MIL-PRF-38534 CERTIFIED M.S.KENNEDY CORP. DUAL RAD HARD +/VOLTAGE REGULATOR 5911RH SERIES 4707 Dey Road Liverpool, N.Y. 13088 (315) 701-6751 FEATURES: Total Dose Tested to 300K RAD(Si) Internal Thermal Overload Protection Output Current to 1.5 Amps Output Voltage Internally Trimmed to ±1% Accuracy Lead Form Options: Straight and Gull Wing Alternate Voltage Combinations Available MSK591XRH DESCRIPTION: MSK591XRHG The MSK 5911RH series are dual Radiation Hardened +/- voltage regulators offering low dropout and output accuracy to ±1% maximum. Excellent line and load regulation characteristics ensure highly accurate performance. The MSK 5911RH series regulators are equipped with internal thermal overload protection. The devices are packaged in a space efficient 20 pin flatpack with two lead form options, straight and gull wing. EQUIVALENT SCHEMATIC TYPICAL APPLICATIONS PIN-OUT INFORMATION 1 2 3 4 5 6 7 8 9 10 Switching Power Supply Post Regulators Constant Voltage/Current Regulators High Efficiency Linear Regulators 1 -VRTN -VOUT -VOUT -VOUT -VOUT +VRTN +VOUT +VOUT +VOUT +VOUT 20 19 18 17 16 15 14 13 12 11 -VIN -VIN -VIN -VIN -Ccomp +Ccomp +VIN +VIN +VIN +VIN Rev. B 1/06 8 ABSOLUTE MAXIMUM RATINGS +VIN -VIN PD +IOUT -IOUT TJ +Input Voltage (VIN-VOUT) -Input Voltage (VIN-VOUT) Power Dissipation +Output Current -Output Current Junction Temperature ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ +40VDC -30VDC Internally Limited 1.5A 1.5A +150°C ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ TST Storage Temperature Range TLD Lead Temperature Range (10 Seconds) TC Case Operating Temperature MSK 5911RH-5919RH MSK 5911RH-5919RH(K/H/E) ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ -65°C to +150°C 300°C ○ ○ ○ ○ ○ ○ -40°C to +85°C -55°C to +125°C ○ ELECTRICAL SPECIFICATIONS Parameter Test Conditions Group A MSK 591XRH K/H/E 3 Subgroup Typ. Min. Max. 4 7 MSK 591XRH 2 Units Min. Typ. Max. POSITIVE OUTPUT REGULATORS: 1 - ±0.2 ±1.0 - ±0.2 ±1.5 % 2,3 - ±0.8 ±3.0 - - - % 1 - 1.6 3.0 - 1.6 3.5 V 2,3 - 1.9 3.0 - - - V 1 - ±0.2 ±2.0 - ±0.2 ±2.5 % V IN=VOUT+3V 2,3 - ±0.4 ±2.5 - - - % IOUT=10mA 1 - ±0.6 ±1.5 - ±0.6 ±2.0 % VOUT+3V≤V IN≤35V 2,3 - ±1.0 ±2.5 - - - % JUNCTION TO CASE @ 125°C - - 9.5 10.5 - 9.5 1 - ±0.2 ±1.0 - ±0.2 ±1.5 % 2,3 - ±0.8 ±3.0 - - - % 1 - 1.9 3.0 - 1.9 3.0 V 2,3 - 1.5 3.0 - - - V 10mA≤IOUT≤0.5A 1 - ±0.2 ±2.0 - ±0.2 ±2.5 % VIN=VOUT -3V 2,3 - ±0.4 ±2.5 - - - % IOUT=10mA 1 - ±0.1 ±1.5 - ±0.1 ±2.0 % -30V≤V IN≤VOUT-3V 2,3 - ±0.2 ±2.5 - - - % - - TBD TBD - TBD TBD °C/W Output Voltage Tolerance IOUT=10mA; VIN=VOUT+3V IOUT=0.5A; ∆V OUT=1% Dropout Voltage 10mA≤IOUT≤0.5A Load Regulation Line Regulation Thermal Resistance 1 11.0 °C/W NEGATIVE OUTPUT REGULATORS: Output Voltage Tolerance Dropout Voltage Load Regulation Line Regulation Thermal Resistance 1 IOUT=10mA; VIN=VOUT -3V IOUT=0.5A; ∆V OUT=1% JUNCTION TO CASE @ 125°C PART 5 NUMBER NOTES: 1 2 3 4 5 6 7 8 Guaranteed by design but not tested. Typical parameters are representative of actual device performance but are for reference only. Industrial grade and "E" suffix devices shall be tested to subgroup 1 unless otherwise specified. Military grade devices shall be 100% tested to subgroups 1,2 and 3. Subgroup 1 TA=TC=+25°C Subgroup 2 TA=TC=+125°C Subgroup 3 TA=TC=-55°C Please consult the factory if alternate output voltages are required. For positive regulator, output decoupled to ground using 1µF minimum tantalum capacitor unless otherwise specified. For negative regulator, output decoupled to ground using 1µF minimum tantanlum capacitor. Consult factory for post radiation limits. Continuous operation at or above absolute maximum ratings may adversly effect the device performance and/or life cycle. 2 OUTPUT VOLTAGES POSITIVE NEGATIVE MSK5911 5.0 5.0 MSK5912 5.0 5.2 MSK5913 12.0 5.0 MSK5914 12.0 12.0 MSK5915 15.0 15.0 MSK5916 15.0 5.0 MSK5917 5.0 12.0 MSK5918 5.0 15.0 MSK5919 10.0 10.0 Rev. B 1/06 APPLICATION NOTES TYPICAL APPLICATION CIRCUIT CAPACITOR SELECTION POSITIVE REGULATOR INPUT CAPACITOR: An input bypass capacitor is recommenced when using the MSK 5911 series regulators. This is especially true if the regulator is located farther than 6 inches from the power supply filter capacitors. For most applications a 1µF solid tantalum capacitor will be suitable. OUTPUT CAPACITOR: A minimum of a 1µF solid tantalum capacitor should also be used at the output to insure stability. Any increase of this output capacitor larger than 10µF will only improve output impedance. LOAD REGULATION It is important to keep the output connection between the regulator and the load as short as possible since this directly affects the load regulation. For example, if 20 gauge wire were used which has a resistance of about 0.008 ohms per foot, this would result in a drop of 8mV/ft at 1Amp of load current. It is also important to follow the capacitor selection guidelines to achieve best performance. +CCOMP CAPACITOR: For improved ripple rejection, +Ccomp can be bypassed to ground with a 10µF tantalum capacitor. This bypass capacitor will provide 80dB ripple rejection. Increased capacitance above 10µF does not improve the ripple rejection at frequencies above 120Hz. If the Ccomp bypass capacitor is used, it may be necessary to add a protection diode to protect the regulator from capacitor discharge damage. See Typical Applications Circuit for clarification. If the bypass capacitor is not used, it should be left open since it is internally connected to the regulator. HEAT SINKING To determine if a heat sink is required for your application and if so, what type, refer to the thermal model and governing equation below. Governing Equation: Tj = Pd x (Rθjc + Rθcs + Rθsa) + Ta WHERE Tj = Junction Temperature Pd = Total Power Dissipation Rθjc = Junction to Case Thermal Resistance Rθcs = Case to Heat Sink Thermal Resistance Rθsa = Heat Sink to Ambient Thermal Resistance Tc = Case Temperature Ta = Ambient Temperature Ts = Heat Sink Temperature NEGATIVE REGULATOR INPUT CAPACITOR: Once again, if the regulator will be farther than 6 inches from power supply filter capacitors, then an input capacitor will be required on the negative regulator. It is recommended that a 1µF solid tantalum capacitor be used. EXAMPLE: OUTPUT CAPACITOR: A minimum of a 1µF solid tantalum capacitor should also be used at the output to insure stability. Any increase of this output capacitor larger than 10µF will only improve output impedance. This example demonstrates an analysis where the output currents are at 0.5 amp each and both inputs are 8V. Conditions for MSK 5911RH: +Vin = +8.0V; Iout = 0.5A Positive Regulator -CCOMP CAPACITOR: For improved ripple rejection, -Ccomp can be bypassed to ground with a 10µF tantalum capacitor. This bypass capacitor will provide 66dB ripple rejection. Increased capacitance above 10µF does not improve the ripple rejection at frequencies above 120Hz. If the Ccomp bypass capacitor is used, it may be necessary to add a protection diode to protect the regulator from capacitor discharge damage. See Typical Applications Circuit for clarification. If the bypass capacitor is not used, it should be left open since it is internally connected to the regulator. 1.) Assume 45° heat spreading model. 2.) Find positive regulator power dissipation: Pd = (Vin - Vout)(Iout) Pd = (+8V-5V)(0.5A) Pd = 1.5W 3.) For conservative design, set Tj = +125°C Max. 4.) For this example, worst case Ta = +90°C. 5.) Rθjc = 10.5°C/W from the Electrical Specification Table. 6.) Rθcs = 0.15°C/W for most thermal greases. 7.) Rearrange governing equation to solve for Rθsa: Rθsa= ((Tj - Ta)/Pd) - (Rθjc) - (Rθcs) = (125°C-90°C)/1.5W - 10.5°C/W - 0.15°C/W = 12.7°C/W The same exercise must be performed for the negative regulator. 3 Rev. B 1/06 TYPICAL PERFORMANCE CURVES NOTE: All radiation performance curve test conditions are in accordance with the electrical specifications table (page 2). 4 Rev. B 1/06 TYPICAL PERFORMANCE CURVES CONT'D NOTE: All radiation performance curve test conditions are in accordance with the electrical specifications table (page 2). 5 Rev. B 1/06 MECHANICAL SPECIFICATIONS MSK591XRH Weight=4.3 Grams Typical NOTE: ALL DIMENSIONS ARE ±0.010 INCHES UNLESS OTHERWISE LABELED. ESD Triangle indicates pin 1. ORDERING INFORMATION Part Number Screening Level MSK591XRH Industrial MSK591XHRH MIL-PRF-38534 CLASS H MSK591XKRH MIL-PRF-38534 CLASS K MSK591XERH EXTENDED RELIABILITY X - Designates voltage selection (MSK 5911-5919) 6 Rev. B 1/06 MECHANICAL SPECIFICATIONS CONTINUED MSK591XRHG Weight=4.2 Grams Typical NOTE: ALL DIMENSIONS ARE ±0.010 INCHES UNLESS OTHERWISE LABELED. ESD Triangle indicates pin 1. ORDERING INFORMATION Part Number Screening Level MSK591XRHG Industrial MSK591XHRHG MIL-PRF-38534 CLASS H MSK591XKRHG MIL-PRF-38534 CLASS K MSK591XERHG EXTENDED RELIABILITY X - Designates voltage selection (MSK 5911-5919) M.S. Kennedy Corp. 4707 Dey Road, Liverpool, New York 13088 Phone (315) 701-6751 Fax (315) 701-6752 www.mskennedy.com The information contained herein is believed to be accurate at the time of printing. MSK reserves the right to make changes to its products or specifications without notice, however and assumes no liability for the use of its products. Please visit our website for the most recent revision of this datasheet. Contact MSK for MIL-PRF-38534 Class H, Class K and Appendix G (radiation) status. 7 Rev. B 1/06