LCD Segment Drivers Standard Segment Drivers BU9795AKV,BU9795AFV,BU9795AGUW,BU9794AKV,BU97950FUV No.10044EAT06 ●Description ROHM standard function segment driver series achieve “Ultra-Low power consumption”. Also these drivers need not external components. And this driver series is very simple that only has segment driver function. So, these driver series are very suitable to add in LCD display function for various applications. ●Features (BU9795AKV/FV/GUW, BU9794AKV) 1) 3wire serial interface 2) Integrated RAM for display data (DDRAM) 3) Power supply circuit for LCD driving 1/2, 1/3Bias selectable 1/4Duty Integrated Buffer AMP 4) Integrated Oscillation circuit 5) Integrated Power-on Reset circuit 6) No external components 7) Support blink function 8) Support standby mode 9) Low voltage / Ultra low power consumption design 10) Support unity voltage supply (BU9795AKV/FV/GUW) 11) Support Independent power supply circuit for LCD driving (BU9794AKV) ●Features (BU97950FUV) 1) 2wire serial interface 2) Integrated RAM for display data (DDRAM) 3) Integrated Power supply circuit for LCD driving 1/4 Bias 1/8 Duty Integrated Buffer AMP 4) Integrated Oscillation circuit 5) Integrated Power-on Reset circuit 6) No external components 7) Support standby mode 8) Low voltage / Ultra low power consumption design 9) Integrated Electrical volume register (EVR) function 10) Support Register Read function 11) Support Independent power supply circuit for LCD driving ●Applications Telephone, FAX, Portable equipment (POS, ECR, PDA etc.), DSC, DVC, Car Audio, Home electrical appliance, Meter equipment, Healthcare equipment etc. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 1/14 2011.03 - Rev.A Technical Note BU9795AKV,BU9795AFV,BU9795AGUW,BU9794AKV,BU97950FUV ●Line up matrix BU9795A Parameter BU9794AKV BU97950FUV 31 50 35 4 4 4 8 140 108 124 200 280 - - - - Yes - - - Yes Yes KV FV GUW Segment output 35 27 Common output Total display dot number Adjustable contrast function 4 Support split voltage supply Interface 3wire 3wire 3wire 3wire 2wire Package VQFP48C SSOP-B40 VBGA48W040 VQFP64 TSSOP-C48V ●Absolute maximum ratings (VSS=0V) BU9795AKV /FV/GUW Parameter Power Supply Voltage 1 (VDD) BU9794AKV BU97950FUV -0.5～+7.0 Power Supply Voltage 2 (VLCD) Unit V Power supply -0.5～VDD -0.5～+7.0 -0.5～+7.0 V LCD drive Voltage 0.6*1 0.7*2 3 0.27* 0.75*4 0.75*4 W Allowable loss at package only Allowable Loss (Pd) Input Voltage Range (VIN) -0.5～VDD+0.5 V Operational Temperature Range (Topr) -40～+85 ℃ Storage Temperature Range (Tstg) -55～+125 ℃ *1 *2 *3 *4 Remarks When use more than Ta=25℃, subtract 6.0mW per degree (BU9795AKV) When use more than Ta=25℃, subtract 7.0mW per degree (BU9795AFV) When use more than Ta=25℃, subtract 2.7mW per degree (BU9795AGUW) When use more than Ta=25℃, subtract 7.5mW per degree (BU9794AKV, BU97950FUV) ●Recommend operating conditions (Ta=-40~85℃, VSS=0V) BU9795AKV /FV/GUW*1 Parameter BU9794AKV Min. Typ. Max. Min. BU97950KV Typ. Max. Min. Unit Remarks Typ. Max. Power Supply Voltage 1 (VDD) 2.5 - 5.5 2.5 - 5.5 2.5 - 5.5 V Power supply Power Supply Voltage 2 (VLCD) 0 - VDD -2.4 2.5 - 5.5 2.5 - 5.5 V LCD drive Voltage *1 Please use VDD-VLCD 2.4V condition. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 2/14 2011.03 - Rev.A Technical Note BU9795AKV,BU9795AFV,BU9795AGUW,BU9794AKV,BU97950FUV ●Electrical characteristics <BU9795AKV/FV/GUW> DC Characteristics (VDD=2.5~5.5V, VSS=0V, Ta=-40~85℃, unless otherwise specified) Limits Parameter Symbol Unit Min. Typ. Max. Condition “H” level input voltage VIH 0.7VDD - VDD V SD, SCL, CSB “L” level input voltage VIL VSS - 0.3VDD V SD, SCL, CSB “H” level input current IIH - - 1 µA SD, SCL, CSB “L” level input current IIL -1 - - µA SD, SCL, CSB SEG RON - 3.5 - kΩ COM RON - 3.5 - kΩ VLCD 0 - VDD -2.4 V Ist - - 5 µA Display off, Oscillator off LCD Driver on resistance VLCD supply voltage Standby current Iload=±10µA VDD-VLCD 2.4V Power consumption 1 IDD1 - 12.5 30 µA VDD=3.3[V], Ta=25℃, Power save mode1, FR=70Hz 1/3 bias, Frame inverse Power consumption 2 IDD2 - 20 40 µA VDD=3.3[V], Ta=25℃, Normal mode, FR=80Hz 1/3 bias, Line inverse Oscillation Characteristics (VDD=2.5~5.5V,VSS=0V, Ta=-40~85℃) Limits Parameter Symbol Min. Typ. Max. Unit Condition Frame frequency fCLK 56 80 104 Hz FR = 80Hz setting Frame frequency1 fCLK1 70 80 90 Hz VDD=3.5V, 25℃ MPU interface Characteristics(VDD=2.5V~5.5V,VSS=0V, Ta=-40~85℃) Limits Parameter Symbol Min. Typ. Max. Input rise time tr Input fall time - - 80 Unit Condition ns tf - - 80 ns SCL cycle time tSCYC 400 - - ns “H” SCL pulse width tSHW 100 - - ns “L” SCL pulse width tSLW 100 - - ns SD setup time tSDS 20 - - ns SD hold time tSDH 50 - - ns CSB setup time tCSS 50 - - ns CSB hold time tCSH 50 - - ns “H” CSB pulse width tCHW 50 - - ns tCHW CSB tCSS tf tSCYC tr tCSH tSLW SCL tSHW tSDS tSDH SD Fig.1 Interface Timing (BU9795AKV/FV/GUW) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 3/14 2011.03 - Rev.A Technical Note BU9795AKV,BU9795AFV,BU9795AGUW,BU9794AKV,BU97950FUV <BU9794AKV> DC Characteristics (VDD=2.5~5.5V, VLCD=2.5~5.5V, VSS=0V, Ta=-40~85℃, unless otherwise specified) Limits Parameter Symbol Unit Condition Min. Typ. Max. “H” level input voltage VIH 0.8VDD - VDD V SD,SCL,CSB “L” level input voltage VIL VSS - 0.2VDD V SD,SCL,CSB “H” level input current IIH - - 1 µA SD,SCL,CSB “L” level input current IIL -1 - - µA SD,SCL,CSB SEG RON - 3.5 - kΩ COM RON - 3.5 - kΩ Ist - - 5 µA Display off, Oscillation off Power consumption 1 IDD - 5 15 µA VDD=3.3V, VLCD=5V, Ta=25℃ Power save mode1, FR=70Hz 1/3 bias, Frame inverse Power consumption 2 ILCD - 10 20 µA VDD=3.3V, VLCD=5V, Ta=25℃ Power save mode1, FR=70Hz 1/3 bias, Frame inverse LCD Driver on resistance Standby current Iload=±10µA Oscillation Characteristics (VDD=2.5~5.5V, VLCD=2.5~5.5V, VSS=0V, Ta=-40~85℃, unless otherwise specified) Limits Parameter Symbol Unit Condition Min. Typ. Max. Frame frequency fCLK 68 80 92 Hz FR = 80Hz setting, VDD=3.3V MPU interface Characteristics (VDD=2.5~5.5V, VLCD=2.5~5.5V, VSS=0V, Ta=-40~85℃, unless otherwise specified) Limits Unit Condition Parameter Symbol Min. Typ. Max. Input rise time tr Input fall time - - 80 ns tf - - 80 ns SCL cycle time tSCYC 400 - - ns “H” SCL pulse width tSHW 100 - - ns “L” SCL pulse width tSLW 100 - - ns SD setup time tSDS 20 - - ns SD hold time tSDH 50 - - ns CSB setup time tCSS 50 - - ns CSB hold time tCSH 50 - - ns “H” CSB pulse time tCHW 50 - - ns tCHW CSB tCSS tCSH tr tSCYC tf tSLW SCL tSHW tSDS tSDH SD Fig.2 Interface Timing (BU9794AKV) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 4/14 2011.03 - Rev.A Technical Note BU9795AKV,BU9795AFV,BU9795AGUW,BU9794AKV,BU97950FUV <BU97950FUV> DC Characteristics (VDD=2.5~5.5V, VLCD=2.5~5.5V, VSS=0V, Ta=-40~85℃, unless otherwise specified) Limits Parameter Symbol Unit Conditions Min. Typ. Max. “H” level input voltage VIH 0.7VDD - VDD V SDA,SCL “L” level input voltage VIL VSS - 0.3VDD V SDA,SCL “H” level input current IIH - - 1 µA SDA,SCL SDA,SCL “L” level input current IIL -1 - - µA SEG RON - 3.5 - kΩ COM RON - 3.5 - kΩ Ist - - 5 µA Power consumption 1 IDD - 2.5 15 µA Power consumption 2 ILCD - 10 20 µA LCD Driver on resistance Standby current Iload=±10µA Display off, Oscillation off VDD=3.3V, VLCD=5V, Ta=25℃ Power save mode1, FR=80Hz 1/4 bias, Frame inverse VDD=3.3V, VLCD=5V, Ta=25℃ Power save mode1, FR=80Hz 1/4 bias, Frame inverse Oscillation Characteristics (VDD=2.5~5.5V, VSS=0V, Ta=-40~85℃, unless otherwise specified) Limits Parameter Symbol Unit Min. Typ. Max. Frame frequency fCLK 56 80 104 Hz Condition Power save mode FR = Normal mode MPU interface Characteristics (VDD=2.5~5.5V, VLCD=0V, VSS=0V, Ta=-40~85℃, unless otherwise specified) Limits Parameter Symbol Unit Condition Min. Typ. Max. Input rise time tr - - 0.3 µs Input fall time tf - - 0.3 µs SCL cycle time tSCYC 2.5 - - µs “H” SCL pulse width tSHW 0.6 - - µs “L” SCL pulse width tSLW 1.3 - - µs SDA setup time tSDS 200 - - ns SDA hold time tSDH 0 - - ns Bus free time tBUF 1.3 - - µs START condition hold time tHD;STA 0.6 - - µs START condition setup time tSU;STA 0.6 - - µs STOP condition setup time tSU;STO 0.6 - - µs SDA tf tSLW tBUF tSCYC S CL tHD;STA tr tSDH tSHW tSDS SDA tSU;STO tSU;STA Fig.3 interface timing (BU97950FUV) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 5/14 2011.03 - Rev.A Technical Note BU9795AKV,BU9795AFV,BU9795AGUW,BU9794AKV,BU97950FUV ●Block Diagram / Pin Arrangement / Terminal Description <BU9795AKV> ●Block Diagram ●Pin Arrangement COM1 ＋ LCD BIAS SELECTOR － common counter ＋ － blink timing generator DDRAM VLCD INHb Command Data Decoder Command register OSCIN SEG25 SEG24 25 SEG26 SEG27 SEG28 SEG29 SEG30 Segment driver SEG31 common driver SEG32 LCD voltage generator SEG33 VDD SEG34 SEG0……SEG34 36 COM0 COM0……COM3 37 24 SEG23 COM2 SEG22 COM3 SEG21 VLCD SEG20 VDD SEG19 VSS SEG18 OSCIN SEG17 CSB SEG16 SCL SEG15 SD SEG14 TEST OSCILLATOR Power On Reset INHb serial inter face SEG13 SEG12 13 48 SD SEG10 SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 1 CSB SEG1 SEG0 TEST SEG11 12 IF FILTER VSS SCL Fig.4 Block Diagram (BU9795AKV) Fig.5 Pin Arrangement (BU9795AKV) ●Terminal Description Terminal Terminal No. I/O INHb 48 I TEST 47 I OSCIN 43 I External clock input Ext clock and Int clock can be changed by command. Must be connect to VSS when use internal oscillation circuit. SD 46 I serial data input SCL 45 I serial data transfer clock CSB 44 I Chip select : VSS 42 - GND VDD 41 - Power supply VLCD 40 - Power supply for LCD driving SEG0-34 1-35 O SEGMENT output for LCD driving COM0-3 36-39 O COMMON output for LCD driving www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. Function Input terminal for turn off display H: turn on display L: turn off display Test input (ROHM use only) Must be connect to VSS “L” active 6/14 2011.03 - Rev.A Technical Note BU9795AKV,BU9795AFV,BU9795AGUW,BU9794AKV,BU97950FUV <BU9795AFV> ●Block Diagram ●Pin Arrangement COM0……COM3 SEG4……SEG30 common driver Segment driver SEG28 SEG29 COM0 SEG30 COM2 COM1 COM3 VDD VLCD VSS CSB OSCIN SDA SCL INHb TEST SEG5 SEG4 SEG7 LCD voltage generator SEG6 VDD ＋ LCD BIAS SELECTOR － common counter ＋ － blink timing generator 40 21 1 20 DDRAM OSCILLATOR Power On Reset SEG27 SEG26 SEG25 SEG24 SEG23 SEG22 SEG21 SEG20 SEG19 SEG18 SEG17 SEG16 SEG15 SEG14 SEG13 SEG12 SEG11 OSCIN SEG10 Command Data Decoder Command register SEG9 INHb SEG8 VLCD serial inter face IF FILTER VSS TEST CSB SD SCL Fig.6 Block Diagram (BU9795AFV) Fig.7 Pin Arrangement (BU9795AFV) ●Terminal Description Terminal Terminal No. I/O INHb 36 I TEST 35 I OSCIN 31 I External clock input Ex clock and Int clock can be changed by command. Must be connect to VSS when use internal oscillation circuit. SD 34 I serial data input SCL 33 I serial data transfer clock CSB 32 I Chip select : “L” active VSS 30 - GND VDD 29 - Power supply VLCD 28 - Power supply for LCD driving SEG4-30 1-23, 37-40 O SEGMENT output for LCD driving COM0-3 24-27 O COMMON output for LCD driving www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. Function Input terminal for turn off display H: turn on display L: turn off display Test input (ROHM use only) Must be connect to VSS 7/14 2011.03 - Rev.A Technical Note BU9795AKV,BU9795AFV,BU9795AGUW,BU9794AKV,BU97950FUV <BU9795AGUW> ●Block Diagram ●Pin Arrangement COM0……COM3 SEG2……SEG32 common driver Segment driver 1 2 3 4 5 6 7 G (NC) SEG13 SEG15 SEG18 SEG20 SEG22 (NC) F SEG11 SEG12 SEG16 SEG17 SEG21 SEG23 SEG24 E SEG9 SEG10 SEG14 SEG19 SEG25 SEG27 SEG26 D SEG7 SEG6 SEG8 SEG5 SEG30 SEG28 SEG29 C SEG4 SEG3 SEG2 CSB COM3 SEG32 SEG31 INHb SD VSS VDD COM1 COM0 TEST2 SCL OSCIN VLCD COM2 (NC) VDD LCD voltage generator ＋ LCD BIAS SELECTOR － common counter ＋ － blink timing generator DDRAM VLCD INHb Command Data Decoder Command register OSCIN OSCILLATOR Power On Reset B serial inter face A IF FILTER VSS TEST CSB SD (NC) SCL Fig.8 Block Diagram (BU9795AGUW) Fig.9 Pin Arrangement (BU9795AGUW) ●Terminal Description Terminal I/O Function Input terminal for turn off display H: turn on display L: turn off display Test input (ROHM use only) Must be connect to VSS INHb I TEST I OSCIN I External clock input Ex clock and Int clock can be changed by command. Must be connect to VSS when use internal oscillation circuit. SD I serial data input SCL I serial data transfer clock CSB I Chip select : VSS - GND VDD - Power supply VLCD - Power supply for LCD driving SEG2-32 O SEGMENT output for LCD driving COM0-3 O COMMON output for LCD driving “L” active (Caution) About terminal number, please refer to above pin arrangement www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 8/14 2011.03 - Rev.A Technical Note BU9795AKV,BU9795AFV,BU9795AGUW,BU9794AKV,BU97950FUV <BU9794AKV> ●Block Diagram ●Pin Arrangement Segment driver SEG38 ＋ － LCD BIAS SELECTOR common counter ＋ － blink timing generator DDRAM VSS INHb Command Data Decoder Command register OSCIN SEG23 SEG24 SEG25 SEG26 SEG27 SEG28 SEG29 SEG30 SEG31 SEG32 SEG33 SEG34 SEG22 33 common driver SEG35 LCD voltage generator SEG36 SEG0……SEG49 48 SEG37 COM0……COM3 VLCD 49 32 SEG21 SEG39 SEG20 SEG40 SEG19 SEG41 SEG18 SEG42 SEG17 SEG43 SEG16 SEG44 SEG15 SEG45 SEG14 SEG46 SEG13 SEG47 SEG12 SEG48 SEG11 SEG49 SEG10 COM0 SEG9 COM1 SEG8 COM2 OSCILLATOR Power On Reset COM3 serial inter face SEG7 SEG6 17 64 TEST2 TEST1 CSB SD SEG5 16 SEG4 SEG3 SEG2 SEG1 SEG0 TEST2 TEST1 INHb SD SCL CSB OSCIN VSS VLCD IF FILTER VSS VDD 1 VDD SCL Fig.10 Block Diagram (BU9794AKV) Fig.11 Pin Arrangement (BU9794AKV) ●Terminal Description Terminal Terminal No. I/O INHb 8 I TEST1 9 I TEST2 10 I OSCIN 4 I External clock input Ex clock and Int clock can be changed by command. Must be connect to VSS when use internal oscillation circuit. SD 7 I serial data input SCL 6 I serial data transfer clock CSB 5 I Chip select : VSS 3 - GND VDD 2 - Power supply VLCD 1 - Power supply for LCD driving SEG0-49 11-60 O SEGMENT output for LCD driving COM0-3 61-64 O COMMON output for LCD driving www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. Function Input terminal for turn off display H: turn on display, L: turn off display Test input (ROHM use only) Must be connect to VSS Test input (ROHM use only) Must be connect to VSS “L” active 9/14 2011.03 - Rev.A Technical Note BU9795AKV,BU9795AFV,BU9795AGUW,BU9794AKV,BU97950FUV <BU97950FUV> ●Block Diagram VLCD ●Pin Arrangement COM0……COM7 SEG0……SEG34 common driver Segment driver LCD voltage generator COM4 COM5 COM6 COM7 SEG2 SEG1 SEG0 SEG33 COM3 SEG32 SEG9 SEG3 SEG31 SEG10 COM2 SEG30 SEG11 SEG4 SEG29 SEG12 COM1 SEG28 SEG13 SEG5 SEG27 SEG14 COM0 SEG26 SEG15 SEG6 SEG25 SEG16 SEG34 SEG24 SEG17 SEG7 SEG23 SEG18 SEG8 SEG22 SEG19 SCL SEG21 SDA LCD BIAS SELECTOR － VDD ＋ VLCD － SEG20 ＋ ＋ common counter － DDRAM ＋ － VSS OSCILLATOR Power On Reset Command Data Decoder VSS Command register serial inter face IF FILTER VDD SDA SCL Fig.12 Block Diagram (BU97950FUV) Fig.13 Pin Arrangement (BU97950FUV) ●Terminal Description Terminal Terminal No. I/O SDA 48 I/O SCL 47 I serial data transfer clock VSS 3 - GND VDD 1 - Power supply VLCD 2 - Power supply for LCD driving SEG0-35 4-24 33-46 O SEGMENT output for LCD driving COM0-7 25-32 O COMMON output for LCD driving www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. Function serial data input register read data output port 10/14 2011.03 - Rev.A BU9795AKV,BU9795AFV,BU9795AGUW,BU9794AKV,BU97950FUV Technical Note ●IO Equivalent Circuit <BU9795AKV/FV/GUW> VDD VDD VLCD OSCIN VSS VSS VDD VDD CSB, SD, SCL VSS VSS VLCD VDD INHb SEG/COM VSS VLCD VDD TEST VSS Fig.14 I/O equivalent circuit (BU9795AKV/FV/GUW) <BU9794AKV> VDD VLCD VSS VSS VDD VLCD CSB, SD, SCL INHb,TEST1,TEST2 SEG/COM VSS VLCD VDD OSCIN VSS Fig.15 I/O equivalent circuit (BU9794AKV) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 11/14 2011.03 - Rev.A BU9795AKV,BU9795AFV,BU9795AGUW,BU9794AKV,BU97950FUV Technical Note <BU97950FUV> VDD VLCD VSS VSS SDA SCL VSS VSS VLCD SEG/COM VSS Fig.16 I/O equivalent circuit (BU97950FUV) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 12/14 2011.03 - Rev.A Technical Note BU9795AKV,BU9795AFV,BU9795AGUW,BU9794AKV,BU97950FUV ●Ordering part number B U 9 Part No. 7 9 5 A G Part No. BU9795A BU9794A BU97950 U W - Package FV : SSOP-B40 GUW : VBGA048W040 KV : VQFP48C KV : VQFP64 FUV : TSSOP-C48V E 2 Packaging and forming specification E2: Embossed tape and reel SSOP-B40 <Tape and Reel information> 13.6 ± 0.2 (MAX 13.95 include BURR) 0.5 ± 0.2 1 2000pcs Direction of feed E2 The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand ) 20 0.15 ± 0.1 0.1 1.8 ± 0.1 Embossed carrier tape Quantity 21 5.4 ± 0.2 7.8 ± 0.3 40 Tape 0.1 S 0.65 0.22 ± 0.1 0.08 M 1pin Reel (Unit : mm) Direction of feed ∗ Order quantity needs to be multiple of the minimum quantity. VBGA048W040 <Tape and Reel information> 4.0 ± 0.1 4.0±0.1 P=0.5×6 A 0.5 G F E D C B A B 2500pcs Direction of feed E2 The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand ) S 0.5 P=0.5 × 6 0.08 S 0.5±0.1 48- φ 0.295±0.05 φ 0.05 M S AB Embossed carrier tape (with dry pack) Quantity 0.5 ± 0.1 0.10 0.9MAX 1PIN MARK Tape 1pin 12 3 4 5 6 7 Reel (Unit : mm) Direction of feed ∗ Order quantity needs to be multiple of the minimum quantity. TSSOP-C48V <Tape and Reel information> 12.5±0.1 (MAX 12.85 include BURR) 25 0.5±0.15 1.0±0.2 8.1±0.2 6.1±0.1 48 +6 4 −4 0.5 1 1PIN MARK Tape Embossed carrier tape (with dry pack) Quantity 2000pcs Direction of feed E2 The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand ) 24 +0.05 0.17 −0.03 0.85±0.05 0.08±0.08 1.0MAX S 0.5 0.08 S +0.05 0.22 −0.04 0.08 M 1pin Reel (Unit : mm) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 13/14 Direction of feed ∗ Order quantity needs to be multiple of the minimum quantity. 2011.03 - Rev.A BU9795AKV,BU9795AFV,BU9795AGUW,BU9794AKV,BU97950FUV Technical Note VQFP48C <Tape and Reel information> 9.0 ± 0.2 7.0 ± 0.1 25 36 Embossed carrier tape Quantity 1500pcs 0.5±0.15 0.75 48 13 1 0.75 12 1.0±0.2 24 7.0±0.1 9.0±0.2 37 Tape Direction of feed E2 direction is the 1pin of product is at the upper left when you hold ( The ) reel on the left hand and you pull out the tape on the right hand +0.05 0.145 -0.03 1.6MAX 1PIN MARK 0.1±0.05 1.4±0.05 4 +6 -4 0.5 ± 0.1 0.08 S +0.05 0.22 -0.04 0.08 Direction of feed 1pin M Reel (Unit : mm) ∗ Order quantity needs to be multiple of the minimum quantity. VQFP64 <Tape and Reel information> 12.0±0.2 10.0±0.1 48 33 1 1.0±0.2 0.5±0.15 1.25 17 64 1000pcs Direction of feed E2 direction is the 1pin of product is at the upper left when you hold ( The ) reel on the left hand and you pull out the tape on the right hand 16 1PIN MARK +0.05 0.145 -0.03 1.6MAX 1.25 Embossed carrier tape (with dry pack) Quantity 32 10.0±0.1 12.0±0.2 49 Tape 0.1±0.05 1.4±0.05 4 +6 -4 0.08 S +0.05 0.2 -0.04 0.08 M 1pin 0.5±0.1 (Unit : mm) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. Reel 14/14 Direction of feed ∗ Order quantity needs to be multiple of the minimum quantity. 2011.03 - Rev.A Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. R1120A