FDC10 I s o l a t e d a n d R e gulated 10 WATT Modular DC/DC Converters series Wide 2 : 1 Input Range High Efficiency Regulated Outputs 1600V Isolation Full EMI Shielding Standard Pinouts Unit measures 1”W x 2”L x 0.375”H Model Number SINGLE OUTPUT FDC10-12S33 FDC10-24S33 FDC10-48S33 FDC10-12S05 FDC10-24S05 FDC10-48S05 FDC10-12S12 FDC10-24S12 FDC10-48S12 FDC10-12S15 FDC10-24S15 FDC10-48S15 DUAL OUTPUT FDC10-12D05 FDC10-24D05 FDC10-48D05 FDC10-12D12 FDC10-24D12 FDC10-48D12 FDC10-12D15 FDC10-24D15 FDC10-48D15 Output Voltage Output Amps Input Range 3.3 VDC 2 2 2 2 2 2 0.83 0.83 0.83 0.67 0.67 0.67 9-18 VDC 18-36 VDC 36-72 VDC 9-18 VDC 18-36 VDC 36-72 VDC 9-18 VDC 18-36 VDC 36-72 VDC 9-18 VDC 18-36 VDC 36-72 VDC +/-1 +/-1 +/-1 +/-0.416 +/-0.416 +/-0.416 +/-0.333 +/-0.333 +/-0.333 9-18 VDC 18-36 VDC 36-72 VDC 9-18 VDC 18-36 VDC 36-72 VDC 9-18 VDC 18-36 VDC 36-72 VDC 5 VDC 12 VDC 15 VDC +/-5 VDC +/-12 VDC +/-15 VDC Order On-Line! WWW.ASTRODYNE.COM astrodyne.com 300 Myles Standish Blvd., Taunton, MA 02780 Ph: 1-800-823-8082 Fax: 508-823-8181 FDC10 I s o l a t e d a n d R e gulated 10 WATT Modular DC/DC Converters GENERAL SPECIFICATIONS INPUT SPECIFICATIONS Input Voltage Ranges: Input Filter series 12 VDC Nominal 24 VDC Nominal 48 VDC Nominal Pi Type 9-18 VDC 18-36 VDC 36-72 VDC Input-Out Isolation In/Out Capacitance Isolation Resistance Efficiency Switching Frequency 1600VDC 1000 pF 10000 M Ohms 80%, typ 300Khz OUTPUT SPECIFICATIONS ENVIRONMENTAL SPECIFICATIONS Voltage and Current See Selection Chart Load Regulation singles: +/-1% 10% - FL duals: +/-2% Line Regulation +/-1% Temperature Coefficient +/-0.02%/DegC Ripple/Noise(Single/Dual) (50 / 75) mV Pk-Pk, typ Voltage Stability +/- 2% Voltage Balance, Dual +/-1% Transient Response Recovery 25% Load Step Change 500 microSeconds Short Circuit Protection Continuous, self-recovering Overvoltage Protection Threshold: 3.3V Output 3.9Volts 5V Output 6.2Volts 12V Output 15Volts 15V Output 18Volts All specifications are typical at nominal input, full load, and 25DegC unless otherwise noted * These are stress ratings. Exposure of the devices to any of these conditions may adversely affect long term reliability. Proper operation under conditions other than the standard operating conditions is neither warranteed nor implied. WWW.ASTRODYNE.COM Oper. Temperature Storage Temperature Maximum Case Temp MTBF -25 to +71 DegC(FL) -55 to +125 DegC * 110 DegC * 1.97 MHrs MIL-HDBK-217F TA=25C FL PHYSICAL SPECIFICATIONS Case Material Construction Weight Nickel-Coated Copper Non-Conductive Base Fully Encapsulated 1.1 oz, (30g) Astrodyne products are not authorized or warranteed for use as critical components in life support systems, equipment used in hazardous environments, nuclear controls systems, or other mission-critical applications. 300 Myles Standish Blvd., Taunton, MA 02780 Ph: 1-800-823-8082 Fax: 508-823-8181 FDC10 I s o l a t e d a n d R e gulated 10 WATT Modular DC/DC Converters MECHANICAL DIMENSIONS OUTPUT DERATING CURVE 0.50 (12.7) DIA. 0.04(1.0) 5 Bottom View 1 2 100 75 50 Nature convection 25 0 -40 -25 -10 0 0.80(20.3) 4 0.40 (10.2) FDC10-48S05 Derating Curve 50 60 70 80 90 100 AMBIENT TEMPERATURE (ºC) 0.60(15.2) 2.00(50.8) 3 0.40 (10.2) OUTPUT POWER (%) 1.00(25.4) 0.40 (10.2) series 0.10(2.5) 0.22(5.6) 0.20(5.1) 1. All dimensions in Inches (mm) Tolerance x.xx±0.02(x.x±0.5) 2. Pin Pitch tolerance ±0.014(0.35) Pin # Single Outputs Dual Outputs 1 2 3 4 5 + Input - Input + Output No Pin - Output + Input - Input + Output Common - Output WWW.ASTRODYNE.COM 300 Myles Standish Blvd., Taunton, MA 02780 Ph: 1-800-823-8082 Fax: 508-823-8181