
21
22
23
24
PCIMCP DER IRQ0 SWD ADO
Reset
31
ECNT
0000_0000_0000_0000
R/W
R/W
Addr
0x10042
Note: Bits 0–15 and 19–23 are status bits and are cleared by writing 1s.
Figure 4-31. 60x Bus Transfer Error Status and Control Register 1 (TESCR1)
Table 4-15 describes TESCR1 fields.
Table 4-15. TESCR1 Field Descriptions
Bits
Name
0
BM
1
ISBE
Description
60x bus monitor time-out. Set when TEA is asserted due to the 60x bus monitor time-out.
Internal space bus error. Indicates that one of the following occurred:
• TEA was asserted due to an error on a transaction to MPC8280’s internal memory space
• An MCP was caused by a parity error on a transaction to MPC8280’s internal memory space. Possible
only if BCR[SPAR] = 1.
TESCR2[REGS,DPR, LCL, PCI0, PCI1] indicate which of MPC8280’s internal slaves caused the error.
2
PAR
60x bus parity error. Indicates that an MCP was caused due to one of the following:
• Parity error on 60x bus access controlled by the memory controller. TESCR2[PB] indicates which byte
lane caused the error; TESCR2[BNK] indicates which memory controller bank was accessed.
• Parity error on a transaction to MPC8280’s internal memory space. Possible only if BCR[SPAR] = 1.
3
ECC2
Double ECC error. Indicates that MCP was asserted due to double ECC error on the 60x bus.
TESCR2[BNK] indicates which memory controller bank was accessed.
4
ECC1
Single ECC error. Indicates that MCP was asserted due to single bit ECC error on the 60x bus.
TESCR2[BNK] indicates which memory controller bank was accessed. Single-bit errors are fixed by the
ECC logic. However, if the ECC counter (ECNT) has reached its maximum value, all single-bit errors
cause the assertion of MCP.
5
WP
Write protect error. Indicates that a write was attempted to a 60x bus memory region that was defined as
read-only in the memory controller. Note that this alone does not cause TEA assertion. Usually, in this
case, the bus monitor will time-out.
6
EXT
External error. Indicates that TEA was asserted by an external bus slave.
7–9
TC
Transfer code. Indicates the transfer code of the 60x bus transaction that caused the TEA or MCP. See
Section 8.4.3.2, “Transfer Code Signals TC[0–2],” for a description of the various transfer codes.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
4-39
System Interface Unit (SIU)
Table 4-15. TESCR1 Field Descriptions (continued)
Bits
Name
10
—
Reserved, should be cleared.
11–15
TT
Transfer type. These bits indicates the transfer type of the 60x bus transaction that caused the TEA or
MCP. See Section 8.4.3.1, “Transfer Type Signal (TT[0–4]) Encoding,” for a description of the various
transfer types.
16
—
Reserved, should be cleared.
17
DMD
18
—
19
Description
Data errors disable.
0 Errors are enabled.
1 All data errors (parity and single and double ECC errors) on the 60x bus are disabled.
Reserved, should be cleared.
PCIMCP PCI machine check. Set when a core machine check is asserted from the PCI bridge.
20
DER
.Data error. Set when a core machine check is asserted due to ECC or parity errors.
21
IRQ0
External machine check. Set when a machine check is asserted due to the external machine check pin
(IRQ0).
22
SWD
Software watchdog time-out. Indicates that a core machine check was asserted due to a time-out in the
software watchdog. See Section 4.1.5, “Software Watchdog Timer.”
23
ADO
60x bus monitor address-only time-out. Set when a core machine check is asserted due to time-out of the
bus monitor in an address only transaction. See Section 4.1.1, “Bus Monitor.”
24–31
ECNT
Single ECC error counter. Indicates the number of single ECC errors that occurred in the system. When
the counter reaches its maximum value (255), MCP is asserted for all single ECC errors. This feature
gives the system the ability to withstand a few random errors yet react to a catastrophic failure. The user
can set a lower threshold to the number of tolerated single ECC errors by writing some value to ECNT.
The counter starts from this value instead of zero.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
4-40
Freescale Semiconductor
System Interface Unit (SIU)
4.3.2.11
60x Bus Transfer Error Status and Control Register 2 (TESCR2)
The 60x bus transfer error status and control register 2 (TESCR2) is shown in Figure 4-32.
0
Field
1
—
2
REGS DPR
3
4
5
6
7
—
PCI0
PCI1
—
LCL
Reset
8
15
PB
0000_0000_0000_0000
R/W
R/W
Addr
0x10044
16
27
Field
BNK
Reset
28
31
—
0000_0000_0000_0000
R/W
R/W
Addr
0x10046
Note: all bits are status bits and are cleared by writing 1s.
Figure 4-32. 60x Bus Transfer Error Status and Control Register 2 (TESCR2)
The TESCR2 register is described in Table 4-16.
Table 4-16. TESCR2 Field Descriptions
Bits
Name
0
—
1
Description
Reserved, should be cleared.
REGS Internal registers error. An error occurred in a transaction to the MPC8280’s internal registers.
2
DPR
Dual port ram error. An error occurred in a transaction to the MPC8280’s dual-port RAM.
3
—
4
PCI0
PCI memory space 0 error. An error occurred in a transaction to the PCI memory space configured
by PCIBR0 and PCIMSK0.
5
PCI1
PCI memory space 1 error. An error occurred in a transaction to the PCI memory space configured
by PCIBR1 and PCIMSK1.
6
—
7
LCL
Local bus bridge error. An error occurred in a transaction to the MPC8280’s 60x bus to local bus
bridge.
8–15
PB
Parity error on byte. There are eight parity error status bits, one per 8-bit lane. A bit is set for the
byte that had a parity error.
16–27
BNK
28–31
—
Reserved, should be cleared.
Reserved, should be cleared.
Memory controller bank. There are twelve error status bits, one per memory controller bank. A bit
is set for the 60x bus memory controller bank that had an error. Note that this field is invalid if the
error was not caused by ECC or parity checks.
Reserved, should be cleared.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
4-41
System Interface Unit (SIU)
4.3.2.12
Local Bus Transfer Error Status and Control Register 1 (L_TESCR1)
The local bus transfer error status and control register 1 (L_TESCR1) is shown in Figure 4-33.
0
Field BM
1
2
—
PAR
3
4
—
5
6
WP
—
Reset
7
9
TC
11
—
15
TT
0000_0000_0000_0000
R/W
R/W
Addr
0x10048
Field
10
16
17
18
—
DMD
19
—
20
21
31
DER
Reset
—
0000_0000_0000_0000
R/W
R/W
Addr
0x1004A
Note: Bits 0–15 and 19–23 are status bits and are cleared by writing 1s.
Figure 4-33. Local Bus Transfer Error Status and Control Register 1 (L_TESCR1)
The L_TESCR1 register bits are described in Table 4-17.
Table 4-17. L_TESCR1 Field Descriptions
Bits
Name
Description
0
BM
Bus monitor time-out. Indicates that TEA was asserted due to the local bus monitor time-out.
1
—
Reserved, should be cleared.
2
PAR
3–4
—
5
WP
6
—
Reserved, should be cleared.
7–9
TC
Transfer code. Indicates the transfer code of the local bus transaction that caused the TEA.
000 60x-local bridge
001 Reserved
010 Local DMA function code 0
011 Local DMA function code 1
1xx Reserved
10
—
Reserved, should be cleared.
11–15
TT
Transfer type. Indicates the transfer type of the local bus transaction that caused the TEA.
Section 8.4.3.1, “Transfer Type Signal (TT[0–4]) Encoding,” describes the various transfer types.
16
—
Reserved, should be cleared.
17
DMD
Parity error. Indicates that MCP was asserted due to parity error on the local bus. L_TESCR2[PB]
indicates the byte lane that caused the error and L_TESCR2[BNK] indicates which memory
controller bank was accessed.
Reserved, should be cleared.
Write protect error. Indicates that a write was attempted to a local bus memory region that was
defined as read-only in the memory controller. Note that this alone does not cause TEA assertion.
Usually, in this case, the bus monitor will time-out.
Data errors disable. Setting this bit disables parity errors on the local bus.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
4-42
Freescale Semiconductor
System Interface Unit (SIU)
Table 4-17. L_TESCR1 Field Descriptions (continued)
Bits
Name
18–19
—
20
DER
21–31
—
4.3.2.13
Description
Reserved, should be cleared.
Data error. Set when a core machine check is asserted due to parity errors in the local bus.
Reserved, should be cleared.
Local Bus Transfer Error Status and Control Register 2 (L_TESCR2)
The local bus transfer error status and control register 2 (L_TESCR2) is shown in Figure 4-34.
0
11
Field
12
—
Reset
15
PB
0000_0000_0000_0000
R/W
R/W
Addr
0x1004C
16
27
Field
28
BNK
Reset
31
—
0000_0000_0000_0000
R/W
R/W
Addr
0x1004E
Note: all bits are status bits and are cleared by writing 1s.
Figure 4-34. Local Bus Transfer Error Status and Control Register 2 (L_TESCR2)
Table 4-18 describes L_TESCR2 fields.
Table 4-18. L_TESCR2 Field Descriptions
Bits
Name
0–11
—
Reserved, should be cleared.
12–15
PB
Parity error on byte. There are four parity error status bits, one per 8-bit lane. A bit is set for the byte
that had a parity error.
16–27
BNK
Memory controller bank. There are twelve error status bits, one per memory controller bank. A bit is
set for the local bus memory controller bank that had an error. Note that BNK is invalid if the error
was not caused by ECC or PARITY checks.
28–31
—
4.3.2.14
Description
Reserved, should be cleared.
Time Counter Status and Control Register (TMCNTSC)
The time counter status and control register (TMCNTSC), shown in Figure 4-35, is used to enable the
different TMCNT functions and for reporting the source of the interrupts. The register can be read at any
time. Status bits are cleared by writing ones; writing zeros does not affect the value of a status bit.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
4-43
System Interface Unit (SIU)
.
0
Field
7
—
Reset
8
9
SEC
ALR
10
11
—
12
13
14
15
SIE
ALE
TCF
TCE
0000_0000_0000_0000
R/W
R/W
Addr
0x10220
Figure 4-35. Time Counter Status and Control Register (TMCNTSC)
Table 4-19 describes TMCNTSC fields.
Table 4-19. TMCNTSC Field Descriptions
Bits
Name
0–7
—
8
SEC
Once per second interrupt. This status bit is set every second and should be cleared by software.
9
ALR
Alarm interrupt. This status bit is set when the value of the TMCNT is equal to the value programmed
in the alarm register.
10–11
—
Reserved, should be cleared.
12
SIE
Second interrupt enable.
0 The time counter does not generate an interrupt when SEC is set.
1 The time counter generates an interrupt when SEC is set.
13
ALE
Alarm interrupt enable. If ALE = 1, the time counter generates an interrupt when ALR is set.
14
TCF
Time counter frequency. The input clock to the time counter may be either 4 MHz or 32 KHz. The
user should set the TCF bit according to the frequency of this clock.
0 The input clock to the time counter is 4 MHz.
1 The input clock to the time counter is 32 KHz.
See Section 4.1.2, “Timers Clock” for further details.
15
TCE
Time counter enable. Is not affected by soft or hard reset.
0 The time counter is disabled.
1 The time counter is enabled.
4.3.2.15
Description
Reserved, should be cleared.
Time Counter Register (TMCNT)
The time counter register (TMCNT), shown in Figure 4-36, contains the current value of the time counter.
The counter is reset to zero on PORESET reset or hard reset but is not effected by soft reset.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
4-44
Freescale Semiconductor
System Interface Unit (SIU)
0
15
Field
TMCNT
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x10224
16
31
Field
TMCNT
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x10226
Figure 4-36. Time Counter Register (TCMCNT)
4.3.2.16
Time Counter Alarm Register (TMCNTAL)
The time counter alarm register (TMCNTAL), shown in Figure 4-37, holds a value (ALARM). When the
value of TMCNT equals ALARM, a maskable interrupt is generated.
0
15
Field
ALARM
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x1022C
16
31
Field
ALARM
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x1222E
Figure 4-37. Time Counter Alarm Register (TMCNTAL)
Table 4-20 describes TMCNTAL fields.
Table 4-20. TMCNTAL Field Descriptions
Bits
Name
Description
0–31 ALARM The alarm interrupt is generated when ALARM field matches the corresponding TMCNT bits. The
resolution of the alarm is 1 second.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
4-45
System Interface Unit (SIU)
4.3.3
Periodic Interrupt Registers
The periodic interrupt registers are described in the following sections.
4.3.3.1
Periodic Interrupt Status and Control Register (PISCR)
The periodic interrupt status and control register (PISCR), shown in Figure 4-38, contains the interrupt
request level and the interrupt status bit. It also contains the controls for the 16 bits to be loaded in a
modulus counter.
0
Field
7
—
Reset
8
9
PS
12
—
13
14
15
PIE
PTF
PTE
0000_0000_0000_0000
R/W
R/W
Addr
0x10240
Figure 4-38. Periodic Interrupt Status and Control Register (PISCR)
Table 4-21 describes PISCR fields.
Table 4-21. PISCR Field Descriptions
Bits
Name
Description
0–7
—
Reserved, should be cleared.
8
PS
Periodic interrupt status. Asserted if the PIT issues an interrupt. The PIT issues an interrupt after the
modulus counter counts to zero. The PS bit can be negated by writing a one to PS. A write of zero has
no effect on this bit.
9–12
—
Reserved, should be cleared.
13
PIE
Periodic interrupt enable. If PIE = 1, the periodic interrupt timer generates an interrupt when PS = 1.
14
PTF
Periodic interrupt frequency. The input clock to the periodic interrupt timer may be either 4 MHz or
32 KHz. The user should set the PTF bit according to the frequency of this clock.
0 The input clock to the periodic interrupt timer is 4 MHz.
1 The input clock to the periodic interrupt timer is 32 KHz.
See Section 4.1.2, “Timers Clock,” for further details
15
PTE
Periodic timer enable. This bit controls the counting of the periodic interrupt timer. When the timer is
disabled, it maintains its old value. When the counter is enabled, it continues counting using the
previous value.
0 Disable counter.
1 Enable counter
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
4-46
Freescale Semiconductor
System Interface Unit (SIU)
4.3.3.2
Periodic Interrupt Timer Count Register (PITC)
The periodic interrupt timer count register (PITC), shown in Figure 4-39, contains the 16 bits to be loaded
in a modulus counter.
0
15
Field
PITC
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x10244
16
31
Field
—
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x10246
Figure 4-39. Periodic interrupt Timer Count Register (PITC)
Table 4-22 describes PITC fields.
Table 4-22. PITC Field Descriptions
Bits
Name
0–15
PITC
16–31
—
Description
Periodic interrupt timing count. Bits 0–15 are defined as the PITC, which contains the count for the
periodic timer. Setting PITC to 0xFFFF selects the maximum count period.
Reserved, should be cleared.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
4-47
System Interface Unit (SIU)
4.3.3.3
Periodic Interrupt Timer Register (PITR)
The periodic interrupt timer register (PITR), shown in Figure 4-40, is a read-only register that shows the
current value in the periodic interrupt down counter. The PITR counter is not affected by reads or writes
to it.
0
15
Field
PIT
Reset
0000_0000_0000_0000
R/W
Read Only
Addr
0x10248
16
31
Field
—
Reset
0000_0000_0000_0000
R/W
Read Only
Addr
0x1024A
Figure 4-40. Periodic Interrupt Timer Register (PITR)
Table 4-23 describes PITR fields.
Table 4-23. PITR Field Descriptions
Bits
Name
0–15
PITC
16–31
—
4.3.4
Description
Periodic interrupt timing count. Bits 0–15 are defined as the PIT. It contains the current count
remaining for the periodic timer. Writes have no effect on this field.
Reserved, should be cleared.
PCI Control Registers
Two pairs of registers detect accesses from the 60x bus side to the PCI bridge (other than PCI internal
registers accesses). Each pair consists of a PCI base register (PCIBRx) for comparing addresses and a
corresponding PCI mask register (PCIMSKx).
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
4-48
Freescale Semiconductor
System Interface Unit (SIU)
4.3.4.1
PCI Base Register (PCIBRx)
Figure 4-41 shows the PCI base register.
0
15
Field
BA
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x101AC (PCIBR0); 0x101B0 (PCIBR1)
16
Field
17
30
BA
—
Reset
31
V
0000_0000_0000_0000
R/W
R/W
Addr
0x101AE (PCIBR0); 0x101B2 (PCIBR1)
Figure 4-41. PCI Base Registers (PCIBRx)
Table 4-24 describes PCIBRx fields.
Table 4-24. PCIBRx Field Descriptions
Bits
Name
Description
0–16
BA
Base Address. The upper 17 bits of each base address register are compared to the address on the
60x bus address bus to determine if the access should be claimed by the PCI bridge. Used with
PCIMSKx[AM]
17–30
—
Reserved. Should be cleared.
31
V
Valid bit. Indicates that the contents of the PCIBRx and PCIMSKx pairs are valid.
0 This pair is invalid
1 This pair is valid
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
4-49
System Interface Unit (SIU)
4.3.4.2
PCI Mask Register (PCIMSKx)
Figure 4-42 shows the PCI mask register.
0
15
Field
AM
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x101C4 (PCIBR0); 0x101C8 (PCIBR1)
16
17
31
Field AM
—
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x101C6 (PCIBR0); 0x101CA (PCIBR1)
Figure 4-42. PCI Mask Register (PCIMSKx)
Table 4-25 describes PCIMSKx fields.
Table 4-25. PCIMSKx Field Descriptions
Bits
Name
31–17
—
Reserved. Should be cleared.
16–0
AM
Address Mask. Masks corresponding PCIBRx bits.
0 Corresponding address bits are masked.
1 Corresponding address bits are compared.
4.4
Description
SIU Pin Multiplexing
Some functions share pins. The actual pinout of the MPC8280 is shown in the hardware specifications.
The control of the actual functionality used on a specific pin is shown in Table 4-26.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
4-50
Freescale Semiconductor
System Interface Unit (SIU)
Table 4-26. SIU Pins Multiplexing Control
Pin Name
Pin Configuration Control
GBL/IRQ1
CI/BADDR29/IRQ2
WT/BADDR30/IRQ3
L2_HIT/IRQ4
CPU_BG/BADDR31/IRQ5/CINT
ABB/IRQ2
DBB/IRQ3
NC/DP0/RSRV/EXT_BR2
IRQ1/DP1/EXT_BG2
IRQ2/DP2/TLBISYNC/EXT_DBG2
IRQ3/DP3/CKSTP_OUT/EXT_BR3
IRQ4/DP4/CORE_SRESET/EXT_BG3
IRQ5/DP5/TBEN/EXT_DBG3/CINT
IRQ6/DP6/CSE0
IRQ7/DP7/CSE1
CS[10]/BCTL1
CS[11]/AP[0]
PCI_PAR/L_A14
SMI/PCI_FRAME/L_A15
PCI_TRDY/L_A16
CKSTOP_OUT/PCI_IRDY/L_A17
PCI_STOP/L_A18
PCI_DEVSEL/L_A19
PCI_IDSEL/L_A20
PCI_PERR/L_A21
PCI_SERR/L_A22
PCI_REQ0/L_A23
PCI_REQ1/L_A24
PCI_GNT0/L_A25
PCI_GNT1/L_A26
PCI_CLK/L_A27
CORE_SRESET/PCI_RST/L_A28
PCI_INTA/L_A29
PCI_REQ2/L_A30
AD[0–31]/LCL_D[0–31]
C/BE[0–3]/LCL_DP[0–3]
BNKSEL[0]/TC[0]/AP[1]/MODCK1
BNKSEL[1]/TC[1]/AP[2]/MODCK2
BNKSEL[2]/TC[2]/AP[3]/MODCK3
PWE[0–7]/PSDDQM[0–7]/PBS[0–7]
PSDA10/PGPL0
PSDWE/PGPL1
POE/PSDRAS/PGPL2
PSDCAS/PGPL3
PGTA/PUPMWAIT/PGPL4/PPBS
PSDAMUX/PGPL5
LBS[0–3]/LSDDQM[0–3]/LWE[0–3]
LGPL0/LSDA10
LGPL1/LSDWE
LGPL2/LSDRAS/LOE
LGPL3/LSDCAS
LPBS/LGPL4/LUPMWAIT/LGTA
LGPL5/LSDAMUX
Controlled by SIUMCR programming see Section 4.3.2.6, “SIU Module
Configuration Register (SIUMCR),” for more details.
Controlled dynamically according to the specific memory controller
machine that handles the current bus transaction.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
4-51
System Interface Unit (SIU)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
4-52
Freescale Semiconductor
Chapter 5
Reset
The MPC8280 has several inputs to the reset logic:
• Power-on reset (PORESET)
• External hard reset (HRESET)
• External soft reset (SRESET)
• Software watchdog reset
• Bus monitor reset
• Checkstop reset
• JTAG reset
All of these reset sources are fed into the reset controller and, depending on the source of the reset, different
actions are taken. The reset status register, described in Section 5.2, “Reset Status Register (RSR),”
indicates the last sources to cause a reset.
5.1
Reset Causes
Table 5-1 describes reset causes.
Table 5-1. Reset Causes
Name
Description
Power-on reset
(PORESET)
Input pin. Asserting this pin initiates the power-on reset flow that resets all the chip and configures
various attributes of the chip including its clock mode.
Hard reset
(HRESET)
This is a bidirectional I/O pin. The MPC8280 can detect an external assertion of HRESET only if it
occurs while the MPC8280 is not asserting reset. During HRESET, SRESET is asserted. HRESET
is an open-collector pin.
Soft reset
(SRESET)
Bidirectional I/O pin. The MPC8280 can only detect an external assertion of SRESET if it occurs
while the MPC8280 is not asserting reset. SRESET is an open-drain pin.
Software
watchdog reset
After the MPC8280’s watchdog counts to zero, a software watchdog reset is signaled. The enabled
software watchdog event then generates an internal hard reset sequence.
Bus monitor
reset
After the MPC8280’s bus monitor counts to zero, a bus monitor reset is asserted. The enabled bus
monitor event then generates an internal hard reset sequence.
Checkstop reset
If the core enters checkstop state and the checkstop reset is enabled (RMR[CSRE] = 1), checkstop
reset is asserted. The enabled checkstop event then generates an internal hard reset sequence.
JTAG reset
When JTAG logic asserts the JTAG soft reset signal, an internal soft reset sequence is generated.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
5-1
Reset
5.1.1
Reset Actions
The reset block has a reset control logic that determines the cause of reset, synchronizes it if necessary, and
resets the appropriate logic modules. The memory controller, system protection logic, interrupt controller,
and parallel I/O pins are initialized only on hard reset. Soft reset initializes the internal logic while
maintaining the system configuration. Because there is no soft nor hard reset in the 603e core, asserting
external SRESET generates a reset to the 603e core and a soft reset to the remainder of the device, The
impact on the given application is the reset to the core resets the MSR[IP] to the value in the HRCW[CIP],
see Table 5-7.
Table 5-2 identifies reset actions for each reset source.
Table 5-2. Reset Actions for Each Reset Source
Reset Source
Reset Logic
and PLL
States Reset
Clock
System
Configuration Module
Reset
Sampled
HRESET
Driven
Other
SRESET
Internal
Driven
1
Logic Reset
Core
Reset
Power-on reset
Yes
Yes
Yes
Yes
Yes
Yes
Yes
External hard reset
Software watchdog
Bus monitor
Checkstop
No
Yes
Yes
Yes
Yes
Yes
Yes
JTAG reset
External soft reset
No
No
No
No
Yes
Yes
Yes
1
Includes all other CPM and core logic not explicitly noted elsewhere in the table.
5.1.2
Power-On Reset Flow
Assertion of the PORESET external pin initiates the power-on reset flow. PORESET should be asserted
externally for at least 16 input clock cycles after external power to the chip reaches at least 2/3 Vcc. The
value driven on RSTCONF while PORESET changes from assertion to negation determines the chip
configuration. If RSTCONF is negated (driven high) while PORESET changes, the chip acts as a
configuration slave. If RSTCONF is asserted while PORESET changes, the chip acts as a configuration
master. Section 5.4, “Reset Configuration,” explains the configuration sequence and the terms
‘configuration master’ and ‘configuration slave.’
Directly after the negation of PORESET and choice of the reset operation mode as configuration master
or configuration slave, the MPC8280 starts the configuration process. The MPC8280 asserts HRESET and
SRESET throughout the power-on reset process, including configuration. Configuration takes 1,024
CLOCKIN cycles, after which MODCK[1–3] are sampled to determine the chips working mode. Next the
MPC8280 halts until the main PLL locks. As described in Section 10.6, “Clock Configuration Modes,” the
main PLL locks according to MODCK[1–3], which are sampled, and to MODCK_HI (MODCK[4–7])
taken from the reset configuration word. The main PLL lock can take up to 200 µs depending on the
specific chip. During this time HRESET and SRESET are asserted. When the main PLL is locked, the
clock block starts distributing clock signals in the chip. HRESET remains asserted for another 512 clocks
and is then released. The SRESET is released three clocks later.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
5-2
Freescale Semiconductor
Reset
Figure 5-4 shows the power-on reset flow.
PORESET
Input
External
pin is
asserted
for min 16
RSTCONF is sampled for
master determination
PORESET
Internal
MODCK[1–3] are
sampled. MODCK_HI
bits are ready for PLL
HRESET
Output
PLL is locked (no
external indication)
SRESET
Output
PLL locking period
PORESET to internal logic is
extended for 1024 CLKIN.
HRESET /SRESET are
extended for 512/515
CLKIN (respectively), from
PLL lock time.
Interval depends on
PLL locking time.
In reset configuration mode:
reset configuration
sequence occurs in this
period.
Figure 5-1. Power-on Reset Flow
5.1.3
HRESET Flow
The HRESET flow may be initiated externally by asserting HRESET or internally when the chip detects
a reason to assert HRESET. In both cases the chip continues asserting HRESET and SRESET throughout
the HRESET flow. The HRESET flow begins with the hard reset configuration sequence, which
configures the chip as explained in Section 5.4, “Reset Configuration.” After the chip asserts HRESET and
SRESET for 1,024 input clock cycles, it releases both signals and exits the HRESET flow. An external
pull-up resistor should negate the signals. After negation is detected, a 16-cycle period is taken before
testing the presence of an external (hard/soft) reset.
5.1.4
SRESET Flow
The SRESET flow may be initiated externally by asserting SRESET or internally when the chip detects a
cause to assert SRESET. In both cases the chip asserts SRESET for 512 input clock cycles, after which the
chip releases SRESET and exits the SRESET flow. An external pull-up resistor should negate SRESET;
after negation is detected, a 16-cycle period is taken before testing the presence of an external (hard/soft)
reset. While SRESET is asserted, internal hardware is reset but hard reset configuration does not change.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
5-3
Reset
5.2
Reset Status Register (RSR)
The reset status register (RSR), shown in Figure 5-2, is memory-mapped into the MPC8280’s SIU register
map.
0
15
Field
—
R/W
R/W
Reset
0000_0000_0000_0000
Addr
0x10C90
16
25
Field
—
26
27
JTRS CSRS
R/W
28
SWRS
29
30
31
BMRS ESRS EHRS
R/W
Reset
0000_0000_0000_0011
Addr
0x10C92
Figure 5-2. Reset Status Register (RSR)
Table 5-3 describes RSR fields.
Table 5-3. RSR Field Descriptions
Bits
Name
Function
0–25
—
26
JTRS
27
CSRS Check stop reset status. When the core enters a checkstop state and the checkstop reset is enabled
by the RMR[CSRE], CSRS is set and it remains set until software clears it. CSRS is cleared by
writing a 1 to it (writing zero has no effect).
0 No enabled checkstop reset event occurred
1 An enabled checkstop reset event occurred
28
SWRS Software watchdog reset status. When a software watchdog expire event (which causes a reset) is
detected, the SWRS bit is set and remains that way until the software clears it. SWRS is cleared by
writing a 1 to it (writing zero has no effect).
0 No software watchdog reset event occurred
1 A software watchdog reset event has occurred
29
BMRS Bus monitor reset status. When a bus monitor expire event (which causes a reset) is detected,
BMRS is set and remains set until the software clears it. BMRS can be cleared by writing a 1 to it
(writing zero has no effect).
0 No bus monitor reset event has occurred
1 A bus monitor reset event has occurred
Reserved, should be cleared.
JTAG reset status. When the JTAG reset request is set, JTRS is set and remains set until software
clears it. JTRS is cleared by writing a 1 to it (writing zero has no effect).
0 No JTAG reset event occurred
1 A JTAG reset event occurred
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
5-4
Freescale Semiconductor
Reset
Table 5-3. RSR Field Descriptions (continued)
Bits
Name
Function
30
ESRS External soft reset status. When an external soft reset event is detected, ESRS is set and it remains
that way until software clears it. ESRS is cleared by writing a 1 to it (writing zero has no effect).
0 No external soft reset event has occurred
1 An external soft reset event has occurred
31
EHRS External hard reset status. When an external hard reset event is detected, EHRS is set and it
remains set until software clears it. EHRS is cleared by writing a 1 (writing zero has no effect).
0 No external hard reset event has occurred
1 An external hard reset event has occurred
NOTE
The reset status register accumulates reset events. For example, because
software watchdog expiration results in a hard reset, which in turn results in
a soft reset, RSR[SWRS], RSR[ESRS] and RSR[EHRS] are all set after a
software watchdog reset.
5.3
Reset Mode Register (RMR)
The reset mode register (RMR), shown in Figure 5-3, is memory-mapped into the SIU register map.
0
15
Field
—
R/W
R/W
Reset
0000_0000_0000_0000
Addr
0x10C94
16
Field
R/W
30
—
31
CSRE
R/W
Reset
0000_0000_0000_0000
Addr
0x10C96
Figure 5-3. Reset Mode Register (RMR)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
5-5
Reset
Table 5-4 describes RMR fields.
Table 5-4. RMR Field Descriptions
Bits
Name
0–30
—
31
5.4
Function
Reserved, should be cleared.
CSRE Checkstop reset enable. The core can enter checkstop mode as the result of several exception
conditions. Setting CSRE configures the chip to perform a hard reset sequence whenever the core
enters checkstop state.
0 Reset not generated when core enters checkstop state.
1 Reset generated when core enters checkstop state.
Note: When the core is disabled, CSRE must be cleared.
Reset Configuration
Various features may be configured during hard reset or power-on reset. For example, one configurable
features is core disable, which can be used to configure a system that uses two MPC8280s, one a slave
device and the other a the host with an active core. Most configurable features are reconfigured whenever
HRESET is asserted. However, the clock mode is configured only when PORESET is asserted.
The 32-bit hard reset configuration word is described in Section 5.4.1, “Hard Reset Configuration Word.”
The reset configuration sequence is designed to support a system that uses up to eight MPC8280 chips,
each configured differently. It needs no additional glue logic for reset configuration.
The description below explains the operation of this sequence with regard to a multiple-MPC8280 system.
This and other simpler systems are described in Section 5.4.2, “Hard Reset Configuration Examples.” In
a typical multi-MPC8280 system, one MPC8280 should act as the configuration master while all other
MPC8280s should act as configuration slaves. The configuration master in the system typically reads the
various configuration words from EPROM in the system and uses them to configure itself as well as the
configuration slaves. How the MPC8280 acts during reset configuration is determined by the value of the
RSTCONF input while PORESET changes from assertion to negation. If RSTCONF is asserted while
PORESET changes, MPC8280 is a configuration master; otherwise, it is a slave.
In a typical multiple-MPC8280 system, RSTCONF input of the configuration master should be hard wired
to ground, while RSTCONF inputs of other chips should be connected to the high-order address bits of the
configuration master, as described in Table 5-5.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
5-6
Freescale Semiconductor
Reset
Table 5-5. RSTCONF Connections in Multiple-MPC8280 Systems
Configured Device
RSTCONF Connection
Configuration master
GND
First configuration slave
A0
Second configuration slave
A1
Third configuration slave
A2
Fourth configuration slave
A3
Fifth configuration slave
A4
Sixth configuration slave
A5
Seventh configuration slave
A6
The configuration words for all MPC8280s are assumed to reside in an EPROM connected to CS0 of the
configuration master. Because the port size of this EPROM is not known to the configuration master,
before reading the configuration words, the configuration master reads all configuration words
byte-by-byte only from locations that are independent of port size.
Table 5-6. shows addresses that should be used to configure the various MPC8280s. Byte addresses that
do not appear in this table have no effect on the configuration of the MPC8280 chips. The values of the
bytes in Table 5-6 are always read on byte lane D[0–7] regardless of the port size
.
Table 5-6. Configuration EPROM Addresses
Configured Device
Byte 0 Address
Byte 1 Address
Byte 2 Address
Byte 3 Address
Configuration master
0x00
0x08
0x10
0x18
First configuration slave
0x20
0x28
0x30
0x38
Second configuration slave
0x40
0x48
0x50
0x58
Third configuration slave
0x60
0x68
0x70
0x78
Fourth configuration slave
0x80
0x88
0x90
0x98
Fifth configuration slave
0xA0
0xA8
0xB0
0xB8
Sixth configuration slave
0xC0
0xC8
0xD0
0xD8
Seventh configuration slave
0xE0
0xE8
0xF0
0xF8
The configuration master first reads a value from address 0x00 then reads a value from addresses 0x08,
0x10, and 0x18. These four bytes are used to form the configuration word of the configuration master,
which then proceeds reading the bytes that form the configuration word of the first slave device. The
configuration master drives the whole configuration word on D[0–31] and toggles its A0 address line.
Each configuration slave uses its RSTCONF input as a strobe for latching the configuration word during
HRESET assertion time. Thus, the first configuration slave whose RSTCONF input is connected to
configuration master’s A0 output latches the word driven on D[0–31] as its configuration word. In this way
the configuration master continues to configure all MPC8280 chips in the system. The configuration
master always reads eight configuration words regardless of the number of MPC8280 parts in the system.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
5-7
Reset
In a simple system that uses one stand-alone MPC8280, it is possible to use the default hard reset
configuration word (all zeros). This is done by tying RSTCONF input to VCC. Another scenario may be
a system which has no boot EPROM. In this case the user can configure the MPC8280 as a configuration
slave by driving RSTCONF to 1 during PORESET assertion and then applying a negative pulse on
RSTCONF and an appropriate configuration word on D[0–31]. In such a system, asserting HRESET in the
middle of operation causes the MPC8280 to return to the configuration programmed after PORESET
assertion (not the default configuration represented by configuration word of all zeros).
5.4.1
Hard Reset Configuration Word
The contents of the hard reset configuration word are shown in Figure 5-4.
0
1
2
3
Field EARB EXMC CDIS EBM
4
5
BPS
Reset
Field
6
7
CIP
ISPS
8
9
L2CPC
10
11
DPPC
12
13
PLLBP
15
ISB
0000_0000_0000_0000
16
17
BMS
BBD
Reset
18
19
MMR
20
21
LBPC
22
23
APPC
24
25
CS10PC
26
27
ALD_EN
—
28
31
MODCK_H
0000_0000_0000_0000
Figure 5-4. Hard Reset Configuration Word
Table 5-7 describes hard reset configuration word fields.
Table 5-7. Hard Reset Configuration Word Field Descriptions
Bits
Name
Description
0
EARB1
External arbitration. Defines the initial value for ACR[EARB]. If EARB = 1, external arbitration is
assumed. See Section 4.3.2.2, “60x Bus Arbiter Configuration Register (PPC_ACR).”
1
EXMC
External MEMC. Defines the initial value of BR0[EMEMC]. If EXMC = 1, an external memory
controller is assumed. See Section 11.3.1, “Base Registers (BRx).”
2
CDIS1
Core disable. Defines the initial value for the SIUMCR[CDIS].
0 The core is active. See Section 4.3.2.6, “SIU Module Configuration Register (SIUMCR).”
1 The core is disabled. In this mode the MPC8280 functions as a slave.
3
EBM1
External bus mode. Defines the initial value of BCR[EBM]. See Section 4.3.2.1, “Bus
Configuration Register (BCR).”
4–5
BPS
Boot port size. Defines the initial value of BR0[PS], the port size for memory controller bank 0.
00 64-bit port size
01 8-bit port size
10 16-bit port size
11 32-bit port size
See Section 11.3.1, “Base Registers (BRx).”
6
CIP1
Core initial prefix. Defines the initial value of MSR[IP]. Exception prefix. The setting of this bit
specifies whether an exception vector offset is prepended with Fs or 0s. In the following
description, nnnnn is the offset of the exception vector.
0 MSR[IP] = 1 (default). Exceptions are vectored to the physical address 0xFFFn_nnnn
1 MSR[IP] = 0 Exceptions are vectored to the physical address 0x000n_nnnn.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
5-8
Freescale Semiconductor
Reset
Table 5-7. Hard Reset Configuration Word Field Descriptions (continued)
Bits
Name
Description
7
ISPS1
8–9
L2CPC1
L2 cache pins configuration. Defines the initial value of SIUMCR[L2CPC]. See Section 4.3.2.6,
“SIU Module Configuration Register (SIUMCR).”
10–11
DPPC1
Data parity pin configuration. Defines the initial value of SIUMCR[DPPC]. For more details refer
to Section 4.3.2.6, “SIU Module Configuration Register (SIUMCR).”
12
PLLBP
PLL bypass
0 Normal operation
1 Bypass CPM PLL
13–15
ISB
Initial internal space base select. Defines the initial value of IMMR[0–14] and determines the
base address of the internal memory space.
000 0x0000_0000
001 0x00F0_0000
010 0x0F00_0000
011 0x0FF0_0000
100 0xF000_0000
101 0xF0F0_0000
110 0xFF00_0000
111 0xFFF0_0000
See Section 4.3.2.7, “Internal Memory Map Register (IMMR).”
16
BMS
Boot memory space. Defines the initial value for BR0[BA]. There are two possible boot memory
regions: HIMEM and LOMEM.
0 0xFE00_0000—0xFFFF_FFFF
1 0x0000_0000—0x01FF_FFFF
See Section 11.3.1, “Base Registers (BRx).”
17
BBD1
Bus busy disable. Defines the initial value of SIUMCR[BBD]. See Section 4.3.2.6, “SIU Module
Configuration Register (SIUMCR).”
18–19
MMR
Mask masters requests. Defines the initial value of SIUMCR[MMR]. See Section 4.3.2.6, “SIU
Module Configuration Register (SIUMCR).”
20–21
LBPC 1
Internal space port size. Defines the initial value of BCR[ISPS]. Setting ISPS configures the
MPC8280 to respond to accesses from a 32-bit external master to its internal space. See
Section 4.3.2.1, “Bus Configuration Register (BCR).”
Local bus pin configuration. Defines the value of SIUMCR[LBPC]. See Section 4.3.2.6, “SIU
Module Configuration Register (SIUMCR).”
00 Local bus pins function as local bus
01 Local bus pins function as PCI bus
10 Local bus pins function as core pins
11 Reserved
22–23
APPC1
24–25
CS10PC 1
Address parity pin configuration. Defines the initial value of SIUMCR[APPC]. See
Section 4.3.2.6, “SIU Module Configuration Register (SIUMCR).”
CS10 pin configuration. Defines the initial value of SIUMCR[CS10PC]. See Section 4.3.2.6,
“SIU Module Configuration Register (SIUMCR).”
Note: During the reset configuration sequence, the BCTL1/CS10 pin toggles like POE of the 60x
bus GPCM, regardless of the configuration of the reset configuration word. After the reset
configuration sequence, the BCTL1/CS10 pin behaves according to the configuration of
SIUMCR[CS10PC].
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
5-9
Reset
Table 5-7. Hard Reset Configuration Word Field Descriptions (continued)
Bits
26
27
Name
ALD_EN
—
Description
CP auto load enable. Allows the CP to automatically load the essential PCI configuration
registers from the EEPROM during reset.
0 CP auto load is disabled.
1 CP auto load is enabled.
Reserved, should be cleared.
28–31 MODCK_H High-order bits of the MODCK bus, which determine the clock reset configuration. See
Chapter 10, “Clocks and Power Control,” for details.
Note: If the device is configured to PCI mode (PCI_MODE is driven low), this field has no effect
and the value for MODCK_H is loaded directly from the MODCK_H pins. Note that the
value of the MODCK_H bits are derived from the dedicated PCI_MODCK_H[0:3] pins
when operating in PCI mode.
1
The user should exercise caution when changing this bit. This bit has an immediate effect on the external bus and
may result in unstable system operation.
5.4.2
Hard Reset Configuration Examples
This section presents some examples of hard reset configurations in different systems.
5.4.2.1
Single MPC8280 with Default Configuration
This is the simplest configuration scenario. It can be used if the default values achieved by clearing the
hard reset configuration word are desired. This is applicable only for systems using single-MPC8280 bus
mode (as opposed to 60x bus mode). To enter this mode, tie RSTCONF to VCC as shown in Figure 5-5.
The MPC8280 does not access the boot EPROM; it is assumed that the default configuration is used upon
exiting hard reset.
PORESET
Vcc
Configuration
Slave Chip
HRESET
A[0–31]
PORESET
Vcc
D[0–31]
RSTCONF
Figure 5-5. Single Chip with Default Configuration
5.4.2.2
Single MPC8280 Configured from Boot EPROM
For a configuration that differs from the default, the MPC8280 can be used as a configuration master by
tying RSTCONF to GND as shown in Figure 5-6. The MPC8280 can access the boot EPROM. It is
assumed the configuration is as defined there upon exiting hard reset.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
5-10
Freescale Semiconductor
Reset
PORESET
Configuration Master Chip
HRESET
Address Bus
EPROM Control Signals
VCC
Boot EPROM
A[..]
A[0–31]
D[0–31]
RSTCONF
Data Bus
PORESET
D[0–7]
Figure 5-6. Configuring a Single Chip from EPROM
5.4.2.3
Multiple MPC8280s Configured from Boot EPROM
For a complex system with multiple MPC8280 devices that may each be configured differently,
configuration is done by assigning one configuration master and multiple configuration slaves. The
MPC8280 that controls the boot EPROM should be the configuration master—RSTCONF tied to GND.
The RSTCONF inputs of the other MPC8280 devices are tied to the address bus lines, thus assigning them
as configuration slaves. See Figure 5-7.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
5-11
Reset
PORESET
EPROM Control Signals
Configuration Master Chip
HRESET
Address Bus
VCC
Boot EPROM
A[..]
A[0–31]
PORESET
D[0–7]
D[0–31]
HRESET
PORESET
Configuration Slave Chip 1
D[0–31]
RSTCONF
HRESET
PORESET
Data Bus
RSTCONF
A0
Configuration Slave Chip 2
D[0–31]
RSTCONF
A1
Configuration Slave Chip 7
HRESET
PORESET
D[0–31]
RSTCONF
A6
Figure 5-7. Configuring Multiple Chips
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
5-12
Freescale Semiconductor
Reset
In this system, the configuration master initially reads its own configuration word. It then reads other
configuration words and drives them to the configuration slaves by asserting RSTCONF. As Figure 5-7
shows, this complex configuration is done without additional glue logic. The configuration master controls
the whole process by asserting the EPROM control signals and the system’s address signals as needed.
5.4.2.4
Multiple MPC8280s in a System with No EPROM
In some cases, the configuration master capabilities of the MPC8280 cannot be used. This can happen for
example if there is no boot EPROM in the system or the boot EPROM is not controlled by an MPC8280.
If this occurs, the user must do one of the following:
• Accept the default configuration,
• Emulate the configuration master actions in external logic (where the MPC8280 is a configuration
slave).
• The external hardware should be connected to all RSTCONF pins of the different devices and to
the upper 32 bits of the data bus. During PORESET, the rising edge the external hardware should
negate all RSTCONF inputs to put all of the devices in their configuration slave mode. For 1,024
clocks after PORESET negation, the external hardware can configure the different devices by
driving appropriate configuration words on the data bus and asserting RSTCONF for each device
to strobe the data being received.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
5-13
Reset
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
5-14
Freescale Semiconductor
Part III
The Hardware Interface
Intended Audience
Part III is intended for system designers who need to understand how each MPC8280 signal works and
how those signals interact.
Contents
Part III describes external signals, clocking, memory control, and power management of the MPC8280.
It contains the following chapters:
• Chapter 6, “External Signals,” shows a functional pinout of the MPC8280 and describes the
MPC8280 signals.
• Chapter 7, “60x Signals,” describes signals on the 60x bus.
• Chapter 8, “The 60x Bus,” describes the operation of the bus used by PowerPC processors.
• Chapter 10, “Clocks and Power Control,” describes the clocking architecture of the MPC8280.
• Chapter 9, “PCI Bridge,” describes how the PCI bridge enables the MPC8280 to bridge PCI agents
gluelessly to a host processor that implements the PowerPC architecture and how it is compliant
with PCI Specification Revision 2.2.
• Chapter 11, “Memory Controller,” describes the memory controller, which controlling a maximum
of eight memory banks shared between a general-purpose chip-select machine (GPCM) and three
user-programmable machines (UPMs).
• Chapter 12, “Secondary (L2) Cache Support,” provides information about implementation and
configuration of a level-2 cache.
• Chapter 13, “IEEE 1149.1 Test Access Port,” describes the dedicated user-accessible test access
port (TAP), which is fully compatible with the IEEE 1149.1 Standard Test Access Port and
Boundary Scan Architecture.
Suggested Reading
This section lists additional reading that provides background for the information in this manual as well as
general information about the PowerPC architecture.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
III-1
MPC82xx Documentation
Supporting documentation for the MPC8280 can be accessed through the world-wide web at
www.freescale.com. This documentation includes technical specifications, reference materials, and
detailed applications notes.
Conventions
This document uses the following notational conventions:
Bold entries in figures and tables showing registers and parameter RAM should
Bold
be initialized by the user.
mnemonics
Instruction mnemonics are shown in lowercase bold.
italics
Italics indicate variable command parameters, for example, bcctrx.
Book titles in text are set in italics.
0x0
0b0
REG[FIELD]
x
n
¬
&
|
Prefix to denote hexadecimal number
Prefix to denote binary number
Abbreviations or acronyms for registers or buffer descriptors are shown in
uppercase text. Specific bits, fields, or numerical ranges appear in brackets. For
example, MSR[LE] refers to the little-endian mode enable bit in the machine state
register.
In certain contexts, such as in a signal encoding or a bit field, indicates a don’t
care.
Indicates an undefined numerical value
NOT logical operator
AND logical operator
OR logical operator
Acronyms and Abbreviations
Table i contains acronyms and abbreviations used in this document. Note that the meanings for some
acronyms (such as SDR1 and DSISR) are historical, and the words for which an acronym stands may not
be intuitively obvious.
Table I-i. Acronyms and Abbreviated Terms
Term
Meaning
BD
Buffer descriptor
BIST
Built-in self test
BRI
Basic rate interface
CAM
Content-addressable memory
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
III-2
Freescale Semiconductor
Table I-i. Acronyms and Abbreviated Terms (continued)
Term
Meaning
CPM
Communications processor module
CRC
Cyclic redundancy check
DMA
Direct memory access
DPLL
Digital phase-locked loop
DRAM
Dynamic random access memory
DSISR
Register used for determining the source of a DSI exception
EA
Effective address
EEST
Enhanced Ethernet serial transceiver
GCI
General circuit interface
GPCM
General-purpose chip-select machine
HDLC
High-level data link control
I2C
Inter-integrated circuit
IDL
Inter-chip digital link
IEEE
Institute of Electrical and Electronics Engineers
IrDA
Infrared Data Association
ISDN
Integrated services digital network
JTAG
Joint Test Action Group
LIFO
Last-in-first-out
LRU
Least recently used
LSB
Least-significant byte
lsb
Least-significant bit
LSU
Load/store unit
MAC
Multiply accumulate
MMU
Memory management unit
MSB
Most-significant byte
msb
Most-significant bit
MSR
Machine state register
NMSI
Nonmultiplexed serial interface
OSI
Open systems interconnection
PCI
Peripheral component interconnect
PCMCIA
Personal Computer Memory Card International Association
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
III-3
Table I-i. Acronyms and Abbreviated Terms (continued)
Term
Meaning
PRI
Primary rate interface
Rx
Receive
SCC
Serial communications controller
SCP
Serial control port
SDLC
Synchronous data link control
SDMA
Serial DMA
SI
Serial interface
SIU
System interface unit
SMC
Serial management controller
SNA
Systems network architecture.
SPI
Serial peripheral interface
SPR
Special-purpose register
SRAM
Static random access memory
TDM
Time-division multiplexed
TLB
Translation lookaside buffer
TSA
Time-slot assigner
Tx
Transmit
UART
Universal asynchronous receiver/transmitter
UISA
User instruction set architecture
UPM
User-programmable machine
USART
Universal synchronous/asynchronous receiver/transmitter
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
III-4
Freescale Semiconductor
Chapter 6
External Signals
This chapter describes the external signals. A more detailed description of 60x bus signals is provided in
Chapter 8, “The 60x Bus.”
6.1
Functional Pinout
Figure 6-1 shows MPC8280 signals grouped by function. Note that many signals are multiplexed and this
figure does not indicate how these signals are multiplexed.
NOTE
A bar over a signal name indicates that the signal is active low—for
example, BB (bus busy). Active-low signals are referred to as asserted
(active) when they are low and negated when they are high. Signals that are
not active low, such as TSIZ[0–1] (transfer size signals) are referred to as
asserted when they are high and negated when they are low.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
6-1
External Signals
VCCSYN/GNDSYN/VCCSYN1//VDDH/ ⎯⎯⎯> 100
VDD/VSS
PCI_PAR/L_A14 <⎯⎯> 1
SMI/PCI_FRAME/L_A15 <⎯⎯> 1
PCI_TRDY/L_A16 <⎯⎯> 1
CKSTOP_OUT/PCI_IRDY/L_A17 <⎯⎯> 1
PCI_STOP/L_A18 <⎯⎯> 1
PCI_DEVSEL/L_A19 <⎯⎯> 1
PCI_IDSEL/L_A20 <⎯⎯> 1
PCI_PERR/L_A21 <⎯⎯> 1
PCI_SERR/L_A22 <⎯⎯> 1
PCI_REQ0/L_A23 <⎯⎯> 1
CPCI_HS_ES/PCI_REQ1/L_A24 <⎯⎯> 1
PCI_GNT0/L_A25 <⎯⎯> 1
CPCI_HS_LED/PCI_GNT1/L_A26 <⎯⎯⎯ 1
CPCI_HS_ENUM/GNT2/L_A27 <⎯⎯> 1
CORE_SRESET/PCI_RST/L_A28 <⎯⎯> 1
PCI_INTA/L_A29 <⎯⎯> 1
PCI_REQ2/L_A30 <⎯⎯> 1
DLLOUT/L_A31 <⎯⎯> 1
PCI_AD[31-0]/LCL_D[0–31] <⎯⎯> 32
PCI_C/BE[3-0]/LCL_DP[0–3] <⎯⎯> 4
32 <⎯⎯>
L
O
C
A
L
B
U
S
B
U
S
PCI_CFG[3–0]/LBS[0–3]/
LSDDQM[0–3]/LWE[0–3]
PCI_MODCK_H0/LGPL0/LSDA10
PCI_MODCK_H1/LGPL1/LSDWE
PCI_MODCK_H2/LGPL2/LSDRAS/LOE
PCI_MODCK_H3/LGPL3/LSDCAS
LPBS/LGPL4/LUPMWAIT/LGTA
PCI_MODCK/LGPL5
LWR
<⎯⎯⎯
4
<⎯⎯⎯
<⎯⎯⎯
<⎯⎯⎯
<⎯⎯⎯
<⎯⎯>
<⎯⎯>
<⎯⎯>
1
1
1
1
1
1
1
M
E
M
C
PA[0–31]
PB[4–31]
PC[0–31]
PD[4–31]
<⎯⎯>
<⎯⎯>
<⎯⎯>
<⎯⎯>
32
28
32
28
P
I
O
PCI_RST/PORESET⎯⎯⎯>
RSTCONF⎯⎯⎯>
HRESET<⎯⎯>
SRESET<⎯⎯>
QREQ<⎯⎯⎯
XFC⎯⎯⎯>
CLKIN1⎯⎯⎯>
TRIS⎯⎯⎯>
BNKSEL[0]/TC[0]/AP[1]/MODCK1<⎯⎯>
BNKSEL[1]/TC[1]/AP[2]/MODCK2<⎯⎯>
BNKSEL[2]/TC[2]/AP[3]/MODCK3<⎯⎯>
PCI_MODE ⎯⎯⎯>
CLKIN2 ⎯⎯⎯>
NC ⎯⎯⎯>
1
1
1
1
1
1
1
1
1
1
1
1
1
2
6
0
x
R
S
T
C
L
K
M
E
M
C
J
T
A
G
5
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
64
1
1
1
1
1
1
1
1
1
1
1
1
1
10
1
1
2
1
1
8
1
1
1
1
1
1
1
1
1
1
1
A[0–31]
<⎯⎯> TT[0–4]
<⎯⎯> TSIZ[0–3]
<⎯⎯> TBST
<⎯⎯> GBL/IRQ1
<⎯⎯> CI/BADDR29/IRQ2
<⎯⎯> WT/BADDR30/IRQ3
<⎯⎯⎯ L2_HIT/IRQ4
<⎯⎯> CPU_BG/BADDR31/IRQ5/CINT
⎯⎯⎯> CPU_DBG
⎯⎯⎯> CPU_BR
<⎯⎯> BR
<⎯⎯> BG
<⎯⎯> ABB/IRQ2
<⎯⎯> TS
<⎯⎯> AACK
<⎯⎯> ARTRY
<⎯⎯> DBG
<⎯⎯> DBB/IRQ3
<⎯⎯> D[0–63]
<⎯⎯> NC/DP0/RSRV/EXT_BR2
<⎯⎯> IRQ1/DP1/EXT_BG2
<⎯⎯> IRQ2/DP2/TLBISYNC/EXT_DBG2
<⎯⎯> IRQ3/DP3/CKSTP_OUT/EXT_BR3
<⎯⎯> IRQ4/DP4/CORE_SRESET/EXT_BG3
<⎯⎯> IRQ5/DP5/TBEN/EXT_DBG3/CINT
<⎯⎯> IRQ6/DP6/CSE0
<⎯⎯> IRQ7/DP7/CSE1
<⎯⎯> PSDVAL
<⎯⎯> TA
<⎯⎯> TEA
<⎯⎯> IRQ0/NMI_OUT
<⎯⎯> IRQ7/INT_OUT/APE
⎯⎯⎯> CS[0–9]
<⎯⎯> CS[10]/BCTL1
<⎯⎯> CS[11]/AP[0]
⎯⎯⎯> BADDR[27–28]
⎯⎯⎯> ALE
⎯⎯⎯> BCTL0
⎯⎯⎯> PWE[0–7]/PSDDQM[0–7]/PBS[0–7]
⎯⎯⎯> PSDA10/PGPL0
⎯⎯⎯> PSDWE/PGPL1
⎯⎯⎯> POE/PSDRAS/PGPL2
⎯⎯⎯> PSDCAS/PGPL3
<⎯⎯> PGTA/PUPMWAIT/PGPL4/PPBS
⎯⎯⎯> PSDAMUX/PGPL5
<⎯⎯− TMS
<⎯⎯⎯ TDI
<⎯⎯− TCK
<⎯⎯− TRST
−⎯⎯> TDO
Figure 6-1. MPC8280 External Signals
6.2
Signal Descriptions
The MPC8280 system bus, shown in Table 6-1, consists of all the signals that interface with the external
bus. Many of these pins perform different functions, depending on how the user assigns them.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
6-2
Freescale Semiconductor
External Signals
Table 6-1. External Signals
Signal
Description
BR
60x bus request—This is an output when an external arbiter is used and an input when an internal
arbiter is used. As an output the MPC8280 asserts this pin to request ownership of the 60x bus.
As an input an external master should assert this pin to request 60x bus ownership from the
internal arbiter.
BG
60x bus grant—This is an output when an internal arbiter is used and an input when an external
arbiter is used. As an output the MPC8280 asserts this pin to grant 60x bus ownership to an
external bus master. As an input the external arbiter should assert this pin to grant 60x bus
ownership to the MPC8280.
ABB
60x address bus busy—(Input/output) As an output the MPC8280 asserts this pin for the duration
of the address bus tenure. Following an AACK, which terminates the address bus tenure, the
MPC8280 negates ABB for a fraction of a bus cycle and than stops driving this pin. As an input
the MPC8280 will not assume 60x bus ownership as long as it senses this pin is asserted by an
external 60x bus master.
IRQ2
Interrupt Request 2—This input is one of the eight external lines that can request (by means of
the internal interrupt controller) a service routine from the core.
TS
60x bus transfer start—(Input/output) Assertion of this pin signals the beginning of a new address
bus tenure. The MPC8280 asserts this signal when one of its internal 60x bus masters (core,
DMA, PCI bridge) begins an address tenure. When the MPC8280 senses this pin being asserted
by an external 60x bus master, it will respond to the address bus tenure as required (snoop if
enabled, access internal MPC8280 resources, memory controller support).
A[0–31]
60x address bus—These are input/output pins. When the MPC8280 is in external master bus
mode, these pins function as the 60x address bus. The MPC8280 drives the address of its
internal 60x bus masters and respond to addresses generated by external 60x bus masters.
When the MPC8280 is in internal master bus mode, these pins are used as address lines
connected to memory devices and controlled by the MPC8280’s memory controller.
TT[0–4]
60x bus transfer type—These are input/output pins. The 60x bus master drives these pins during
the address tenure to specify the type of the transaction.
TBST
60x bus transfer burst—(Input/output) The 60x bus master asserts this pin to indicate that the
current transaction is a burst transaction (transfers 4 double words).
TSIZ[0–3]
60x transfer size—These are input/output pins. The 60x bus master drives these pins with a value
indicating the amount of bytes transferred in the current transaction.
AACK
60x address acknowledge—This is an input/output signal. A 60x bus slave asserts this signal to
indicate that it identified the address tenure. Assertion of this signal terminates the address
tenure.
ARTRY
60x address retry—(Input/output) Assertion of this signal indicates that the bus transaction
should be retried by the 60x bus master. The MPC8280 asserts this signal to enforce data
coherency with its internal cache and to prevent deadlock situations.
DBG
60x data bus grant—This is an output when an internal arbiter is used and an input when an
external arbiter is used. As an output the MPC8280 asserts this pin to grant 60x data bus
ownership to an external bus master. As an input the external arbiter should assert this pin to
grant 60x data bus ownership to the MPC8280.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
6-3
External Signals
Table 6-1. External Signals (continued)
Signal
Description
DBB
60x data bus busy—(Input/output) As an output the MPC8280 asserts this pin for the duration of
the data bus tenure. Following a TA, which terminates the data bus tenure, the MPC8280 negates
DBB for a fraction of a bus cycle and than stops driving this pin. As an input, the MPC8280 does
not assume 60x data bus ownership as long as it senses DBB asserted by an external 60x bus
master.
IRQ3
Interrupt request 3—This input is one of the eight external lines that can request (by means of the
internal interrupt controller) a service routine from the core.
D[0–63]
60x data bus—These are input/output pins. In write transactions the 60x bus master drives the
valid data on this bus. In read transactions the 60x slave drives the valid data on this bus.
DP[0]
60x data parity 0—(Input/output) The 60x agent that drives the data bus drives also the data parity
signals. The value driven on data parity 0 pin should give odd parity (odd number of 1’s) on the
group of signals that includes data parity 0 and D[0–7].
RSRV
Reservation—The value driven on this output pin represents the state of the coherency bit in the
reservation address register that is used by the lwarx and stwcx. instructions.
EXT_BR2
External bus request 2—(Input). An external master should assert this pin to request 60x bus
ownership from the internal arbiter.
IRQ1
Interrupt request 1—This input is one of the eight external lines that can request (by means of the
internal interrupt controller) a service routine from the core.
DP[1]
60x data parity 1—(Input/output) The 60x agent that drives the data bus drives also the data parity
signals. The value driven on data parity 1 pin should give odd parity (odd number of ‘1’s) on the
group of signals that includes data parity 1 and D[8–15].
EXT_BG2
External bus grant 2—(Output) The MPC8280 asserts this pin to grant 60x bus ownership to an
external bus master.
IRQ2
Interrupt request 2—This input is one of the eight external lines that can request (by means of the
internal interrupt controller) a service routine from the core.
DP[2]
60x data parity 2—(Input/output) The 60x agent that drives the data bus drives also the data parity
signals. The value driven on data parity 2 pin should give odd parity (odd number of ‘1’s) on the
group of signals that includes data parity 2 and S[16–23].
TLBISYNC
TLB sync—This input pin can be used to synchronize 60x core instruction execution to hardware
indications. Asserting this pin will force the core to stop instruction execution following a tlbsync
instruction execution. The core resumes instructions execution once this pin is negated.
EXT_DBG2
External data bus grant 2—(Output) The MPC8280 asserts this pin to grant 60x data bus
ownership to an external bus master.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
6-4
Freescale Semiconductor
External Signals
Table 6-1. External Signals (continued)
Signal
Description
IRQ3
Interrupt request 3—This input is one of the eight external lines that can request (by means of the
internal interrupt controller) a service routine from the core.
DP[3]
60x data parity 3—(Input/output) The 60x agent that drives the data bus drives also the data parity
signals. The value driven on data parity 3 pin should give odd parity (odd number of 1’s) on the
group of signals that includes data parity 3 and D[24–31].
CKSTP_OUT
Checkstop output—(Output) Assertion indicates that the core is in its checkstop mode.
EXT_BR3
External bus request 3—(Input) An external master should assert this pin to request 60x bus
ownership from the internal arbiter.
IRQ4
Interrupt request 4—This input is one of the eight external lines that can request (by means of the
internal interrupt controller) a service routine from the core.
DP[4]
60x data parity 4—(Input/output) The 60x agent that drives the data bus drives also the data parity
signals. The value driven on data parity 4 pin should give odd parity (odd number of ‘1’s) on the
group of signals that includes data parity 4 and D[32–39].
CORE_SRESET
Core system reset—(Input) Asserting this pin will force the core to branch to its reset vector.
EXT_BG3
External bus grant 3—(Output) The MPC8280 asserts this pin to grant 60x bus ownership to an
external bus master.
IRQ5
Interrupt request 5—This input is one of the eight external lines that can request (by means of the
internal interrupt controller) a service routine from the core.
DP[5]
60x data parity 5—(Input/output) The 60x agent that drives the data bus drives also the data parity
signals. The value driven on data parity 5 pin should give odd parity (odd number of ‘1’s) on the
group of signals that includes data parity 5 and D[40–47].
TBEN
Time base enable—This is a count enable input to the Time Base counter in the core.
EXT_DBG3
External data bus grant 3—(Output) The MPC8280 asserts this pin to grant 60x data bus
ownership to an external bus master.
CINT
Critical interrupt—Critical interrupt input to the core
IRQ6
Interrupt request 6—This input is one of the eight external lines that can request (by means of the
internal interrupt controller) a service routine from the core.
DP[6]
60x data parity 6—(Input/output) The 60x agent that drives the data bus drives also the data parity
signals. The value driven on data parity 6 pin should give odd parity (odd number of ‘1’s) on the
group of signals that includes data parity 6 and D[48–55].
CSE[0]
Cache set entry 0—The cache set entry outputs from the core represent the cache replacement
set element for the current core transaction reloading into or writing out of the cache.
IRQ7
Interrupt request 7—This input is one of the eight external lines that can request (by means of the
internal interrupt controller) a service routine from the core.
DP[7]
60x data parity 7—(Input/output) The 60x master or slave that drives the data bus drives also the
data parity signals. The value driven on data parity 7 pin should give odd parity (odd number of
‘1’s) on the group of signals that includes data parity 7 and D[56–63].
CSE[1]
Cache set entry 1—The cache set entry outputs from the core represent the cache replacement
set element for the current core transaction reloading into or writing out of the cache.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
6-5
External Signals
Table 6-1. External Signals (continued)
Signal
Description
PSDVAL
60x data valid—(Input/output) Assertion of the PSDVAL pin indicates that a data beat is valid on
the data bus. The difference between the TA pin and the PSDVAL pin is that the TA pin is asserted
to indicate 60x data transfer terminations while the PSDVAL signal is asserted with each data
beat movement. Thus always when TA is asserted, PSDVAL will be asserted but when PSDVAL
is asserted, TA is not necessarily asserted. For example when a double word (2x64 bits) transfer
is initiated by the SDMA to a memory device that has 32 bits port size, PSDVAL will be asserted
3 times without TA and finally both pins will be asserted to terminate the transfer.
TA
Transfer acknowledge—(Input/output) Indicates that a 60x data beat is valid on the data bus. For
60x single beat transfers, assertion of this pin indicates the termination of the transfer. For 60x
burst transfers TA is asserted four times to indicate the transfer of four data beats with the last
assertion indicating the termination of the burst transfer.
TEA
Transfer error acknowledge—(Input/output) Assertion of this pin indicates a bus error. 60x
masters within the MPC8280 monitor the state of this pin. MPC8280’s internal bus monitor may
assert this pin in case it identified a 60x bus transfer that is hung.
GBL
Global—(Input/output) When a 60x master within the chip initiates a bus transaction it drives this
pin. When an external 60x master initiates a bus transaction it should drive this pin. Assertion of
this pin indicates that the transfer is global and it should be snooped by caches in the system. The
MPC8280’s data cache monitors the state of this pin.
IRQ1
Interrupt request 1—This input is one of the eight external lines that can request (by means of the
internal interrupt controller) a service routine from the core.
CI
Cache inhibit—Output pin. Used for L2 cache control. For each MPC8280 60x transaction
initiated in the core, the state of this pin indicates if this transaction should be cached or not.
Assertion of the CI pin indicates that the transaction should not be cached.
BADDR29
Burst address 29—There are five burst address output pins. These pins are outputs of the 60x
memory controller. These pins are used in external master configuration and are connected
directly to memory devices controlled by MPC8280’s memory controller. For information on the
use of this signal, see Section 11.2.14, “BADDR[27:31] Signal Connections.”
IRQ2
Interrupt request 2—This input is one of the eight external lines that can request (by means of the
internal interrupt controller) a service routine from the core.
WT
Write through—Output used for L2 cache control. For each core-initiated MPC8280 60x
transaction, the state of this pin indicates if the transaction should be cached using write-through
or copy-back mode. Assertion of WT indicates that the transaction should be cached using the
write-through mode.
BADDR30
Burst address 30—There are five burst address output pins. These pins are outputs of the 60x
memory controller. These pins are used in external master configuration and are connected
directly to memory devices controlled by MPC8280’s memory controller. For information on the
use of this signal, see Section 11.2.14, “BADDR[27:31] Signal Connections.”
IRQ3
Interrupt request 3—This input is one of the eight external lines that can request (by means of the
internal interrupt controller) a service routine from the core.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
6-6
Freescale Semiconductor
External Signals
Table 6-1. External Signals (continued)
Signal
Description
L2_HIT
L2 cache hit—(Input) It is used for L2 cache control. Assertion of this pin indicates that the 60x
transaction will be handled by the L2 cache. In this case, the memory controller will not start an
access to the memory it controls.
IRQ4
Interrupt request 4—This input is one of the eight external lines that can request (by means of the
internal interrupt controller) a service routine from the core.
CPU_BG
CPU bus grant—(Output) The value of the 60x core bus grant is driven on this pin to be used by
an external MPC2605GA L2 cache. The driven bus grant is not qualified; that is, when using an
external arbiter, the user should qualify this signal with the bus grant input to the MPC8280 before
connecting it to the L2 cache.
BADDR31
Burst address 31—There are five burst address output of the 60x memory controller used in an
external master configuration and are connected directly to the memory devices controlled by
MPC8280’s memory controller. For information on the use of this signal, see Section 11.2.14,
“BADDR[27:31] Signal Connections.”
IRQ5
Interrupt Request 5—This input is one of the eight external lines that can request (by means of
the internal interrupt controller) a service routine from the core.
CINT
Critical interrupt—Critical interrupt input to the core
CPU_DBG
CPU data bus grant—(Output) Valid only when using the internal arbiter (PPC_ACR[EARB] = 0).
The OR of all data bus grant signals for internal masters from the internal arbiter is driven on
CPU_DBG. CPU_DBG should be connected to the CPU DBG input of an external MPC2605GA
L2 cache. (If an external arbiter is used, the CPU DBG input of the external MPC2605GA L2
cache should be connected to the DBG driven from the external arbiter to this MPC8280.)
CPU_BR
CPU bus request—(Output) The value of the 60x core bus request is driven on this pin for the use
of an external L2 cache.
CS[0–9]
Chip select—These are output pins that enable specific memory devices or peripherals
connected to MPC8280 buses.
CS[10]
Chip select—These are output pins that enable specific memory devices or peripherals
connected to MPC8280 buses.
BCTL1
Buffer control 1—Output signal whose function is controlling buffers on the 60x data bus. Usually
used with BCTL0. The exact function of this pin is defined by the value of SIUMCR[BCTLC]. See
Section 4.3.2.6, “SIU Module Configuration Register (SIUMCR),” for details.
CS[11]
Chip select—Output that enable specific memory devices or peripherals connected to MPC8280
buses.
AP[0]
Address parity 0—(Input/output) The 60x master that drives the address bus, drives also the
address parity signals. The value driven on address parity 0 pin should give odd parity (odd
number of ‘1’s) on the group of signals that includes address parity 0 and A[0–7].
BADDR[27–28]
Burst address 27–28—There are five burst address output pins. These pins are outputs of the
60x memory controller. Used in external master configuration and connected directly to the
memory devices controlled by MPC8280’s memory controller. For information on the use of these
signals, see Section 11.2.14, “BADDR[27:31] Signal Connections.”
ALE
Address latch enable—This output pin controls the external address latch that should be used in
external master 60x bus configuration.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
6-7
External Signals
Table 6-1. External Signals (continued)
Signal
Description
BCTL0
Buffer control 0—Output whose function is controlling buffers on the 60x data bus. Usually used
with BCTL1 that is multiplexed on CS10. The exact function of this pin is defined by the value of
SIUMCR[BCTLC]. See Section 4.3.2.6, “SIU Module Configuration Register (SIUMCR),” for
details.
PWE[0–7]
60x bus write enable—Outputs of the 60x bus GPCM. These pins select byte lanes for write
operations.
PSDDQM[0–7]
60x bus SDRAM DQM—The DQM pins are outputs of the SDRAM control machine. These pins
select specific byte lanes of SDRAM devices.
PBS[0–7]
60x bus UPM byte select—The byte select pins are outputs of the UPM in the memory controller.
They are used to select specific byte lanes during memory operations. The timing of these pins
is programmed in the UPM. The actual driven value depends on the address and size of the
transaction and the port size of the accessed device.
PSDA10
60x bus SDRAM A10—(Output) from the 60x bus SDRAM controller. Part of the address when a
row address is driven and is part of the command when a column address is driven.
PGPL0
60x bus UPM general purpose line 0—One of six general purpose output lines from UPM. The
values and timing of this pin is programmed in the UPM.
PSDWE
60x bus SDRAM write enable—(Output) from the 60x bus SDRAM controller. Should be
connected to SDRAMs’ WE input.
PGPL1
60x bus UPM general purpose line 1—One of six general purpose output lines from UPM. The
values and timing of this pin is programmed in the UPM.
POE
60x bus output enable—The output enable pin is an output of the 60x bus GPCM. Controls the
output buffer of memory devices during read operations.
PSDRAS
60x bus SDRAM ras—Output from the 60x bus SDRAM controller. Should be connected to
SDRAMs’ RAS input.
PGPL2
60x bus UPM general purpose line 2—One of six general purpose output lines from UPM. The
values and timing of this pin is programmed in the UPM.
PSDCAS
60x bus SDRAM CAS—Output from the 60x bus SDRAM controller. Should be connected to
SDRAMs’ CAS input.
PGPL3
60x bus UPM general purpose line 3—One of six general purpose output lines from UPM. The
values and timing of this pin is programmed in the UPM.
PGTA
60x GPCM TA—This input pin is used for transaction termination during GPCM operation.
Requires external pull up resistor for proper operation.
PUPMWAIT
60x bus UPM wait—This is an input to the UPM. An external device may hold this pin high to force
the UPM to wait until the device is ready for the continuation of the operation.
PGPL4
60x bus UPM general purpose line 4—One of six general purpose output lines from UPM. The
values and timing of this pin is programmed in the UPM.
PPBS
60x bus parity byte select—In systems in which data parity is stored in a separate chip, this output
is used as the byte-select for that chip.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
6-8
Freescale Semiconductor
External Signals
Table 6-1. External Signals (continued)
Signal
PSDAMUX
Description
60x bus SDRAM address multiplexer—This output pin controls the 60x SDRAM address
multiplexer when the MPC8280 is in external master mode.
PGPL5
60x bus UPM general purpose line 5—One of six general purpose output lines from UPM. The
values and timing of this pin is programmed in the UPM.
LWE[0–3]
Local bus write enable—The write enable pins are outputs of the Local bus GPCM. These pins
select specific byte lanes for write operations.
LSDDQM[0–3]
Local bus SDRAM DQM—The DQM pins are outputs of the SDRAM control machine. These pins
select specific byte lanes of SDRAM devices.
LBS[0–3]
Local bus UPM byte select—The byte select pins are outputs of the UPM in the memory
controller. They are used to select specific byte lanes during memory operations. The timing of
these pins is programmed in the UPM. The actual driven value depends on the address and size
of the transaction and the port size of the accessed device.
PCI_CFG[0-3]
PCI Configuration—In PCI mode, PCI_CFG[0-3] configure the PCI bridge to Host or agent and
control the PCI arbiter operation:
• PCI_CFG[0] is PCI_HOST, when High enables the PCI bridge for Agent operation, when Low
enables the PCI as Host.
• PCI_CFG[1] is PCI_ARB_EN, when Low enables the PCI internal arbiter logic, when High
disables the internal arbiter logic (and an external arbiter should be used).
• PCI_CFG[2] is the DLL_Enable. In PCI mode, this pin should be pulled high externally in order
to use the DLL.
• PCI_CFG[3] is reserved and should be pulled high externally.
LSDA10
Local bus SDRAM A10—Output from the 60x bus SDRAM controller. Is part of the address when
a row address is driven and is part of the command when a column address is driven.
LGPL0
Local bus UPM general purpose line 0—This is one of six general purpose output lines from
UPM. The values and timing of this pin is programmed in the UPM.
PCI_MODCK_H0
PCI MODCK_H0—In PCI mode, defines the operating mode of internal clock circuits.
LSDWE
Local bus SDRAM write enable—Output from the local bus SDRAM controller. Should be
connected to the WE inputs of the SDRAMs.
LGPL1
Local bus UPM general purpose line 1—This is one of six general purpose output lines from
UPM. The values and timing of this pin is programmed in the UPM.
PCI_MODCK_H1
PCI MODCK_H1—In PCI mode, defines the operating mode of internal clock circuits.
LOE
Local bus output enable—The output enable pin is an output of the Local bus GPCM. Controls
the output buffer of memory devices during read operations.
LSDRAS
Local bus SDRAM RAS—Output from the Local bus SDRAM controller. Should be connected to
the SDRAM RAS input.
LGPL2
Local bus UPM general purpose line 2—This is one of six general purpose output lines from
UPM. The values and timing of this pin is programmed in the UPM.
PCI_MODCK_H2
PCI MODCK_H2—In PCI mode, defines the operating mode of internal clock circuits.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
6-9
External Signals
Table 6-1. External Signals (continued)
Signal
Description
LSDCAS
Local bus SDRAM CAS—Output from the Local bus SDRAM controller. Should be connected to
the CAS inputs of the SDRAMs.
LGPL3
Local bus UPM general purpose line 3—This is one of six general purpose output lines from
UPM. The values and timing of this pin is programmed in the UPM.
PCI_MODCK_H3
PCI MODCK_H3—In PCI mode, defines the operating mode of internal clock circuits.
LGTA
Local bus GPCM TA—This input pin is used for transaction termination during GPCM operation.
Requires external pull up resistor for proper operation.
LUPMWAIT
Local bus UPM wait—This is an input to the UPM. An external device may hold this pin high to
force the UPM to wait until the device is ready for the continuation of the operation.
LGPL4
Local bus UPM general purpose line 4—One of six general purpose output lines from UPM. The
values and timing of this pin is programmed in the UPM.
LPBS
Local bus parity byte select—In systems in which the data parity is stored in a separate chip, this
output is used as the byte select for that chip.
LGPL5
Local bus UPM general purpose line 5—This is one of six general purpose output lines from
UPM. The values and timing of this pin is programmed in the UPM.
PCI_MODCK
PCI MODCK—In PCI mode, defines additional operating modes of internal clock circuits.
LWR
Local write—The local write pin is an output from the local bus memory controller. It is used to
distinguish between read and write transactions.
L_A14
Local bus address 14—Local bus address bit 14 output pin. In the local address bus bit 14 is most
significant and bit 31 is least significant.
PCI_PAR
PCI parity—PCI parity input/output pin. Assertion of this pin indicates that odd parity is driven
across PCI_AD[31-0] and PCI_C/BE[3–0] during address and data phases. Negation of
PCI_PAR indicates that even parity is driven across the PCI_AD[31-0] and PCI_C/BE[3–0] during
address and data phases.
L_A15
Local bus address 15—Local bus address bit 15 output pin. In the local address bus bit 14 is most
significant and bit 31 is least significant.
SMI
System management interrupt—System management interrupt input to the core.
PCI_FRAME
PCI frame—PCI cycle frame input/output pin. Used by the current PCI master to indicate the
beginning and duration of an access. Driven by the MPC8280 when its PCI interface is the master
of the access. Otherwise, it is an input.
L_A16
Local bus address 16—Local bus address bit 16 output pin. In the local address bus bit 14 is most
significant and bit 31 is least significant.
PCI_TRDY
PCI target ready—PCI target ready input/output pin. This pin is driven by the MPC8280 when its
PCI interface is the target of a PCI transfer. Assertion of this pin indicates that the PCI target is
ready to send or accept a data beat.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
6-10
Freescale Semiconductor
External Signals
Table 6-1. External Signals (continued)
Signal
Description
L_A17
Local bus address 17—Local bus address bit 17 output pin. In the local address bus bit 14 is most
significant and bit 31 is least significant.
PCI_IRDY
PCI initiator ready—PCI initiator ready input/output pin. This pin is driven by the MPC8280 when
its PCI interface is the initiator of a PCI transfer. Assertion of this pin indicates that the PCI initiator
is ready to send or accept a data beat.
CKSTOP_OUT
Checkstop output—(Output) Assertion of CKSTOP_OUT indicates the core is in checkstop
mode.
L_A18
Local bus address 18—Local bus address bit 18 output pin. In the local address bus bit 14 is most
significant and bit 31 is least significant.
PCI_STOP
PCI stop—PCI stop input/output pin. This pin is driven by the MPC8280 when its PCI interface is
the target of a PCI transfer. Assertion of this pin indicates that the PCI target is requesting the
master to stop the current PCI transfer.
L_A19
Local bus address 19—Local bus address bit 19 output pin. In the local address bus bit 14 is most
significant and bit 31 is least significant.
PCI_DEVSEL
PCI device select—PCI device select input/output pin. This pin is driven by the MPC8280 when
its PCI interface has decoded its own address as the target of the current PCI transfer. As an
input, PCI_DEVSEL indicates whether any device on the PCI bus has been selected.
L_A20
Local bus address 20—Local bus address bit 20 output pin. In the local address bus bit 14 is most
significant and bit 31 is least significant.
PCI_IDSEL
PCI initialization device select—(Input) Used to select the MPC8280’s PCI interface during a PCI
configuration cycle.
L_A21
Local bus address 21—Local bus address bit 21 output pin. In the local address bus bit 14 is most
significant and bit 31 is least significant.
PCI_PERR
PCI parity error—PCI data parity error input/output pin. Assertion of this pin indicates that a data
parity error was detected during a PCI transfer (except for a special cycle).
L_A22
Local bus address 22—Local bus address bit 22 output pin. In the local address bus bit 14 is most
significant and bit 31 is least significant.
PCI_SERR
PCI system error—PCI system error input/output pin. Assertion of this pin indicates that a PCI
system error was detected during a PCI transfer. The PCI system error is for reporting address
parity errors, data parity errors on a special cycle command, or other catastrophic system errors.
L_A23
Local bus address 23—Local bus address bit 23 output pin. In the local address bus bit 14 is most
significant and bit 31 is least significant.
PCI_REQ0
PCI arbiter request 0—PCI request 0 input/output pin. When the MPC8280’s internal PCI arbiter
is used, this is an input pin. In this mode assertion of this pin indicates that an external PCI device
is requesting the PCI bus. When an external PCI arbiter is used, this is an output pin. In this mode
assertion of this pin indicates that the MPC8280’s PCI interface is requesting the PCI bus.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
6-11
External Signals
Table 6-1. External Signals (continued)
Signal
Description
L_A24
Local bus address 24—Local bus address bit 24 output pin. In the local address bus bit 14 is most
significant and bit 31 is least significant.
PCI_REQ1
PCI arbiter request 1—PCI request 1 input pin. When the MPC8280’s internal PCI arbiter is used,
assertion of this pin indicates that an external PCI device is requesting the PCI bus.
CPCI_HS_ES
CompactPCI Hot Swap Ejector Switch—Hot Swap Ejector Switch input pin. In a CompactPCI
system, when the MPC8280’s internal PCI arbiter is not used, this pin is used for the Hot Swap
interface to connect to the ejector switch logic.
0 Switch is closed
1 Switch is open
Important note: When functioning as the CPCI_HS_ES input, this signal must be filtered
(debounced) by an external circuit. Do not connect this input directly to the ejector switch. The
input must be a monotonically rising/falling signal.
L_A25
Local bus address 25—Local bus address bit 25 output pin. In the local address bus bit 14 is most
significant and bit 31 is least significant.
PCI_GNT0
PCI arbiter grant 0—PCI grant 0 input/output pin. When the MPC8280’s internal PCI arbiter is
used, this is an output pin. In this mode, assertion of PCI_GNT0 indicates that an the external
PCI device that requested the PCI bus with PCI_REQ0 is granted the bus. When an external PCI
arbiter is used, this is an input pin. In this mode, assertion of PCI_GNT0 indicates that the
MPC8280’s PCI interface is granted the PCI bus.
L_A26
Local bus address 26—Local bus address bit 26 output pin. In the local address bus bit 14 is most
significant and bit 31 is least significant.
PCI_GNT1
PCI arbiter grant 1—PCI grant 1 output pin. When the MPC8280’s internal PCI arbiter is used,
assertion of PCI_GNT1 indicates that the external PCI device that requested the PCI bus with
PCI_REQ1 pin is granted the bus.
CPCI_HS_LED
CompactPCI Hot Swap LED—Hot Swap LED output pin. In CompactPCI system, when the
MPC8280’s internal PCI arbiter is not used, this pin is used for the Hot Swap interface to connect
to the Hot Swap LED. The Hot Swap pins are not available when the internal arbiter is used.
0 LED is off
1 LED is on
L_A27
Local bus address 27—Local bus address bit 27 output pin. In the local address bus bit 14 is most
significant and bit 31 is least significant.
PCI_GNT2
PCI arbiter grant 2—PCI grant 2 output pin. When the MPC8280’s internal PCI arbiter is used,
assertion of PCI_GNT2 indicates that the external PCI device that requested the PCI bus with
PCI_REQ2 pin is granted the bus.
CPCI_HS_ENUM
CompactPCI Hot Swap Enumerator—Hot Swap ENUM output pin. In CompactPCI system, when
the MPC8280’s internal PCI arbiter is not used, this pin is used for the Hot Swap interface to
connect to the host as the enumeration request.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
6-12
Freescale Semiconductor
External Signals
Table 6-1. External Signals (continued)
Signal
Description
L_A28
Local bus address 28—Local bus address bit 28 output pin. In the local address bus bit 14 is most
significant and bit 31 is least significant.
PCI_RST
PCI reset—PCI reset output pin. When the MPC8280 is the host in the PCI system, PCI_RST is
an output.
CORE_SRESET
Core system reset—This is an input to the core. When this input pin is asserted the core branches
to its reset vector.
L_A29
Local bus address 29—Local bus address bit 29 output pin. In the local address bus bit 14 is most
significant and bit 31 is least significant.
PCI_INTA
PCI INTA—(output) When the MPC8280 is an agent of the PCI system, this pin is an output used
by the MPC8280 to signal an interrupt to the PCI host. (When the MPC8280 is the host in the PCI
system, the general IRQ pins are used for delivering PCI interrupts to the host.)
L_A30
Local bus address 30—Local bus address bit 30 output pin. In the local address bus bit 14 is most
significant and bit 31 is least significant.
PCI_REQ2
PCI arbiter request 2—PCI request 2 input pin. When the MPC8280’s internal PCI arbiter is used,
assertion of this pin indicates that an external PCI device is requesting the PCI bus.
L_A31
Local bus address 31—Local bus address bit 31 output pin. In the local address bus bit 14 is most
significant and bit 31 is least significant.
DLLOUT
DLL Clock Out—DLL output pin. This is the DLL output reference clock. See Figure 10-2 and
Figure 10-3.
LCL_D[0–31]
Local bus data—Local bus data input/output pins. In the local data bus bit 0 is most significant
and bit 31 is least significant.
PCI_AD[31-0]
PCI address/data—PCI bus address/data input/output pins. During an address phase
PCI_AD[31-0] contains a physical address, during a data phase PCI_AD[31-0] contains the data
bytes. In the PCI address/data bus, bit 31 is msb and bit 0 is lsb.
LCL_DP[0–3]
Local bus data parity—Local bus data parity input/output pins. In local bus write operations the
MPC8280 drives these pins. In local bus read operations the accessed device drives these pins.
LCL_DP[0] is driven with a value that gives odd parity with LCL_D[0–7]. LCL_DP[1] is driven with
a value that gives odd parity with LCL_D[8–15]. LCL_DP[2] is driven with a value that gives odd
parity with LCL_D[16–23]. LCL_DP[3] is driven with a value that gives odd parity with
LCL_D[24–31].
PCI_C/BE[3-0]
PCI command/byte enable—PCI command/byte enable input/output pins. The MPC8280 drives
these pins when it is the initiator of a PCI transfer. During an address phase the PCI_C/BE[3-0]
defines the command, during the data phase PCI_C/BE[3-0] defines the byte enables.
PCI_C/BE[3] is the msb and PCI_C/BE[0] is the lsb.
IRQ0
Interrupt request 0—This input is an external line that causes an MCP interrupt to the core.
NMI_OUT
Non-maskable interrupt output—This is an output driven from MPC8280’s internal interrupt
controller. Assertion of this output indicates that a non-maskable interrupt is pending in
MPC8280’s internal interrupt controller.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
6-13
External Signals
Table 6-1. External Signals (continued)
Signal
Description
IRQ7
Interrupt request 7—This input is one of the eight external lines that can request (by means of the
internal interrupt controller) a service routine from the core.
INT_OUT
Interrupt output—This is an output driven from MPC8280’s internal interrupt controller. Assertion
of this output indicates that an unmasked interrupt is pending in MPC8280’s internal interrupt
controller.
APE
Address parity error—This output pin is asserted when the MPC8280 detects wrong parity driven
on its address parity pins by an external master.
TRST
Test reset (JTAG)— Input only. This is the reset input to the MPC8280’s JTAG/COP controller. See
Section 13.1, “Overview,” and Section 13.6, “Nonscan Chain Operation.”
TCK
Test clock (JTAG)—Input only. Provides the clock input for MPC8280’s JTAG/COP controller.
TMS
Test mode select (JTAG)—Input only. Controls the state of MPC8280’s JTAG/COP controller.
TDI
Test data in (JTAG)—Input only. Data input to MPC8280’s JTAG/COP controller.
TDO
Test data out (JTAG)—Output only. Data output from MPC8280’s JTAG/COP controller.
TRIS
Three-state—Asserting TRIS forces all other MPC8280’s pins to high impedance state.
PORESET
Power-on reset—When asserted, this input line causes the MPC8280 to enter power-on reset
state.
PCI_RST
PCI reset—PCI reset input pin. When the MPC8280 is an agent in the PCI system, PCI_RST is
an input.
HRESET
Hard reset—This open drain line, when asserted causes the MPC8280 to enter hard reset state.
SRESET
Soft reset—This open drain line, when asserted causes the MPC8280 to enter the soft reset
state.
QREQ
Quiescent request— Output only. Indicates that MPC8280’s internal core is about to enter its low
power mode. In the MPC8280 this pin will be typically used for debug purposes.
RSTCONF
RSTCONF —Input used during reset configuration sequence of the chip. Find detailed
explanation of its function in Section 5.1.2, “Power-On Reset Flow,” and Section 5.4, “Reset
Configuration.”
MODCK1
MODCK1—Clock mode input. Defines the operating mode of internal clock circuits.
AP[1]
Address parity 1—(Input/output) The 60x master that drives the address bus, drives also the
address parity signals. The value driven on address parity 1 pin should give odd parity (odd
number of 1s) on the group of signals that includes address parity 1 and A[8–15].
TC[0]
Transfer Code 0—The transfer code output pins supply information that can be useful for debug
purposes for each of the MPC8280’s initiated bus transactions.
BNKSEL[0]
Bank Select 0—The bank select outputs are used for selecting SDRAM bank when the MPC8280
is in 60x compatible bus mode. BNKSEL0 is msb of the three BNKSEL signals.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
6-14
Freescale Semiconductor
External Signals
Table 6-1. External Signals (continued)
Signal
Description
MODCK2
MODCK2—Clock mode input. Defines the operating mode of internal clock circuits.
AP[2]
Address parity 2—(Input/output) The 60x master that drives the address bus, drives also the
address parity signals. The value driven on address parity 2 pin should give odd parity (odd
number of 1s) on the group of signals that includes address parity 2 and A[16–23].
TC[1]
Transfer code 1—The transfer code output pins supply information that can be useful for debug
purposes for each of the MPC8280’s initiated bus transactions.
BNKSEL[1]
Bank select 1—The bank select outputs are used for selecting SDRAM bank when the MPC8280
is in 60x-compatible bus mode.
MODCK3
MODCK3—Clock mode input. Defines the operating mode of internal clock circuits.
AP[3]
Address parity 3—(Input/output) The 60x master that drives the address bus, drives also the
address parity signals. The value driven on address parity 3 pin should give odd parity (odd
number of 1s) on the group of signals that includes address parity 3 and A[24—31].
TC[2]
Transfer code 2—The transfer code output pins supply information that can be useful for debug
purposes for each of the MPC8280’s initiated bus transactions.
BNKSEL[2]
Bank select 2—The bank select outputs are used for selecting SDRAM bank when the MPC8280
is in 60x-compatible bus mode. BNKSEL2 is lsb of the three BNKSEL signals.
XFC
External filter capacitance—Input connection for an external capacitor filter for PLL circuitry.
CLKIN1
Clock In—Primary clock input to MPC8280’s PLL. In a PCI system, where the MPC8280 PCI
interface is operated from the PCI bus clock, CLKIN should be connected to the PCI bus clock.
In that case, the 60x bus clock is driven on CLKOUT. See Figure 10-2 and Figure 10-3.
CLKIN2
Clock In2—This is the clock input to the MPC8280’s DLL, which is used for deskewing the output
reference clock. See Figure 10-2 and Figure 10-3.
PCI_MODE
PCI mode pin—This pin enables the PCI bridge of the MPC8280.
• When Low, the PCI bridge is enabled, PCI interface replaces the Local bus.
• When High, the PCI bridge is disabled, the MPC8280 operates with the Local bus.
This pin has an internal pull up resistor so it defaults to Local bus operation.
PA[0–31]
General-purpose I/O port A bits 0–31—CPM port multiplexing is described in Chapter 41,
“Parallel I/O Ports.”
PB[4–31]
General-purpose I/O port B bits 4–31—CPM port multiplexing is described in Chapter 41,
“Parallel I/O Ports.”
PC[0–31]
General-purpose I/O port C bits 0–31—CPM port multiplexing is described in Chapter 41,
“Parallel I/O Ports.”
PD[4–31]
General-purpose I/O port D bits 4–31—CPM port multiplexing is described in Chapter 41,
“Parallel I/O Ports.”
Power Supply
VDD—This is the power supply of the internal logic.
VDDH—This is the power supply of the I/O Buffers.
VCCSYN—This is the power supply of the PLL circuitry.
GNDSYN—This is a special ground of the PLL circuitry.
VCCSYN1—This is the power supply of the core’s PLL circuitry.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
6-15
External Signals
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
6-16
Freescale Semiconductor
Chapter 7
60x Signals
This chapter describes the MPC8280 processor’s external signals. It contains a concise description of
individual signals, showing behavior when a signal is asserted and negated, when the signal is an input and
an output, and the differences in how signals work in external-master or internal-only configurations.
NOTE
A bar over a signal name indicates that the signal is active low– for example,
ARTRY (address retry) and TS (transfer start). Active-low signals are
referred to as asserted (active) when they are low and negated when they are
high. Signals that are not active-low, such as TSIZ[0–3] (transfer size
signals) and TT[0–4] (transfer type signals) are referred to as asserted when
they are high and negated when they are low.
The 60x bus signals used with MPC8280 are grouped as follows:
• Address arbitration signals—In external arbiter mode, MPC8280 uses these signals to arbitrate for
address bus mastership. The MPC8280 arbiter uses these signals to enable an external device to
arbitrate for address bus mastership.
• Address transfer start signals—These signals indicate that a bus master has begun a transaction on
the address bus.
• Address transfer signals (address bus)—These signals are used to transfer the address.
• Transfer attribute signals—These signals provide information about the type of transfer, such as
the transfer size and whether the transaction is single, single extended, bursted, write-through or
cache-inhibited.
• Address transfer termination signals—These signals are used to acknowledge the end of the
address phase of the transaction. They also indicate whether a condition exists that requires the
address phase to be repeated.
• Data arbitration signals—The MPC8280, in external arbiter mode, uses these signals to arbitrate
for data bus mastership. The MPC8280 arbiter uses these signals to enable an external device to
arbitrate for data bus mastership.
• Data transfer signals—These signals, which consist of the data bus, data parity, and data parity
error signals, transfer the data and ensure its integrity.
• Data transfer termination signals—Data termination signals are required after each data beat in a
data transfer. In a single-beat transaction, the data termination signals also indicate the end of the
tenure. For burst accesses or extended port-size accesses, the data termination signals apply to
individual beats and indicate the end of the tenure only after the final data beat.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
7-1
60x Signals
7.1
Signal Configuration
Figure 7-1 shows the 60x bus signal configuration grouping of the MPC8280.
NOTE
The MPC8280 hardware specifications provide a pinout showing numbers
of pins. These are shown in Figure 7-1.
Bus Request (BR)
Address
Arbitration
Bus Grant (BG)
Address Bus Busy (ABB)
Address
Start
Transfer Start (TS)
Address (A[0–31])
Address
Bus
Address Parity (AP[0–3])
Address Parity Error (APE)
Transfer Type (TT[0–4])
Transfer Code (TC[0–2])
Transfer
Attributes
Address
Termination
1
Data Bus Grant (DBG)
1
1
Data
Arbitration
1
Data Bus Busy (DBB)
1
64
32
Data (D[0–63])
Data
Transfer
8
Data Parity (DP[0–7])
1
Partial Data Valid Indication (PSDVAL)
1
Transfer Acknowledge (TA)
1
Transfer Error Acknowledge (TEA)
4
1
5
3
Transfer Burst (TBST)
1
Transfer Size (TSIZ[0–3])
4
Global (GBL)
1
Data
Termination
1
Cache Inhibit (CI)
1
Write-Through (WT)
1
Address Acknowledge (AACK)
1
1
Reservation
Address Retry (ARTRY)
1
1
TLBISYNC
Processor
State
Figure 7-1. Signal Groupings
7.2
Signal Descriptions
This section describes individual MPC8280 60x signals, grouped according to Figure 7-1. Note that the
following sections briefly summarize signal functions. Chapter 8, “The 60x Bus,” describes many of these
signals in greater detail, both in terms of their function and how groups of signals interact.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
7-2
Freescale Semiconductor
60x Signals
7.2.1
Address Bus Arbitration Signals
The address arbitration signals are a collection of input and output signals devices use to request address
bus mastership, recognize when the request is granted, and indicate to other devices when mastership is
granted. For a detailed description of how these signals interact, see Section 8.4.1, “Address Arbitration.”
Bus arbitration signals have no meaning in internal-only mode.
7.2.1.1
Bus Request (BR)—Output
The bus request (BR) signal is both an input and an output signal on the MPC8280.
7.2.1.1.1
Address Bus Request (BR)—Output
Following are the state meaning and timing comments for the BR signal output.
State Meaning
Asserted—Indicates that MPC8280 is requesting mastership of the address bus.
Note that BR may be asserted for one or more cycles and then deasserted due to
an internal cancellation of the bus request (for example, due to a load hit in the
touch load buffer). See Section 8.4.1, “Address Arbitration.”
Negated—Indicates that the MPC8280 is not requesting the address bus. The
MPC8280 may have no bus operation pending, it may be parked, or the ARTRY
input was asserted on the previous bus clock cycle.
Timing Comments
Assertion—May occur on any cycle; does not occur if the MPC8280 is parked and
the address bus is idle (BG asserted and ABB input negated).
Negation—Occurs for at least one cycle following a qualified BG even if another
transaction is pending; also negated for at least one cycle following any qualified
ARTRY on the bus unless MPC8280 asserted ARTRY and requires a snoop
copyback; may also be negated if MPC8280 cancels the bus request internally
before receiving a qualified BG.
High Impedance—Occurs during a hard reset or checkstop condition
7.2.1.1.2
Address Bus Request (BR)—Input
Following are the state meaning and timing comments for the BR signal input.
State Meaning
Asserted—Indicates that the external master has a bus transaction to perform and
is waiting for a qualified BG to begin the address tenure. BR may be asserted even
if the two possible pipelined address tenures have already been granted.
Negated—Indicates that the external master has no bus transaction to perform, or
if the device is parked, that it is potentially ready to start a bus transaction on the
next clock cycle (with proper qualification, see BG).
Timing Comments
Assertion—May occur on any cycle; does not occur if the external master is
parked and the address bus is idle (BG asserted and ABB input negated).
Negation—Occurs for at least one cycle after a qualified BG even if another
transaction is pending; also negated for at least one cycle following any qualified
ARTRY on the bus unless this chip asserted the ARTRY and requires to perform
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
7-3
60x Signals
a snoop copyback; may also be negated if the external master cancels a bus request
internally before receiving a qualified BG.
High Impedance—Occurs during a hard reset or checkstop condition.
7.2.1.2
Bus Grant (BG)
The address bus grant (BG) signal is both an input and an output signal.
7.2.1.2.1
Bus Grant (BG)—Input
The following are the state meaning and timing comments for the BG signal input.
State Meaning
Asserted—Indicates that the MPC8280 may, with the proper qualification, begin
a bus transaction and assume ownership of the address bus. A qualified bus grant
is generally determined from the bus state as follows: QBG = BG • ¬ABB •
¬ARTRY where ARTRY is asserted only during the cycle after AACK. Note that
the assertion of BR is not required for a qualified bus grant (for bus parking).
Negated—Indicates that the MPC8280 is not granted next address ownership.
Timing Comments
Assertion—May occur on any cycle. Once the MPC8280 has assumed address bus
ownership, it does not begin checking for BG again until the cycle after AACK.
Negation—May occur whenever the MPC8280 must be prevented from using the
address bus. The MPC8280 may still assume address bus ownership on the cycle
BG is negated if it was asserted the previous cycle with other bus grant
qualifications.
7.2.1.2.2
Bus Grant (BG)—Output
Following are the state meaning and timing comments for the BG signal output.
State Meaning
Asserted—Indicates that the external device may, with the proper qualification,
begin a bus transaction and assume ownership of the address bus. A qualified bus
grant is generally determined from the bus state as follows: QBG = BG • ¬ABB
• ¬ARTRY where ARTRY is asserted only during the cycle after AACK. Note that
the assertion of BR is not required for a qualified bus grant (for bus parking).
Negated—Indicates that the external device is not granted next address
ownership.
Timing Comments
Assertion—May occur on any cycle. Once the external device has assumed
address bus ownership, it does not begin checking for BG again until the cycle
after AACK.
Negation—May occur when an external device must be kept from using the
address bus. The external device may still assume address bus ownership on the
cycle that BG is negated if it was asserted the previous cycle with other bus grant
qualifications.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
7-4
Freescale Semiconductor
60x Signals
7.2.1.3
Address Bus Busy (ABB)
The address bus busy (ABB) signal is both an input and an output signal.
7.2.1.3.1
Address Bus Busy (ABB)—Output
Following are the state meaning and timing comments for the ABB output signal.
State Meaning
Asserted—Indicates that the MPC8280 is the current address bus master. The
MPC8280 may not assume address bus ownership in case a bus request is
internally cancelled by the cycle a qualified BG would have been recognized.
Negated—Indicates that MPC8280 is not the current address bus master.
Timing Comments
Assertion—Occurs the cycle after a qualified BG is accepted by MPC8280 and
remains asserted for the duration of the address tenure.
Turn-Off Sequencing—Negates for a fraction of a bus cycle (1/2 minimum,
depends on clock mode) starting the cycle following the assertion of AACK. It
then goes to the high impedance state.
7.2.1.3.2
Address Bus Busy (ABB)—Input
Following are the state meaning and timing comments for the ABB input signal.
State Meaning
Timing Comments
7.2.2
Asserted—Indicates that external device is the address bus master.
Negated—Indicates that the address bus may be available for use by the MPC8280
(see BG). The MPC8280 also tracks the state of ABB on the bus from the TS and
AACK inputs. (See section on address arbitration phase.)
Assertion—May occur whenever the MPC8280 must be prevented from using the
address bus.
Negation—May occur whenever the MPC8280 may use the address bus.
Address Transfer Start Signal
In the internal only mode the address transfer start signal has no meaning.
Address transfer start signal are input and output signals that indicate that an address bus transfer has
begun.
7.2.2.1
Transfer Start (TS)
The TS signal is both an input and an output signal on the MPC8280.
7.2.2.1.1
Transfer Start (TS)—Output
Following are the state meaning and timing comments for the TS output signal.
State Meaning
Asserted—Indicates that the MPC8280 has started a bus transaction and that the
address bus and transfer attribute signals are valid. It is also an implied data bus
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
7-5
60x Signals
Timing Comments
7.2.2.2
request if the transfer attributes TT[0–4] indicate that a data tenure is required for
the transaction.
Negated—Has no special meaning during a normal transaction.
Assertion/Negation—Driven and asserted on the cycle after a qualified BG is
accepted by MPC8280; remains asserted for one clock only. Negated for the
remainder of the address tenure. Assertion is coincident with the first clock that
ABB is asserted.
High Impedance—Occurs the cycle following the assertion of AACK (same cycle
as ABB negation).
Transfer Start (TS)—Input
Following are the state meaning and timing comments for the TS input signal.
State Meaning
Asserted—Indicates that another device has begun a bus transaction and that the
address bus and transfer attribute signals are valid for snooping.
Negated—Has no special meaning.
Timing Comments
Assertion/Negation—Must be asserted for one cycle only and then immediately
negated. Assertion may occur at any time during the assertion of ABB.
7.2.3
Address Transfer Signals
In internal only mode the memory controller uses these signals for glueless address transfers to memory
and I/O devices.
The address transfer signals are used to transmit the address.
7.2.3.1
Address Bus (A[0–31])
The address bus (A[0–31]) consists of 32 signals that are both input and output signals.
7.2.3.1.1
Address Bus (A[0–31])—Output
Following are the state meaning and timing comments for the A[0–31] output signals.
State Meaning
Content—Specifies the physical address of the bus transaction. For burst or
extended operations, the address is a double-word.
Timing Comments
Assertion/Negation—Driven valid on the same cycle that TS is driven/asserted;
remains driven/valid for the duration of the address tenure.
High Impedance— Occurs the cycle following the assertion of AACK; no
precharge action performed on release.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
7-6
Freescale Semiconductor
60x Signals
7.2.3.1.2
Address Bus (A[0–31])—Input
Following are the state meaning and timing comments for the A[0–31] input signals.
State Meaning
Asserted—Indicates that another device has begun a bus transaction and that the
address bus and transfer attribute signals are valid for snooping and in slave mode.
Negated—Has no special meaning.
Timing Comments
Assertion/Negation—Must be valid on the same cycle that TS is asserted; sampled
by the processor only on this cycle.
7.2.4
Address Transfer Attribute Signals
In internal only mode the address transfer attribute signals have no meaning.
The transfer attribute signals are a set of signals that further characterize the transfer—such as the size of
the transfer, whether it is a read or write operation, and whether it is a burst or single-beat transfer. For a
detailed description of how these signals interact, see Section 7.2.4, “Address Transfer Attribute Signals.”
7.2.4.1
Transfer Type (TT[0–4])
The transfer type signals (TT[0–4]) consist of five input/output signals on the MPC8280. For a complete
description of TT[0–4] signals and transfer type encoding, see Section 8.4.3.1, “Transfer Type Signal
(TT[0–4]) Encoding.”
7.2.4.1.1
Transfer Type (TT[0–4])—Output
Following are the state meaning and timing comments for the TT[0–4] output signals on the MPC8280.
State Meaning
Asserted/Negated—Specifies the type of transfer in progress.
Timing Comments
Assertion/Negation—Same as A[0–31].
High Impedance—Same as A[0–31].
7.2.4.1.2
Transfer Type (TT[0–4])—Input
Following are the state meaning and timing comments for the TT[0–4] input signals on the MPC8280.
State Meaning
Asserted/Negated—Specifies the type of transfer in progress for snooping by the
MPC8280.
Timing Comments
Assertion/Negation—Same as A[0–31].
7.2.4.2
Transfer Size (TSIZ[0–3])
The transfer size (TSIZ[0–3]) signals consist of four input/output signals on the MPC8280, following are
the state meaning and timing comments for the TSIZ[0–3] signals on the MPC8280.
State Meaning
Asserted/Negated—Specifies the data transfer size for the transaction (see
Section 8.4.3.3, “TBST and TSIZ[0–3] Signals and Size of Transfer”). During
graphics transfer operations, these signals form part of the Resource ID (see
TBST).
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
7-7
60x Signals
Timing Comments
7.2.4.3
Assertion/Negation—Same as A[0–31].
High Impedance—Same as A[0–31].
Transfer Burst (TBST)
The transfer burst (TBST) signal is an input/output signal on the MPC8280. Following are the state
meaning and timing comments for the TBST output/input signal.
State Meaning
Timing Comments
7.2.4.4
Asserted—Indicates that a burst transfer is in progress (see Section 8.4.3.3,
“TBST and TSIZ[0–3] Signals and Size of Transfer”). During graphics transfer
operations, this signal forms part of the Resource ID field from the EAR as
follows:
TBST || TSIZ[0–3] = EAR[28–31]. (See TBST.)
Negated—Indicates that a burst transfer is not in progress.
Assertion/Negation—Same as A[0–31].
High Impedance—Same as A[0–31].
Global (GBL)
The global (GBL) signal is an input/output signal on the MPC8280.
7.2.4.4.1
Global (GBL)—Output
Following are the state meaning and timing comments for the GBL output signal.
State Meaning
Asserted—Indicates that the transaction is global and should be snooped by other
devices. GBL reflects the M bit (WIM bits) from the MMU except during certain
transactions.
Negated—Indicates that the transaction is not global and should not be snooped
by other devices.
Timing Comments
Assertion/Negation—Same as A[0–31].
High Impedance—Same as A[0–31].
7.2.4.4.2
Global (GBL)—Input
Following are the state meaning and timing comments for the GBL input signal.
State Meaning
Asserted—Indicates that a transaction must be snooped by MPC8280.
Negated—Indicates that a transaction should not be snooped by MPC8280. (In
addition, certain non-global transactions are snooped for reservation coherency.)
Timing Comments
Assertion/Negation—Same as A[0–31].
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
7-8
Freescale Semiconductor
60x Signals
7.2.4.5
Caching-Inhibited (CI)—Output
The cache inhibit (CI) signal is an output signal on the MPC8280. Following are the state meaning and
timing comments for CI.
State Meaning
Timing Comments
7.2.4.6
Asserted—Indicates that the transaction in progress should not be cached. CI
reflects the I bit (WIM bits) from the MMU except during certain transactions.
Negated—Indicates that the transaction should be cached.
Assertion/Negation—Same as A[0–31].
High Impedance—Same as A[0–31].
Write-Through (WT)—Output
The write-through (WT) signal is an output signal on the MPC8280. Following are the state meaning and
timing comments for WT.
State Meaning
Asserted—Indicates that the transaction should operate in write-through mode.
WT reflects the W bit (WIM bits) from the MMU except during certain
transactions. WT may be asserted during read transactions.
Negated—Indicates that the transaction should not operate in write-through mode.
Timing Comments
Assertion/Negation—Same as A[0–31].
High Impedance—Same as A[0–31].
7.2.5
Address Transfer Termination Signals
The address transfer termination signals are used to indicate either that the address phase of the transaction
has completed successfully or must be repeated, and when it should be terminated. For detailed
information about how these signals interact, see Section 7.2.5, “Address Transfer Termination Signals.”
The address transfer termination signals have no meaning in internal only mode.
7.2.5.1
Address Acknowledge (AACK)
The address acknowledge (AACK) signal is an input/output on the MPC8280.
7.2.5.1.1
Address Acknowledge (AACK)—Output
.Following are the state meaning and timing comments for AACK as an output signal.
State Meaning
Asserted—Indicates that the address tenure of a transaction is terminated. On the
cycle following the assertion of AACK, the bus master releases the
address-tenure-related signals to the high-impedance state and samples ARTRY.
Timing Comments
Negated—Indicates that the address bus and the transfer attributes must remain
driven, if negated during ABB.
Assertion—Occurs a programmable number of clocks after TS or whenever
ARTRY conditions are resolved.
Negation—Occurs one clock after assertion.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
7-9
60x Signals
7.2.5.1.2
Address Acknowledge (AACK)—Input
Following are the state meaning and timing comments for AACK as an input signal.
State Meaning
Asserted—Indicates that a 60x bus slave is terminating the address tenure. On the
cycle following the assertion of AACK, the bus master releases the address tenure
related signals to the high-impedance state and samples ARTRY.
Timing Comments
7.2.5.2
Negated—Indicates that the address tenure must remain active and the address
tenure related signals driven.
Assertion—Occurs during the 60x bus slave access, at least two clocks after TS.
Negation—Occurs one clock after assertion.
Address Retry (ARTRY)
The address retry (ARTRY) signal is both an input and output signal on the MPC8280.
7.2.5.2.1
Address Retry (ARTRY)—Output
Following are the state meaning and timing comments for ARTRY as an output signal.
State Meaning
Asserted—Indicates that the MPC8280 detects a condition in which an address
tenure must be retried. If the MPC8280 processor needs to update memory as a
result of snoop that caused the retry, the MPC8280 asserts BR the second cycle
after AACK if ARTRY is asserted.
High Impedance—Indicates that the MPC8280 does not need the address tenure
to be retried.
Timing Comments
Assertion—Asserted the third bus cycle following the assertion of TS if a retry is
required.
Negation—Occurs the second bus cycle after the assertion of AACK. Since this
signal may be simultaneously driven by multiple devices, it negates in a unique
fashion. First the buffer goes to high impedance for a minimum of one-half
processor cycle (dependent on the clock mode), then it is driven negated for one
bus cycle before returning to high impedance.
7.2.5.2.2
Address Retry (ARTRY)—Input
Following are the state meaning and timing comments for the ARTRY input.
State Meaning
Asserted—If the MPC8280 is the address bus master, ARTRY indicates that the
MPC8280 must retry the preceding address tenure and immediately negate BR (if
asserted). If the associated data tenure has started, the MPC8280 also aborts the
data tenure immediately even if the burst data has been received. If the MPC8280
is not the address bus master, this input indicates that the MPC8280 should negate
BR for one bus clock cycle immediately after external device asserts ARTRY to
permit a copy-back operation to main memory. Note that the subsequent address
presented on the address bus may not be the one that generated the assertion of
ARTRY.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
7-10
Freescale Semiconductor
60x Signals
Timing Comments
7.2.6
Negated/High Impedance—Indicates that the MPC8280 does not need to retry the
last address tenure.
Assertion—May occur as early as the second cycle following the assertion of TS
and must occur by the bus clock cycle immediately following the assertion of
AACK if an address retry is required.
Negation—Must occur during the second cycle after the assertion of AACK.
Data Bus Arbitration Signals
The data bus arbitration signals have no meaning in internal-only mode.
Like the address bus arbitration signals, data bus arbitration signals maintain an orderly process for
determining data bus mastership. Note that there is no data bus arbitration signal equivalent to the address
bus arbitration signal BR (bus request), because, except for address-only transactions, TS implies data bus
requests. For a detailed description on how these signals interact, see Section 8.5.1, “Data Bus
Arbitration.”
7.2.6.1
Data Bus Grant (DBG)
The data bus grant signal (DBG) is an output/input on the MPC8280.
7.2.6.1.1
Data Bus Grant (DBG)—Input
DBG an input when MPC8280 is configured to an external arbiter. The following are the state meaning
and timing comments for DBG.
State Meaning
Asserted—Indicates that the MPC8280 may, with the proper qualification, assume
mastership of the data bus. The MPC8280 derives a qualified data bus grant when
DBG is asserted and DBB and ARTRY are negated; that is, the data bus is not busy
(DBB is negated), and there is no outstanding attempt to perform an ARTRY of
the associated address tenure.
Negated—Indicates that the MPC8280 must hold off its data tenures.
Timing Comments
Assertion—May occur any time to indicate the MPC8280 is free to take data bus
mastership. It is not sampled until TS is asserted.
Negation—May occur at any time to indicate the MPC8280 cannot assume data
bus mastership.
7.2.6.1.2
Data Bus Grant (DBG)—Output
DBG signal is output when the MPC8280 configured to use the internal arbiter. Following are the state
meaning and timing comments for the DBG signal.
State Meaning
Asserted—Indicates that the external device may, with the proper qualification,
assume mastership of the data bus. A qualified data bus grant is defined as the
assertion of DBG, negation of DBB, and negation of ARTRY. The requirement for
the ARTRY signal is only for the address bus tenure associated with the data bus
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
7-11
60x Signals
Timing Comments
7.2.6.2
tenure about to be granted (that is, not for another address tenure available because
of address pipelining).
Negated—Indicates that an external device is not granted mastership of the data
bus.
Assertion—Occurs on the first clock in which the data bus is not busy and the
processor has the highest priority outstanding data transaction.
Negation—Occurs one clock after assertion.
Data Bus Busy (DBB)
The data bus busy (DBB) signal is both an input and output signal on the MPC8280.
7.2.6.2.1
Data Bus Busy (DBB)—Output
Following are the state meaning and timing comments for the DBB output signal.
State Meaning
Asserted—Indicates that the MPC8280 is the data bus master. The MPC8280
always assumes data bus mastership if it needs the data bus and determines a
qualified data bus grant (see DBG).
Timing Comments
7.2.6.2.2
Negated—Indicates that the MPC8280 is not using the data bus.
Assertion—Occurs during the bus clock cycle following a qualified DBG.
Negation—Occurs for a minimum of one-half bus clock cycle following the
assertion of the final TA following TEA or certain ARTRY cases.
High Impedance—Occurs after DBB is negated.
Data Bus Busy (DBB)—Input
Following are the state meaning and timing comments for the DBB input signal.
State Meaning
Asserted—Indicates that another device is bus master.
Negated—Indicates that the data bus is free (with proper qualification, see DBG)
for use by the MPC8280.
Timing Comments
Assertion—Must occur when the MPC8280 must be prevented from using the
data bus.
Negation—May occur whenever the data bus is available.
7.2.7
Data Transfer Signals
Data transfer signals are used in the same way in both internal only and external master modes. Like the
address transfer signals, the data transfer signals are used to transmit data and to generate and monitor
parity for the data transfer. For a detailed description of how data transfer signals interact, see
Section 7.2.7, “Data Transfer Signals.”
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
7-12
Freescale Semiconductor
60x Signals
7.2.7.1
Data Bus (D[0–63])
The data bus (D[0–63]) states have the same meanings in both internal only mode external master mode.
The data bus consists of 64 signals that are both inputs and outputs on the MPC8280. Following are the
state meaning and timing comments for the data bus.
State Meaning
The data bus holds 8 byte lanes assigned as shown in Table 7-2.
Timing Comments
The number of times the data bus is driven depends on the transfer size, port size,
and whether the transfer is a single-beat or burst operation.
7.2.7.1.1
Data Bus (D[0–63])—Output
Following are the state meaning and timing comments for the D[0–63] output signals.
State Meaning
Asserted/Negated—Represents the state of data during a data write. Byte lanes not
selected for data transfer do not supply valid data. MPC8280 duplicates data to
enable valid data to be sent to different port sizes.
Timing Comments
Assertion/Negation—Initial beat coincides with DBB, for bursts, transitions on
the bus clock cycle following each assertion of TA and, for port size, transitions
on the bus clock cycle following each assertion of PSDVAL.
High Impedance—Occurs on the bus clock cycle after the final assertion of TA,
TEA, or certain ARTRY cases.
Table 7-1. Data Bus Lane Assignments
7.2.7.1.2
Data Bus Signals
Byte Lane
D0–D7
0
D8–D15
1
D16–D23
2
D24–D31
3
D32–D39
4
D40–D47
5
D48–D55
6
D56–D63
7
Data Bus (D[0–63])—Input
Following are the state meaning and timing comments for the D[0–63] input signals.
State Meaning
Asserted/Negated—Represents the state of data during a data read transaction.
Timing Comments
Assertion/Negation—Data must be valid on the same bus clock cycle that TA
and/or PSDVAL is asserted.
7.2.7.2
Data Bus Parity (DP[0–7])
The eight data bus parity (DP[0–7]) signals both output and input signals.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
7-13
60x Signals
7.2.7.2.1
Data Bus Parity (DP[0–7])—Output
Following are the state meaning and timing comments for the DP[0–7] output signals.
State Meaning
Asserted/Negated—Represents odd parity for each of 8 bytes of data write
transactions. Odd parity means that an odd number of bits, including the parity bit,
are driven high. The signal assignments are listed in Table 7-2.
Table 7-2. DP[0–7] Signal Assignments
Timing Comments
7.2.7.2.2
Signal Name
Data Bus Signal Assignments
DP0
D[0–7]
DP1
D[8–15
DP2
D[16–23]
DP3
D[24–31]
DP4
D[32–39]
DP5
D[40–47]
DP6
D[48–55]
DP7
D[56–63]
Assertion/Negation—The same as the data bus.
High Impedance—The same as the data bus.
Data Bus Parity (DP[0–7])—Input
Following are the state meaning and timing comments for the DP input signals.
State Meaning
Asserted/Negated—Represents odd parity for each byte of read data. Parity is
checked on all data byte lanes, regardless of the size of the transfer. Detected even
parity causes a checkstop if data parity errors are enabled in the BCS[PAR_EN].
Timing Comments
Assertion/Negation—The same as D[0–63].
7.2.8
Data Transfer Termination Signals
Data termination signals are required after each data beat in a data transfer. Note that in a single-beat
transaction that is not a port-size transfer, the data termination signals also indicate the end of the tenure.
In burst or port size accesses, the data termination signals apply to individual beats and indicate the end of
the tenure only after the final data beat. For a detailed description of how these signals interact, see
Section 8.5, “Data Tenure Operations.”
7.2.8.1
Transfer Acknowledge (TA)
The transfer acknowledge (TA) signal is both input and output on the MPC8280.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
7-14
Freescale Semiconductor
60x Signals
7.2.8.1.1
Transfer Acknowledge (TA)—Input
Following are the state meaning and timing comments for the TA input signal.
State Meaning
Asserted—Indicates that a single-beat data transfer completed successfully or that
a data beat in a burst transfer completed successfully. Note that TA must be
asserted for each data beat in a burst transaction. For more information, see
Section 8.5.3, “Data Bus Transfers and Normal Termination.”
Negated—(During assertion of DBB) indicates that, until TA is asserted, the
MPC8280 must continue to drive the data for the current write or must wait to
sample the data for reads.
Timing Comments
Assertion—Depends on whether or not the PCI controller can initiate 60x bus
global transactions when the address retry mechanism is in use:
PCI controller is not used or cannot initiate global transactions— Assertion must
occur at least one cycle following AACK for the current transaction;
otherwise, assertion may occur at any time during the assertion of DBB.
The system can withhold assertion of TA to indicate that the MPC8280
should insert wait states to extend the duration of the data beat.
PCI controller can initiate global transactions—Assertion must occur at least one
clock cycle following AACK for the current transaction and at least one
clock cycle after ARTRY can be asserted.
Negation—Must occur after the bus clock cycle of the final (or only) data beat of
the transfer. For a burst transfer, the system can assert TA for one bus clock cycle
and then negate it to advance the burst transfer to the next beat and insert wait
states during the next beat. (Note: when configured for 1:1 clock mode and is
performing a burst read into the data cache, the MPC8280 requires two wait states
between the assertion of TS and the first assertion of TA for that transaction, or
one wait state for 1.5:1 clock mode.)
7.2.8.1.2
Transfer Acknowledge (TA)—Output
Following are the state meaning and timing comments for TA as an output signal.
State Meaning
Asserted—Indicates that the data has been latched for a write operation, or that the
data is valid for a read operation, thus terminating the current data beat. If it is the
last or only data beat, this also terminates the data tenure.
Negated—Indicates that master must extend the current data beat (insert wait
states) until data can be provided or accepted by the MPC8280.
Timing Comments
Assertion—Depends on whether or not the PCI controller can initiate 60x bus
global transactions when the address retry mechanism is in use:
PCI controller is not used or cannot initiate global transactions—Assertion must
occur at least one cycle following AACK for the current transaction;
occurs on the clock in which the current data transfer can be completed.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
7-15
60x Signals
PCI controller can initiate global transactions—Assertion must occur at least one
clock cycle following AACK for the current transaction and at least one
clock cycle after ARTRY can be asserted.
Negation—Occurs after the clock cycle of the final (or only) data beat of the
transfer. For a burst transfer, TA may be negated between beats to insert one or
more wait states before the completion of the next beat.
7.2.8.2
Transfer Error Acknowledge (TEA)
The transfer error acknowledge (TEA) signal is both input and output on the MPC8280.
7.2.8.2.1
Transfer Error Acknowledge (TEA)—Input
Following are the state meaning and timing comments for the TEA input signal.
State Meaning
Timing Comments
7.2.8.2.2
Asserted—Indicates that a bus error occurred. The assertion of TEA causes the
negation/high impedance of DBB in the next clock cycle. However, data entering
the MPC8280 internal memory resources such as GPRs or caches are not
invalidated.
Negated—Indicates that no bus error was detected.
Assertion—May be asserted while DBB is asserted and for the cycle after is TA is
asserted during a read operation. TEA should be asserted for one cycle only.
Negation—TEA must be negated no later than the negation of DBB.
Transfer Error Acknowledge (TEA)—Output
Following are the state meaning and timing comments for the TEA output.
State Meaning
Asserted—Indicates that a bus error has occurred. Assertion of TEA terminates
the transaction in progress; that is, asserting TA is unnecessary because it is
ignored by the target device. An unsupported memory transaction, such as a
direct-store access or a graphics read or write, causes the assertion of TEA
(provided TEA is enabled and the address transfer matches the MPC8280 memory
map).
Negated—Indicates that no bus error was detected.
Timing Comments
Assertion—Occurs on the first clock after the bus error is detected.
Negation—Occurs one clock after assertion.
7.2.8.3
Partial Data Valid Indication (PSDVAL)
The partial data valid indication (PSDVAL) is both an input and output on the MPC8280.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
7-16
Freescale Semiconductor
60x Signals
7.2.8.3.1
Partial Data Valid (PSDVAL)—Input
Following are the state meaning and timing comments for the PSDVAL input signal. Note that TA asserts
with PSDVAL to indicate the termination of the current transfer and for each complete data beat in burst
transactions.
State Meaning
Asserted—Indicates that a beat data transfer completed successfully. Note that
PSDVAL must be asserted for each data beat in a single beat, port size and burst
transaction,. For more information, see Section 8.5.5, “Port Size Data Bus
Transfers and PSDVAL Termination.”
Negated—(During DBB) indicates that, until PSDVAL is asserted, the MPC8280
must continue to drive the data for the current write or must wait to sample the data
for reads.
Timing Comments
Assertion—Must not occur before AACK for the current transaction (if the
address retry mechanism is to be used to prevent invalid data from being used by
the MPC8280); otherwise, assertion may occur at any time during the assertion of
DBB. The system can withhold assertion of PSDVAL to indicate that the
MPC8280 should insert wait states to extend the duration of the data beat.
Negation—Must occur after the bus clock cycle of the final (or only) data beat of
the transfer. For a burst and/or port size transfer, the system can assert PSDVAL
for one bus clock cycle and then negate it to insert wait states during the next beat.
(Note: when the MPC8280 processor is configured for 1:1 clock mode and is
performing a burst read into the data cache, the MPC8280 requires two wait state
between the assertion of TS and the first assertion of PSDVAL for that transaction,
or 1 wait state for 1.5:1 clock mode.)
7.2.8.3.2
Partial Data Valid (PSDVAL)—Output
Following are the state meaning and timing comments for PSDVAL as an output signal.
State Meaning
Asserted—Indicates that the data has been latched for a write operation, or that the
data is valid for a read operation, thus terminating the current data beat. If it is the
last or only data beat, this also terminates the data tenure.
Negated—Indicates that the master must extend the current data beat (insert wait
states) until data can be provided or accepted by the MPC8280.
Timing Comments
Assertion—Occurs on the clock in which the current data transfer can be
completed.
Negation—Occurs after the clock cycle of the final (or only) data beat of the
transfer. For a burst transfer, PSDVAL may be negated between beats to insert one
or more wait states before the completion of the next beat.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
7-17
60x Signals
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
7-18
Freescale Semiconductor
Chapter 8
The 60x Bus
The 60x bus, which is used by processors that implement the PowerPC architecture, provides flexible
support for the on-chip MPC603 processor as well as other internal and external bus devices. The 60x bus
supports 32-bit addressing, a 64-bit data bus, and burst operations that transfer as many as 256 bits of data
in a four-beat burst. The 60x data bus can be accessed in 8-, 16-, 32-, and 64-bit data ports. The 60x bus
supports accesses of 1, 2, 3, and 4 bytes, aligned or unaligned, on 4-byte (word) boundaries; it also supports
64-, 128-, 192-, and 256-bit accesses.
The address and data buses support synchronous, one-level pipeline transactions. The 60x bus interface
can be configured to support both external and internal masters or internal masters only.
8.1
Terminology
Table 8-1 defines terms used in this chapter.
Table 8-1. Terminology
Term
Definition
Atomic
A bus access that attempts to be part of a read-write operation to the same address uninterrupted
by any other access to that address. The MPC8280 initiates the read and write separately, but
signals the memory system that it is attempting an atomic operation. If the operation fails, status is
kept so that MPC8280 can try again.
Beat
A single state on the MPC8280 interface that may extend across multiple bus cycles. (An MPC8280
transaction can be composed of multiple address or data beats.)
Burst
A multiple-beat data transfer whose total size is typically equal to a cache block size (in MPC8280:
32 bytes, or 4 data beats at 8 bytes per beat).
Cache block
The PowerPC architecture defines the basic unit of coherency as a cache block, which can be
considered the same thing as a cache line.
Clean
An operation that causes a cache block to be written to memory if modified, and then left in a valid,
unmodified state in the cache.
Flush
An operation that causes a cache block to be invalidated in the cache, and its data, if modified, to
be written back to main memory.
Kill
An operation that causes a cache block to be invalidated in the cache without writing any modified
data to memory.
Lane
A sub-grouping of signals within a bus. An 8-bit section of the address or data bus may be referred
to as a byte lane for that bus.
Master
The device that owns the address or data bus, the device that initiates or requests the transaction.
Modified
Identifies a cache block The M state in a MESI or MEI protocol.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
8-1
The 60x Bus
Table 8-1. Terminology (continued)
Term
Definition
Parking
Granting potential bus mastership without requiring a bus request from that device. This eliminates
the arbitration delay associated with the bus request.
Pipelining
Initiating a bus transaction before the current one finishes. This involves running an address tenure
for a new bus transaction before the data tenure for a current bus transaction completes.
Slave
The device addressed by the master. The slave is identified in the address tenure and is responsible
for sourcing or sinking the requested data for the master during the data tenure.
Snooping
Monitoring addresses driven by a bus master to detect the need for coherency actions.
Split-transaction A transaction with separate request and response tenures.
Tenure
The period of bus mastership. For MPC8280, there can be separate address bus tenures and data
bus tenures.
Transaction
A complete exchange between two bus devices. A typical transaction is composed of an address
tenure and a data tenure, which may overlap or occur separately from the address tenure. A
transaction can minimally consist of an address tenure alone.
8.2
Bus Configuration
The 60x bus supports separate bus configurations for internal masters and external bus masters.
• Single-MPC8280 bus mode connects external devices by using only the memory controller. This
is described in Section 8.2.1, “Single-MPC8280 Bus Mode.”
• The 60x-compatible bus mode, described in Section 8.2.2, “60x-Compatible Bus Mode,” enables
connections to other masters and 60x-bus slaves, such as an external L2 cache controller.
The figures in the following sections show how the MPC8280 can be connected in these two
configurations.
8.2.1
Single-MPC8280 Bus Mode
In single-MPC8280 bus mode, the MPC8280 is the only bus device in the system. The internal memory
controller controls all devices on the external pins. Figure 8-1 shows the signal connections for
single-MPC8280 bus mode.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
8-2
Freescale Semiconductor
The 60x Bus
MPC8280
APE
TS
Latch &
A[0–31]
DRAM MUX
I/O
TT[0–4]
TBST
CI
WT
Address + Attributes
TSIZ[0–3]
MEM
GBL
ARTRY
DBG
D[0–63]
DP[0–7]
TA
Memory Controller Signals
Data + Attributes
AACK
TEA
Memory Control Signals
Figure 8-1. Single-MPC8280 Bus Mode
NOTE
In single-MPC8280 bus mode, the MPC8280 uses the address bus as a
memory address bus. Slaves cannot use the 60x bus signals because the
addresses have memory timing, not address tenure timing.
8.2.2
60x-Compatible Bus Mode
The 60x-compatible bus mode can include one or more potential external masters (for example, an L2
cache, an ASIC DMA, a high-end processor that implements the PowerPC architecture, or a second
MPC8280). When operating in a multiprocessor configuration, the MPC8280 snoops bus operations and
maintains coherency between the primary caches and main memory. Figure 8-2 shows how an external
processor is attached to the MPC8280.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
8-3
The 60x Bus
MPC8280
APE
TS
BR
BG
TS
A[0–31]
AP[0–3]
Latch
I/O
TT[0–4]
TSIZ[0–3]
GBL
AACK
ARTRY
Data + Attributes
WT
Address + Attributes
CI
Memory Controller Signals
TBST
Latch &
MEM
DRAM MUX
DBG
External Device
Memory Control Signals
BR
D[0–63]
BG
DP[0–7]
DBG
TA
TEA
Figure 8-2. 60x-Compatible Bus Mode
8.3
60x Bus Protocol Overview
Typically, 60x bus accesses consist of address and data tenures, which in turn each consist of three
phases—arbitration, transfer, and termination, as shown in Figure 8-3.. The independence of the tenures is
indicated by showing the data tenure overlap the next address tenure, which allows split-bus transactions
to be implemented at the system level in multiprocessor systems. Figure 8-3 shows a data transfer that
consists of a single-beat transfer of as many as 256 bits. Four-beat burst transfers of 32-byte cache blocks
require data transfer termination signals for each beat of data. Note that the MPC8280 supports port sizes
of 8, 16, 32, and 64 bits and requires the additional bus signal, PSDVAL, which is not defined by the 60x
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
8-4
Freescale Semiconductor
The 60x Bus
bus specification. For more information, see Section 8.5.5, “Port Size Data Bus Transfers and PSDVAL
Termination.”
Data Tenure
Arbitration
1- or 4-Beat Transfer
Termination
Independent Address and Data Tenures
Next Address Tenure
Arbitration
Transfer
Termination
Figure 8-3. Basic Transfer Protocol
The basic functions of the address and data tenures are as follows:
• Address tenure
— Arbitration: Address bus arbitration signals are used to request and grant address bus
mastership.
— Transfer: After a device is granted address bus mastership, it transfers the address. The address
signals and the transfer attribute signals control the address transfer.
— Termination: After the address transfer, the system acknowledges that the address tenure is
complete or that it must be repeated, signalled by the assertion of the address retry signal
(ARTRY).
• Data tenure
— Arbitration: After the address tenure begins, the bus device arbitrates for data bus mastership.
— Transfer: After the device is granted data bus mastership, it samples the data bus for read
operations or drives the data bus for write operations.
— Termination: Acknowledgment of a successful data transfer is required after each beat in a data
transfer. In single-beat transactions, the data termination signals also indicate the end of the
tenure. In burst or port-size accesses, data termination signals indicate the completion of
individual beats and, after the final data beat, the end of the tenure.
8.3.1
Arbitration Phase
The external bus design permits one device (either the MPC8280 or a bus-attached external device) to be
granted bus mastership at a time. Bus arbitration can be handled either by an external central bus arbiter
or by the internal on-chip arbiter. In the latter case, the system is optimized for three external bus masters
besides the MPC8280. The arbitration configuration (external or internal) is determined at system reset by
sampling configuration pins. See Section 4.3.2.2, “60x Bus Arbiter Configuration Register (PPC_ACR),”
for more information.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
8-5
The 60x Bus
The MPC8280 controls bus access through the bus request (BR) and bus grant (BG) signals. It determines
the state of the address and data bus busy signals by monitoring DBG, TS, AACK, and TA, and it qualifies
them with ABB and DBB.
The following signals are used for address bus arbitration:
• BR (bus request)—A device asserts BR to request address bus mastership.
• BG (bus grant)—Assertion indicates that a bus device may, with proper qualification, assume
mastership of the address bus. A qualified bus grant occurs when BG is asserted while ABB and
ARTRY are negated.
• ABB (address bus busy)—A device asserts ABB to indicate it is the current address bus master.
Note that if all devices assert ABB with TS and would normally negate ABB after AACK is
asserted, the devices can ignore ABB because the MPC8280 can internally generate ABB. The
MPC8280’s ABB, if enabled, must be tied to a pull-up resistor.
The following signals are used for data bus arbitration:
• DBG (data bus grant)—Indicates that a bus device can, with the proper qualification, assume data
bus mastership. A qualified data bus grant occurs when DBG is asserted while DBB and ARTRY
are negated.
• DBB (data bus busy)—Assertion by the device indicates that the device is the current data bus
master. The device master always assumes data bus mastership if it needs the data bus and is given
a qualified data bus grant (see DBG). Note that if all devices assert DBB in conjunction with
qualified data bus grant and would normally negate DBB after the last TA is asserted, the devices
can ignore DBB because the MPC8280 can generate DBB internally. The MPC8280’s DBB signal,
if enabled, must be tied to a pull-up resistor.
The following is a summary of rules for arbitration:
•
•
Preference among devices is determined at the request level. The MPC8280 supports eight levels
of bus requests.
When no bus device is requesting the address bus, the MPC8280 parks the device selected in the
arbiter configuration register on the bus.
For more information, see Section 4.3.2.2, “60x Bus Arbiter Configuration Register (PPC_ACR).”
8.3.2
Address Pipelining and Split-Bus Transactions
The 60x bus protocol provides independent address and data bus capability to support pipelined and
split-bus transaction system organizations. Address pipelining allows the next address tenure to begin
before the current data tenure has finished. Although this ability does not inherently reduce memory
latency, support for address pipelining and split-bus transactions can greatly improve effective
bus/memory throughput. These benefits are most fully realized in shared-memory, multiple-master
implementations where bus bandwidth is critical to system performance.
External arbitration (as provided by the MPC8280) is required in systems in which multiple devices share
the system bus. The MPC8280 uses the address acknowledge (AACK) signal to control pipelining. The
MPC8280 supports both one- and zero-level bus pipelining. One-level pipelining is achieved by asserting
AACK to the current address bus master and granting mastership of the address bus to the next requesting
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
8-6
Freescale Semiconductor
The 60x Bus
master before the current data bus tenure has completed. Two address tenures can occur before the current
data bus tenure completes. The MPC8280 also supports non-pipelined accesses.
8.4
Address Tenure Operations
This section describes the three phases of the address tenure—address bus arbitration, address transfer, and
address termination.
8.4.1
Address Arbitration
Bus arbitration can be handled either by an external arbiter or by the internal on-chip arbiter. The
arbitration configuration (external or internal) is chosen at system reset. For internal arbitration, the
MPC8280 provides arbitration for the 60x address bus and the system is optimized for three external bus
masters besides the MPC8280. The bus request (BR) for the external device is an external input to the
arbiter. The bus grant signal for the external device (BG) is output to the external device.The BG signal
asserted by MPC8280’s on-chip arbiter is asserted one clock after the current master on the bus has
asserted AACK; therefore, it can be called a qualified BG. Assuming that all potential masters negate ABB
one clock after receiving AACK, the device receiving BG can start the address tenure (by asserting TS)
one clock after receiving BG. In addition to the external signals, there are internal request and grant signals
for the MPC8280 processor, communications processor, refresh controller, and the PCI internal bridge.
Bus accesses are prioritized, with programmable priority. When a MPC8280’s internal master needs the
60x bus, it asserts the internal bus request along with the request level. The arbiter asserts the internal bus
grant for the highest priority request.
The MPC8280 supports address bus parking through the use of the parked master bits in the arbiter
configuration register. The MPC8280 parks the address bus (asserts the address bus grant signal in
anticipation of an address bus request) to the external master or internal masters. When a device is parked,
the arbiter can hold BG asserted for a device even if that device has not requested the bus. Therefore, when
the parked device needs to perform a bus transaction, it skips the bus request delay and assumes address
bus mastership on the next cycle. For this case, BR is not asserted and the access latency seen by the device
is shortened by one cycle.
The MPC8280 and external device bus devices qualify BG by sampling ARTRY in the negated state prior
to taking address bus mastership. The negation of ARTRY during the address retry window (one cycle after
the assertion of AACK) indicates that no address retry is requested. If a device detects ARTRY asserted,
it cannot accept a address bus grant during the ARTRY cycle or the cycle following. A device that asserts
ARTRY due to a modified cache block hit, for example, asserts its bus request during the cycle after the
assertion of ARTRY and assumes bus mastership for the cache block push when it is given a bus grant.
The series of address transfers in Figure 8-4 shows the transfer protocol when the MPC8280 is configured
in 60x-compatible bus mode. In this example, MPC8280 is initially parked on the bus with BG
INT-asserted (note that BG INT is an internal signal not seen by the user at the pins), which lets it start an
address bus tenure by asserting TS. During the same clock cycle, the external master’s bus request is
asserted to request access to the 60x bus, thereby causing the negation of BG INT internally and the
assertion of BG at the pin. Following MPC8280’s address tenure, the external master takes the bus and
initiates its address transaction. The on-chip arbiter samples BR during the clock cycle in which AACK is
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
8-7
The 60x Bus
asserted; if BR is not asserted (no pending request), it negates BG and asserts the parked bus grant
(BG_INT in this example).
The master can assert BR and receive a qualified bus grant without subsequently using the bus. It can
negate (cancel) BR before accepting a qualified bus grant. This can occur when a replacement copyback
transaction waiting to be run on the bus is killed by a snoop of another bus master. This can also occur
when the reservation set by a pending stwcx. transaction is cancelled by a snoop of another master. In both
cases, the pending transaction by the processor is cancelled and BR is negated.
CLKOUT
BR INT
MPC8280
BG INT
BR
BG
ABB
ADDR+
MPC8280
External
External
TS
AACK
ARTRY
Figure 8-4. Address Bus Arbitration with External Bus Master
8.4.2
Address Pipelining
The MPC8280 supports one-level address pipelining by asserting AACK to the current bus master when
its data tenure starts and by granting the address bus to the next requesting device before the current data
bus tenure completes. Address pipelining improves data throughput by allowing the memory-control
hardware to decode a new set of address and control signals while the current data transaction finishes.
The MPC8280 pipelines data bus operations in strict order with the associated address operations.
Figure 8-5 shows how address pipelining allows address tenures to overlap the associated data tenures.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
8-8
Freescale Semiconductor
The 60x Bus
CLKOUT
ADDR + ATTR
TS
AACK
DBG
TA
Address
Tenure
Address 1
Data Tenure
Address 2
Data 1
Data 2
Figure 8-5. Address Pipelining
8.4.3
Address Transfer Attribute Signals
During the address transfer, the address is placed on the address signals, A[0–31]. The bus master provides
other signals that characterize the address transfer—transfer type (TT[0–4]), transfer code (TC[0–2]),
transfer size (TSIZ[0–3]), and transfer burst (TBST) signals. These signals are discussed in the following
sections.
8.4.3.1
Transfer Type Signal (TT[0–4]) Encoding
The transfer type signals define the nature of the transfer requested. They indicate whether the operation
is an address-only transaction or whether both address and data are to be transferred. Table 8-2 describes
the MPC8280’s action as master, slave, and snooper.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
8-9
The 60x Bus
Table 8-2. Transfer Type Encoding
60x Bus Specification2
TT[0–4]
MPC8280 as Bus Master
1
Command
Transaction
Bus Trans.
Transaction Source
MPC8280 as
Snooper
MPC8280
as Slave
Action on Hit
Action on Slave Hit
00000
Clean block Address only Address only (if dcbst (if enabled)
enabled)
Not applicable
AACK asserted;
MPC8280 takes no
further action.
00100
Flush block
Address only Address only (if dcbf (if enabled)
enabled)
Not applicable
AACK is asserted;
MPC8280 takes no
further action.
01000
sync
Address only Address only (if sync (if enabled)
enabled)
Not applicable
Assert AACK. BG is
negated until MPC8280
buffers are flushed.
01100
Kill block
Address only Address only
Flush, cancel
reservation
AACK is asserted.
10000
eieio
Address only Address only (if eieio (if enabled)
enabled)
Not applicable
Assert AACK. BG is
negated until MPC8280
buffers are flushed.
101 00
Graphics
write
Single-beat
write
ecowx
Not applicable
No action.
11000
TLB
invalidate
Address only Not applicable
Not applicable
Not applicable
AACK is asserted;
MPC8280 takes no
further action.
11100
Graphics
read
Single-beat
read
Not applicable
MPC8280 takes no
action.
00001
lwarx
reservation
set
Address only Not applicable
Not applicable
Not applicable
Address-only
operation. AACK is
asserted; MPC8280
takes no further action.
00101
Reserved
—
Not applicable
Not applicable
Not applicable
Illegal
01001
tlbsync
Address only Not applicable
Not applicable
Not applicable
Address-only
operation. AACK is
asserted; MPC8280
takes no further action.
01101
icbi
Address only Not applicable
Not applicable
Not applicable
Address-only
operation. AACK is
asserted; MPC8280
takes no further action.
1XX01
Reserved
—
for customer
Not applicable
Not applicable
Illegal
00010
WR w/flush
CI, WT store, or
non-processor master
under
Flush, cancel
reservation
Write, assert AACK and
TA.
Single-beat
write
(non-GBL)
dcbz or dcbi (if
enabled)
Single-beat
eciwx
read (non-GBL)
Not applicable
Single-beat
Single-beat
write or Burst write
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
8-10
Freescale Semiconductor
The 60x Bus
Table 8-2. Transfer Type Encoding (continued)
60x Bus Specification2
MPC8280 as Bus Master
TT[0–4]1
Command
1
2
Transaction
Bus Trans.
Transaction Source
MPC8280 as
Snooper
MPC8280
as Slave
Action on Hit
Action on Slave Hit
00110
WR w/Kill
Burst
Burst
(non-GBL)
Castout, ca-op push, or Kill, cancel
snoop copyback
reservation
Write, assert AACK and
TA.
01010
Read
Single-beat
read or burst
Single-beat
read
CI load, CI I-fetch or
nonprocessor master
Clean or flush
Read, assert AACK
and TA.
01110
Read with
intent to
modify
Burst
Burst
Load miss, store miss,
or I-fetch
Flush
Read, assert AACK
and TA.
10010
WR w/flush
atomic
Single-beat
write
Single-beat
write
stwcx.
Flush, cancel
reservation
Write, assert AACK and
TA
10110
Reserved
Not
applicable
Not applicable
Not applicable
Not applicable
Illegal
11010
Read
atomic
Single-beat
read or burst
Single-beat
read
lwarx (CI load)
Clean or flush
Read, assert AACK
and TA
11110
Read with
intent to
modify
atomic
Burst
Burst
lwarx (load miss)
Flush
Read, assert AACK
and TA
00011
Reserved
—
Not applicable
Not applicable
Not applicable
Illegal
00111
Reserved
—
Not applicable
Not applicable
Not applicable
Illegal
01011
Read with
no intent to
cache
Single-beat
read or burst
Not applicable
Not applicable
Clean
Read, assert AACK
and TA
01111
Reserved
—
Not applicable
Not applicable
Not applicable
Illegal
1XX11
Reserved
—
for customer
Not applicable
Not applicable
Not applicable
Illegal
TT1 can be interpreted as a read-versus-write indicator for the bus.
This column specifies the TT encoding for the general 60x protocol. The processor generates or snoops only a subset of
those encodings.
NOTE
Regarding Table 8-2:
•
•
For reads, the processor cleans or flushes during a snoop based on the
TBST input. The processor cleans for single-beat reads (TBST negated)
to emulate read-with-no-intent-to-cache operations.
Castouts and snoop copybacks are generally marked as non-global and
are not snooped (except for reservation monitoring). However, other
masters performing DMA write operations with the same TT encoding
and marked as a global WR operation (whether global or non-global)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
8-11
The 60x Bus
•
8.4.3.2
will cancel an active reservation during a snoop hit in the reservation
register (independent of a snoop hit in the cache).
A non-processor read can cause the internal processor to invalidate the
corresponding cache line if it exists.
Transfer Code Signals TC[0–2]
The transfer code signals, TC[0–2], provide supplemental information about the corresponding address
(mainly regarding the source of the transaction). Note that TCx signals can be used with the TT[0–4] and
TBST to further define the current transaction.
Table 8-3. Transfer Code Encoding for 60x Bus
60x Bus
TC[0–2]
Read
Write
000
Core data transaction
Any write
001
Core touch load
—
010
Core instruction fetch
—
011
Reserved
—
100
8.4.3.3
101
Reserved
110
DMA function code 0
111
DMA function code 1
TBST and TSIZ[0–3] Signals and Size of Transfer
As shown in Table 8-4, the transfer size signals (TSIZ[0–3]) and the transfer burst signal (TBST) together
indicate the size of the requested data transfer. These signals can be used with address bits A[27–31] and
the device port size to determine which portion of the data bus contains valid data for a write transaction
or which portion of the bus should contain valid data for a read transaction.
The MPC8280 uses four double word burst transactions for transferring cache blocks. For these
transactions, TSIZ[0–3] are encoded as 0b0010, and address bits A[27–28] determine which double-word
is sent first.
The MPC8280 supports critical-word-first burst transactions (double-word-aligned) from the processor.
The MPC8280 transfers the critical double word of data first, followed by the double words from
increasing addresses, wrapping back to the beginning of the eight-word block as required.
Table 8-4. Transfer Size Signal Encoding
TBST
TSIZ[0–3]
Transfer Size
Comments
Source
Negated
0 0 0 1
1 Byte
Byte
Core and DMA
Negated
0 0 1 0
2 Bytes
Half word
Core and DMA
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
8-12
Freescale Semiconductor
The 60x Bus
Table 8-4. Transfer Size Signal Encoding (continued)
TBST
TSIZ[0–3]
Transfer Size
Comments
Source
Negated
0 0 1 1
3 Bytes
—
Core and DMA
Negated
0 1 0 0
4 Bytes
Word
Core and DMA
Negated
0 1 0 1
5 Bytes
Extended 5 bytes
SDMA (MPC8280 only)
Negated
0 1 1 0
6 Bytes
Extended 6 bytes
SDMA (MPC8280 only)
Negated
0 1 1 1
7 Bytes
Extended 7 bytes
SDMA (MPC8280 only)
Negated
0 0 0 0
8 Bytes
Double-word (maximum data bus size)
Core and DMA
Negated
1 0 0 1
16 Bytes
Extended double double word
SDMA (MPC8280 only)
Negated
1 0 1 0
24 Bytes
Extended triple double word
SDMA (MPC8280 only)
Asserted
0 0 1 0
32 bytes
Quad double-word (4 maximum data
beats)
Core and DMA
NOTE
The basic coherency size of the bus is 32 bytes for the processor
(cache-block size). Data transfers that cross an aligned 32-byte boundary
must present a new address onto the bus at that boundary for proper snoop
operation, or must operate as non-coherent with respect to the MPC8280.
8.4.3.4
Burst Ordering During Data Transfers
During burst transfers, 32 bytes of data (one cache block) are transferred to or from the cache. Burst write
transfers are performed zero double-word-first. However, because burst reads are performed
critical-double-word-first, a burst-read transfer may not start with the first double word of the cache block
and the cache-block-fill operation may wrap around the end of the cache block. Table 8-5 describes
MPC8280 burst ordering.
Table 8-5. Burst Ordering
Double Word Starting Address:
Data Transfer
A[27–28] = 001
A[27–28] = 01
A[27–28] = 10
A[27–28] = 11
1st data beat
DW02
DW1
DW2
DW3
2nd data beat
DW1
DW2
DW3
DW0
3rd data beat
DW2
DW3
DW0
DW1
4th data beat
DW3
DW0
DW1
DW2
1
A[27–28] specifies the first double word of the 32-byte block being transferred; any subsequent double words must
wrap-around the block. A[29–31] are always 0b000 for burst transfers by the MPC8280.
2 DW x represents the double word that would be addressed by A[27–28] = x if a nonburst transfer were performed.
Each data beat is terminated with an assertion of TA.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
8-13
The 60x Bus
8.4.3.5
Effect of Alignment on Data Transfers
Table 8-6 lists the aligned transfers that can occur to and from the MPC8280. These are transfers in which
the data is aligned to an address that is an integer multiple of the size of the data. For example, Table 8-6
shows that 1-byte data is always aligned; however, a 4-byte word must reside at an address that is a
multiple of 4 to be aligned.
In Figure 8-6, Table 8-6, and Table 8-7, OP0 is the most-significant byte of a word operand and OP7 is the
least-significant byte.
Table 8-6. Aligned Data Transfers
Data Bus Byte Lanes
Program Transfer
Size
Byte
Half-Word
Word
Double-Word
TSIZ[0–3]
A[29–31]
D0...
...D31
D32...
...D63
B0
B1
B2
B3
B4
B5
B6
B7
0 0 0 1
000
OP01
—2
—
—
—
—
—
—
0 0 0 1
001
—
OP1
—
—
—
—
—
—
0 0 0 1
010
—
—
OP2
—
—
—
—
—
0 0 0 1
011
—
—
—
OP3
—
—
—
—
0 0 0 1
100
—
—
—
—
OP4
—
—
—
0 0 0 1
101
—
—
—
—
—
OP5
—
—
0 0 0 1
110
—
—
—
—
—
—
OP6
—
0 0 0 1
111
—
—
—
—
—
—
—
OP7
0 0 1 0
000
OP0
OP1
—
—
—
—
—
—
0 0 1 0
010
—
—
OP2
OP3
—
—
—
—
0 0 1 0
100
—
—
—
—
OP4
OP5
—
—
0 0 1 0
110
—
—
—
—
—
—
OP6
OP7
0 1 0 0
000
OP0
OP1
OP2
OP3
—
—
—
—
0 1 0 0
100
—
—
—
—
OP4
OP5
OP6
OP7
0 0 0 0
000
OP0
OP1
OP2
OP3
OP4
OP5
OP6
OP7
1
OPn: These lanes are read or written during that bus transaction. OP0 is the most-significant byte of a word operand
and OP7 is the least-significant byte.
2 —: These lanes are ignored during reads and driven with undefined data during writes.
The MPC8280 supports misaligned memory operations, although they may degrade performance
substantially. A misaligned memory address is one that is not aligned to the size of the data being
transferred (such as, a word read from an odd byte address). The MPC8280’s processor bus interface
supports misaligned transfers within a word (32-bit aligned) boundary, as shown in Table 8-7. Note that
the 4-byte transfer in Table 8-7 is only one example of misalignment. As long as the attempted transfer
does not cross a word boundary, the MPC8280 can transfer the data to the misaligned address within a
single bus transfer (for example, a half-word read from an odd byte-aligned address). It takes two bus
transfers to access data that crosses a word boundary.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
8-14
Freescale Semiconductor
The 60x Bus
Due to the performance degradation, misaligned memory operations should be avoided. In addition to the
double-word straddle boundary condition, the processor’s address translation logic can generate
substantial exception overhead when the load/store multiple and load/store string instructions access
misaligned data. It is strongly recommended that software attempt to align code and data where possible.
Table 8-7. Unaligned Data Transfer Example (4-Byte Example)
Data Bus Byte Lanes
Program Size of
Word (4 bytes)
TSIZ[1–3]
A[29–31]
D0...
...D31
D32...
...D63
B0
B1
B2
B3
B4
B5
B6
B7
Aligned
1 0 0
0 0 0
A1
A
A
A
—2
—
—
—
Misaligned—1st access
0 1 1
0 0 1
—
A
A
A
—
—
—
—
2nd access
0 0 1
1 0 0
—
—
—
—
A
—
—
—
Misaligned—1st access
0 1 0
0 1 0
—
—
A
A
—
—
—
—
2nd access
0 1 0
1 0 0
—
—
—
—
A
A
—
—
Misaligned—1st access
0 0 1
0 1 1
—
—
—
A
—
—
—
—
2nd access
0 1 1
1 0 0
—
—
—
—
A
A
A
—
Aligned
1 0 0
1 0 0
—
—
—
—
A
A
A
A
Misaligned—1st access
0 1 1
1 0 1
—
—
—
—
—
A
A
A
2nd access
0 0 1
0 0 0
A
—
—
—
—
—
—
—
Misaligned—1st access
0 1 0
1 1 0
—
—
—
—
—
—
A
A
2nd access
0 1 0
0 0 0
A
A
—
—
—
—
—
—
Misaligned—1st access
0 0 1
1 1 1
—
—
—
—
—
—
—
A
2nd access
0 1 1
0 0 0
A
A
A
—
—
—
—
—
1
2
A: Byte lane used
—: Byte lane not used
8.4.3.6
Effect of Port Size on Data Transfers
The MPC8280 can transfer operands through its 64-bit data port. If the transfer is controlled by the internal
memory controller, the MPC8280 can support 8-, 16-, 32-, and 64-bit data port sizes as demonstrated in
Figure 8-6. The bus requires that the portion of the data bus used for a transfer to or from a particular port
size be fixed. A 64-bit port must reside on data bus bits D[0–63], a 32-bit port must reside on bits D[0–31],
a 16-bit port must reside on bits D[0–15], and an 8-bit port must reside on bits D[0–7]. The MPC8280
always tries to transfer the maximum amount of data on all bus cycles: for a word operation, it always
assumes the port is 64 bits wide when beginning the bus cycle; for burst and extended byte cycles, a 64-bit
bus is assumed.
Figure 8-6. shows the device connections on the data bus. Table 8-8 lists the bytes required on the data bus
for read cycles.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
8-15
The 60x Bus
Interface Output Register
0
31
OP0
D[0–7]
OP0
OP1
OP2
D[8–15]
OP1
OP3
D[15–23]
OP2
D[24–31]
OP3
63
OP4
OP5
D[32–39]
OP4
OP6
D[40–47]
OP5
OP7
D[48–55]
OP6
D[56–63]
OP7
64-Bit Port Size
OP0
OP1
OP2
OP3
OP4
OP5
OP6
OP7
OP0
OP1
OP2
OP3
OP4
OP5
OP6
OP7
OP0
32-Bit Port Size
16-Bit Port Size
8-Bit Port Size
OP7
Figure 8-6. Interface to Different Port Size Devices
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
8-16
Freescale Semiconductor
The 60x Bus
Table 8-8. Data Bus: Read Cycle Requirements and Write Cycle Content
Port Size/Data Bus Assignments
Transfer
Size
TSIZ[0–3]
Address
State 1
A[29–31]
64-Bit
0–7
Byte
(0001)
Half Word
(0010)
Triple Byte
(0011)
32-Bit
8–15 16–23 24–31 32–39 40–47 48–55 56–63
2
—3
—
—
—
—
—
0–7
8–15
—
OP0
—
—
16-Bit
16–23 24–31
0–7
8–15
0–7
—
OP0
—
OP0
000
OP0
001
—
OP1
—
—
—
—
—
—
—
OP1
—
—
—
010
—
—
OP2
—
—
—
—
—
—
—
OP2
—
OP2
011
—
—
—
OP3
—
—
—
—
—
—
—
OP3
—
100
—
—
—
—
OP4
—
—
—
OP4
—
—
—
OP4
101
—
—
—
—
—
OP5
—
—
—
OP5
—
—
—
110
—
—
—
—
—
—
OP6
—
—
—
OP6
—
OP6
111
—
—
—
—
—
—
—
OP7
—
—
—
OP7
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
000
OP0 OP1
001
—
010
—
—
100
—
—
—
—
101
—
—
—
—
—
110
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
000
OP1 OP2
OP2 OP3
OP0 OP1 OP2
001
—
100
—
—
—
—
101
—
—
—
—
Word
(0100)
000
Double
Word
(0000)
000
100
OP1 OP2 OP3
OP0 OP1 OP2 OP3
OP4 OP5
OP5 OP6
OP6 OP7
OP4 OP5 OP6
—
—
OP5 OP6 OP7
—
—
OP5 OP6
—
—
OP6
OP0 OP1 OP2
—
OP1 OP2
OP4 OP5 OP6
—
OP5 OP6
OP3 OP3
—
OP4
OP5 OP5
—
OP6
OP7 OP7
OP0 OP1 OP0
—
OP1 OP1
OP3 OP2 OP3 OP2
—
—
OP4 OP5 OP4
—
OP5 OP5
OP7 OP6 OP7 OP6
—
OP3
—
OP7
OP0 OP1 OP0
—
OP1 OP1
OP4 OP5 OP4
—
OP5 OP5
OP7 OP4 OP5 OP4
OP0 OP1 OP2 OP3 OP4 OP5 OP6 OP7 OP0 OP1 OP2
OP3 OP0 OP1 OP0
—
—
OP4 OP5
OP2
OP2
OP4 OP5 OP6 OP7 OP4 OP5 OP6
—
—
—
—
—
OP3 OP0 OP1 OP0
—
—
OP1 OP2
OP1 OP1
OP0 OP1 OP2
—
—
—
OP0 OP1
8-Bit
1
Address state is the calculated address for port size.
OPn: These lanes are read or written during that bus transaction. OP0 is the most-significant byte of a word operand
and OP7 is the least-significant byte.
3
— These lanes are ignored during read cycles and driven with undefined data during write cycles.
2
8.4.3.7
60x-Compatible Bus Mode—Size Calculation
To comply with the requirements listed in Table 8-6 and Table 8-7, the transfer size and a new address must
be calculated at the termination of each beat of a port-size transaction. In single-MPC8280 bus mode, these
calculations are internal and do not constrain the system. In 60x-compatible bus mode, the external slave
or master must determine the new address and size. Table 8-9 describes the address and size calculation
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
8-17
The 60x Bus
state machine. Note that the address and size states are for internal use and are not transferred on the
address or TSIZ pins. Extended transactions (16- and 24-byte) are not described here but can be
determined by extending this table for 9-, 10-, 16-, 23-, and 24-byte transactions.
Table 8-9. Address and Size State Calculations
Size State
Port Size
Byte
x
x
x
x
x
x
2-Byte
x
x
x
x
0
Byte
x
x
0
0
x
x
1
x
x
x
3-Byte
Next Size State
Next Address State [0–4]
Stop
Byte
x
x
x
x
1
1
Byte
x
x
0
1
0
0
1
Byte
x
x
1
1
0
x
0
1
Byte
x
x
x
1
0
x
x
x
0
x
x
0
0
0
x
x
0
0
x
x
1
x
x
x
Half
Stop
2-Byte
x
x
0
0
1
1
2-Byte
x
x
0
1
0
0
0
2-Byte
x
x
1
0
1
1
0
1
2-Byte
x
x
1
1
0
x
0
0
0
Byte
x
x
0
1
0
x
x
0
0
1
2-Byte
x
x
0
1
0
x
x
1
0
0
Byte
x
x
1
1
0
x
x
1
0
1
2-Byte
x
x
1
1
0
x
x
x
x
x
Word
x
x
x
0
0
Byte
3-Byte
x
x
x
0
1
x
x
x
0
0
Half
2-Byte
x
x
x
1
0
x
x
x
x
x
Word
5-Byte
x
x
0
1
1
Byte
4-Byte
x
x
1
0
0
6-Byte
x
x
0
1
0
Byte
5-Byte
x
x
0
1
1
x
x
0
1
0
Half
4-Byte
x
x
1
0
0
7-Byte
x
x
0
0
1
Byte
6-Byte
x
x
0
1
0
8-Byte
x
x
0
0
0
Byte
7-Byte
x
x
0
0
1
x
x
0
0
0
Half
6-Byte
x
x
0
1
0
x
x
0
0
0
Word
4-Byte
x
x
1
0
0
x
x
0
0
0
Double
4-Byte
8.4.3.8
Address State [0–4]
Byte
Half
Stop
Stop
Stop
Extended Transfer Mode
The MPC8280 supports an extended transfer mode that improves bus performance. This should not be
confused with the extended bus protocol used to support direct-store operations supported in some earlier
processors that implement the PowerPC architecture. The MPC8280 can generate 5-, 6-, 7-, 16-, or 24-byte
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
8-18
Freescale Semiconductor
The 60x Bus
extended transfers. These transactions are compatible with the 60x bus, but some slaves or masters do not
support these features. Clear BCR[ETM] to disable this type of transaction. This places the MPC8280 in
strict 60x bus mode. The following tables are extensions to Table 8-7, Table 8-8, and Table 8-9.
Table 8-10 lists the patterns of the extended data transfer for write cycles when MPC8280 initiates an
access. Note that 16- and 24-byte transfers are always eight-byte aligned and use a 64-bit or less port size.
Table 8-10. Data Bus Contents for Extended Write Cycles
External Data Bus Pattern
Transfer
Size
TSIZ[0–3])
Address
State
A[29–31]
D[0–7]
D[8–15]
5 Bytes
(0101)
000
OP0
OP1
OP2
OP3
OP4
—
—
—
011
OP3
OP3
—
OP3
OP4
OP5
OP6
OP7
6 Bytes
(0110)
000
OP0
OP1
OP2
OP3
OP4
OP5
—
—
010
OP2
OP3
OP2
OP3
OP4
OP5
OP6
OP7
7 Bytes
(0111)
000
OP0
OP1
OP2
OP3
OP4
OP5
OP6
—
001
OP1
OP1
OP2
OP3
OP4
OP5
OP6
OP7
D[16–23] D[24–31] D[32–39] D[40–47] D[48–55] D[56–63]
Table 8-11 lists the bytes required on the data bus for extended read cycles. Note that 16- and 24-byte
transfers are always 8-byte aligned and use a maximum 64-bit port size.
Table 8-11. Data Bus Requirements for Extended Read Cycles
Port Size/Data Bus Assignments
Addres
Transfer
s State
Size
A[29-31
TSIZ[0–3]
]
5 Byte
(0101)
6 Byte
(0110)
7 Byte
(0111)
64-Bit
0–7
8–15
32-Bit
16–2
24–3
32–3
40–4
48–5
56–6
3
1
9
7
5
3
—
—
—
000
OP
0
OP OP2 OP3 OP4
1
011
—
—
000
OP
0
OP OP2 OP3 OP4 OP5
1
010
—
—
000
OP
0
OP OP2 OP3 OP4 OP5 OP6
1
001
—
OP OP2 OP3 OP4 OP5 OP6 OP7
1
—
OP3 OP4 OP5 OP6 OP7
—
—
OP2 OP3 OP4 OP5 OP6 OP7
—
0–7
8–15
16-Bit
16–2
24–3
3
1
0–7
8–15
8-Bit
0–7
OP
0
OP1
OP2 OP3 OP0 OP1 OP0
—
—
OP
0
OP1
OP2 OP3 OP0 OP1 OP0
—
—
OP2 OP3 OP2 OP3 OP2
OP
0
OP1
OP2 OP3 OP0 OP1 OP0
—
OP1
OP2 OP3
—
OP3
—
—
OP3 OP3
OP1 OP1
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
8-19
The 60x Bus
Table 8-12 includes added states to the transfer size calculation state machine. Only extended transfers use
these states.
Table 8-12. Address and Size State for Extended Transfers
Size State [0–3]
Half
3-Byte
Word
5-Byte
6-Byte
Address State[0–4]
Port Size
Next Size State [0–3]
Byte
Byte
x
x
x
1
1
x
x
1
0
1
x
x
x
x
x
Half
x
x
0
1
0
Byte
x
x
1
0
0
x
x
0
1
0
x
x
1
0
0
x
x
0
0
1
x
x
0
1
1
x
x
0
0
0
x
x
0
0
x
x
0
x
x
x
Next Address State[0–4]
x
x
1
0
0
x
x
1
1
0
x
x
0
1
1
x
x
1
0
1
x
x
1
0
0
x
x
1
1
0
x
x
0
1
0
x
x
1
0
0
x
x
0
0
1
1
x
x
0
1
0
1
0
x
x
0
1
1
0
1
1
x
x
1
0
0
x
0
0
0
x
x
0
1
0
x
x
0
1
0
x
x
1
0
0
x
x
0
1
1
Word
x
x
1
0
0
x
x
0
0
0
Byte
x
x
1
0
0
x
x
0
1
1
Word
x
x
1
0
0
x
x
x
x
x
Double
x
x
0
0
0
Byte
x
x
0
0
1
x
x
0
0
1
x
x
0
1
0
x
x
0
1
0
x
x
0
1
1
x
x
0
0
0
x
x
0
1
0
x
x
0
1
0
x
x
1
0
0
x
x
0
0
0
Half
x
x
1
0
0
x
x
0
1
0
Word
x
x
1
0
0
x
x
x
x
x
Half
Byte
Byte
Half
Word
Half
Word
Double
Stop
Half
Byte
3-Byte
Word
3-Byte
Stop
5-Byte
Word
Stop
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
8-20
Freescale Semiconductor
The 60x Bus
Table 8-12. Address and Size State for Extended Transfers (continued)
Size State [0–3]
7-Byte
Address State[0–4]
x
x
0
0
0
x
x
0
0
1
x
x
0
0
0
x
x
0
0
1
x
x
0
0
0
x
x
0
0
1
x
x
x
x
x
Port Size
Next Size State [0–3]
Byte
6-Byte
Half
Word
Double
Next Address State[0–4]
x
x
0
0
1
x
x
0
1
0
5-Byte
x
x
0
1
0
6-Byte
x
x
0
1
0
3-Byte
x
x
1
0
0
4-Byte
x
x
1
0
0
Stop
Extended transfer mode is enabled by setting the BCR[ETM].
8.4.4
Address Transfer Termination
Address transfer termination occurs with the assertion of the address acknowledge (AACK) signal, or
retried with the assertion of ARTRY. ARTRY must remain asserted until one clock after AACK; the bus
clock cycle after AACK is called the ARTRY window. The MPC8280 controls assertion of AACK unless
the cycle is claimed by an external slave, such as an external L2 cache controller. Following the assertion
of L2_HIT, the L2 cache controller is responsible for asserting AACK. When AACK is asserted by the
external slave, it should be asserted for one clock cycle and then negated for one clock cycle before
entering a high-impedance state. The MPC8280 holds AACK in a high-impedance state until it is required
to assert AACK to terminate the address cycle.
The MPC8280 uses AACK to enforce a pipeline depth of one to its internal slaves.
8.4.4.1
Address Retried with ARTRY
The address transfer can be terminated with the requirement to retry if ARTRY is asserted during the
address tenure and through the cycle following AACK. The assertion causes the entire transaction (address
and data tenure) to be rerun. As a snooping device, the MPC8280 processor asserts ARTRY for a snooped
transaction that hits modified data in the data cache that must be written back to memory, or if the snooped
transaction could not be serviced. As a bus master, the MPC8280 responds to an assertion of ARTRY by
aborting the bus transaction and requesting the bus again, as shown in Figure 8-7. Note that after
recognizing an assertion of ARTRY and aborting the current transaction, the MPC8280 may not run the
same transaction the next time it is granted the bus.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
8-21
The 60x Bus
CLKOUT
BR INT
BG INT
BR
External
BG
ABB
ADDR + ATTR
MPC8280
External
MPC8280
TS
AACK
ARTRY
Figure 8-7. Retry Cycle
As a bus master, the MPC8280 recognizes either an early or qualified ARTRY and prevents the data tenure
associated with the retried address tenure. If the data tenure has begun, the MPC8280 terminates the data
tenure immediately even if the burst data has been received. If the assertion of ARTRY is received up to
or on the bus cycle as the first (or only) assertion of TA for the data tenure, the MPC8280 ignores the first
data beat. If it is a read operation, the MPC8280 does not forward data internally to the cache, execution
unit, or any other MPC8280 internal storage. This address retry case succeeds because the data tenure is
aborted in time, and the entire transaction is rerun. This retry mechanism allows the memory system to
begin operating in parallel with the bus snoopers, provided external devices do not present data sooner than
the bus cycle before all snoop responses can be determined and asserted on the bus.
Note that the system must ensure that ARTRY is never asserted later than the cycle of the first or only
assertion of TA (if the PCI controller can initiate global transactions, the system must ensure that ARTRY
is never asserted on the same cycle or later then the first or only assertion of TA). This guarantees the
relationship between TA and ARTRY such that, in case of an address retry, the data may be cancelled in
the chip before it can be forwarded internally to the internal memory resources (registers or cache).
Generally, the memory system must also detect this event and abort any transfer in progress. If this
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
8-22
Freescale Semiconductor
The 60x Bus
TA/ARTRY relationship is not met, the master may enter an undefined state. Users may use
PPC_ACR[DBGD] to ensure correct operation of the system.
During the clock of a qualified ARTRY, each device master determines whether it should negate BR and
ignore BG on the following cycle. The following cycle is referred to as the window-of-opportunity for the
snooping master. During this window, only the snooping master that asserted ARTRY and requires a snoop
copyback operation is allowed to assert BR. This guarantees the snooping master a window of opportunity
to request and be granted the bus before the just-retried master can restart its transaction. BG is also
blocked in the window-of-opportunity, so the arbiter has a chance to negate BG to an already granted
potential bus master to perform a new arbitration.
Note that in some systems, an external processor may be unable to perform a pending snoop copyback
when a new snoop operation is performed. In this case, the MPC8280 requests the window of opportunity
if it hits on the new snooped address. To clear its internal snoop queue, it performs the snoop copyback
operation for the earlier snooped address instead of the current snooped address.
8.4.4.2
Address Tenure Timing Configuration
During address tenures initiated by 60x-bus devices, the timing of the assertion of AACK by the MPC8280
is determined by the BCR[APD] and the pipeline status of the 60x bus. Because the MPC8280 can support
one level of pipelining, it uses AACK to control the 60x-bus pipeline condition. To maintain the one-level
pipeline, AACK is not asserted for a pipelined address tenure until the current data tenure ends. The
MPC8280 also delays asserting AACK until no more address retry conditions can occur. Note that the
earliest the MPC8280 can assert AACK is the clock cycle when the wait-state values set by BCR[APD]
have expired.
BCR[APD] specifies the minimum number of address tenure wait states for address operations initiated
by 60x-bus devices. APD indicates how many cycles the MPC8280 should wait for ARTRY, but because
it is assumed that ARTRY can be asserted (by other masters) only on cacheable address spaces, APD is
considered only on transactions that hit a 60x-assigned memory controller bank and that have GBL
asserted during the address phase.
Extra wait states may occur because of other MPC8280 configuration parameters. Note that in a system
with an L2 cache, the number of wait states configured by BCR[APD] should be at least as large as the
value needed by the L2 controller to assert hit response. In systems with multiple potential masters, the
number of wait states configured by BCR[APD] should be at least as large as the value the slowest master
would need by to assert a snoop response. For example, additional wait states are required when the
internal processor is in 1:1 clock mode; this case requires at least one wait state to generate the ARTRY
response.
8.4.5
Pipeline Control
The MPC8280 supports the two following modes:
• One-level pipeline mode—To maintain the one-level pipeline, AACK is not asserted for a
pipelined address tenure until the current data tenure ends. In 60x-compatible bus mode, a
two-level pipeline depth can occur (for example, when an external 60x-bus slave does not support
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
8-23
The 60x Bus
•
8.5
one-level pipelining). When the internal arbiter counts a pipeline depth of two (two assertions of
AACK before the assertion of the current data tenure) it negates all address bus grant (BG) signals.
No-pipeline mode—The MPC8280 does not assert AACK until the corresponding data tenure
ends.
Data Tenure Operations
This section describes the operation of the MPC8280 during the data bus arbitration, transfer, and
termination phases of the data tenure.
NOTE: External Master Writes to DPRAM
DPRAM is clocked by the CPM clock and not by the 60x bus clock.
Therefore, data is not latched at the TA assertion cycle during writes to
DPRAM from the external master. Instead, the data is latched earlier. It is
necessary, then, that the external master drive the data bus immediately after
DBG and hold the data bus until after TA.
8.5.1
Data Bus Arbitration
The beginning of an address transfer, marked by the assertion of transfer start (TS), is also an implicit data
bus request provided that the transfer type signals (TT[0–4]) indicate that the transaction is not
address-only.
The MPC8280 arbiter supports one external master and uses DBG to grant the external master data
bus.The DBG signals are not asserted if the data bus, which is shared with memory, is busy with a
transaction.
A qualified data bus grant (QDBG) can be expressed as the assertion of DBG while DBB and ARTRY
(associated with the data bus operation) are negated.
Note that the MPC8280 arbiter should assert DBG only when it is certain that the first TA will be asserted
with or after the associated ARTRY. The MPC8280 DBG is asserted with TS if the data bus is free and if
the PPC_ACR[DBGD] = 0. If PPC_ACR[DBGD] = 1, DBG is asserted one cycle after TS if the data bus
is not busy. The DBG delay should be used to ensure that ARTRY is not asserted after the first or only TA
assertion. For the programming model, see Section 4.3.2.2, “60x Bus Arbiter Configuration Register
(PPC_ACR).”
Note that DBB should not be asserted after the data tenure is finished. Assertion of DBB after the last TA
causes improper operation of the bus. (MPC8280 internal masters do not assert DBB after the last TA.)
Note the following:
• External bus arbiters must comply with the following restriction on assertion of DBG which is
connected to the MPC8280. In case the data bus is not busy with the data of a previous transaction
on the bus, external arbiter must assert DBG in the same cycle in which TS is asserted (by a master
which was granted the bus) or in the following cycle. In case the external arbiter asserts DBG on
the cycle in which TS was asserted, PPC_ACR[DBGD] should be zero. Otherwise,
PPC_ACR[DBGD] should be set.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
8-24
Freescale Semiconductor
The 60x Bus
•
8.5.2
External masters connected to the 60x bus must assert DBB only for the duration of its data tenure.
External masters should not use DBB to prevent other masters from using the data bus after their
data tenure has ended.
Data Streaming Mode
The MPC8280 supports a special data streaming mode that can improve bus performance in some
conditions. Generally, the bus protocol requires one idle cycle between any two data tenures. This idle
cycle is essential to prevent contention on the data bus when the driver of the data is changing. However,
when the driver on the data bus is the same for both data tenures, this idle cycle may be omitted.
In data streaming mode, the MPC8280 omits the idle cycle where possible. MPC8280 applications often
require data stream transfers of more than 4 x 64 bits. For example, the ATM cell’s payload is 6 x 64 bits.
All this data is driven from a single device on the bus, so data-streaming saves a cycle for such a transfer.
When data-streaming mode is enabled, transactions initiated by the core are not affected, while
transactions initiated by other bus masters within the chip omit the idle cycle if the data driver is the same.
Note that data streaming mode cannot be enabled when the MPC8280 is in 60x-compatible bus mode and
a device that uses DBB is connected to the bus. This restriction is due to the fact that a MPC8280 for which
data streaming mode is enabled may leave DBB asserted after the last TA of a transaction and this is a
violation of the strict bus protocol. The data streaming mode is enabled by setting BCR[ETM].
8.5.3
Data Bus Transfers and Normal Termination
The data transfer signals include D[0–63] and DP[0–7]. For memory accesses, the data signals form a
64-bit data path, D[0–63], for read and write operations.
The MPC8280 handles data transfers in either single-beat or burst operations. Single-beat operations can
transfer from 1 to 24 bytes of data at a time. Burst operations always transfer eight words in four
double-word beats. A burst transaction is indicated by the assertion of TBST by the bus master. A
transaction is terminated normally by asserting TA.
The three following signals are used to terminate the individual data beats of the data tenure and the data
tenure itself:
• TA indicates normal termination of data transactions. It must always be asserted on the bus cycle
coincident with the data that it is qualifying. It may be withheld by the slave for any number of
clocks until valid data is ready to be supplied or accepted.
• Asserting TEA indicates a nonrecoverable bus error event. Upon receiving a final (or only)
termination condition, the MPC8280 always negates DBB for one cycle, except when fast data bus
grant is performed.
• Asserting ARTRY causes the data tenure to be terminated immediately if the ARTRY is for the
address tenure associated with the data tenure in operation (the data tenure may not be terminated
due to address pipelining). The earliest allowable assertion of TA depends directly on the latest
possible assertion of ARTRY.
Figure 8-8 shows both a single-beat and burst data transfer. The MPC8280 asserts TA to mark the cycle in
which data is accepted. In a normal burst transfer, the fourth assertion of TA signals the end of a transfer.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
8-25
The 60x Bus
CLKOUT
ADDR + ATTR
TS
AACK
DBG
TA
PSDVAL
D[0–63]
D0
D1
D2
D3
Figure 8-8. Single-Beat and Burst Data Transfers
8.5.4
Effect of ARTRY Assertion on Data Transfer and Arbitration
The MPC8280 allows an address tenure to overlap its associated data tenure. The MPC8280 internally
guarantees that the first TA of the data tenure is delayed to be at the same time or after the ARTRY window
(the clock after the assertion of AACK).
8.5.5
Port Size Data Bus Transfers and PSDVAL Termination
The MPC8280 can transfer data via data ports of 8, 16, 32, and 64 bits, as shown in Section 8.4.3, “Address
Transfer Attribute Signals.” Single-beat transaction sizes can be 8, 16, 32, 64, 128, and 192 bits; burst
transactions are 256 bits. Single-beat and burst transactions are divided into to a number of intermediate
beats depending on the port size. The MPC8280 asserts PSDVAL to mark the cycle in which data is
accepted. Assertion of PSDVAL in conjunction with TA marks the end of the transfer in single-beat mode.
The fourth assertion of PSDVAL in conjunction with TA signals the end of a burst transfer. Figure 8-9
shows an extended transaction of 4 words to a port size of 32 bits. The single-beat transaction is translated
to four port-sized beats.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
8-26
Freescale Semiconductor
The 60x Bus
CLKOUT
ADDR + ATTR
TS
AACK
DBG
PSDVAL
TA
D[0–31]
D0
D1
D2
D3
Figure 8-9. 28-Bit Extended Transfer to 32-Bit Port Size
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
8-27
The 60x Bus
Figure 8-10 shows a burst transfer to a 32-bit port. Each double-word burst beat is divided into two
port-sized beats such that the four double words are transferred in eight beats.
CLKOUT
ADDR + ATTR
TS
AACK
DBG
PSDVAL
TA
D[0–31]
D0
D1
D2
D3
D4
D5
D6
D7
Figure 8-10. Burst Transfer to 32-Bit Port Size
8.5.6
Data Bus Termination by Assertion of TEA
If a device initiates a transaction that is not supported by the MPC8280, the MPC8280 signals an error by
asserting TEA. Because the assertion of TEA is sampled by the device only during the data tenure of the
bus transaction, the MPC8280 ensures that the device master receives a qualified data bus grant by
asserting DBG before asserting TEA. The data tenure is terminated by a single assertion of TEA regardless
of the port size or whether the data tenure is a single-beat or burst transaction. This sequence is shown in
Figure 8-11.. In Figure 8-11. the data bus is busy at the beginning of the transaction, thus delaying the
assertion of DBG. Note that data errors (parity and ECC) are reported not by assertion of TEA but by
assertion of MCP.
Because the assertion of TEA is sampled by the device only during the data tenure of the bus transaction,
the MPC8280 ensures that the device receives a qualified data bus grant by asserting DBG before asserting
TEA. The data tenure is terminated by a single assertion of TEA regardless of the port size or whether the
data tenure is a single-beat or burst transaction.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
8-28
Freescale Semiconductor
The 60x Bus
This sequence is shown in Figure 8-11. In Figure 8-11 the data bus is busy at the beginning of the
transaction, thus delaying the assertion of DBG.
CLKOUT
ADDR + ATTR
For Single
For Burst
TS
AACK
DBG
TA
TEA
Data
Figure 8-11. Data Tenure Terminated by Assertion of TEA
The MPC8280 interprets the following bus transactions as bus errors:
• Direct-store transactions, as indicated by the assertion of XATS.
• Bus errors asserted by slaves (internal or external).
8.6
Memory Coherency—MEI Protocol
The MPC8280 provides dedicated hardware to ensure memory coherency by snooping bus transactions,
by maintaining information about the status of data in a cache block, and by the address retry capability.
Each data cache block includes status bits that support the modified/exclusive/invalid, or MEI,
cache-coherency protocol.
Asserting the global (GBL) output signal indicates whether the current transaction must be snooped by
other snooping devices on the bus. Address bus masters assert GBL to indicate that the current transaction
is a global access (that is, an access to memory shared by more than one device). If GBL is not asserted
for the transaction, that transaction is not snooped. When other devices detect the GBL input asserted, they
must respond by snooping any addresses broadcast. Normally, GBL reflects the M bit value specified for
the memory reference in the corresponding translation descriptor. Care must be taken to minimize the
number of pages marked as global, because the retry protocol discussed in the previous section used to
enforce coherency can require significant bus bandwidth.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
8-29
The 60x Bus
When the MPC8280 processor is not the address bus master, GBL is an input. The MPC8280 processor
snoops a transaction if TS and GBL are asserted together in the same bus clock cycle (a qualified snooping
condition). No snoop update to the MPC8280 processor cache occurs if the transaction is not marked
global. This includes invalidation cycles.
When the MPC8280 processor detects a qualified snoop condition, the address associated with the TS is
compared against the data cache tags. Snooping completes if no hit is detected. However, if the address
hits in the cache, the MPC8280 processor reacts according to the MEI protocol shown in Figure 8-12. This
figure assumes that WIM = 0b001 (memory space is marked for write-back, caching-allowed, and
coherency-enforced modes).
Invalid
SH/CRW
SH/CRW
WM
RM
WH
Modified
Exclusive
SH
RH
RH
WH
SH = Snoop hit
RH = Read hit
WH = Write hit
WM = Write miss
RM = Read miss
SH/CRW = Snoop hit, cacheable read/write
SH/CIR = Snoop hit, cache-inhibited read
SH/CIR
= Snoop push
= Cache line fill
Figure 8-12. MEI Cache Coherency Protocol—State Diagram (WIM = 001)
8.7
Processor State Signals
This section describes the MPC8280’s support for atomic update and memory through the use of the
lwarx/stwcx. instruction pair. It also describes the TLBISYNC input.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
8-30
Freescale Semiconductor
The 60x Bus
8.7.1
Support for the lwarx/stwcx. Instruction Pair
The load word and reserve indexed (lwarx) and the store word conditional indexed (stwcx.) instructions
provide a way to update memory atomically by setting a reservation on the load and checking that the
reservation is still valid before the store is performed. In the MPC8280, reservations are made on behalf
of aligned, 32-byte sections of the memory address space.
The reservation (RSRV) output signal is driven synchronously with the bus clock and reflects the status of
the reservation coherency bit in the reservation address register.
Note that each external master must do its own snooping; the MPC8280 does not provide external
reservation snooping.
8.7.2
TLBISYNC Input
The TLBISYNC input permits hardware synchronization of changes to MMU tables when the MPC8280
and another DMA master share the MMU translation tables in system memory. A DMA master asserts
TLBISYNC when it uses shared addresses that the MPC8280 could change in the MMU tables during the
DMA master’s tenure.
When the TLBISYNC input is asserted, the MPC8280 cannot complete any instructions past a tlbsync
instruction. Generally, during the execution of an eciwx or ecowx instruction, the selected DMA device
should assert the MPC8280’s TLBISYNC signal and hold it asserted during its DMA tenure if it is using
a shared translation address. Subsequent instructions by the MPC8280 processor should include a sync and
tlbsync instruction before any MMU table changes are performed. This prevents the MPC8280 from
making disruptive table changes during the DMA tenure.
8.8
Little-Endian Mode
The MPC8280 supports a little-endian mode in which low-order address bits are operated on (munged)
based on the size of the requested data transfer. This mode allows a little-endian program running on the
processor with a big-endian memory system to offset into a data structure and receive the same results as
it would if it were operating on a true little-endian processor and memory system. For example, writing a
word to memory as a word operation on the bus and then reading in the second byte of that word as a byte
operation on the bus.
NOTE
When the processor is selected for little-endian operation, the bus interface
is still operating in big-endian mode. That is, byte address 0 of a double
word (as selected by A[29–31] on the bus—after the internal address
munge) still selects the most significant (left most) byte of the double word
on D[0–7]. If the processor interfaces with a true little-endian environment,
the system may need to perform byte-lane swapping or other operations
external to the processor.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
8-31
The 60x Bus
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
8-32
Freescale Semiconductor
Chapter 9
PCI Bridge
The PCI bridge enables the MPC8280 to bridge PCI devices gluelessly to a processor that implements the
PowerPC architecture, to serve as a PCI interface for CompactPCI™ (CPCI) systems or as a basis for
passive PCI NIC implementations. In addition, multiple MPC8280 processors can interface with each
other over the PCI bus.
The key features of the PCI bridge are as follows:
• PCI Specification Revision 2.2 compliant and supports frequencies up to 66 MHz
• On-chip arbitration
• Support for PCI-to-60x-memory and 60x-memory-to-PCI streaming
• PCI host bridge or peripheral capabilities
• Includes 4 DMA channels for the following transfers:
— PCI-to-60x to 60x-to-PCI
— 60x-to-PCI to PCI-to-60x
— PCI-to-60x to PCI-to-60x
— 60x-to-PCI to 60x-to-PCI
• Includes all of the configuration registers required by the PCI standard as well as message and
doorbell registers
• Supports the I2O standard
• Hot-Swap friendly (supports the Hot Swap Specification as defined by PICMG 2.1 R1.0 August 3,
1998)
• Support for 66 MHz, 3.3 V specification
• Uses a buffer pool for the 60x-PCI bus interface
• Makes use of the local bus signals to avoid the need for additional pins
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-1
PCI Bridge
MPC8280
G2_LE Core
60x
Bus
PCI
Bridge
0
Mux
SDMA
Communications
Processor
DPRAM
Module
PCI
Bus
1
60x-to-Local
Bridge
PCI_MODE
Figure 9-1. PCI Bridge in the MPC8280
MPC8280 60x Bus/Local SDMA
MPC8280
Internal PCI Bridge
I/O Sequencer
60x Interface
Buffer
Pool
Embedded
Utilities
DMA
PCI Interface
I2O
Regs
PCI Bus
Figure 9-2. PCI Bridge Structure
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-2
Freescale Semiconductor
PCI Bridge
9.1
Signals
To avoid the need for additional pins, the PCI bridge is designed to make use of the local bus signals.
Therefore, many of these pins perform different functions, depending on how the user configures them.
PCI bridge signals are described in Chapter 6, “External Signals.”
9.2
Clocking
PCI bridge clocking is described in Chapter 10, “Clocks and Power Control.”
9.3
PCI Bridge Initialization
The PCI bridge uses fields from the hard reset configuration word (refer to Section 5.4.1, “Hard Reset
Configuration Word”) which are loaded during a hard reset (that is, assertion of the HRESET signal). This
section discusses PCI bridge initialization issues after reset.
The local bus pin configuration (LBPC) field of the hard reset configuration word should be programmed
to 0b01 so that the local bus operates as the PCI bus.
For PCI agent applications, the PCI_RST signal should be connected to the power-on reset (PORESET)
pin of the MPC8280. If the core is disabled, in PCI agent mode, an EEPROM must be provided for loading
the PCI configuration data.
For core-disabled, PCI agent applications, the communications processor (CP) can perform the minimal
initialization of the internal PCI bridge configuration registers required before responding to configuration
cycles. When the auto-load enable (ALD_EN) bit is set in the hard reset configuration word, the CP
automatically loads the PCI configuration data from the EPROM immediately following hard reset. (In
addition to the hard reset configuration word, the PCI configuration register data should be programmed
within the EPROM according to the port size. Refer to configuration register loading in Section 9.11.2.28,
“Initializing the PCI Configuration Registers,” for further details.) To prevent premature accesses,
CFG_LOCK (see Section 9.11.2.22, “PCI Bus Function Register”) is automatically set during hard reset
so that all attempted PCI accesses are retried. The user must re-enable PCI accesses by clearing
CFG_LOCK at the end of the PCI bridge initialization procedure.
In addition to the configuration register programming, several configuration pins are available in PCI
mode only. See Table 6-1 for a description of the external signals.
9.4
SDMA Interface
As shown in Figure 9-1, the PCI bridge has an interface to the SDMA controller. The CP can direct the
SDMA controller to bring data from the PCI bus memory/IO space into the dual-port RAM, or vice versa.
The user can choose if the data buffers, buffer descriptors, or any other needed data will reside on the 60x
bus or on the PCI bus. Because the PCI is replacing the local bus interface when PCI_MODE is active, the
PCI path is automatically chosen whenever the choice between 60x and local bus was programmed to
local. When the PCI bridge is disabled (PCI_MODE is negated), the SDMA transfers data to local memory
through the local bus interface whenever the choice is programmed to local. No change occurs when the
programmed option is the 60x bus. Refer to the descriptions of DTB and BIB in Table 31-16.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-3
PCI Bridge
NOTE
Although the user can direct the SDMA to the 60x bus, transactions can be
redirected to the PCI bridge if they fall in one of the PCI windows of the 60x
bus memory map (PCIBR0 or PCIBR1; refer to Section 4.3.4.1, “PCI Base
Register (PCIBRx)”). Data flow of this kind is not recommended because it
is not optimal. However, if it is implemented, the user must set strict 60x bus
mode (BCR[ETM] = 0).
9.5
Interrupts from PCI Bridge
Each of the PCI bridge interrupt sources—the PCI error condition detector, the DMA unit, and the message
unit—can generate an interrupt to the SIU interrupt controller. PCI bridge interrupts are reflected in
SIPNR_H[PCI] (refer to Section 4.3.1.4, “SIU Interrupt Pending Registers (SIPNR_H and SIPNR_L)”).
PCI bridge interrupts can be masked in general with SIMR_H[PCI] (refer to Section 4.3.1.5, “SIU
Interrupt Mask Registers (SIMR_H and SIMR_L)”). Specific interrupt sources can be masked
independently by masking the relevant bits in the following registers—error mask register, DMA mode
register, inbound message interrupt mask register, and the outbound message interrupt mask register. Each
of these registers is described in Section 9.11.1, “Memory-Mapped Configuration Registers.”
The interrupt service routine can determine the source of the interrupt by reading the status bits of the
following registers—the error status register, the DMA general status register, the inbound message
interrupt status register, and the outbound message interrupt status register.
For PCI interrupt vector calculation, refer to Section 4.2.4, “Interrupt Vector Generation and Calculation.”
For the priority of PCI interrupts, refer to Section 4.3.1.2, “SIU Interrupt Priority Register (SIPRR).”
9.6
60x Bus Arbitration Priority
To prevent 60x bus arbitration deadlock, the PCI bridge should be programmed to have a high arbitration
priority level within the 60x bus. The 60x bus arbitration-level register (PPC_ALRH) should be
programmed so that the PCI request level index (0b0011) has a priority higher than all other 60x bus
masters which address the PCI space through the 60x-PCI bridge (that is, the internal core or any external
masters). Masters which do not perform transactions in the PCI space (through the 60x-PCI bridge) can
have higher priority. Note that the default value of ALRH (0x0126_7893l) does not meet this requirement.
The same guidelines to prevent 60x bus arbitration deadlock apply to the programming of the parked
master. That is, program the parked master in the 60x bus arbiter configuration register
(PPC_ACR[PRKM]) to be the PCI bridge (0b0011); refer to Section 4.3.2.2, “60x Bus Arbiter
Configuration Register (PPC_ACR).”
9.7
60x Bus Masters
The number of external 60x bus masters allowed access to the PCI bridge is limited by the number of
pending requests that the PCI bridge is able to service. This number depends on the processor type of the
master. For example, up to two second generation (G2) processors that implement the PowerPC
architecture or three third generation (G3) processors can be accommodated.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-4
Freescale Semiconductor
PCI Bridge
9.8
CompactPCI Hot Swap Specification Support
CompactPCI is an open specification supported by the PCI Industrial Computer Manufacturers Group
(PICMG) and is intended for embedded applications using PCI. CompactPCI Hot Swap is an extension of
the CompactPCI specification and allows the insertion and extraction (or “hot swapping”) of boards
without adversely affecting system operation.
The Hot Swap specification defines three levels of support:
• Hot Swap capable
• Hot Swap friendly
• Hot Swap ready
The MPC8280 is a Hot Swap friendly device, meaning that it supports the hardware and software
connection processes as defined in the Hot Swap specification. This level of support allows the board and
system designers to build full Hot Swap and high availability systems based on the MPC8280 device as a
PCI target device. The only compliance exception is that the device pins are not 5-volt tolerant.
Application boards should be used in 3.3V signaling back planes, or add 5-to-3.3 volt signaling voltage
converters, if needed, to be used in 5V back planes.
For more information regarding the Hot Swap process, refer to the Hot Swap Specification PICMG 2.1,
R1.0, August 3, 1998.
9.9
PCI Interface
The PCI bridge connects the processor and memory system to the I/O components via the PCI system bus.
This interface acts as both initiator (master) and target (slave) device. The PCI bridge uses a 32-bit
multiplexed, address/data bus that can run at frequencies up to 66 MHz. The interface provides address
and data parity with error checking and reporting. The interface provides for three physical address
spaces—32-bit address memory, 32-bit address I/O, and PCI configuration space.
The PCI bridge can function as either a host bridge or an agent device. Note that the PCI bridge can be
configured from the PCI bus while in agent mode. An address translation mechanism is provided to map
PCI memory windows between the host and agent.
The following are the major features supported by the PCI interface:
• PCI Specification Revision 2.2 compliant
• On-chip arbitration supports 3 external PCI bus masters (in addition to the PCI bridge itself)
• Arbiter supports high-priority request and grant signal pairs
• Supports accesses to all PCI address spaces
• Supports PCI-to-60x-memory and 60x-memory-to-PCI streaming
• Memory prefetching of PCI read accesses and support for delayed read transactions
• Supports posting of processor to PCI and PCI to memory writes
• Supports selectable snoop
• PCI host bridge capabilities
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-5
PCI Bridge
•
•
PCI agent mode capabilities which include the ability to configure from a remote host
Address translation units for address mapping between host and agent.
Efforts were made to keep the terminology in this chapter consistent with the PCI Specification, revision
2.2, and other PCI documentation; therefore, the terms found in Table 9-1 may differ from most
documentation for processors that implement the PowerPC architecture (for example, architecture
specification or reference manuals).
Table 9-1. PCI Terminology
Term
Definition
LSB/Lower order
Represents bit 0 or the bits closest to the LSB
MSB/High order
Represents bit 31 or the bits closest to the MSB
Byte
Represents 8 bits of information
Word
Represents 16 bits or 2 bytes
Double word
Represents 32 bits or 2 words or 4 bytes
Quad word
Represents 64 bits or 2 double-words or 4 words or 8 bytes
Beat
Represents any valid data during a data transfer
Burst
Represents any 1 or more beat transfers
Edge/Clock edge
Represents the rising edge of the PCI clock
Cycle/Clock cycle
Represents the time period between clock edges
Asserted/negated
Represents the globally visible state of the signal on the clock edge
Address phase
Represents the first clock cycle where FRAME is asserted
Data phase(s)
Represents the clock cycle(s) where IRDY and TRDY are asserted
NOTE: PCI Bridge Signal Naming
PCI bridge signals are defined in most cases with the prefix “PCI_” (for
example, PCI_IRDY—see Figure 6-1). In this chapter, however, the prefix
is not used. For descriptions of PCI bridge signals, refer to Chapter 6,
“External Signals.”
9.9.1
PCI Interface Operation
The following sections discuss the operation of the PCI bus.
9.9.1.1
Bus Commands
PCI bus commands indicate the type of transaction occurring on the bus. These commands are encoded on
PCI_C/BE[3-0] during the address phase of the transaction. PCI bus commands are described in Table 9-2.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-6
Freescale Semiconductor
PCI Bridge
Table 9-2. PCI Command Definitions
Supported as:
PCI_C/BE[3-0]
Command Type
Definition
Initiator
Target
0b0000
Interrupt acknowledge
YES
NO
A read implicitly addressed to the system interrupt
controller. The size of the vector to be returned is
indicated on the byte enables after the address phase.
0b0001
Special cycle
YES
NO
Provides a simple message broadcast mechanism. See
Section 9.9.1.4.6, “Special Cycle Command.”
0b0010
I/O read
YES
NO
Accesses agents mapped in I/O address space.
0b0011
I/O write
YES
NO
Accesses agents mapped in I/O address space.
0b010x
—
—
—
Reserved. No response occurs.
0b0110
Memory read
YES
YES
Accesses agents mapped in memory address space. A
read from prefetchable space, when seen as a target,
fetches a cache line of data (32 bytes) from the starting
address, even though all 32 bytes may not actually be
sent to the initiator.
0b0111
Memory write
YES
YES
Accesses agents mapped in memory address space.
0b100x
—
—
—
0b1010
Configuration read
YES
YES
Accesses the configuration space of each agent. An
agent is selected when its IDSEL signal is asserted. See
Section 9.9.1.4.4, “Host Mode Configuration Access” for
more detail of configuration accesses. As a target, a
configuration read is only accepted if the PCI bridge is
configured to be in agent mode.
0b1011
Configuration write
YES
YES
Accesses the configuration space of each agent. An
agent is selected when its IDSEL signal is asserted. See
Section 9.9.1.4.4, “Host Mode Configuration Access”. As
a target, a configuration write is only accepted if the PCI
bridge is configured to be in agent mode.
0b1100
Memory read multiple
YES
YES
Causes a prefetch of the next cache line.
0b1101
Dual address cycle
NO
NO
Transfers an 8 byte address to devices.
0b1110
Memory read line
YES
YES
Indicates that the initiator intends to transfer an entire
cache line of data.
0b1111
Memory write and
invalidate
NO
YES
Indicates that the initiator will transfer an entire cache line
of data, and if PCI has any cacheable memory, this line
needs to be invalidated.
9.9.1.2
Reserved. No response occurs.
PCI Protocol Fundamentals
The bus transfer mechanism on the PCI bus is called a burst. A burst is comprised of an address phase and
one or more data phases.
All signals are sampled on the rising edge of the PCI clock. Each signal has a setup and hold window with
respect to the rising clock edge, in which transitions are not allowed. Outside this aperture, signal values
or transitions have no significance.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-7
PCI Bridge
9.9.1.2.1
Basic Transfer Control
PCI data transfers are controlled with three fundamental signals:
• FRAME is driven by an initiator to indicate the beginning and end of a transaction.
• IRDY (initiator ready) is driven by an initiator, allowing it to force wait cycles.
• TRDY (target ready) is driven by a target, allowing it to force wait cycles.
The bus is idle when both FRAME and IRDY are negated. The first clock cycle in which FRAME is
asserted indicates the beginning of the address phase. The address and the bus command code are
transferred in that cycle. The next cycle ends the address phase and begins the data phase.
During the data phase, data is transferred in each cycle that both IRDY and TRDY are asserted. Once the
PCI bridge, as an initiator, has asserted IRDY it does not change IRDY or FRAME until the current data
phase completes, regardless of the state of TRDY. Once the PCI bridge, as a target, has asserted TRDY or
STOP it does not change DEVSEL, TRDY, or STOP until the current data phase completes.
When the PCI bridge (as a master) intends to complete only one more data transfer, FRAME is negated
and IRDY is asserted (or kept asserted) indicating the initiator is ready. After the target indicates it is ready
(TRDY asserted) the bus returns to the idle state.
9.9.1.2.2
Addressing
The PCI specification defines three physical address spaces—memory, I/O, and configuration. The
memory and I/O address spaces are standard for all systems. The configuration address space has been
defined specifically to support PCI hardware configuration. Each PCI device decodes the address for each
PCI transaction with each agent responsible for its own address decode.
The information contained in the two lower address bits (AD1 and AD0) depends on the address space. In
the I/O address space, all 32 address/data lines provide the full byte address. AD[1-0] are used for the
generation of DEVSEL and indicate the least significant valid byte involved in the transfer. Once a target
has claimed an I/O access, it first determines if it can complete the entire access as indicated by the byte
enable signals. If all the selected bytes are not in the address range, the entire access should not be
completed; that is, the target should not transfer any data and should terminate the transaction with a
“target-abort” (refer to Section 9.9.1.3, “Bus Transactions”).
In the configuration address space, accesses are decoded to a double-word address using AD[7-2]. An
agent determines if it is the target of the access when a configuration command is decoded, IDSEL is
asserted, and AD[1-0] are 0b00; otherwise, the agent ignores the current transaction. The PCI bridge
determines a configuration access is for a device on the PCI bus by decoding a configuration command.
When in agent mode, the PCI bridge responds to host-generated PCI configuration cycles when its IDSEL
is asserted during a configuration cycle.
For memory accesses, the double-word address is decoded using AD[31–2]; thereafter, the address is
incremented internally by one double-word (4 bytes) until the end of the burst transfer. Another initiator
in a memory access should drive 0b00 on AD[1-0] during the address phase to indicate a linear
incrementing burst order. The PCI bridge checks AD[1-0] during a memory command access and provides
the linear incrementing burst order. On reads, if AD[1-0] is 0b10, which represents a cache line wrap, the
PCI bridge linearly increments the burst order starting at the critical word, wraps at the end of the cache
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-8
Freescale Semiconductor
PCI Bridge
line, and disconnects after reading one cache line. If AD[1-0] is 0bx1 (a reserved encoding) and the
PCI_C/BE[3-0] signals indicate a memory transaction, it executes a target disconnect after the first data
phase is completed. Note that AD[1-0] are included in parity calculations.
9.9.1.2.3
Byte Enable Signals
The byte enable signals (BE[3-0]) indicate which byte lanes carry valid data. The byte enable signals may
enable different bytes for each of the data phases. The byte enable signals are valid on the edge of the clock
that starts each data phase and remain valid for the entire data phase.
If the PCI bridge, as a target, sees no byte enable signals asserted, it completes the current data phase with
no permanent change. This implies that on a read transaction, the PCI bridge expects the data not to be
changed, and on a write transaction, the data is not stored.
9.9.1.2.4
Bus Driving and Turnaround
The turnaround-cycle is one clock cycle and is required to avoid contention. This cycle occurs at different
times for different signals. IRDY, TRDY, and DEVSEL use the address phase as their turnaround-cycle.
FRAME, PCI_C/BE[3-0], and AD[31-0] use the idle cycle between transactions as their turnaround-cycle.
(An idle cycle in PCI is when both FRAME and IRDY are negated.)
Byte lanes not involved in the current data transfer are driven to a stable condition even though the data is
not valid.
9.9.1.3
Bus Transactions
The timing diagrams in this section show the relationship of significant signals involved in bus
transactions.
Note the following conventions:
• When a signal is drawn as a solid line, it is actively being driven by the current initiator or target.
• When a signal is drawn as a dashed line, no agent is actively driving it.
• Three-stated signals with slashes between the two rails have indeterminate values.
• The terms ‘edge’ and ‘clock edge’ refer to the rising edge of the clock.
• The terms ‘asserted’ and ‘negated’ refer to the globally visible state of the signal on the clock edge,
and not to signal transitions.
• The symbol
represents a turnaround-cycle.
9.9.1.3.1
Read and Write Transactions
Both read and write transactions begin with an address phase followed by a data phase. The address phase
occurs when FRAME is asserted for the first time, and the AD[31-0] signals contain a byte address and
the PCI_C/BE[3-0] signals contain a bus command. The data phase consists of the actual data transfer and
possible wait cycles; the byte enable signals remain actively driven from the first clock of the data phase
through the end of the transaction.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-9
PCI Bridge
A read transaction starts when FRAME is asserted for the first time and the PCI_C/BE[3-0] signals
indicate a read command. Figure 9-3 shows an example of a single beat read transaction.
PCI_CLK
AD[31:0]
ADDR
PCI_C/BE[3:0]
CMD
DATA
BYTE ENABLES
FRAME
IRDY
DEVSEL
TRDY
Figure 9-3. Single Beat Read Example
Figure 9-4 shows an example of a burst read transaction.
PCI_CLK
AD[31:0]
ADDR
PCI_C/BE[3:0]
CMD
DATA1
BYTE ENABLES 1
DATA2
BYTE ENABLES 2
FRAME
IRDY
DEVSEL
TRDY
Figure 9-4. Burst Read Example
During the turnaround-cycle following the address phase, the PCI_C/BE[3-0] signals indicate which byte
lanes are involved in the data phase. The turnaround-cycle must be enforced by the target with the TRDY
signal if using fast DEVSEL assertion. The earliest the target can provide valid data is one cycle after the
turnaround-cycle. The target must drive the AD[31-0] signals when DEVSEL is asserted.
The data phase completes when data is transferred, which occurs when both IRDY and TRDY are asserted
on the same clock edge. When either is negated a wait cycle is inserted and no data is transferred. To
indicate the last data phase IRDY must be asserted when FRAME is negated.
A write transaction starts when FRAME is asserted for the first time and the PCI_C/BE[3-0] signals
indicate a write command. Figure 9-5 shows an example of a single beat write transaction.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-10
Freescale Semiconductor
PCI Bridge
PCI_CLK
AD[31:0]
ADDR
DATA
PCI_C/BE[3:0]
CMD
BYTE ENABLES
FRAME
IRDY
DEVSEL
TRDY
Figure 9-5. Single Beat Write Example
Figure 9-6 shows an example of a burst write transaction.
PCI_CLK
AD[31:0]
ADDR
DATA1
DATA2
DATA3
DATA4
PCI_C/BE[3:0]
CMD
BEs 1
BEs 2
BEs 3
BEs 4
FRAME
IRDY
DEVSEL
TRDY
Figure 9-6. Burst Write Example
A write transaction is similar to a read transaction except no turnaround cycle is needed following the
address phase because the initiator provides both address and data. Data phases are the same for both read
and write transactions.
9.9.1.3.2
Transaction Termination
The termination of a PCI transaction is orderly and systematic, regardless of the cause of the termination.
All transactions end when FRAME and IRDY are both negated, indicating the idle cycle.
The PCI bridge as an initiator terminates a transaction when FRAME is negated and IRDY is asserted. This
indicates that the final data phase is in progress. The final data transfer occurs when both TRDY and IRDY
are asserted. A master-abort is an abnormal case of an initiated termination. If the PCI bridge detects that
DEVSEL has remained negated for more than four clocks after the assertion of FRAME, it negates
FRAME and then, on the next clock, negates IRDY. On aborted reads, the PCI bridge returns
0xFFFF_FFFF. The data is lost on aborted writes.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-11
PCI Bridge
When the PCI bridge as a target needs to suspend a transaction, it asserts STOP. Once asserted, STOP
remains asserted until FRAME is negated. Depending on the circumstances, data may or may not be
transferred during the request for termination. If TRDY and IRDY are asserted during the assertion of
STOP, data is transferred. This type of target-initiated termination is called a ‘disconnect B,’ shown in
Figure 9-7. If TRDY is asserted when STOP is asserted but IRDY is not, TRDY must remain asserted until
IRDY is asserted and the data is transferred. This is called a “disconnect A” target-initiated termination,
also shown in Figure 9-7. However, if TRDY is negated when STOP is asserted, no more data is
transferred, and the initiator therefore does not have to wait for a final data transfer (see the ‘retry’ diagram
in Figure 9-7).
PCI_CLK
FRAME
IRDY
DEVSEL
TRDY
STOP
Disconnect A
Disconnect B
PCI_CLK
PCI_CLK
FRAME
FRAME
IRDY
IRDY
DEVSEL
DEVSEL
TRDY
TRDY
STOP
STOP
Latency disconnect
Retry
Target abort
Figure 9-7. Target-Initiated Terminations
Note that when an initiator is terminated by STOP, it must negate its REQx signal for a minimum of two
PCI clocks (of which one clock is needed for the bus to return to the idle state). If the initiator intends to
complete the transaction, it should reassert its REQx immediately following the two clocks or potential
starvation may occur. If the initiator does not intend to complete the transaction, it can assert REQx
whenever it needs to use the PCI bus again.
The PCI bridge terminates a transaction in the following cases:
• Eight PCI clock cycles have elapsed between data phases. This is a ‘latency disconnect’ (see
Figure 9-7).
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-12
Freescale Semiconductor
PCI Bridge
•
•
•
•
AD[1-0] is 0bx1 (a reserved burst ordering encoding) during the address phase and one data phase
has completed.
The PCI command is a configuration command and one data phase has completed when a
streaming transaction crosses a 4K page boundary.
A streaming transaction runs out of I/O sequencer buffer entries.
A cache line wrap transaction has completed a cache line transfer.
Another target-initiated termination is the retry termination. Retry refers to termination requested because
the target is currently in a state where it is unable to process the transaction. This can occur because no
buffer entries are available in the I/O sequencer, or the sixteen clock latency timer has expired without
transfer of the first data. The target latency timer of the PCI bridge can be optionally disabled see
Section 9.11.2.22, “PCI Bus Function Register.”
When the PCI bridge is in host mode it does not respond to any PCI configuration transactions. When the
PCI bridge is in agent mode and AGENT_CFG_LOCK is set (refer to Section 9.11.2.22, “PCI Bus
Function Register”) the PCI bridge will retry all configuration transactions. Note that all retried accesses
need to be completed. An example of a retry is shown in Figure 9-7.
Note that because a target can determine whether or not data is transferred (when both IRDY and TRDY
are asserted), if it wants to do only one more data transfer and then stop, it may assert TRDY and STOP at
the same time.
Target-abort refers to the abnormal termination that is used when a fatal error has occurred, or when a
target will never be able to respond. Target-abort is indicated by the fact that STOP is asserted and
DEVSEL is negated. This indicates that the target requires the transaction to be terminated and does not
want the transaction tried again. Note that any transferred data may have been corrupted.
The PCI bridge terminates a transaction with target-abort in the case in which it is the intended target of a
read transaction from system memory and the data from memory is corrupt. If the PCI bridge is the
intended target of a transaction and an address parity error occurs, or a data parity error occurs on a write
transaction to system memory, it continues the transaction on the PCI bus but aborts internally. The PCI
bridge does not target-abort in this case.
If the PCI bridge is mastering a transaction and the transaction terminates with a target-abort, undefined
data will be returned on a read and write data will be lost. An example of a target-abort is shown in
Figure 9-7.
An initiator may retry any target disconnect accesses, except target-abort, at a later time starting with the
address of the next non-transferred data. Retry is actually a special case of disconnect where no data
transfer occurs at all and the initiator must start the entire transaction over again.
9.9.1.4
Other Bus Operations
The following sections provide information on additional PCI bus operations.
9.9.1.4.1
Device Selection
As a target, the PCI bridge drives DEVSEL one clock following the address phase as indicated in the
configuration space status register; see Section 9.11.2.4, “PCI Bus Status Register.” The PCI bridge as a
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-13
PCI Bridge
target qualifies the address/data lines with FRAME before asserting DEVSEL. DEVSEL is asserted at or
before the clock edge at which the PCI bridge enables its TRDY, STOP, or data (for a read). DEVSEL is
not negated until FRAME is negated, with IRDY asserted and either STOP or TRDY asserted. The
exception to this is a target-abort; see Section 9.9.1.3.2, “Transaction Termination.”
As an initiator, if the PCI bridge does not see the assertion of DEVSEL within 4 clocks of FRAME, it
terminates the transaction with a master-abort as described in Section 9.9.1.3.2, “Transaction
Termination.”
9.9.1.4.2
Fast Back-to-Back Transactions
In the two types of fast back-to-back transactions, the first type places the burden of avoiding contention
on the initiator while the second places the burden on all potential targets. The PCI bridge as a target
supports both types of fast back-to-back transactions but does not support them as an initiator. The PCI
bridge as a target has the fast back-to-back enable bit hardwired to one, or enabled; see Table 9-18.
For the first type (governed by the initiator), the initiator may only run a fast back-to-back transaction to
the same target. For the second type, when the PCI bridge detects a fast-back-to-back operation and did
not drive DEVSEL in the previous cycle, it delays the assertion of DEVSEL and TRDY for one cycle to
allow the other target to get off the bus.
9.9.1.4.3
Data Streaming
The PCI bridge provides data streaming for PCI transactions to and from prefetchable memory. In other
words, when the PCI bridge is a target for a PCI initiated transaction, it supplies or accepts multiple cache
lines of data without disconnecting. For PCI transactions to non-prefetchable space, the PCI bridge
disconnects after the first data phase so that no streaming can occur.
For PCI memory reads, streaming is achieved by performing speculative reads from memory in
prefetchable space. A block of memory can be marked as prefetchable by setting the prefetch bit in the
corresponding inbound ATU (see Table 9-18) in the following cases:
• When reads do not alter the contents of memory (reads have no side effects)
• When reads return all bytes regardless of the byte enable signals
• When writes can be merged without causing errors
For a memory read command or a memory read line command, the PCI bridge reads one cache line from
memory. If the PCI read or read line transaction crosses a cache line boundary, the PCI bridge starts the
read of a new cache line. For a memory read multiple command, the PCI bridge reads two cache lines from
memory. When the PCI transaction finishes the read for the first cache line, the PCI bridge performs a
speculative read of a third cache line. The PCI bridge continues this prefetching until the end of the
transaction.
For PCI writes to memory, streaming is achieved by buffering the transaction in the space available within
the I/O sequencer. This allows PCI memory writes to execute with no wait states.
A disconnect occurs if the PCI bridge runs out of buffer space on writes, or the PCI bridge cannot supply
consecutive data beats for reads within eight PCI bus clocks of each other. A disconnect also occurs if the
transaction crosses a 4K page boundary.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-14
Freescale Semiconductor
PCI Bridge
For core- or DMA-initiated transfers, the PCI bridge streams over cache line boundaries if the prefetch bit
in the corresponding outbound ATU is enabled and the address space identified by the outbound ATU is
marked as PCI memory space.
9.9.1.4.4
Host Mode Configuration Access
The PCI bridge provides two types of configuration accesses to support hierarchical bridges. To access
configuration space, a value is written to the CONFIG_ADDR register specifying which PCI bus, which
device, and which configuration register to be accessed.
When the PCI bridge sees an access that falls inside the double-word beginning at the CONFIG_DATA
address, it checks the enable bit, the device number and the bus number in the CONFIG_ADDR register.
If the enable bit is set and the device number is not equal to all ones, a configuration cycle translation is
performed. When the device number field is equal to all ones, it has a special meaning (see
Section 9.9.1.4.6, “Special Cycle Command”).
The format of CONFIG_ADDR is shown in Figure 9-8. Bits 23 through 16 choose a specific PCI bus in
the system. Bits 15 through 11 choose a specific device on the bus. Bits 10 through 8 choose a specific
function in the requested device. Bits 7 through 2 choose a DWORD in the device’s configuration space.
Bit 31 is an enable flag for determining when accesses to CONFIG_DATA should be translated to
configuration cycles.
31 30
E
24 23
—
16 15
Bus number
31
11 10
Device number
8
7
Function
number
2
Register number
11 10
Only one bit is set at a time (for IDSEL)
2
Function register
1
0
0
0
1
0
0
0
Figure 9-8. PCI Configuration Type 0 Translation
(Top = CONFIG_ADDR) (Bottom = PCI Address Lines)
There are two types of translations supported:
• Type 0 translations—For when the device is on the PCI bus connected to the PCI bridge.
(Figure 9-8 shows the Type 0 translation from the CONFIG_ADDR register to the address/data
lines on the PCI bus.)
• Type 1 translations—For when the device is on another bus somewhere behind the PCI bridge.
For Type 0 translations, the PCI bridge decodes the device number field to assert the appropriate IDSEL
line and perform a configuration cycle on the PCI bus with AD[1-0] as 0b00. All 21 IDSEL bits are
decoded, starting with bit AD[11]. That is, if the device number field contains 0b01011, AD[11] on the
PCI bus is set. The IDSEL lines are bit-wise associated with increasing values for the device number such
that AD[12] corresponds to 0b01100, and so on up to bit 30. AD[31] is selected with 0b01010. A device
number of 0b11111 indicates a special cycle. Device number 0b00000 is used for configuring the PCI
bridge itself. Bits 10 through 8 are copied to the PCI bus as an encoded value for components which
contain multiple functions. Bits 7 through 2 are also copied onto the PCI bus. The PCI bridge implements
address stepping on configuration cycles so that the target’s IDSEL, which is connected directly to one of
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-15
PCI Bridge
the AD lines, reaches a stable value. This means that a valid address and command are driven on the AD
and PCI_C/BE lines one cycle before the assertion of FRAME.
For Type 1 translations, the PCI bridge copies the contents of the CONFIG_ADDR register directly onto
the PCI address/data lines during the address phase of a configuration cycle, with the exception that
AD[1-0] contains 0b01 (not 0b00 as in Type 0 translations).
NOTE
Due to design constraints, the software must write a value to the
CONFIG_ADDR register prior to each access to the CONFIG_DATA
register, even if the address was not changed.
When the MPC8280 is configured as a host device, it sometimes needs to perform configuration reads
from unpopulated PCI slots (as part of the system configuration). To avoid getting a machine check
interrupt, the following steps should be taken:
1. Mask the “PCI No response” bit in the error mask register (clear bit 3). Refer to Section 9.11.1.9,
“Error Status Register (ESR).”
2. Make the PCI configuration reads.
3. Clear bit 3 in the error status register (by writing 0x08).
4. Unmask (write'1') bit 3 in the error mask register. Refer to Section 9.11.1.10, “Error Mask Register
(EMR).”
9.9.1.4.5
Agent Mode Configuration Access
When the PCI bridge is configured as an agent device, it responds to remote host generated PCI
configuration accesses to the PCI interface. This is indicated by decoding the configuration command
along with the PCI bridge's IDSEL being asserted. A remote host can access the 256-byte PCI
configuration area (Figure 9-32) and the memory-mapped configuration registers within the PCI bridge.
9.9.1.4.6
Special Cycle Command
A special cycle command contains no explicit destination address but is broadcast to all PCI agents. Each
receiving agent must determine whether the message is applicable to itself. No assertion of DEVSEL in
response to a special cycle command is necessary.
A special cycle command is like any other bus command in that it has an address phase and a data phase.
The address phase starts like all other commands with the assertion of FRAME and completes when
FRAME and IRDY are negated. Special cycles terminate with a master-abort. (In the special cycle case,
the received-master-abort bit in the configuration status register is not set.)
The address phase contains no valid information other than the command field. Even though there is no
explicit address, the address/data lines are driven to a stable state and parity is generated. During the data
phase, the address/data lines contain the message type and an optional data field. The message is encoded
on the sixteen least-significant bits (AD[15-0]). The data field is encoded on AD[31-16]. When running a
special cycle, the PCI bridge can insert wait states, but because no specific target is addressed, the message
and data are valid on the first clock IRDY is asserted.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-16
Freescale Semiconductor
PCI Bridge
When the CONFIG_ADDRESS register gets written with a value such that the bus number matches the
bridge’s bus, the device number is all ones, the function number is all ones and the register number is zero,
the next time the CONFIG_DATA register is accessed the PCI bridge does either a special cycle or an
interrupt acknowledge command. When the CONFIG_DATA register is written, the PCI bridge generates
a special cycle encoding on the command/byte enable lines during the address phase, and drives the data
from the CONFIG_DATA register onto the address/data lines during the first data phase.
If the bus number field of the CONFIG_ADDRESS does not match one of the PCI bridge’s bus numbers,
the PCI bridge passes the write to CONFIG_DATA on through to the PCI bus as a type 1 configuration
cycle like any other time the bus number field does not match.
9.9.1.4.7
Interrupt Acknowledge
When the CONFIG_ADDRESS register gets written with a value such that the bus number is 0x00, the
device number is all ones, the function number is all ones and the register number is zero, the next time
the CONFIG_DATA register is accessed the PCI bridge does either a special cycle command or an
interrupt acknowledge command. When the CONFIG_DATA register is read, the PCI bridge generates an
interrupt acknowledge command encoding on the command/byte enable lines during the address phase.
During the address phase, AD[31-0] do not contain a valid address but are driven with stable data and valid
parity (PAR). During the data phase, the byte enable signals determine which bytes are involved in the
transaction. The interrupt vector must be returned when TRDY is asserted.
An interrupt acknowledge transaction can also be issued on the PCI bus by reading from the
PCI_INT_ACK register.
9.9.1.5
Error Functions
This section discusses PCI bus errors.
9.9.1.5.1
Parity
During valid 32-bit address and data transfers, parity covers all 32 address/data lines and the 4
command/byte enable lines regardless of whether or not all lines carry meaningful information. Byte lanes
not actually transferring data are driven with stable (albeit meaningless) data and are included in the parity
calculation. During configuration, special cycle or interrupt acknowledge commands, some address lines
are not defined but are still driven to stable values and included in the parity calculation.
Even parity is calculated for all PCI operations: the value of PAR is generated such that the number of ones
on AD[31-0], PCI_C/BE[3-0] and PAR equals an even number. PAR is driven when the address/data lines
are driven and follow the corresponding address or data by one clock.
The PCI bridge checks the parity after all valid address phases (the assertion of FRAME) and for valid data
transfers (IRDY and TRDY asserted) involving the PCI bridge. When an address or data parity error is
detected, the detected-parity-error bit in the configuration space status register is set (see Section 9.11.2.4,
“PCI Bus Status Register”).
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-17
PCI Bridge
9.9.1.5.2
Error Reporting
Except for setting the detected-parity-error bit, all parity error reporting and response is controlled by the
parity-error-response bit (see Section 9.11.2.3, “PCI Bus Command Register”). If the
parity-error-response bit is cleared, the PCI bridge completes all transactions regardless of parity errors
(address or data). If the bit is set, the PCI bridge asserts PERR two clocks after the actual data transfer in
which a data parity error is detected, and keeps PERR asserted for one clock. The PCI bridge asserts PERR
when acting as an initiator during a read transaction or as a target involved in a write to system memory.
Figure 9-9 shows the possible assertion points for PERR if the PCI bridge detects a data parity error.
PCI_CLK
AD[31:0]
ADDR
PCI_C/BE[3:0]
CMD
DATA
BEs
ADDR
DATA
CMD
BEs
PAR
FRAME
IRDY
DEVSEL
TRDY
PERR
SERR
Figure 9-9. PCI Parity Operation
As an initiator, the PCI bridge attempts to complete the transaction on the PCI bus if a data parity error is
detected and sets the data-parity-reported bit in the configuration space status register. If a data parity error
occurs on a read transaction, the PCI bridge aborts the transaction internally. As a target, the PCI bridge
completes the transaction on the PCI bus even if a data parity error occurs. If parity error occurs during a
write to system memory, the transaction completes on the PCI bus but is aborted internally, insuring that
potentially corrupt data does not go to memory.
When the PCI bridge asserts SERR, it sets the signaled-system-error bit in the configuration space status
register. Additionally, if the error is an address parity error, the parity-error-detected bit is set; reporting an
address parity error on SERR is conditioned on the parity-error-response bit being enabled in the command
register. SERR is asserted when the PCI bridge detects an address parity error while acting as a target. The
system error is passed to the PCI bridge’s interrupt processing logic to assert MCP. Figure 9-9 shows where
the PCI bridge could detect an address parity error and assert SERR or where the PCI bridge, acting as an
initiator, checks for the assertion of SERR signaled by the target detecting an address parity error.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-18
Freescale Semiconductor
PCI Bridge
As a target that asserts SERR on an address parity, the PCI bridge completes the transaction on the PCI
bus, aborting internally if the transaction is a write to system memory. If PERR is asserted during a PCI
bridge write to PCI, the PCI bridge attempts to continue the transfer, allowing the target to abort/disconnect
if desired. If the PCI bridge detects a parity error on a read from PCI, the PCI bridge aborts the transaction
internally and continues the transfer on the PCI bus, allowing the target to abort/disconnect if desired.
In all cases of parity errors on the PCI bus, regardless of the parity-error-response bit, information about
the transaction is logged in the PCI error control capture register, the PCI error address capture register and
the PCI error data capture register; MCP is also asserted to the core as an option.
9.9.2
PCI Bus Arbitration
The PCI bus arbitration approach is access-based. Bus masters must arbitrate for each access performed
on the bus. PCI uses a central arbitration scheme where each master has its own unique request (REQx)
output and grant (GNTx) input signal. A simple request-grant handshake is used to gain access to the bus.
Arbitration for the bus occurs during the previous access so that no PCI bus cycles are consumed waiting
for arbitration (except when the bus is idle).
The PCI bridge provides arbitration for three external PCI bus masters (besides the PCI bridge itself) by
using the REQ0, REQ1, and REQ2 signals and generating the GNT0, GNT1, and GNT2 signals.
During reset, the PCI bridge samples the PCI_CFG[1] pin (and programs the PCI_ARB_DIS bit
accordingly) to determine if the arbiter is enabled or disabled. The arbiter can also be enabled or disabled
by directly programming the PCI_ARB_DIS bit in the arbiter configuration register (see
Section 9.11.2.23, “PCI Bus Arbiter Configuration Register”).
If the arbiter is disabled, the PCI bridge uses REQ0 to issue requests to an external arbiter, and uses GNT0
to receive grants from the external arbiter.
The PCI bridge implements a two-level priority, round-robin arbitration algorithm. The priority level for
the different masters can be programmed in the arbiter configuration register (see Section 9.11.2.23, “PCI
Bus Arbiter Configuration Register”).
9.9.2.1
Bus Parking
When no devices are requesting the bus, the bus is granted, or parked, for a specified device to prevent the
AD, PCI_C/BE and PAR signals from floating. The PCI bridge can be configured to either park on the PCI
bridge or park on the last master to use the bus by programming the parking-mode bit in the arbiter
configuration register (see Section 9.11.2.23, “PCI Bus Arbiter Configuration Register”).
9.9.2.2
Arbitration Algorithm
The arbitration algorithm implemented is round-robin with two priority levels. Each of the three external
PCI bus masters, plus the PCI bridge, are assigned either a high or a low priority level, as programmed in
the arbiter configuration register (see Section 9.11.2.23, “PCI Bus Arbiter Configuration Register”).
Within each priority group (high or low), the bus grant is given to the next requesting device in numerical
order, with the PCI bridge itself positioned before device 0. GNTx is asserted for device x as soon as the
previously granted device begins a transaction. Conceptually, the lowest priority device at any given time
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-19
PCI Bridge
is the master that is currently using the bus, and the highest priority device is the next one to follow the
current master. This is considered to be a fair algorithm because a given device cannot prevent other
devices from having access to the bus—a given device automatically becomes the lowest priority device
as soon as it begins to use the bus. If a master is not requesting the bus, the transaction slot is given to the
next requesting device within the priority group.
The grant given to a particular device may be taken away and given to another, higher priority device
whenever the higher priority device asserts its request. If the bus is idle when a new device is to receive a
grant, no device receives a grant for one clock and then in the next clock, the new winner of the arbitration
receives a grant. This operation allows for a turnaround clock when a device is using address stepping or
when the bus is parked.
The low priority group collectively receives one bus transaction request slot in the high priority group.
Therefore, if there are N high-priority devices, each high-priority device is guaranteed to get at least one
of (N+1) bus transactions, and the M low priority devices are guaranteed to each get at least one of (N+1)
x M bus transactions, with one of the low-priority devices receiving the grant in one of (N+1) bus
transactions. If all devices are programmed to the same priority level or if there is only one device at the
low priority, the algorithm provides each device an equal number of bus grants in a round-robin sequence.
An arbitration example with three masters in the high priority group and two in the low priority group is
shown in Figure 9-10. Noting that one position in the high priority group is actually a placeholder for the
low priority group, it can be seen that each high priority initiator is guaranteed at least 1 out of 3 transaction
slots, and each low priority initiator is guaranteed at least 1 out of 6 slots. Assuming all devices are
requesting the bus, the grant sequence (with device 1 being the current master) is as follows: 0, 2, the PCI
bridge, 0, 2, 1, 0, 2, the PCI bridge, and so on. If, for example, device 2 is not requesting the bus, the grant
sequence becomes 0, the PCI bridge, 0, 1, 0, the PCI bridge, and so on. If device 2 now requests the bus
at a point in the sequence when device 0 is conducting a transaction and the PCI bridge is the next grant,
then the PCI bridge’s grant is removed, and the higher-priority device 2 is awarded the next grant.
e
High priority group
Low priority group
2
(1/3)
1
(1/6)
0
(1/3)
Low
(1/3)
PCI
bridge
(1/6)
Figure 9-10. PCI Arbitration Example
9.9.2.3
Master Latency Timer
The PCI bridge implements the master latency timer register (see Section 9.11.2.10, “PCI Bus Latency
Timer Register”) to prevent the itself from monopolizing the bus. When the master latency timer expires,
the PCI bridge checks the state of its GNT signals. If the GNT signal is not asserted, the PCI bridge
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-20
Freescale Semiconductor
PCI Bridge
completes one more data phase and relinquishes the bus. The master latency timer can be disabled if
needed (see Section 9.11.2.22, “PCI Bus Function Register”).
9.10
Address Map
A transaction sent to the PCI bridge from any 60x bus master side falls into one of the following three
cases:
• If the transaction address is within the internal register space of the MPC8280, the transaction is
handled by the PCI bridge internal register logic. (The internal registers are described in this
chapter.)
• If the transaction address is within one of the three outbound PCI translation windows (described
in this chapter), the transaction is sent to the PCI bus with address translation.
• If the transaction address is not within the internal register space and not within a PCI translation
window, the transaction is sent to the PCI bus with no address translation as a PCI memory
transaction to non-prefetchable space.
An address decode flow chart for transactions from the 60x bus masters to the PCI bridge is shown in
Figure 9-11.
60x bus mastered
transaction
Hit
IMMR
?
No
Yes
Hit PCI
internal registers
? (1)
Hit
PCIBR0/PCIBR1
?
No
Hit
Outbound ATU
?
No
No
Yes
Yes
Execute register
access to
PCI interface
internal registers
Yes
Translate the
address
Issue transaction
with un-translated
address to PCI
No action
(1): IMMR+0x10400 ≤ addr ≤ IMMR+0x10bff
Issue transaction
with translated
address to PCI
Figure 9-11. Address Decode Flow Chart for 60x Bus Mastered Transactions
Transactions directed to the MPC8280 from a PCI bus master are handled as follows:
• If the transaction address is within the internal register space of the MPC8280, the transaction is
either handled by the PCI bridge internal register logic or forwarded to the core side of the PCI
bridge to be handled by the MPC8280 internal register logic as appropriate.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-21
PCI Bridge
•
If the transaction address is within one of the two inbound PCI translation windows, the transaction
is sent to the core side of the PCI bridge with address translation.
This window is provided for the PCI master to access the MPC8280's
internal (dual port) registers/area. Its size is assumed to be fixed at 128K
bytes. It translates to the MPC8280's IMMR value for the upper bits of the
address. This way, the PCI master can access any of the PCI bridge registers
(DMA/MU, etc.) without wasting an inbound translation window. In effect,
it suggests that we have a total of three inbound windows, 2 with ATUs and
one with PIMMR.
An address decode flow chart for transactions from a PCI bus master to the PCI bridge is shown in
Figure 9-12.
PCI mastered
transaction
Hit
Inbound ATU
?
Hit
PIMMR
?
No
Yes
No
Yes
No DEVSEL
Translate the
address
Hit
IMMR
?
No
Yes
Hit PCI
internal registers
? (1)
Yes
Issue transaction
to 60x bus
No
(1): IMMR+0x10400 ≤ addr ≤ IMMR+0x10bff
Execute register
access to
PCI interface
internal registers
Figure 9-12. Address Decode Flow Chart for PCI Mastered Transactions
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-22
Freescale Semiconductor
PCI Bridge
NOTE
When a transaction is performed by a PCI master, the bridge checks the
address against inbound ATUs and if it does not hit, it then checks against
PIMMR; if it is a hit, the bridge translates it to a 60x cycle. Because PIMMR
does not have an associated translation register and window size definition,
the translation is performed as follows: a 128-Kbyte window is provided for
the PCI master to access the MPC8280’s internal (dual port) registers. It
translates to the MPC8280’s IMMR value for the upper bits of the address.
This allows the PCI master to access any of the PCI-bridge registers without
wasting an inbound translation window. In effect, there are a total of three
inbound windows, 2 with ATUs and 1 with PIMMR.
Transactions initiated by the DMA controller or message unit fall into one of the following cases:
• If the transaction address is within one of the outbound PCI translation windows, the transaction is
sent to the PCI bus with address translation.
• If the transaction address is not within a PCI translation window, the transaction is sent to the core
side of the PCI bridge with no address translation.
An address decode flow chart for transactions from the DMA controller or message unit to the PCI bridge
is shown in Figure 9-13.
DMA/MU mastered
transaction
Hit
Outbound ATU
?
No
Yes
Issue transaction
with translated
address to PCI
Issue transaction
with un-translated
address to 60x bus
Figure 9-13. Address Decode Flow Chart for Embedded Utilities
(DMA, Message Unit) Mastered Transactions
Example address mappings of these different types of transactions are shown in Figure 9-14. Note that the
translation mechanism shown is an example only; the address translation, as well as the memory and I/O
destinations, can be programmed independently for each address translation window.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-23
PCI Bridge
60x bus master view
PCI master memory view
0
0
PCI master I/O view
0
Address translation
Address translation
Address translation
PCI bridge
Address translation
PCI memory
Address translation
Internal registers
Internal registers
4G
4G
4G
Figure 9-14. Address Map Example
9.10.1
Address Map Programming
The address map has a number of programmable ranges to determine the PCI bridge’s response to all
transactions. The following are the PCI bridge’s rules for programming each address range:
• All address regions should not overlap but do not have to be contiguous.
• All address ranges must be aligned on a multiple of the region size.
• Inbound and outbound windows for the same bus should not overlap. This means that a situation
where an inbound window translation points back into an outbound window, or a situation where
an outbound translation window points back into an inbound window, are not allowed.
9.10.2
Address Translation
The address translation registers allow the remapping of inbound and outbound transactions. The reset
configuration for outbound transactions are that all outbound requests from the core side of the PCI bridge
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-24
Freescale Semiconductor
PCI Bridge
are routed to the PCI bus with address translation disabled. The reset configuration for inbound
transactions are that all inbound requests from the PCI bus are disabled.
9.10.2.1
PCI Inbound Translation
For inbound transactions (transactions generated by an external master on the PCI bus where the PCI
bridge responds as a slave device), the PCI bridge only responds to PCI addresses within the windows
mapped by the PCI inbound base address registers (PIBARs). If there is an address hit in one of the
PIBARs, the PCI address is translated from PCI space to local memory space through the associated PCI
inbound translation address registers (PITARs). This allows an external master to access local memory on
the 60x’s bus. Each PIBAR register is associated with a PITAR and PICMR (PCI inbound comparison
mask register) which are located in the PCI bridge’s PCI internal register space. Figure 9-15 shows an
example translation window for inbound memory accesses.
PCI memory view
60x bus view
0
0
Peripheral memory
window
System memory
Local memory
PCI inbound
translation
address
PCI inbound
window size
Inbound address
translation
PCI memory
PCI inbound
base
address
PCI memory
Local peripheral
memory
PCI inbound
window size
4G
4G
Figure 9-15. Inbound PCI Memory Address Translation
There are two sets of inbound translation registers, allowing two simultaneous translation windows.
Software can move the translation base addresses during run-time to access different portions of local
memory, but be sure that the PCI inbound translation windows do not overlap.
The reset configuration for the windows is disabled; that is, after reset, the PCI bridge does not
acknowledge externally mastered transactions on the PCI bus by asserting DEVSEL until the inbound
translation windows are enabled. The inbound translation is performed in the PCI interface.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-25
PCI Bridge
9.10.2.2
PCI Outbound Translation
Outbound address translation is provided to allow the outbound transactions to access any address over the
PCI memory or I/O space. Translation window’s base addresses are defined in the PCI outbound base
address registers (refer to Section 9.11.1.4, “PCI Outbound Base Address Registers (POBARx)”).
Transactions to these address ranges are issued on the PCI bus with a translated address. The translation
addresses are defined in the associated PCI outbound translation address registers (POTARs). Outbound
addresses that fall outside the outbound windows are forwarded to the PCI bus without modification.
Figure 9-16 shows an example translation window for outbound memory accesses.
PCI memory view
60x bus view
0
0
System memory
PCI outbound
translation
address
Local memory
System memory
window
Outbound
memory
window size
Outbound address
translation
PCI memory
PCI memory
Outbound memory
window
Transactions outside
the window forwarded
without modification
4G
PCI outbound
base
address
Outbound
memory
window size
4G
Figure 9-16. Outbound PCI Memory Address Translation
The three sets of outbound translation registers allow three simultaneous translation windows. Software
can move and adjust the host memory window translations and sizes during run-time. This allows software
to access host memory or to address alternate memory space on the fly, but be sure that the PCI outbound
translation windows do not overlap. Also note that the PCI outbound translation windows should not
overlap with the PCI bridge internal register space defined by the PIMMR.
9.10.3
SIU Registers
PCI utilizes fields in general SIU registers (SIUMCR, TESCR1, TESCR2, and L-TESCR1). There are also
two pairs of PCI-specific registers that detect accesses from the 60x bus side to the PCI bridge (other than
PCI internal registers accesses). Refer to Section 4.3.4, “PCI Control Registers.”
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-26
Freescale Semiconductor
PCI Bridge
9.11
Configuration Registers
There are two types of configuration registers in the PCI bridge: PCI-specified and memory-mapped. The
PCI-specified type, referred to as PCI configuration registers, are accessed through PCI configuration
cycles (refer to Section 9.11.2, “PCI Bridge Configuration Registers”). The memory-mapped
configuration registers are placed in the internal memory map of the MPC8280 and are accessed like other
internal registers (refer to Section 9.11.1, “Memory-Mapped Configuration Registers”).
Both the PCI configuration and memory-mapped internal registers of the PCI bridge are intrinsically
little-endian and are described using classic bit-numbering; that is, the lowest memory address contains
the least significant byte of the register and bit 0 is the least-significant bit of the register.
NOTE: Accessing Configuration Registers
For a PCI device to share little-endian (LE) data with the 603e core CPU,
software must byte-swap the data of the configuration register. Refer to
Section 9.11.2.27, “PCI Configuration Register Access in Big-Endian
Mode,” and Section 9.11.2.27.1, “Additional Information on Endianess.”
Also note that reserved bits in the configuration registers are not guaranteed to have predictable values.
Software must preserve the values of reserved bits when writing to a configuration register. Also, when
reading from a configuration register, software should not rely on the value of reserved bits remaining
constant.
NOTE: Accessing PCI Registers in Non-PCI Mode
In non-PCI mode, a 60x bus master should not attempt to access the PCI
memory mapped configuration registers. Doing so will cause the internal
memory space of the MPC8280 to be inaccessible. Any following access to
the internal memory space will not be terminated normally, and can only be
terminated by TEA if the 60x bus monitor is activated. The system can
recover only after a soft reset.
9.11.1
Memory-Mapped Configuration Registers
Table 9-3 describes the memory-mapped configuration registers provided by the PCI bridge. Note that
memory gaps not defined are reserved and should not be accessed.
Table 9-3. Internal Memory Map
Address
(offset)
Register
Access
Reset
Section/Page
0x10430
Outbound interrupt status register (OMISR)
special 0x0000_0000 9.12.3.4.3/9-80
0x10434
Outbound interrupt mask register (OMIMR)
R/W
0x0000_0000 9.12.3.4.4/9-81
0x10440
Inbound FIFO queue port register (IFQPR)
R/W
0x0000_0000 9.12.3.4.1/9-78
0x10444
Outbound FIFO queue port register (OFQPR)
R/W
0x0000_0000 9.12.3.4.2/9-79
0x10450
Inbound message register 0 (IMR0)
R/W
undefined
9.12.1.1/9-67
0x10454
Inbound message register 1 (IMR1)
R/W
undefined
9.12.1.1/9-67
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-27
PCI Bridge
Table 9-3. Internal Memory Map (continued)
Address
(offset)
Register
Access
Reset
Section/Page
0x10458
Outbound message register 0 (OMR0)
R/W
undefined
9.12.1.2/9-67
0x1045C
Outbound message register 1 (OMR1)
R/W
undefined
9.12.1.2/9-67
0x10460
Outbound doorbell register (ODR)
R/W
0x0000_0000
9.12.2.1/9-68
0x10468
Inbound doorbell register (IDR)
R/W
0x0000_0000
9.12.2.2/9-69
0x10480
Inbound message interrupt status register (IMISR)
R/W
0x0000_0000 9.12.3.4.5/9-82
0x10484
Inbound message interrupt mask register (IMIMR)
R/W
0x0000_0000 9.12.3.4.6/9-83
0x104A0
Inbound free_FIFO head pointer register (IFHPR)
R/W
0x0000_0000 9.12.3.2.1/9-72
0x104A8
Inbound free_FIFO tail pointer register (IFTPR)
R/W
0x0000_0000 9.12.3.2.1/9-72
0x104B0
Inbound post_FIFO head pointer register (IPHPR)
R/W
0x0000_0000 9.12.3.2.2/9-73
0x104B8
Inbound post_FIFO tail pointer register (IPTPR)
R/W
0x0000_0000 9.12.3.2.2/9-73
0x104C0
Outbound free_FIFO head pointer register (OFHPR)
R/W
0x0000_0000 9.12.3.3.1/9-75
0x104C8
Outbound free_FIFO tail pointer register (OFTPR)
R/W
0x0000_0000 9.12.3.3.1/9-75
0x104D0
Outbound post_FIFO head pointer register (OPHPR)
R/W
0x0000_0000 9.12.3.3.2/9-76
0x104D8
Outbound post_FIFO tail pointer register (OPTPR)
R/W
0x0000_0000 9.12.3.3.2/9-76
0x104E4
Message unit control register (MUCR)
R/W
0x0000_0002 9.12.3.4.7/9-84
0x104F0
Queue base address register (QBAR)
R/W
0x0000_0000 9.12.3.4.8/9-85
0x10500
DMA 0 mode register (DMAMR0)
R/W
0x0000_0000 9.13.1.6.1/9-89
0x10504
DMA 0 status register (DMASR0)
R/W
0x0000_0000 9.13.1.6.2/9-91
0x10508
DMA 0 current descriptor address register (DMACDAR0)
R/W
0x0000_0000 9.13.1.6.3/9-92
0x10510
DMA 0 source address register (DMASAR0)
R/W
0x0000_0000 9.13.1.6.4/9-93
0x10518
DMA 0 destination address register (DMADAR0)
R/W
0x0000_0000 9.13.1.6.5/9-94
0x10520
DMA 0 byte count register (DMABCR0)
R/W
0x0000_0000 9.13.1.6.6/9-94
0x10524
DMA 0 next descriptor address register (DMANDAR0)
R/W
0x0000_0000 9.13.1.6.7/9-95
0x10580
DMA 1 mode register (DMAMR1)
R/W
0x0000_0000 9.13.1.6.1/9-89
0x10584
DMA 1 status register (DMASR1)
R/W
0x0000_0000 9.13.1.6.2/9-91
0x10588
DMA 1 current descriptor address register (DMACDAR1)
R/W
0x0000_0000 9.13.1.6.3/9-92
0x10590
DMA 1 source address register (DMASAR1)
R/W
0x0000_0000 9.13.1.6.4/9-93
0x10598
DMA 1 destination address register (DMADAR1)
R/W
0x0000_0000 9.13.1.6.5/9-94
0x105A0
DMA 1 byte count register (DMABCR1)
R/W
0x0000_0000 9.13.1.6.6/9-94
0x105A4
DMA 1 next descriptor address register (DMANDAR1)
R/W
0x0000_0000 9.13.1.6.7/9-95
0x10600
DMA 2 mode register (DMAMR2)
R/W
0x0000_0000 9.13.1.6.1/9-89
0x10604
DMA 2 status register (DMASR2)
R/W
0x0000_0000 9.13.1.6.2/9-91
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-28
Freescale Semiconductor
PCI Bridge
Table 9-3. Internal Memory Map (continued)
Address
(offset)
Register
Access
Reset
Section/Page
0x10608
DMA 2 current descriptor address register (DMACDAR2)
R/W
0x0000_0000 9.13.1.6.3/9-92
0x10610
DMA 2 source address register (DMASAR2)
R/W
0x0000_0000 9.13.1.6.4/9-93
0x10618
DMA 2 destination address register (DAR2)
R/W
0x0000_0000 9.13.1.6.5/9-94
0x10620
DMA 2 byte count register (DMABCR2)
R/W
0x0000_0000 9.13.1.6.6/9-94
0x10624
DMA 2 next descriptor address register (DMANDAR2)
R/W
0x0000_0000 9.13.1.6.7/9-95
0x10680
DMA 3 mode register (DMAMR3)
R/W
0x0000_0000 9.13.1.6.1/9-89
0x10684
DMA 3 status register (DMASR3)
R/W
0x0000_0000 9.13.1.6.2/9-91
0x10688
DMA 3 current descriptor address register (DMACDAR3)
R/W
0x0000_0000 9.13.1.6.3/9-92
0x10690
DMA 3 source address register (DMASAR3)
R/W
0x0000_0000 9.13.1.6.4/9-93
0x10698
DMA 3 destination address register (DMADAR3)
R/W
0x0000_0000 9.13.1.6.5/9-94
0x106A0
DMA 3 byte count register (DMABCR3)
R/W
0x0000_0000 9.13.1.6.6/9-94
0x106A4
DMA 3 next descriptor address register (DMANDAR3)
R/W
0x0000_0000 9.13.1.6.7/9-95
0x10800
PCI outbound translation address register 0 (POTAR0)
R/W
0x0000_0000
9.11.1.3/9-30
0x10808
PCI outbound base address register 0 (POBAR0)
R/W
0x0000_0000
9.11.1.4/9-31
0x10810
PCI outbound comparison mask register 0 (POCMR0)
R/W
0x0000_0000
9.11.1.5/9-32
0x10818
PCI outbound translation address register 1 (POTAR1)
R/W
0x0000_0000
9.11.1.3/9-30
0x10820
PCI outbound base address register 1 (POBAR1)
R/W
0x0000_0000
9.11.1.4/9-31
0x10828
PCI outbound comparison mask register 1 (POCMR1)
R/W
0x0000_0000
9.11.1.5/9-32
0x10830
PCI outbound translation address register 2 (POTAR2)
R/W
0x0000_0000
9.11.1.3/9-30
0x10838
PCI outbound base address register 2 (POBAR2)
R/W
0x0000_0000
9.11.1.4/9-31
0x10840
PCI outbound comparison mask register 2 (POCMR2)
R/W
0x0000_0000
9.11.1.5/9-32
0x10878
Discard timer control register (PTCR)
R/W
0x0000_0000
9.11.1.6/9-33
0x1087C
General purpose control register (GPCR)
R/W
0x0000_0000
9.11.1.7/9-33
0x10880
PCI general control register (PCI_GCR)
R/W
0x0000_0000
9.11.1.8/9-35
0x10884
Error status register (ESR)
R/W
0x0000_0000
9.11.1.9/9-35
0x10888
Error mask register (EMR)
R/W
0x0000_0FFF 9.11.1.10/9-37
0x1088C
Error control register (ECR)
R/W
0x0000_00FF
9.11.1.11/9-38
0x10890
PCI error address capture register (PCI_EACR)
R/W
0x0000_0000
9.11.1.12/9-39
0x10898
PCI error data capture register (PCI_EDCR)
R/W
0x0000_0000
9.11.1.13/9-40
0x108A0
PCI error control capture register (PCI_ECCR)
R/W
0x0000_0000
9.11.1.14/9-40
0x108D0
PCI inbound translation address register 1 (PITAR1)
R/W
0x0000_0000
9.11.1.15/9-42
0x108D8
PCI inbound base address register 1 (PIBAR1)
R/W
0x0000_0000
9.11.1.16/9-42
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-29
PCI Bridge
Table 9-3. Internal Memory Map (continued)
Address
(offset)
Register
Access
Reset
Section/Page
0x108E0
PCI inbound comparison mask register 1 (PICMR1)
R/W
0x0000_0000
9.11.1.17/9-43
0x108E8
PCI inbound translation address register 0 (PITAR0)
R/W
0x0000_0000
9.11.1.15/9-42
0x108F0
PCI inbound base address register 0 (PIBAR0)
R/W
0x0000_0000
9.11.1.16/9-42
0x108F8
PCI inbound comparison mask register 0 (PICMR0)
R/W
0x0000_0000
9.11.1.17/9-43
0x10900
PCI CFG_ADDR
R/W
undefined
9.9.1.4.4/9-15
0x10904
PCI CFG_DATA
R/W
0x0000_0000
9.9.1.4.4/9-15
0x10908
PCI INT_ACK
R/W
undefined
9.9.1.4.7/9-17
9.11.1.1
Message Unit (I2O) Registers
Message unit registers are described in Section 9.12, “Message Unit (I2O),” on page 9-66.
9.11.1.2
DMA Controller Registers
DMA registers are described in Section 9.13, “DMA Controller,” on page 9-86.
9.11.1.3
PCI Outbound Translation Address Registers (POTARx)
The PCI outbound translation address registers (POTARx), shown in Figure 9-17, select the starting
addresses in PCI address space for locally generated transactions that hit within the outbound translation
windows. The new translated address is created by concatenating the transaction offset to this translation
address. Refer to Section 9.10.2.2, “PCI Outbound Translation.”
31
Field
20
19
16
—
Reset
TA
0000_0000_0000_0000
R/W
R/W
Addr
0x10802 (POTAR0); 0x1081A (POTAR1); 0x10832 (POTAR2)
15
0
Field
TA
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x10800 (POTAR0); 0x10818 (POTAR1); 0x10830 (POTAR2)
Figure 9-17. PCI Outbound Translation Address Registers (POTARx)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-30
Freescale Semiconductor
PCI Bridge
Table 9-4 describes POTARx.
Table 9-4. POTARx Field Descriptions
Bits
Name
31–20
—
19–0
Translation Address
9.11.1.4
Description
Reserved, should be cleared.
PCI address which indicates the starting point of the outbound translated
address. The translation address must be aligned based on the window’s size.
This corresponds to bits 31-12 of a 32-bit address
PCI Outbound Base Address Registers (POBARx)
The PCI outbound base address registers (POBARx), shown in Figure 9-18, select the base address for the
windows which are translated to the PCI address space for transactions generated by the 60x bus master
or other local devices such as the DMA controller.
31
20
Field
19
—
Reset
16
BA
0000_0000_0000_0000
R/W
R/W
Addr
0x1080A (POBAR0); 0x10822 (POBAR1); 0x1083A (POBAR2)
15
0
Field
BA
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x10808 (POBAR0); 0x10820 (POBAR1); 0x10838 (POBAR2)
Figure 9-18. PCI Outbound Base Address Registers (POBARx)
Table 9-5 describes POBARx.
Table 9-5. POBARx Field Descriptions
Bits
Name
Description
31–20
—
19–0
Base Address
Reserved, should be cleared.
Local address which is the starting point for the outbound translation window.
This corresponds to bits 31-12 of a 32-bit address
Addresses for outbound transactions are compared to the POBARs and the IMMR register. If the
transaction does not fall within one of these two spaces, it is forwarded to the PCI bus without modification
(see Figure 9-11). DMA-generated transactions to addresses which “miss” the POBARs are issued
(without translation) to the 60x bus (see Figure 9-13).
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-31
PCI Bridge
9.11.1.5
PCI Outbound Comparison Mask Registers (POCMRx)
The PCI outbound comparison mask registers (POCMRx), shown in Figure 9-19, defines the window size
to translate.
Field
31
30
29
28
EN
I/O
PRE
20
19
16
—
Reset
CM
0000_0000_0000_0000
R/W
R/W
Addr
0x10812 (POCMR0); 0x2082A (POCMR1); 0x10842 (POCMR2)
15
0
Field
CM
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x10810 (POCMR0); 0x20828 (POCMR1); 0x10840 (POCMR2)
Figure 9-19. PCI Outbound Comparison Mask Registers (POCMRx)
Table 9-6 describes POCMRx.
Table 9-6. POCMRx Field Descriptions
Bits
Name
Description
31
Enable
30
I/O
29
Prefetchable
28–20
—
19–0
Comparison mask
This bit enables this address translation
This bit indicates that the translation is to PCI memory or PCI I/O space
0 PCI memory
1 PCI I/O
This bit indicates that the address space is prefetchable, so streaming can occur
0 not prefetchable
1 prefetchable
Reserved, should be cleared.
Comparison mask indicates the size of the space to be translated. The value in the
register represents which of the most significant address bits to compare for a
window match. Non-contiguous comparison masks will exhibit unpredictable
behavior.
Examples:
POCMR = 0b0xxx_xxxx_xxxx_xxxx_xxxx_xxxx_xxxx_xxxx
Translation is disabled. All addresses received pass through unaltered.
POCMR = 0b1xxx_xxxx_xxxx_1111_1111_1111_1111_1111
20 bits (physical address bits 31-12) are comparison masked for a 4Kbyte window
size. This is the smallest window size allowed.
POCMR = 0b1xxx_xxxx_xxxx_1111_1111_1111_0000_0000
12 bits (physical address bits 31-20) for a 1Mbyte window size.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-32
Freescale Semiconductor
PCI Bridge
9.11.1.6
Discard Timer Control Register (PTCR)
The discard timer control register (PTCR), shown in Figure 9-20, configures the discard timer used to put
a time limit on delayed read transactions from non-prefetchable memory.
31
Field
30
24
EN
23
16
—
Reset
PTV
0000_0000_0000_0000
R/W
R/W
Addr
0x1087A
15
0
Field
PTV
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x10878
Figure 9-20. Discard Timer Control register (PTCR)
Table 9-7 describes PTCR fields.
Table 9-7. PTCR Field Descriptions
Bits
Name
31
Enable
30–24
—
23–0
Preload timer value
9.11.1.7
Description
Discard timer enable.
0 Disable the discard timer
1 Enable the discard timer
Reserved
Preload value for 24-bit discard timer. Delayed PCI read transactions to a
non-prefetchable address space remain valid within the PCI bridge a minimum of
(224 - Preload Timer Value) internal clock cycles. The discard timer is used to
discard delayed reads from non-prefetchable address space if the master has not
repeated the transaction in n internal clock cycles, where n = (224 - Preload Timer
Value). Valid Preload Timer Values are in the range 0x000000–0xFFFFFE.
Example: To discard a delayed completion if the PCI master has not repeated the
transaction in 215 PCI clocks and the internal frequency is 2 to 1 to the PCI bus. The
Preload Timer Value should equal 224 - 216 (0xFF0000).
General Purpose Control Register (GPCR)
The general purpose control register (GPCR), shown in Figure 9-21, contains control bits for rerouting
interrupts and adjusting the DMA controller’s 60x bandwidth.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-33
PCI Bridge
31
20
Field
—
Reset
18
17
DMABC
16
—
0000_0000_0000_0000
R/W
R/W
Addr
0x1087E
Field
19
15
14
13
—
INTPCI
MCP2PCI
Reset
12
1
—
0
LE_MODE
0000_0000_0000_0000
R/W
R/W
Addr
0x1087C
Figure 9-21. General Purpose Control Register (GPCR)
Table 9-8 describes GPCR fields.
Table 9-8. GPCR Field Descriptions
Bits
Name
Description
31–20
—
19–18
DMABC
17–15
—
14
INT2PCI
Interrupt reroute to PCI.
0 Interrupts are not rerouted to the PCI. Sent to the core if it is enabled or output
on IRQ7 if the core is disabled.
1 All SIU pending interrupts are rerouted to PCI's INTA. Useful in agent mode.
13
MCP2PCI
Machine check reroute to PCI.
0 Machine check interrupts are not rerouted to the PCI. Sent to the core if it is
enabled or output on IRQ0 if the core is disabled
1 All machine check interrupts are rerouted to PICE’s INTA. Useful in agent
mode.
Reserved, should be cleared.
DMA 60x bandwidth control
00 DMA uses low 60x bandwidth.
01 DMA uses high 60x bandwidth.
10 DMA uses maximum 60x bus bandwidth.
11 DMA uses minimum 60x bandwidth.
Allows breaks to be inserted in the DMA controller operation. This control may
be needed to avoid starvation of other 60x masters because the PCI bridge can
have higher priorities than other masters. The breaks are inserted only if some
other 60x bus master requests the bus.
The user should find the optimum setting by testing, arriving at the best for each
specific implementation. For most systems the default value (low 60x bandwidth
for the dma) will be good. Note that if the dma is the only master that needs the
bus during the period of the
transfer, the bandwidth is not affected.
Reserved, should be cleared.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-34
Freescale Semiconductor
PCI Bridge
Table 9-8. GPCR Field Descriptions (continued)
Bits
Name
12–1
—
0
LE_MODE
9.11.1.8
Description
Reserved, should be cleared.
Little endian mode. Controls the translation of 60x-PCI and PCI-60x. Refer to
Section 9.11.2.27.1, “Additional Information on Endianess,” for more details.
0 Big endian mode.
1 Little endian mode.
PCI General Control Register (PCI_GCR)
The PCI general control register (PCI_GCR), shown in Figure 9-22, contains a bit for controlling the PCI
reset signal when in host mode.
31
16
Field
—
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x10882
15
1
Field
—
Reset
0
SPRST
0000_0000_0000_0000
R/W
R/W
Addr
0x10880
Figure 9-22. PCI General Control Register (PCI_GCR)
Table 9-9 describes PCI_GCR fields.
Table 9-9. PCI_GCR Field Descriptions
Bits
Name
31–1
—
0
Soft PCI Reset
9.11.1.9
Description
Reserved, should be cleared.
Only valid when in host mode. Allows PCI_RST to be controlled software.
Setting this bit drives the PCI reset signal high; clearing it drives the signal low.
Error Status Register (ESR)
The error status register (ESR), shown in Figure 9-23, contains status bits for various types of error
conditions captured by the PCI bridge. Each status bit is set when the corresponding error condition is
captured. Each bit is cleared by writing a one.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-35
PCI Bridge
31
16
Field
—
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x10886
15
Field
13
—
12
11
10
I2O_
DBMC
NMI
IRA
Reset
9
8
7
6
5
4
I2O_ I2O_ PERR_ PERR_ PCI_ TAR_
IPQO OFQO WR
RD SERR ABT
3
NO_
RSP
2
1
0
DATA_ DATA_
ADDR_
PAR_ PAR_
PAR
WR
RD
0000_0000_0000_0000
R/W
R/W
Addr
0x10884
Figure 9-23. Error Status Register (ESR)
Table 9-10 describes ESR fields.
Table 9-10. ESR Field Descriptions
Bits
Name
Description
31–13
—
12
I2O_DBMC
Reserved, should be cleared.
I2O DoorBell Machine Check. When a PCI-mastered write sets IDBR[31], a
machine check is sent to the local processor and the event is reported in
ESR[I2O_DBMC].
This bit is also set in the following cases:
• An overflow condition in the inbound posted I2O queue
• An overflow condition in the outbound free I2O queue.
These two interrupts can be masked in the I2O unit.
11
NMI
General error/interrupt indication. In host mode, this bit is set when a 60x bus
write transaction initiated by the PCI bridge is terminated by the assertion of
TEA. In agent mode, this bit is set when the GPCR[MCP2PCI] bit is set and an
internal machine check interrupt (MCP) is issued by one of the MPC8280’s MCP
sources.
Machine check and interrupt assertion is determined by ECR[11].
The reset value of ECR[11], logic zero, indicates that an interrupt will be asserted
if ESR[NMI] is set (and enabled per EMR[11]).
10
IRA
Illegal register access with incorrect size.
9
I2O_IPQO
I2O inbound post queue overflow.
8
I2O_OFQO
I2O outbound free queue overflow.
7
PCI_PERR_WR
PCI parity error received on a write.
6
PCI_PERR_RD
PCI parity error received on a read.
5
PCI_SERR
4
PCI_TAR_ABT
PCI SERR received.
PCI target abort
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-36
Freescale Semiconductor
PCI Bridge
Table 9-10. ESR Field Descriptions (continued)
Bits
Name
Description
3
PCI_NO_RSP
2
PCI_DATA_PAR_RD
PCI read data parity error.
1
PCI_DATA_PAR_WR
PCI write data parity error.
0
PCI_ADDR_PAR
PCI no response (no DEVSEL; master abort).
PCI address parity error (read or write).
9.11.1.10 Error Mask Register (EMR)
The error mask register (EMR) register, shown in Figure 9-24, enables the IOU to assert an interrupt or a
machine check for the various types of error conditions listed in Table 9-10. Each mask bit is active high.
That is, if a bit value is zero, an interrupt or machine check is not asserted for the corresponding error
condition.
31
16
Field
—
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x1088A
15
Field
13
12
11
I2O_
DBMC
—
NMI
Reset
10
IRA
9
I2O_
IPQO
8
7
I2O_
OFQO
PERR
_WR
6
PERR
_RD
5
PCI_
SERR
4
TAR_
ABT
3
NO_
RSP
2
1
0
DATA_ DATA_
ADDR
PAR_ PAR_
_PAR
RD
WR
0000_1111_1111_1111
R/W
R/W
Addr
0x10888
Figure 9-24. Error Mask Register (EMR)
Table 9-11 describes EMR fields.
Table 9-11. EMR Field Descriptions
Bits
Name
Description
31–13
—
12
I2O_DBMC
I2O doorbell machine check.
0 Machine check is not enabled
1 Machine check is enabled
11
NMI
General error/interrupt indication.
10
IRA
Illegal register access with incorrect size.
9
I2O_IPQO
I2O inbound post queue overflow.
8
I2O_OFQO
I2O outbound free queue overflow.
Reserved, should be cleared.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-37
PCI Bridge
Table 9-11. EMR Field Descriptions (continued)
Bits
Name
Description
7
PCI_PERR_WR
PCI parity error received on a write. The MPC8280 sinks PERR. This error is only
a function of data.
6
PCI_PERR_RD
PCI parity error received on a read. The MPC8280 sinks PERR. This error is only
a function of data.
5
PCI_SERR
4
PCI_TAR_ABT
PCI target abort
3
PCI_NO_RSP
PCI no response (no DEVSEL; master abort).
2
PCI_DATA_PAR_RD
PCI read data parity error. The MPC8280 sources PERR. This error is only a
function of data.
1
PCI_DATA_PAR_WR
PCI write data parity error. The MPC8280 sources PERR. This error is only a
function of data.
0
PCI_ADDR_PAR
PCI SERR received.
PCI address parity error (read or write).
9.11.1.11 Error Control Register (ECR)
The error control register (ECR) register, shown in Figure 9-25, determines whether the IOU asserts an
interrupt or a machine check for the error conditions listed in Table 9-10. The IOU asserts an interrupt or
machine check only if the mask bit for the error condition (refer to Table 9-11) is set. Each bit is defined
as follows:
• Zero: The IOU issues an interrupt upon the error condition.
• One: The IOU issues a machine check upon the error condition.
31
16
Field
—
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x1088E
15
Field
Reset
13
—
12
11
10
I2O_
DBMC
NMI
IRA
9
8
7
6
5
4
I2O_ I2O_ PERR_ PERR_
TAR_
SERR
IPQO OFQO WR
RD
ABT
3
NO_
RSP
2
1
0
DATA_ DATA_
ADDR_
PAR_ PAR_
PAR
WR
RD
0000_0000_1111_1111
R/W
R/W
Addr
0x1088C
Figure 9-25. Error Control Register (ECR)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-38
Freescale Semiconductor
PCI Bridge
Table 9-12 describes ECR fields.
Table 9-12. ECR Field Descriptions
Bits
Name
Description
31–13
—
12
I2O_DBMC
11
NMI
General error/interrupt indication
10
IRA
Illegal register access with incorrect size
9
I2O_IPQO
I2O inbound post queue overflow
8
I2O_OFQO
I2O outbound free queue overflow
7
PCI_PERR_WR
PCI parity error received on a write
6
PCI_PERR_RD
PCI parity error received on a read
5
PCI_SERR
4
PCI_TAR_ABT
PCI target abort
3
PCI_NO_RSP
PCI no response (no DEVSEL; master abort)
2
PCI_DATA_PAR_RD
PCI read data parity error
1
PCI_DATA_PAR_WR
PCI write data parity error
0
PCI_ADDR_PAR
Reserved, should be cleared
I2O doorbell machine check
0 ESR[I2O_DBMC] causes an interrupt.
1 ESR[I2O_DBMC] (if enabled) causes a machine check.
PCI SERR received
PCI address parity error (read or write)
9.11.1.12 PCI Error Address Capture Register (PCI_EACR)
The PCI error address capture register (PCI_EACR), shown in Figure 9-26, stores the address associated
with the first PCI error captured.
31
16
Field
PCI_EAR
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x10892
15
0
Field
PCI_EAR
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x10890
Figure 9-26. PCI Error Address Capture Register (PCI_EACR)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-39
PCI Bridge
Table 9-13 describes PCI_EACR fields.
Table 9-13. PCI_EACR Field Descriptions
Bits
Name
Description
31–0
PCI_EAR
The address associated with the first error captured.
9.11.1.13 PCI Error Data Capture Register (PCI_EDCR)
The PCI error data capture register (PCI_EDCR), shown in Figure 9-27, stores the data associated with the
first PCI error captured.
31
16
Field
PCI_EDR
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x1089A
15
0
Field
PCI_EDR
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x10898
Figure 9-27. PCI Error Data Capture Register (PCI_EDCR)
Table 9-14 describes PCI_EDCR fields.
Table 9-14. PCI_EDCR Field Description
Bits
Name
Description
31–0
PCI_EDR
The data associated with the first error captured.
9.11.1.14 PCI Error Control Capture Register (PCI_ECCR)
The PCI error control capture register (PCI_ECCR), shown in Figure 9-28, stores information associated
with the first PCI error captured.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-40
Freescale Semiconductor
PCI Bridge
31
Field
30
—
28
27
FET
24
23
BN
Reset
21
—
20
19
16
TS
ES
0000_0000_0000_0000
R/W
R/W
Addr
0x108A2
15
Field
22
12
11
CMD
8
7
4
—
Reset
3
BE
2
—
1
0
PB
VI
0000_0000_0000_0000
R/W
R/W
Addr
0x108A0
Figure 9-28. PCI Error Control Capture Register (PCI_ECCR)
Table 9-15 describes PCI_ECCR fields.
Table 9-15. PCI_ECCR Field Descriptions
Bits
Name
Description
31
—
30–28
First error type
Reserved, should be cleared.
Type of first PCI error captured. This field is the bit index of the error type in
Table 9-10. For example, a value of 0b101 indicates a PCI SERR received
condition while a value of 0b010 indicates a PCI read data parity error.
27–24
Beat number
23–22
—
21–20
Transaction size
19–16
Error source
15–12
Command
11–8
—
7–4
Byte enables
3–2
—
32-bit data beat number for data parity error (data parity error only)
0000 1
0001 2
…
0111 8
1000 overflow (transaction larger than one cache line)
Reserved, should be cleared.
This is the size of the transaction in doublewords (4 bytes) (the PCI bridge as
master only)
00 4 double words
01 1 double word
10 2 double words
11 3 double words
The source of the PCI transaction
0000 External master
0001 60x master
0101 DMA
All others are reserved.
PCI command
Reserved, should be cleared.
PCI byte enables.
Reserved, should be cleared.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-41
PCI Bridge
Table 9-15. PCI_ECCR Field Descriptions (continued)
Bits
Name
Description
1
Parity bit
Parity bit for PCI bus data word.
0
Valid info
When this bit is set, the PCI bus error capture registers (PCI_EACR, PCI_EDCR,
and PCI_ECCR) contain valid information.
Writing ‘0’ to this bit enables the capture of a new error in the PCI bus error
capture registers (PCI_EACR, PCI_EDCR, and PCI_ECCR).
9.11.1.15 PCI Inbound Translation Address Registers (PITARx)
The PCI inbound translation address registers (PITARx), shown in Figure 9-29, select the base addresses
in the 60x address space of the translation windows for transactions generated by the master on the PCI
bus. The new translated address is created by concatenating the transaction offset to this base address.
Refer to Section 9.10.2.1, “PCI Inbound Translation.”
31
20
Field
19
16
—
Reset
TA
0000_0000_0000_0000
R/W
R/W
Addr
0x108EC (PITAR0); 0x108D2 (PITAR1)
15
0
Field
TA
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x108EA (PITAR0); 0x108D0 (PITAR1)
Figure 9-29. PCI Inbound Translation Address Registers (PITARx)
Table 9-16 describes PITARx.
Table 9-16. PITARx Field Descriptions
Bits
Name
Description
31–20
—
19–0
Translation address
Reserved, should be cleared.
60x address which indicates the starting point of the inbound translated address.
The translation address must be aligned based on the window’s size. This
corresponds to bits 31-12 of a 32-bit address
9.11.1.16 PCI Inbound Base Address Registers (PIBARx)
The PCI inbound base address registers (PIBARx), shown in Figure 9-30, select the starting addresses (in
PCI memory space) of the windows to be translated. These registers are tied to the GPLABARx registers;
see Section 9.11.2.14, “General Purpose Local Access Base Address Registers (GPLABARx).” A change
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-42
Freescale Semiconductor
PCI Bridge
in a PIBARx register causes a change in the GPLABARx in the base address bits that are non-masked by
PICMRx, and vice versa.
The system host is responsible for the configuration of the base address by writing to GPLABARx;
therefore, in PCI agent mode, the PIBARx registers should be read-only. However, if the PCI bridge is
defined as the PCI host, it may be easier to configure its own inbound base address by writing directly to
the PIBARx registers.
31
20
Field
19
—
Reset
16
BA
0000_0000_0000_0000
R/W
R/W
Addr
0x108F2 (PITAR0); 0x108DA (PITAR0)
15
0
Field
BA
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x108F0 (PITAR0); 0x108D8 (PITAR0)
Figure 9-30. PCI Inbound Base Address Registers (PIBARx)
Table 9-17 describes PIBARx.
Table 9-17. PIBARx Field Descriptions
Bits
Name
Description
31–20
—
Reserved, should be cleared.
19–0
BA
Base address. PCI address which is the starting point for the inbound translation
window.This corresponds to bits 31–12 of a 32-bit address.
9.11.1.17 PCI Inbound Comparison Mask Registers (PICMRx)
The PCI inbound comparison mask registers (PICMRx), shown in Figure 9-31, defines the inbound
window’s size. In PCI agent mode, this register should be initialized (either by the core or by the CP’s
automatic EPROM load) before the AGENT_CFG_LOCK bit (see Section 9.11.2.22, “PCI Bus Function
Register”) can be cleared to enable the host to configure the device. Some of the fields of this registers are
tied to the GPLABARx registers; see Section 9.11.2.14, “General Purpose Local Access Base Address
Registers (GPLABARx).”
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-43
PCI Bridge
Field
31
30
29
EN
NO_
SNOOP_
EN
PRE
Reset
28
20
19
16
—
CM
0000_0000_0000_0000
R/W
R/W
Addr
0x108FA (PICMR0); 0x108E2 (PICMR1)
15
0
Field
CM
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x108F8 (PICMR0); 0x108E0 (PICMR1)
Figure 9-31. PCI Inbound Comparison Mask Registers (PICMRx)
Table 9-18 describes PICMRx.
Table 9-18. PICMRx Field Descriptions
Bits
Name
Description
31
Enable
30
NO_SNOOP_EN
Controls whether the PCI bridge generates snoop transactions on the 60x bus for
PCI-to-60x memory transactions which hit in this address translation window.
Disabling snooping is a performance enhancement for systems that do not need to
maintain coherency on system memory accesses by PCI.
0 Snooping is enabled.
1 Snooping is disabled.
29
Prefetchable
Indicates whether the address space is prefetchable so that streaming can occur.
0 not prefetchable
1 prefetchable
28–20
—
19–0
Comparison mask
Setting this bit enables address translation
Reserved, should be cleared.
Indicates the size of the space to be translated. The value in the register represents
which of the most significant address bits to compare for a window match.
Non-contiguous comparison mask bits cause unpredictable behavior.
Examples:
PICMR = 0b0xxx_xxxx_xxxx_xxxx_xxxx_xxxx_xxxx_xxxx
Inbound window is disabled.
PICMR = 0b1xxx_xxxx_xxxx_1111_1111_1111_1111_1111
The mask is 20 bits (physical address bits 31-12) which corresponds to a 4Kbyte
window size. This is the smallest window size allowed.
PICMR = 0b1xxx_xxxx_xxxx_1111_1111_1111_0000_0000
The mask is 12 bits (physical address bits 31-20) which corresponds to a 1Mbyte
window size.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-44
Freescale Semiconductor
PCI Bridge
9.11.2
PCI Bridge Configuration Registers
The PCI Local Bus Specification defines the configuration registers from 0x00 through 0x3F. Additionally,
the PCI bridge specifies these additional registers: the PCI function register (at offset 0x44), the PCI arbiter
control register (at offset 0x46), and the PCI Hot Swap register block (at offset 0x48). Table 9-19 and
Figure 9-32 shows the PCI configuration registers provided by the PCI bridge for the PCI bus.
Note the following sections that apply to all PCI configuration registers (they appear immediately after the
descriptions of individual registers):
• Section 9.11.2.26, “PCI Configuration Register Access from the Core,” on page 9-62
• Section 9.11.2.27, “PCI Configuration Register Access in Big-Endian Mode,” on page 9-62
• Section 9.11.2.28, “Initializing the PCI Configuration Registers,” on page 9-64
Table 9-19. PCI Bridge PCI Configuration Registers
Address
(offset)
Register
Access
Reset
Section/Page
00
Vendor ID
R
0x1057
9.11.2.1/9-47
02
Device ID
R
0x18C0
9.11.2.2/9-47
04
PCI command
R/W
Mode-dependent
9.11.2.3/9-47
06
PCI status
Read/bit-reset
0x00B0
9.11.2.4/9-48
08
Revision ID
R
Rev-dependent
9.11.2.5/9-50
09
Standard programming interface
R
Mode-dependent
9.11.2.6/9-50
0A
Subclass code
R
0x00
9.11.2.7/9-51
0B
Class code
R
Mode-dependent
9.11.2.8/9-51
0C
Cache line size
R/W
0x00
9.11.2.9/9-52
0D
Latency timer
R/W
0x00
9.11.2.10/9-52
0E
Header type
R
0x00
9.11.2.11/9-53
0F
BIST control
R
0x00
9.11.2.12/9-53
10
PIMMR base address register
R/W
0xnnnn_0000
9.11.2.13/9-53
14
GPL base address register 0
R/W
0x0000_0000
9.11.2.14/9-54
18
GPL base address register 1
R/W
0x0000_0000
9.11.2.14/9-54
1C
Reserved
—
—
—
2C
Sub system vendor ID
R/W
0x0000
9.11.2.15/9-55
2E
Sub system device ID
R/W
0x0000
9.11.2.16/9-56
30
Reserved
—
—
—
34
Capabilities pointer
R
0x48
9.11.2.17/9-56
35
Reserved
—
—
—
3C
Interrupt line
R/W
0x00
9.11.2.18/9-57
3D
Interrupt pin
R
0x01
9.11.2.19/9-57
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-45
PCI Bridge
Table 9-19. PCI Bridge PCI Configuration Registers (continued)
Address
(offset)
Register
Access
Reset
Section/Page
3E
MIN GNT
R
0x00
9.11.2.20/9-58
3F
MAX LAT
R
0x00
9.11.2.21/9-58
40
Reserved
—
—
—
44
PCI function
R/W
0x0000
9.11.2.22/9-59
46
PCI arbiter control register
R/W
Mode-dependent
9.11.2.23/9-60
48
Hot swap register block
R/W
0x00nn_0006
9.11.2.24/9-61
9.11.2.25/9-61
Address offset
(Hex)
00
Device ID (0x18C0)
04
Vendor ID (0x1057)
PCI status
PCI command
08
Class code
Subclass code
Standard programming
Revision ID
0C
BIST control
Header type
Latency timer
Cache line size
10
PIMMR base address register
14
GPLA base address register 0
18
GPLA base address register 1
••
2C
Subsystem ID
Subsystem vendor ID
••
—
38
48
Capabilities pointer
—
MAX LAT
MIN GNT
40
44
••
—
34
3C
•
•
—
Interrupt pin
Interrupt line
—
PCI arbiter control
PCI function
Hot swap CSR
Hot swap capability ID
Figure 9-32. PCI Bridge PCI Configuration Registers
The PCI configuration registers are accessible from the core through an indirect method discussed in
“Section 9.11.2.26, PCI Configuration Register Access from the Core” on page 62. The registers are
accessible from the PCI bus through the PCI configuration transaction when the PCI bridge is in agent
mode.
The following sections describe the individual PCI configuration registers.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-46
Freescale Semiconductor
PCI Bridge
9.11.2.1
Vendor ID Register
Figure 9-33 and Table 9-20 describe the vendor ID register.
15
0
Field
VID
Reset
0001_0000_0101_0111
R/W
R
Addr
0x00
Figure 9-33. Vendor ID Register
Table 9-20. Vendor ID Register Description
Bits
Name
15–0
Vendor ID
9.11.2.2
Description
Identifies the manufacturer of the device (0x1057 = Freescale)
Device ID Register
Figure 9-34 and Table 9-21 describes the device ID register.
15
0
Field
DID
Reset
0001_1000_1100_0000
R/W
R
Addr
0x02
Figure 9-34. Device ID Register
Table 9-21. Device ID Register Description
Bits
Name
15–0
Device ID
9.11.2.3
Description
Identifies the particular device (0x18C0 = MPC8280)
PCI Bus Command Register
Figure 9-35 and Table 9-22 describe the PCI bus command register that provides control over the ability
to generate and respond to PCI cycles.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-47
PCI Bridge
15
10
—
Field
Reset
9
8
7
6
5
4
3
2
1
0
FB-B
SERR
—
PERRR
—
MWI
SC
BM
MEM
I/O
0000_0000_0000_0000
R/W
R/W
Addr
0x04
Figure 9-35. PCI Bus Command Register
Table 9-22. PCI Bus Command Register Description
Bits
Name
15–10
—
9
Fast back-to-back
8
SERR
7
—
6
Parity error response
5
—
4
Memory-write-andinvalidate
Hardwired to 0, indicating that the PCI bridge acting as a master does not generate
the memory-write-and-invalidate command. The PCI bridge generates a
memory-write command instead.
3
Special-cycles
Hardwired to 0, indicating that the PCI bridge as a target ignores all special-cycle
commands.
2
Bus master
1
Memory space
0
I/O space
9.11.2.4
Description
Reserved, should be cleared.
Hardwired to 0, indicating that the PCI bridge as a master does not run fast
back-to-back transactions.
Controls the SERR driver of the PCI bridge. This bit (and bit 6) must be set to report
address parity errors.
0 Disables the SERR driver
1 Enables the SERR driver
Reserved, should be cleared.
Controls whether the PCI bridge responds to parity errors on the PCI bus.
0 Parity errors are ignored and normal operation continues.
1 Action is taken on a parity error.
Reserved, should be cleared.
Controls whether the PCI bridge can act as a master on the PCI bus. This bit is
cleared if the PCI bridge is powered-up as an agent device and is set if it is
powered-up as a host bridge device.
0 Disables the ability to generate PCI accesses. In host bridge mode, read
transactions return undefined data and write transactions lose data. In agent
mode, transactions are held until this bit is enabled.
1 Enables the PCI bridge to behave as a PCI bus master
Controls whether the PCI bridge as a target responds to memory accesses.
0 The PCI bridge does not respond to PCI memory space accesses.
1 The PCI bridge responds to PCI memory space accesses.
Hardwired to 0, indicating that the PCI bridge as a target does not respond to PCI
I/O space accesses.
PCI Bus Status Register
The PCI bus status register, shown in Figure 9-36, is used to record status information for PCI bus-related
events. Only 2-byte accesses to address offset 0x06 are allowed.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-48
Freescale Semiconductor
PCI Bridge
Reads to this register behave normally. Writes are slightly different in that bits can be cleared, but not set.
A bit is cleared whenever the register is written, and the data in the corresponding bit location is set. For
example, to clear bit 14 and not affect any other bits in the register, write the value
0b0100_0000_0000_0000 to the register.
Field
15
14
13
12
11
DPERR
SSERR
RM-A
RT-A
ST-A
Reset
10
9
DEVSEL_T
8
7
6
5
4
DPD
FB-BC
—
66MHzC
CL
3
0
—
0000_0000_1011_0000
R/W
R/W
Addr
R
R/W
0x06
Figure 9-36. PCI Bus Status Register
Table 9-23 describes the PCI bus status register fields.
Table 9-23. PCI Bus Status Register Description
Bits
Name
Description
15
Detected parity error
Set whenever the PCI bridge detects a parity error on the PCI bus, even if parity
error handling is disabled (as controlled by bit 6 in the PCI bus command register).
14
Signaled system error
13
Received master-abort Set whenever the PCI bridge, acting as the PCI master on the PCI bus, terminates
a transaction (except for a special-cycle) using master-abort.
12
Received target-abort
Set whenever a PCI bridge-initiated transaction on the PCI bus is terminated by
a target-abort.
11
Signaled target-abort
Set whenever the PCI bridge, acting as the PCI target on the PCI bus, issues a
target-abort to a PCI master.
10–9
DEVSEL timing
Hardwired to 0b00, indicating that the PCI bridge uses fast device-select timing
on the PCI bus.
8
Data parity detected
Set upon detecting a data parity error on the PCI bus. Three conditions must be
met for this bit to be set:
• The PCI bridge detects a parity error.
• The PCI bridge is acting as the bus master for the operation in which the error
occurred.
• Bit 6 in the PCI bus command register is set.
7
Fast back-to-back
capable
Hardwired to 1, indicating that the PCI bridge as a target is capable of accepting
fast back-to-back transactions.
6
—
5
66-MHz capable
This bit is read-only and indicates that the PCI bridge is capable of 66-MHz PCI
bus operation on the PCI bus.
4
Capabilities List
Hardwired to 1, indicating that the PCI bridge implements new capabilities on the
PCI bus.
3–0
—
Set whenever the PCI bridge asserts SERR on the PCI bus.
Reserved, should be cleared.
Reserved, should be cleared.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-49
PCI Bridge
9.11.2.5
Revision ID Register
Figure 9-37 and Table 9-24 describe the revision ID register.
7
0
Field
RID
Reset
Refer to Table 9-24.
R/W
R
Addr
0x08
Figure 9-37. Revision ID Register
Table 9-24. Revision ID Register Description
Reset
Value
Bits
Name
7–0
Revision ID
9.11.2.6
Description
Revision Specifies a device-specific revision code for the MPC8280 (assigned
Dependent by Freescale). Revision ID = 0x11 for .25µm revisions A.0, B.1, and
C.0. Revision ID = 0x20 for 0.13µm devices.
PCI Bus Programming Interface Register
Figure 9-38 and Table 9-25 describe the PCI bus programming interface register.
7
0
Field
PI
Reset
Refer to Table 9-25.
R/W
R
Addr
0x09
Figure 9-38. PCI Bus Programming Interface Register
Table 9-25. PCI Bus Programming Interface Register Description
Bits
Name
Description
7–0
Programming interface
0x00 When the PCI bridge is configured as host bridge.
0x01 When the PCI bridge is configured as a peripheral device to indicate the
programming model supports the I2O interface.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-50
Freescale Semiconductor
PCI Bridge
9.11.2.7
Subclass Code Register
Figure 9-39 and Table 9-26 describe the subclass code register.
7
0
Field
SC
Reset
0000_0000
R/W
R
Addr
0x0A
Figure 9-39. Subclass Code Register
Table 9-26. Subclass Code Register Description
Bits
Name
7–0
Subclass code
9.11.2.8
Description
Identifies more specifically the function of the PCI bridge (0x00 = host bridge and
0x80 = agent mode)
PCI Bus Base Class Code Register
Figure 9-40 and Table 9-27 describe the PCI bus class code register.
7
0
Field
BCC
Reset
Refer to Table 9-27.
R/W
R
Addr
0x0B
Figure 9-40. PCI Bus Base Class Code Register
Table 9-27. PCI Bus Base Class Code Register Description
Bits
Name
Description
7–0
Base class code
0x06 When the PCI bridge is configured as a host bridge to indicate “Host Bridge”.
0x0E When the PCI bridge is configured as a target device to indicate the device
is an agent and is I2O capable.
NOTE: I2O Compliancy
When configured as a PCI agent device, the value of the Interface, Subclass
Code, and Base Class Code Registers are 0x01, 0x00, and 0x0E
respectively, indicating that the MPC8280 supports the I2O protocol. The
user should note that the I2O support is not fully standard compliant.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-51
PCI Bridge
9.11.2.9
PCI Bus Cache Line Size Register
Figure 9-41 and Table 9-28 describe the PCI bus cache line size register.
7
0
Field
CLS
Reset
0000_0000
R/W
R/W
Addr
0x0C
Figure 9-41. PCI Bus Cache Line Size Register
Table 9-28. PCI Bus Cache Line Size Register Description
Bits
Name
Description
7–0
Cache line size
Represents the cache line size of the system in terms of 32-bit words (eight 32-bit
words = 32 bytes). This register is read-write; however, an attempt to program this
register to any value other than 8 results in it being cleared.
9.11.2.10 PCI Bus Latency Timer Register
Figure 9-42 and Table 9-29 describe the PCI bus latency timer register.
7
3
Field
2
LT
Reset
0
LT
0000_0000
R/W
R/W
Addr
R
0x0D
Figure 9-42. PCI Bus Latency Timer Register
Table 9-29. PCI Bus Latency Timer Register Description
Bits
Name
Description
7–3
Latency timer
Represents the maximum number of PCI clocks that the device, when mastering
a transaction, holds the bus after PCI bus grant has been negated. The value is
in PCI clocks. Refer to the PCI 2.2 specification for the rules by which the PCI bus
interface unit completes transactions when the timer has expired.
2–0
Read-only least-significant bits of the latency timer. (The latency timer value is
programmed in multiples of eight.)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-52
Freescale Semiconductor
PCI Bridge
9.11.2.11 Header Type Register
Figure 9-43 and Table 9-30 describe the header type register.
7
Field
6
0
MD
HT
Reset
0000_0000
R/W
R
Addr
0x0E
Figure 9-43. Header Type Register
Table 9-30. Header Type Register Description
Bits
Name
Description
7
Multifunction device
6–0
Header type
The PCI bridge is not a multifunction PCI device.
Identifies the layout of bytes 0x10–0x3F of the configuration address space.
9.11.2.12 BIST Control Register
Figure 9-44 and Table 9-31 describe the BIST control register.
7
0
Field
BIST_CTRL
Reset
0000_0000
R/W
R
Addr
0x0F
Figure 9-44. BIST Control Register
Table 9-31. BIST Control Register Description
Bits
Name
Description
7–0
BIST control
Optional register for control and status of built-in self test (BIST)
9.11.2.13 PCI Bus Internal Memory-Mapped Registers Base Address Register
(PIMMRBAR)
In agent mode, the PCI bridge provides one base address register called the PCI bus internal
memory-mapped registers base address register (PIMMRBAR) to allow a host processor access to the
MPC8280’s internal memory-mapped registers. Transactions from PCI that “hit” the PIMMRBAR are
translated to the IMMR and sent to the logic that controls the internal memory-mapped registers.
PIMMRBAR is shown in Figure 9-45.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-53
PCI Bridge
31
17
Field
BA
Reset
16
BA
0000_0000_0000_0000
R/W
R/W
Addr
0x12
15
4
Field
BA
Reset
3
2
PRE
1
T
0
MSI
0000_0000_0000_0000
R/W
R/W
Addr
0x10
Figure 9-45. PCI Bus Internal Memory-Mapped Registers Base Address Register
(PIMMRBAR)
Table 9-32 describes PIMMRBAR fields.
Table 9-32. PIMMRBAR Field Descriptions
Bits
Name
31–17
Base address
Indicates the base address for the inbound configuration window.
16–4
Base address
Hardwired to zeros, indicating that the PCI bridge requires a 128-KByte space for
the configuration registers.
3
Prefetchable
Hardwired to 0 to indicate that this address region is not prefetchable.
2–1
Type
0
Description
Hardwired to 00 to indicate that the address can be located anywhere in 32-bit
address space.
Memory space indicator Address is mapped to memory space.
9.11.2.14 General Purpose Local Access Base Address Registers (GPLABARx)
Two general purpose local access base address registers (GPLABARx) are provided to allow access to
local memory space. These registers are closely tied to PIBARx and PICMRx (see Section 9.11.1.16, “PCI
Inbound Base Address Registers (PIBARx),” and Section 9.11.1.17, “PCI Inbound Comparison Mask
Registers (PICMRx)”). A write to GPLABARx causes a write to PIBARx but only to the bits allowed by
the PICMRx mask. Similarly, a write to PIBARx causes a write to GPLABARx of the non-masked bits of
the base address. GPLABARx is shown in Figure 9-46.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-54
Freescale Semiconductor
PCI Bridge
31
16
Field
BA
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x16 (GPLABAR0); 0x1A (GPLABAR1)
15
12
Field
11
4
BA
BA
Reset
3
PRE
2
1
T
0
MSI
0000_0000_0000_0000
R/W
R/W
Addr
0x14 (GPLABAR0); 0x18 (GPLABAR1)
Figure 9-46. General Purpose Local Access Base Address Registers (GPLABAR x)
Table 9-33 describes GPLABARx fields.
Table 9-33. GPLABARx Field Descriptions
Bits
Name
Description
31–12
Base address
Represents the base address for the inbound GPLA memory window. The number
of upper bits that the PCI bridge allows to be writable is selected through the PICMR;
see Section 9.11.1.17, “PCI Inbound Comparison Mask Registers (PICMRx).”
11–4
Hardwired to zeros. (The minimum window size allowed is 4K.)
3
Prefetchable
Corresponds to the prefetchable bit in the PICMR; see Section 9.11.1.17, “PCI
Inbound Comparison Mask Registers (PICMRx).”
2–1
Type
Hardwired to 00 to indicate that the address can be located anywhere in 32-bit
address space.
0
Memory space indicator Address is mapped to memory space (hardwired to 0).
9.11.2.15 Subsystem Vendor ID Register
Figure 9-47 and Table 9-34 describe the subsystem vendor ID register.
15
0
Field
SVID
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x2C
Figure 9-47. Subsystem Vendor ID Register
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-55
PCI Bridge
Table 9-34. Subsystem Vendor ID Register Description
Bits
Name
Description
15–0
Vendor ID
Identifies the add-in board or subsystem where the PCI device resides.
9.11.2.16 Subsystem Device ID Register
Figure 9-48 and Table 9-35 describe the subsystem ID register.
15
0
Field
SDID
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x2E
Figure 9-48. Subsystem Device ID Register
Table 9-35. Subsystem Device ID Description Register
Bits
Name
Description
15–0
Subsystem ID
Identifies the add-in board or subsystem where the PCI device resides.
9.11.2.17 PCI Bus Capabilities Pointer Register
Figure 9-49 and Table 9-36 describe the PCI bus capabilities pointer register.
7
0
Field
CP
Reset
0100_1000
R/W
R
Addr
0x34
Figure 9-49. PCI Bus Capabilities Pointer Register
Table 9-36. PCI Bus Capabilities Pointer Register Description
Bits
Name
Description
7–0
Capabilities pointer
Specifies the byte offset in the configuration space containing the first item in the
capabilities list.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-56
Freescale Semiconductor
PCI Bridge
9.11.2.18 PCI Bus Interrupt Line Register
Figure 9-50 and Table 9-37 describes the PCI bus interrupt line register.
7
0
Field
IL
Reset
0000_0000
R/W
R/W
Addr
0x3C
Figure 9-50. PCI Bus Interrupt Line Register
Table 9-37. PCI Bus Interrupt Line Register Description
Bits
Name
Description
7–0
Interrupt line
Contains the interrupt routing information. Software can use this register to hold
information regarding which input of the system interrupt controller the INTA
signal is attached to. Values in this register are specific to the system
architecture.
9.11.2.19 PCI Bus Interrupt Pin Register
Figure 9-51 and Table 9-38 describe the PCI bus interrupt pin register.
7
0
Field
IP
Reset
0000_0001
R/W
R
Addr
0x3D
Figure 9-51. PCI Bus Interrupt Pin Register
Table 9-38. PCI Bus Interrupt Pin Register Description
Bits
Name
Description
7–0
Interrupt Pin
Indicates which interrupt pin the device (or function) uses (0x01 = INTA).
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-57
PCI Bridge
9.11.2.20 PCI Bus MIN GNT
Figure 9-52 and Table 9-39 describes the PCI bus MIN GNT register.
7
0
Field
MIN GNT
Reset
0000_0000
R/W
R
Addr
0x3E
Figure 9-52. PCI Bus MIN GNT
Table 9-39. PCI Bus MIN GNT Description
Bits
Name
Description
7–0
MIN GNT
Specifies the length of the device’s burst period. The value 0x00 indicates that
the PCI bridge has no major requirements for the settings of latency timers.
9.11.2.21 PCI Bus MAX LAT
Figure 9-53 and Table 9-40 describe the PCI bus MAX LAT register.
7
0
Field
MAX LAT
Reset
0000_0000
R/W
R
Addr
0x3F
Figure 9-53. PCI Bus MAX LAT
Table 9-40. PCI Bus MAX LAT Description
Bits
Name
Description
7–0
MAX LAT
Specifies how often the device needs to gain access to the PCI bus. The value
0x00 indicates that the PCI bridge has no major requirements for the settings of
latency timers.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-58
Freescale Semiconductor
PCI Bridge
9.11.2.22 PCI Bus Function Register
The PCI bus function register, shown in Figure 9-54, is used to determine the configuration of the PCI bus
interface.
15
6
Field
—
5
CFG_LOCK
Reset
4
3
—
2
1
0
TRGT_
MSTR_
PCI_HA
LATENCY_DIS LATENCY_DIS
0000_0000_0010_0000
R/W
R/W
Addr
R
0x44
Figure 9-54. PCI Bus Function Register
Table 9-41 describes PCI bus function register fields.
Table 9-41. PCI Bus Function Register Field Descriptions
Bits
Name
Description
15–6
—
5
CFG_LOCK
Reserved, should be cleared.
Agent mode: Setting CFG_LOCK prevents an external PCI master from
accessing the configuration space while the 60x bus is doing internal
configuration. It is explicitly set and cleared by the 60x bus.
0 PCI bridge accepts accesses to the PCI configuration space or the internal
memory-mapped configuration space.
1 PCI bridge retries all accesses to the PCI configuration space or the internal
memory-mapped configuration space.
Host mode: the PCI configuration space is not accessible from the PCI side
when the device is in host mode; therefore, this bit applies only for the internal
memory-mapped configuration space.
0 PCI bridge accepts accesses to the internal memory-mapped configuration
space.
1 PCI bridge retries all accesses to the internal memory-mapped configuration
space.
4-3
—
Reserved, should be cleared.
2
TRGT_LATENCY_DIS
Target latency time-out disable. Controls whether the PCI bridge as a target
time-outs when the first data phase of a transaction has not completed in 16 PCI
cycles.
0 Target latency time-out enabled.
1 Target latency time-out disabled.
1
MSTR_LATENCY_DIS
Master latency timer disable. Controls whether the PCI bridge as a master ends
a transaction after the expiration of the master latency timer. See
Section 9.11.2.10, “PCI Bus Latency Timer Register.”
0 Master latency timer enabled.
1 Master latency timer disabled.
0
PCI_HA
Set or cleared by a Power-On configuration bit on power-up and is read-only.
0 PCI interface is in host mode
1 PCI interface is in agent mode
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-59
PCI Bridge
9.11.2.23 PCI Bus Arbiter Configuration Register
The PCI bus arbiter configuration register, shown in Figure 9-55, is used to determine the configuration of
the PCI bus arbiter. Only 1-byte or 2-byte accesses to address offset 0x46 are allowed.
15
Field
14
13
PCI_
PM
ARB_DIS
—
6
4
PCI_BUSMP
3
1
—
0
PCI_
BRIDGE MP
01000_0000_0000_0000
Reset
1
7
R/W
R/W
Addr
0x46
Reset value determined by PIC_CFG[1] pin value after hard reset. Refer to Table 9-42.
Figure 9-55. PCI Bus Arbiter Configuration Register
Table 9-42 describes the PCI bus arbiter configuration register fields.
Table 9-42. PCI Bus Arbiter Configuration Register Field Description
Bit
15
Name
Description
PCI_ARB_DIS
Determines if the PCI bridge is the PCI arbiter on the PCI bus. Set or cleared by
(PCI_CFG[1] pin value) the PIC_CFG[1] pin value after hard reset.
0 PCI bridge is the PCI arbiter.
1 PCI bridge is not the PCI arbiter. The PCI bridge presents its request on REQ0
to the external arbiter and receives its grant on GNT0.
14
Parking Mode
13–7
—
6-4
PCI Bus Master
Priorities
3–1
—
0
PCI Bridge Master
Priority
Controls which device receives the bus grant when there are no outstanding bus
requests and the bus is idle.
0 The bus is parked with the last device to use the bus.
1 The bus is parked with the PCI bridge.
Reserved, should be cleared.
Determines the arbitration priority given to the different masters on the PCI bus.
Bit 6 corresponds to the priority of the master sourcing REQ0, bit 5 corresponds
to REQ1, and bit 4 corresponds to REQ2.
0 Master n has a low priority.
1 Master n has a high priority.
Reserved, should be cleared.
Determines the PCI bridge’s arbitration priority.
0 The PCI bridge has a low priority.
1 The PCI bridge has a high priority.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-60
Freescale Semiconductor
PCI Bridge
9.11.2.24 PCI Hot Swap Register Block
The PCI Hot Swap register block, shown in Figure 9-56, is a set of registers in a capability structure. It
contains the Hot Swap control status register itself, as well as other fields as required by the capabilities
list format.
31
24
Field
23
16
HS_CSR (See Section 9.11.2.25, “PCI Hot Swap
Control Status Register.”)
—
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x4A
15
8
Field
7
0
NXT_PTR
CAP_ID
Reset
0000_0000_0000_0110
R/W
R/W
R
Addr
0x48
Figure 9-56. Hot Swap Register Block
Table 9-43 describes the Hot Swap register block fields.
Table 9-43. Hot Swap Register Block Field Descriptions
Bits
Name
Description
31–24
—
23–16
HS_CSR
Hot Swap control status register; see Section 9.11.2.25, “PCI Hot Swap Control
Status Register.”
15–8
NXT_PTR
Next pointer—an offset into the device’s PCI configuration space for the location
of the next item in the capabilities linked list. A value of 0x00 indicates that this is
the last item in the list.
7–0
CAP_ID
Reserved. Should be cleared.
CompactPCI ® Hot Swap capability ID (read only).
9.11.2.25 PCI Hot Swap Control Status Register
Figure 9-57 and Table 9-44 describe the Hot Swap control status register.
Field
23
22
INS
EXT
Reset
21
20
—
19
18
17
16
LOO
—
EIM
—
0000_0000
R/W
R/W
Addr
0x4A
Figure 9-57. Hot Swap Control Status Register
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-61
PCI Bridge
Table 9-44. Hot Swap Control Status Register Field Descriptions
Bit
Name
Description
23
INS
ENUM status: insertion. Write a ‘1’ to clear this bit.
0 ENUM is not asserted
1 ENUM is asserted
22
EXT
ENUM status: extraction. Write a ‘1’ to clear this bit.
0 ENUM is not asserted
1 ENUM is asserted
21–20
—
19
LOO
18
—
17
EIM
16
—
Reserved. Should be cleared.
LED on/off when the hardware is in state H2. Read/write-able.
0 LED off
1 LED on
Reserved. Should be cleared.
ENUM signal mask. Read/write-able.
0 Enable signal
1 Mask signal
Reserved. Should be cleared.
9.11.2.26 PCI Configuration Register Access from the Core
The 60x bus master cannot directly access the PCI configuration registers because they are not in the
internal memory-mapped configuration register’s space. The 60x bus master must first load CFG_ADDR
(at offset 0x10900 in the memory-mapped configuration registers block) with a 32-bit register address in
the form ‘0x8000_0nnn,’ where nnn is the address offset of the desired PCI configuration register. The data
can then be accessed in CFG_DATA (at offset 0x10904 in the internal memory map). See
Section 9.9.1.4.4, “Host Mode Configuration Access.”
When accessing the PCI bridge’s PCI configuration registers with the 60x bus master, note the following:
• The bus number and device number fields of the CFG_ADDR register should be cleared.
• Accesses to CFG_ADDR or CFG_DATA which are greater than 4 bytes generate an illegal register
access error setting ECR[IRA]; see Section 9.11.1.11, “Error Control Register (ECR).”
• Accesses to CFG_DATA without a valid offset in CFG_ADDR generates an I/O transaction on the
PCI bus.
9.11.2.27 PCI Configuration Register Access in Big-Endian Mode
Since the local CPU (internal core or external) is operating in big-endian mode, software must byte-swap
the data of the configuration register before performing an access. That is, the data appears in the core
register in ascending significance byte order (LSB to MSB). Software loads the configuration register
address and the configuration register data into the core register in ascending significance byte order (LSB
to MSB).
Note that in the following examples, the data in the configuration register (at 0x18) is shown in
little-endian order. This is because all the internal registers are intrinsically little-endian.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-62
Freescale Semiconductor
PCI Bridge
Example: configuration sequence, 2-byte data write to register at address offset 0x1A for PCI bus.
Initial values:
r0 contains 0x1800_0080
r1 contains IMMR+0x10900
r2 contains IMMR+0x10904
r3 contains 0xDDCC_BBAA
Register at 0x18 contains 0xFFFF_FFFF (1B to 18)
Code sequence:
stw
r0,0(r1)
sth
r3,2(r2)
Results: Address IMMR+0x10900 contains 0x8000_0018 (MSB to LSB)
Address IMMR+0x10904 contains 0xXXXX_AABB (MSB to LSB) where ‘XXXX’ is
the old value and is not affected the sth.
Note: the address of PCI_CFG_DATA must match the offset address 0x1A.
Register at 0x18 contains 0xAABB_FFFF (1B to 18)
This example shows an address of IMMR+0x10906 used to access the PCI_CFG_DATA. This was done
in order to align the data with the address 0x1A. The address used to access PCI_CFG_DATA can have a
value of IMMR+0x10904, IMMR+0x10905, IMMR+0x10906, or IMMR+0x10907. The two least
significant bits of the address used to access PCI_CFG_DATA should match the byte-wise offset of the
register being accessed. For instance, if 0x0D is the offset of the register being accessed, then the address
used to access PCI_CFG_DATA must be IMMR+0x10905.
9.11.2.27.1
Additional Information on Endianess
The endianess of both the MPC8280's peripheral logic (GPCR[LE_MODE]—see the following section)
and the MPC8280's 603e CPU core (MSR[LE]) must be set to the same endianess configuration—that is
both must be set for little or big endian operation.
For applications where little endian (LE) devices, such as those commonly found on the PCI bus, share
memory with the MPC8280, it is recommended to leave the MPC8280's 603e core CPU and peripheral
logic in the big endian (BE) modes and then to use a region of the MPC8280 local memory for
LE-formatted data. When a little endian PCI device stores data to this memory region, the MPC8280
internal peripheral logic (in big endian mode) stores the data into memory in LE format. Likewise, when
a little-endian PCI device reads data from this memory region, the MPC8280 internal peripheral logic (in
BE mode) provides the data to the PCI device in LE format.
A little-endian PCI device can share this LE memory region with the MPC8280 local processor (603e core
CPU) running in big endian if, when the MPC8280 accesses that LE region, it uses the lwbrx and stwbrx
commands. The lwbrx command byte-swaps the LE data from that region so the 603e CPU sees the data
in BE format. Similarly, the stwbrx command byte-swaps the BE data from the 603e processor being
stored to that region of memory, so it is stored into the memory region in LE format.
For the MPC603e and the MPC8280 implementations, there is NO latency difference associated with
lwbrx and stwbrx commands compared to the other load and store commands.
9.11.2.27.2
Notes on GPCR[LE_MODE]
GPCR[LE_MODE] (refer to Section 9.11.1.7) determines the endianess of the PCI section of MPC8280.
The default value of GPCR[LE_MODE] (offset: 0x1087C) is 0. If LE_MODE is set while a program is
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-63
PCI Bridge
executing, care should be taken as to how subsequent accesses to the PCI memory-mapped registers are
made. Consider the following two examples (assume internal memory starts at 0x04700000):
Example 1— Accessing PCI memory-mapped registers before GPCR[LE_MODE] is set. Assume that
one wants to use CPU software to set CTM of PCI DMA0 mode register
(DMAMR0[CTM]) located at 0x04710500. The value constructed from the bit field
description of the DMAMR0 is 0x00000004. However, the value written to this register is
0x04000000—the byte-swapped version of 0x00000004.
Example 2— Accessing PCI memory-mapped registers after GPCR[LE_MODE] is set. Assume that,
after GPCR[LE_MODE] is set, one wants to use CPU software to set DMAMR0[CTM].
Because of address munging, this register is now located at 0x04710504. This new address
is derived from the following:
1.The register is located at 0x04710500.
2.For a 4-byte access, address munging dictates that the XOR value is 0b100 (refer to
Chapter 4 of the Programming Environments Manual for 32-Bit Implementations of
the PowerPC Architecture).
3.The last three bits of 0x04710500 is 0b000.
4.XOR 0b000 with 0b100 (0b000 ⊕ 0b100 = 0b100).
5.Therefore, the munged address of this register would be 0x04710504.
Therefore, to set CTM in PCI DMA0 mode register, 0x00000004 is written to 0x04710504.
9.11.2.28 Initializing the PCI Configuration Registers
The configuration registers are initialized to the reset values shown in the register descriptions. However,
they can also be initialized to user-defined values loaded directly from the EEPROM used to configure the
MPC8280 by setting the ALD_EN (auto-load enable) bit in the hard reset configuration word; refer to
Section 5.4.1, “Hard Reset Configuration Word.”
To initialize configuration registers from an EEPROM, the user builds a contiguous table of register
initialization data structures in a user-defined space within the EEPROM. Each data structure, shown in
Figure 9-58, contains the address of a specific register and its initialization data, as well as some control
information. The last data structure entry in the table is marked by setting its ‘Last’ bit.
Offset from the table
start address
0
28
0x00
0x04
29
30
31
Destination address
—
Last
0x08
Destination data
0x0C
•
•
•
Size[1:0]
Figure 9-58. Data Structure for Register Initialization
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-64
Freescale Semiconductor
PCI Bridge
Table 9-45 describes the data structure fields.
Table 9-45. Bit Settings for Register Initialization Data Structure
Offset
Bits
Name
Description
0x00
0–31
Address
Contains the absolute destination address to which the data is written.
0x04
0–28
—
29
Last
Indicates that this is the last initialization transaction to be performed.
0 Not last transaction
1 Last transaction
30–31
SIZE
Data size in bytes
00 4 bytes
01 1 byte
10 2 bytes
11 3 bytes
0–31
Data
Contains the data to be written to the specified address. Data bytes are
written according to the value specified in the SIZE field and according
to big-endian byte ordering.
0x08
Reserved, should be cleared.
Note that the data structure description assumes the following:
• Addresses refer to 60x bus addresses.
• Address and data byte ordering are big-endian.
• Accesses to PCI configuration registers are indirect (through PCI CFG_ADDR and PCI
CFG_DATA).
A pointer located at address 0x4 of the EEPROM (right after the hard reset configuration word) defines
the beginning of the initialization table. The table should be placed beyond the reset configuration data to
avoid the EEPROM bytes dedicated to the eight possible hard reset configuration words (refer to
Section 5.4.1, “Hard Reset Configuration Word,” and Figure 9-59).
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-65
PCI Bridge
EEPROM start address + 0x00
0x04
Configuration byte
Init Table Pointer
0x08
Configuration byte
0x10
Configuration byte
Init Table Pointer + 0x00
Address, data, size
+0x0C
Address, data, size
+0x1A
+0x28
Address, data, size
Address, data, size,
LAST
Figure 9-59. PCI Configuration Data Structure for the EEPROM
After a hard reset, if the auto-load enable bit has been set in the hard reset configuration word, a special
internal CP routine checks the EEPROM contents and loads the configuration data into the specified
addresses. Note that the initialization data can be loaded into any memory location (not restricted to the
PCI configuration space) by this routine.
9.12
Message Unit (I2O)
The embedded processor is often part of a larger system containing many processors and distributed
memory. These processors tend to work on tasks independent of the host processor(s) and other peripheral
processors in the system. Because of the independent nature of the tasks, it is necessary to provide a
communication mechanism between the peripheral processors and the rest of the system. One such method
is the use of messages. The PCI bridge provides a messaging unit to further facilitate communications
between host and peripheral. The PCI bridge’s message unit can operate with either generic messages and
door bell registers, or as an I2O interface.
9.12.1
Message Registers
The PCI bridge contains two inbound message registers and two outbound message registers. The registers
are each 32 bits. The inbound registers allow a remote host or PCI master to write a 32-bit value which in
turn causes an interrupt to the local processor that implements the PowerPC architecture because the
register indirectly drives an interrupt line to the local processor. The outbound register allows the local
processor to write an outbound message which, in turn, causes the outbound interrupt signal INTA to
assert.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-66
Freescale Semiconductor
PCI Bridge
The interrupt to the local processor is cleared by setting the appropriate bit in the inbound message
interrupt status register. The interrupt to PCI (INTA) is cleared by setting the appropriate bit in the
outbound interrupt status register.
9.12.1.1
Inbound Message Registers (IMRx)
The inbound message registers, described in Figure 9-60 and Figure 9-46, are accessible from the PCI bus
and the 60x bus in both host and agent modes.
31
16
Field
IMSGx
Reset
Undefined
R/W
R/W
Addr
0x10452 (IMR0); 0x10456 (IMR1)
15
0
Field
IMSGx
Reset
Undefined
R/W
R/W
Addr
0x10450 (IMR0); 0x10454 (IMR1)
Figure 9-60. Inbound Message Registers (IMRx)
Table 9-46. IMRx Field Descriptions
Bits
Name
31–0
IMSG x
9.12.1.2
Description
Inbound message x. Contains generic data to be passed between the local
processor and external hosts.
Outbound Message Registers (OMRx)
The outbound message registers, described in Figure 9-61 and Figure 9-47, are accessible from the PCI
bus and the 60x bus in both host and agent modes.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-67
PCI Bridge
31
16
Field
OMSGx
Reset
Undefined
R/W
R/W
Addr
0x1045A (OMR0); 0x1045E (OMR1)
15
0
Field
OMSGx
Reset
Undefined
R/W
R/W
Addr
0x10458 (OMR0); 0x1045C (OMR1)
Figure 9-61. Outbound Message Registers (OMRx)
Table 9-47. OMRx Field Descriptions
Bits
Name
31–0
OMSGx
9.12.2
Description
Outbound message x. Contains generic data to be passed between the local
processor and external hosts.
Door Bell Registers
The PCI bridge contains an inbound and an outbound door bell register. The registers are 32-bit. The
inbound door bell allows a remote processor to set a bit in the register from the PCI bus. This, in turn,
causes the PCI bridge to generate an interrupt to the local processor. The local processor can write to the
outbound register which causes the outbound interrupt signal INTA to assert thus interrupting the remote
processor on the PCI bus.
9.12.2.1
Outbound Doorbell Register (ODR)
ODR, described in Figure 9-62 and Table 9-48, is accessible from the PCI bus and the 60x bus in both host
and agent modes.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-68
Freescale Semiconductor
PCI Bridge
31
29
Field
28
16
ODRx
—
Reset
0000_0000_0000_0000
R/W
Refer to Table 9-48.
Addr
0x10462
15
0
Field
ODRx
Reset
0000_0000_0000_0000
R/W
Refer to Table 9-48.
Addr
0x10460
Figure 9-62. Outbound Doorbell Register (ODR)
Table 9-48. ODR Field Descriptions
Bits
Name
Access
31–29
—
R
Reserved, should be cleared.
ODRx Write 1 to set from local processor. Outbound door bell x, where x is each bit. Writing a bit in
Write 1 to clear from PCI.
this register from the local processor causes an interrupt
(INTA) to be generated.
28–0
9.12.2.2
Description
Inbound Doorbell Register (IDR)
IDR, described in Figure 9-63 and Table 9-49, is accessible from the PCI bus and the 60x bus in both host
and agent modes.
31
30
Field IMC
Reset
16
IDRx
0000_0000_0000_0000
R/W
R/W
Addr
0x1046A
15
0
Field
IDRx
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x10468
Figure 9-63. Inbound Doorbell Register (IDR)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-69
PCI Bridge
Table 9-49. IDR Field Descriptions
Bits
Name
Access
Description
31
IMC
Write 1 to set from PCI.
Machine check. Writing to this bit will generate a machine
Write 1 to clear from local processor. check interrupt to the local processor.
30–0
IDRx
Write 1 to set from PCI.
Inbound door bell x, where x is each bit. Writing a bit in this
Write 1 to clear from local processor. register from the PCI bus causes an interrupt to be
generated through the PCI bridge to the local processor.
9.12.3
I2O Unit
The Intelligent Input Output specification (I2O) was established in the industry to allow
architecture-independent I/O subsystems to communicate with an OS through an abstraction layer. The
specification is centered around a message passing scheme. An I2O embedded peripheral (IOP) is
comprised of memory, processor, and input/output device(s). An IOP dedicates space in its local memory
to hold inbound (from the remote host) and outbound (to the remote host) messages. The space is managed
as memory-mapped FIFOs, with pointers to this memory maintained in hardware.
Messages are made up of frames which are a minimum of 64-bytes in length. The message frame address
(MFA) is the address which points to the first byte of the message frame. The messages are located in
local-system memory. Tracking of the status and location of these messages is done with four FIFOs (two
FIFOs for inbound and two for outbound messages) also located in local-system memory. Hardware
registers inside the PCI bridge’s core logic manage these FIFOs. One FIFO in each queue keeps track of
the free MFAs (Free_LIST FIFO). The other FIFO keeps track of the MFAs which have posted messages
(Post_LIST FIFO). Figure 9-64 shows an example of the message queues, although there is no specific
order that these queues must follow.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-70
Freescale Semiconductor
PCI Bridge
Local memory
Inbound free list FIFO
Local processor write
Head pointer
MFA
MFA
MFA
Inbound post list FIFO
Tail pointer
PCI master read
PCI master write
Inbound
queue
port
Local processor read
Head pointer
MFA
MFA
MFA
MFA
Tail pointer
MFA
Outbound free list FIFO
Local processor read
Head pointer
PCI master write
PCI master read
MFA
MFA
MFA
Outbound post list FIFO
Tail pointer
Outbound
queue
port
Head pointer
Local processor write
Tail pointer
MFA
MFA
MFA
MFA
MFA
Message
frame
Message
frame
Message
frame
Message
frame
Message
frame
Message
frame
Message
frame
Message
frame
Message
frame
Message
frame
Message
frame
Message
frame
Message
frame
Message
frame
Message
frame
Message
frame
Figure 9-64. I2O Message Queue
I2O defines extensions for the PCI bus hardware through which message queues are managed in hardware.
9.12.3.1
PCI Configuration Identification
A host identifies an IOP by its PCI class code. When I2O is enabled, configuration information is provided
through the PCI configuration space to the host. Refer to the following:
• Section 9.11.2.6, “PCI Bus Programming Interface Register”
• Section 9.11.2.7, “Subclass Code Register”
• Section 9.11.2.8, “PCI Bus Base Class Code Register”
9.12.3.2
Inbound FIFOs
The inbound FIFO allows external PCI masters to post messages to the local processor. I2O defines two
inbound FIFOs—an inbound post FIFO and an inbound free FIFO.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-71
PCI Bridge
The following registers should be accessed only from the 60x bus and only in agent mode. Accesses while
in host mode or from the PCI bus have undefined results.
9.12.3.2.1
Inbound Free_FIFO Head Pointer Register (IFHPR) and
Inbound Free_FIFO Tail Pointer Register (IFTPR)
The inbound free list FIFO holds the list of empty inbound MFAs. The external PCI master reads IFQPR
(refer to Section 9.12.3.4.1, “Inbound FIFO Queue Port Register (IFQPR)”) which returns the MFA
pointed to by the inbound free list tail pointer register, (IFTPR+QBAR). The PCI bridge’s I2O unit then
advances IFTPR.
If the inbound free list is empty (no free MFA entries), the unit returns 0xFFFF_FFFF.
Free MFAs from the local processor are posted to the inbound free list FIFO that is pointed to by the
inbound free_FIFO head pointer register, described in Figure 9-65 and Table 9-50. The local processor is
responsible for updating this register.
31
20
Field
19
16
QBA
Reset
IFHP
0000_0000_0000_0000
R/W
R
R/W
Addr
0x104A2
15
2
Field
IFHP
Reset
1
0
—
0000_0000_0000_0000
R/W
R
R/W
Addr
0x104A0
Figure 9-65. Inbound Free_FIFO Head Pointer Register (IFHPR)
Table 9-50. IFHPR Field Descriptions
Bits
Name
Description
31–20
QBA
Queue base address. When read returns the contents of QBAR bits 31-20.
19–2
IFHP
Inbound free_fifo head pointer. Local memory offset of the head pointer of the inbound free list
FIFO.
1–0
—
Reserved, should be cleared.
Free MFAs are picked up by the PCI masters that are pointed to by the inbound free_FIFO tail pointer,
described in Figure 9-66 and Table 9-51. The PCI read is performed at the inbound queue port. Hardware
automatically advances this register after every read.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-72
Freescale Semiconductor
PCI Bridge
31
20
Field
19
16
QBA
Reset
IFTP
0000_0000_0000_0000
R/W
R
R/W
Addr
0x104AA
15
2
Field
IFTP
Reset
1
0
—
0000_0000_0000_0000
R/W
R
R/W
Addr
0x104A8
Figure 9-66. Inbound Free_FIFO Tail Pointer Register (IFTPR)
Table 9-51. IFTPR Field Descriptions
Bits
Name
31–20
QBA
Queue base address. When read returns the contents of QBAR bits 31-20.
19–2
IFTP
Inbound free_FIFO tail pointer. Local memory offset of the tail pointer of the inbound free list FIFO.
1–0
—
9.12.3.2.2
Description
Reserved, should be cleared.
Inbound Post_FIFO Head Pointer Register (IPHPR) and
Inbound Post_FIFO Tail Pointer Register (IPTPR)
The inbound post FIFO holds MFAs from external PCI masters which are posted to the local processor.
PCI masters, external to the PCI bridge, write to the head of the FIFO by writing the MFA to IFQPR (refer
to Section 9.12.3.4.1, “Inbound FIFO Queue Port Register (IFQPR)”). The I2O unit transfers the MFA to
the location pointed to by the IPHPR. The local address is QBAR + IPHPR.
Once the MFA has been written to the queue in local memory, the PCI bridge’s I2O unit advances the
IPHPR to set up for the next message. This causes an interrupt to be asserted to the local processor. The
inbound post queue interrupt bit in the inbound interrupt status register (IMISR[IPQI]) is set to indicate
this condition (refer to Table 9-62). The local processor acknowledges the message (i.e. MFA) by writing
a one to the appropriate status bit (IMISR[IPQI]) to clear it. The local processor fetches the MFA by
reading the contents of the IPTPR. After the local processor has read the message pointed to by the MFA,
the local processor must advance the IPTPR. Once the processor has completed use of the message, it must
return the message buffer (i.e. MFA) to the inbound free list FIFO.
PCI masters post MFAs to the inbound post list FIFO that is pointed to by the inbound post_FIFO head
pointer register, described in Figure 9-67 and Table 9-52. The PCI writes are addressed to the inbound
queue port. Hardware (in the I2O module) automatically advances the IPHPR after every write.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-73
PCI Bridge
31
Field
20
19
16
QBA
Reset
IPHP
0000_0000_0000_0000
R/W
R
R/W
Addr
0x104B2
15
2
Field
1
IPHP
Reset
0
—
0000_0000_0000_0000
R/W
R
R/W
Addr
0x104B0
Figure 9-67. Inbound Post_FIFO Head Pointer Register (IPHPR)
Table 9-52. IPHPR Field Descriptions
Bits
Name
Description
31–20
QBA
Queue base address. When read returns the contents of QBAR bits 31-20.
19–2
IPHP
Inbound post_FIFO head pointer. Local memory offset of the head pointer of the inbound post list FIFO.
1–0
—
Reserved, should be cleared.
MFAs posted by PCI hosts are picked up by the local processor via the inbound post_FIFO tail pointer
register, described in Figure 9-68 and Table 9-53. The local processor is responsible for updating this
register.
31
Field
20
19
QBA
Reset
IPTP
0000_0000_0000_0000
R/W
R
R/W
Addr
0x104BA
15
Field
Reset
R/W
Addr
16
2
IPTP
1
0
—
0000_0000_0000_0000
R
R/W
0x104B8
Figure 9-68. Inbound Post_FIFO Tail Pointer Register (IPTPR)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-74
Freescale Semiconductor
PCI Bridge
Table 9-53. IPTPR Field Descriptions
Bits
Name
31–20
QBA
Queue base address. When read returns the contents of QBAR bits 31-20.
19–2
IPTP
Inbound post_FIFO tail pointer. Local memory offset of the tail pointer of the inbound post list
FIFO.
1–0
—
9.12.3.3
Description
Reserved, should be cleared.
Outbound FIFOs
The outbound queues are used to send messages from the local processor to a remote host processor. I2O
defines two outbound FIFOs—an outbound post FIFO and an outbound free FIFO.
The following registers should be accessed only from the 60x bus and only in agent mode. Accesses while
in host mode or from the PCI bus have undefined results.
9.12.3.3.1
Outbound Free_FIFO Head Pointer Register (OFHPR) and
Outbound Free_FIFO Tail Pointer Register (OFTPR)
The outbound free list FIFO holds the MFAs of the empty outbound message locations in local memory.
When the local processor is ready to send an outbound message, it first fetches an empty MFA by reading
the OFTPR. It then writes the message into the MFA. The OFTPR is managed by the local processor.
When an external PCI master has completed use of a message that was posted in the outbound post FIFO
and wants to return the MFA to the free list, it writes to OFQPR (refer to Section 9.12.3.4.2, “Outbound
FIFO Queue Port Register (OFQPR)”). The PCI bridge’s I2O unit then writes the MFA to the OFHPR.
This, in turn, causes the outbound free head pointer to be advanced.
Free MFAs are returned by the PCI masters to the outbound free list FIFO that is pointed to by the
outbound free_FIFO head pointer register, described in Figure 9-69 and Table 9-54. The PCI write
references the outbound queue port. The I2O hardware automatically advances the address, (i.e. OFHPR)
after every write.
31
20
Field
19
QBA
Reset
16
OFHP
0000_0000_0000_0000
R/W
R
R/W
Addr
0x104C2
15
2
Field
OFHP
Reset
1
0
—
0000_0000_0000_0000
R/W
R
R/W
Addr
0x104C0
Figure 9-69. Outbound Free_FIFO Head Pointer Register (OFHPR)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-75
PCI Bridge
Table 9-54. OFHPR Field Descriptions
Bits
Name
31–20
QBA
19–2
OFHP
1–0
—
Description
Queue base address. When read returns the contents of QBAR.
Outbound free_FIFO head pointer. Local memory offset of the head pointer of the outbound free
list FIFO.
Reserved, should be cleared.
Free MFAs are picked up by the local processor pointed to by the outbound free_FIFO tail pointer register,
described in Figure 9-70 and Table 9-55. This register is updated by the local processor.
31
20
Field
19
QBA
Reset
16
OFTP
0000_0000_0000_0000
R/W
R
R/W
Addr
0x104CA
15
2
Field
OFTP
Reset
1
0
—
0000_0000_0000_0000
R/W
R
R/W
Addr
0x104C8
Figure 9-70. Outbound Free_FIFO Tail Pointer Register (OFTPR)
Table 9-55. OFTPR Field Descriptions
Bits
Name
31–20
QBA
Queue base address. When read returns the contents of QBAR bits 31-20.
19–2
OFTP
Outbound free_FIFO tail pointer. Local memory offset of the tail pointer of the outbound free list
FIFO.
1–0
—
9.12.3.3.2
Description
Reserved, should be cleared.
Outbound Post_FIFO Head Pointer Register (OPHPR) and
Outbound Post_FIFO Tail Pointer Register (OPTPR)
The outbound post FIFO holds MFAs which are posted from the local processor to external processors.
The local processor places messages in the outbound post FIFO by writing to the MFA to OPHPR +
QBAR. The local processor must then advance the OPHPR.
The PCI bridge’s PCI interrupt is generated (INTA) when the FIFO is not empty (head and tail pointers are
not equal). The outbound post queue interrupt bit is set in the outbound interrupt status register. The status
bit is cleared when the head and tail pointers are equal. The interrupt can be masked using the outbound
interrupt mask register.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-76
Freescale Semiconductor
PCI Bridge
An external PCI master reads the outbound queue port register. This causes the PCI bridge’s I2O unit to
read the MFA from local memory pointed to by the OPTPR+QBAR. The unit then advances the OPTPR.
When the FIFO is empty (head and tail pointers are equal), the unit returns 0xFFFF_FFFF.
The local processor posts MFAs to the outbound post list FIFO that is pointed to by the outbound
post_FIFO head pointer register, described in Figure 9-71 and Table 9-56. The local processor is
responsible for updating this register.
31
20
Field
19
QBA
Reset
16
OPHP
0000_0000_0000_0000
R/W
R
R/W
Addr
0x104D2
15
2
Field
OPHP
Reset
1
0
—
0000_0000_0000_0000
R/W
R
R/W
Addr
0x104D0
Figure 9-71. Outbound Post_FIFO Head Pointer Register (OPHPR)
Table 9-56. OPHPR Field Descriptions
Bits
Name
31–20
QBA
19–2
OPHP
1–0
—
Description
Queue base address. When read returns the contents of QBAR bits 31-20.
Outbound post_FIFO head pointer. Local memory offset of the head pointer of the outbound
post list FIFO.
Reserved, should be cleared.
Posted MFAs are picked up by PCI hosts that are pointed to by the outbound post_FIFO tail pointer
register, described in Figure 9-72 and Table 9-57. The PCI read is performed at the outbound queue port.
Hardware automatically advances this register after every read.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-77
PCI Bridge
31
20
Field
19
16
QBA
Reset
OPTP
0000_0000_0000_0000
R/W
R
R/W
Addr
0x104DA
15
2
Field
OPTP
Reset
1
0
—
0000_0000_0000_0000
R/W
R
R/W
Addr
0x104D8
Figure 9-72. Outbound Post_FIFO Tail Pointer Register (OPTPR)
Table 9-57. OPTPR Field Descriptions
Bits
Name
31–20
QBA
Queue base address. When read returns the contents of QBAR bits 31-20.
19–2
OPTP
Outbound post_FIFO tail pointer. Local memory offset of the tail pointer of the outbound post
list FIFO.
1–0
—
9.12.3.4
Description
Reserved, should be cleared.
I2O Registers
The following sections discuss I2O registers.
9.12.3.4.1
Inbound FIFO Queue Port Register (IFQPR)
IFQPR is used by PCI masters to access inbound messages in local memory. Local processor does not have
access to this port. IFQPR should be accessed only from the PCI bus. IFQPR is described in Figure 9-73
and Table 9-58.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-78
Freescale Semiconductor
PCI Bridge
31
16
Field
IFQP
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x10442
15
0
Field
IFQP
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x10440
Figure 9-73. Inbound FIFO Queue Port Register (IFQPR)
Table 9-58. IFQPR Field Descriptions
Bits
Name
Description
31–0
IFQP
Inbound FIFO queue port. Reading this register will return the MFA from inbound free
list FIFO. Writing to this register will post the MFA to the inbound post list FIFO.
9.12.3.4.2
Outbound FIFO Queue Port Register (OFQPR)
OFQPR is used by PCI masters to access outbound messages in local memory. Local processor does not
have access to this port. OFQPR should be accessed only from the PCI bus. OFQPR is described in
Figure 9-74 and Table 9-59.
31
16
Field
OFQP
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x10446
15
0
Field
OFQP
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x10444
Figure 9-74. Outbound FIFO Queue Port Register (OFQPR)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-79
PCI Bridge
Table 9-59. OFQPR Field Descriptions
Bits
Name
Description
31–0
OFQP
Outbound FIFO queue port. Reading this register will return the MFA from outbound
post list FIFO. Writing this register will post the MFA to the outbound free list FIFO.
9.12.3.4.3
Outbound Message Interrupt Status Register (OMISR)
OMISR contains the interrupt status of the I2O, door bell, and outbound message registers. A PCI device
acknowledges the outbound message interrupt by writing a 1 to the appropriate status bit: OMISR[OM1I]
or OMISR[OM0I]. This clears both the interrupt and the corresponding status bit. The local processor
provokes an outbound message interrupt by writing to either of the two outbound message registers:
OMR0 or OMR1. OMISR should be accessed only from the PCI bus IFQPR should be accessed only from
the PCI bus.
31
16
Field
—
Reset
0000_0000_0000_0000
R/W
Refer to Table 9-60.
Addr
0x10432
15
6
Field
—
Reset
5
4
3
2
OPQI
—
ODI
—
1
0
OM1I OM0I
0000_0000_0000_0000
R/W
Refer to Table 9-60.
Addr
0x10430
Figure 9-75. Outbound Message Interrupt Status Register (OMISR)
Table 9-60 describes OMISR fields.
Table 9-60. OMISR Field Descriptions
Bits
31–6
Name
R/W
Description
—
R
Reserved, should be cleared.
5
OPQI
R
Outbound post queue interrupt. When set indicates that a message or messages
are posted in the outbound queue. To clear the interrupt, software has to read all
MFAs in the outbound post FIFO. This bit is set regardless of the state of the
OPQIM mask bit.1
4
—
R
Reserved, should be cleared.
3
ODI
R
Outbound doorbell interrupt. When set indicates that there is an outbound doorbell
interrupt.
2
—
R
Reserved, should be cleared.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-80
Freescale Semiconductor
PCI Bridge
Table 9-60. OMISR Field Descriptions (continued)
Bits
1
Name
R/W
Description
1
OM1I
Read/
Write 1
to clear
Outbound message 1 interrupt. When set indicates that there is an Outbound
message 1 interrupt.
0
OM0I
Read/
Write 1
to clear
Outbound message 0 interrupt. When set indicates that there is an Outbound
message 0 interrupt
Note that when conditions for the Outbound Post Queue Interrupt assertion are valid, and OMIMR[OPQIM] is set,
OMISR[OPQI] is cleared. The application should always clear OMIMR[OPQIM] before referring to the content of
OMISR[OPQI].
9.12.3.4.4
Outbound Message Interrupt Mask Register (OMIMR)
OMIMR contains the interrupt mask of the I2O, door bell, and message register events generated by the
local processor. OMIMR should be accessed only from the PCI bus.
31
16
Field
—
Reset
0000_0000_0000_0000
R/W
Refer to Table 9-61.
Addr
0x10436
15
6
Field
—
Reset
5
4
3
2
OPQIM
—
ODIM
—
1
0
OM1IM OM0IM
0000_0000_0000_0000
R/W
Refer to Table 9-61.
Addr
0x10434
Figure 9-76. Outbound Message Interrupt Mask Register (OMIMR)
Table 9-61 describes OMIMR fields.
Table 9-61. OMIMR Field Descriptions
Bits
Name
R/W
31–6
—
R
5
OPQIM
RW
4
—
R
3
ODIM
RW
2
—
R
Description
Reserved, should be cleared.
Outbound post queue interrupt mask
0 Outbound post queue interrupt is allowed.
1 Outbound post queue interrupt is masked.
Reserved, should be cleared.
Outbound doorbell interrupt mask
0 Outbound doorbell interrupt is allowed.
1 Outbound doorbell interrupt is masked.
Reserved, should be cleared.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-81
PCI Bridge
Table 9-61. OMIMR Field Descriptions (continued)
Bits
Name
R/W
1
OM1IM
RW
Outbound message 1 interrupt mask
0 Outbound message 1 interrupt is allowed.
1 Outbound message 1 interrupt is masked.
0
OM0IM
RW
Outbound message 0 interrupt mask
0 Outbound message 0 interrupt is allowed.
1 Outbound message 0 interrupt is masked.
9.12.3.4.5
Description
Inbound Message Interrupt Status Register (IMISR)
This register contains the interrupt status of the I2O, door bell, and message register events. Writing a 1 to
the corresponding set bit will clear the bit. The events are generated by the PCI masters. IMISR should be
accessed only from the 60x bus and only in agent mode. Accesses while in host mode or from the PCI bus
have undefined results.
31
16
Field
—
Reset
0000_0000_0000_0000
R/W
Refer to Table 9-62.
Addr
0x10482
15
9
Field
—
8
7
OFOI IPOI
Reset
6
5
4
3
2
1
0
—
IPQI
MCI
IDI
—
IM1I
IM0I
0000_0000_0000_0000
R/W
Refer to Table 9-62.
Addr
0x10480
Figure 9-77. Inbound Message Interrupt Status Register (IMISR)
Table 9-62 describes IMISR fields.
Table 9-62. IMISR Field Descriptions
Bits
Name
Access
Description
31–9
—
R
8
OFOI
R/Write 1
to clear
Outbound Free Overflow Interrupt. When set indicates that the Outbound
Free_FIFO Head pointer is equal to the Outbound Free_FIFO Tail pointer and
the queue is full. A machine check interrupt is generated.
7
IPOI
R/Write 1
to clear
Inbound Post Overflow Interrupt. When set indicates that the Inbound
Post_FIFO Head pointer is equal to the Inbound Post_FIFO Tail pointer and the
queue is full. A machine check interrupt is generated.
6
—
R
5
IPQI
R/Write 1
to clear
Reserved, should be cleared.
Reserved, should be cleared.
Inbound Post Queue Interrupt. When set indicates that the PCI master has
posted an MFA to the Inbound Post queue.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-82
Freescale Semiconductor
PCI Bridge
Table 9-62. IMISR Field Descriptions (continued)
Bits
Name
Access
Description
4
MCI
R
Machine check interrupt. When set indicates that a machine check interrupt
condition has been generated by setting the Inbound doorbell register’s bit 31.
The interrupt is cleared by resetting the Inbound doorbell register’s bit 31.
3
IDI
R
Inbound doorbell interrupt. When set indicates that there is an Inbound
Doorbell interrupt.
2
—
R
Reserved, should be cleared.
1
IM1I
R/Write 1
to clear
Inbound message 1 interrupt. When set indicates that there is an Inbound
message 1 interrupt.
0
IM0I
R/Write 1
to clear
Inbound message 0 interrupt. When set indicates that there is an Inbound
message 0 interrupt.
9.12.3.4.6
Inbound Message Interrupt Mask Register (IMIMR)
This register contains the interrupt mask of the I2O, door bell, and message register events generated by
the PCI master. IMIMR should be accessed only from the 60x bus and only in agent mode. Accesses while
in host mode or from the PCI bus have undefined results.
31
16
Field
—
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x10486
15
9
Field
—
8
7
6
OFOIM IPOIM
Reset
—
5
4
3
IPQIM MCIM IDIM
2
—
1
0
IM1IM IM0IM
0000_0000_0000_0000
R/W
R/W
Addr
0x10484
Figure 9-78. Inbound Message Interrupt Mask Register (IMIMR)
Table 9-63 describes IMIMR fields.
Table 9-63. IMIMR Field Descriptions
Bits
Name
Description
31–9
—
8
OFOIM
Outbound free overflow interrupt mask
0 Outbound free overflow interrupt is allowed.
1 Outbound free overflow interrupt is masked.
7
IPOIM
Inbound post overflow interrupt mask
0 Inbound post overflow interrupt is allowed.
1 Inbound post overflow interrupt is masked.
Reserved, should be cleared.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-83
PCI Bridge
Table 9-63. IMIMR Field Descriptions (continued)
Bits
Name
6
—
5
IPQIM
Inbound post queue interrupt mask
0 Inbound post queue interrupt is allowed.
1 Inbound post queue interrupt is masked.
4
MCIM
Machine check interrupt mask
0 Machine check interrupt from the inbound doorbell register is allowed.
1 Machine check interrupt is masked.
3
IDIM
Inbound doorbell interrupt mask
0 Inbound doorbell interrupt is allowed.
1 Inbound doorbell interrupt is masked.
2
—
1
IM1IM
Inbound message 1 interrupt mask
0 Inbound doorbell interrupt is allowed.
1 Inbound doorbell interrupt is masked.
0
IM0IM
Inbound message 0 interrupt mask
0 Inbound message 0 interrupt is allowed.
1 Inbound message 0 interrupt is masked.
9.12.3.4.7
Description
Reserved, should be cleared.
Reserved, should be cleared.
Messaging Unit Control Register (MUCR)
This register allows software to enable and setup the size of the inbound and outbound FIFOs. MUCR
should be accessed only from the 60x bus and only in agent mode. Accesses while in host mode or from
the PCI bus have undefined results.
31
16
Field
—
Reset
0000_0000_0000_0002
R/W
R/W
Addr
0x104E6
15
Field
Reset
6
5
—
1
CQS
0
CQE
0000_0000_0000_0000
R/W
R/W
Addr
0x104E4
Figure 9-79. Messaging Unit Control Register (MUCR)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-84
Freescale Semiconductor
PCI Bridge
Table 9-64 describes MUCR fields.
Table 9-64. MUCR Field Descriptions
Bits
Name
Access
31–6
—
R
5–1
CQS
RW
Circular queue size. CQS refers to each individual queue, not the total size of all four
queues together.
00001 4K entries (16 Kbytes)
00010 8K entries (32 Kbytes)
00100 16K entries (64 Kbytes)
01000 32K entries (128 Kbytes)
10000 64K entries (256 Kbytes)
All others reserved.
0
CQE
RW
Circular queue enable. When set will allow PCI masters to access the inbound and
outbound queue ports. Writes are ignored and reads will return 0xFFFF_FFFF when
this bit is cleared. Normally, this bit is set only if software has initialized all pointers and
configuration registers.
9.12.3.4.8
Description
Reserved, should be cleared.
Queue Base Address Register (QBAR)
This register specifies the beginning of the circular queue structure in local memory. The following QBAR
should be accessed only from the 60x bus and only in agent mode. Accesses while in host mode or from
the PCI bus have undefined results.
31
20
Field
QBA
Reset
19
16
—
0000_0000_0000_0000
R/W
R/W
Addr
0x104F2
15
0
Field
—
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x104F0
Figure 9-80. Queue Base Address Register (QBAR)
Table 9-65 describes QBAR fields.
Table 9-65. QBAR Field Descriptions
Bits
Name
Access
31–20
QBA
RW
19–0
—
R
Description
Queue base address. Base address of circular queue in local memory. It must be
aligned to a 1Mbyte boundary.
Reserved, should be cleared.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-85
PCI Bridge
9.13
DMA Controller
The PCI bridge’s DMA controller transfers blocks of data independent of the local core or PCI hosts. Data
movement occurs on the PCI and/or 60x bus. The PCI Bridge’s DMA module has four high-speed DMA
channels with an aggregate bandwidth conservatively estimated at 210 Mbytes per second, for 60x to PCI
transfer. The channels share 144 bytes of DMA-dedicated buffer space to facilitate the gathering and
sending of data. Both the local core and PCI masters can initiate a DMA transfer.
Features of the DMA controller include the following:
• 4 channels
• Concurrent execution across multiple channels with programmable bandwidth control
• All channels are accessible by local core and remote PCI masters.
• Unaligned transfer capability
• Data chaining and direct mode
• Interrupt on completed segment, chain, and error
• Supports all transfer combinations between 60x memory and PCI memory: 60x-to-60x,
PCI-to-PCI, 60x-to-PCI, and PCI-to-60x.
Figure 9-81 shows a block diagram of the DMA controller.
60x bus
DMA0
DMA1
DMA2
DMA3
Interface logic
I/O sequencer
PCI bus
Figure 9-81. DMA Controller Block Diagram
9.13.1
DMA Operation
The DMA controller operates in two modes—chaining and direct. In direct mode, the software is
responsible for initializing the source, destination and byte count registers. In chaining mode, the software
first must build a chain of descriptor segments in external memory, residing either on the 60x or PCI bus,
and then initialize the current descriptor address register to point to the first descriptor segment in the
chain. In both modes, setting the start bit in the DMA mode register begins the DMA transfer.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-86
Freescale Semiconductor
PCI Bridge
The DMA controller supports unaligned transfers for both the source and destination addresses. It gathers
data beginning at the source address and aligns the data accordingly before sending it to the destination
address. The DMA controller assumes that the source and destination addresses are valid PCI or 60x
memory addresses.
All 60x memory read operations are cache line reads (32 bytes); the DMA controller selects the
appropriate/valid data bytes within the cache line when loading its internal queue. Writing to 60x memory
depends on the alignment of the destination address and the size of the transfer. The DMA controller writes
a full cache line whenever possible. Misaligned destination addresses result in sub-transfers of less than a
cache line on the initial and final beats of the transfer; intermediate beats transfer full cache lines.
Configuring a DMA channel for a transfer size of less than 8 bytes in address hold mode (DAHE or SAHE
is set; refer to Section 9.13.1.6.1, “DMA Mode Registers 0–3 (DMAMRx)”) precludes cache line writes.
PCI memory read operations depend on the PRC (PCI read command) field in the mode register, the
alignment of the source address and the size of the transfer. The DMA controller attempts to read a full
cache line whenever possible. Writing to PCI memory depends on the alignment of the destination address
and the size of the transfer.
9.13.1.1
DMA Direct Mode
In direct mode, the DMA controller does not read a chain of descriptors from memory but instead uses the
current parameters in the DMA registers to start a DMA transfer. The DMA transfer finishes after all the
bytes specified in the byte count register have been transferred or an error condition has occurred. Below
are the initialization steps of a DMA transfer in direct mode.
• Poll the CB (channel busy) bit in the status register to make sure the DMA channel is idle (refer to
Section 9.13.1.6.2, “DMA Status Registers 0–3 (DMASRx)”).
• Initialize the source, destination and byte count register (refer to Section 9.13.1.6.5, “DMA
Destination Address Registers 0–3 (DMADARx),” and Section 9.13.1.6.6, “DMA Byte Count
Registers 0–3 (DMABCRx)”).
• Initialize the CTM (channel transfer mode) bit in the mode register (refer to Section 9.13.1.6.1,
“DMA Mode Registers 0–3 (DMAMRx)”) to indicate direct mode. Other control parameters in the
mode register can also be initialized here if necessary.
• First clear then set the CS (channel start) bit in the mode register to start the DMA transfer.
9.13.1.2
DMA Chaining Mode
In chaining mode, the DMA controller loads descriptors from memory prior to a DMA transfer. The DMA
controller begins the transfer according to the descriptor information loaded for each segment. Once the
current segment is finished, the DMA controller reads the next descriptor from memory and begins another
DMA transfer. The process is finished if the current descriptor is the last one in the chain or an error
condition has occurred. Below are the initialization steps of a DMA transfer in chaining mode.
• Build a chain of descriptor segments in memory. Refer to the Section 9.13.2, “DMA Segment
Descriptors,” for more information.
• Poll the CB (channel busy) bit in the status register to make sure the DMA channel is idle.
• Initialize the current descriptor address register to point to the first descriptor in the chain.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-87
PCI Bridge
•
•
Initialize the CTM (channel transfer mode) bit in the mode register to indicate chaining mode.
Other control parameters in the mode register can also be initialized here if necessary.
First clear then set the CS (channel start) bit in the mode register to start the DMA transfer.
9.13.1.3
DMA Coherency
The four DMA channels are allocated 4 cache lines (128 bytes) of buffer space in the I/O sequencer module
in addition to 16 bytes of local buffer space. Because no address snooping occurs in these internal queues,
data posted in these queues is not visible to the rest of the system while a DMA transfer is in progress. It
is the responsibility of application software to ensure the coherency of the region being transferred during
the DMA process.
Snooping of the core data cache is selectable during DMA transactions. A snoop bit is provided in the
current descriptor address register and the next descriptor address register which allows software to control
when the cache is snooped. These bits are described in Section 9.13.1.6.3, “DMA Current Descriptor
Address Registers 0–3 (DMACDARx),” and Section 9.13.1.6.7, “DMA Next Descriptor Address
Registers 0–3 (DMANDARx),” respectively.
9.13.1.4
Halt and Error Conditions
DMA transfers are halted either by clearing the CS (channel start) bit in the mode register or when
encountering an error condition. In both cases the application software can one of the following:
• Continue the DMA transfer
• Reconfigure the DMA for a new transfer
• Leave the channel in the halted state
When a DMA channel is halted, its programming model is completely accessible. If the DMA is halted
due to an error condition, the TE (transfer error) bit in the status register must be cleared before the transfer
can be resumed or a new transfer initiated. Note that the TE bit is not cleared automatically by hardware.
NOTE: DMA Operation After Bus Error
After any bus error which occurs in the MPC8280 (either 60x or PCI, not
necessarily due to DMA operation), the user must reset the system to avoid
DMA malfunction.
9.13.1.5
DMA Transfer Types
The DMA controller supports all transfers between 60x memory and PCI memory: 60x-to-60x,
PCI-to-PCI, 60x-to-PCI, and PCI-to-60x. All data is temporarily stored in a 144-byte queue prior to
transmission. There are four types of DMA transfers:
• PCI-memory-to-PCI-memory transfers—The DMA controller begins by reading data from PCI
memory space and storing it in the DMA queue. Once sufficient data is stored in the queue, the
DMA controller begins writing data from the queue to PCI memory space beginning at the
destination address. The process is repeated until there is no more data to transfer or an error
condition has occurred on the PCI bus.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-88
Freescale Semiconductor
PCI Bridge
•
•
•
PCI-memory-to-60x-memory transfers—The DMA controller initiates reads on the PCI bus and
stores the data in the DMA queue. Once sufficient data is stored in the queue, a 60x memory write
is initiated. The DMA controller stops the transfer either for an error condition on the PCI bus or
60x bus, or when no data is left to transfer. Reading from PCI memory and writing to 60x memory
can occur concurrently.
60x-memory-to-PCI-memory transfers—The DMA controller initially fetches data from 60x
memory into the DMA queue. As soon as the first data arrives into the queue, the DMA engine
initiates write transactions to PCI memory. The DMA controller stops the transfer either when
there is an error on the PCI bus or 60x bus, or there is no more data left to transfer. Reading from
60x memory and writing to PCI memory can occur concurrently.
60x-memory-to-60x-memory transfers—The DMA controller begins reading data from 60x
memory and storing it in the DMA queue. Once sufficient data is stored in the queue, the DMA
controller begins writing data to 60x memory space beginning at the destination address. The
process is repeated until there is no more data to transfer or an error condition has occurred while
accessing memory.
9.13.1.6
DMA Registers
Each DMA channel has a set of seven 32-bit registers (mode, status, current descriptor address, next
descriptor address, source address, destination address, and byte count) to support transactions. This
section describes the format of the DMA support registers.
DMA Mode Registers 0–3 (DMAMRx)
9.13.1.6.1
The mode register allows software to start the DMA transfer and to control various DMA transfer
characteristics.
31
24
Field
23
—
21
BWC
Reset
20
19
DM_SEN IRQS
18
17
—
DAHTS
0000_0000_0000_0000
R/W
R/W
Addr
0x10502 (DMAMR0); 0x10582 (DMAMR1); 0x10602 (DMAMR2); 0x10682 (DMAMR3)
15
Field
16
14
13
SAHTS
12
DAHE SAHE
Reset
11
10
PRC
9
8
—
7
6
EOTIE
4
—
3
2
TEM CTM
1
0
CC
CS
0000_0000_0000_0000
R/W
R/W
Addr
0x10500 (DMAMR0); 0x10580 (DMAMR1); 0x10600 (DMAMR2); 0x10680 (DMAMR3)
Figure 9-82. DMA Mode Registers 0–3 (DMAMRx)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-89
PCI Bridge
Table 9-66 describes DMAMRx fields.
Table 9-66. DMAMRx Field Descriptions
Bits
Name
31–24
—
23–21
BWC
Description
Reserved, should be cleared.
Bandwidth control. This field only applies when multiple channels are executing
transfers concurrently. The field determines how many cache lines a given Channel
is allowed to transfer after it is granted access to the IOS interface and before it
releases the interface to the next channel. This allows the user to prioritize DMA
Channels.
000 1 cache line
001 2 cache lines
010 4 cache lines
011 8 cache lines
100 16 cache lines
20
DM_SEN
Direct mode snoop enable. When set allows snooping during direct mode DMA
transactions.
19
IRQS
18
—
17–16
DAHTS
Destination address hold transfer size. Indicates the transfer size used for each
transaction when DAHE is enabled. The Byte Count Register must be in multiples of
the size, and the Destination Address Register must be aligned based on the size.
00 1 byte
01 2 bytes
10 4 bytes
11 8 bytes
15–14
SAHTS
Source address hold transfer size. Indicates the transfer size used for each
transaction when SAHE is enabled. The Byte Count Register must be in multiples of
the size, and the Source Address Register must be aligned based on the size.
00 1 byte
01 2 bytes
10 4 bytes
11 -8 bytes
13
DAHE
Destination address hold enable. When set will allow the DMA controller to hold the
destination address constant for every transfer. The size used for transfer is
indicated by DAHTS. Note that hardware supports only aligned transfers for this
feature.
12
SAHE
Source address hold enable. When set will allow the DMA controller to hold the
source address constant for every transfer. The size used for the transfer is indicated
by SAHTS. Note that hardware supports only aligned transfers for this feature.
11–10
PRC
PCI read command. Indicates the types of PCI read command to use.
00 PCI read
01 PCI read line
10 PCI read multiple
11 Reserved
9–8
—
Interrupt steer. When set routes all DMA interrupts to PCI bus through INTA. When
clear routes all DMA interrupts to local core.
Reserved, should be cleared.
Reserved, should be cleared.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-90
Freescale Semiconductor
PCI Bridge
Table 9-66. DMAMR x Field Descriptions (continued)
Bits
Name
Description
7
EOTIE
End-of-transfer interrupt enable. When set will generate an interrupt at the
completion of a DMA transfer. No EOT interrupt is generated if this bit is cleared. End
of transfer is defined as the end of a direct mode transfer or in chaining mode, as the
end of the transfer of the last segment of a chain.
6–4
—
3
TEM
Transfer error mask. This bit determines the DMA response in the event of a transfer
error. If this bit is set, the DMA will complete the transfer regardless of whether a
transfer error occurs (the TE bit is not set). If this bit is clear, the DMA will halt when
a transfer error occurs (TE bit is set).
2
CTM
Channel transfer mode
0 Chaining mode. See Section 9.13.1.2, “DMA Chaining Mode.”
1 Direct mode. See Section 9.13.1.1, “DMA Direct Mode.”
1
CC
Channel continue. When this bit is set, the DMA transfer will restart the transferring
process starting at the Current Descriptor Address. This bit applies only to chaining
mode and is cleared by hardware after every descriptor read.
0
CS
Channel start. A 0-to-1 transition occurring on this bit when the channel is not busy
(SR[CB] bit is 0) will start the DMA process. If the channel is busy and a 0 to 1
transition occurs, then DMA channel will restart from a previous halt condition. A
1-to-0 transition when the channel is busy (CB bit is 1) will halt the DMA process.
Nothing happens if the channel is not busy and a 1 to 0 transition occurs.
Reserved, should be cleared.
DMA Status Registers 0–3 (DMASRx)
9.13.1.6.2
The status register reports various DMA conditions during and after the DMA transfer. Writing a 1 to a
specific set bit clears the bit.
31
16
Field
—
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x10506(DMASR0); 0x10586 (DMASR1); 0x10606 (DMASR2); 0x10686 (DMASR3)
15
Field
Reset
8
—
7
6
TE
3
—
2
CB
1
0
EOSI EOCDI
0000_0000_0000_0000
R/W
R/W
Addr
0x10504 (DMASR0); 0x10584(DMASR1); 0x10604 (DMASR2); 0x10684 (DMASR3)
Figure 9-83. DMA Status Registers 0–3 (DMASRx)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-91
PCI Bridge
Table 9-67 describes DMASRx fields.
Table 9-67. DMASRx Field Descriptions
Bits
Name
Access
Description
31–8
—
RW
7
TE
Read/
Write 1
to clear
6–3
—
R
2
CB
Read
Only
Channel busy. When set indicates that a DMA transfer is currently in progress. This
bit will be cleared as a result of any of the three following conditions: (1) an error, (2)
a halt, or (3) completion of the DMA transfer.
1
EOSI
Read/
Write 1
to clear
End-of-segment interrupt. After transferring a segment of data, if the EOSIE bit in the
current descriptor address register is set, then this bit will be set and an interrupt is
generated. Otherwise, no interrupt is generated.
0
EOCDI
Read/
Write 1
to clear
End-of-chain/direct Interrupt. When the last DMA transfer is finished, either in
chaining or direct mode, if DMAMR[EOTIE] is set, this bit will be set and an interrupt
is generated. Otherwise, no interrupt is generated.
Reserved, should be cleared.
Transfer error. This bit is set when there is an error condition during the DMA transfer
and the TEM bit is cleared.
Reserved, should be cleared.
DMA Current Descriptor Address Registers 0–3 (DMACDARx)
9.13.1.6.3
The current descriptor address register contains the address of the current segment descriptor being
transferred. In chaining mode, software must initialize this register to point to the first descriptor in the
chain. After processing the first descriptor, the DMA controller moves the contents of the next descriptor
address register into DMACDAR, loads the next descriptor into DMANDAR, and executes the current
transfer. This process continues until encountering a descriptor whose EOTD (end-of-transfer descriptor)
bit is set, which will be the last descriptor to be executed.
31
16
Field
CDA
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x1050A(DMACDR0); 0x1058A (DMACDR1); 0x1060A (DMACDR2); 0x1068A (DMACDR3)
15
Field
Reset
5
CDA
4
3
2
SNEN EOSIE
0
—
0000_0000_0000_0000
R/W
R/W
Addr
0x10508 (DMACDR0); 0x10588 (DMACDR1); 0x10608 (DMACDR2); 0x10688 (DMACDR3)
Figure 9-84. DMA Current Descriptor Address Registers 0–3 (DMACDARx)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-92
Freescale Semiconductor
PCI Bridge
Table 9-68 describes DMACDARx fields.
Table 9-68. DMACDAR x Field Descriptions
Bits
Name
Description
31–5
CDA
4
SNEN
Snoop enable. When set will allow snooping on DMA transactions.
3
EOSIE
End-of-segment interrupt enable. When set will generate an interrupt if the current DMA
transfer for the current descriptor is finished.
2–0
—
Current descriptor address. Contains the current descriptor address of the segment
descriptor in memory. It must be aligned on an 8-word boundary.
Reserved, should be cleared.
DMA Source Address Registers 0–3 (DMASARx)
9.13.1.6.4
The source address register, shown in Figure 9-85, indicates the address where the DMA controller will be
reading data from. This address can be in either PCI memory or 60x memory. The software has to ensure
that this is a valid memory address.
The choice between PCI or 60x is done according to the following rule: If the address hits one of the PCI
outbound windows, then the source data is read from the PCI memory. Otherwise, it is read from the 60x
memory. Refer to Figure 9-13.
31
16
Field
SA
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x10512(DMASAR0); 0x10592 (DMASAR1); 0x10612 (DMASAR2); 0x10692 (DMASAR3)
15
0
Field
SA
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x10510 (DMASAR0); 0x10590 (DMASAR1); 0x10610 (DMASAR2); 0x10690 (DMASAR3)
Figure 9-85. DMA Source Address Registers 0–3 (DMASARx)
Table 9-69 describes DMASARx fields.
Table 9-69. DMASARx Field Descriptions
Bit
Name
Description
31–0
SA
Source address of DMA transfer. The content is updated after every DMA read operation.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-93
PCI Bridge
DMA Destination Address Registers 0–3 (DMADARx)
9.13.1.6.5
The destination address register, shown in Figure 9-86, indicates the address where the DMA controller
will be writing data to. This address can be in either PCI memory or 60x memory. The software has to
ensure that this is a valid memory address.
The choice between PCI or 60x is done according to the following rule: If the address hits one of the PCI
outbound windows, then the destination data is written to the PCI memory. Otherwise, it is written to the
60x memory. Refer to Figure 9-13.
31
16
Field
DA
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x1051A (DMAADAR0); 0x1059A (DMAADAR1); 0x1061A (DMAADAR2); 0x1069A (DMAADAR3)
15
0
Field
DA
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x10518 (DMAADAR0); 0x10598 (DMAADAR1); 0x10618 (DMAADAR2); 0x10698 (DMAADAR3)
Figure 9-86. DMA Destination Address Registers 0–3 (DMADARx)
Table 9-70 describes DMADARx fields.
Table 9-70. DMADARx Field Descriptions
Bit
Name
31–0
DA
9.13.1.6.6
Description
Destination address. The content is updated after every DMA write operation.
DMA Byte Count Registers 0–3 (DMABCRx)
This register contains the number of bytes per transfer (maximum transfer size is 64 Mbytes).
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-94
Freescale Semiconductor
PCI Bridge
31
26
Field
25
16
—
BC
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x10522 (DMABCR0); 0x105A2(DMABCR1); 0x10622 (DMABCR2); 0x106A2 (DMABCR3)
15
0
Field
BC
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x10520 (DMABCR0); 0x105A0 (DMABCR1); 0x10620 (DMABCR2); 0x106A0 (DMABCR3)
Figure 9-87. DMA Byte Count Registers 0–3 (DMABCRx)
Table 9-71 describes DMABCRx fields.
Table 9-71. DMABCRx Field Descriptions
Bit
Name
Description
31–26
—
Reserved, should be cleared.
25–0
BC
Byte count. Contains the number of bytes to transfer. The value in this register is
decremented after each DMA read operation.
DMA Next Descriptor Address Registers 0–3 (DMANDARx)
9.13.1.6.7
The next descriptor address register (NDAR) contains the address for the next segment descriptor in the
chain. In chaining mode, this register is loaded from the “next descriptor” field of the descriptor that the
current descriptor register is pointing to. Refer to Figure 9-89.
31
16
Field
NDA
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x10526 (DMANDAR0); 0x105A6 (DMANDAR1); 0x10626 (DMANDAR2); 0x106A6 (DMANDAR3)
15
5
Field
NDA
Reset
4
3
2
NDSNE NDEOSIE
N
1
—
0
EOTD
0000_0000_0000_0000
R/W
R/W
Addr
0x10524 (DMANDAR0); 0x105A4 (DMANDAR1); 0x10624 (DMANDAR2); 0x106A4 (DMANDAR3)
Figure 9-88. DMA Next Descriptor Address Registers 0–3 (DMANDARx)
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-95
PCI Bridge
Table 9-72 describes DMANDARx fields.
Table 9-72. DMANDARx Field Descriptions
Bit
Name
Description
31–5
NDA
Next descriptor address. Contains the next descriptor address of the segment descriptor
in memory. It must be aligned on an 8-word (32-byte) boundary.
4
NDSNEN
Next descriptor snoop enable. When set will allow snooping on DMA transactions.
3
NDEOSIE
Next descriptor end-of-segment interrupt enable. When set will generate an interrupt at
the end of this DMA transfer.
2–1
—
0
EOTD
9.13.2
Reserved, should be cleared.
End-of-transfer descriptor. When set indicates that this descriptor is the last one to be
executed.
DMA Segment Descriptors
DMA segment descriptors contain the source and destination addresses of the data segment, the segment
byte count, and a link to the next descriptor. Segment descriptors are built on cache-line (32-byte)
boundaries in either 60x or PCI memory and are linked together into chains using the
next-descriptor-address field.
Table 9-73. DMA Segment Descriptor Fields
Descriptor Field
Description
Source address
Contains the source address of the DMA transfer. After the DMA controller reads the
descriptor from memory, this field will be loaded into the source address register. For the bit
definition, refer to Section 9.13.1.6.4, “DMA Source Address Registers 0–3 (DMASARx).”
Destination address
Contains the destination address of the DMA transfer. After the DMA controller reads the
descriptor from memory, this field will be loaded into the destination address register. For the
bit definition, refer to Section 9.13.1.6.5, “DMA Destination Address Registers 0–3
(DMADARx).”
Next descriptor address Points to the next descriptor in memory. After the DMA controller reads the descriptor from
memory, this field will be loaded into the next descriptor address register. For the bit definition,
refer to Section 9.13.1.6.7, “DMA Next Descriptor Address Registers 0–3 (DMANDARx).”
Byte count
Contains the number of bytes to transfer. After the DMA controller reads the descriptor from
memory, this field will be loaded into the byte count register. For the bit definition, refer to
Section 9.13.1.6.6, “DMA Byte Count Registers 0–3 (DMABCRx).”
Application software initializes the current descriptor address register (DMACDARx) to point to the first
descriptor in the chain. For each descriptor in the chain, the DMA controller starts a new DMA transfer
with the control parameters specified by the descriptor. The DMA controller traverses the descriptor chain
until reaching the last descriptor (with its EOTD bit set).
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-96
Freescale Semiconductor
PCI Bridge
Current descriptor address register
31
0
Next descriptor address register
31
0
Local memory or PCI memory
Offset
0x00
0x04
0x08
0x0C
0x10
0x14
0x18
0x1C
Source address
Reserved
Destination address
Reserved
Next descriptor
Reserved
Byte count
Reserved
31
Offset
0x00
0x04
0x08
0x0C
0x10
0x14
0x18
0x1C
Descriptor 0
0
Source address
Reserved
Destination address
Reserved
Next descriptor
Reserved
Byte count
Reserved
31
Offset
0x00
0x04
0x08
0x0C
0x10
0x14
0x18
0x1C
Descriptor 1
0
Source address
Reserved
Destination address
Reserved
Next descriptor
Reserved
Byte count
Reserved
31
Descriptor N
(last)
EOTD=1
0
Figure 9-89. DMA Chain of Segment Descriptors
9.13.2.1
Descriptor in Big-Endian Mode
In big endian mode, the descriptor in 60x memory should be programmed such that data appears in
ascending significant-byte order. If segment descriptors are written to memory located in the 60x bus, they
should be treated like they are translated from big endian to little endian mode.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-97
PCI Bridge
Example: Big Endian mode descriptor’s data structure. Note that the descriptor structure must be aligned
on an 8-word boundary.
struct {
double a;
/* 0x1122334455667788 double word
double b;
/* 0x55667788aabbccdd double word
double c;
/* 0x8765432101234567 double word */
double d;
/* 0x0123456789abcdef double word */
} Descriptor;
Results: Source Address = 0x44332211 <MSB..LSB>
Destination Address = 0x88776655 <MSB..LSB>
Next Descriptor Address = 0x21436587 <MSB..LSB>
Byte Count = 0x67452301 <MSB..LSB>
9.13.2.2
*/
*/
Descriptor in Little-Endian Mode
In little endian mode, the descriptor in PCI memory should be programmed such that data appears in
descending significant byte order. If segment descriptors are written to memory located in the PCI bus,
they are obeying the rules for little endian mode.
Example: Little Endian mode descriptor’s data structure. Note that the descriptor structure must be
aligned on an 8-word boundary.
struct {
double a;
/* 0x8877665544332211 double word
double b;
/* 0x1122334488776655 double word
double c;
/* 0x7654321012345678 double word */
double d;
/* 0x0123456776543210 double word */
} Descriptor;
Results: Source Address = 0x44332211 <MSB..LSB>
Destination Address = 0x88776655 <MSB..LSB>
Next Descriptor Address = 0x12345678 <MSB..LSB>
Byte Count = 0x76543210 <MSB..LSB>
9.14
*/
*/
Error Handling
The PCI bridge provides error detection and reporting. This section describes how the PCI bridge handles
different error (or interrupt) conditions.
Errors detected by the PCI bridge are reported by asserting internal error signals for each detected error.
The system error (SERR) and parity error (PERR) signals are used to report errors on the PCI bus.
The PCI command and status registers and the error handling registers enable or disable the reporting and
detection of specific errors. There are six registers which define capture and control functionality under
error conditions. Refer to section 9.11.1.9 through section 9.11.1.14.
The PCI bridge detects illegal transfer sizes to its configuration registers, PCI master-abort cycles, PCI
received target-abort errors, PCI parity errors, and overflow/underflow errors in the message unit.The PCI
bridge latches the address and type of transaction that caused the error in the error registers to assist
diagnostic and error handling software.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-98
Freescale Semiconductor
PCI Bridge
9.14.1
Interrupt and Error Signals
Although Section 9.11, “Configuration Registers,” contains the definitions for the interrupt and error
signals, this section describes the interactions between system components when an interrupt or error
signal is asserted.
9.14.1.1
PCI Bus Error Signals
The PCI bridge uses two error signals to interact with the PCI bus, SERR and PERR.
9.14.1.1.1
System Error (SERR)
The SERR signal is used to report PCI address parity errors. It is driven for a single PCI clock cycle by the
agent that is reporting the error. The agent responsible for driving AD[31–0] on a given PCI bus phase is
responsible for driving even parity one PCI clock later on the PAR signal. (That is, the number of 1’s on
AD[31–0], PCI_C/BE[3–0], and PAR equals an even number.) The target agent is not allowed to terminate
with retry or disconnect if SERR is activated due to an address parity error.
Bits 8 and 6 of the PCI command register controls whether the PCI bridge asserts SERR upon detecting
one of the error conditions.
9.14.1.1.2
Parity Error (PERR)
The PERR signal is used to report PCI data parity errors during all PCI transactions, except for a PCI
special-cycle command. The agent responsible for driving AD[31–0] on a given PCI bus phase is
responsible for driving even parity one PCI clock later on the PAR signal. That is, the number of 1’s on
AD[31–0], PCI_C/BE[3–0], and PAR equals an even number.
The PERR signal must be asserted by the agent receiving data two PCI clocks following the data phase for
which a data parity error was detected. Only the master may report a read data parity error and only the
selected target may report a write data parity error.
Bit 6 of the PCI command register controls whether the PCI bridge ignores PERR.
9.14.1.1.3
Error Reporting
The error signals generated by the PCI bridge indicate which specific error has been detected.
The error control and address registers and the data capture registers are used to provide additional
information about the detected error. When an error is detected, the associated information is latched inside
these registers until all the associated error flags are cleared. Subsequent errors will set the appropriate
error flags in the error detection registers, but will not latch additional information.
9.14.1.2
Illegal Register Access Error
An illegal register access error occurs when an access to a configuration register is not specified to be 1
beat. When this occurs, ESR[IRA] is set (refer to Section 9.11.1.9, “Error Status Register (ESR)”). If a read
transaction causes the illegal access error the PCI bridge returns 0xFF (all 1s) and a write transaction with
an illegal register access error will be dropped.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-99
PCI Bridge
9.14.1.3
PCI Interface
The PCI bridge supports the error detection and reporting mechanism as specified in the PCI Local Bus
Specification, Revision 2.2. The PCI bridge detects master and target abort errors, address parity errors,
received SERR, and master and target PERR errors. In these cases, the appropriate bit is set in the ESR,
and the address, data and control information about the transaction is loaded in the PCI error address
capture register (PCI_EACR), the PCI data capture register (PCI_EDCR) and the PCI error control capture
register.
9.14.1.3.1
Address Parity Error
If the PCI bridge is acting as a PCI master and the target detects and reports (by asserting SERR) a PCI
address parity error, the PCI bridge sets bit 5 of the ESR and sets the detected parity error bit (bit 15) in
the PCI status register. This setting of bit 15 is independent of the settings in the PCI command register.
If the PCI bridge is acting as a PCI target and detects a PCI address parity error, the PCI interface of the
PCI bridge sets the status bit in the PCI status register (bit 15) and bit 0 of the ESR. If bits 6 and 8 of the
PCI command register are set, the PCI bridge reports the address parity error by asserting SERR to the
master (two clocks after the address phase) and sets bit 14 of the PCI status register.
9.14.1.3.2
Data Parity Error
If the PCI bridge is acting as a PCI master and a write data parity error is signaled by the target asserting
PERR, the PCI bridge sets bit 8 of the PCI status register if the parity error response bit (bit 6) in the PCI
command Register is set. The PCI bridge sets bit 7 of the error status register (refer to Section 9.11.1.9,
“Error Status Register (ESR)”), regardless of the configuration of the PCI command register.
If the PCI bridge is acting as a PCI master and a read data parity error occurs, the PCI bridge sets bit 8 of
the PCI status register if the parity error response bit (bit 6) in the PCI command register is set. The PCI
bridge sets bit 2 of the error status register. If the PCI command register of the PCI bridge is programmed
to respond to parity errors (bit 6 of the PCI command register is set) the PCI bridge reports the error to the
PCI target by asserting PERR and tries to complete the command if possible. The PCI bridge also sets bit
15 of the PCI status register regardless of the value of the parity error response bit (bit 6) in the PCI
command register.
If the PCI bridge is acting as a PCI target when the write data parity error occurs, the PCI bridge sets bit
15 of the PCI status register and bit 1 of the error status register (ESR). The setting of these bits is
independent of the settings in the PCI command register. If bit 6 of the PCI command Register is set, the
PCI bridge asserts PERR. When the data has all been transferred, the PCI bridge completes the operation
but ignores the data.
If the PCI bridge is acting as a PCI target when the master asserts PERR, the PCI bridge sets bit 6 of ESR
(refer to Section 9.11.1.9, “Error Status Register (ESR)”), regardless of the configuration of the PCI
command register.
9.14.1.3.3
Master-Abort Transaction Termination
If the PCI bridge, acting as a master, initiates a PCI bus transaction (excluding special-cycle transactions)
but there is no response from any PCI agent (DEVSEL has not been asserted within five PCI bus clocks
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-100
Freescale Semiconductor
PCI Bridge
from the start of the address phase), the PCI bridge terminates the transaction with a master-abort and sets
the master-abort flag (bit 13) in the PCI status register and bit 3 in the ESR.
In the case of no response for a PCI read configuration transaction, the PCI bridge terminates the
transaction with a master-abort, but will return data of all ones and will not assert a machine check. This
kind of termination enables the host CPU to perform a PCI device scan without having to know in advance
if a particular PCI slot is populated or empty. The software still needs to mask the PCI_NO_RSP bit in the
error mask register (refer to Section 9.11.1.10, “Error Mask Register (EMR)”). Any other type of
transaction that is terminated with a master-abort results in a machine check interrupt.
9.14.1.3.4
Target-Abort Error
If a PCI transaction initiated by the PCI bridge is terminated by target-abort, the PCI bridge sets the
received target-abort flag (bit 12) of the PCI status register and bit 4 of the error status register (refer to
Section 9.11.1.9, “Error Status Register (ESR)”). Note that data transferred in a target-aborted transaction
may be corrupt.
9.14.1.3.5
NMI
This signal is captured in bit 11 of the ESR (refer to Section 9.11.1.9, “Error Status Register (ESR)”). It
indicates that an error has occurred on the 60x bus in a transaction that was originally initiated by the PCI
bridge.
9.14.1.4
Embedded Utilities
Embedded utilities errors are errors detected in the I2O interface. Embedded utilities errors are limited to
queue overflows in the I2O outbound free queue and the inbound post queue.
9.14.1.4.1
Outbound Free Queue Overflow
If the PCI bridge detects an I2O outbound free queue overflow, it sets bit 8 of the error status register (refer
to Section 9.11.1.9, “Error Status Register (ESR)”) and freezes all I2O state information.
9.14.1.4.2
Inbound Post Queue Overflow
If the PCI bridge detects an I2O inbound post queue overflow, it sets bit 9 of the error status register (refer
to Section 9.11.1.9, “Error Status Register (ESR)”) and freezes all I2O state information.
9.14.1.4.3
Inbound DoorBell Machine Check
If an external PCI master writes the inbound doorbell register such that the most significant bit is set, then
bit 12 of ESR (refer to Section 9.11.1.9, “Error Status Register (ESR)”) is set and a machine check is
asserted to the local processor.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
9-101
PCI Bridge
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
9-102
Freescale Semiconductor
Chapter 10
Clocks and Power Control
The MPC8280’s clocking architecture includes two PLLs—the main PLL and the core PLL. The main
PLL, together with the dividers, provides the internal 60x bus clock and internal clocks for all blocks in
the chip except core blocks. The core PLL provides the internal core clocks.
The MPC8280’s clocking is a configurable system supporting three clock configuration modes. The clock
configuration mode is set during the power on reset.
CLKIN is the primary timing reference for the MPC8280. The frequency of CLKIN equals 60x and local
bus frequencies. The main PLL multiplies the frequency of the input clock to the final CPM frequency.
Refer to Section 10.6, “Clock Configuration Modes.”
10.1
MPC8280 Clock Block Diagram
The MPC8280 clocking system, shown in Figure 10-1, is designed around two PLLs—the main PLL and
the core PLL. The main PLL receives CLKIN as its input clock and multiplies it to provide MAIN_CLK,
which is twice the CPM clock, to the clock block dividers. The dividers shown in Figure 10-1 generate all
MPC8280 internal clocks by synchronously dividing MAIN_CLK. These clocks are then output from the
clock block to the entire MPC8280.
10.1.1
Main PLL
The main PLL performs frequency multiplication and skew elimination. It allows the CPM to operate at a
high internal clock frequency while using a low-frequency clock input. This has two immediate benefits:
• A lower clock input frequency reduces overall electromagnetic interference generated by the
system
• Oscillating at different frequencies eliminates the need for another oscillator
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
10-1
Clocks and Power Control
10.1.2
Core PLL
The core PLL has the same advantages as the main PLL; it performs frequency multiplication and skew
elimination for the core blocks. The core PLL input clock is synchronous with the 60x bus clock. Its
configuration word, CORE_PLL_CFG[0-4], is determined by the MPC8280 clock configuration mode
setting. According to the setting, the core PLL multiplies the internal bus clock and synchronously
provides the core clocks.
10.1.3
Skew Elimination
The PLL can tighten synchronous timings by eliminating skew between phases of the internal clock and
the external clock entering the chip (CLKIN). Skew elimination is always active when the PLL is enabled.
Disabling the PLL (PLL bypass) can greatly increase clock skew.
10.1.4
Dividers
The PLL output clock, MAIN_CLK, is twice the CPM clock. MAIN_CLK applies to general-purpose
dividers. Each MPC8280 internal clock is generated by a dedicated divisor which is a programmable
number between 1 and 16. Dividers are determined by the clock configuration modes that are selected by
seven bits during the power-up reset—three hardware configuration pins (MODCK[1–3]) and four bits
from hardware configuration word[28–31] (MODCK_H). For complete lists of these dividers, refer to the
MPC8280 PowerQUICC II Family Hardware Specifications (order number: MPC8280EC). Note that all
dividers’ output clocks have identical skew in relation to the input clock because the delay through the
dividers for all clocks is identical independent of how its dividers have been programmed.
10.1.5
Internal Clock Signals
The internal logic of the MPC8280 generates the next internal clock lines:
• CPM general system clocks (CPM_CLK)
• 60x bus and local bus (BUS_CLK). Identical to CLKIN.
• SCC clocks (SCC_CLK)
• Baud-rate generator clock (BRG_CLK)
• PCI clock (PCI_CLK)
• DLL clocks
The PLL synchronizes these clock signals to each other.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
10-2
Freescale Semiconductor
Clocks and Power Control
Main PLL for CPM Clocks
CPM PLL
CLKIN1
X (SCMR[PLLMF]
+ 1)
MAIN_CLK (= 2 X CPM_CLK)
General-purpose divider
÷ 2
CPM_CLK
General-purpose divider
÷ (SCMR[BUSDF] + 1)
BUS_CLK2
General-purpose divider
÷ 4
SCC_CLK
General-purpose divider
÷ 22(SCCR[DFBRG] + 1)
BRG_CLK
General-purpose divider
÷ (SCCR[PCIDF] + 1)
PCI_CLK 1
CORE PLL
CORE_CLK
Core
BUS_CLK
SCMR[CORECNF]3
Notes:
1 In PCI agent mode, CLKIN = PCI_CLK. Refer to Section 10.1.6, “PCI Bridge as an Agent Operating from the
PCI System Clock.”
2
BUS_CLK = CLKIN.
3 The core PLL multiplication is set through SCMR[CORECNF] as described in Table 10-3.
4
SCMR is a read-only register. Its value is determined during power-on reset (PORESET). Refer to
Section 10.5, “System Clock Mode Register (SCMR).”
Figure 10-1. MPC8280 System Clock Architecture
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
10-3
Clocks and Power Control
10.1.6
PCI Bridge as an Agent Operating from the PCI System Clock
If the MPC8280 is connected to a system which generates the PCI clock, the PCI clock should be fed to
the CLKIN1 pin. The PCI clock is internally multiplied by the PLL to generate the chip’s internal high
speed clock. This clock is used to generate the 60x bus clock. The 60x bus clock is then driven by a DLL
circuit to the DLLOUT pin, which has a feedback path from the board to the CLKIN2 pin. This feedback
clock signal is used by the DLL logic to minimize clock skew between the internal and external clocks.
NOTE
All PCI timings are measured relative to CLKIN1; all 60x bus timings are
measured relative to CLKIN2.
CPM_CLK
MPC8280
PCI Interface
PCI_CLK
%
Dividers
%
BUS_CLK
dllout
PCI Circuit
60x Circuit
PLL
DLL
BUS_CLK
clkin2
Bus Clock
clkin1
PCI Clock
Figure 10-2. PCI Bridge as an Agent, Operating from the PCI System Clock
10.1.7
PCI Bridge as a Host Generating the PCI System Clock
In a system where the MPC8280 is the host that generates the PCI clock, the 60x bus clock should be
driven to the CLKIN1 pin. The 60x bus clock is internally multiplied by the PLL to generate the CPM high
speed clock and then internally divided to generate the PCI bus clock. The PCI bus clock is then driven by
the DLL circuit to the DLLOUT pin, which has a feedback path from the board to the CLKIN2 pin. This
feedback controls clock skew by ensuring the same internal and external clock timing.
NOTE
All PCI timings are measured relative to CLKIN2, and all 60x bus timings
are measured relative to CLKIN1.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
10-4
Freescale Semiconductor
Clocks and Power Control
CPM_CLK
MPC8280
PCI Interface
PCI_CLK
%
Dividers
%
BUS_CLK
dllout
PCI Circuit
PLL
DLL
60x Circuit
PCI_CLK
clkin2
clkin1
60x Bus Clock
PCI Clock
Figure 10-3. PCI Bridge as a Host, Generating the PCI System Clock
10.2
External Clock Inputs
The input clock source to the PLL is an external clock oscillator at the bus frequency. The PLL skew
elimination between the CLOCKIN pin and the internal bus clock is guaranteed.
10.3
PLL Pins
Table 10-1 shows the dedicated PLL pins.
Table 10-1. Dedicated PLL Pins
Signal
Description
VCCSYN1 Drain Voltage—Analog VDD dedicated to core analog PLL circuits. To ensure core clock stability, filter
the power to the VCCSYN1 input with a circuit similar to the one in “PLL Filtering Circuit” Figure. To filter
as much noise as possible, place the circuit as close as possible to VCCSYN1. The 0.1-µF capacitor
should be closest to VCCSYN1, followed by the 10-µF capacitor, and finally the 10-Ω resistor to Vdd.
These traces should be kept short and direct.
VCCSYN
Drain Voltage—Analog VDD dedicated to analog main PLL circuits. To ensure internal clock stability,
filter the power to the VCCSYN input with a circuit similar to the one in “PLL Filtering Circuit” Figure. To
filter as much noise as possible, place the circuit should as close as possible to VCCSYN. The 0.1-µF
capacitor should be closest to VCCSYN, followed by the 10-µF capacitor, and finally the 10-Ω resistor to
Vdd. These traces should be kept short and direct.
VDD
VCCSYN
10ohm
10uF
0.1uF
Figure 10-4. PLL Filtering Circuit
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
10-5
Clocks and Power Control
10.4
System Clock Control Register (SCCR)
The system clock control register (SCCR), shown in Figure 10-5, is memory-mapped into the MPC8280’s
internal space.
0
22
Field
—
Reset
0
23
24
25
PCI_MODE PCI_MODCK
28
PCIDF
Refer to Table 10-2
R/W
R/W
Addr
29
30
31
CLPD
DFBRG
0
01
R
R/W
0x10C80
Figure 10-5. System Clock Control Register (SCCR)
Table 10-2 SCCR Field Descriptions describes SCCR fields.
Table 10-2. SCCR Field Descriptions
Defaults
Bits
Name
Description
POR
Hard Reset
0–22
—
0
Unaffected Reserved
23
PCI_MODE
PCI_Mode
Unaffected PCI Mode
0 Disabled
1 Enabled
Reflects the inverted value of the PCI_Mode pin.
24
PCI_MODC
K
PCI_MODC
K
Unaffected Reflects the value of the PCI_MODCK pin.
25–28
PCIDF
Config pins
Unaffected PCI division factor.
29
CLPD
0
Unaffected CPM low power disable.
0 Default. CPM does not enter low power mode when the core
enters low power mode.
1 CPM and SIU enter low power mode when the core does. This
may be useful for debug tools that use the assertion of QREQ
as an indication of breakpoint in the core.
30–31
DFBRG
01
Unaffected Division factor of BRG_CLK. Determines BRG_CLK frequency.
Changing the value does not result in a loss of lock condition.
BRG_CLK is divided from the PLL output clock (defined as
“MAIN_CLK”), which is 2x the CPM clock. Refer to Figure 10-1.
The decimal equivalent of the binary value of SCCR[30–31]
determines the overall BRG_CLK dividers, as shown in
Figure 10-1. MAIN-CLK is divided by 22(DFBRG + 1).
00 Decimal value of 0; MAIN_CLK divided by 4.
01 Decimal value of 1; MAIN_CLK divided by 16 (normal
operation).
10 Decimal value of 2; MAIN_CLK divided by 64.
11 Decimal value of 3; MAIN_CLK divided by 256.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
10-6
Freescale Semiconductor
Clocks and Power Control
Note: At both Agent and Host PCI modes, when PCI_MODCK = 0, the ratio of CPM_CLK/PCI_CLK should be calculated from
PCIDF as follows:
CPM_CLK / PCI_CLK = (PCIDF + 1) / 2.
At both Agent and Host PCI modes, when PCI_MODCK = 1, the ratio of CPM_CLK/PCI_CLK should be calculated from
PCIDF as follows:
PCIDF = 3 > CPM_CLK / PCI_CLK = 4
PCIDF = 5 > CPM_CLK / PCI_CLK = 6
PCIDF = 7 > CPM_CLK / PCI_CLK = 8
PCIDF = 9 > CPM_CLK / PCI_CLK = 5
PCIDF = B > CPM_CLK / PCI_CLK = 6
10.5
System Clock Mode Register (SCMR)
The PLL, low power, and reset control register (SCMR), shown in Figure 10-6, hold the parameters
necessary for determining the output clock frequencies. To understand how the interaction of these values,
refer to Section 10.1, “MPC8280 Clock Block Diagram.”
0
Field PLLBP
Reset
—
2
3
7
—
8
CORECNF
11
12
BUSDF
00
15
CPMDF
Refer to Table 10-3
R/W
R
Addr
0x10C88
16
27
28
31
Field
—
PLLMF
Reset
0000_0000_0000
Refer to Table 10-3
R/W
R
Addr
0x10C8A
Figure 10-6. System Clock Mode Register (SCMR)
Table 10-3 describes SCMR fields.
Table 10-3. SCMR Field Descriptions
Defaults
Bits
Name
Description
PORESET Hard Reset
0
PLLBP
Config pin1
1–2
—
—
3–7
CORECNF
Config pins
Unaffected Core PLL configuration. Refer to Table 10-4 to see how these bits
translate to the actual core PLL multiplication mode.
8–11
BUSDF
Config pins
Unaffected 60x bus division factor.
12–15
CPMDF
Config pins
Unaffected CPM division factor. This value is always 1.
Unaffected Reset configuration for PLL bypass.
0 Normal operation
1 Bypass CPM PLL
—
Reserved
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
10-7
Clocks and Power Control
Table 10-3. SCMR Field Descriptions (continued)
Defaults
Bits
Name
Description
PORESET Hard Reset
16–27
—
—
28–31
PLLMF
Config pins
1
2
—
Reserved
Unaffected PLL multiplication factor. PLLMF controls the value of the divider in
the PLL feedback loop.
Note: The definition of PLLMF depends on the clock mode2:
• Local bus and PCI host: PLLMF = 2(CPM_CLK/CLKIN) – 1
• PCI agent: PLLMF = 2(CPM_CLK/PCI_CLK) – 1
Refer to Sections 10.1.6 and 10.1.7 for more details.
MODCK[1-3] and MODCK_H. Refer to Section 10.1.4, “Dividers.”
(CPM_CLK/CLKIN) is defined as the CPM Multiplication Factor in the MPC8280 Family Hardware Specifications.
(CPM_CLK/PCI_CLK) is defined as the CPM Multiplication Factor in the MPC8280 Family Hardware Specifications.
Note: At PCI Agent mode, when PCI_MODCK = 0, the ratio of CPM_CLK/PCI_CLK should be calculated from PLLMF as follows:
CPM_CLK / PCI_CLK = (PLLMF + 1) / 2.
At PCI Agent mode, when PCI_MODCK = 1, the ratio of CPM_CLK/PCI_CLK should be calculated from PLLMF as follows:
PLLMF = 3 > CPM_CLK / PCI_CLK = 4
PLLMF = 5 > CPM_CLK / PCI_CLK = 6
PLLMF = 7 > CPM_CLK / PCI_CLK = 8
PLLMF = 9 > CPM_CLK / PCI_CLK = 5
PLLMF = B > CPM_CLK / PCI_CLK = 6
10.5.1
Core PLL Configurations
Table 10-4 shows SCMR[CORECNF] bit values and translations to the core PLL mode.
Table 10-4. 60x Bus-to-Core Frequency
SCMR[CORECNF]
Bus-to-Core Multiplier
0x04, 0x05, 0x15
2x
0x06, 0x11
2.5x
0x08, 0x10
3x
0x0E, 0x1E
3.5x
0x0A, 0x1A
4x
0x07, 0x17
4.5x
0x0B, 0x1B
5x
0x09, 0x19
5.5x
0x0D, 0x1D
6x
0x12
6.5x
0x14
7x
0x16
7.5x
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
10-8
Freescale Semiconductor
Clocks and Power Control
Table 10-4. 60x Bus-to-Core Frequency (continued)
10.6
SCMR[CORECNF]
Bus-to-Core Multiplier
0x1C
8x
0x03, 0x13
PLL off/bypassed
0x0F, 0x1F
PLL off
Clock Configuration Modes
The MPC8280 has three clocking modes: local, PCI host, and PCI agent. The clocking mode is set
according to three input pins—PCI_MODE, PCI_CFG[0], PCI_MODCK.
In each clocking mode, the configuration of bus, core, PCI, and CPM frequencies is determined by seven
bits during the power-on reset—three hardware configuration pins (MODCK[1–3]) and four bits from
hardware configuration word[28–31] (MODCK_H). Both the PLLs and the dividers are set according to
the selected MPC8280 clock operation mode.
For further information and complete lists of each clock mode’s possible clock configurations, see
Section 7, “Clock Configuration Modes,” in the MPC8280 PowerQUICC II Family Hardware
Specifications (order number: MPC8280EC).
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
10-9
Clocks and Power Control
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
10-10
Freescale Semiconductor
Chapter 11
Memory Controller
The memory controller is responsible for controlling a maximum of twelve memory banks sharing a high
performance SDRAM machine, a general-purpose chip-select machine (GPCM), and three
user-programmable machines (UPMs). It supports a glueless interface to synchronous DRAM (SDRAM),
SRAM, EPROM, flash EPROM, burstable RAM, regular DRAM devices, extended data output DRAM
devices, and other peripherals. This flexible memory controller allows the implementation of memory
systems with very specific timing requirements.
• The SDRAM machine provides an interface to synchronous DRAMs, using SDRAM pipelining,
bank interleaving, and back-to-back page mode to achieve the highest performance.
• The GPCM provides interfacing for simpler, lower-performance memory resources and
memory-mapped devices. The GPCM has inherently lower performance because it does not
support bursting. For this reason, GPCM-controlled banks are used primarily for boot-loading and
access to low-performance memory-mapped peripherals.
• The UPM supports address multiplexing of the external bus, refresh timers, and generation of
programmable control signals for row address and column address strobes to allow for a glueless
interface to DRAMs, burstable SRAMs, and almost any other kind of peripheral. The refresh
timers allow refresh cycles to be initiated. The UPM can be used to generate different timing
patterns for the control signals that govern a memory device. These patterns define how the
external control signals behave during a read, write, burst-read, or burst- write access request.
Refresh timers are also available to periodically generate user-defined refresh cycles.
Unless stated otherwise, this chapter describes the 60x bus memory controller. The local bus memory
controller provides the same functionality as the 60x bus memory controller except 64-bit port size, ECC,
and external master support.
The MPC8280 supports the following new features as compared to the MPC860 and MPC850.
• The synchronous DRAM machine enables back-to-back memory read or write operations using
page mode, pipelined operation and bank interleaving for high-performance systems.
• The memory controller supports the local bus and the 60x bus in parallel. The 60x bus and the local
bus share twelve memory banks as well as two SDRAM machines, three user-programmable
machines (UPMs) and GPCMs.
• The memory controller supports atomic operation.
• The memory controller supports read-modify-write (RMW) data parity check.
• The memory controller supports ECC data check and correction.
• Two data buffer controls (one for the local bus).
• ECC/parity byte select pin, which enables a fast, glueless connection to ECC/RMW-parity devices.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
11-1
Memory Controller
•
•
•
18-bit address and 32-bit local data bus memory controller. The local bus memory controller
supports the following:
— 8-, 16-, and 32-bit port sizes
— Parity checking and generation
— Ability to work in parallel with the 60x bus memory controller
Flexible chip-select assignment—The 60x bus and local bus share twelve chip-select lines
(controlled by a memory controller bank). The user can allocate the twelve banks as needed
between the 60x bus and the local bus.
Flexible UPM assignment—The user can assign any of the three UPMs to the 60x bus or the Local
bus
Figure 11-1 shows the dual-bus architecture.
MPC8280
CPM/PCI
External
Master
Core
60x Address [0–31]
60x Address
Bus Interface
A[0–31]
60x Data[0–63]
60x Data
Bus Interface
D[0–63]
60x Memory
Control Signals
SDRAM
Local
Slave
3 UPM
Arrays
Local
Memory
Controller
60x
Memory
Devices
GPCM
2Æ1
60x-to-Local
Transactions
60x
Memory
Controller
Address Decoders
60x
Slave
GPCM
CS[0–11]
Local Memory
Control Signals
SDRAM
CPM/Local
Master
LA[14–31]
Local Address [0–31]
Local Address
Bus Interface
LD[0–31]
Local Data [0–63]
Local Data
Bus Interface
Local
Memory
Devices
Figure 11-1. Dual-Bus Architecture
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
11-2
Freescale Semiconductor
Memory Controller
11.1
Features
The memory controller’s main features are as follows:
• Twelve memory banks
— 32-bit address decoding with mask
— Variable block sizes (32 Kbytes to 4 Gbytes)
— Three types of data errors check/correction:
– Normal odd/even parity
– Read-modify-write (RMW) odd/even parity for single accesses
– ECC
— Write-protection capability
— Control signal generation machine selection on a per-bank basis
— Flexible chip-select assignment between the 60x bus and the local bus
— Supports internal or external masters on the 60x bus
— Data buffer controls activated on a per-bank basis
— Atomic operation
— Extensive external memory-controller/bus-slave support
— ECC/parity byte-select
— Data pipeline to reduce data setup time for synchronous devices
• Synchronous DRAM machine (60x or local bus)
— Provides the control functions and signals for glueless connection to JEDEC-compliant
SDRAM devices
— Back-to-back page mode for consecutive, back-to-back accesses
— Supports 2-, 4- and 8-way bank interleaving
— Supports SDRAM port size of 64-bit (60x only), 32-bit, 16-bit and 8-bit
— Supports external address and/or command lines buffering
• General-purpose chip-select machine (GPCM)—60x or local bus
— Compatible with SRAM, EPROM, FEPROM, and peripherals
— Global (boot) chip-select available at system reset
— Boot chip-select support for 8-, 16-, 32-, and 64-bit devices
— Minimum two clock accesses to external device
— Eight byte write enable signals (WE)—four on the local bus
— Output enable signal (OE)
— External access termination signal (GTA)
• Three UPMs
— Each machine can be assigned to the 60x or local bus.
— Programmable-array-based machine controls external signal timing with a granularity of up to
one quarter of an external bus clock period
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
11-3
Memory Controller
— User-specified control-signal patterns run when an internal or external master requests a
single-beat or burst read or write access.
— UPM refresh timer runs a user-specified control signal pattern to support refresh
— User-specified control-signal patterns can be initiated by software
— Each UPM can be defined to support DRAM devices with depths of 64, 128, 256, and 512
Kbytes, and 1, 2, 4, 8, 16, 32, 64, 128, and 256 Mbytes
– Chip-select line
– Byte-select lines
– Six external general-purpose lines
— Supports 8-, 16-, 32-, and 64-bit memory port sizes, 8-, 16-, and 32-bit port sizes on the local
bus
— Page mode support for successive transfers within a burst
— Internal address multiplexing for all on-chip bus masters supporting 64-, 128-, 256-, and
512-Kbyte, and 1-, 2-, 4-, 8-, 16-, 32-, 64-, 128-, 256-Mbyte page banks
11.2
Basic Architecture
The memory controller consists of three basic machines:
• Synchronous DRAM machine
• General-purpose chip-select machine (GPCM)
• Three UPMs
Each bank can be assigned to any one of these machines via BRx[MS] as shown in Figure 11-2. The MS
and MxMR[BSEL] bits (for UPMs) assign banks to the 60x bus or local bus, as shown in Figure 11-2..
Addresses are decoded by comparing (A[0–16] bit-wise and ORx[AM]) with BRx[BA]. If an address
match occurs in multiple banks, the lowest numbered bank has priority. However, if a 60x bus access hits
a bank allocated to the local bus, the access is transferred to the local bus. Local bus access hits to 60x
assigned banks are ignored.
When a memory address matches BRx[BA], the corresponding machine takes ownership of the external
signals that control access and maintains control until the cycle ends.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
11-4
Freescale Semiconductor
Memory Controller
MxMR[BS]
Bank 0
MS
60x
Bank 1
MS
Bank 2
MS
User-Programmable
Machine (A/B/C)
Local
60x SDRAM
Machine
Bank 3
60x
MS
Local SDRAM
Machine
60x General-Purpose
Chip-Select Machine
Bank 10
MS
Bank11
MS
Local General-Purpose
Chip-Select Machine
Local
60x
Local
Figure 11-2. Memory Controller Machine Selection
Some features are common to all machines.
• A 17-bit most-significant address decode on each memory bank
• The block size of each memory bank can vary between 32 Kbytes (1 Mbyte for SDRAM) and 4
Gbytes (128 Mbytes for SDRAM).
• Normal parity may be generated and checked for any memory bank.
• Read-modify-write parity may be generated and checked for any memory bank with either 32- or
64-bit port size. Using RMW parity on 32-bit port size bank, requires the bus to be in strict 60x
mode (BCR[ETM] = 0. See Section 4.3.2.1, “Bus Configuration Register (BCR).”
• ECC may be generated and checked for any memory bank with a 64-bit port size
• Each memory bank can be selected for read-only or read/write operation.
• Each memory bank can use data pipelining, which reduces the required data setup time for
synchronous devices.
• Each memory bank can be controlled by an external memory controller or bus slave.
The memory controller functionality minimizes the need for glue logic in MPC8280-based systems. In
Figure 11-3, CS0 is used with the 16-bit boot EPROM with BR0[MS] defaulting to select the GPCM. CS1
is used as the RAS signal for 64-bit DRAM with BR1[MS] configured to select UPMA. BS[0–7] are used
as CAS signals on the DRAM.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
11-5
Memory Controller
EPROM
MPC8280
Address
GPCM
CS0
GPL2/OE
BS/WE[0–7]
Data
Address
CE
OE
WE
Data
DRAM
Address
CS1
UPMA
GPLx
RAS
CAS[0–7]
W
Data
Figure 11-3. Simple System Configuration
Implementation differences between the supported machines are described in the following:
• The SDRAM machine provides a glueless interface to JEDEC-compliant SDRAM devices, and
using SDRAM pipelining, page mode, and bank interleaving delivers very high performance. To
allow fine tuning of system performance, the SDRAM machine provides two types of page modes
selectable per memory bank:
— Page mode for consecutive back-to-back accesses (normal operation)
— Page mode for intermittent accesses
SDRAM machines are available on the 60x and local buses; each memory bank can be assigned to
any SDRAM machine.
• The GPCM provides a glueless interface to EPROM, SRAM, flash EPROM (FEPROM), and other
peripherals. The GPCM is available on both buses on CS[0–11]. CS0 also functions as the global
(boot) chip-select for accessing the boot EPROM or FLASH device. The chip-select allows 0 to 30
wait states.
• The UPMs provide a flexible interface to many types of memory devices. Each UPM can control
the address multiplexing for accessing DRAM devices and the timings of BS[0–7] and GPL. Each
UPM can be assigned either to the 60x or to the local bus. Each memory bank can be assigned to
any UPM.
Each UPM is a programmable RAM-based machine. The UPM toggles the memory controller
external signals as programmed in RAM when an internal or external master initiates any external
read or write access. The UPM also controls address multiplexing, address increment, and transfer
acknowledge (TA) assertion for each memory access. The UPM specifies a set of signal patterns
for a user-specified number of clock cycles. The UPM RAM pattern run by the memory controller
is selected according to the type of external access transacted. At every clock cycle, the logical
value of the external signals specified in the RAM array is output on the corresponding UPM pins.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
11-6
Freescale Semiconductor
Memory Controller
Figure 11-4 shows a basic configuration.
Internal/External Memory Access Request Select
Address (A),
Address
Type (AT)
Address
Comparator
Bank Select
MS/BS
Fields
SDRAM Machine
UPMx
GPCM
Signals
Timing
Generator
MUX
External Signals
Figure 11-4. Basic Memory Controller Operation
The SDRAM mode registers (LSDMR and PSDMR) define the global parameters for the 60x and local
SDRAM devices. Machine A/B/C mode registers (MxMR) define most of the global features for each
UPM. GPCM parameters are defined in the option register (ORx). Some SDRAM and UPM parameters
are also defined in ORx.
11.2.1
Address and Address Space Checking
The defined base address is written to the BRx. The bank size is written to the ORx. Each time a bus cycle
access is requested on the 60x or local bus, addresses are compared with each bank. If a match is found on
a memory controller bank, the attributes defined in the BRx and ORx for that bank are used to control the
memory access. If a match is found in more than one bank, the lowest-numbered bank handles the memory
access (that is, bank 0 has priority over bank 1).
NOTE
Although 60x bus accesses that hit a bank allocated to the local bus are
transferred to the local bus, local bus access hits to banks allocated to the
60x bus are ignored. 60x-to-local bus transactions have priority over regular
memory bank hits.
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
11-7
Memory Controller
11.2.2
Page Hit Checking
The SDRAM machine supports page-mode operation. Each time a page is activated on the SDRAM
device, the SDRAM machine stores its address in a page register. The page information, which the user
writes to the ORx register, is used along with the bank size to compare page bits of the address to the page
register each time a bus-cycle access is requested. If a match is found together with bank match, the bus
cycle is defined as a page hit. An open page is automatically closed by the SDRAM machine if the bus
becomes idle, unless ORx[PMS] is set.
11.2.3
Error Checking and Correction (ECC)
ECC can be configured for any bank as long as it is assigned to the 60x bus and is connected to a 64-bit
port size memory. ECC is generated and checked on a 64-bit basis using DP[0–7] for the bank if
BRx[DECC] = 11. If ECC is used, single errors can be corrected and all double-bit errors can be detected.
11.2.4
Parity Generation and Checking
Parity can be configured for any bank, if it is preferred. Parity is generated and checked on a per-byte basis
using DP[0–7] or LDP[0–3] for the bank if BR[DECC] = 01 for normal parity and 10 for RMW parity.
SIUMCR[EPAR] determines the global type of parity (odd or even).
Note that RMW parity can be used only for 32- or 64-bit port size banks. Also, using RMW parity on a
32-bit port size bank requires that the bus is placed in strict 60x mode. This is done by setting BCR[ETM]
(BCR[LETM] for the local bus). Refer to Section 4.3.2.1, “Bus Configuration Register (BCR).”
NOTE: RMW Parity and ECC Modes and Pipelined Addresses
Due to design constraints, using RMW parity or ECC modes and pipelined
addresses (BCR[PLDP] = 0) on the SDRAM interface, requires that the
PSDMR[CL] will be set to 10, choosing CAS latency of 2. If CAS latency
of 3 is needed, use BCR[PLDP] = 1 for a pipeline depth of zero.
When the MPC8280 is decoding a 60x read transaction into one of its internal memory-mapped registers
or dual-port RAM that was originated by an external 60x master, it will generate parity bits along with the
data bytes on DP[0–7]. The type of parity (odd or even) is determined by the SIUMCR[EPAR]
programming.
11.2.5
Transfer Error Acknowledge (TEA) Generation
The memory controller asserts the transfer error acknowledge signal (TEA) in the following cases:
• An unaligned or burst access is attempted to internal MPC8280 space (registers or dual-port
RAM). Note that the dual-port RAM cannot be accessed via bursts.
• The core or an external master attempts a burst access to the local bus address space
• A bus monitor timeout
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
11-8
Freescale Semiconductor
Memory Controller
11.2.6
Machine Check Interrupt (MCP) Generation
The memory controller asserts machine check interrupt (MCP) in the following cases:
• A parity error
• An ECC double-bit error
• An ECC single bit error when the maximum number of ECC errors has been reached
11.2.7
Data Buffer Controls (BCTLx and LWR)
The memory controller provides two data buffer controls for the 60x bus (BCTL0 and BCTL1) and one
for the local bus (LWR). These controls are activated when a GPCM- or UPM-controlled bank is accessed
and can be disabled by setting ORx[BCTLD]. An access to an SDRAM-machine controlled bank does not
activate the BCTLx controls. The BCTL signals are asserted on the rising edge of CLKIN on the first cycle
of the memory controller operation. They are negated on the rising edge of CLKIN after the last assertion
of PSDVAL of the access is asserted. (See Section 11.2.13, “Partial Data Valid Indication (PSDVAL).”) If
back-to-back memory controller operations are pending, BCTLx is not negated.
The BCTL signals have a programmable polarity. See Section 4.3.2.6, “SIU Module Configuration
Register (SIUMCR).”
11.2.8
Atomic Bus Operation
The MPC8280 supports the following kinds of atomic bus operations BRx[ATOM]:
• Read-after-write (RAWA). When a write access hits a memory bank in which ATOM = 01, the
MPC8280 locks the bus for the exclusive use of the accessing master (internal or external).
While the bus is locked, no other device can be granted the bus. The lock is released when the
master that created the lock accesses the same bank with a read transaction. If the master fails to
release the lock within 256 bus clock cycles, the lock is released and a special interrupt is
generated. This feature is intended for CAM operations.
• Write-after-read (WARA). When a read access hits a memory bank in which ATOM = 10, the
MPC8280 locks the bus for the exclusive use of the accessing master (internal or external).
During the lock period, no other device can be granted bus mastership. The lock is released when
the device that created the lock access the same bank with a write transaction. If the device fails to
release the lock within 256 bus clock cycles, the lock is released and a special interrupt is
generated.
NOTE
This mechanism does not replace the PowerPC reservation mechanism.
11.2.9
Data Pipelining
Multiple-MPC8280 systems that use data checking, such as ECC or parity, face a timing problem when
synchronous memories, such as SDRAM, are used. Because these devices can output data every cycle and
because the data checking requires additional data setup time, the timing constraints are extremely hard to
meet. In such systems, the user should set the data pipelining bit, BRx[DR]. This creates data pipelining
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
11-9
Memory Controller
of one stage within the memory controller in which the data check calculations are done, thus eliminating
the additional data setup time requirement.
Note that this feature cannot be used with L2 cacheable banks and that in systems that involve both
MPC8280-type masters and 60x compatible master, this feature can still be used on the 60x bus under the
following restrictions:
1. The arbiter and the memory controller are in the same MPC8280.
2. The register field BCR[NPQM] is setup correctly.
See “Section 11.9, “External Master Support (60x-Compatible Mode),” and “Section 4.3.2.1, “Bus
Configuration Register (BCR).”
11.2.10 External Memory Controller Support
The MPC8280 has an option to allocate specific banks (address spaces) to be controlled by an external
memory controller or bus slave, while retaining all the bank properties: port size, data check/correction,
atomic operation, and data pipelining. This is done by programming BRx and ORx[AM] and by setting the
external memory controller bit, BRx[EMEMC]. This action automatically assigns the bank to the 60x bus.
For an access that hits the bank, all bus acknowledgment signals (such as AACK, PSDVAL, and TA) and
the memory-device control strobes are driven by an external memory controller or slave. If the device that
initiates the transaction is internal to the MPC8280, the memory controller handles the port size, data
checking, atomic locking, and data pipelining as if the access were governed by it.
This feature allows multiple MPC8280 systems to be connected in 60x-compatible mode without losing
functionality and performance. It also makes it easy to connect other 60x-compatible slaves on the 60x bus.
11.2.11 External Address Latch Enable Signal (ALE)
The memory controller provides control for an external address latch, needed on the 60x bus in 60x
compatible mode. ALE is asserted for one clock cycle on the first cycle of each memory-controller
transaction. In this section, whenever ALE is not on a timing diagram, assume that it is asserted on the first
cycle in which CS can be asserted.
NOTE
ALE is relevant only on the 60x bus and only in 60x-compatible mode.
11.2.12 ECC/Parity Byte Select (PBSE)
Systems that use ECC or read-modify-write parity, require an additional memory device that requires
byte-select like a normal data device. ANDing BS[0–7] through external logic to achieve the logical
function of this byte-select can affect the memory access timing because it adds a delay to the byte-select
path. The MPC8280’s memory controller provides optional byte-select pins that are an internal AND of
the eight byte selects, allowing glueless, faster connection to ECC/RMW-parity devices.
This option is enabled by setting SIUMCR[PBSE], as described in Section 4.3.2.6, “SIU Module
Configuration Register (SIUMCR).”
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
11-10
Freescale Semiconductor
Memory Controller
11.2.13 Partial Data Valid Indication (PSDVAL)
The 60x and local buses have an internal 64-bit data bus. According to the 60x bus specification, TA is
asserted when up to a double word of data is transferred. Because the MPC8280 supports memories with
port sizes smaller than 64 bits, there is a need for partial data valid indication. The memory controller uses
PSDVAL to indicate that data is latched by the memory on write accesses or valid data is present on read
accesses. The quantity of the data depends on the memory port size and the transfer size. The memory
controller accumulates PSDVAL assertions, and when a double word (or the transfer size) is transferred,
the memory controller asserts TA to indicate that a 60x data beat was transferred. Table 11-1 shows the
number of PSDVAL assertions needed for one TA assertion under various circumstances.
Table 11-1. Number of PSDVAL Assertions Needed for TA Assertion
Port Size
Transfer Size
PSDVAL Assertions
TA Assertions
64
Any
1
1
32
Double word
2
1
32
Word/half word/byte (32-bit aligned)
1
1
16
Double Word
4
1
16
Word
2
1
16
Half/byte
1
1
8
Double word
8
1
8
Word
4
1
8
Half
2
1
8
Byte
1
1
Figure 11-5 shows a double-word transfer on 32-bit port size memory.
Clock
External
Data Bus
(32 msb)
Upper 4 bytes
Lower 4 bytes
PSDVAL
Internal
Data Bus
(32 msb)
Internal
Data Bus
(32 lsb)
Upper 4 bytes
Lower 4 bytes
TA
Figure 11-5. Partial Data Valid for 32-Bit Port Size Memory, Double-Word Transfer
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
Freescale Semiconductor
11-11
Memory Controller
11.2.14 BADDR[27:31] Signal Connections
The memory controller uses BADDR[27:31] to interface memory and peripheral devices on the 60x bus
in 60x-compatible mode. Not all the BADDR line are necessarily used.
Use Table 11-2 to determine which BADDR lines are needed for the device connection.
Table 11-2. BADDR Connections
Non-SDRAM
32-Bit Port
Size Device
Any 16-Bit
Port Size
Device
BADDR[x]
Non-SDRAM
64/72-Bit Port
64-/72-Bit Port
Size SDRAM
Size Device
BADDR[27]
N.C.
Connected
N.C.
Connected
Connected
Connected
BADDR[28]
N.C.
Connected
N.C.
Connected
Connected
Connected
BADDR[29]
N.C.
N.C
N.C.
Connected
Connected
Connected
BADDR[30]
N.C.
N.C
N.C.
N.C
Connected
Connected
BADDR[31]
N.C.
N.C
N.C.
N.C.
N.C.
Connected
11.3
32-Bit Port
Size SDRAM
Any 8-Bit Port
Size Device
Register Descriptions
Table 11-3 lists registers used to control the 60x bus memory controller.
Table 11-3. 60x Bus Memory Controller Registers
Abbreviation
Name
Reference
BR0–BR11
Base register banks 0–11
Section 11.3.1
OR0–OR11]
Option register banks 0–11
Section 11.3.2
PSDMR
60x bus SDRAM machine mode register
Section 11.3.3
LSDMR
Local bus SDRAM machine mode register
Section 11.3.4
MAMR
UPMA mode register
Section 11.3.5
MBMR
UPMB mode register
MCMR
UPMC mode register
MDR
Memory data register
Section 11.3.6
MAR
Memory address register
Section 11.3.7
Memory refresh timer prescaler register
Section 11.3.12
PURT
60x bus assigned UPM refresh timer
Section 11.3.8
PSRT
60x bus assigned SDRAM refresh timer
Section 11.3.10
LURT
Local bus assigned UPM refresh timer
Section 11.3.9
LSRT
Local bus assigned SDRAM refresh timer
Section 11.3.11
TESCRx
60x bus error status and control registers
Section 11.3.13
LTESCRx
Local bus error status and control regs
Section 11.3.14
MPTPR
MPC8280 PowerQUICC II Family Reference Manual, Rev. 1
11-12
Freescale Semiconductor
Memory Controller
Base Registers (BRx)
11.3.1
The base registers (BR0–BR11) contain the base address and address types that the memory controller uses
to compare the address bus value with the current address accessed. Each register also includes a memory
attribute and selects the machine for memory operation handling. Figure 11-7 shows the BRx register
format.
0
15
Field
BA
Reset
0000_0000_0000_0000
R/W
R/W
Addr
0x10100 (BR0); 0x10108 (BR1); 0x10110 (BR2); 0x10118 (BR3); 0x10120 (BR4); 0x10128 (BR5);
0x10130 (BR6); 0x10138 (BR7); 0x10140 (BR8); 0x10148 (BR9); 0x10150 (BR10); 0x10158 (BR11)
16
17
Field BA
Reset
18
19
—
000
20
PS
1
21
22
DECC
see note
23
24
WP
26
MS
27
EMEMC
0000_000
28
1
see note
29
ATOM
000
30
31
DR
V1
see note
R/W
R/W
Addr
0x10102 (BR0); 0x1010A (BR1); 0x10112 (BR2); 0x1011A (BR3); 0x10122 (BR4); 0x1012A (BR5);
0x10132 (BR6); 0x1013A (BR7); 0x10142 (BR8); 0x1014A (BR9); 0x10152 (BR10); 0x1015A (BR11)
1For
BR0 these fields depend on reset configuration sequence. See Section 5.4.1, “Hard Reset Configuration Word.”
For BR1–11, these fields are cleared at reset.
Figure 11-6. Base Registers (BRx)
Table 11-4 describes BRx fields.
Table 11-4. BRx Field Descriptions
Bits
Name
Description
0–16
BA
Base address. The upper 17 bits of each base address register are compared to the address on
the address bus to determine if the bus master is accessing a memory bank controlled by the
memor