SynQor BQ55120QZB67xyz-G Industry standard quarter-brick pin-out configuration Datasheet

Technical
Specification
BQ55120QZB67
35-55V
12V
67A
784W
2000V dc
Quarter-brick
Continuous Input
Output
Current
Power
Isolation
DC-DC Converter
®
The BusQor® BQ55120QZx67 bus converter is a nextgeneration, board-mountable, isolated, fixed switching
frequency DC-DC converter that uses synchronous
rectification to achieve extremely high conversion
efficiency. The BusQor series provides an isolated step
down voltage from 48V to 12 or 9.6V intermediate
bus with no regulation in a standard “quarter-brick”
module. BusQor converters are ideal for creating the
mid-bus voltage required to drive point-of-load (nonisolated) converters in intermediate bus architectures.
BQ55120QZB67 Model
Operational Features
•
•
•
•
•
Mechanical Features
High efficiency, 97% at full rated load current
Delivers 67A full power with appropiate derating
Operating input voltage range: 35-55V
Fixed frequency switching provides predictable EMI
No minimum load requirement
• Industry standard quarter-brick pin-out configuration
• Size: 1.51"x 2.34" (38.4 x 59.4mm), height: 0.517" (13.13mm)
• Total Baseplate weight: 2.67 oz (75.7 g)
Protection Features
Control Features
• On/Off control referenced to input side
(negative logic only)
• Inherent current share (by droop method) for high current and
parallel applications.
• Input under-voltage lockout and over-voltage shutdown protects
against abnormal input voltages
• Output current limit and short circuit protection (auto recovery)
• Output over-voltage protection
• Thermal shutdown
Contents
Page No.
Safety Features
• UL 60950-1/R2011-12
• EN60950-1/A2:2013
• CAN/CSA-C22.2 No. 60950-1/A1:2011
Product # BQ55120QZB67
Phone 1-888-567-9596
Baseplated Mechanical Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Compliance & Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Technical Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Applications Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
www.synqor.com
Doc.# 005-0006255 Rev. C
02/10/16
Page 1
Input:
Output:
Current:
Package:
Baseplated Mechanical Diagram
35-55V
12V
67 A
Quarter-brick
1.51 [38.4]
1.100 [27.94]
0.600 [15.24]
0.220
[5.59]
0.517±0.030
[ 13.13±0.76 ]
Overall Height
0.205 [5.21]
5
0.052±0.034
[ 1.32±0.86 ]
Bottomside
Clearance
4
M3 Inserts
3 Places
See Notes 1 & 2
1.150
[29.21]
2.000 1.900
2.34
[48.26]
[59.4] [50.80]
See Note 3
0.16
[4.0]
1
2
3
0.45 [11.5]
0.300 [7.63]
0.600 [15.24]
0.180 [4.57]
NOTES
PIN DESIGNATIONS
1) M3 screws used to bolt unit's baseplate to other surfaces such as
heatsinks must not exceed 0.10" (2.54mm) depth below the surface
of the baseplate.
2) Applied torque per screw should not exceed 6in-lb (0.7nm)
3) Baseplate flatness tolerance is 0.004" (.10mm) TIR for surface
4) Other pin extension lengths available
5) Pins 1-3 are 0.040" (1.02mm) dia. with 0.080" (2.03mm) dia.
standoff shoulders
6) Pins 4 and 5 are 0.062" (1.57mm) dia. with 0.100" (2.54mm) dia.
standoff shoulders
7) All pins: Material: Copper Alloy
Finish: Matte Tin over Nickel plate
8) Undimensioned components are shown for visual reference only
9) Baseplate weight: 2.67 oz (75.7 g) typical
10) All dimensions in inches(mm)
Tolerances: x.xxin +/-0.02 (x.xmm +/-0.5mm)
x.xxxin +/-0.010 (x.xxmm +/-0.25mm)
Product # BQ55120QZB67
Phone 1-888-567-9596
Pin
Name
Function
1 Vin(+) Positive input voltage
2 ON/OFF Logic control input to turn converter on/off.
3 Vin(–) Negative input
4 Vout(–) Negative output
5 Vout(+) Positive output
www.synqor.com
Doc.# 005-0006255 Rev. C
02/10/16
Page 2
Input:
Output:
Current:
Package:
Technical Specification
35-55V
12V
67 A
Quarter-brick
BQ55120QZB67 Electrical Characteristics
Ta = 25 °C, airflow rate = 300 LFM, Vin = 48V dc unless otherwise noted; full operating temperature range is -40 °C to +100 °C base plate temperature
with appropriate power derating. Specifications subject to change without notice.
Parameter
Min.
ABSOLUTE MAXIMUM RATINGS
Input Voltage
Non-Operating
Operating
Isolation Voltage
Input to Output
Operating Temperature
Storage Temperature
Voltage at ON/OFF input pin
INPUT CHARACTERISTICS
Operating Input Voltage Range
Input Under-Voltage Lockout
Turn-On Voltage Threshold
Turn-Off Voltage Threshold
Lockout Voltage Hysteresis
Input Over-Voltage Shutdown
Turn-On Voltage Threshold
Turn-Off Voltage Threshold
Maximum Input Current
No-Load Input Current
Disabled Input Current
Input Reflected-Ripple Current
Input Terminal-Ripple Current
Recommended Input Fuse (see Note 1)
Recommended External Input Capacitance
Input Filter Component Values (L\C)
OUTPUT CHARACTERISTICS
Output Voltage Set Point
Output Voltage Regulation
Over Line
Over Load
Over Temperature
Total Output Voltage Range
Output Voltage Ripple and Noise
Peak-to-Peak
RMS
Operating Output Current Range
Output DC Current-Limit Inception
Output DC Current-Limit Shutdown Voltage
Back-Drive Current Limit while Disabled
Maximum Output Capacitance
EFFICIENCY
100% Load
50% Load
Product # BQ55120QZB67
Typ.
Max.
-1
35
60
55
V
V
-40
-45
-2
2000
100
125
18
V
°C
°C
V
55
V
35
48
33.4
31
2.4
56.9
59.2
16.0
25
300
24.5
140
26.0
40
30
V
V
V
V
V
V
A
mA
mA
mA
mA
A
µF
47
0.22\30
µH\µF
11.8
V
41.7\5.0
4.2\500
1.7\200
%\V
%\mV
%\mV
V
8.200
Phone 1-888-567-9596
Units Notes & Conditions
13.750
125
40
200
67
mV
mV
A
5,000
A
V
mA
µF
0
78
8
10
97
97
www.synqor.com
Continuous
Continuous
Vin = 35 V
RMS through 10µH inductor
RMS, full load
Fast blow external fuse recommended
Typical ESR 0.1-0.2 Ω
Internal values
Io = 0 A
Over sample, line, load, temperature & life
20 MHz bandwidth; see Note 2
Full load
Full load
Subject to thermal derating
Output Voltage 10% Low
Negative current drawn from output
12.0 Vout at 33 A Resistive Load
%
%
Doc.# 005-0006255 Rev. C
02/10/16
Page 3
Input:
Output:
Current:
Package:
Technical Specification
35-55V
12V
67 A
Quarter-brick
BQ55120QZB67 Electrical Characteristics (continued)
Ta = 25 °C, airflow rate = 300 LFM, Vin = 48V dc unless otherwise noted; full operating temperature range is -40 °C to +100 °C base plate temperature
with appropriate power derating. Specifications subject to change without notice.
Parameter
Min.
DYNAMIC CHARACTERISTICS
Output Voltage during Load Current Transient
Step Change in Output Current (0.1 A/µs)
Settling Time
Turn-On Transient
Turn-On Time (with 5mF output capacitance)
Fault Inhibit Time
Output Voltage Overshoot
ISOLATION CHARACTERISTICS
Typ.
Max.
150
100
5
800
0
10
Units Notes & Conditions
mV
µs
50% to 75% to 50% Iout max
To within 1% Vout nom
ms
ms
%
33 A Resistive Load, Vout=90% nom.
Figure E
5 mF load capacitance, 33 A Resistive Load
Isolation Voltage (dielectric strength)
2000
V
See Absolute Maximum Ratings
Isolation Resistance
30
MΩ
Isolation Capacitance (input to output)
1000
pF
See Note 3
Semiconductor Junction Temperature
125
°C
Package rated to 150 °C
Board Temperature
125
°C
UL rated max operating temp 130 °C
Transformer Core Temperature
130
°C
Base Plate Temperature
100
°C
FEATURE CHARACTERISTICS
Switching Frequency
154
175
196
kHz
ON/OFF Control (Option N)
On-State Voltage
-1
0.8
V
Off-State Voltage
2.4
18
V
ON/OFF Control
Application notes Figures A & B
Pull-Up Voltage
3.3
V
Pull-Up Resistance
100
kΩ
Over-Temperature Shutdown OTP Trip Point
140
150
°C
Average PCB Temperature
Over-Temperature Shutdown Restart Hysteresis
10
°C
RELIABILITY CHARACTERISTICS
Calculated MTBF (Telcordia) SR-332, Issue 2
5.4
106 Hrs. 80% load, 200LFM, 40 °C Ta
Calculated MTBF (MIL-217) MIL-HDBK-217F
3.6
106 Hrs. 80% load, 200LFM, 40 °C Ta
Field Demonstrated MTBF
106 Hrs. See our website for details
Note 1: Safety product certification tests were carried out using 30A fast blow fuse. Fuse interruption characteristics have to be taken into account
while designing input traces. User should ensure that Input trace is capable of withstanding fault currents
Note 2: For applications requiring reduced output voltage ripple and noise, consult SynQor applications support (e-mail: [email protected])
Note 3: Isolation capacitance can be added external to the module.
Product # BQ55120QZB67
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006255 Rev. C
02/10/16
Page 4
Input:
Output:
Current:
Package:
Technical Specification
35-55V
12V
67 A
Quarter-brick
Compliance & Testing
Parameter
Notes & Conditions
STANDARDS COMPLIANCE
UL 60950-1/R2011-12
Basic insulation
EN60950-1/A2:2013
CAN/CSA-C22.2 No. 60950-1/A1:2011
Note: An external input fuse must always be used to meet these safety requirements. Contact SynQor for official safety certificates on new
releases or download from the SynQor website.
Parameter
QUALIFICATION TESTING
Life Test
Vibration
Mechanical Shock
Temperature Cycling
Power/Thermal Cycling
Design Marginality
Humidity
Solderability
Product # BQ55120QZB67
# Units
32
5
5
10
5
5
5
15 pins
Phone 1-888-567-9596
Test Conditions
95% rated Vin and load, units at derating point, 1000 hours
10-55 Hz sweep, 0.060" total excursion, 1 min./sweep, 120 sweeps for 3 axis
100g minimum, 2 drops in x, y and z axis
-40 °C to 100 °C, unit temp. ramp 15 °C/min., 500 cycles
Toperating = min to max, Vin = min to max, full load, 100 cycles
Tmin-10 °C to Tmax+10 °C, 5 °C steps, Vin = min to max, 0-105% load
85 °C, 95% RH, 1000 hours, continuous Vin applied except 5 min/day
MIL-STD-883, method 2003
www.synqor.com
Doc.# 005-0006255 Rev. C
02/10/16
Page 5
Input:
Output:
Current:
Package:
Technical Figures
100
35-55V
12V
67 A
Quarter-brick
99.0
95
98.5
90
98.0
Efficiency (%)
Efficiency (%)
85
80
75
70
97.0
35 Vin
25º C
48 Vin
65
96.5
55 Vin
0
10
20
30
40
Load Current (A)
50
60
40º C
55º C
60
96.0
70
Figure 1: Efficiency at nominal output voltage vs. load current for minimum,
nominal, and maximum input voltage at 25°C.
100
200
Air Flow (LFM)
300
16
15
Power Dissipation (W)
20
15
10
35 Vin
5
14
13
12
25º C
11
48 Vin
40º C
55 Vin
55º C
0
0
10
20
30
40
Load Current (A)
50
60
10
100
70
Figure 3: Power dissipation at nominal output voltage vs. load current for
minimum, nominal, and maximum input voltage at 25°C.
200
Air Flow (LFM)
300
400
Figure 4: Power dissipation at nominal output voltage and 60% rated power
vs. airflow rate for ambient air temperatures of 25°C, 40°C, and 55°C (nominal
input voltage).
70
800
60
700
600
50
500
40
Pout (W)
Iout (A)
400
Figure 2: Efficiency at nominal output voltage and 60% rated power vs. airflow
rate for ambient air temperatures of 25°C, 40°C, and 55°C (nominal input
voltage).
25
Power Dissipation (W)
97.5
30
20
400 LFM (2.0 m/s)
300
400 LFM (2.0 m/s)
200
300 LFM (1.5 m/s)
10
400
200 LFM (1.0 m/s)
300 LFM (1.5 m/s)
200 LFM (1.0 m/s)
100
100 LFM (0.5 m/s)
0
100 LFM (0.5 m/s)
0
25
40
50
60
70
25
85
Ambient Air Temperature (ºC)
Phone 1-888-567-9596
Semiconductor
junction
is
50
60temperature 70
within 1°C of surface temperature
85
Ambient Air Temperature (ºC)
Figure 5: Maximum output current derating curve vs. ambient air temperature
(with baseplate only) at different airflow rates with air flowing from output to
input (nominal input voltage).
Product # BQ55120QZB67
40
Figure 6: Maximum output power derating curve vs. ambient air temperature
(with baseplate only) at different airflow rates with air flowing from output to
input (nominal input voltage).
www.synqor.com
Doc.# 005-0006255 Rev. C
02/10/16
Page 6
Input:
Output:
Current:
Package:
Technical Figures
70
800
60
700
600
50
500
40
Pout (W)
Iout (A)
35-55V
12V
67 A
Quarter-brick
30
20
400 LFM (2.0 m/s)
300
400 LFM (2.0 m/s)
200
300 LFM (1.5 m/s)
10
400
200 LFM (1.0 m/s)
300 LFM (1.5 m/s)
200 LFM (1.0 m/s)
100
100 LFM (0.5 m/s)
0
100 LFM (0.5 m/s)
0
25
40
50
60
70
85
25
Ambient Air Temperature (ºC)
40
50
60
70
85
Ambient Air Temperature (ºC)
Figure 7: Maximum output current derating curve vs. ambient air temperature
(with both baseplate and 0.5” heat sink) at different airflow rates with air
flowing from output to input (nominal input voltage).
Figure 8: Maximum output power derating curve vs. ambient air temperature
(with both baseplate and 0.5” heat sink) at different airflow rates with air
flowing from output to input (nominal input voltage).
Figure 9: Turn-on transient at half load (resistive load) (1 ms/div). Load cap:
15µF tantalum capacitor and 5mF ceramic capacitor bank. Input voltage preapplied. Ch 1: Vout (2V/div). Ch 2: ON/OFF input (2 V/div).
Figure 10: Turn-on transient at zero load (1 ms/div). Load cap: 15µF tantalum
capacitor and 5mF ceramic capacitor bank. Ch 1: Vout (2V/div), Ch 2: ON/OFF
input (2 V/div).
Figure 11: Output voltage response to step-change in load current (50%-75%50% of Iout(max); dI/dt = 0.1A/µs). Load cap: 15µF tantalum cap and 1µF
ceramic cap. Ch 1: Vout (1V/div), Ch 2: Iout (25A/div).
Figure 12: Output voltage response to step-change in load current (50%-75%50% of Iout(max): dI/dt = 1A/µs). Load cap: 15µF, 30 mΩ ESR tantalum cap
and 1µF ceramic cap. Ch 1: Vout (1V/div), Ch 2: Iout (25A/div).
Product # BQ55120QZB67
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006255 Rev. C
02/10/16
Page 7
Input:
Output:
Current:
Package:
Technical Figures
Input Reflected
Ripple Current
35-55V
12V
67 A
Quarter-brick
Output Voltage
Ripple
Input Terminal
Ripple Current
source
impedance
iS
iC
DC-DC
Converter
VOUT
VSOURCE
electrolytic
capacitor
electrolytic
capacitor
ceramic
capacitor
Figure 13: Test set-up diagram showing measurement points for Input Terminal
Ripple Current (Figure 14), Input Reflected Ripple Current (Figure 15) and
Output Voltage Ripple (Figure 16).
Figure 14: Input Terminal Ripple Current, ic, at full rated output current and
nominal input voltage with 10µH source impedance and 47µF electrolytic
capacitor (500 mA/div). See Figure 13.
Figure 15: Input reflected ripple current, is, through a 10µH source inductor,
using a 47µF electrolytic input capacitor (20mA/div). See Figure 13.
Figure 16: Output voltage ripple at nominal input voltage and rated load current
(100mV/div). Load capacitance: 1µF ceramic capacitor and 15µF tantalum
capacitor. Bandwidth: 20MHz. See Figure 13.
15
Output Voltage (V)
12
9
6
35 Vin
3
48 Vin
55 Vin
0
0
10
20
30
40
50
Load Current (A)
60
70
80
Figure 17: Output voltage vs. load current for different input voltages showing
typical current limit curves.
Product # BQ55120QZB67
Phone 1-888-567-9596
Figure 18: Load current (50A/div) as a function of time when the converter
attempts to turn on into a 1mΩ short circuit. Top trace (1ms/div) is an expansion
of the on-time portion of the bottom trace.
www.synqor.com
Doc.# 005-0006255 Rev. C
02/10/16
Page 8
Input:
Output:
Current:
Package:
Applications Section
35-55V
12V
67 A
Quarter-brick
BASIC OPERATION AND FEATURES
CONTROL FEATURES
With voltages dropping and currents rising, the economics
of an Intermediate Bus Architecture (IBA) are becoming
more attractive, especially in systems requiring multiple
low voltages. IBA systems separate the role of isolation and
voltage scaling from regulation and sensing. The BusQor
series bus converter provides isolation and an unregulated
voltage step down in one compact module, leaving regulation
to simpler, less expensive non-isolated converters.
REMOTE ON/OFF (Pin 2): The ON/OFF input, Pin 2,
permits the user to control when the converter is on or off.
This input is referenced to the return terminal of the input
bus, Vin(-).
In the negative logic version, the ON/OFF signal is active
low (meaning that a low turns the converter on). Figure B
is a detailed look of the internal ON/OFF circuitry.
In Figure A below, the BusQor module provides the isolation
stage of the IBA system. The isolated bus then distributes
power to the non-isolated buck regulators to generate the
required voltage levels at the points of load. In this case, the
bucks are represented with SynQor’s NiQor series of nonisolated DC/DC converters. In many applications requiring
multiple low voltage outputs, significant savings can be
achieved in board space and overall system costs
When designing an IBA system with bus converters, the
designer can select from a variety of bus voltages. While
there is no universally ideal bus voltage, most designs
employ one of the following: 12 V, 9.6 V, 7.5 V, 5 V, or 3.3
V. Higher bus voltages can lead to lower efficiency for the
buck regulators but are more efficient for the bus converter
and provide lower board level distribution current. Lower
bus voltages offer the opposite trade offs.
3.3 V
100 K
On/Off
10 K
TTL
220 pF
Vin(-)
Figure B: Internal ON/OFF pin circuitry
SynQor’s BusQor modules act as a true dc transformer. The
output voltage is proportional to the input voltage, with a
specified “turns ratio” or voltage ratio, plus minor drop from
the internal resistive losses in the module. When used in
IBA systems, the output variation of the BusQor must be in
accordance with the input voltage range of the non-isolated
converters being employed.
The BusQor architecture is very scalable, meaning multiple
bus converters can be connected directly in parallel to allow
current sharing for higher power applications.
3.3 V
Front End
48 Vdc
35 - 55 V
BusQor
Converter
12.0 Vdc
2.5 V
1.8 V
1.5 V
0.9 V
Typical User Board
Converters
Loads
Figure A: Example of Intermediate Bus Architecture using BusQor bus converter
and NiQor non-isolated converters
Product # BQ55120QZB67
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006255 Rev. C
02/10/16
Page 9
Input:
Output:
Current:
Package:
Applications Section
35-55V
12V
67 A
Quarter-brick
PROTECTION FEATURES
Input Under-Voltage Lockout: The converter is designed
to turn off when the input voltage is too low, helping avoid
an input system instability problem, described in more detail
in the application note titled “Input System Instability”. The
lockout circuitry is a comparator with DC hysteresis. When
the input voltage is rising, it must exceed the typical TurnOn Voltage Threshold value (listed on the specification
page) before the converter will turn on. Once the converter
is on, the input voltage must fall below the typical Turn-Off
Voltage Threshold value before the converter will turn off.
Also see Figure E.
Output Current Limit: The output of the BusQor module
is electronically protected against output overloads. When
an overload current greater than the “DC Current-Limit
Inception” specification is drawn from the output, the
output shuts down to zero volt after a typical period of 1
ms (see Figure C). The converter remains in the off state
for ~ 800 ms (Figure D) after which the BusQor tries to
power up again (10 ms). If the overload persists, the output
voltage will go through repeated cycles of shutdown and
restart with a duty cycle of 1.25% (On) and 98.75% (Off)
respectively. The BusQor module returns (auto resetting)
to normal operation once the overload is removed. The
BusQor is designed to survive in this mode indefinitely
without damage and without human intervention.
Output
Current
100 A
peak
Output
Voltage
< 12 V
0V
Time
810 ms
10 ms
Figure D: Output Short Circuit and Auto-Resetting protection diagram (not to
scale)
Output Short Circuit Protection: When the output of the
BusQor module is shorted, a peak current of typically 100 A
will flow into the short circuit for a period of about 0.5 ms.
The output of the BusQor will shutdown to zero for ~ 800 ms
(Figure D). At the end of the shutdown period the BusQor
module tries to restart. If the short circuit persists, the
output voltage will go through repeated cycles of shutdown
and restart. The BusQor module returns (auto resetting) to
normal operation once the short circuit is removed. The
BusQor is designed to survive in this mode indefinitely
without damage and without human intervention.
In the Auto resetting mode, also referred to as “Hiccup”
mode, the power drawn from the 48 V input is about 5
Watts, most of which is dissipated into the external fault. It
is important that copper traces and pads from the output
circuit be designed to withstand the short term peaks,
although the average current into the fault may be as low
as 0.1 A typical. See Figure 18 for appropriate waveform.
Output
Current
78 A
67 A
Output
Voltage
12.0 V
Over-Temperature Shutdown: A temperature sensor
on the converter senses the average temperature of the
module. The thermal shutdown circuit is designed to turn the
converter off when the temperature at the sensed location
reaches the Over-Temperature Shutdown value. It will allow
the converter to turn on again when the temperature of the
sensed location falls by the amount of the Over-Temperature
Shutdown Restart Hysteresis value.
0V
1 ms
Time
Figure C: Output Overload protection diagram (not to scale)
Product # BQ55120QZB67
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006255 Rev. C
02/10/16
Page 10
Input:
Output:
Current:
Package:
Applications Section
APPLICATION CONSIDERATIONS
35-55V
12V
67 A
Quarter-brick
0.01”
Start-up Considerations: When powering-up, the module must charge
all its load capacitance. If a load is present during power-up, then in
addition to charging the output capacitance the module must also deliver
energy to that load. If the load is resistive then the power to the load
will incrementally increase as the output voltage increases. However, if
the load is constant-current then the load will be fully applied from a low
output voltage. Therefore the constant-current load requires more energy
at power-up. The simultaneous charging of the output capacitance while
delivering power to a load can slow down the rise of output voltage of the
module. This delay to full power-up may appear to the module as a load
fault. That appearance of a load fault will cause the module to shut down
and then attempt to re-start after a delay. To avoid this condition and
ensure a successful start-up, at power-up the module load should be half
or less of the rated power, and the load should be resistive.
Start-Up Inhibit Period: Figure E details the Start-Up Inhibit Period
for the BusQor module. At time t0, when Vin is applied with On/Off pin
asserted (enabled), the BusQor output begins to build up. Before time t1,
when the input voltage is below the UVL threshold, the unit is disabled
by the Input Under-Voltage Lockout feature. When the input voltage rises
above the UVL threshold, the Input Under-Voltage Lockout is released, and
a typical Startup Inhibit Period of 12 ms is initiated. The output builds up to
90% of the nominal value of 12.0 V in a period of 5 ms typical (50% load).
At time t2, when the On/Off pin is de-asserted (disabled), the BusQor output
instantly drops to 0V. Fall time from 12.0 V to 0 V is dependent on output
capacitance and any parasitic trace inductance in the output load circuit.
At time t3, when the On/Off pin is re-asserted (enabled), the BusQor module
output begins to build up after the inhibit period of 800 ms typical has elapsed.
Refer to the Control Features section of the data sheet for
details on enabling and disabling methods for Bus Qor modules.
0.023”
Bridging
Capacitor
0.01”
1.50”
Secondary
Primary
Figure F: Keep Out Areas for BusQor module (view from bottom)
Component Keep Out Area: Keep out areas for components not
referenced to the Primary circuit are shown in shaded areas in Figure F.
The keep out areas shown are consistent with UL’s requirements for Basic
Insulation of 0.04” (40 mils) for Pollution degree 2. User should consult UL
standards for other insulation classes and operating environments.
For applications that require mounting parts BELOW the BusQor
module, one should be aware of potential high levels of electromagnetic
interference, in addition to safety keep out. Users are advised to consult
SynQor Applications engineering in such applications.
Copper Keep Out Area: Keep out areas shown in Figure F are to be
observed for Top layer copper traces and vias. Internal layers buried one
or more layers may be exempt, depending on the PCB material grade and
thickness. Users are advised to consult UL standards for details.
All layers including top and bottom, are subject to the keep out areas
shown around Primary pins of BusQor module. Actual keep outs along the
surface (Creepage) may vary depending on the PCB material CTI. Users
are advised to consult UL standards for details.
Vin
UVLO
On/Off
(N logic)
OFF
ON
t0
t1
t2
t
t3
Vout
Start-up
Inhibit
Fault Inhibit
Bridging Components: Bridging components like EMI filter capacitors
required to be placed as close as possible to the BusQor module for
optimum performance must observe the clearance/creepage requirements
of 0.04” (40 mils) between pads to maintain compliance to UL standards
for the overall power system.
Note: Referenced keep out widths are adequate to withstand UL’s Basic
Insulation Dielectric strength tests for approved PCB materials. Applications
requiring Double or Reinforced insulation must double the keep out widths
shown in Figure F. Keep out areas shown have standard margins above
UL’s minimum requirements.
Time
Start-Up
Figure E: Power Up/Down Diagram showing Start-Up Inhibit Period
(not to scale)
Product # BQ55120QZB67
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006255 Rev. C
02/10/16
Page 11
Input:
Output:
Current:
Package:
Applications Section
35-55V
12V
67 A
Quarter-brick
Deviation from 50/50 Sharing (%)
20.0%
15.0%
48 Vin
BusQor module
10.0%
CM EMI
filter
5.0%
0.0%
(Not shown
in Figure H)
Bulk
Cap
BusQor module
-5.0%
Input LC filters
-10.0%
Module 1
-15.0%
Module 2
-20.0%
0
10
20
30
40
50
60
70
80
90
100 110 120 130
Total Load Current (A)
Figure G: Current share performance of 2 paralleled modules
Current Sharing: BusQor modules are designed to operate in parallel
without the use of any external current share circuitry. Current share is
achieved through "droop share". An output capacitor is recommended
across each module located close to the converter for optimum filtering and
noise control performance. Dedicated input inductors are recommended
but are considered optional. Input capacitors must be located close to the
converter module. PCB layout in the input circuit should be such that high
frequency ripple currents of each module is restricted to a loop formed
by the input capacitors and the input terminals of the BusQor module.
See Figure H for details on PCB layout. If needed, please contact SynQor
application engineering for further assistance on PCB trace design.
Product # BQ55120QZB67
Phone 1-888-567-9596
Figure H: Recommended PCB layout for input circuit
The typical current share performance of two paralleled modules is
illustrated in the graph shown in Figure G. In this graph the percent
deviation from ideal sharing (50%) is plotted for each module versus
the total output load current at 48Vin. Since current sharing is achieved
through droop share, the system board impedances (non common
impedances) can affect the overall sharing performance. For additional
assistance in implementing current sharing please consult the application
note titled "Paralleling Capability of SynQor Converters" and / or consult
SynQor application engineering.
www.synqor.com
Doc.# 005-0006255 Rev. C
02/10/16
Page 12
Input:
Output:
Current:
Package:
Ordering Information
35-55V
12V
67 A
Quarter-brick
Part Numbering System
Ordering Information
The part numbering system for SynQor’s dc-dc converters follows the format
shown in the example below.
The tables below show the valid model numbers and ordering options for
converters in this product family. When ordering SynQor converters, please
ensure that you use the complete 15 character part number consisting of
the 12 character base part number and the additional characters for options.
Add “-G” to the model number for 6/6 RoHS compliance.
BQ 5 5 1 2 0 Q Z B 6 7
N R S - G
6/6 RoHS
Options
(see
Ordering Information)
Model Number
Input Voltage
BQ55120QZB67xyz-G
35-55V
Output
Voltage
12V
Max Output
Current
67A
Output Current
Thermal Design
Performance Level
Package Size
The following options must be included in place of the w x y z spaces in the
model numbers listed above.
Output Voltage
Input Voltage
Product Family
Thermal Design
B - Baseplated
The first 12 characters comprise the base part number and the last 3
characters indicate available options. The “-G” suffix indicates 6/6 RoHS
compliance.
Options Description: w x y z
Enable Logic
Pin Style
N - Negative
N - 0.145"
R - 0.180"
Feature Set
S - Standard
Application Notes
A variety of application notes and technical white papers can be downloaded
in pdf format from our website.
RoHS Compliance: The EU led RoHS (Restriction of Hazardous
Substances) Directive bans the use of Lead, Cadmium, Hexavalent
Chromium, Mercury, Polybrominated Biphenyls (PBB), and Polybrominated
Diphenyl Ether (PBDE) in Electrical and Electronic Equipment. This SynQor
product is 6/6 RoHS compliant. For more information please refer to
SynQor’s RoHS addendum available at our RoHS Compliance / Lead Free
Initiative web page or e-mail us at [email protected].
Not all combinations make valid part numbers, please contact SynQor for
availability.
Contact SynQor for further information and to order:
PATENTS
Phone:
Toll Free:
Fax:
E-mail:
Web:
Address:
Product # BQ55120QZB67
978-849-0600
888-567-9596
978-849-0602
[email protected]
www.synqor.com
155 Swanson Road
Boxborough, MA 01719
USA
Phone 1-888-567-9596
SynQor holds numerous U.S. patents, one or more of which apply to most of its power converter
products. Any that apply to the product(s) listed in this document are identified by markings on
the product(s) or on internal components of the product(s) in accordance with U.S. patent laws.
SynQor’s patents include the following:
5,999,417
6,222,742
6,545,890
6,594,159
6,731,520
6,894,468
6,896,526
6,927,987
7,050,309
7,072,190
7,085,146
7,119,524
7,269,034
7,272,021
7,272,023
7,558,083
7,564,702
7,765,687
7,787,261
8,023,290
8,149,597
8,493,751
8,644,027
9,143,042
WARRANTY
SynQor offers a three (3) year limited warranty. Complete warranty
information is listed on our website or is available upon request from SynQor.
www.synqor.com
Doc.# 005-0006255 Rev. C
02/10/16
Page 13
Similar pages